SCCP Network Configuration Mode Commands

Signaling Connection Control Part (SCCP) is a routing protocol in the SS7 protocol suite in layer 4, which provides end-to-end routing for TCAP messages to their proper database.

Mode

The SCCP Network Configuration Mode is used to configure properties for Signaling Connection Control Part (SCCP) services for SS7.

Exec > Global Configuration > SCCP Network Configuration

configure > sccp-network id_number

Entering the above command sequence results in the following prompt: 

[local]host_name(config-sccp-network-sccp_id)#

Important

The commands or keywords/variables that are available are dependent on platform type, product version, and installed license(s).

associate

Associates an SS7 routing domain with the SCCP network.


Important

In Release 20 and later, HNBGW is not supported. This command must not be used for HNBGW in Release 20 and later. For more information, contact your Cisco account representative.

Product

SGSN

HNB-GW

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > SCCP Network Configuration

configure > sccp-network id_number

Entering the above command sequence results in the following prompt: 

[local]host_name(config-sccp-network-sccp_id)#

Syntax

associate ss7-routing-domain rd_id 
no associate

no

Removes the association with the SS7 routing domain from the system configuration.

rd_id

This number identifies an already defined SS7 routing domain.

rd_id: enter an integer from 1 through 12.

Usage Guidelines

Use this command to associate SS7 routing domain configurations with SCCP network configurations.

Examples

The following command associates the SCCP network with SS7 routing domain 2: 
associate ss7-routing-domain 2

description

This command defines a string that describes the SCCP network. The description is used for operator reference.


Important

In Release 20 and later, HNBGW is not supported. This command must not be used for HNBGW in Release 20 and later. For more information, contact your Cisco account representative.

Product

SGSN

HNB-GW

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > SCCP Network Configuration

configure > sccp-network id_number

Entering the above command sequence results in the following prompt: 

[local]host_name(config-sccp-network-sccp_id)#

Syntax

description string 
no description

string

This is a string to describe the SCCP network.

string must be an alphanumeric string from 1 through 127 characters in length. If there are spaces in the string the string must be enclosed in double-quotes. For example; "This is a Description".

no

Removes the description from the system configuration.

Usage Guidelines

Use this command to configure a description of this SCCP service for operator reference.

Examples

The following command sets the description to "This is the SCCP Service Number 1": 
description "This is the SCCP Service Number 1."

destination

This command configures the SCCP network destination information. Use this command multiple times to set all of the destination information required.


Important

In Release 20 and later, HNBGW is not supported. This command must not be used for HNBGW in Release 20 and later. For more information, contact your Cisco account representative.

Product

SGSN

HNB-GW

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > SCCP Network Configuration

configure > sccp-network id_number

Entering the above command sequence results in the following prompt: 

[local]host_name(config-sccp-network-sccp_id)#

Syntax

destination dpc pt_code { name route_name | next-hop pt_code [ priority priority ] | ssn subsys_num | version sccp_ver } 
no destination dpc p_code [ name route_name | ssn  ssn_num | version sccp_ver ]

no

Deletes the specified destination information from the SCCP network configuration.

dpc pt_code

Specifies the SCCP destination point code.

pt_code: Must be in SS7 point code dotted-decimal ###.###.### format or decimal ######## format.

name route_name

The name of the SCCP destination route.

route_name: enter an alphanumeric string from 1 through 64 characters in length.

next-hop pt_code [ priority priority

Associates the next destination defined in the SS7 routing domain and assigns the next-hop a priority for use.

pt_code: Must be in SS7 point code dotted-decimal ###.###.### format or decimal ######## format.

priority: Must be an integer from 0 to 15, with 0 setting the highest priority.

ssn subsys_num

The destination subsystem number.

subsys_num: enter an integer from 1 through 255.

version sccp_ver

sccp_ver: enter one of the following to select the SCCP variant:

  • ANSI88

  • ANSI92

  • ANSI96

  • BELL05

  • CHINA

  • GSM0806

  • ITU88

  • ITU92

  • ITU96

Usage Guidelines

Use this command to configure the destination information for the SCCP network.

Examples

The following commands set the name of the destination route to default_route, the subsystem number to 1, and the variant version to ITU96, all with a destination point code of 1: 
destination dpc 1 name default_route 
destination dpc 1 ssn 1 
destination dpc version ITU96

do show

Executes all show commands while in Configuration mode.

Product

All

Privilege

Security Administrator, Administrator

Syntax

do show

Usage Guidelines

Use this command to run all Exec mode show commands while in Configuration mode. It is not necessary to exit the Config mode to run a show command.

The pipe character | is only available if the command is valid in the Exec mode.


Caution

There are some Exec mode show commands which are too resource intensive to run from Config mode. These include: do show support collection , do show support details , do show support record and do show support summary . If there is a restriction on a specific show command, the following error message is displayed: 

Failure: Cannot execute 'do	show support' command from Config mode.

end

Exits the current configuration mode and returns to the Exec mode.

Product

SGSN

HNB-GW

Privilege

Security Administrator, Administrator

Syntax

end

Usage Guidelines

Return to the Exec mode.

exit

Exits the current configuration mode and returns to the global configuration mode.

