Displays information
for subscriber sessions that are defined by specified keywords. Command
keywords are base commands that display distinctive types of data. Filter
keywords are a superset of command keywords that modify or filter the output of
the base commands.
Important |
Not all filter
keywords are available for all command keywords. CLI Help displays available
filter keywords based on: the platform type (ASR 5000 or ASR 5500), the
products that are licensed to run on the platform, and the preceding command
keyword and subsequent filter keywords.
|
Privilege
Security
Administrator, Administrator, Inspector, Operator
Mode
Exec
The following prompt
is displayed in the Exec mode:
[local]host_name#
Syntax
show subscribers [ command_keyword ] [ filter_keywords ] [ | { grep grep_options | more } ]
command_keyword
The following
keywords are base commands that each have a distinct display output. Only one
command keyword can be entered on the command line.
aaa-configuration
Displays
Authentication Authorization and Accounting (AAA) configuration information for
subscriber sessions defined by the specified filter keywords. The following
filter keywords are valid with this command:
active, active-charging -service, all, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hnbgw-only, hsgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-address, l3-tunnel-remote-address, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-udp-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, nemo-only network-requested, network-type, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, tx-data, username, verbose, grep, more
access-flows { accounting | dynamic |
pre-provisioned |
static
}
Shows the ip-flows
for the subscribers defined by the specified filter keywords.
-
accounting : displays the accounting type of access
flows for a subscriber.
-
dynamic : displays the dynamic type of access flows
for a subscriber.
-
pre-provisioned : displays the pre-provisioned type
of access flows for a WiMAX subscriber.
-
static : displays the static type of access flows
for a subscriber.
The following filter
keywords are valid with this command:
active, active-charging-service, all, apn, asn-peer-address, asngw-service, asnpc-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, dormant, epdg-address, epdg-service, fa, fa-service, flow-type, ggsn-service, gprs-service, gsm-traffic-class, ha, ha-ipsec-only, ha-service, henbgw-access-service, hnbgw-only, hsgw-service, idle-time, imsi, ip-address, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-address, l3-tunnel-remote-address, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-udp-tunnel-only, mme-address, mme-service, msid, msisdn, network-requested, network-type, pcf, pdg-service, pdif-service, pdsn-service, pdsnclosedrp-service, pgw-address, plmn-type, rulebase, rx-data, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, tpo, tx-data, username, verbose, grep, more
access-type { lxcdma | ehrpd | lte | undetemrined | wcdma | wifi
| wired }
Displays active
subscribers using a specific type of UE.
- 1xcdma : 1XCDMA – Wireless CDMA 1x high speed
internet service
- ehrpd : eHRPD – Enhanced High Rate Packet Data
- evdo : EvDO – EVolution-Data Optimized
- lte : LTE – Long Term Evolution
- undetermined
- wcdma : WCDMA – Wideband Code Division Multiple
Access
- wifi : WiFi – Wireless local area network
- wired
The following
filter keywords are valid with this command:
access-type, bearer-establishment, bng-service, callid, card-num, configured-idle-timeout, domain, ebi, enodeb-address, fa, firewall, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, hnbgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, mipv6ha-service, msid, nat, network-type, profile-id, profile-name, qci, rx-data, s1u-state, security-type, session-time-left, sgw-address, smgr-instance, tx-data, ue-type, username, grep, more
active
Displays active
subscribers. When no Filter Keywords are specified, the output is a summary of
all active subscribers. When Filter Keywords are specified, the percentage is
displayed as graphs in which one is displayed using a high sampling rate, a
10-second interval between samples, and a low sampling rate, a 15-minute
interval between samples.
The following
filter keywords are valid with this command:
apn, asn-peer-address, asngw-service, asnpc-service, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, pcf, pdg-service, pdif-service, pdsn-service, pdsnclosedrp-service, pgw-address, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, session-time-left, sgsn-address, sgsn-service, smgr-instance, sgw-address, sgw-service, tpo, tx-data, username, grep, more
active-charging-service
acs_service
Displays
information for subscribers being processed by the active charging service
specified as an alphanumeric string of 1 through 15 characters.
The following
filter keywords are valid with this command:
active-charging-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, configured-idle-timeout, connected-time, ebi, enodeb-address, epdg-address, epdg-service, fa, firewall, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, idle-time, ims-auth-service, imsi, ip-address, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-address, l3-tunnel-remote-address, long-duration-time-left, mag-service, mipv6ha-service, msid, nat, network-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, session-time-left, sgw-address, smgr-instance, tx-data, username, grep, more
activity
Displays
subscriber link activity percentage. When no Filter Keywords are specified, the
output is a summary of all subscriber activity. When Filter Keywords are
specified, the link activity percentage is displayed as graphs in which one is
displayed using a high sampling rate, a 10-second interval between samples, and
a low sampling rate, a 15-minute interval between samples.
The following
filter keywords are valid with this command:
active, all, apn, asn-peer-address, asngw-service, asnpc-service, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, pcf, pdg-service, pdif-service, pdsn-service, pdsnclosedrp-service, pgw-address, plmn-type, profile-id, profile-name, qci, rx-data, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tpo, tx-data, username, grep, more
all
ip_address
Displays all current subscribers who have either active or
dormant sessions.
apn
apn_string
Displays subscribers currently facilitated by the Access Point
name (APN) configured on the SGSN or GGSN.
The following
filter keywords are valid with this command:
active-charging-service, apn, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-address, l3-tunnel-remote-address, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, msid, nat, nemo-only network-requested, network-type, pcf, pdsn-service, plmn-type, profile-id, profile-name, qci, rulename <rule_name>, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgsn-service, sgw-address, smgr-instance, without-dynamic-rule, without-override-control, tx-data, username, verbose, grep, more
asn-peer-address
ip_address
Displays information for subscribers on an ASN-GW trusted peer.
ip_address is
the IP address of the ASN-GW peer server expressed in IPv4 dotted-decimal
notation.
The following filter keywords are valid with this command:
asn-peer-address, asngw-service, bearer-establishment, bng-service, callid, card-num, configured-idle-timeout, connected-time, ebi, enodeb-address, fa, fa-service, firewall, full, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-address, l3-tunnel-remote-address, long-duration-time-left, mipv6ha-service, msid, nat, network-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgw-address, smgr-instance, tx-data, username, grep, more
asngw-only
service_name
Displays ASN-GW specific context information for the session.
The following filter keywords are valid with this command:
aaa-configuration, access-flows, active, activity, all, asn-peer-address, asngw-service, bearer-establishment, bng-service, callid, card-num, configured-idle-timeout, connected-time, counters, data-rate, dormant, ebi, enodeb-address, fa, fa-service, firewall, full, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-address, l3-tunnel-remote-address, long-duration-time-left, mipv6ha-service, msid, nat, network-type, policy, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgw-address, smgr-instance, subscription, summary, tft, tx-data, username, wf1, grep, more
asngw-service
service_name
Displays counters for subscribers accessing the ASN-GW service.
service_name
must be an existing service and be from 1 to 63 alphanumeric characters.
The following filter keywords are valid with this command:
asn-peer-address, asngw-service, bearer-establishment, bng-service, callid, card-num, configured-idle-timeout, connected-time, ebi, enodeb-address, fa, fa-service, firewall, full, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-address, l3-tunnel-remote-address, long-duration-time-left, mipv6ha-service, msid, nat, network-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgw-address, smgr-instance, tx-data, username, grep, more
asnpc-service
service_name
Displays counters for subscribers accessing the ASN Paging
Controller and Location Registry service.
service_name
must be an existing Access Service Network Paging Controller (ASN PC) service
and be from 1 to 63 alphanumeric characters.
The following filter keywords are valid with this command:
all, counters all, full, summary, grep, more
bandwidth-policy
policy_name
Show information
for subscribers associated with the specified Active Charging bandwidth policy.
Must be followed by the name of an existing bandwidth policy specified as an
alphanumeric string of 1 trough 63 characters.
The following
filter keywords are valid with this command:
access-type, active-charging-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, configured-idle-timeout, connected-time, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, firewall, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, hnbgw-service, hsgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lma-service, long-duration-time-left, mag-service, mipv6ha-service, msid, nat, network-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, security-type, session-time-left, sgw-address, smgr-instance, tx-data, ue-type, username, grep, more
bearer-establishment { direct-tunnel | normal | pending
}
Selects Bearer
Establishment type defined by the specified filter keywords.
-
direct-tunnel : Select subscribers having direct
tunnel established with the Radio Network Controller (RNC).
-
normal :
Select subscribers having bearer established with SGSN.
-
pending :
Select subscribers for whom bearer is not fully established.
The following
filter keywords are valid with this command:
apn, asn-peer-address, asngw-service, asnpc-service, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, css-delivery-sequence, css-service, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-udp-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdg-service, pdif-service, pdsn-service, pdsnclosedrp-service, pgw-address, plmn-type, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tx-data, username, grep, more
bng-service
srvc_name
Displays current
configuration the specified Broadband Network Gateway (BNG) service. The
following filter keywords are valid with this command:
active, all, apn, asn-peer-address, asngw-service, asnpc-service, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, pcf, pdg-service, pdif-service, pdsn-service, pdsnclosedrp-service, pgw-address, plmn-type, profile-id, profile-name, qci, rx-data, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tpo, tx-data, username, grep, more
callid
id
Displays
subscriber information for the call ID specified as an 8-byte hexadecimal
number.
The following
filter keywords are valid with this command:
adc, apn, asn-peer-address, asngw-service, asnpc-service, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, css-delivery-sequence, css-service, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-udp-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdg-service, pdif-service, pdsn-service, pdsnclosedrp-service, pgw-address, plmn-type, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tx-data, username, grep, more
card-num
card_num
The slot number of
the processing card by which the subscriber session is processed. The slot
number is an integer from 1 through 7 and 10 through 16 on the ASR 5000, or 1
through 4 and 7 through 10 on the ASR 5500.
The following
filter keywords are valid with this command:
apn, asn-peer-address, asngw-service, asnpc-service, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, cpu-num, css-delivery-sequence, css-service, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-udp-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdg-service, pdif-service, pdsn-service, pdsnclosedrp-service, pgw-address, plmn-type, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tx-data, username, grep, more
cbb-policy
policy_name
Show information
for subscribers associated with the specified Active Charging Content Based
Billing (CBB) policy. Must be followed by the name of an existing Active
Charging CBB policy specified as an alphanumeric string of 1 trough 63
characters.
