Traffic Optimization Profile Configuration Mode Commands

The Traffic Optimization Profile Configuration Mode allows you to configure and manage properties of Cisco Ultra Traffic Optimization solution.

Mode

Exec > ACS Configuration > Traffic Optimization Profile Configuration

active-charging service service_name > traffic-optimization-profile

Entering the above command sequence results in the following prompt: 

[local]host_name(config-traffic-optim)#

Important

The commands or keywords/variables that are available are dependent on platform type, product version, and installed license(s).

data-record

This command enables Traffic Optimization Data Record (TODR) generation.

Product

P-GW

Privilege

Security Administrator, Administrator

Mode

Exec > ACS Configuration > Traffic Optimization Profile Configuration

active-charging service service_name > traffic-optimization-profile

Entering the above command sequence results in the following prompt: 

[local]host_name(config-traffic-optim)#

Syntax

data-record [ large-flows-only | managed-large-flows-only ] 
no data record

no

If previously configured, disables generation of TODR.

data-record

Enables the Traffic Optimization Data Record (TODR) generation

  • large-flows-only : Enables the traffic optimization data record generation for large flows.

    managed-large-flows-only : Enables the traffic optimization data record generation for managed large flows.

    The keywords - large-flows-only and managed-large-flows-only when configured along with data-record enables the CUTO library to stream the respective statistics as part of the stats-options command, to the external server. The user can configure a combination of the stats-options keywords flow-trace and flow-analyst and the data-record command to notify the CUTO library accordingly.


    Note

    One of the above the two keywords can be configured as part of the data-record, which will enable the CUTO library to stream the respective statistics.

    The default behavior of the data-record command is not affected with the above implementation . If it is configured without any of the options, then TODR’s will be generated for all standard and large flows, which is the existing behavior.

Usage Guidelines

Use this command to generate TODR.

efd-flow-cleanup-interval

This configures EFD flow command cleanup interval.

Product

P-GW

Privilege

Security Administrator, Administrator

Mode

Exec > ACS Configuration > Traffic Optimization Profile Configuration

active-charging service service_name > traffic-optimization-profile

Entering the above command sequence results in the following prompt: 

[local]host_name(config-traffic-optim)#

Syntax

[ no ] efd-flow-cleanup-interval

no

If previously configured, disables EFD flow cleanup interval.

efd-flow-cleanup-interval

Configures EFD flow cleanup interval. The interval value is an integer that ranges from 10 to 5000 milliseconds.

Usage Guidelines

Use this command to configure EFD flow cleanup interval.

end

Exits the current configuration mode and returns to the Exec mode.

Product

All

Privilege

Security Administrator, Administrator

Syntax

end

Usage Guidelines

Use this command to return to the Exec mode.

exit

Exits the current mode and returns to the parent configuration mode.

Product

All

Privilege

Security Administrator, Administrator

Syntax

exit

Usage Guidelines

Use this command to return to the parent configuration mode.

heavy-session detection-threshold

Configures the threshold value for the TCP flow to be considered for the Traffic Optimization.

Product

P-GW

Privilege

Security Administrator, Administrator

Mode

Exec > ACS Configuration > Traffic Optimization Profile Configuration

active-charging service service_name > traffic-optimization-profile

Entering the above command sequence results in the following prompt: 

[local]host_name(config-traffic-optim)#

Syntax

heavy-session detection-threshold bytes

heavy-session

Specifies the heavy session configuration for the Traffic Optimization.

detection-threshold bytes

Specifies the detection threshold, in bytes. Beyond which, it is considered as heavy session. The bytes must be an integer from 1 to 4294967295.

To get optimum Traffic Optimization benefit, it is recommended to not set it less than 3 MB.

Usage Guidelines

Use this command to set the threshold value for the TCP flow.

Examples

The following command sets the threshold value to 3145728 bytes: 
heavy-session detection-threshold 3145728

mode

Configures the operating mode for the Cisco Ultra Traffic Optimization engine.

Product

P-GW

Privilege

Security Administrator, Administrator

Mode

Exec > ACS Configuration > Traffic Optimization Profile Configuration

active-charging service service_name > traffic-optimization-profile

Entering the above command sequence results in the following prompt: 

[local]host_name(config-traffic-optim)#

Syntax

mode [ active | passive ]

mode

Sets the mode of operation for Traffic Optimization.

active

The mode where both Traffic Optimization and flow monitoring is done on the packet.

passive

The mode where no flow-control is performed but monitoring is done on the packet.

Usage Guidelines

Use this command to set the operating mode for the Cisco Ultra Traffic Optimization engine.

Examples

The following command sets the operating mode to active : 
mode active

stats-interval

This command configures the flow statistics collection and reporting interval.

Product

P-GW

Privilege

Security Administrator, Administrator

Mode

Exec > ACS Configuration > Traffic Optimization Profile Configuration

active-charging service service_name > traffic-optimization-profile

Entering the above command sequence results in the following prompt: 

[local]host_name(config-traffic-optim)#

Syntax

[ no ] stats-interval

no

If previously configured, disables collection of flow statistics.

stats-interval

Configures the flow statistics collection and reporting interval in seconds. The interval value is an integer that ranges from 1 to 60 seconds.

Usage Guidelines

Use this command to collect and report flow statistics.

stats-options

This command configures options to collect the flow statistics.

Product

P-GW

Privilege

Security Administrator, Administrator

Mode

Exec > ACS Configuration > Traffic Optimization Profile Configuration

active-charging service service_name > traffic-optimization-profile

Entering the above command sequence results in the following prompt: 

[local]host_name(config-traffic-optim)#

Syntax

[ no ] stats-options { flow-analyst [ flow-trace ] | flow-trace [ flow-analyst ] }

no

If previously configured, disables trace collection and reporting.

flow-analyst

Enables flow analysis, and large trace collection and reporting.

flow-trace

Enables flow trace collection and reporting.

Usage Guidelines

Use this command to enable trace collectiona and reporting.