Traffic Policy Group Configuration Mode Commands

Policy-Group is used to form a set of configured Policy-Maps for the Traffic Policy feature. Multiple policies can be applied for a subscriber session flow within a destination context.

Mode

Exec > Global Configuration > Context Configuration > Traffic Policy Group Configuration

configure > context context_name > policy-group name group_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-policy-group)#

Important

The commands or keywords/variables that are available are dependent on platform type, product version, and installed license(s).

3gpp2 data-over-signaling

Configures 3GPP2-related flow treatment policy for the flow-based traffic policing of subscriber sessions.

Product

HA

HSGW

PDSN

P-GW

SAEGW

SCM

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Context Configuration > Traffic Policy Map Configuration

configure > context context_name > policy-map name map_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-policy-map)#

Syntax

3gpp2 data-over-signaling marking [ class-map class_name ] 
no 3gpp2 data-over-signaling marking

no

Disables configured 3GPP2-related flow treatment policy.

class-map class_name

Associates class map to be used for selective data over signaling (DOS) marking. class_name is an alphanumeric string of 1 through 15 characters.

marking

Indicates 3GPP2-related traffic flow for data over signaling channel.

Usage Guidelines

Use this command to mark traffic flows for 3GPP2-related policy.

Example

3gpp2 data-over-signaling marking

access-control

Configures the access control action for traffic flows matching the Class-Map rules.

Product

ASN-GW

HA

HSGW

PDSN

P-GW

SAEGW

SCM

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Context Configuration > Traffic Policy Map Configuration

configure > context context_name > policy-map name map_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-policy-map)#

Syntax

access-control { allow | discard }

allow

Allows the packets, if the policy matches with the criteria defined in the Class-Map assigned to the specific traffic policy.

discard

Discards the packets, if the policy matches with the criteria defined in the Class-Map assigned to the specific traffic policy.

Usage Guidelines

Configures the action or treatment for traffic flows match criteria specified in the assigned Class-Map.

Example

The following command allows the packets or traffic flow on matching with criteria specified in assigned Class-Map for specific traffic policy. 
access-control allow

accounting suppress

Suppresses accounting action for traffic flows matching the policy map.

Product

ASN-GW

HA

HSGW

PDSN

P-GW

SAEGW

SCM

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Context Configuration > Traffic Policy Map Configuration

configure > context context_name > policy-map name map_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-policy-map)#

Syntax

[ no ] accounting suppress

no

Removes the suppression of accounting for traffic flow matching this policy map.

Usage Guidelines

Use this command to suppress accounting action on traffic flow matching this policy map.

Policy maps configured for accounting suppression are used to implement the QChat Billing Suppression feature that selectively starts and terminates accounting sessions based on the categorization of traffic as being interesting or non-interesting. See the accounting trigger command.

Example

The following command configures suppression of accounting on traffic flows matching this policy map: 
accounting suppress

accounting trigger

Configures an accounting trigger policy map to selectively start and terminate accounting sessions based on the categorization of traffic as being interesting or non-interesting. This command supports the QCHAT Billing Suppression feature.

Product

HSGW

PDSN

P-GW

SAEGW

SCM

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Context Configuration > Traffic Policy Map Configuration

configure > context context_name > policy-map name map_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-policy-map)#

Syntax

[ no | default ] accounting trigger { inactivity-timeout | interesting-traffic | intra-service-handoff }

default

Sets or restores the default value assigned for specified parameter.

no

Disables previously configured triggers.

inactivity-timeout

Generates an accounting Stop message if there has been no data activity on the session for the interim accounting timeout interval.

Default: disabled

interesting-traffic

Generates an accounting Start message upon arrival of interesting traffic.

Default: disabled

intra-service-handoff

Generates accounting Start and Stop messages during intra-service handoffs.

Default: enabled

If disabled, the messages are suppressed during the handoffs. The current accounting session continues and no Stop or Start messages are generated during the intra-service handoff.

Usage Guidelines

Use this command to configure an accounting trigger policy map (ATPM) to selectively start and terminate accounting sessions based on the categorization of traffic as being interesting or non-interesting. This command supports the QChat Billing Suppression feature.

Interesting traffic is identified as traffic that does not match any of the other Accounting Policy Maps (APMs) configured for accounting suppression. See the accounting suppress command.

An ATPM is similar to an APM, but without the class map rules. The ATPM is configured as of type accounting using the type accounting command.

Optionally, timeout can be triggered when there is no data traffic for the interim accounting timeout interval using the accounting trigger inactivity-timeout stop command. On timeout, the accounting session is terminated and an Accounting Stop message is sent. A new accounting session is created if interesting traffic resumes.

