This command specifies the name of the interface applicable for a
specific Network Element (NE) on which subscriber session traces have to be
collected.
Product
GGSN
MME
P-GW
SAEGW
S-GW
Privilege
Security Administrator, Administrator
Mode
Exec > Global Configuration > Session Trace Template
Configuration
configure > template-session-trace network-element { {
enb template-name cell-trace } | { { ggsn | hnbgw | mme | pgw | saegw | sgw }
template-name
template_name } }
Entering the above command sequence results in the following prompt:
[local]host_name(config-sesstrc-template)#
Syntax
[ no ] interface interface_name
no
Disables its following configured options.
interface_name
Specifies the interface name for tracing. The available interfaces
depend on the
network-element selected.
GGSN. The available
ggsn interfaces are:
- all: Specifies that all interfaces are to be traced.
- gi: Specifies that the interface where the trace will be
performed is the Gi interface between the GGSN and RADIUS server.
- gmb: Specifies that the interface where the trace will be
performed is the Gmb interface between the GGSN and BM-SC.
- gn: Specifies that the interface where the trace will be
performed is the Gn interface between the GGSN and the SGSN.
- gx: Specifies that the interface where the trace will be
performed is the Gx interface between the GGSN and PCRF.
- gy: Specifies that the interface where the trace will be
performed is the Gy interface between the GGSN and OCS.
HNBGW. The available interfaces for
hnbgw are as follows:
- all: Specifies that all
hnbgw interfaces are to be traced.
- iucs: Specifies that the interface where the trace will be
performed is the
iucs interface between the HNB-GW and the
Mobile Switching Centre (3G MSC) in a 3G UMTS Femtocell Access Network.
- iups: Specifies that the interface where the trace will be
performed is the
iups interface between the HNB-GW and the
SGSN.
MME. The available interfaces for
mme
are as follows:
- all
- s10: Specifies that the interface where the trace will be
performed is the S10 interface between the MME and another MME.
- s11: Specifies that the interface where the trace will be
performed is the S11 interface between the MME and the S-GW.
- s13: Specifies that the interface where the trace will be
performed is the S13 interface between the MME and the EIR.
- s1mme: Specifies that the interface where the trace will be
performed is the S1-MME interface between the MME and the eNodeB.
- s3: Specifies that the interface where the trace will be
performed is the S3 interface between the MME and an SGSN.
- s6a: Specifies that the interface where the trace will be
performed is the S6a interface between the MME and the HSS.
PGW. The available interfaces for
pgw are as follows:
- all : Specifies that all interfaces are to
be traced.
- gx : Specifies that the interface where
the trace will be performed is the Gx interface between the P-GW and the PCRF.
- gy : Specifies that the interface where
the trace will be performed is the Gy interface between the P-GW and OCS.
- s2a : Specifies that the interface where
the trace will be performed is the S2a interface between the P-GW and the HSGW.
- s2b : Specifies that the interface where
the trace will be performed is the S2b interface between the P-GW and an ePDG.
- s2c : Specifies that the interface where
the trace will be performed is the S2c interface between the P-GW and a
trusted, non-3GPP access device.
- s5 : Specifies that the interface where
the trace will be performed is the S5 interface between an S-GW and P-GW
located within the same administrative domain (non-roaming).
- s6b : Specifies that the interface where
the trace will be performed is the S6b interface between the P-GW and the 3GPP
AAA server.
- s8 : Specifies that the interface where
the trace will be performed is the S8 interface -- an inter-PLMN reference
point between the S-GW and the P-GW used during roaming scenarios.
- sgi : Specifies that the interface where
the trace will be performed is the SGi interface between the P-GW and the PDN.
SAEGW: The available interfaces for the SAEGW are as follows:
- func-pgw interface : The following
interfaces are available for a configured P-GW under an SAEGW service:
- all : Specifies that all interfaces
are to be traced.
- gx : Specifies that the interface
where the trace will be performed is the Gx interface between the P-GW and the
PCRF.
- gy : Specifies that the interface
where the trace will be performed is the Gy interface between the P-GW and OCS.
- s2a : Specifies that the interface
where the trace will be performed is the S2a interface between the P-GW and the
HSGW.
- s2b : Specifies that the interface
where the trace will be performed is the S2b interface between the P-GW and an
ePDG.
- s2c : Specifies that the interface
where the trace will be performed is the S2c interface between the P-GW and a
trusted, non-3GPP access device.
- s5 : Specifies that the interface
where the trace will be performed is the S5 interface between an S-GW and P-GW
located within the same administrative domain (non-roaming).
- s6b : Specifies that the interface
where the trace will be performed is the S6b interface between the P-GW and the
3GPP AAA server.
- s8 : Specifies that the interface
where the trace will be performed is the S8 interface -- an inter-PLMN
reference point between the S-GW and the P-GW used during roaming scenarios..
- sgi : Specifies that the interface
where the trace will be performed is the SGi interface between the P-GW and the
PDN.
- func-sgw interface : The following
interfaces are available for a configured S-GW under an SAEGW service:
- all : Specifies that all interfaces
are to be traced.
- gxc : Specifies that the interface
where the trace will be performed is the Gxc interface between the S-GW and the
PCRF.
- s11 : Specifies that the interface
where the trace will be performed is the S11 interface between the S-GW and the
MME.
- s4 : Specifies that the interface
where the trace will be performed is the S4 interface between the S-GW and an
SGSN.
- s5 : Specifies that the interface
where the trace will be performed is the S5 interface between the S-GW and the
P-GW.
- s8 : Specifies that the interface
where the trace will be performed is the S8 interface between the S-GW and the
P-GW.
SGW. The available interfaces for the S-GW are as follows:
- all : Specifies that all interfaces are to
be traced.
- gxc : Specifies that the interface where
the trace will be performed is the Gxc interface between the S-GW and the PCRF.
- s11 : Specifies that the interface where
the trace will be performed is the S11 interface between the S-GW and the MME.
- s4 : Specifies that the interface where
the trace will be performed is the S4 interface between the S-GW and an SGSN.
- s5 : Specifies that the interface where
the trace will be performed is the S5 interface between the S-GW and the P-GW.
- s8 : Specifies that the interface where
the trace will be performed is the S8 interface between the S-GW and the P-GW.
Usage Guidelines
The
interface
command is specific to Session Tracing. This command is
available in the template for the MME NE. This command specifies the interfaces
for Session Tracing from the MME.
Example
The following command selects S1-MME as the interface for session
tracing:
interface s1mme
Feedback