The following
filter keywords are valid with this command:
active, active-charging -service, all, apn, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, hnbgw-only, hsgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-address, l3-tunnel-remote-address, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-udp-tunnel-only, mipv6ha-service, msid, nemo-only network-requested, network-type, pcf, pdsn-service, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgsn-service, tx-data, username, verbose, grep, more
ccoa-only
Displays current
configuration for all MIP-HA subscribers that registered with a collocated COA
only. The following filter keywords are valid with this command:
access-type, active-charging-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, configured-idle-timeout, connected-time, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, firewall, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, hnbgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, mipv6ha-service, msid, nat, network-type, pcc-service, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, smgr-instance, tpo, tx-data, username, grep, more
configuration { all | username
name
}
Displays current
configuration for all subscribers or a specified subscriber.
configured-idle-timeout [ < | > | greater-than | less-than
]
value
Shows the idle
timeout that is configured for the specified subscriber. A value of 0 (zero)
indicates that the subscribers idle timeout is disabled.
-
< : Filters
output so that only information less than the specified value is displayed.
-
> : Filters
output so that only information greater than the specified value is displayed.
-
greater-than :
Filters output so that only information greater than the specified value is
displayed.
-
less-than :
Filters output so that only information less than the specified value is
displayed.
-
value : Used
in conjunction with <, >, greater-than, less-than, If no other filtering
options are specified only output matching
value is
displayed. If
value is not
specified all data is displayed.
value must be
an integer from 0 through 4294967295.
congestion_mgmt { not-required | required
}
Shows the current
subscribers for which congestion management is
not-required
or
required.
The following filter keywords are valid with this command:
active-charging-service, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, configured-idle-timeout, congestion_mgmt, connected-time, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, hnbgw-service, henbgw-access-service, hsgw-service, idle-time, ims-auth-service, imsi, interface-type, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mipv6ha-service, mme-address, mme-service, msid, nat, network-type, pcp, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, saegw-service, session-time-left, sgw-address, sgw-service, smgr-instance, tpo, tx-data, username, wsg-service
connected-time [
< |
> |
greater-than
|
less-than ]
value
Shows how long the
subscriber has been connected.
-
< : Filters
output so that only information less than the specified value is displayed.
-
< : Filters
output so that only information less than the specified value is displayed.
-
> : Filters
output so that only information greater than the specified value is displayed.
-
greater-than :
Filters output so that only information greater than the specified value is
displayed.
-
less-than :
Filters output so that only information less than the specified value is
displayed.
-
value : Used
in conjunction with <, >, greater-than, less-than, If no other filtering
options are specified only output matching
value is
displayed. If
value is not
specified all data is displayed.
value must be
an integer from 0 through 4294967295.
counters
Shows the counters
associated with the subscriber. The following filter keywords are valid with
this command:
access-type, active, active-charging-service, all, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, dns-proxy, domain, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hnbgw-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pdsnclosedrp-service, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tpo, tx-data, ue-type, username, grep, more
css-delivery-sequence
Important |
This is a
restricted keyword. In
StarOS 9.0 and later, this keyword is obsoleted.
|
css-service
csssvc_name
Important |
This is a
restricted keyword. In
StarOS 9.0 and later releases, this keyword is obsolete.
|
data-rate
Displays
subscriber throughput data.
This keyword is
best used for individual subscriber output.
The following
filter keywords are valid with this command:
access-type, active, active-charging-service, all, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, graph, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, high, hnbgw-service, hsgw-only, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, pv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, low, mag-service, mipv6ha-service, mme-address, mme-service, msid, msisdn, network-requested, network-type, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pdsnclosedrp-service, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, summary, tpo, tx-data, ue-type, username, verbose, grep, more
debug-info {
callid
id |
msid
id |
username
name
}
Displays internal
call troubleshooting information for subscriber sessions defined by the
specified keywords.
-
callid
id : Displays
subscriber information for the call specified by
id . The call
ID must be specified as an 8-digit hexadecimal number.
-
msid
id : Displays
information for the mobile user identified by
id .
id must be
from 7 to 16 digits specified as an IMSI, MIN, or RMI. Wildcard characters $
and * are allowed. The * wildcard matches multiple characters and the $
wildcard matches a single character. If you do not want the wildcard characters
interpreted as a wildcard enclose them in single quotes ( ' ). For example;
'$'.
-
username
name :
Displays information for connections for the subscriber identified by
name . The
user must have been previously configured.
name must be
a sequence of characters and/or wildcard characters ('$' and '*') from 1 to 127
characters. The * wildcard matches multiple characters and the $ wildcard
matches a single character. If you do not want the wildcard characters
interpreted as wildcard enclose them in single quotes ( '). For example; '$'.
dhcp-server
ipv4_address
Displays
subscribers based on a specific DHCP server where their IP address was
allocated. Must be followed by IP address of the server, using IPv4
dotted-decimal notation.
The following
filter keywords are valid with this command:
apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, long-duration-time-left, msid, msisdn, nat, nemo-only, network-requested, pcf, pdsn-service, pdsnclosedrp-service, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, session-time-left, sgsn-address, sgsn-service, smgr-instance, tpo, tx-data, username, grep, more
domain
name
Displays all
subscribers with an Address-of-Record (AoR) from the specified domain.
name is an
alphanumeric string of 1 through 79 characters.
The following
filter keywords are valid with this command:
access-type, active-charging-service, all, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, configured-idle-timeout, connected-time, dhcp-server, domain, ebi, enodeb-address, fa, firewall, fw-and-nat, ggsn-service, graph, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, hnbgw-service, hsgw-only, hsgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, mipv6ha-service, msid, network-type, pcc-service, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgw-address, smgr-instance, summary, tpo, tx-data, ue-type, username, grep, more
dormant
number
Displays all
dormant subscribers, those registered but not transmitting/receiving data.
The following
filter keywords are valid with this command:
access-type, active-charging-service, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hnbgw-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-udp-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pdsnclosedrp-service, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tpo, tx-data, ue-type, username, grep, more
ebi
number
Displays
subscribers based on an EPS bearer identity.
number
specifies the EBI number and must be an integer value from 5 to 15.
The following
filter keywords are valid with this command:
access-type, active-charging-service, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, ebi, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hnbgw-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgw-address, sgw-service, smgr-instance, tx-data, ue-type, username, grep, more
enodeb-address ip_address
Displays
subscribers based on the eNodeB to which they are attached.
ip_address
must be a valid IP address of an existing eNodeB specified in IPv4
dotted-decimal or IPv6 colon-separated-hexadecimal notation.
The following
filter keywords are valid with this command:
access-type, active-charging-service, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hnbgw-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgw-address, sgw-service, smgr-instance, tx-data, ue-type, username, grep, more
epdg-address
ipv4_ipv6_address
Displays
subscribers connected to the specified ePDG peer specified in IPv4
dotted-decimal or IPv6 colon-separated-hexadecimal notation.
The following
filter keywords are valid with this command:
apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, idle-time, imei, ims-auth-service, imsi, interface-type, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tpo, tx-data, username, wsg-service, grep, more
fa
ipv4_address
Displays
subscribers for a specified Peer Foreign Agent. Must be followed by the IP
address of a Remote FA, in IPv4 dotted-decimal notation.
The following
filter keywords are valid with this command:
access-type, active-charging-service, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hnbgw-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pdsnclosedrp-service, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tpo, tx-data, ue-type, username, grep, more
epdg-only
Displays epdg-specific context information for the session.
The following filter keywords are valid with this command:
all, callid, card-num, configured-idle-timeout, connected-time, counters, data-rate, full, gtp-version, gtpu-bind-address, gtpu-service, idle-time, ip-address, ipv6-prefix, long-duration-time-left, network-type, qci, rx-data, session-time-left, smgr-instance, summary, tft, tx-data, username, grep, more
epdg-service
srvc_name
Displays subscribers for a specified Evolved Packet Data Gateway
service. Must be followed by ePDG service name expressed as an alphanumerical
string of 1 through 63 characters.
The following filter keywords are valid with this command:
all, callid, card-num, configured-idle-timeout, connected-time, counters, data-rate, epdg-address, epdg-service, full, gtp-version, gtpu-bind-address, gtpu-service, idle-time, ip-address, ipv6-prefix, long-duration-time-left, network-type, qci, rx-data, session-time-left, smgr-instance, summary, tft, tx-data, username, grep, more
fa-only
Displays FA-specific context information for the session.
The following filter keywords are valid with this command:
aaa-configuration, access-flows, active, activity, all, asn-peer-address, asngw-service, asnpc-service, bearer-establishment, callid, card-num, configured-idle-timeout, connected-time, counters, data-rate, dhcp-server, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, full, fw-and-nat, ggsn-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, long-duration-time-left, mag-service, mip-udp-tunnel-only, mipv6ha-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdif-service, pdsn-service, pgw-address, plmn-type, policy, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgw-address, sgw-service, smgr-instance, subscription, summary, tft, tx-data, username, wf1, grep, more
fa-service
srvc_name
Displays subscribers for a specified Foreign Agent service. Must
be followed by FA service name expressed as an alphanumerical string of 1
through 63 characters.
The following filter keywords are valid with this command:
aaa-configuration, access-flows, active, activity, all, asn-peer-address, asngw-service, asnpc-service, bearer-establishment, bng-service, callid, card-num, ccoa-only, configuration, configured-idle-timeout, connected-time, counters, data-rate, debug-info, dhcp-server, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-only, fa-service, firewall, full, fw-and-nat, ggsn-only, ggsn-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-only, lac-service, lns, lns-only, long-duration-time-left, mag-service, mip-udp-tunnel-only, mipv6ha-only, mipv6ha-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdif-service, pdsn-service, pgw-address, plmn-type, policy, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, sgw-service, smgr-instance, subscription, summary, tft, tx-data, username, wf1, grep, more
firewall { not-required | required }
Displays information for subscribers based on whether or not
firewall processing is required.
The following
filter keywords are valid with this command:
apn, asn-peer-address, asngw-service, asnpc-service, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv4, ipv6, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdg-service, pdif-service, pdsn-service, pdsnclosedrp-service, pgw-address, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tpo, tx-data, username, grep, more
fng-only
Displays Femto Network Gateway (FNG) context information for the
session.
The following filter keywords are valid with this command:
aaa-configuration, access-flows, active, activity, all, bearer-establishment, bng-service, callid, card-num, configured-idle-timeout, connected-time, counters, data-rate, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fng-service, full, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, henbgw-access-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, mipv6ha-service, msid, nat, network-type, pdif-service, policy, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgw-address, smgr-instance, subscription, summary, tft, tx-data, username, wf1, grep, more
fng-service
srvc_name
Displays information for subscribers accessing the specified FNG
service.
service_name
must be an existing service expressed as an alphanumeric string of 1 through 63
characters.
