Command Line Interface Reference, Modes I - Q, StarOS Release 21.24

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents

Find Matches in This Book

Results

Updated:: July 2, 2021

Chapter: Out-Address Configuration Mode Commands

Out-Address Configuration Mode Commands
gt-address
gt-format
ni-indicator
point-code
routing-indicator
ssf
ssn

Out-Address Configuration Mode Commands

Mode

The Out-Address configuration mode provides the commands to configure the outbound parameters for the SCCP entities as part of the gtt-address-map configuration.

Exec > Global Configuration > GTT Address-Map Configuration > Out-Address Configuration

configure > gtt address-map map_id > out-address address_name

Entering the above command sequence results in the following prompt:

[local]host_name(config-gtt-addrmap-outaddr-out_address)#

Important

The commands or keywords/variables that are available are dependent on platform type, product version, and installed license(s).

Important

For information on common commands available in this configuration mode, refer to the Common Commands chapter.

gt-address

Configures the SCCP short address.

Product

SGSN

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > GTT Address-Map Configuration > Out-Address Configuration

configure > gtt address-map map_id > out-address address_name

Entering the above command sequence results in the following prompt:

[local]host_name(config-gtt-addrmap-outaddr-out_address)#

Syntax

gt-address gt_address

`gt_address`

A string of 1 to 15 digits to define the GT-address

Usage Guidelines

Define the GT-address

Example

gt-address 010405525397

gt-format

The GT-format provides four formats that can be used during GTT.

Product

SGSN

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > GTT Address-Map Configuration > Out-Address Configuration

configure > gtt address-map map_id > out-address address_name

Entering the above command sequence results in the following prompt:

[local]host_name(config-gtt-addrmap-outaddr-out_address)#

Syntax

gt-format format_num

`format_num`

1: Selects GT-format 1 options which include nature-of-address and odd/even. Once selected, the system enters GT-Format1 configuration mode.

2: Selects GT-format2 options which include translation-type . Once selected, the system enters GT-Format2 configuration mode.

3: Selects GT-format3 options which include encoding-scheme , numbering-plan3 and translation-type . Once selected, the system enters GT-Format1 configuration mode.

4: Selects GT-format4 options which include encoding-scheme , nature-of-address , numbering-plan , and translation-type . Once selected, the system enters GT-Format4 configuration mode.

Usage Guidelines

Select the a GT-format that include encoding-scheme as part of the GTT process.

Example

gt-format 3

ni-indicator

Configures the National and International indicator to use during the GTT process.

Product

SGSN

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > GTT Address-Map Configuration > Out-Address Configuration

configure > gtt address-map map_id > out-address address_name

Entering the above command sequence results in the following prompt:

[local]host_name(config-gtt-addrmap-outaddr-out_address)#

Syntax

ni-indicator ni_ind

ni_ind

Select one of the following as the appropriate type of national indicator for the address structure:

national
international

Usage Guidelines

Select the international indicator to be used for out-going addresses.

Example

ni-indicator international

point-code

Selects and configures the SS7-type point code for use with the out-going address.

Product

SGSN

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > GTT Address-Map Configuration > Out-Address Configuration

configure > gtt address-map map_id > out-address address_name

Entering the above command sequence results in the following prompt:

[local]host_name(config-gtt-addrmap-outaddr-out_address)#

Syntax

point-code pt_code

pt_code

Enter 1 to 11 digits in the point code format predefined during variant selection of GTT association.

Usage Guidelines

Define an ITU point code to be used for out-going address processing.

Example

point-code 6.255.6

routing-indicator

Selects the type of routing and the indicator to be included in the out-going message.

Product

SGSN

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > GTT Address-Map Configuration > Out-Address Configuration

configure > gtt address-map map_id > out-address address_name

Entering the above command sequence results in the following prompt:

[local]host_name(config-gtt-addrmap-outaddr-out_address)#

Syntax

routing-indicator routing_ind

routing_ind

Select one of the following options:

gt : Inserts an indicator that identifies routing based on global title.
ssn : Inserts an indicator that identifies routing based on the subsystem number.

Usage Guidelines

Select global title as the appropriate routing indicator.

Example

routing-indicator gt

ssf

Selects the subservice field as factor in the out-going address processing. ssf sets the network indicator in the subservice field for SS7 Message Signal Units (MSUs). The indicator carried in the message's routing information typically identifies the structure of the point code as a message from within a nation or as a message coming from outside the national - international.

Product

SGSN

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > GTT Address-Map Configuration > Out-Address Configuration

configure > gtt address-map map_id > out-address address_name

Entering the above command sequence results in the following prompt:

[local]host_name(config-gtt-addrmap-outaddr-out_address)#

Syntax

ssf sub_svc_fld

sub_svc_fld

Select one of the following options:

international: The network indicator identifies the message as international with a point code structure that does not match the national point code structure,
national: The network indicator identifies the messages as having a national point code structure.
reserved: Provides an alternate network indicator for national messages.
spare: Provides an alternate network indicator for international messages.

Usage Guidelines

Select the international NI for inclusion in out-going address subservice fields.

Example

ssf international

ssn

Selects the subsystem number to be included in the out-going message.

Product

SGSN

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > GTT Address-Map Configuration > Out-Address Configuration

configure > gtt address-map map_id > out-address address_name

Entering the above command sequence results in the following prompt:

[local]host_name(config-gtt-addrmap-outaddr-out_address)#

Syntax

ssn sub_sys_num

sub_sys_num

Enter an integer from 1 to 255.

Usage Guidelines

Use subsystem number 44 in the out-going address.

Example

ssn 44

Was this Document Helpful?

Feedback

Contact Cisco

Open a Support Case
(Requires a Cisco Service Contract)