Cisco Catalyst 9800 Series Wireless Controller Command Reference, Cisco IOS XE Cupertino 17.9.x

show aaa dead-criteria radius

To verify the dead-server-detection information for a RADIUS server, use the show aaa dead-criteria radius command.

show aaa dead-criteria radius ipaddr auth-port authport acct-port acctport

Syntax Description


`ipaddr`	IP address.
`authport`	Authentication port.
`acctport`	Accounting port.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Usage Guidelines

The show aaa dead-criteria radius ipaddr command displays output only if default ports are used. For non-default ports, use the show aaa dead-criteria radius ipaddr auth-port authport acct-port acctport command.

Examples

The following example shows how to see the dead-server-detection information for a RADIUS server with non-default authorization and accounting ports:

Device# show aaa dead-criteria radius 4.4.4.4 auth-port 4444 acct-port 3333

RADIUS: No server group specified. Using radius
RADIUS Server Dead Criteria:
=============================
Server Details:
Address : 4.4.4.4
Auth Port : 4444
Acct Port : 3333
Server Group : radius
Dead Criteria Details:
Configured Retransmits : 3
Configured Timeout : 5
Estimated Outstanding Access Transactions: 0
Estimated Outstanding Accounting Transactions: 0
Dead Detect Time : 10s
Computed Retransmit Tries: 10
Statistics Gathered Since Last Successful Transaction
=====================================================
Max Computed Outstanding Transactions: 0
Max Computed Dead Detect Time: 0s
Max Computed Retransmits : 0

The following example shows how to see the dead-server-detection information for a RADIUS server using default ports:

Device# show aaa dead-criteria radius 9.3.13.37

RADIUS: No server group specified. Using radius
RADIUS Server Dead Criteria:
=============================
Server Details:
Address : 9.3.13.37
Auth Port : 1812
Acct Port : 1813
Server Group : radius
Dead Criteria Details:
Configured Retransmits : 3
Configured Timeout : 30
Estimated Outstanding Access Transactions: 1
Estimated Outstanding Accounting Transactions: 0
Dead Detect Time : 10s
Computed Retransmit Tries: 10
Statistics Gathered Since Last Successful Transaction
=====================================================
Max Computed Outstanding Transactions: 4
Max Computed Dead Detect Time: 48s
Max Computed Retransmits : 30

show aaa servers

To display the status and number of packets that are sent to and received from all public and private authentication, authorization, and accounting (AAA) RADIUS servers as interpreted by the AAA Server MIB, use the show aaa servers command.

show aaa servers [ private | public ]

Syntax Description


private	(Optional) Displays private AAA servers only, which are also displayed by the AAA Server MIB.
private	(Optional) Displays public AAA servers only, which are also displayed by the AAA Server MIB.

Command Default

None

Command Modes

Privileged EXEC(#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Usage Guidelines

Only RADIUS servers are supported by the show aaa servers command.

Examples

The following command displays information about packets sent and received for all AAA transaction types--authentication, authorization, and accounting.

Device# show aaa servers 

RADIUS: id 2, priority 1, host 124.2.2.12, auth-port 1645, acct-port 1612, hostname rsim
     State: current UP, duration 20699s, previous duration 0s
     Dead: total time 0s, count 0
     Platform State from SMD: current UP, duration 20699s, previous duration 0s
     SMD Platform Dead: total time 0s, count 0
     Platform State from WNCD (1) : current UP
     Platform State from WNCD (2) : current UP
     Platform State from WNCD (3) : current UP
     Platform State from WNCD (4) : current UP
     Platform State from WNCD (5) : current UP
     Platform State from WNCD (6) : current UP
     Platform State from WNCD (7) : current UP
     Platform State from WNCD (8) : current UP, duration 964s, previous duration 0s
     Platform Dead: total time 0s, count 0UP
     Quarantined: No
.
.
.

     Elapsed time since counters last cleared: 5h44m
     Estimated Outstanding Access Transactions: 0
     Estimated Outstanding Accounting Transactions: 0
     Estimated Throttled Access Transactions: 0
     Estimated Throttled Accounting Transactions: 0
     Maximum Throttled Transactions: access 0, accounting 0
     Consecutive Response Failures: total 0
             SMD Platform : max 0, current 0 total 0
             WNCD Platform: max 0, current 0 total 0
             IOSD Platform : max 0, current 0 total 0
     Consecutive Timeouts: total 0
             SMD Platform : max 0, current 0 total 0
             WNCD Platform: max 0, current 0 total 0
             IOSD Platform : max 0, current 0 total 0
     Requests per minute past 24 hours:
             high - 5 hours, 44 minutes ago: 0
             low  - 5 hours, 44 minutes ago: 0
             average: 0

show access-list

To display access control lists (ACLs) configured on the device, use the show access-lists command in privileged EXEC mode.

show access-lists [name | number | hardware counters | ipc]

Syntax Description


`number`	(Optional) ACL number. The range is 1 to 2799.
`name`	(Optional) Name of the ACL.
hardware counters	(Optional) Displays the access list hardware counters.
ipc	(Optional) Display Interprocess Communication (IPC) protocol access-list configuration download information

Command Default

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Usage Guidelines

Though visible in the command-line help strings, the rate-limit keyword is not supported

The device supports only IP standard and extended access lists. Therefore, the allowed numbers are only 1 to 199 and 1300 to 2799.