The following filter keywords are valid with this command:
bearer-establishment, bng-service, callid, card-num, configured-idle-timeout, connected-time, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fng-service, full, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, henbgw-access-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, mipv6ha-service, msid, nat, network-type, pdif-service, profile-id, profile-name, qci, rx-data, session-time-left, sgw-address, smgr-instance, subscription, summary, tft, tx-data, username, grep, more
full
Shows all
available subscriber information. The following filter keywords are valid with
this command:
access-type, active, active-charging-service, all, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hnbgw-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, long-duration-time-left, mag-service, mip-udp-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, network-requested, network-type, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pdsnclosedrp-service, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s1-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tpo, tx-data, ue-type, username, grep, more
fw-and-nat policy
fw_nat_policy
Important |
This option is
customer-specific and is only available in StarOS 8.1.
|
Displays information for subscribers using an existing
Firewall-and-NAT policy specified as an alphanumeric string of 1 through 15
characters.
ggsn-only
Displays only GGSN-specific subscriber context information.
The following filter keywords are valid with this command:
aaa-configuration, access-flows, active, activity, all, apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, counters, data-rate, dhcp-server, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, full, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-only, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdsn-service, plmn-type, policy, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, smgr-instance, subscription, summary, tft, tx-data, username, wf1, grep, more
ggsn-service
srvc_name
Displays only subscribers for a specified GGSN service. Must be
followed by the GGSN service name expressed as an alphanumeric string of 1
through 63 characters.
The following filter keywords are valid with this command:
apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdsn-service, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, smgr-instance, tx-data, username, grep, more
gsm-traffic-class { background | conversational | interactive
}
Displays subscribers associate with the specified 3GPP QoS
traffic class.
The following
filter keywords are valid with this keyword:
apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdsn-service, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, smgr-instance, tx-data, username, grep, more
gprs-only
This keyword is specific to the SGSN and only displays 2G SGSN
subscriber information.
The following
filter keywords are valid with this keyword:
aaa-configuration, active, active-charging-service, activity, all, apn, callid, card-num, configured-idle-timeout, connected-time, counters, data-rate, full, ggsn-address, gprs-service, gsm-traffic-class, idle-time, imsi, msid, msisdn, partial, plmn-type, profile-name, rx-data, session-time-left, summary, tx-data, wide-format, grep, more
gprs-service
srvc_name
Enter the name of
the configured 2G GPRS service to display subscriber information specific to
the named GPRS service for the SGSN.
srvc_name
must be an alphanumeric string of 1 through 63 characters that identifies a
configured GPRS service.
The following
filter keywords are valid with this command:
apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdsn-service, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, smgr-instance, tx-data, username, grep, more
gsm-traffic-class { background | conversational | interactive |
streaming }
Displays
information for subscriber traffic that matches the specified 3GPP traffic
class.
-
background :
3GPP QoS background class.
-
conversational : 3GPP QoS conversational class.
-
interactive :
3GPP QoS interactive class. Must be followed by a traffic priority.
-
streaming :
3GPP QoS streaming class.
The following
filter keywords are valid with this command:
apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ims-auth-service, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdsn-service, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgsn-service, sgw-address, smgr-instance, tx-data, username, grep, more
gtp-version { 0 | 1 }
Displays the
specific GTP version number. Must be followed by one of the supported GTP
versions (0 or 1).
The following
filter keywords are valid with this command:
apn, bearer-establishment, bng-service, callid, card-num, configured-idle-timeout, connected-time, ebi, enodeb-address, epdg-address, epdg-service, fa, firewall, fw-and-nat, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, henbgw-access-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, mag-service, mipv6ha-service, msid, msisdn, nat, network-type, nri, nsei, pdg-service, pdif-service, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-service, sgw-address, smgr-instance, tx-data, username, grep, more
gtpu-bind-address
ipv4_address
Displays the
subscribers associated with the specified GTPU service bind address. Must be
followed by an IPv4 address in dotted decimal notation.
The following
filter keywords are valid with this command:
access-type, active-charging-service, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hnbgw-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-udp-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgw-address, sgw-service, smgr-instance, tx-data, ue-type, username, grep, more
gtpu-service
svc_name
Displays the
subscribers associated with an existing GTPU service specified as an
alphanumeric string of 1 through 63 characters.
The following
filter keywords are valid with this command:
access-type, active-charging-service, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hnbgw-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-udp-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgw-address, sgw-service, smgr-instance, tx-data, ue-type, username, grep, more
ha
ipv4_address
Displays the
subscribers associated with the specified Peer Home Agent. Must be followed by
the IP address of a Remote HA in IPv4 dotted-decimal notation.
The following
filter keywords are valid with this command:
access-type, active-charging-service, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hnbgw-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-services, mip-udp-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgw-address, sgw-service, smgr-instance, tx-data, ue-type, username, grep, more
ha-ipsec-only
Displays MIPHA
subscribers with subscriber IPSec tunnel only.
The following
filter keywords are valid with this command:
apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdsn-service, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, smgr-instance, tx-data, username, grep, more
ha-service
svc_name
Displays the
subscribers associated with an existing Home Agent service specified as an
alphanumeric string of 1 through 63 characters.
The following
filter keywords are valid with this command:
apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdsn-service, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, smgr-instance, tx-data, username, grep, more
henbgw-access-service svc_name
Displays specific
configured HENBGW access service information. This must be followed by HENBGW
access service name.
The following
filters/keywords are valid with this command:
bearer-establishment, bng-service, callid, card-num, configured-idle-timeout, congestion_mgmt, connected-time, ebi, enodeb-address, epdg-address, fa, fa-service, firewall, fng-service, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, henbgw-access-service, hnbgw-service, idle-time, ims-auth-service, imsi, interface-type, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, mipv6ha-service, msid, nat, network-type, pcp, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, smgr-instance, tx-data, username, grep, more
henbgw-only
Displays specific
HENBGW information for the session.
The following
filters/keywords are valid with this command:
aaa-configuration, access-flows, active, activity, all, bearer-establishment, bng-service, callid, card-num, configured-idle-timeout, congestion_mgmt, connected-time, counters, data-rate, dormant, ebi, enodeb-address, epdg-address, fa, fa-service, firewall, fng-service, full, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, henbgw-access-service, hnbgw-service, idle-time, ims-auth-service, imsi, interface-type, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, mipv6ha-service, msid, nat, network-type, pcp, policy, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, smgr-instance, subscription, summary, tft, tx-data, username, wf1, grep, more
hnbgw-only
Displays HNB-GW
subscriber session information.
The following
filters/keywords are valid with this command:
aaa-configuration, access-flows, access-type, active, active-charging-service, activity, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, configured-idle-timeout, connected-time, counters, data-rate, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, firewall, full, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, henbgw-access-service, hnbgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, mipv6ha-service, msid, nat, network-type, pcc-service, policy, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, smgr-instance, subscription, summary, tpo, tx-data, ue-type, username, wf1, grep, more
hnbgw-service
svc_name
Displays
subscriber information based on the HNB-GW service name.
svc_name must
be an existing HNB-GW service expressed as an alphanumeric string of 1 through
63 characters.
The following
filters/keywords are valid with this command:
access-type, active-charging-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, configured-idle-timeout, connected-time, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, firewall, full, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, henbgw-access-service, hnbgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, mipv6ha-service, msid, nat, network-type, pcc-service, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, smgr-instance, tpo, tx-data, ue-type, username, grep, more
hsgw-only
Displays HSGW subscriber session information.
The following filters/keywords are valid with this command:
aaa-configuration, access-flows, active, active-charging-only, all, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, configured-idle-timeout, connected-time, counters, data-rate, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, firewall, full, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, hsgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, mag-service, mipv6ha-service, msid, nat, network-type, pgw-address, policy, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, session-time-left, sgw-address, smgr-instance, subscription, summary, tft, tx-data, username, wf1, grep, more
hsgw-service
svc_name :
Displays subscriber information based on the HSGW service name.
svc_name must
be an existing HSGW service expressed as an alphanumeric string of 1 through 63
characters.
hsgw-service
svc_name
Displays subscriber information based on the HSGW service name.
svc_name must
be an existing HSGW service expressed as an alphanumeric string of 1 through 63
characters.
The following
filters/keywords are valid with this command:
active-charging-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, configured-idle-timeout, connected-time, ebi, enodeb-address, epdg-address, epdg-service, fa, firewall, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, hsgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, mag-service, mipv6ha-service, msid, nat, network-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, session-time-left, sgw-address, smgr-instance, tx-data, username, grep, more
idle-time
Displays current
configuration for all subscribers within the specified idle-time interval.
-
< : Filters
output so that only information less than the specified value is displayed.
-
< : Filters
output so that only information less than the specified value is displayed.
-
> : Filters
output so that only information greater than the specified value is displayed.
-
greater-than :
Filters output so that only information greater than the specified value is
displayed.
-
less-than :
Filters output so that only information less than the specified value is
displayed.
-
value : Used
in conjunction with <, >, greater-than, less-than, If no other filtering
options are specified only output matching
value is
displayed. If
value is not
specified all data is displayed.
value must be
an integer from 0 through 4294967295.
The following
filter keywords are valid with this command:
epdg-address, epdg-service
imei
imei_number
Displays
subscribers having the specified International Mobile Equipment Identity
(IMEI/IMEISV) Number. Must be followed by IMEI number.
The following
filter keywords are valid with this command:
apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdsn-service, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, smgr-instance, tx-data, username, grep, more
ims_auth-service
svc_name
Displays subscriber information based on the IMS authentication
service name.
svc_name must
be an existing service expressed as an alphanumeric string of 1 through 63
characters.
The following
filters/keywords are valid with this command:
access-type, active-charging-service, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, gprs-service, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec, ha-service, henbgw-access-service, hnbgw-service, hsgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-up-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tpo, tx-data, ue-type, username, grep, more
imsi
imsi
Displays
information specific to one subscriber or group of subscribers. Enter 1 to 15
digits to identify a specific subscriber's IMSI (International Mobile
Subscriber Identity).
The following
filters/keywords are valid with this command:
access-type, active-charging-service, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hnbgw-service, hsgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-services, mip-up-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, nsapi, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tpo, tx-data, ue-type, username, grep, more
interface-type { S2aGTP | S2bGTP | S5S8GTP
}
Specifies
subscrber type as either
S2a (eHRPD),
S2b (ePDG)
or
S5/S8
(PMIPv6/GTP).
The following
filter keywords are valid with this command:
apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, congestion_mgmt, connected-time, dhcp-server, ebi, enodeb-address, epdg-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, idle-time, imei, ims-auth-service, imsi, interface-type, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pcp, pdsn-service, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, smgr-instance, tx-data, username, wsg-service, grep, more
ip-address
ipv4_address
Displays the
subscribers associated with the specified IPv4 address. Must be followed by the
IP address in IPv4 dotted-decimal notation.
The following
filter keywords are valid with this command:
access-type, active-charging-service, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hnbgw-service, hsgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-up-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, nsapi, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tpo, tx-data, ue-type, username, grep, more
ip-alloc-method {aaa-assigned | dhcp [ relay-agent |
proxy-client ] | dynamic-pool | l2tp-lns-assigned | mip-ha-assigned |
ms-provided-static | not-ms-provided-static | static pool
}
Displays the
specific IP Allocation Method. Must be followed by one of the IP Allocation
Methods:
-
aaa-assigned :
Selects subscribers whose IP addresses were assigned by AAA.
