config Commands

config ap address

To configure the AP IPv4 or IPv6 address, use the config ap address command.

config ap address ipv4 { dhcp | static { static-ip-addr static-netmask default-gateway-ip-addr| ipv6 { auto-config { enable | disable} | dhcp | disable | link-local ipv6-addr| static ipv6-addr ipv6-prefix gateway-ipv6-addr

Syntax Description

ipv4

Configure IPv4 address

ipv6

Configure IPv6 address

auto-config

Auto configure IPv6 address
dhcp

Configure IPv6 DHCP

auto-config
auto-config

Command Default

None.

Command History

Release Modification

This command was introduced.

Usage Guidelines

Examples

Related Commands

Command Description
 
 

config ap client-trace

To configure client trace on the access point, use the config ap client-trace command.

config ap client-trace {address {add | clear-all | delete} | all-clients {enable | disable} | filter {all {enable | disable} | arp {enable | disable} | assoc {enable | disable} | auth {enable | disable} | dhcp {enable | disable} | eap {enable | disable} | icmp {enable | disable} | ndp {enable | disable} | probe {enable | disable}} | inline-mon {enable | disable} | output console-log | start | stop}

Syntax Description

addresses

Configure clients to trace. Specify the MAC address of the client

add

Specifies a client to trace

clear-all

Delete all client traces on this access point

delete

Deletes client address to be traced. Takes a client MAC address
all-clients

Trace all clients

enable

Enables trace for all clients

disable

Disables trace for all clients
filter

Sets filters for cleint tracing

all

Traces all filters

arp

Traces ARP packets

Use the enable or disable keyword to enable or disable this filter.

assoc

Traces ASSOC packets

auth

Traces auth packets

dhcp

Traces DHCP packets

eap

Traces EAP packets

icmp

Traces ICMP packets

ndp

Traces NDP packets

probe

Trace probe packets.

inline-mon

Enables or disables inline monitoring

output

Enables or disables logging to the console or log file

console-log

Specifies console log keyword

start

Starts client tracing

stop

Stops client tracking

Command Modes

Privileged EXEC (#)

Command History

Release Modification

8.1.111.0

This command was introduced.

Examples

The following example shows how to start client tracing on the AP:

cisco-ap# config ap client-trace start

config ap client-trace filter

To set filters for client trace, use the config ap client-trace filter command.

config ap client-trace filter { all[ disable | enable] | arp[ disable | enable] | assoc[ disable | enable] | auth[ disable | enable] | dhcp[ disable | enable] | eap[ disable | enable] | icmp[ disable | enable] | ndp[ disable | enable] | probe[ disable | enable] }

Syntax Description

all

Trace all filters
arp

Trace ARP packets
assoc

Trace ASSOC packets
auth

Trace auth packets
dhcp

Trace DHCP packets
eap

Trace EAP packets
icmp

Trace ICMP packets
ndp

Trace NDP Packets
probe

Trace probe packets

Command Modes

Privileged EXEC (#)

Command History

Release Modification

8.1.111.0

This command was introduced.

Examples

To set filters for client trace, use this command:

cisco-ap# config ap client-trace filter

config ap client-trace output

To configure the trace output, use the config ap client-trace output command.

config ap client-trace output console-log { disable | enable}

Syntax Description

console-log

Displays trace output to console and log
disable

Disables trace output to console and log
enable

Enables trace output to console and log

Command Modes

Privileged EXEC (#)

Command History

Release Modification

8.1.111.0

This command was introduced.

Examples

The following example shows you how to configure the trace output:

cisco-ap# config ap client-trace output

config boot baudrate

To set the baud rate, use the config boot baudrate command.

config boot baudrate { 115200 | 9600}

Syntax Description

115200

Sets the baud rate to 115200

9600

Sets the baud rate to 9600

Command Modes

Privileged EXEC (#)

Command History

Release Modification

8.1.111.0

This command was introduced.

Examples

The following example shows how to configure the baud rate to 9600:

cisco-ap# config boot baudrate 9600

config boot break

To enable break, use the config boot break command.

config boot break { enable | disable}

Syntax Description

enable

Enables boot break
disable

Disables boot break

Command Modes

Privileged EXEC (#)

Command History

Release Modification

8.1.111.0

This command was introduced.