In the ATPM, the trigger to start accounting for interesting traffic is configured using the accounting trigger interesting-traffic command. Accounting Start is triggered on arrival of interesting traffic, or change in airlink parameters conveyed through active-start airlink record. If an active-start record was included in the initial connection setup, Accounting Start is not triggered. But if the active-start comes separately and is the first one for the session, it is treated as airlink change and an Accounting Start is sent.

The ATPM should have the lowest precedence among the APMs.

As the airlink events are generated on the ingress side, the ATPM must be included in a policy group that is applied to the ingress direction in the subscriber profile. The configuration is applicable only for standard trigger policy and session based accounting mode.

Example

The following command sets the trigger to generate accounting start message upon arrival of interesting traffic: 
accounting trigger interesting-traffic

class-map

Assigns a traffic classification rule (Class-Map) to the policy map.

Product

ASN-GW

HA

HSGW

PDSN

P-GW

SAEGW

SCM

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Context Configuration > Traffic Policy Map Configuration

configure > context context_name > policy-map name map_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-policy-map)#

Syntax

[ no ] class-map name

no

Enables or disables class-map .

name

Specifies the name of the class map assigned for this policy map. The class map should have been preconfigured via the Class Map Configuration Mode.

name must be an alphanumeric a string of 1 through 15 characters.

Usage Guidelines

Use this command to assign a class map to the policy map for traffic policing. The class map is configured in the Class Map Configuration Mode.

Example

The following command assigns the class map classification1 to the current policy map: 
class classification1

description

Allows you to enter descriptive text for this configuration.

Product

All

Privilege

Security Administrator, Administrator

Syntax

description text 
no description

no

Clears the description for this configuration.

text

Enter descriptive text as an alphanumeric string of 1 to 100 characters.

If you include spaces between words in the description, you must enclose the text within double quotation marks (" "), for example, "AAA BBBB".

Usage Guidelines

The description should provide useful information about this configuration.

do show

Executes all show commands while in Configuration mode.

Product

All

Privilege

Security Administrator, Administrator

Syntax

do show

Usage Guidelines

Use this command to run all Exec mode show commands while in Configuration mode. It is not necessary to exit the Config mode to run a show command.

The pipe character | is only available if the command is valid in the Exec mode.


Caution

There are some Exec mode show commands which are too resource intensive to run from Config mode. These include: do show support collection , do show support details , do show support record and do show support summary . If there is a restriction on a specific show command, the following error message is displayed: 

Failure: Cannot execute 'do	show support' command from Config mode.

end

Exits the current configuration mode and returns to the Exec mode.

Product

All

Privilege

Security Administrator, Administrator

Syntax

end

Usage Guidelines

Use this command to return to the Exec mode.

exit

Exits the current mode and returns to the parent configuration mode.

Product

All

Privilege

Security Administrator, Administrator

Syntax

exit

Usage Guidelines

Use this command to return to the parent configuration mode.

flow-tp-trigger

This command specifies that the traffic volume will be calculated based on the traffic on the flow.

Product

ASN-GW

HA

HSGW

PDSN

P-GW

SAEGW

SCM

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Context Configuration > Traffic Policy Map Configuration

configure > context context_name > policy-map name map_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-policy-map)#

Syntax

flow-tp-trigger volume traffic_volume_threshold 
no flow-tp-trigger volume

traffic_volume_threshold

Specifies the volume threshold to trigger traffic policing. volume must be an integer from 1 through 4294967295.

Usage Guidelines

This command is available if you have purchased and installed the Intelligent Traffic Control License on your system. Use this command to calculate the traffic volume based on the traffic on the flow.

Example

flow-tp-trigger volume 500

ip header-compression

Enables the system to mark IP flows for Robust Header Compression (RoHC).

Product

ASN-GW

HA

HSGW

PDSN

P-GW

SAEGW

SCM

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Context Configuration > Traffic Policy Map Configuration

configure > context context_name > policy-map name map_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-policy-map)#

Syntax

[ no ] ip header-compression rohc flow-marking

no

Disables the setting.

rohc flow-marking

Marks the IP flow for SO67 and PPP RoHC.

Usage Guidelines

Use this command to mark IP flows for SO67 and PPP RoHC.

Example

ip header-compression rohc flow-marking

qos encaps-header

Enables and configures Quality of Service (QoS) policy to use Differentiated Service Code Point (DSCP) marking in IP header fields for the flow-based traffic policing to subscriber session flow.

