Configures to accept VPN prefixes with Router Distinguisher (RD) value having Administrator Subfield, which is an Autonomous System number 0.

no

Removes the configured VPN prefixes with RD value having AS number 0.

Enters the IPv4 Address Family configuration mode. Optionally, it also enables the Virtual Routing and Forwarding (VRF) routing configuraiton, if specified.

no

Removes the configured IPv4 address family VRF mode.

address-family ipv4

Enters the BGP Address-Family IPv4 mode to allow entry of IPv4 BGP parameters.

Important

The route distinguisher ID must be configured for the VRF name via the route-distinguisher command in BGP VRF Configuration mode, before using this keyword.

vrf vrf_name

Enables the exchange of VRF routing information. When this keyword is specified with this command, the address family mode changes to VRF address family mode. vrf_name is the name of an existing VFR expressed as an alphanumeric string of 1 through 63 characters.

Enters the IPv6 Address Family configuration mode. Optionally, it also enables the Virtual Routing and Forwarding (VRF) routing configuration mode, if specified.

no

Removes the configured IPv6 address family VRF mode.

address-family ipv6

Enters the BGP Address-Family IPv6 mode to allow entry of IPv6 BGP parameters.

vrf vrf_name

Enables the exchange of VRF routing information. When this keyword is specified with this command, the address family mode changes to VRF address family mode. vrf_name is the name of an existing VFR expressed as an alphanumeric string of 1 through 63 characters.

Enters the IPv4 VPN Address Family configuraiton mode.

address-family vpnv4

Enters the BGP Address-Family IPv4 VPN mode to allow entry of VPN BGP parameters.

Enters the IPv6 VPN Address Family configuraiton mode.

address-family vpnv6

Enters the BGP Address-Family IPv6 VPN mode to allow entry of VPN BGP parameters.

Defines the BGP-specific parameters regarding graceful restarts.

graceful-restart restart-time rest_time

Specifies the maximum time (in seconds) required for neighbor(s) to gracefully restart. rest_time must be an integer from 1 through 3600.

graceful-restart stalepath-time stale_time

Specifies the maximum time (in seconds) to retain stale paths from restarting neighbor(s). stale_time must be an integer from 1 through 3600.

graceful-restart update-delay rest_time

Specifies the maximum time (in seconds) to defer initial route-selection. update-delay must be an integer from 1 through 3600.

Allows you to enter descriptive text for this configuration.

no

Clears the description for this configuration.

text

Enter descriptive text as an alphanumeric string of 1 to 100 characters.

If you include spaces between words in the description, you must enclose the text within double quotation marks (" "), for example, "AAA BBBB".

Defines the administrative distance for routes. The administrative distance is the default priority for a specific route or type route.

no

Removes the specified administrative distance for the specific route.

distance admin distance prefix prefix_addr [ route-access-list list_name ]

Sets the administrative distance to a specified value for routes with a specific IP prefix. If you also specify a route access list, the IP prefix must match the rules of that access list.

admin distance : Specifies the administrative distance that you want to apply to the IP prefix. distance must be an integer from 1 through 254.

prefix prefix_addr : Specifies the IP prefix of routes that should have the admin distance applied. prefix_addr must be an IPv4 address in dotted-decimal notation and the number of subnet bits, representing the subnet mask in CIDR shorthand (for example, 209.165.200.225/24).

route-access-list list_name : Defines the name of a route access list that defines for which routes the administrative distance should be set.

distance bgp external ebgp_dist internal ibgp_dist local local_dist

Sets the administrative distance for external (eBGP), internal (iBGP) and local routes.

external ebgp_dist : Sets the administrative distance for eBGP routes. ebgp_dist must be an integer from 1 through 254.

internal ibgp_dist : Sets the administrative distance for iBGP routes. ibgp_dist must be an integer from 1 through 254.

local local_dist : Sets the administrative distance for local routes. local_dist must be an integer from 1 through 254.

Exits the current configuration mode and returns to the Exec mode.

Enforces the first Autonomous System (AS) for Exterior Border Gateway Protocol (eBGP) routes. An AS is a connected group of one or more Internet Protocol prefixes run by one or more network operators which has a single and clearly defined routing policy (RFC 1930).

no

Disables the enforcement of the first AS for Exterior Border Gateway Protocol (eBGP) routes.

enforce-first-as

Enables the enforcement of the first AS for Exterior Border Gateway Protocol (eBGP) routes.

Exits the current mode and returns to the parent configuration mode.

Adds a preconfigured IP VRF context instance to the BGP ASN and configures the BGP attributes and related parameters to the VRF. This command also switches the command mode to BGP VRF Configuration mode.

no

Removes an associated IP VRF from specified BGP AS number and other configured parameters.

vrf_name

Specifies the IP VRF context configured in the Context configuration mode and to be associated with a BGP AS number. vrf_name must be an alphanumeric string of 1 through 79 characters identifying an existing instance.