Product

SGSN

HNB-GW

Privilege

Security Administrator, Administrator

Syntax

exit

Usage Guidelines

Return to the global configuration mode.

global-title-translation

This command associates a GTT address-map with this SCCP network.


Important

In Release 20 and later, HNBGW is not supported. This command must not be used for HNBGW in Release 20 and later. For more information, contact your Cisco account representative.

Product

SGSN

HNB-GW

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > SCCP Network Configuration

configure > sccp-network id_number

Entering the above command sequence results in the following prompt: 

[local]host_name(config-sccp-network-sccp_id)#

Syntax

global-title-translation address-map instance instance 
no global-title-translation address-map instance instance

no

Deletes the GTT address-map instance associated with this SCCP network.

instance

This value uniquely identifies a specific previously defined instance of a GTT address-map.

instance: enter an integer from 1 to 4096.

Usage Guidelines

Use this command to link a GTT address-map, configured with the GTT Address Map configuration mode, to a specific SCCP network configuration.

Examples

global-title-translation address-map instance gtt-map1

hop-count

This command specifies the hop count for this SCCP network.


Important

In Release 20 and later, HNBGW is not supported. This command must not be used for HNBGW in Release 20 and later. For more information, contact your Cisco account representative.

Product

SGSN

HNB-GW

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > SCCP Network Configuration

configure > sccp-network id_number

Entering the above command sequence results in the following prompt: 

[local]host_name(config-sccp-network-sccp_id)#

Syntax

hop-count hop_cnt 
default hop-count

default

Resets the hop-count value to the system default of 5.

hop_cnt

The hop count to assign to this SCCP network.

hop_cnt: enter an integer from 1 to 15.

Usage Guidelines

Use this command to define the hop count for this SCCP network.

Examples

The following command sets the hop count to 3: 
hop-count 3

self-point-code

This command specifies the SS7 point code for this SCCP service.


Important

In Release 20 and later, HNBGW is not supported. This command must not be used for HNBGW in Release 20 and later. For more information, contact your Cisco account representative.

Product

SGSN

HNB-GW

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > SCCP Network Configuration

configure > sccp-network id_number

Entering the above command sequence results in the following prompt: 

[local]host_name(config-sccp-network-sccp_id)#

Syntax

self-point-code point_code 
no self-point-code

no

Deletes the configured self point code.

point_code

Defines the point code to assign to this SCCP network service.

point_code: value entered must adhere to the point code variant selected when the SCCP network instance was defined:

  • ITU Range 0.0.1 to 7.255.7

  • ANSI Range 0.0.1 to 255.255.255

  • TTC Range 0.0.1 to 15.31.255

  • a string of 1 to 11 combined digits ad period.

Usage Guidelines

Use this command to assign the self point code to use for this SCCP service.

Examples

The following command sets an ITU-based point code for this SCCP service: 
self-pointcode 4.121.5
The following command removes the configured self-point code: 
no self-pointcode

timeout

This command configures the timeout parameters for this SCCP network.


Important

In Release 20 and later, HNBGW is not supported. This command must not be used for HNBGW in Release 20 and later. For more information, contact your Cisco account representative.

Product

SGSN

HNB-GW

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > SCCP Network Configuration

configure > sccp-network id_number

Entering the above command sequence results in the following prompt: 

[local]host_name(config-sccp-network-sccp_id)#

Syntax

timeout { attack-timer | congestion-timer | conn-est-timer | crd-timer | decay-timer | iar-timer | ias-timer | interval-timer | reassembly-timer | release-timer | repeat-release-timer | reset-timer | sst-timer } + 
default timeout 
no timeout timer

attack-timer time

Defines the time before the attack timer expires.

time: enter an integer between 1 and 10.

congestion-timer time

Defines the time before the congestion timer expires.

time: enter an integer between 1 and 10.

conn-est-timer time

Defines the time before the connection timer expires.

time: enter an integer between 6 and 12.

crd-timer time

Defines the time before the coordinated-state-change timer expires.

time: enter an integer between 60 and 120.

decay-timer time

Defines the time before the decay timer expires.

time: enter an integer between 1 and 10.

iar-timer time

Defines the time before the inactivity-receive timer expires.

time: enter an integer between 60 and 120.

ias-timer time

Defines the time before the inactivity-send timer expires.

time: enter an integer between 30 and 60.

interval-timer time

Defines the time before the interval timer expires.

time: enter an integer between 6 and 12

reassembly-timer time

Defines the time before the reassembly-timer expires.

time: enter an integer between 10 and 20.

release-timer time

Defines the time before the release-assembly timer expires.

time: enter an integer between 1 and 2.

repeat-release-timer time

Defines the time before repeat-release timer expires.

time: enter an integer between 1 and 2

reset-timer time

Defines the amount of time before the reset timer expires.

time: enter an integer between 1 and 2

sst-timer time

Defines the amount of time before the subsystem status test timer expires.

time: enter an integer between 5 and 1200.

default

Resets the timeout parameter to the system default.

no

Deletes the specified timer configuration.

Usage Guidelines

Use this command to assign timeout timers and timeout values for this SCCP service.

Examples

timeout reset-timer 75