Cisco Spaces

Cisco Spaces is the next generation indoor location services platform. The Network Mobility Services Protocol (NMSP) cloud-service of the wireless controller communicates with Cisco Spaces using HTTPS as a transport protocol.

Configuring Cisco Spaces

Follow the procedure given below to configure Cisco Spaces:

Before you begin

  • Configure DNS—To resolve fully qualified domain names used by NMSP cloud-services, configure a DNS using the ip name-server server_address configuration command as shown in Step 2.

  • Import 3rd party root CAs—The controller verifies the peer and the host based on the certificate that is sent by the CMX when a connection is established. However, root CAs are not preinstalled on the controller. You have to import a set of root CAs trusted by Cisco to the trustpool of the crypto PKI by using the crypto pki trustpool import url <url> configuration command as shown in Step 3.

  • A successful registration to Cisco Spaces is required to enable server url and server token parameters configuration which is needed to complete this setup.

Procedure

  Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

ip name-server namesvr-ip-addr

Example:

Device(config)#ip name-server 10.10.10.205

Configures the DNS on the controller to resolve the FQDN names used by the NMSP cloud-services.

Step 3

crypto pki trustpool import url url

Example:

Device(config)#crypto pki trustpool import url http://www.cisco.com/security/pki/trs/ios.p7b

Imports the 3rd party root CA. The controller verifies the peer using the imported certificate.

Step 4

[no] nmsp cloud-services server url url

Example:

Device(config)# nmsp cloud-services server url https://cisco.com

Configures the URL used for cloud services. Use the no form of the command to delete the server url from the configuration.

Step 5

[no] nmsp cloud-services server token token

Example:

Device(config)# nmsp cloud-services server token test

Configures the authentication token for the NMSP cloud service. Use the no form of the command to delete the server token from the configuration.

Step 6

[no] nmsp cloud-services http-proxy proxy-server port

Example:

Device(config)# nmsp cloud-services http-proxy 10.0.0.1 10

(Optional) Configures HTTP proxy details for the NMSP cloud service. Use the no form of the command to disable the use of a HTTP proxy.

Step 7

[no] nmsp cloud-services enable

Example:

Device(config)# nmsp cloud-services enable

Enables NMSP cloud services. Use the no form of the command to disable the feature.

Verifying Cisco Spaces Configuration

Use the following commands to verify the Cisco Spaces configuration.

To view the status of active NMSP connections, use the following command:

Device# show nmsp status

MSE IP Address   Tx Echo Resp  Rx Echo Req   Tx Data     Rx Data   Transport  
----------------------------------------------------------------------------
9.9.71.78        0             0             1           1         TLS
64.103.36.133    0             0             1230        2391      HTTPs

To view the NMSP cloud service status, use the following command:

Device# show nmsp cloud-services summary

CMX Cloud-Services Status
-------------------------

   Server:                                  https://yenth8.cmxcisco.com
   IP Address:                              64.103.36.133
   Cmx Service:                             Enabled
   Connectivity:                            https: UP
   Service Status:                          Active
   Last Request Status:                     HTTP/1.1 200 OK
   Heartbeat Status:                        OK

To view the NMSP cloud service statistics, use the following command:

Device# show nmsp cloud-services statistics

CMX Cloud-Services Statistics
-----------------------------

   Tx DataFrames:                                3213
   Rx DataFrames:                                1606
   Tx HeartBeat Req:                            31785
   Heartbeat Timeout:                               0
   Rx Subscr Req:                                2868
   Tx DataBytes:                                10069
   Rx DataBytes:                                37752
   Tx HeartBeat Fail:                               2
   Tx Data Fail:                                    0
   Tx Conn Fail:                                    0

To view the mobility services summary, use the following command:

Device# show nmsp subscription summary

Mobility Services Subscribed:
Index Server IP Services
----- --------- --------
1 209.165.200.225 RSSI, Info, Statistics, AP Monitor, AP Info
2 209.165.200.225 RSSI, Statistics, AP Info