This command also displays the MAC ACLs that are configured.

Examples

This is an example of output from the show access-lists command:

Device# show access-lists

Extended IP access list 103
    10 permit ip any any dscp af11
Extended IP access list ssm-range
    10 deny ip any 232.0.0.0 0.255.255.255
    20 permit ip any any
Extended MAC access list mac1

This is an example of output from the show access-lists hardware counters command:

Device# show access-lists hardware counters
 L3 ACL INPUT Statistics
     All  Drop:                     frame count: 0
     All  Bridge Only:              frame count: 0
     All  Forwarding To CPU:        frame count: 294674
     All  Forwarded:                frame count: 2577677
     All  Drop And Log:             frame count: 0
     All  Bridge Only And Log:      frame count: 0
     All  Forwarded And Log:        frame count: 0
     All  IPv6 Drop:                frame count: 0
     All  IPv6 Bridge Only:         frame count: 0
     All  IPv6 Forwarding To CPU:   frame count: 0
     All  IPv6 Forwarded:           frame count: 102
     All  IPv6 Drop And Log:        frame count: 0
     All  IPv6 Bridge Only And Log: frame count: 0
     All  IPv6 Forwarded And Log:   frame count: 0

 L3 ACL OUTPUT Statistics
     All  Drop:                     frame count: 0
     All  Bridge Only:              frame count: 0
     All  Forwarding To CPU:        frame count: 0
     All  Forwarded:                frame count: 266050
     All  Drop And Log:             frame count: 0
     All  Bridge Only And Log:      frame count: 0
     All  Forwarded And Log:        frame count: 0
     All  IPv6 Drop:                frame count: 0
     All  IPv6 Bridge Only:         frame count: 0
     All  IPv6 Forwarding To CPU:   frame count: 0
     All  IPv6 Forwarded:           frame count: 0
     All  IPv6 Drop And Log:        frame count: 0
     All  IPv6 Bridge Only And Log: frame count: 0
     All  IPv6 Forwarded And Log:   frame count: 0

show ap name icap subscription ap rf spectrum

To display the spectrum configuration details of a corresponding AP, use the show ap name icap subscription ap rf spectrum command.

show ap name ap_name icap subscription ap rf spectrum

Syntax Description


`ap_name`	AP name

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 17.2.1	This command was introduced.

Examples

The following example shows how to display spectrum analysis on a AP:

Device# show ap name 4800AP icap subscription ap rf spectrum 
Per-AP ICap configuration
 
AP RF spectrum subscription
  State                    : enabled
  Radio slots              : none

show ap airtime-fairness summary

To view the ATF configuration summary of all radios, use the show ap airtime-fairness summary command.

show ap airtime-fairness summary

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the ATF configuration summary of all radios:

Device# show ap airtime-fairness summary

show ap audit-report detail

To display the configuration of an AP, use the show ap ap-name audit-report detail command.

show ap ap-name audit-report detail

Syntax Description


`ap-name`	AP name.
detail	Displays audit report for an AP.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.3.1	This command was introduced.

Examples

This following example shows how to display the audit report for an AP:

Device# show ap Cisco-AP audit-report detail
Cisco AP Name   : Cisco-AP
=================================================
 
Radio Audit Report:
 
Slot   Channel   Bandwidth   Tx Power   Admin State        Operation State   Radio Role   Radio Operation
---------------------------------------------------------------------------------------------------------
0         IN_SYNC   IN_SYNC    IN_SYNC    OUT_OF_SYNC     IN_SYNC              IN_SYNC       IN_SYNC
1         IN_SYNC   IN_SYNC    IN_SYNC    OUT_OF_SYNC     IN_SYNC              IN_SYNC       IN_SYNC
 
WLAN Audit Report:
 
Slot-id Wlan-id Vlan           State                    SSID        Auth Type     Flags
------------------------------------------------------------------------------------------------
0           1            IN_SYNC    OUT_OF_SYNC IN_SYNC    IN_SYNC    IN_SYNC  
0           2            IN_SYNC    OUT_OF_SYNC IN_SYNC    IN_SYNC    IN_SYNC  
1           1            IN_SYNC    OUT_OF_SYNC IN_SYNC    IN_SYNC    IN_SYNC  
1           2            IN_SYNC    OUT_OF_SYNC IN_SYNC    IN_SYNC    IN_SYNC

show ap audit-report summary

To display the audit report summary for an AP, use the show ap audit-report summary command.

show ap audit-report summary

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.3.1	This command was introduced.