-
dhcp : Selects
subscribers whose IP addresses were assigned by DHCP.
-
dynamic-pool :
Selects subscribers whose IP addresses were assigned from a dynamic IP address
pool.
-
l2tp-lns-assigned : Selects subscribers whose IP
addresses were assigned by the Layer 2 Tunneling Protocol (LT2P) Network
Server.
-
mip-ha-assigned : Selects subscribers whose IP
addresses were assigned by the Mobile IP Home Agent.
-
ms-provided-static : Selects subscribers whose IP
addresses were provided by the Mobile Station.
-
not-ms-provided-static : Selects subscribers whose
IP addresses were not provided by the Mobile Station.
-
static-pool :
Selects subscribers whose IP addresses were assigned from a static IP address
pool.
The following
filter keywords are valid with this command:
access-type, active-charging-service, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hnbgw-service, hsgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-up-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, nsapi, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, relay-agent, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tpo, tx-data, ue-type, username, grep, more
ip-pool
ip_pool_name
Displays subscriber information based on the IP pool name.
ip_pool_name
must be an existing IP pool name expressed as an alphanumeric string of 1
through 31 characters.
The following
filter keywords are valid with this command:
access-type, active-charging-service, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, henbgw-access-service, hnbgw-service, hsgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-up-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, nsapi, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tpo, tx-data, ue-type, username, grep, more
ipcf-only
Displays Intelligent Policy Control Function (IPCF) subscriber
session information.
ipsg-only
Displays IP Services Gateway (IPSG) subscriber session
information.
The following
filter keywords are valid with this command:
epdg-address, epdg-service
ipv6-address
ipv6_address
Displays the
subscribers associated with the specified IPv6 address. Must be followed by the
IP address in IPv8 colon-separated-hexadecimal notation.
The following
filter keywords are valid with this command:
apn, asn-peer-address, asngw-service, asnpc-service, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-udp-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, sgw-service, smgr-instance, tx-data, username, grep, more
ipv6-prefix
ipv6_prefix
Displays the
subscribers associated with the specified IPv6 address prefix. Must be followed
by an IPv6 address prefix in the format xx:xx:xx::/len
The following
filter keywords are valid with this command:
access-type, active-charging-service, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, hnbgw-service, hsgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-up-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, nsapi, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tpo, tx-data, ue-type, username, grep, more
l3-tunnel-local-addr
ipv4_address
Displays subscriber information based on the layer 3 tunneling
interface. Must be followed by an IP address of the local interface, using IPv4
dotted-decimal notation.
The following
filter keywords are valid with this command:
access-type, active-charging-service, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, hnbgw-service, hsgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-up-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, nsapi, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tpo, tx-data, ue-type, username, grep, more
l3-tunnel-remote-addr
ipv4_address
Displays subscriber information based on the layer 3 tunneling
interface. Must be followed by an IP address of the remote interface, using
IPv4 dotted-decimal notation.
The following
filter keywords are valid with this command:
access-type, active-charging-service, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, hnbgw-service, hsgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-up-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, nsapi, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tpo, tx-data, ue-type, username, grep, more
lac
ipv4_address
Displays subscriber information based on the Peer L2TP Access
Concentrator (LAC). Must be followed by the IP address of a Remote LAC in IPv4
dotted-decimal notation.
The following
filter keywords are valid with this command:
apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdsn-service, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, smgr-instance, tx-data, username, grep, more
lac-only
Displays subscriber information based on the L2TP Access
Concentrator (LAC) context information for the session.
lac-service
svc_name
Displays subscriber information based on an existing LAC service
name expressed as an alphanumeric string of 1 through 63 characters.
The following
filter keywords are valid with this command:
apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, local-tunnel-id, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdsn-service, plmn-type, profile-id, profile-name, qci, remote-tunnel-id, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, smgr-instance, tx-data, username, grep, more
lma-only
Displays Local Mobility Anchor (LMA) specific context
information for the session.
lma-service
svc_name
Displays subscriber information based on the LMA service name.
svc_name must
be an existing LMA service expressed as an alphanumeric string of 1 through 63
characters.
lns
ipv4_address
Displays subscriber information based on the L2TP Network Server
(LNS)). Must be followed by the IP address of an LNS in IPv4 dotted-decimal
notation.
The following
filter keywords are valid with this command:
apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdsn-service, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, smgr-instance, tx-data, username, grep, more
lns-only
Displays LNS
specific information only.
lns-service
svc_name
Displays subscriber information based on an existing L2TP
Network Server (LNS) service name expressed as an alphanumeric string of 1
through 63 characters.
The following
filter keywords are valid with this command:
bearer-establishment, bng-service, callid, card-num, configured-idle-timeout, connected-time, ebi, enodeb-address, epdg-address, epdg-service, fa, firewall, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns-service, local-tunnel-id, long-duration-time-left,mipv6ha-service, msid, nat, network-type, profile-id, profile-name, qci, remote-tunnel-id, rx-data, s1u-state, s5-proto, session-time-left, sgw-address, smgr-instance, tx-data, username, grep, more
long-duration-time-left [ < | > | greater-than | less-than
]
value
Shows how much
time is left for the maximum duration of a specified subscriber session.
-
< : Filters
output so that only information less than the specified value is displayed.
-
> : Filters
output so that only information greater than the specified value is displayed.
-
greater-than :
Filters output so that only information greater than the specified value is
displayed.
-
less-than :
Filters output so that only information less than the specified value is
displayed.
-
value : Used
in conjunction with <, >, greater-than, less-than, If no other filtering
options are specified only output matching
value is
displayed. If
value is not
specified all data is displayed.
value must be
an integer from 0 through 4294967295.
mag-only
Displays Mobile
Access Gateway (MAG) subscriber session information.
mag-service
svc_name :
Displays subscriber information based on the Mobile Access Gateway (MAG)
service name.
svc_name must
be an existing MAG service expressed as an alphanumeric string of 1 through 63
characters.
mag-service
svc_name
Displays
subscriber information based on the Mobile Access Gateway (MAG) service name.
svc_name must
be an existing MAG service expressed as an alphanumeric string of 1 through 63
characters.
mip-udp-tunnel-only
Displays Mobile IP Home Agent (MIP-HA) subscriber information
for subscribers that negotiated MIP-UDP tunnels.
The following
filter keywords are valid with this command:
apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdsn-service, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, smgr-instance, tx-data, username, grep, more
mipv6ha-only
Displays MIP-HA-IPv6 context information for the session.
The following
filters/keywords are valid with this command:
aaa-configuration, access-flows, access-type, active, active-charging-service, activity, all, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, counters, data-rate, dhcp-server, domain, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, full, fw-and-nat, ggsn-address, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, hnbgw-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mipv6ha-service, mme-address, mme-service, msid, nat, network-requested, network-type, pcc-service, pcf, pdg-service, pdif-service, pgw-address, policy, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, subscription, summary, tft, tpo, tx-data, ue-type, username, wf1, grep, more
mipv6ha-service
svc_name
Displays subscriber information based on an existing MIP Home
Agent IPv6 service name expressed as an alphanumeric string of 1 through 63
characters.
The following
filter keywords are valid with this command:
access-type, active-charging-service, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, hnbgw-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-up-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tpo, tx-data, ue-type, username, grep, more
mme-address
Displays subscriber information based on the Mobility Management
Entity (MME) IP address.
ip_address
must be an existing MME IP address and be entered in IPv4 dotted-decimal
notation or IPv6 colon-separated-hexadecimal notation.
The following
filter keywords are valid with this command:
bearer-establishment, bng-service, callid, card-num, configured-idle-timeout, connected-time, ebi, enodeb-address, epdg-address, epdg-service, fa, firewall, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, network-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgw-address, smgr-instance, tx-data, username, grep, more
mme-only
Displays MME subscriber session information.
mme-service
svc_name :
Displays subscriber information based on the MME service name.
svc_name must
be an existing MME service expressed as an alphanumeric string of 1 through 63
characters.
mme-address
ip_address :
Displays subscriber information based on the MMM IP address.
ip_address
must be an existing MME IP address entered in IPv4 dotted-decimal notation or
IPv6 colon-separated-hexadecimal notation.
The following
filter keywords are valid with this command:
bearer-establishment, bng-service, callid, card-num, configured-idle-timeout, connected-time, ebi, enodeb-address, epdg-address, epdg-service, fa, firewall, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, network-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgw-address, smgr-instance, tx-data, username, grep, more
mseg-only
Important |
This keyword is
not supported in this release.
|
mseg-service
mseg_service_name
Important |
This keyword is
not supported in this release.
|
msid
msid
For this
SGSN-specific keyword, enter the MSID (Mobile Station IDentifier) to display
information specific to one subscriber's equipment by entering the MSID.
The following
filter keywords are valid with this command:
apn, asn-peer-address, asngw-service, asnpc-service, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-udp-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, sgw-service, smgr-instance, tx-data, username, grep, more
msisdn
msisdn
For this
SGSN-specific keyword, enter the MSISDN (Mobile Station ISDN number - unique
SIM phone number) to display information specific to one subscriber's equipment
by entering the MSISDN.
The following
filter keywords are valid with this command:
apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdsn-service, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, smgr-instance, tx-data, username, grep, more
nat { not-required | required }
Displays information for subscribers based on whether or not
Network Address Translation (NAT) processing is required.
The following
filter keywords are valid with this command:
access-type, active-charging-service, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, hnbgw-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-up-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, multiple-ips-per-nat-realm, nat, nat-ip, nat-realm, nemo-only, network-requested, network-type, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tpo, tx-data, ue-type, usage-time, username, grep, more
nemo-only
Displays information on MIP-HA subscribers that are mobile
routers (Network Mobility).
The following
filter keywords are valid with this command:
apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdsn-service, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, smgr-instance, tx-data, username, grep, more
network-requested
Selects the currently active subscribers whose sessions were
initiated by a GGSN network requested to create a PDP context.
The following
filter keywords are valid with this command:
access-type, active-charging-service, apn, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, hnbgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, long-duration-time-left, mip-up-tunnel-only, mipv6ha-service, msid, msisdn, nat, nemo-only, network-requested, network-type, nsapi, pcc-service, pcf, pdsn-service, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, smgr-instance, tpo, tx-data, ue-type, username, grep, more
network-type { gre | ipip | ipsec | ipv4 | ipv4-pmipv6 | ipv4v6
| ipv4v6-pmipv6 | ipv6 | ipv6-pmipv6 | l2tp | mobile-ip | proxy-mobile-ip
}
Selects the currently active subscribers based on network
service access type.