Enables forwarding packets over multiple paths and specifies the maximum number of external BGP (eBGP) or internal BGP (iBGP) paths between neighbors.

no

Disables forwarding packets over multiple eBGP or iBGP paths between neighbors.

ebgp max_num

Enables forwarding packets over multiple eBGP paths between neighbors and specifies the maximum number of eBGP paths. max_num must be an integer from 1 through 10, or 1 through 32 (VPC-DI only), or 1 through 64 (VPC-DI only, Release 21.4+).

ibgp max_num

Enables forwarding packets over multiple iBGP paths between neighbors and specifies the maximum number of iBGP paths. max_num must be an integer from 1 through 10, or 1 through 32 (VPC-DI only), or 1 through 64 (VPC-DI only, Release 21.4+).

Configures BGP routers that interconnect to non-broadcast networks. Note that a remote AS number must be specified for a neighbor before other parameters can be configured.

no

Delete the specified parameter from the router configuration.

neighbor ip_address

Specifies the IP address of a BGP neighbor. ip_address must be in IPv4 dotted-decimal or IPv6 colon-separated-hexadecimal notation.

activate

Enable the exchange of routes with this neighbor.

advertisement-interval adv_time

The minimum interval (in seconds) between sending BGP routing updates. adv_time must be an integer from 0 through 600. Default: 30

Note

The advertisement-interval must be explicitly configured for an address-family so that it can take effect for that address-family. By default it will be applicable only for the IPv4 address-family. Specify the address family via the address-family command. You can then set the neighbor advertisement-interval in the address family configuration mode.

capability graceful-restart

Configures BGP graceful restart attributes.

default-originate [ route-map map_name ]

Enables the origination of default routes to this neighbor

route-map map_name : Specifies the route-map that contains the criteria to originate default routes. map_name must be the name of an existing route-map in the current context.

distribute-list dist_list { in | out }

Filters updates to and from this neighbor based on a route access list. dist_list : The name or number of an existing route-access-list. Default: No filtering is performed.

in : Indicates that incoming advertised routes should be filtered.

out : Indicates that outgoing advertised routes should be filtered.

ebgp-multihop [ max-hop number ]

Allows EBGP neighbors that are not on directly connected networks.

[ max-hop ] number : Specifies the maximum number of hops allowed to reach a neighbor. number must be an integer from 1 through 255. Default hop count: 255

encrypted password encrypted password

Specifies an encrypted password that is used only inside configuration files. This should be an alphanumeric string of 1 through 523 characters.

fall-over bfd [ multihop ] [ associate ]

Enables Bidirectional Fowarding Detection (BFD) multihop support for fallover.

This command adds or modifies a session in BFD for the BGP peer. If there is an existing session in BFD (same source-address/destination address), BGP or OSPF protocol will be added to the list of clients for the BFD session. BGP or OSPF will then be notified when there is a change in the BFD session state.

If there is no such BFD session, a new session is added in BFD. For MH-BFD, the session inherits the parameters including min-tx, min-rx, multiplier and authentication from the multihop-peer configuration in BFD by matching the destination address. If the parameters (interval) are not configured in BFD, then the BFD session will be in Admin-down state.

BGP adds a session in BFD only when the BGP peer is Established state. If there is a state transition in bgp where the peer is no longer in established state, then the bfd session is deleted. It will be added again, once the peer comes back to Established state.

When used, the associate keyword associates BGP and BFD neighbors. BGP peers come up only when the BFD session is up.

filter-list filt_list { in | out }

Establishes BGP filters based on an AS path access list. filt_list is the name of an existing AS path access list.

in : Indicates that incoming advertised routes will be filtered.

out : Indicates that outgoing advertised routes will be filtered.

max-prefix max_num [ threshold thresh_percent ] [ warning-only ]

The maximum number of prefixes accepted from this peer. When the maximum is exceeded the neighbor connection is reset.

Default: No maximum prefix limit.

max_num : Specifies the maximum number of prefixes permitted. This must be an integer from 1 through 4294967295.

[ threshold thresh_percent ] : Specifies a percentage value of when the BGP table is full. When this value is reached, peer warnings are sent to the neighbor and the neighbor connection is reset. thresh_percent must be an integer from 1 through 100.

[ warning-only ] : Specifies that only a warning message is sent when the limit is exceeded. The neighbor connection is not reset

next-hop-self

Disables the next hop calculation for this neighbor.

password password

Specifies a password that is only used inside configuration files. This should be an alphanumeric string of 1 through 24 characters.

remote-as AS_num

Specify the AS number of the BGP neighbor.