Example

The following example shows how to display the audit report summary of an AP:

Device# show ap audit-report summary
WTP Mac                    Radio                   Wlan                 IPv4 Acl          IPv6 Acl       Last Report Time
-------------------------------------------------------------------------------------------------------------------------------
1880.90fd.6b40   OUT_OF_SYNC    OUT_OF_SYNC    IN_SYNC        IN_SYNC        01/01/1970 05:30:00 IST

show ap auth-list

To see the access point authorization list, use the show ap auth-list command.

show ap auth-list [ chassis {chassis-number | active | standby} R0]

Syntax Description


`chassis-number`	Chassis number as either 1 or 2.
active R0	Active instance in Route-processor slot 0.
standby R0	Standby instance in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the access point authorization list:

Device# show ap auth-list

show ap auth-list ap-cert-policy

To verify if the APs have been authorized by the AP certificate policy, use the show ap auth-list ap-cert-policy

show ap auth-list ap-cert-policy

Syntax Description


This command has no arguments.

Command Default

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.5.1	This command was introduced.

Examples

The following example shows how to verify if the APs have been authorized by the AP certificate policy:

Device# show ap auth-list ap-cert-policy

show ap auto-rf

To display the auto-RF settings for a Cisco lightweight access point, use the show ap auto-rf command.

show ap auto-rf dot11{ 24ghz | 5ghz | dual-band} cisco_ap

Syntax Description


24ghz	Specifies the 802.11b AP.
5ghz	Specifies the 802.11a AP.
dual-band	Specifies dual bands.

Command Default

None

Usage Guidelines

The show ap auto-rf command output will not display neighbor AP names.

Examples

The following example shows how to display auto-RF information for an access point:

Device# show ap auto-rf dot11 24ghz AP1

###################################################################

Number of Slots                                   : 3
AP Name                                           : APA023.9FD8.EA22
MAC Address                                       : 40ce.24bf.8ca0
Ethernet MAC Address                              : a023.9fd8.ea22
  Slot ID                                         : 0
  Radio Type                                      : 802.11n - 2.4 GHz
  Current TX/RX Band                              : 2.4Ghz band
  Subband Type                                    : All
  Noise Information
    Noise Profile                                 : Passed
    Channel   1                                   :  -91 dBm
    Channel   2                                   :  -67 dBm
    Channel   3                                   :  -54 dBm
    Channel   4                                   :  -55 dBm
    Channel   5                                   :  -71 dBm
    Channel   6                                   :  -85 dBm
    Channel   7                                   :  -50 dBm
    Channel   8                                   :  -54 dBm
    Channel   9                                   :  -77 dBm
    Channel  10                                   :  -88 dBm
    Channel  11                                   :  -65 dBm
  Interference Information
    Interference Profile                          : Failed
    Channel   1                                   :  -47 dBm @ 21% busy
    Channel   2                                   :  -45 dBm @  2% busy
    Channel   3                                   : -128 dBm @  0% busy
    Channel   4                                   : -128 dBm @  0% busy
    Channel   5                                   :  -48 dBm @  2% busy
    Channel   6                                   :  -45 dBm @  2% busy
    Channel   7                                   :  -42 dBm @  3% busy
    Channel   8                                   : -128 dBm @  0% busy
    Channel   9                                   : -128 dBm @  0% busy
    Channel  10                                   :  -39 dBm @  3% busy
    Channel  11                                   :  -46 dBm @  3% busy
    Rogue Histogram (20)
      Channel   1                                 : 36
      Channel   2                                 :  0
      Channel   3                                 :  0
      Channel   4                                 :  1
      Channel   5                                 :  0
      Channel   6                                 : 11
      Channel   7                                 :  0
      Channel   8                                 :  1
      Channel   9                                 :  3
      Channel  10                                 :  0
      Channel  11                                 : 14
  Load Information
    Load Profile                                : Failed
    Receive Utilization                         : 0%
    Transmit Utilization                        : 0%
    Channel Utilization                         : 98%
    Attached Clients                            : 0 clients
  Coverage Information
    Coverage Profile                            : Passed
    Failed Clients                              : 0 clients
  Client Signal Strengths
    RSSI -100 dBm                               : 0 clients
    RSSI  -92 dBm                               : 0 clients
    RSSI  -84 dBm                               : 0 clients
    RSSI  -76 dBm                               : 0 clients
    RSSI  -68 dBm                               : 0 clients
    RSSI  -60 dBm                               : 0 clients
    RSSI  -52 dBm                               : 0 clients
  Client Signal to Noise Ratios
    SNR    0 dB                                 : 0 clients
    SNR    5 dB                                 : 0 clients
    SNR   10 dB                                 : 0 clients
    SNR   15 dB                                 : 0 clients
    SNR   20 dB                                 : 0 clients
    SNR   25 dB                                 : 0 clients
    SNR   30 dB                                 : 0 clients
    SNR   35 dB                                 : 0 clients
    SNR   40 dB                                 : 0 clients
    SNR   45 dB                                 : 0 clients
  Nearby APs
    AP d0ec.3572.b9a0 slot 0                    :  -23 dBm on ( 11, 20 MHz) (181.22.0.22)
    AP 0c75.bdb3.9000 slot 0                    :  -28 dBm on ( 11, 20 MHz) (181.21.0.21)
    AP a4b2.3980.3740 slot 0                    :  -28 dBm on (  1, 20 MHz) (181.21.0.21)
    AP d0ec.3576.8320 slot 0                    :  -33 dBm on ( 11, 20 MHz) (50.1.1.122)
    AP a0f8.49dc.9780 slot 0                    :  -34 dBm on (  1, 20 MHz) (9.9.57.94)
    AP a0f8.49dc.8260 slot 0                    :  -34 dBm on (  6, 20 MHz) (9.9.57.94)
    AP d0ec.3573.7c80 slot 0                    :  -36 dBm on (  6, 20 MHz) (192.185.183.44)
    AP 00b0.e192.9d20 slot 0                    :  -36 dBm on ( 11, 20 MHz) (9.9.42.47)
    AP a4b2.397f.41c0 slot 0                    :  -36 dBm on (  1, 20 MHz) (185.10.0.10)
    AP 2c5a.0fd5.b8c0 slot 0                    :  -36 dBm on (  6, 20 MHz) (9.7.97.51)
    AP a488.7351.4740 slot 0                    :  -36 dBm on ( 11, 20 MHz) (9.7.97.51)
    AP 10b3.d5e9.c8e0 slot 0                    :  -36 dBm on (  1, 20 MHz) (50.1.1.122)
    AP 0c75.bdb3.ab00 slot 0                    :  -37 dBm on (  6, 20 MHz) (185.10.0.10)
    AP 68ca.e451.5120 slot 0                    :  -37 dBm on (  1, 20 MHz) (9.4.155.15)
    AP a0f8.49dc.97a0 slot 0                    :  -37 dBm on ( 11, 20 MHz) (9.9.57.94)
    AP 188b.4501.7940 slot 0                    :  -38 dBm on ( 11, 20 MHz) (9.9.57.94)
    AP 002c.c88a.f8e0 slot 0                    :  -38 dBm on ( 11, 20 MHz) (9.9.50.55)
    AP 7069.5a78.4960 slot 0                    :  -38 dBm on ( 11, 20 MHz) (9.7.97.51)
    AP 3c41.0ea7.0880 slot 0                    :  -39 dBm on ( 11, 20 MHz) (185.10.0.10)
    AP a0f8.49dc.93a0 slot 0                    :  -39 dBm on (  6, 20 MHz) (9.9.57.94)
    AP f4db.e685.7360 slot 0                    :  -39 dBm on (  6, 20 MHz) (50.1.1.122)
    AP 7070.8bb4.4120 slot 0                    :  -40 dBm on ( 11, 20 MHz) (9.9.57.94)
    AP 707d.b93e.39e0 slot 0                    :  -40 dBm on (  1, 20 MHz) (4.4.4.1)
    AP 706d.150c.6860 slot 0                    :  -40 dBm on ( 11, 20 MHz) (50.1.1.122)
  Radar Information
  Channel Assignment Information via DCA
    Current Channel Average Energy                :  -50 dBm
    Previous Channel Average Energy               :  -50 dBm
    Channel Change Count                          : 9
    Last Channel Change Time                      : 02/14/2021 20:54:57
    Recommended Best Channel                      : 1
  RF Parameter Recommendations
    Power Level                                   : 8
    RTS/CTS Threshold                             : 2347
    Fragmentation Threshold                       : 2346
    Antenna Pattern                               : 0
  Persistent Interference Devices
  Class Type                 Channel  DC (%%)  RSSI (dBm)  Last Update Time
  -------------------------  -------  ------   ---------   ----------------
  All third party trademarks are the property of their respective owners.

show ap ble cmx detail ip

To view the BLE management feature related global values for a specific CMX along with all the APs associated to that CMX, use the show ap ble cmx detail ip command.

show ap ble cmx detail ip CMX-IP

Syntax Description


`CMX-IP`	Specifies the IPv4 address.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Usage Guidelines

Examples

This example shows how to display the BLE management feature related global values for a specific CMX along with all the APs associated to that CMX:

Device# show ap ble cmx detail ip 10.1.2.3
BLE administrative status: Up
BLE operational status: Up
Scanning interval: 10

  AP Name                         Interface             Status
  ----------------------------------------------------------------
  AP4001.7AB2.C39A                Integrated            Open

show ap ble cmx summary

To view the list of all CMXs registered for BLE Management feature and their global values for BLE, use the show ap ble cmx summary command.

show ap ble cmx summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Usage Guidelines

Examples

This example shows how to view the list of all CMXs registered for BLE Management feature and their global values for BLE:

Device# show ap ble cmx summary
CMX IP: 10.1.2.3
-----------------------
  BLE administrative status: Up
  BLE operational status: Up
  Scanning interval: 12

CMX IP: 10.1.2.4
-----------------------
  BLE administrative status: Down
  BLE operational status: Down
   Reason: BLE is administratively down 
  Scanning interval: 0

CMX IP: 10.1.2.5
------------------
BLE administrative status: Up
BLE operational status: Down
 Reason: CMX is not subscribed to AP Monitor and RSSI services, or NMSP connection is down
Scanning interval: 10

show ap ble summary

To view the list of joined APs that support BLE Management feature along with the BLE details for each AP, use the show ap ble summary command.

show ap ble summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.
Cisco IOS XE Cupertino 17.9.1	The output of the command is modified to add new column that displays scan status.

Usage Guidelines

The BLE Management feature is enabled and APs are displayed only when the CMX is registered with the controller, and BLE is enabled on CMX.

Examples

This example shows how to view the list of joined APs that support BLE Management feature along with the BLE details for each AP:

Device# show ap ble summary
AP Name                         Interface             Status      CMX IP
----------------------------------------------------------------------------------
AP4001.7AB2.C39A                Integrated            Open        10.1.2.3
AP4001.7AB2.C39B                Integrated            Closed      10.1.2.4

Device# show ap ble summary 

AP Name   AP Model     AP Ethernet MAC  BLE               BLE           BLE mode       BLE MAC         BLE Profile       BLE Scan
                                        Interface State   Admin State
------------------------------------------------------------------------------------------------------------------------------------------
AP794     C9130AXI-B   04eb.409e.xxxx   Open              Up            Base (Native)  806f.b031.xxxx  Eddystone URL     Enabled/Disabled
AP50      C9130AXI-B   04eb.409e.xxxx   Close             Down          Base (Native)  Unknown         Not Configured    Enabled/Disabled
AP28      C9136I       687d.b45c.xxxx   Close             Down          Base (Native)  Unknown         Not Configured    Enabled/Disabled

show ap config

To display configuration settings for all access points that join the device, use the show ap config command.

show ap config {general | global}

Syntax Description


ethernet	Displays ethernet VLAN tagging information for all Cisco APs.
general	Displays common information for all Cisco APs.
global	Displays global settings for all Cisco APs.

Command Default

None

Command Modes

Any command mode

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to display global syslog server settings:

Device# show ap config global

AP global system logging host                    : 255.255.255.255

show ap config general

To view the general configuration information of all the Cisco APs, use the show ap config general command.

show ap config general

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to view the general configuration information of all Cisco APs:

Device# show ap config general
Cisco AP Name   : AP4C77.6DF2.D588
=================================================
<SNIP>
Dhcp Server                                     : Enabled

show ap client-trace events all

To view the AP client trace event information, use the show ap client-trace events all command.

show ap client-trace events all

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.2.1	This command was introduced.

Examples

This example shows how to view the AP client trace event information:

Device# show ap client-trace events all

[*04/29/2019 11:49:21.964964] [AP58AC.78DC.AAA0] [38:e6:0a:ea:99:d4] <apr1v0> [D:W] DOT11_AUTHENTICATION : (.)
[*04/29/2019 11:49:21.972209] [AP58AC.78DC.AAA0] [38:e6:0a:ea:99:d4] <apr1v0> [U:W] DOT11_ASSOC_REQUEST : (.)
[*04/29/2019 11:49:21.972227] [58:ac:78:df:6d:0f] [client] Vendor specific OUI: 00:50:f2 and Type: 02
[*04/29/2019 11:49:21.975975] [AP58AC.78DC.AAA0] [38:e6:0a:ea:99:d4] <apr1v0> [D:W] DOT11_ASSOC_RESPONSE : (.)

show ap crash-file

To display the list of both crash and radio core dump files generated by lightweight access points, use the show ap crash-file command.

show ap crash-filechassis chassis-number <1-2>active standby

Syntax Description


chassis	Displays the chassis details.
`chassis-number`	Specifies the chassis number, either 1 or 2.
active	Specifies an active instance.
standby	Specifies a standby instance.

Command Default

None

Command Modes

Any command mode

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to display the crash file generated by the access point:

Device# show ap crash-file

show ap dot11

To view 802.11a or 802.11b or 6-GHz configuration information, use the show ap dot11 command.

show ap dot11 { 24ghz | 5ghz | 6ghz } { channel | coverage | group | load-info | logging | media-stream | monitor | network | profile | receiver | service-policy | summary | txpower | ccx global }