- gre : Generic Routing Encapsulation
-
ipip :
IP-in-IP
-
ipsec : IPSec
-
ipv4 : IPv4
only
-
ipv4-pmipv6 :
IPv4 and/or Proxy Mobile IPv6 (PMIP)
-
ipv4v6 : IPv4
and/or IPv6
-
ipv4v6-pmipv6 : IPv4, IPv6 and/or Proxy Mobile IPv6
-
ipv6 : IPv6
only
-
ipv6-pmipv6 :
IPv6 and/or Proxy Mobile IPv6 (PMIP)
-
l2tp : Layer 2
Tunneling Protocol
-
mobile-ip :
Mobile IP (MIP)
-
proxy-modile-ip : Proxy Mobile IPv6 (PMIP)
The following
filter keywords are valid with this command:
apn, asn-peer-address, asngw-service, asnpc-service, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-udp-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, sgw-service, smgr-instance, tx-data, username, grep, more
pcc-service
name
Displays statistics for users associated with an existing Policy
and Charging Control (PCC) service name expressed as an alphanumeric string of
1 through 63 characters.
pcf [
< | > | less-than | greater-than]
ipv4_address
[
<
| > | less-than |
greater-than ]
ipv4_address
]
Displays
information for subscribers connected via the packet control function (PCF)
with a specific or range of IP addresses. The address must be specified using
IPv4 dotted-decimal notation.
-
< : Filters
output so that only information less than the specified IPv4 address value is
displayed.
-
> : Filters
output so that only information greater than the specified IPv4 address value
is displayed.
-
less-than: Filters
output so that only information less than the specified IPv4 address value is
displayed.
-
greater-than: Filters
output so that only information greater than the specified IPv4 address value
is displayed.
Note: It is
possible to define a limited range of IP addresses by using the less-than and
greater-than options to define minimum and maximum values.
The following
filter keywords are valid with this command:
<, apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, less than, lns, lns-service, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdsn-service, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, smgr-instance, tx-data, username, grep, more
pdg-only
Displays a summary of PDG subscriber statistics.
The following
filters/keywords are valid with this command:
aaa-configuration, access-flows, active, activity, all, apn, bearer-establishment, bng-service, callid, card-num, configured-idle-timeout, connected-time, counters, data-rate, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, firewall, full, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, mipv6ha-service, msid, nat, network-type, pdg-service, policy, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgw-address, smgr-instance, subscription, summary, tft, tx-data, username, wf1, grep, more
pdg-service
name
Displays statistics for users associated with an existing Packet
Data Gateway (PDG) service name expressed as an alphanumeric string of 1
through 63 characters.
The following
filters/keywords are valid with this command:
bearer-establishment, bng-service, callid, card-num, configured-idle-timeout, connected-time, ebi, enodeb-address, epdg-address, epdg-service, fa, firewall, fng-service, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, mipv6ha-service, msid, nat, network-type, pdg-service, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgw-address, smgr-instance, tx-data, username, grep, more
pdif-only
Displays a summary of Packet Data Interworking Function (PDIF)
subscriber statistics.
The following
filters/keywords are valid with this command:
aaa-configuration, access-flows, active, activity, all, apn, bearer-establishment, bng-service, callid, card-num, configured-idle-timeout, connected-time, counters, data-rate, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fng-service, full, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, mipv6ha-service, msid, nat, network-type, pdif-service, policy, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgw-address, smgr-instance, subscription, summary, tft, tx-data, username, wf1, grep, more
pdif-service
name
Displays connection statistics for users associated with a
specific PDIF service name.
The following
filters/keywords are valid with this command:
bearer-establishment, bng-service, callid, card-num, configured-idle-timeout, connected-time, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fng-service, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, mipv6ha-service, msid, nat, network-type, pdif-service, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgw-address, smgr-instance, tx-data, username, grep, more
pdsn-only
Displays a summary of Packet Data Serving Node (PDSN) subscriber
statistics.
The following
filters/keywords are valid with this command:
aaa-configuration, access-flows, active, activity, all, apn, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, counters, data-rate, dhcp-server, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, full, fw-and-nat, ggsn-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, msid, nat, nemo-only, network-requested, network-type, pcf, pdsn-service, plmn-type, policy, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgsn-service, sgw-address, smgr-instance, subscription, summary, tft, tpo, tx-data, username, wf1, grep, more
pdsn-service
name
Displays statistics for users associated with an existing PDSN
service name expressed as an alphanumeric string of 1 through 63 characters.
The following
filter keywords are valid with this command:
apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lns, lns-service, long-duration-time-left, mag-address, mip-udp-tunnel-only, mipv6ha-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdsn-service, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, smgr-instance, tx-data, username, grep, more
pgw-address
ip_address
Displays information about the subscribers connected to the
specified P-GW.
ip_address
must be specified by its IP address using dotted-decimal notation for IPv4 or
colon separated notation for IPv6.
The following filters/keywords are valid with this command:
active-charging-service, apn, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, configured-idle-timeout, connected-time, ebi, enodeb-address, epdg-address, epdg-service, fa, firewall fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac-service, lma-service, lns, long-duration-time-left, mag-service, mipv6ha-service, msid, nat, network-type, pgw-address, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, saegw-service, session-time-left, sgw-address, sgw-service, smgr-instance, tx-data, username
pgw-only
Displays PDN-Gateway (P-GW) subscriber session information.
The following filters/keywords are valid with this command:
all, apn, callid, card-num, ebi, epdg-address , full, imsi, interface-type, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, network-type, pgw-service, plmn-type, profile-name, qci, sgw-address, smgr-instance, summary
-
epdg-address
ip_address :
Displays subscriber information based on the ePDG IP address.
ip_address
must be an existing ePDG IP address.
-
interface-type : Interface type of subscriber.
S2aGTP :
Interface type S2a GTP.
S2bGTP : Interface type S2b GTP.
S5S8GTP : Interface type S5/S8 GTP.
-
pgw-service
svc_name :
Displays subscriber information based on the P-GW service name.
svc_name must
be an existing P-GW service expressed as an alphanumeric string of 1 through 63
characters.
-
qci
number :
Displays subscriber session information based on the QoS Class Identifier (QCI)
value assigned to the subscriber.
number must
be an integer value from 0 to 9.
-
sgw-address
ip_address :
Displays subscriber information based on the S-GW IP address.
ip_address
must be an existing S-GW IP address.
plmn-type [ home | roaming | visiting }
Displays
subscriber information based on the type of Public Land Mobile Network (PLMN).
-
home : For
GGSN/PGW, shows all the subscribers of charging type HOME.
-
roaming : For
GGSN/PGW, shows all the subscribers of charging type ROAMING.
-
visiting : For
GGSN/PGW, shows all the subscribers of charging type VISITING.
The following
filter keywords are valid with this command:
apn, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mip-udp-tunnel-only, mipv6ha-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdsn-service, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, smgr-instance, tx-data, username, grep, more
policy
Displays the
current policies associated with the subscriber session.
The following
filter keywords are valid with this command:
access-type, active-charging-service, all, apn, asn-peer-address, asngw-service, asnpc-service, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, domain, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, hnbgw-service, hsgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-up-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, nsapi, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgsn-service, sgw-address, sgw-service, smgr-instance, tpo, tx-data, ue-type, username, grep, more
profile-id
id_number
Displays
subscriber session information based on the profile-id granted for the flow.
id_number
must be an integer from 0 to 4294967295.
profile-name
name
Displays
subscriber session information based on an existing policy profile name
expressed as an alphanumeric string of 1 through 63 characters.
qci
number
Displays
subscriber session information based on the QoS Class Identifier (QCI) value
assigned to the subscriber.
number must
be an integer value from 0 to 9.
rulebase
name
Displays
subscriber session information based on the named Active Charging System
rulebase.
name must be
an alphanumeric string of 1 through 63 characters.
rulename rule_name
Displays subscribers associated with the specific charging rule name.
The
rule_name options are: predefined, static, and dynamic rules..
rx-data [ < | > | greater-than | less-than ]
value
The number of
bytes received by the specified subscriber.
-
< : Filters
output so that only information less than the specified value is displayed.
-
> : Filters
output so that only information greater than the specified value is displayed.
-
greater-than :
Filters output so that only information greater than the specified value is
displayed.
-
less-than :
Filters output so that only information less than the specified value is
displayed.
-
value : Used
in conjunction with <, >, greater-than, less-than, If no other filtering
options are specified only output matching
value is
displayed. If
value is not
specified all data is displayed.
value must be
an integer from 0 through 18446744073709551615.
s1u-state { active | idle | idle-active }
Displays session information based on the subscriber's S1-U
state. The S1-U interface is the interface from the eNodeB to the S-GW.
-
active :
Displays session information for subscribers with an S1-U state set to active.
-
idle :
Displays session information for subscribers with an S1-U state set to idle.
-
idle-active :
Displays session information for subscribers with an S1-U state set to
idle-active.
s5-proto { gtp | pmip }
Displays
subscriber session information based on the S5 interface protocol used. This
interface provides user plane tunneling and tunnel management between S-GW and
P-GW. Choose either GPRS Tunneling Protocol (GTP) or Proxy Mobile IPv6 (PMIP).
saegw-only
Displays System Architecture Evolution Gateway (SAEGW)
subscriber session information.
The following filters/keywords are valid with this command:
aaa-configuration, access-flows, active, active-charging-service, activity, all, apn, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, co-located, configured-idle-timeout, connected-time, counters, data-rate, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, firewall, full, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac-service, lma-service, lns, long-duration-time-left, mipv6ha-service, msid, nat, network-type, pgw-address, pgw-anchored, plmn-type, policy, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, saegw-service, session-time-left, sgw-address, sgw-anchored, smgr-instance, subscription, summary, tft, tx-data, username, wf1
-
co-located : Shows only co-located subscribers
which have both S-GW and P-GW functions.
-
pgw-anchored : Shows only PGW-anchored subscribers.
-
saegw-service
svc_name :
Displays subscriber information based on the SAEGW service name.
svc_name must
be an existing SAEGW service expressed as an alphanumeric string of 1 through
63 characters.
-
sgw-anchored
: Shows only SGW-anchored subscribers.
saegw-service
svc_name
Displays subscriber information based on the SAEGW service name.
svc_name must
be an existing SAEGW service expressed as an alphanumeric string of 1 through
63 characters.
The following filters/keywords are valid with this command:
active-charging-service, apn, bandwidth-policy, bearer-establishment, bng-service, callid, card-num, cbb-policy, configured-idle-timeout, connected-time, ebi, enodeb-address, epdg-address, epdg-service, fa, firewall, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac-service, lma-service, lns, long-duration-time-left, mipv6ha-service, msid, nat, network-type, pgw-address, plmn-type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-proto, saegw-service, session-time-left, sgw-address, smgr-instance, tx-data, username
security-type { ipsec | tls }
Displays subscriber information based on the specified type of
security.