AS_num : Specifies the neighbor's AS number as an integer from 1 through 65535.

remove-private-AS

Removes the private AS number from outbound updates. Default: Do not remove the private AS number.

restart-time rest_time

Specifies the maximum time (in seconds) required for a neighbor to restart. rest_time must be an integer between 1 and 3600.

route-map map_name { in | out }

Applies a route map to the neighbor. map_name i s the name of an existing route-map in the current context.

in : Indicates that the route map applies to incoming advertisements.

out : Indicates that the route map applies to outgoing advertisements.

send-community { both | extended | standard }

Sends the community attributes to a peer router (neighbor).

both : Sends extended and standard community attributes.

extended : Sends extended community attributes.

standard : Sends standard community attributes.

shutdown

Administratively shuts down this neighbor. This disables exchanging routes or configuring parameters for this neighbor.

srp-activated-soft-clear

Enables BGP updates when Service Redundancy Protocol SRP-enabled resources are modified.

timers { [ connect-interval conn_time ] | [ keepalive-interval keep_time holdtime-interval hold_time ] }

Specifies BGP timers for this neighbor.

connect-interval conn_time : Specifies the connect timer in seconds. conn_time must be an integer from 0 through 65535. The default is 60 seconds.

keepalive-interval keep_time : The frequency (in seconds) at which the current BGP router sends keepalive messages to its neighbor. keep_time must be an integer from 0 through 65535. The default is 30 seconds.

Holdtime-interval hold_time : The interval (in seconds) the router waits for a keepalive message before declaring a neighbor dead. hold_time must be an integer from 0 through 65535. The default is 90 seconds.

update-source ip_address

Binds the specified IP address to the BGP socket that is used to communicate to the peer. ip_address is an IPv4 address in dotted-decimal notation.

In most cases you should set the update-source address to the address of the loopback interface in the current context. By doing this, the TCP connection does not go down until there is no route for the loopback address in the peering router.

weight value

Sets the default weight for routes from this neighbor. value must be an integer from 0 through 65535. Default: 0

Specifies a network to announce via BGP.

no

Delete the specified network from the configuration for the BGP router.

ip_address / mask

Specifies the IP address and netmask bits for the network to announce via BGP. ip_address is a network IPv4 address in dotted-decimal notation and mask is the number of subnet bits, representing a subnet mask in CIDR shorthand. These must be entered in the dotted-decimal notation/subnet bits format (for example, 209.165.200.234/24).

[ route-map map_name ]

Filter routes through the specified route map before announcing the network. map_name is the name of the route-map to use specified as an alphanumeric string of 1 through 79 characters.

Redistributes routes via BGP from another protocol to BGP neighbors.

no

Remove the specified redistribution parameters from the BGP router configuration.

redistribute connected

Specifies that connected routes will be redistributed.

redistribute ospf

Specifies that Open Shortest Path First (OSPF) routes will be redistributed

redistribute rip

Specifies that Routing Information Protocol (RIP) routes will be redistributed. (RIP is not supported at this time.)

redistribute static

Specifies that static routes will be redistributed.

[ route-map map_name ]

Filter routes through the specified route map before redistribution. map_name specifies the name of the route-map to use and must be specified as an alphanumeric string of 1 through 79 characters.

Overrides the configured router identifier and causes BGP peers to reset.

no

Remove the specified router ID from the router's configuration and use the default router ID.

router-id ip_address

Specifies the IP address to use as the BGP router ID as an IPv4 address in dotted-decimal notation.

Configures the BGP background scanner interval. BGP monitors the next hop of the installed routes to verify next-hop reachability and to select, install, and validate the BGP best path. By default, the BGP scanner polls the Routing Information Base (RIB) for this information every 60 seconds. During the 60-second time period between scan cycles, Interior Gateway Protocol (IGP) instabilities or other network failures can cause temporarily black holes and routing loops.

no

Remove the user specified scan time from the router's configuration. The scan time is reset to the default value.

scan-time time

Specifies the amount of time (in seconds) to wait between background scans to determine next-hop validity. time must be an integer from 5 through 60. Default: 60

Configures BGP routing timers.

no

Remove the user specified timer values from the router's configuration. The timer values are reset to the default values.

timers bgp keepalive-interval interval holdtime-interval time

keepalive-interval interval : Specifies the interval (in seconds) to wait between sending keepalive packets as an integer from 0 through 65535. Default: 30

holdtime-interval time : Specifies the interval (in seconds) after which the neighbor is considered dead if keepalive messages are not received as an integer from 0 through 65535.

[ min-peer-holdtime-interval time ]

Specifies the interval (in seconds) that is the minimum acceptable hold time from a neighbor as an integer from 0 through 65535. The default is 0 so that there is no restriction on the hold time received in an OPEN message from the peer.