- Preface
-
- Cisco Wireless Solution Overview
- Getting Started
- Managing Licenses
- Configuring 802.11 Bands
- Configuring 802.11 Parameters
- Configuring DHCP Proxy
- Configuring SNMP
- Configuring Aggressive Load Balancing
- Configuring Fast SSID Changing
- Configuring 802.3 Bridging
- Configuring Multicast
- Configuring Client Roaming
- Configuring IP-MAC Address Binding
- Configuring Quality of Service
- Configuring Application Visibility and Control
- Configuring Media and EDCA Parameters
- Configuring the Cisco Discovery Protocol
- Configuring Authentication for the Controller and NTP/SNTP Server
- Configuring RFID Tag Tracking
- Resetting the Controller to Default Settings
- Managing Controller Software and Configurations
- Managing User Accounts
- Managing Web Authentication
- Configuring Wired Guest Access
- Troubleshooting
-
- Overview of Ports and Interfaces
- Configuring the Management Interface
- Configuring the AP-Manager Interface
- Configuring Virtual Interfaces
- Configuring Service-Port Interfaces
- Configuring Dynamic Interfaces
- Configuring Ports
- Information About Using Cisco 5500 Series Controller USB Console Port
- Configuring Link Aggregation
- Configuring Multiple AP-Manager Interfaces
- Configuring VLAN Select
- Configuring Interface Groups
- Configuring Multicast Optimization
- High Availability
-
- Cisco Unified Wireless Network Solution Security
- Configuring RADIUS
- Configuring TACACS+
- Configuring Maximum Local Database Entries
- Configuring Local Network Users on the Controller
- Configuring Password Policies
- Configuring LDAP
- Configuring Local EAP
- Configuring the System for SpectraLink NetLink Telephones
- Configuring RADIUS NAC Support
- Using Management Over Wireless
- Using Dynamic Interfaces for Management
- Configuring DHCP Option 82
- Configuring and Applying Access Control Lists
- Configuring Management Frame Protection
- Configuring Client Exclusion Policies
- Configuring Identity Networking
- Configuring AAA Override
- Managing Rogue Devices
- Classifying Rogue Access Points
- Configuring Cisco TrustSec SXP
- Configuring Local Policies
- Configuring Cisco Intrusion Detection System
- Configuring IDS Signatures
- Configuring wIPS
- Configuring the Wi-Fi Direct Client Policy
- Configuring Web Auth Proxy
- Detecting Active Exploits
-
- Configuring WLANs
- Setting the Client Count per WLAN
- Configuring DHCP
- Configuring DHCP Scopes
- Configuring MAC Filtering for WLANs
- Configuring Local MAC Filters
- Configuring Timeouts
- Configuring the DTIM Period
- Configuring Peer-to-Peer Blocking
- Configuring Layer2 Security
- Configuring a WLAN for Static WEP
- Configuring Sticky Key Caching
- Configuring CKIP
- Configuring Layer 3 Security
- Configuring Captive Bypassing
- Configuring a Fallback Policy with MAC Filtering and Web Authentication
- Assigning a QoS Profile to a WLAN
- Configuring QoS Enhanced BSS
- Configuring Media Session Snooping and Reporting
- Configuring Key Telephone System-Based CAC
- Configuring Reanchoring of Roaming Voice Clients
- Configuring Seamless IPv6 Mobility
- Configuring Cisco Client Extensions
- Configuring Remote LANs
- AP Groups
- Configuring RF Profiles
- Configuring Web Redirect with 8021.X Authentication
- Configuring NAC Out-of-Band Integration
- Configuring Passive Clients
- Configuring Client Profiling
- Configuring Per-WLAN RADIUS Source Support
- Configuring Mobile Concierge
- Configuring Assisted Roaming
-
- Using Access Point Communication Protocols
- Searching for Access Points
- Configuring Global Credentials for Access Points
- Configuring Authentication for Access Points
- Configuring Embedded Access Points
- Converting Autonomous Access Points to Lightweight Mode
- Configuring Packet Capture
- OfficeExtend Access Points
- Using Cisco Workgroup Bridges
- Using Non-Cisco Workgroup Bridges
- Configuring Backup Controllers
- Configuring Failover Priority for Access Points
- Configuring AP Retransmission Interval and Retry Count
- Country Codes
- Optimizing RFID Tracking on Access Points
- Configuring Probe Request Forwarding
- Retrieving the Unique Device Identifier on Controllers and Access Points
- Performing a Link Test
- Configuring Link Latency
- Configuring the TCP MSS
- Configuring Power Over Ethernet
- Viewing Clients
- Configuring LED States for Access Points
- Configuring Access Points with Dual-Band Radios
-
- Mobility Groups
- Viewing Mobility Group Statistics
- Auto-Anchor Mobility
- Validating WLAN Mobility Security Values
- Using Symmetric Mobility Tunneling
- Running Mobility Ping Tests
- Configuring Dynamic Anchoring for Clients with Static IP Addresses
- Configuring Foreign Mappings
- Configuring Proxy Mobile IPv6
- Configuring New Mobility
- Index
Cisco Wireless Controller Configuration Guide, Release 7.6
Bias-Free Language
The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
- Updated:
- June 11, 2020
Feedback