- ipsec : IPSec
- tls : Transport Layer Security
session-time-left [ < | > | greather-than | less ]
value
How much session
time is left for the specified subscriber.
-
< : Filters
output so that only information less than the specified value is displayed.
-
> : Filters
output so that only information greater than the specified value is displayed.
-
greater-than :
Filters output so that only information greater than the specified value is
displayed.
-
less-than :
Filters output so that only information less than the specified value is
displayed.
-
value : Used
in conjunction with <, >, greater-than, less-than, If no other filtering
options are specified only output matching
value is
displayed. If
value is not
specified all data is displayed.
value must be
an integer from 0 through 4294967295.
sgsn-address
ipv4_address
This SGSN-only keyword displays only subscriber context
information for the specified interface. Must be followed by the IP address of
the interface, using IPv4 dotted-decimal notation.
The following
filter keywords are valid with this command:
apn, callid, card-num, connected-time, idle-time, gprs-service, gsm-traffic-class, gtp-version, imsi, msid, msisdn, nri, nsei, sgsn-service, smgr-instance
sgsn-only
This SGSN-only keyword displays only 3G SGSN-specific subscriber
context information.
The following
filter keywords are valid with this command:
aaa-configuration, active, active-charging-service, activity, all, apn, callid, card-num, configured-idle-timeout, connected-time, counters, data-rate, fa, full, ggsn-address, gsm-traffic-class, idle-time, imei, imsi, msid, partial, plmn-type, profile-name, rnc, rx-data, session-time-left, sgsn-service, summary, tx-data, wide-format, grep, more
sgsn-service
service_name
For this SGSN-only
keyword, enter the name of the configured 3G SGSN service to display subscriber
information specific to the named SGSN service.
The following
filter keywords are valid with this command:
apn, bearer-establishment, bng-service, callid, card-num, configured-idle-timeout, connected-time, ebi, enodeb-address, epdg-address, epdg-service, fa, firewall, fw-and-nat, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, idle-time, imei, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, mipv6ha-service, msid, msisdn, nat, network-type, nri, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-service, sgw-address, smgr-instance, tx-data, username, grep, more
sgw-address
ip_address
For this MME-only keyword, enter the IP address of the peer S-GW
to display information about the subscribers connected to the specified S-GW.
ip_address
must be specified by its IP address using IPv4 dotted-decimal or IPv6
colon-separated-hexadecimal notation.
sgw-only
Displays S-GW subscriber session information.
The following filters/keywords are valid with this command:
all, full, summary
-
sgw-service
svc_name :
Displays subscriber information based on en existing S-GW service specified as
an alphanumeric string of 1 through 63 characters.
-
pgw-address
ip_address :
Displays subscriber information based on an existing P-GW specified by its IP
address in IPv4 dotted-decimal notation.
sgw-service
svc_name
Displays subscriber information based on an existing S-GW
service specified as an alphanumeric string of 1 through 63 characters.
The following
filter keywords are valid with this command:
epdg-address, epdg-service,
smgr-instance
instance_id
Displays
subscription information associated with the Session Manager identifier express
as an integer from 1 through 4294967295.
The following
filter keywords are valid with this command:
epdg-address, epdg-service,
subscription { aor
address
| callid
id
| full
}
Displays
subscription information for defined subscribers, based on defined parameters.
-
aor
address :
Clears session(s) by Address of Record.
-
callid
id : Specifies
a Call Identification Number as an 8-digit hexadecimal number.
-
full :
Displays all available information.
summary
Displays only a
summary of the subscriber information. The following filter keywords are valid
with this command:
access-type, active, active-charging-service, activity, all, asn-peer-address, asngw-service, asnpc-service, apn, bandwidth-policy, bearer-establishment, callid, card-num, cbb-policy, configured-idle-timeout, connected-time, dhcp-server, domain, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-service, hnbgw-service, hsgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-services, mme-address, mme-service, mseg-service, msid, msisdn, nat, network-requested, network-type, pcc-service, pcf, pdg-service, pdif-service, pdsn-service, pdsnclosedrp-service, pgw-address, plmn-type, profile-id, qci, rulebase, rulename <rule_name>, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgsn-address, sgw-address, sgw-service, smgr-instance, tx-data, ue-type, username, without-dynamic-rule, without-override-control, grep, more
tft
Displays the
current Traffic Flow Template (TFT) associated with the subscriber session.
The following
filter keywords are valid with this command:
active, all, apn, asn-peer-address, asngw-service, asnpc-service, bearer-establishment, bng-service, callid, card-num, ccoa-only, configured-idle-timeout, connected-time, dhcp-server, dormant, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, ggsn-service, gprs-service, gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-service, ha, ha-ipsec-only, ha-service, hsgw-service, idle-time, imei, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, lma-service, lns, lns-service, long-duration-time-left, mag-service, mip-udp-tunnel-only, mipv6ha-service, mme-address, mme-service, msid, msisdn, nat, nemo-only, network-requested, network-type, pcf, pdg-service, pdif-service, pdsn-service, pgw-address, plmn-type, profile-id, profile-name, qci, rx-data, s1u-state, s5-proto, session-time-left, sgsn-address, sgw-address, sgw-service, smgr-instance, tx-data, username, grep, more
tx-data [ < | > | greater-than | less-than ]
value
The number of
bytes transmitted by the specified subscriber.
-
< : Filters
output so that only information less than the specified value is displayed.
-
> : Filters
output so that only information greater than the specified value is displayed.
-
greater-than :
Filters output so that only information greater than the specified value is
displayed.
-
less-than :
Filters output so that only information less than the specified value is
displayed.
-
value : Used
in conjunction with <, >, greater-than, less-than, If no other filtering
options are specified only output matching
value is
displayed. If
value is not
specified all data is displayed.
value must be
an integer from 0 through 18446744073709551615.
The following
filter keywords are valid with this command:
epdg-address, epdg-service,
ue-type { ims | non-ims }
Displays
information for the subscribers based on User Equipment type.
- ims : IP Multimedia Subsystem
- non-ims : UE other than IMS
The following
filter keywords are valid with this command:
access-type, active-charging-service, bandwidth-policy, bearer-establishment, callid, card-num, cbb-policy, configured-idle-timeout, connected-time, domain, ebi, enodeb-address, epdg-address, epdg-service, fa, fa-service, firewall, fw-and-nat, gprs-service, gtp-version, gtpu-bind-address, gtpu-service, ha, hnbgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-tunnel-remote-addr, long-duration-time-left, msid, nat, network-type, pcc-service, profile-id, qci, rulebase, rx-data, s1u-state, s5-proto, security-type, session-time-left, sgw-address, smgr-instance, tx-data, ue-type, username, grep, more
username
name
Displays
information for connections for the subscriber identified by
name . The
user must have been previously configured.
name must be
a sequence of characters and/or wildcard characters ('$' and '*') from 1 to 127
characters. The * wildcard matches multiple characters and the $ wildcard
matches a single character. If you do not want the wildcard characters
interpreted as a wildcard enclose them in single quotes ( '). For example; '$'.
The following
filter keywords are valid with this command:
epdg-address, epdg-service,
wf1
Displays
subscriber information in wide format number 1. Wide format number 1 includes
the following information for each listed subscriber session:
-
Access Type
-
Access
Technology
-
Call State
-
Link Status
-
Network Type
-
Call ID
-
MSID
-
Username
-
IP Address
-
Time-Idle
-
Access Peer
Address
-
Service
Address
-
Network Peer
Address
-
Connect Time
The following
filter keywords are valid with this command:
epdg-address, epdg-service,
without-dynamic-rule
Displays subscribers without any dynamic rule associated with them.
without-override-control
Displays subscribers without any override control rule associated with
them.
filter_keywords
The following
keywords are filters that modify or filter the output of the Command Keywords.
Not all filters are available for all Command Keywords. Multiple Filter
Keywords can be entered on a command line.
When multiple
Filter Keywords are specified, the output conforms to all of the Filter
Keywords specifications.
For example; if
you enter the following command:
show subscribers counters ip-pool pool1 card-num 1
Counters for all
subscriber sessions that were assigned an IP address from the IP pool named
pool1 and also are being processed by the processing card in slot 1 is
displayed. Information for all other subscribers is not displayed.
active
Only display
information for those subscribers who currently have active sessions.
active-charging-service
acs_service
Displays
information for subscribers being processed by the active charging service
specified as an alphanumeric string of 1 through 15 characters.
activity
Displays
subscriber link activity percentage.
all
If no keywords are
specified before
all,
information for all subscribers is displayed. If keywords are specified before
all, all
information is displayed with no further options being allowed.
apn
name
Displays subscribers currently facilitated by the access point
name (APN) configured on the SGSN or GGSN.
asngw-only
Displays counters for subscribers accessing the ASN-GW service
only.
asnpc-only
Displays counters for subscribers accessing the ASN Paging
Controller and Location Registry service only.
bandwidth-policy
policy_name
Displays
information for subscribers associated with the specified Active Charging
bandwidth policy.
bearer-establishment { direct-tunnel | normal | pending
}
id
Displays
subscriber information for selected bearer establishment type.
bng-service
srvc_name
Displays the
current configuration for the specified Broadband Network Gateway (BNG)
service.
callid
id
Displays
subscriber information for the call ID specified as an 8-byte hexadecimal
number.
card-num
card_num
The slot number of
the processing card by which the subscriber session is processed. The slot
number is an integer from 1 through 7 and 10 through 16 on the ASR 5000, or 1
through 4 and 7 through 10 on the ASR 5500.
cbb-policy
policy_name
Displays
information for subscribers associated with the specified Active Charging
Content Based Billing (CBB) policy.
ccoa-only
Displays the
subscribers that registered a MIP with CoA directly with the HA.
This option is
only valid when a MIPHA session license is enabled.
configuration { all | username
name
}
Displays current
configuration for all subscribers or a specified subscriber.
configured-idle-timeout [ < | > | greater-than | less-than
]
value
Shows the idle
timeout that is configured for the specified subscriber. A value of 0 (zero)
indicates that the subscribers idle timeout is disabled.
< : Filters output so that only information less
than the specified value is displayed.
> : Filters output so that only information
greater than the specified value is displayed.
greater-than : Filters output so that only
information greater than the specified value is displayed.
less-than : Filters output so that only information
less than the specified value is displayed.
value : Used in conjunction with <, >,
greater-than, less-than, If no other filtering options are specified only
output matching
value is
displayed. If
value is not
specified all data is displayed.
value must be
an integer from 0 through 4294967295.
connected-time [
< |
> |
greater-than
|
less-than ]
value
Shows how long the
subscriber has been connected.
< : Filters
output so that only information less than the specified value is displayed.