Syntax Description


24ghz	Specifies the 2.4-GHz band.
5ghz	Specifies the 5-GHz band.
6ghz	Specifies the 6-GHz band.
channel	Displays the automatic channel assignment configuration and statistics.
coverage	Displays the configuration and statistics for coverage hole detection.
group	Displays 802.11a, 6-GHz or 802.11b Cisco radio RF grouping.
load-info	Displays channel utilization and client count information for all Cisco APs.
logging	Displays 802.11a, 6-GHz or 802.11b RF event and performance logging.
media-stream	Display 802.11a, 6-GHz or 802.11b Media Resource Reservation Control configurations.
monitor	Displays the 802.11a, 6-GHz or 802.11b default Cisco radio monitoring.
network	Displays the 802.11a, 6-GHz or 802.11b network configuration.
profile	Displays the 802.11a, 6-GHz or 802.11b lightweight access point performance profiles.
receiver	Displays the configuration and statistics of the 802.11a, 6-GHz or 802.11b receiver.
service-policy	Displays the Quality of Service (QoS) service policies for 802.11a, 6-GHz or 802.11b radio for all Cisco access points.
summary	Displays the 802.11a, 6-GHz or 802.11b Cisco lightweight access point name, channel, and transmit level summary.
txpower	Displays the 802.11a, 6-GHz or 802.11b automatic transmit power assignment.
ccx global	Displays 802.11a, 6-GHz or 802.11b Cisco Client eXtensions (CCX) information for all Cisco access points that are joined to the device.

Command Default

None

Command Modes

Any command mode

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1 Cisco IOS XE Gibraltar 16.12.2s	This command was introduced.
	The load-info parameter was added.
Cisco IOS XE Cupertino 17.7.1	This command was modified to include the 6-GHz band.

Examples

This example shows how to display the automatic channel assignment configuration and statistics:

Device# show ap dot11 5ghz channel
Automatic Channel Assignment
  Channel Assignment Mode                    : AUTO
  Channel Update Interval                    : 12 Hours
  Anchor time (Hour of the day)              : 20
  Channel Update Contribution                : SNI.
  Channel Assignment Leader                  : web (9.9.9.2)
  Last Run                                   : 13105 seconds ago
  DCA Sensitivity Level                      : MEDIUM (15 dB)
  DCA 802.11n Channel Width                  : 40 Mhz
  Channel Energy Levels
      Minimum                                : unknown
      Average                                : unknown
      Maximum                                : unknown
  Channel Dwell Times
      Minimum                                : unknown
      Average                                : unknown
      Maximum                                : unknown
  802.11a 5 GHz Auto-RF Channel List
  Allowed Channel List                       : 36,40,44,48,52,56,60,64,149,153,1
57,161
  Unused Channel List                        : 100,104,108,112,116,132,136,140,1
65
  802.11a 4.9 GHz Auto-RF Channel List
  Allowed Channel List                       :
  Unused Channel List                        : 1,2,3,4,5,6,7,8,9,10,11,12,13,14,
15,16,17,18,19,20,21,22,23,24,25,26
  DCA Outdoor AP option                      : Disabled

This example shows how to display the statistics for coverage hole detection:

Device# show ap dot11 5ghz coverage
Coverage Hole Detection
  802.11a Coverage Hole Detection Mode          : Enabled
  802.11a Coverage Voice Packet Count           : 100 packet(s)
  802.11a Coverage Voice Packet Percentage      : 50 %
  802.11a Coverage Voice RSSI Threshold         : -80dBm
  802.11a Coverage Data Packet Count            : 50 packet(s)
  802.11a Coverage Data Packet Percentage       : 50 %
  802.11a Coverage Data RSSI Threshold          : -80dBm
  802.11a Global coverage exception level       : 25
  802.11a Global client minimum exception level   : 3 clients

This example shows how to display Cisco radio RF group settings:

Device# show ap dot11 5ghz group
Radio RF Grouping

  802.11a Group Mode                 : STATIC
  802.11a Group Update Interval      : 600 seconds
  802.11a Group Leader               : web (10.10.10.1)
  802.11a Group Member               : web(10.10.10.1)
                                       nb1(172.13.21.45) (*Unreachable)
  802.11a Last Run                   : 438 seconds ago


  Mobility Agents RF membership information
  ------------------------------------------------------------
  No of 802.11a MA RF-members : 0

This example shows how to display 802.11a RF event and performance logging:

Device# show ap dot11 5ghz logging
RF Event and Performance Logging

  Channel Update Logging              : Off
  Coverage Profile Logging            : Off
  Foreign Profile Logging             : Off
  Load Profile Logging                : Off
  Noise Profile Logging               : Off
  Performance Profile Logging         : Off
  TxPower Update Logging              : Off

This example shows how to display the 802.11a media stream configuration:

Device# show ap dot11 5ghz media-stream
Multicast-direct                 : Disabled
Best Effort                      : Disabled
Video Re-Direct                  : Disabled
Max Allowed Streams Per Radio      : Auto
Max Allowed Streams Per Client     : Auto
Max Video Bandwidth               : 0
Max Voice Bandwidth               : 75
Max Media Bandwidth               : 85
Min PHY Rate (Kbps)               : 6000
Max Retry Percentage              : 80

This example shows how to display the radio monitoring for the 802.11b network:

Device# show ap dot11 5ghz monitor
Default 802.11a AP monitoring

  802.11a Monitor Mode                           : Enabled
  802.11a Monitor Mode for Mesh AP Backhaul      : disabled
  802.11a Monitor Channels                       : Country channels
  802.11a RRM Neighbor Discover Type             : Transparent
  802.11a AP Coverage Interval                   : 180 seconds
  802.11a AP Load Interval                       : 60 seconds
  802.11a AP Noise Interval                      : 180 seconds
  802.11a AP Signal Strength Interval            : 60 seconds

This example shows how to display the global configuration and statistics of an 802.11a profile:

Device# show ap dot11 5ghz profile
Default 802.11a AP performance profiles
802.11a Global Interference threshold.............. 10%
802.11a Global noise threshold..................... -70 dBm
802.11a Global RF utilization threshold............ 80%
802.11a Global throughput threshold................ 1000000 bps
802.11a Global clients threshold................... 12 clients
802.11a Global coverage threshold.................. 12 dB
802.11a Global coverage exception level............ 80%
802.11a Global client minimum exception lev........ 3 clients

This example shows how to display the network configuration of an 802.11a profile:

Device# show ap dot11 5ghz network
802.11a Network : Enabled
11nSupport : Enabled
  802.11a Low Band : Enabled
  802.11a Mid Band : Enabled
  802.11a High Band : Enabled

802.11a Operational Rates
  802.11a 6M : Mandatory
  802.11a 9M : Supported
  802.11a 12M : Mandatory
  802.11a 18M : Supported
  802.11a 24M : Mandatory
  802.11a 36M : Supported
  802.11a 48M : Supported
  802.11a 54M : Supported
802.11n MCS Settings:
  MCS 0 : Supported
  MCS 1 : Supported
  MCS 2 : Supported
  MCS 3 : Supported
  MCS 4 : Supported
  MCS 5 : Supported
  MCS 6 : Supported
  MCS 7 : Supported
  MCS 8 : Supported
  MCS 9 : Supported
  MCS 10 : Supported
  MCS 11 : Supported
  MCS 12 : Supported
  MCS 13 : Supported
  MCS 14 : Supported
  MCS 15 : Supported
  MCS 16 : Supported
  MCS 17 : Supported
  MCS 18 : Supported
  MCS 19 : Supported
  MCS 20 : Supported
  MCS 21 : Supported
  MCS 22 : Supported
  MCS 23 : Supported
802.11n Status:
  A-MPDU Tx:
    Priority 0 : Enabled
    Priority 1 : Disabled
    Priority 2 : Disabled
    Priority 3 : Disabled
    Priority 4 : Enabled
    Priority 5 : Enabled
    Priority 6 : Disabled
    Priority 7 : Disabled
  A-MSDU Tx:
    Priority 0 : Enabled
    Priority 1 : Enabled
    Priority 2 : Enabled
    Priority 3 : Enabled
    Priority 4 : Enabled
    Priority 5 : Enabled
    Priority 6 : Disabled
    Priority 7 : Disabled
  Guard Interval : Any
  Rifs Rx : Enabled
Beacon Interval : 100
CF Pollable mandatory : Disabled
CF Poll Request Mandatory : Disabled
CFP Period : 4
CFP Maximum Duration : 60
Default Channel : 36
Default Tx Power Level : 1
DTPC Status : Enabled
Fragmentation Threshold : 2346
Pico-Cell Status : Disabled
Pico-Cell-V2 Status : Disabled
TI Threshold : 0
Legacy Tx Beamforming setting : Disabled
Traffic Stream Metrics Status : Disabled
Expedited BW Request Status : Disabled
EDCA profile type check : default-wmm
Call Admision Control (CAC) configuration
Voice AC
  Voice AC - Admission control (ACM) : Disabled
  Voice Stream-Size : 84000
  Voice Max-Streams : 2
  Voice Max RF Bandwidth : 75
  Voice Reserved Roaming Bandwidth : 6
  Voice Load-Based CAC mode : Enabled
  Voice tspec inactivity timeout : Enabled
CAC SIP-Voice configuration
  SIP based CAC : Disabled
  SIP call bandwidth : 64
  SIP call bandwith sample-size : 20
Video AC
  Video AC - Admission control (ACM) : Disabled
  Video max RF bandwidth : Infinite
  Video reserved roaming bandwidth : 0

This example shows how to display the global configuration and statistics of an 802.11a profile:

Device# show ap dot11 5ghz receiver
Default 802.11a AP performance profiles
802.11a Global Interference threshold.............. 10%
802.11a Global noise threshold..................... -70 dBm
802.11a Global RF utilization threshold............ 80%
802.11a Global throughput threshold................ 1000000 bps
802.11a Global clients threshold................... 12 clients
802.11a Global coverage threshold.................. 12 dB
802.11a Global coverage exception level............ 80%
802.11a Global client minimum exception lev........ 3 clients

