By default for StarOS releases prior to 21.0 the system encrypts passwords using an MD5-based cipher (option A). These passwords also have a random 64-bit (8-byte) salt added to the password. The chassis key is used as the encryption key.

Setting a chassis key supports an encryption method where the decryption requires the knowledge of a "shared secret". Only a chassis with knowledge of this shared secret can access the passwords. To decipher passwords, a hacker who knew the chassis key would still need to identify the location of the 64-bit random salt value within the encryption.

Passwords encrypted with MD-5 will have "+A" prefixes in the configuration file to identify the methodology used for encrypting.

Important

The default is Algorithm B.

Specify an another type of encryption algorithm. The Global Configuration mode cli-encrypt-algorithm command allows an operator to configure the password/secret encryption algorithm. The default encryption/password algorithm for releases prior to 21.0 is MD-5 as described above (option A). A second password encryption algorithm (option B) uses AES-CTR-128 for encryption and HMAC-SHA1 for authentication. The encryption key protects the confidentiality of passwords, while the authentication key protects their integrity. For release 21.0 and higher Algorithm B is the default. Passwords encrypted with this key will have "+B" prefixes in the configuration file.

A third type of encryption algorithm can be specified (option C). This algorithm specifies the use of the HMAC-SHA512 cipher algorithm for encryption and authentication. Passwords encrypted with this key will have "+C" prefixes in the configuration file.

The encryption key is hashed from the chassis ID and a 16-byte Initialization Vector (IV) obtained from an internal random number generator. No two passwords are encrypted using the same encryption key/IV pair. The Security Administrator must set a chassis key in order to generate the chassis ID and resulting encryption key. A default chassis key based on a local MAC address is no longer supported.

The syntax for the cli-encrypt-algorithm command is:

config 
   cli-encrypt-algorithm { A | B | C }  

The system supports previously formatted encrypted passwords. The syntax of the encrypted passwords indicates which methodology was used for encryption. If the system does not see a prefix before the encrypted password, the earlier encryption method using a fixed key will be used. If the encrypted password includes the "+A" prefix, the decryption method uses the chassis key and random salt.

If the user saves a new configuration, the generated file will always contain passwords encrypted by the most recent method. The user cannot generate the earlier DES-based encryption values. However, all future StarOS releases will continue to support plain-text password entry for all two-way encryptable passwords

Refer to Configuring a Chassis Key in System Settings for additional information.

An external authenticating agent (such as RADIUS or Diameter) sends a list of LI server addresses as part of access-accept. For any intercept that was already installed or will be installed for that subscriber, a security check is performed to match the LI server address with any of the LI-addresses that were received from the authenticating agent. Only those addresses that pass this criteria will get the intercepted information for that subscriber.

While configuring a campon trigger, the user will not be required to enter the destination LI server addresses. When a matching call for that campon trigger is detected, a security check is done with the list received from the authentication agent. The LI-related information is only forwarded if a matching address is found.

When an active-only intercept is configured, if a matching call is found, a security check is made for the LI address received from the authentication agent and the intercept configuration will be rejected.

If no information related to LI server addresses is received for that subscriber, LI server addresses will not be restricted.

Important

A maximum of five LI server addresses are supported via an authenticating agent.

Important

The ability to restrict destination addresses for LI content and event delivery using RADIUS attributes is supported only for PDSN and HA gateways.

One LI administrator can access and/or modify the intercepts created by another LI administrator. Whenever an intercept is added, removed or modified, an event log is displayed across LI administrators about the change. An SNMP trap is also generated.

Users with low level authorization should not be able to create users with high level authorization. However, if a malicious actor were to be able to create a high level authorized user, they could then delete the other high level authorized users, thereby locking them out of the system.

Whenever a user's privilege level is increased or decreased, an SNMP notification will be sent out. A malicious actor may gain access to more privileged commands by somehow promoting" their privileges. Once this is done, they could then "demote" the privileges of all the other users, thereby locking the proper administrators out of the system.

The starLocalUserPrivilegeChanged trap indicates that a local user's privilege level has been changed.

The starOsShellAccessed trap indicates that a user has accessed the operating system shell.

To enable access to test-commands, a Security Administrator must log into the Global Configuration mode and enter cli hidden.

This command sequence is shown below.

[local]host_name# config 
[local]host_name(config)# cli hidden 
[local]host_name(config)# 

By default cli hidden is disabled.

A Security Administrator can set a plain-text or encrypted password for access to CLI test commands. The password value is stored in /flash along with the boot configuration information. The show configuration and save configuration commands will never output this value in plain text.

The Global Configuration mode command tech-support test-commands [encrypted] password new_password [ old-password old_password ] sets an encrypted or plain-text password for access to CLI test-commands.

This command sequence is shown below.

[local]host_name# config 
[local]host_name(config)# tech-support test-commands password new_password [ old-password old_password ] 
[local]host_name(config)# 

If the new password replaces an existing password, you must enter the old password for the change to be accepted.

If the old password is not entered or does not match the existing configured value, the following error message appears: "tech-support password is already configured". A prompt then appears to accept entry of the old password: "Enter old tech-support password:".

Entering old-password old_password allows you to replace the existing password without being prompted to enter the old password. If you incorrectly enter the old password or do not enter the old password, an error message appears: "Failure: Must enter matching old tech-support password to replace existing password".

The Quick Setup Wizard (Exec mode setup command) also prompts for entry of a tech-support test-commands password. If you have forgotten the old tech-support password, you can run setup directly from the Console port to enter a new tech-support password.

When a test-commands password is configured, the Global Configuration mode command cli test-commands [ encrypted ] password password requires the entry of the password keyword. If the encrypted keyword is specified, the password argument is interpreted as an encrypted string containing the password value. If the encrypted keyword is not specified, the password argument is interpreted as the actual plain text value

Important

If tech-support test-commands password is never configured, StarOS will create a new password. If the password keyword is not entered for cli test-commands, the user is prompted (no-echo) to enter the password. Also, cli hidden must be enabled by an administrator to access the CLI test-commands.

Exec mode commands are available to a privileged user who enters the command cli test-commands from Exec mode.

[local]host_name# cli test-commands [encrypted] password password 
Warning: Test commands enables internal testing and debugging commands 
USE OF THIS MODE MAY CAUSE SIGNIFICANT SERVICE INTERRUPTION 

Important

An SNMP trap (starTestModeEntered) is generated whenever a user enters CLI test-commands mode.

Configuration commands which provided access to low-level software parameters are accessible only after a privileged user enters the command cli test-commands from Global Configuration mode.

[local]host_name# config 
[local]host_name(config)# cli test-commands [encrypted] password password 
Warning: Test commands enables internal testing and debugging commands 
USE OF THIS MODE MAY CAUSE SIGNIFICANT SERVICE INTERRUPTION 

Important

An SNMP trap (starTestModeEntered) is generated whenever a user enters CLI test-commands mode.

CLI test-commands are not documented in the CLI Reference or other user documents. Lists of these Exec mode and Configuration mode commands/keywords are published in a separate document available through Cisco TAC. Detailed descriptions of the command/keyword functions are not provided. However, the user can refer to the CLI Help function for additional information.