-
< : Filters
output so that only information less than the specified value is displayed.
-
> : Filters
output so that only information greater than the specified value is displayed.
-
greater-than :
Filters output so that only information greater than the specified value is
displayed.
-
less-than :
Filters output so that only information less than the specified value is
displayed.
-
value : Used
in conjunction with <, >, greater-than, less-than, If no other filtering
options are specified only output matching
value is
displayed. If
value is not
specified all data is displayed.
value must be
an integer from 0 through 4294967295.
counters
keyword
Displays the specified counter for the subscribers.
cpu-num
number
Displays information for calls processed through the specified
CPU number.
dhcp-server
address
Displays
subscribers currently accessing the system that have been provided an IP
address by the DHCP server specified by its address. GGSN only.
dns-proxy
Displays all
subscribers associated with a DNS proxy.
domain
name
Displays all
subscribers with an Address-of-Record (AoR) from the specified domain.
name is an
alphanumeric string of 1 through 79 characters.
dormant
Shows information
for subscriber sessions that are dormant (not transmitting or receiving data).
dormant
Shows information
for subscriber sessions that are dormant (not transmitting or receiving data).
ebi
number
Displays subscribers based on an EPS bearer identity number.
enodeb-address
ip_address
Displays
subscribers based on the eNodeB to which they are attached.
epdg-address
ip_address
Displays
information of subscribers connected to the specified ePDG address in IPv4
dotted-decimal notation or IPv6 (::) notation.
epdg-service
service_name
Displays
information of subscribers of ePDG service specified as an alphanumeric string
of 1 through 63 characters.
fa
address
Displays
information for subscribers connected to the foreign agent specified by its IP
address in IPv4 dotted-decimal notation.
fa-only
Only display
FA-specific context information.
fa-service
name
Displays
information for subscribers connected to the named foreign agent (FA) service.
firewall { not-required | required }
Displays information for the specified subscribers:
firewall-policy
fw_policy_name
This keyword is obsolete.
full
Displays all available information for subscribers.
fw-and-nat policy
fw_nat_policy
Important |
This option is
customer-specific and is only available in StarOS 8.1.
|
Displays information for subscribers using an existing
Firewall-and-NAT policy specified as an alphanumeric string of 1 through 15
characters.
ggsn-address
ip_address
Displays information for subscribers connected to an existing
GGSN specified by its IP address in IPv4 doted-decimal notation. SGSN only
ggsn-preservation-mode
Displays information for subscribers connected to the GGSN
service with preservation mode enabled. GGSN only.
ggsn-service
name
Displays information for subscribers connected to the named GGSN
service. This keyword is for GGSN only.
gprs-only
Displays only 2G SGSN subscribers content. SGSN only.
gprs-service
srvc_name
Displays
subscriber information for the named 2G GPRS service. SGSN only.
gsm-traffic-class { background | conversational | interactive |
streaming }
Displays
information for subscriber traffic that matches the specified 3GPP traffic
class.
-
background :
3GPP QoS background class.
-
conversational : 3GPP QoS conversational class.
-
interactive :
3GPP QoS interactive class. Must be followed by a traffic priority.
-
streaming :
3GPP QoS streaming class.
ha
address
Displays
information for subscribers connected to the home agent specified by its IP
address in IPv4 dotted-decimal notation.
ha-ipsec-only
Only displays
information for subscriber sessions that are using IP-Security (IPSec).
ha-only
Only displays
HA-specific context information.
ha-service
name
Displays
information for subscribers connected to the named home agent service.
hnbgw-only
Displays counters
for subscribers accessing the Home evolved NodeB Gateway (HNB-GW) service only.
idle-time [ < | > | greater-than | less-than ]
value
Displays how long
the subscriber session has been idle or display subscriber sessions that meet
the idle time criteria specified.
-
< : Filters
output so that only information less than the specified value is displayed.
-
> : Filters
output so that only information greater than the specified value is displayed.
-
greater-than :
Filters output so that only information greater than the specified value is
displayed.
-
less-than :
Filters output so that only information less than the specified value is
displayed.
-
value : Used
in conjunction with <, >, greater-than, less-than, If no other filtering
options are specified only output matching
value is
displayed. If
value is not
specified all data is displayed.
value must be
an integer from 0 through 4294967295.
imei
imei_number
Displays
information for subscribers having the specified International Mobile Equipment
Identity (IMEI/IMEISV) number.
ims-auth-service
service_name
Displays
information for subscribers for an existing IMS Authorization Service name.
imsi
id
Displays the
subscriber with the specified ID. The IMSI (International Mobile Subscriber
Identity) ID is a 15-character string which identifies the subscriber's home
country and carrier. Wildcard characters $ and * are allowed. The * wildcard
matches multiple characters and the $ wildcard matches a single character. If
you do not want the wildcard characters interpreted as a wildcard enclose them
in single quotes ( ' ). For example; '$'.
ip-address [ < | > | greater-than | less-than ]
address
Displays
information for subscribers connected to the specified
address .
-
< : Filters
output so that only information for subscribers with an IP address lower than
the specified address is displayed.
-
> : Filters
output so that only information for subscribers with an IP address higher than
the specified address is displayed.
-
greater-than :
Filters output so that only information for subscribers with an IP address
higher than the specified address is displayed.
-
less-than :
Filters output so that only information for subscribers with an IP address
lower than the specified address is displayed.
-
address : The
address must be specified using IPv4 dotted-decimal notation. Used in
conjunction with <, >, greater-than, less-than. If the IP address is
specified without a qualifier, only subscribers with the specified IP address
have their information displayed.
ip-alloc-method {aaa-assigned | dhcp [ relay-agent |
proxy-client ] | dynamic-pool | l2tp-lns-assigned | mip-ha-assigned |
ms-provided-static | not-ms-provided-static | static pool
}
Displays the
specific IP Allocation Method. Must be followed by one of the IP Allocation
Methods:
-
aaa-assigned :
Selects subscribers whose IP addresses were assigned by AAA.
-
dhcp : Selects
subscribers whose IP addresses were assigned by DHCP.
-
dynamic-pool :
Selects subscribers whose IP addresses were assigned from a dynamic IP address
pool.
-
l2tp-lns-assigned : Selects subscribers whose IP
addresses were assigned by the Layer 2 Tunneling Protocol (LT2P) Network
Server.
-
mip-ha-assigned : Selects subscribers whose IP
addresses were assigned by the Mobile IP Home Agent.
-
ms-provided-static : Selects subscribers whose IP
addresses were provided by the Mobile Station.
-
not-ms-provided-static : Selects subscribers whose
IP addresses were not provided by the Mobile Station.
-
static-pool :
Selects subscribers whose IP addresses were assigned from a static IP address
pool.
ip-pool
name
Displays
information for subscribers assigned addresses from an existing IP address pool
or IP pool group.
name will be
an IP address in IPv4 dotted-decimal or IPv6 colon-separated-hexadecimal
notation based on the call line setup for the specified pool.
ipv4
Displays
information for subscribers with an IPv4 Firewall enabled/disabled.
ipv6
Displays
information for subscribers with an IPv6 Firewall enabled/disabled.
ipv6-address
address
Displays
information for subscribers connected to the specified IPv6 address.
ipv6-prefix
prefix
Displays
information for subscribers connected to the specified IPv6 address prefix.
l3-tunnel-local-addr
ip_address
A layer 3
tunneling interface specified by its IP address in IPv4 dotted-decimal
notation.
l3-tunnel-remote-addr
ip_address
A layer 3
tunneling peer specified by its IP address in IPv4 dotted-decimal notation.
lac
address
Displays
information for calls to the peer L2TP Access Concentrator (LAC) specified by
its IP address.
lac-only
Displays LAC
specific information only.
lac-service
name [ local-tunnel-id id | remote-tunnel-id
id ]
Displays
information for calls associated with the LAC service specified as an
alphanumeric string of 1 through 63 characters.
-
local-tunnel-id
id : Specifies
a local tunnel from which to clear calls as an integer from 1 through 65535.
-
remote-tunnel-id
id : Specifies
a remote tunnel from which to clear calls as an integer from 1 through 65535.
lns
address
Displays
information for calls to the peer L2TP Network Server (LNS) specified by its IP
address.
lns-only
Displays LNS
specific information only.
lns-service
name [
local-tunnel-id
id |
remote-tunnel-id
id ]
Displays
information for calls associated with the LNS service specified as an
alphanumeric string of 1 through 63 characters.
-
local-tunnel-id
id : Indicates
a specific local tunnel from which to clear calls.
id must be an
integer from 1 through 65535.
-
remote-tunnel-id
id : Indicates
a specific remote tunnel from which to clear calls.
id must be an
integer from 1 through 65535.
local-tunnel-id
identifier
Displays
information for a local tunnel identifier specified as an integer from 1 to
65535.
long-duration-time-left [ < | > | greater-than | less-than
]
value
Shows how much
time is left for the maximum duration of a specified subscriber session.
-
< : Filters
output so that only information less than the specified value is displayed.
-
> : Filters
output so that only information greater than the specified value is displayed.
-
greater-than :
Filters output so that only information greater than the specified value is
displayed.
-
less-than :
Filters output so that only information less than the specified value is
displayed.
-
value : Used
in conjunction with <, >, greater-than, less-than, If no other filtering
options are specified only output matching
value is
displayed. If
value is not
specified all data is displayed.
value must be
an integer from 0 through 4294967295.
mag-only
Displays Mobile
Access Gateway (MAG) subscriber session information.
mag-service
svc_name
Displays
subscriber information based on the Mobile Access Gateway (MAG) service name.
svc_name must
be an existing MAG service expressed as an alphanumeric string of 1 through 63
characters.
mip-udp-tunnel-only
Displays the
subscribers that negotiated MIP-UDP tunneling with the HA.
This option is
only valid when MIP NAT Traversal license is enabled.
mipv6ha-only
Displays
MIPV6HA-specific context information for the session.
mipv6ha-service
service_name
Displays specific
configured MIPV6 Home Agent service.
service_name
must have been previously defined.
msid
id
Displays
information for the mobile user identified by
id .
id must be
from 7 to 16 hexadecimal digits specified as an IMSI, MIN, or RMI. Wildcard
characters $ and * are allowed. The * wildcard matches multiple characters and
the $ wildcard matches a single character. If you do not want the wildcard
characters interpreted as a wildcard enclose them in single quotes ( ' ). For
example: '$'.