Product

ASN-GW

HA

HSGW

PDSN

P-GW

SAEGW

SCM

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Context Configuration > Traffic Policy Map Configuration

configure > context context_name > policy-map name map_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-policy-map)#

Syntax

qos encaps-header dscp-marking { dscp_code | copy-from-user-datagram [ ignore-pcf-signaled-dscp ] | user-datagram }  
no qos encaps-header dscp-marking { dscp_code | copy-from-user-datagram [ ignore-pcf-signaled-dscp ] }

no

Enables/Disables the qos encaps-header .

The value must be expressed as a hexadecimal value from 0x00 through 0x3F.

dscp-marking dscp_code

Uses the DSCP code value marked in the IP header of packet/flow to determine the QoS for traffic policing. dscp_code must be expressed as a hexadecimal number from 0x00 through 0x3F.

copy-from-user-datagram

Uses the DSCP code value from the user datagram (UDP header) to determine the QoS for traffic policing.

ignore-pcf-signaled-dscp

Overrides the highest priority DSCP value signaled by the PCF.

user-datagram

Uses the DSCP value copied from the user datagram.

Usage Guidelines

Use this command to apply the QoS policy based on the DSCP value encapsulated in the IP packet header to police subscriber session traffic flows.


Important

For more information on the QoS traffic policing, see the System Administration Guide.

Example

The following command sets QoS policy with DSCP code value to 0x0C for Class 1, silver (AF12): 
qos encaps-header dscp-marking 0x0c

qos traffic-police

Enables and configures Quality of Service (QoS) policy for flow-based traffic policing of subscriber session flows on a per-flow basis.

Product

ASN-GW

HA

HSGW

PDSN

P-GW

SAEGW

SCM

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Context Configuration > Traffic Policy Map Configuration

configure > context context_name > policy-map name map_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-policy-map)#

Syntax

qos traffic-police committed bps peak bps burst-size byte exceed-action { drop | lower-ip-precedence | allow } violate-action { drop | lower-ip-precedence | allow } 
no qos traffic-police

no

Enables/Disables the qos traffic-police


Important

This parameter should be configured to be greater than the following two values: 1) three times greater than packet MTU for the subscriber connection, OR 2) three seconds worth of token accumulation within the "bucket" for the configured peak-data-rate.

burst-size bytes

Default: 3000

Specifies the allowed peak burst size in bytes. bytes must be an integer from 0 through 4294967295.


Important

This parameter should be configured to be greater than the following two values: 1) three times greater than the packet MTU for the subscriber connection, OR 2) three seconds worth of token accumulation within the "bucket" for the configured peak-data-rate.

committed bps

Default: 144000

Specifies the committed data rate (guaranteed-data-rate) in bits per second (bps).

bps must be an integer from 0 through 4294967295.

exceed-action { drop | lower-ip-precedence | allow }

Default: lower-ip-precedence

Specifies the action to take on packets that exceed the committed-data-rate but do not violate the peak-data-rate. The following actions are supported:

drop : Drops the packet

lower-ip-precedence : Transmits the packet after lowering the ip-precedence

allow : Transmits the packet

peak bps

Default: 256000

Specifies the peak data-rate for the subscriber in bits per second (bps).

bps must be an integer from 0 through 4294967295.

violate-action { drop | lower-ip-precedence | allow }

Default: drop

Specifies the action to take on the packets that exceed both the committed-data-rate and the peak-data-rate. The following actions are supported:

drop : Drops the packet

lower-ip-precedence : Transmits the packet after lowering the IP precedence

allow : Transmits the packet

Usage Guidelines

Use this command to apply the QoS policy to a subscriber session flow for flow-based traffic policing.


Important

For additional information on the QoS traffic policing, see the System Administration Guide.

Example

The following command sets the committed data rate to 102400 bps with a peak data rate of 128000 bps and a burst size of 2048 bytes. This lowers the IP precedence when the committed-data-rate is exceeded and drops the packets when the peak-data-rate are violated: 
qos traffic-police commited 102400 peak 128000 burst-size 2048 exceed-action lower-ip-precedence violate-action drop

qos user-datagram dscp-marking

Enables and configures Quality of Service (QoS) policy related to differentiated service code point (DSCP) marking in the user datagrams of subscriber session flows on a per-flow basis.

Product

ASN-GW

HA

HSGW

PDSN

P-GW

SAEGW

SCM

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Context Configuration > Traffic Policy Map Configuration

configure > context context_name > policy-map name map_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-policy-map)#

Syntax

qos user-datagram dscp-marking dscp_code 
no qos user-datagram dscp-marking

dscp_code

Specifies the use of the DSCP code value marked in the IP header of packet/flow to determine the QoS for traffic policing. dscp_code must be expressed as a hexadecimal number from 0x00 through 0x3F.

