Command Line Interface Reference, Modes C - D, StarOS Release 21.25

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents

Find Matches in This Book

Results

Updated:: September 30, 2021

Chapter: DSCP Template Configuration Mode Commands

DSCP Template Configuration Mode Commands
control-packet
end
exit
data-packet

DSCP Template Configuration Mode Commands

Mode

The DSCP Template Configuration Mode provides the commands to configure DSCP marking for control packets and data packets for Gb over IP. Any number of DSCP templates can be generated in the SGSN Global configuration mode and then a template can be associated with one or more GPRS Services via the commands in the GPRS Service configuration mode.

Exec > Global Configuration > SGSN Global Configuration > DSCP Template Configuration

configure > context context_name > sgsn-global > dscp-template template_name

Entering the above command sequence results in the following prompt:

[local]host_name(config-dscp-template-template_name)#

Important

The commands or keywords/variables that are available are dependent on platform type, product version, and installed license(s).

control-packet

Configures the diffserv code point marking (DSCP) value for 3GPP quality of service (QoS) class downlink control packets.

Important

In Release 20 and later, HNBGW is not supported. This command must not be used for HNBGW in Release 20 and later. For more information, contact your Cisco account representative.

Product

HNB-GW

SGSN

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > SGSN Global Configuration > DSCP Template Configuration

configure > context context_name > sgsn-global > dscp-template template_name

Entering the above command sequence results in the following prompt:

[local]host_name(config-dscp-template-template_name)#

Syntax

control-packet qos-dscp { af11 | af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 | af43 | be | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef } 
 default control-packet

default

Resets the quality of service (QoS) DSCP setting to the 'BE' (best effort) default value.

`DSCP marking option`

Select one of the following downlink DSCP options for the control packets:


af11: Assured Forwarding 11 per-hop-behavior (PHB)	be: Best Effort for Forwarding
af12: Assured Forwarding 12 PHB	cs1: Class Selector 1 PHB
af13: Assured Forwarding 13 PHB	cs2: Class Selector 2 PHB
af21: Assured Forwarding 21 PHB	cs3: Class Selector 3 PHB
af22: Assured Forwarding 22 PHB	cs4: Class Selector 4 PHB
af23: Assured Forwarding 23 PHB	cs5: Class Selector 5 PHB
af31: Assured Forwarding 31 PHB	cs6: Class Selector 6 PHB
af32: Assured Forwarding 32 PHB	cs7: Class Selector 7 PHB
af33: Assured Forwarding 33 PHB	ef: Expedited forwarding PHB
af41: Assured Forwarding 41 PHB
af42: Assured Forwarding 42 PHB
af43: Assured Forwarding 43 PHB

Usage Guidelines

This command configures the QoS DSCP marking type for downlink control packets.

Related commands for SGSN:

To create/delete a DSCP template, use the dscp-template in the SGSN Global configuration mode (see the SGSN Global Configuration Mode Commands section).
To associated a specpific DSCP template with a specific GPRS service configuration, use the associate-dscp-template downlink documented in the GPRS Service Configuration Mode Commands section.
To check values configured for DSCP templates, use the show sgsn-mode command documented in the Exec Mode Commands section.

Related commands for HNB-GW:

To create/delete a DSCP template, use the dscp-template in the SGSN Global Configuration Mode .
To associated a specpific DSCP template with a system for a PSP instance in SS7 routing domain, use associate-dscp-template downlink documented in the SGSN PSP Configuration Mode Commands section.

Example

Use a command similar to the following to set expedited forward per-hop behavior for the downlink control packets:

control-packet qos-dscp ef

Use the following command to reset the default best effort per-hop behavior:

default control-packet

end

Exits the current configuration mode and returns to the Exec mode.

Product

All

Privilege

Security Administrator, Administrator

Syntax

end

Usage Guidelines

Use this command to return to the Exec mode.

exit

Exits the current mode and returns to the parent configuration mode.

Product

All

Privilege

Security Administrator, Administrator

Syntax

exit

Usage Guidelines

Use this command to return to the parent configuration mode.

data-packet

Configures the diffserv code point marking (DSCP) value for 3GPP quality of service (QoS) class downlink data packets.

Product

SGSN

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > SGSN Global Configuration > DSCP Template Configuration

configure > context context_name > sgsn-global > dscp-template template_name

Entering the above command sequence results in the following prompt:

[local]host_name(config-dscp-template-template_name)#

Syntax

control-packet { background | conversationa | interactive { priority1 | priority2 | priority3 } | streaming } qos-dscp { af11 | af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 | af43 | be | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef } 
default data-packet { background | conversationa | interactive { priority1 | priority2 | priority3 } | streaming }

default

Resets the quality of service (QoS) DSCP setting to the be (best effort) default value.

background | conversationa | interactive | streaming

Select the QoS traffic class of service for the downlink data packets.

priority1 | priority2 | priority3

Select the traffic handling priority to be applied to the specified traffic class.

`DSCP option`

Select one of the following DSCP settings for the selected traffic class. Default is best effort (be ) for all traffic classes settings.


af11: Assured Forwarding 11 per-hop-behavior (PHB)	be: Best Effort for Forwarding
af12: Assured Forwarding 12 PHB	cs1: Class Selector 1 PHB
af13: Assured Forwarding 13 PHB	cs2: Class Selector 2 PHB
af21: Assured Forwarding 21 PHB	cs3: Class Selector 3 PHB
af22: Assured Forwarding 22 PHB	cs4: Class Selector 4 PHB
af23: Assured Forwarding 23 PHB	cs5: Class Selector 5 PHB
af31: Assured Forwarding 31 PHB	cs6: Class Selector 6 PHB
af32: Assured Forwarding 32 PHB	cs7: Class Selector 7 PHB
af33: Assured Forwarding 33 PHB	ef: Expedited forwarding PHB
af41: Assured Forwarding 41 PHB
af42: Assured Forwarding 42 PHB
af43: Assured Forwarding 43 PHB

Usage Guidelines

This command configures the QoS DSCP marking type for downlink data packets. DSCP levels indicate how packets are to be handled

Related commands:

To create/delete a DSCP template, use the dscp-template in the SGSN Global configuration mode (see the SGSN Global Configuration Mode Commands section).
To associated a specpific DSCP template with a specific GPRS service configuration, use the associate-dscp-template downlink documented in the GPRS Service Configuration Mode Commands section.
To check values configured for DSCP templates, use the show sgsn-mode command documented in the Exec Mode Commands section.

Example

Use a command similar to the following to set expedited forward per-hop behavior for the downlink control packets:

control-packet qos-dscp ef

Use the following command to reset the default best effort per-hop behavior:

default control-packet

Was this Document Helpful?

Feedback

Contact Cisco

Open a Support Case
(Requires a Cisco Service Contract)