Examples

The following example shows how to enable boot break:

cisco-ap# config boot break enable

config boot crashkernel

To enable or disable kernel crash, use the config boot crashkernel command.

config boot crashkernel { enable | disable}

Syntax Description

enable

Enables kernel crash
disable

Disables kernel crash

Command Modes

Privileged EXEC (#)

Command History

Release Modification

8.1.111.0

This command was introduced.

Examples

The following example shows how to enable kernel crash:

cisco-ap# config boot crashkernel enable

config boot debug-memory

To enable memory debug, use the config boot debug-memory command.

config boot debug-memory {enable | disable}

Syntax Description

enable

Enables memory debug
disable

Disables memory debug

Command Modes

Privileged EXEC (#)

Command History

Release Modification

8.1.111.0

This command was introduced.

Examples

This example shows you how to enable memory debug:

cisco-ap# config boot debug-memory enable

config boot manual

To enable manual boot of the AP, use the config boot manual command.

config boot manual { enable | disable}

Syntax Description

enable

Enables manual boot
disable

Disables manual boot

Command Modes

Privileged EXEC (#)

Command History

Release Modification

8.1.111.0

This command was introduced.

Examples

The following example shows how to enable manual boot:

cisco-ap# config boot manual enable

config boot path

To configure the boot path, use the config boot path command.

config boot path { 1 | 2}

Syntax Description

{1 | 2}

Path to be specified as Part 1 or Part 2

Command Modes

Privileged EXEC (#)

Command History

Release Modification

8.1.111.0

This command was introduced.

Examples

The following example shows how to configure the booth path as 1:

cisco-ap# config boot path 1

config cts debug enforcement host_ip

To filter the SGACL enforcement debugs based on the host IP, use the config cts debug enforcement host_ip command.

config cts debug enforcement host_ip { ipv4 dst-ip [ src-ip] | ipv6 dst-ip [ src-ip]}

Syntax Description

ipv4 dst-ip [src-ip]

Displays only the IPv4 SGACL enforcement debugs based on the destination and, optionally, source IP addresses
ipv6 dst-ip [src-ip]

Displays only the IPv6 SGACL enforcement debugs based on the destination and, optionally, source IP addresses

Command Modes

Privileged EXEC (#)

Command History

Release Modification

8.1.111.0

This command was introduced.

Examples

The following example shows you how to filter the IPv4 SGACL enforcement debugs based on the host IP:

cisco-ap# config cts debug enforcement host_ip ipv4 209.165.200.224 209.165.200.227

config cts debug enforcement rate

To configure the rate of printing of debug logs, use the config cts debug enforcement rate command.

config cts debug enforcement rate { X Y }

Command Modes

Privileged EXEC (#)

Syntax Description

rate

Configure the rate of printing debug logs
X

Number of packets whose debugs are to be displayed for every Y number of packets processed; valid range is between 0 to 10000

Y

Number of packets to be processed; valid range is between 0 to 10000

Command History

Release Modification

8.1.111.0

This command was introduced.

Examples

The following example shows how to configure the rate of printing of debug logs such that debugs of 100 packets are displayed for every 500 packets processed: 

cisco-ap# config cts debug enforcement rate 100 500

config cts debug enforcement permissions

To filter SGACL enforcement debugs based on source group tag (SGT) and destination group tag (DGT), use the config cts debug enforcement permissions command.

config cts debug enforcement permissions { dgt | sgt} tag-id

Syntax Description

dgt

Destination group tag
sgt

Source group tag
tag-id

Tag identifier; valid values are beteween 0 to 65535

Command Modes

Privileged EXEC (#)

Command History

Release Modification

8.1.111.0

This command was introduced.

Examples

The following example shows you how to filter SGACL enforcement debugs for a destination group tag whose ID is 600:

cisco-ap# config cts debug enforcement permissions dgt 600

config cts debug enforcement protocol

To filter SGACL enforcement debugs based on protocol, use the config cts debug enforcement protocol command.

config cts debug enforcement protocol { protocol-id | icmp | tcp | udp}

Syntax Description

protocol-id

Protocol ID; valid values are between 0 to 65535
icmp

Filter SGACL enforcement for ICMP traffic
tcp

Filter SGACL enforcement for TCP traffic
udp

Filter SGACL enforcement for UDP traffic

Command Modes

Privileged EXEC (#)

Command History

Release Modification

8.1.111.0

This command was introduced.

Examples

The following example shows you how to filter SGACL enforcement debugs based on protocol for UDP traffic:

cisco-ap# config cts debug enforcement protocol udp