Usage Guidelines

Use this command to apply the QoS policy to subscriber session flow by DSCP marking in user datagram.

Example

The following command sets DSCP marking for user datagram as 0x01 for QoS to subscriber session flow: 
qos user-datagram dscp-marking 0x01

sess-tp-trigger

Configures the trigger for traffic policing based on the traffic volume for a subscriber session.

Product

ASN-GW

HA

HSGW

PDSN

P-GW

SAEGW

SCM

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Context Configuration > Traffic Policy Map Configuration

configure > context context_name > policy-map name map_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-policy-map)#

Syntax

sess-tp-trigger volume volume direction { both | downlink | uplink } 
no sess-tp-trigger

no

Enables or disables the sess-tp-trigger

volume

Specifies the traffic volume threshold (in bytes) that triggers traffic control. volume is an integer from 1 through 4294967295.

Usage Guidelines

Use this command to trigger traffic control based on the traffic volume for a subscriber session. This command requires the purchase and installation of a license.

Example

sess-tp-trigger 500

type

Specifies the type of traffic policy within a specific Policy-Map.

Product

ASN-GW

HA

HSGW

PDSN

P-GW

SAEGW

SCM

Privilege

Administrator

Mode

Exec > Global Configuration > Context Configuration > Traffic Policy Map Configuration

configure > context context_name > policy-map name map_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-policy-map)#

Syntax

type { accounting | dynamic { three-gpp2 rev-A profile-id { any | id profile_id | range low_value to high_value } flow-id { any | id flow_id | range low_value to high_value } | pre-provisioned wimax asn-service-profile-id { any | id service_id } asn-pdfid { any | id pdf_id } | static | template }

accounting

Specifies the type of traffic policing as accounting for this specific policy map. This configuration is used for enabling/disabling the accounting of different flows matching conditions within this Policy-Map.

dynamic

Identifies the type of policy map as dynamic.

three-gpp2 rev-A

Configures the dynamic policy map type for CDMA2000-3GPP2 RevA service.

profile-id { any | id profile_id | range low_hex to high_hex }

Specifies the profile id matching within this policy map.

any : allows any profile identifier matching this policy map.

id profile_id : allows specific profile identifier matching with in this policy map. profile_id must be a hexadecimal number from 0x0 to 0xFFFF.

range low_value to high_value : identifies a range in which a profile identifier must fall within to be considered a match. low_value and high_value must be either a hexadecimal number from 0x0 to 0xFFFF, or an integer from 0 through 65535 characters.

flow-id { any | id flow_id | range low_hex to high_hex }

Specifies the flow id matching in this policy map.

any allows any flow identifier matching with in this policy map.

id flow_id allows specific flow identifier matching with in this policy map. flow_id must be either a a hexadecimal number from 0x0 to 0xFFFF, or an integer from 0 to 65535.

range low_value to high_value : identifies a range in which a flow identifier must fall within to be considered a match. low_value and high_value must be either a hexadecimal number from 0x0 to 0xFFFF, or an integer 0 to 65535.

pre-provisioned

Identifies the type of policy map as pre-provisioned.

wimax

Configures WiMAX service policy map in an ASN-GW service.

asn-service-profile { any | id service_id }

Specifies the ASN Service profile identifier to match with in this policy map.

any : Allows any ASN Service Profile Identifier matching within this policy map.

id service_id : Allows specific Service Profile matching to a specified identifier. service_id must be an integer from 1 to 65535 that matches a service ID that was configured in the Subscriber Configuration Mode.

asn-pdfid { any | id pdf_id }

Specifies the ASN Packet Data Flow Identifier to match with in this policy map.

any : Allows any ASN Packet Data Flow Identifier matching within this policy map.

id pdf_id : Allows specific Packet Data Flow matching to a specified identifier. pdf_id must be an integer from 1 to 255 that matches a PDF ID that was configured in the Subscriber Configuration Mode.

static

Specifies the type of traffic policing as static for this specific Policy Map. In this type of policy, the traffic flow classification and flow treatment is pre-defined with classification rules through Class-Map configuration.

This is the detailed type of policy map.

template

Specifies the type of traffic policy to as a template to all subscribers associated with this policy map.

Usage Guidelines

Specifies the type of traffic policy within the specific Policy-Map.

Example

The following commands configures the traffic policy for this Policy-Map as static: 
type static
The following commands configures the traffic policy for this Policy-Map as pre-provisioned for WiMAX service requiring a match of any service profile and PDF id of 3 : 
type pre-provisioned wimax asn-service-profile any asn-pdfid id 3