In case of
enforce imsi-min
equivalence is enabled on the chassis and MIN or IMSI numbers
supplied, this filter will show subscribers with a corresponding MSID (MIN or
IMSI) whose lower 10 digits matches to lower 10 digits of the supplied MSID.
show subscribers msid
ABCD0123456789 or
show subscribers msid
0123456789
will show any
subscriber with a MSID that match the lower 10 digits of MSID supplied, for
example, 0123456789.
msisdn
msisdn
Displays
information for the mobile user identified by the Mobile Subscriber ISDN Number
(MSISDN).
msisdn must be 7 to 16 digits; specified as an
IMSI, MIN, or RMI.
nat { not-required | required }
Displays information for the specified subscribers.
nat-ip
nat_ip_address
] }
Displays information for the subscribers for whom NAT processing
is enabled and are using the specified NAT IP address.
nat_ip_address specifies the NAT IP address and
must be in IPv4 dotted-decimal notation.
The nat-ip
keyword is only available in StarOS 8.3 and later releases.
nat-realm
nat_realm
Displays information for the subscribers for whom NAT processing
is enabled and are using the specified NAT realm.
nat_realm
specifies the NAT realm name and must be a string from 1 through 63 characters.
network-requested
Display information for currently active subscribers whose
sessions were initiated by the GGSN network requested create PDP context
procedure.
network-type { gre | ipip | ipsec | ipv4 | ipv4-pmipv6 | ipv4v6
| ipv4v6-pmipv6 | ipv6 | ipv6-pmipv6 | l2tp | mobile-ip | proxy-mobile-ip
}
Selects the currently active subscribers based on network
service access type.
- gre: Generic Routing Encapsulation
-
ipip :
IP-in-IP
-
ipsec : IPSec
-
ipv4 : IPv4
only
-
ipv4-pmipv6 :
IPv4 and/or Proxy Mobile IPv6 (PMIP)
-
ipv4v6 : IPv4
and/or IPv6
-
ipv4v6-pmipv6 : IPv4, IPv6 and/or Proxy Mobile IPv6
-
ipv6 : IPv6
only
-
ipv6-pmipv6 :
IPv6 and/or Proxy Mobile IPv6 (PMIP)
-
l2tp : Layer 2
Tunneling Protocol
-
mobile-ip :
Mobile IP (MIP)
-
proxy-modile-ip : Proxy Mobile IPv6 (PMIP)
nri
nri_value
This SGSN-specific filter uses the configured network resource
identifier (NRI) to identify a specific SGSN in a pool to fine-tuned the
subscriber information to be displayed.
nri_value : enter an integer from 0 through 63
This filter can be used in combination with further refining
filters.
nsapi
nsap_id
Displays session information for the mobile user identified by
Network Service Access Point Identifier (NSAPI) between MS and SGSN. NSAPI is
also used as part of the tunnel identifier between GPRS Support Nodes (GSNs).
The user identity IMSI and the application identifier (NSAPI) are integrated
into the Tunnel IDentifier (GTPv0) (TID) or Tunnel Endpoint Identifier (GTPv1)
(TEID) that uniquely identifies the subscriber's sublink between the GSNs (SGSN
and GGSN). The NSAPI is an integer value within the PDP context header.
nsap_id must
be an integer from 5 through 15.
partial qos { negotiated | requested }
This filter is specific to the SGSN.
Is limits the display of information to requested or negotiated
QoS information for the subscriber.
This filter can be used in combination with further defining
filters: active, active-charging-service, all, apn, callid, card-num,
configured-idle-timeout, connected-time, ggsn-address, gprs-service,
gsm-traffic-class, idle-time, imsi, msid, msisdn, negotiated, plmn-type,
requested, rx-data, session-time-left, tx-data
pcc-service
name
Displays statistics for users associated with an existing Policy
and Charging Control (PCC) service name expressed as an alphanumeric string of
1 through 63 characters.
pcf [
< | > | less-than | greater-than]
ipv4_address
[
<
| > | less-than |
greater-than ]
ipv4_address
]
Displays
information for subscribers connected via the packet control function with a
specific or range of IP addresses. The address must be specified using IPv4
dotted-decimal notation.
-
< : Filters
output so that only information less than the specified IPv4 address value is
displayed.
-
> : Filters
output so that only information greater than the specified IPv4 address value
is displayed.
-
less-than: Filters
output so that only information less than the specified IPv4 address value is
displayed.
-
greater-than: Filters
output so that only information greater than the specified IPv4 address value
is displayed.
Note: It is
possible to define a limited range of IP addresses by using the less-than and
greater-than options to define minimum and maximum values.
pdsn-only
Show PDSN specific
information only.
pdsn-service
name
Displays
information for subscribers connected to the packet data service
name . The
packet data service must have been previously configured.
pdsnclosedrp-service
service_name
Displays information for subscribers connected to the Closed R-P
service
service_name .
The Closed R-P service must have been previously configured.
plmn-type
Displays
subscriber type (HOME, VISITING, or ROAMING).
This keyword is
for the GGSN or the SGSN only.
policy
Displays the
current policies associated with the subscriber session.
profile-id
id_number
Displays
subscriber session information based on the profile-id granted for the flow.
id_number
must be an integer from 0 to 4294967295.
profile-name
profile_name
Displays the
subscribers filtered with PCC profile named
profile_name
in particular IP-CAN session.
qci
number
Displays
subscriber session information based on the QoS Class Identifier (QCI) value
assigned to the subscriber.
number must
be an integer value from 0 to 9.
relay-agent
Selects
subscribers whose IP Addresses were assigned by the DHCP Relay Agent.
remote-tunnel-id
identifier
Displays
information for a remote tunnel identifier specified as an integer from 1 to
65535.
rnc id
rnc_id mcc
mcc_num mnc
mnc_num
Displays information for subscribers connected to the SGSN via a
specific RNC (radio network controller) identified by the RNC ID, the MCC
(mobile country code), and the MNC (mobile network code). SGSN only
rulebase
name
Selects
subscribers associated with the specified Active Charging rulebase.
rx-data [ < | > | greater-than | less-than ]
value
The number of
bytes received by the specified subscriber.
-
< : Filters
output so that only information less than the specified value is displayed.
-
> : Filters
output so that only information greater than the specified value is displayed.
-
greater-than :
Filters output so that only information greater than the specified value is
displayed.
-
less-than :
Filters output so that only information less than the specified value is
displayed.
-
value : Used
in conjunction with <, >, greater-than, less-than, If no other filtering
options are specified only output matching
value is
displayed. If
value is not
specified all data is displayed.
value must be
an integer from 0 through 18446744073709551615.
saegw-only
Displays System Architecture Evolution Gateway (SAEGW)
subscriber session information only.
saegw-service
svc_name
Displays subscriber information based on the SAEGW service name.
svc_name must
be an existing SAEGW service expressed as an alphanumeric string of 1 through
63 characters.
security-type { ipsec | tls }
Displays subscriber information based on the specified type of
security.
- ipsec : IPSec
- tls : Transport Layer Security
session-time-left [ < | > | greather-than | less ]
value
How much session
time is left for the specified subscriber.
-
< : Filters
output so that only information less than the specified value is displayed.
-
> : Filters
output so that only information greater than the specified value is displayed.
-
greater-than :
Filters output so that only information greater than the specified value is
displayed.
-
less-than :
Filters output so that only information less than the specified value is
displayed.
-
value : Used
in conjunction with <, >, greater-than, less-than, If no other filtering
options are specified only output matching
value is
displayed. If
value is not
specified all data is displayed.
value must be
an integer from 0 through 4294967295.
smgr-instance
number
Specific sessmgr
instance.
number must
be in the range of 1 to 4294967295.
sgsn-address
address
Shows information for subscribers whose PDP contexts are
currently being facilitated by the SGSN specified by address. This command is
for GGSN only.
sgsn-service
srvc_name
Shows subscriber information for a specified 3G SGSN service.
srvc_name
must be an alphanumeric string of 1 through 63 characters that identifies a
configured SGSN service.
This command is for SGSN only.
subscription { aor
address
| callid
id
| full
}
Displays
subscription information for defined subscribers, based on defined parameters.
-
aor
address :
Clears session(s) by Address of Record.
-
callid
id : Specifies
a Call Identification Number as an 8-digit hexadecimal number.
-
full :
Displays all available information.
tft
Displays the
current Traffic Flow Template (TFT) associated with the subscriber session.
tpo { not-required | required }
Important |
The Traffic
Performance Optimization (TPO) in-line service is not supported in this
release.
|
Displays information for
specified subscribers.
tx-data [ < | > | greater-than | less-than ]
value
The number of
bytes transmitted by the specified subscriber.
-
< : Filters
output so that only information less than the specified value is displayed.
-
> : Filters
output so that only information greater than the specified value is displayed.
-
greater-than :
Filters output so that only information greater than the specified value is
displayed.
-
less-than :
Filters output so that only information less than the specified value is
displayed.
-
value : Used
in conjunction with <, >, greater-than, less-than, If no other filtering
options are specified only output matching
value is
displayed. If
value is not
specified all data is displayed.
value must be
an integer from 0 through 18446744073709551615.
ue-type { ims | non-ims }
Displays
information for the subscribers based on User Equipment type.
- ims : IP Multimedia Subsystem
- non-ims : UE other than IMS
username
name
Displays
information for connections for the subscriber identified by
name . The
user must have been previously configured.
name must be
a sequence of characters and/or wildcard characters ('$' and '*') from 1 to 127
characters. The * wildcard matches multiple characters and the $ wildcard
matches a single character. If you do not want the wildcard characters
interpreted as a wildcard enclose them in single quotes ( '). For example; '$'.
verbose
Display detailed
information.
wide-format
Display detailed
information in a wider screen format.
| { grep
grep_options | more }
Pipes (sends) the
output of the command to the command specified. You must specify a command to
which the output will be sent.
For details on the
usage of the
grep and
more
commands, refer to the
Regulating a
Command's Output section of the
Command Line
Interface Overview chapter.
Usage Guidelines
Use this command
to view information about subscriber sessions.
The output of this
command may be considered for part of a periodic system auditing program by
verifying active and dormant subscribers.
The Command
Keywords may be used standalone to display detailed information or you may use
one or more of the various Filter Keywords to reduce the amount of information
displayed.
Caution |
Executing this
command may negatively impact performance if multiple instances are executed
while the system is under heavy load and simultaneously facilitating multiple
CLI sessions.
|
Example
The following
command displays information for all subscriber sessions:
show subscribers all
The following command displays information for all ggsn-only
subscriber sessions:
show subscribers ggsn-only all
The following
command displays information for all subscriber sessions in wide format 1:
show subscribers wf1 all
show subscribers aaa-configuration
show subscribers counters username isp1user1
The following command displays information for subscriber in
GGSN service:
show subscribers ggsn-only all
show subscribers ggsn-only full
The following command displays information for all subscriber
with SGSN session having partial QoS requests:
show subscribers sgsn-only partial qos requested
The following
command displays information for all subscriber with MME session connected to
MME service having IP address as
10.1.1.1 :
show subscribers mme-only mme-address 10.1.1.1
Important |
Output
descriptions for commands are available in the
Statistics
and Counters Reference.
|