This example shows how to display the global configuration and statistics of an 802.11a profile:

Device# show ap dot11 5ghz service-policy

This example shows how to display a summary of the 802.11b access point settings:

Device# show ap dot11 5ghz summary
AP Name MAC Address       Admin State Operation State Channel TxPower
------- ----------------- ----------- --------------- ------- -------
CJ-1240 00:21:1b:ea:36:60 ENABLED     UP              161     1( )
CJ-1130 00:1f:ca:cf:b6:60 ENABLED     UP              56*     1(*)

This example shows how to display the configuration and statistics of the 802.11a transmit power cost:

Device# show ap dot11 5ghz txpower
Automatic Transmit Power Assignment

Transmit Power Assignment Mode          : AUTO
Transmit Power Update Interval          : 600 seconds
Transmit Power Threshold                : -70 dBm
Transmit Power Neighbor Count           : 3 APs
Min Transmit Power                      : -10 dBm
Max Transmit Power                      : 30 dBm
Transmit Power Update Contribution      : SNI.
Transmit Power Assignment Leader        : web (10.10.10.1)
Last Run                                : 437 seconds ago

This example shows how to display the configuration and statistics of the 802.11a transmit power cost:

Device# show ap dot11 5ghz ccx global
 802.11a Client Beacon Measurements:
     disabled

show ap dot11

To display 802.11 band parameters, use the show ap dot11 command.

show ap dot11 {24ghz | 5ghz} {media-stream rrc | network | profile | summary}

Syntax Description


media-stream rrc	Displays Media Stream configurations.
network	Shows network configuration.
profile	Shows profiling information for all Cisco APs.
summary	Shows configuration and statistics of 802.11b and 802.11a Cisco APs.

Command Default

None

Command Modes

User EXEC command mode or Privileged EXEC command mode

Usage Guidelines

None.

Examples

The following is a sample output of the show ap dot11 24ghz media-stream rrc command.


Device#show ap dot11 24ghz media-stream rrc

Multicast-direct                 : Disabled
Best Effort                      : Disabled
Video Re-Direct                  : Disabled
Max Allowed Streams Per Radio      : Auto
Max Allowed Streams Per Client     : Auto
Max Video Bandwidth               : 0
Max Voice Bandwidth               : 75
Max Media Bandwidth               : 85
Min PHY Rate (Kbps)               : 6000
Max Retry Percentage              : 80

show ap dot11 24ghz

To display the 2.4 GHz RRM parameters, use the show ap dot11 24ghz command.

show ap dot11 24ghz {ccx | channel | coverage | group | l2roam | logging | monitor | profile | receiver | summary | txpower}

Syntax Description


ccx	Displays the 802.11b CCX information for all Cisco APs.
channel	Displays the configuration and statistics of the 802.11b channel assignment.
coverage	Displays the configuration and statistics of the 802.11b coverage.
group	Displays the configuration and statistics of the 802.11b grouping.
l2roam	Displays 802.11b l2roam information.
logging	Displays the configuration and statistics of the 802.11b event logging.
monitor	Displays the configuration and statistics of the 802.11b monitoring.
profile	Displays 802.11b profiling information for all Cisco APs.
receiver	Displays the configuration and statistics of the 802.11b receiver.
summary	Displays the configuration and statistics of the 802.11b Cisco APs.
txpower	Displays the configuration and statistics of the 802.11b transmit power control.

Command Default

None.

Command Modes

Global configuration.

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to display configuration and statistics of the 802.11b coverage.

Device#show ap dot11 24ghz coverage

Coverage Hole Detection
  802.11b Coverage Hole Detection Mode             : Enabled
  802.11b Coverage Voice Packet Count              : 100 packet(s)
  802.11b Coverage Voice Packet Percentage         : 50%
  802.11b Coverage Voice RSSI Threshold            : -80 dBm
  802.11b Coverage Data Packet Count               : 50 packet(s)
  802.11b Coverage Data Packet Percentage          : 50%
  802.11b Coverage Data RSSI Threshold             : -80 dBm
  802.11b Global coverage exception level          : 25 %
  802.11b Global client minimum exception level    : 3 clients

show ap dot11 24ghz SI config

To see the spectrum intelligence (SI) configuration details for the 2.4-GHz band, use the show ap dot11 24ghz SI config command.

show ap dot11 24ghz SI config [ chassis {chassis-number | active | standby} R0]

Syntax Description


`chassis-number`	Chassis number as either 1 or 2.
active R0	Active instance of the configuration in Route-processor slot 0.
standby R0	Standby instance of the configuration in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the SI configuration details for the 2.4-GHz band:

Device# show ap dot11 24ghz SI config chassis 1 R0

show ap dot11 24ghz SI device type

To see the spectrum intelligence (SI) interferers of different types for the 2.4-GHz band, use the show ap dot11 24ghz SI device type command.

show ap dot11 24ghz SI device type {cont_tx | mw_oven | si_fhss} [ chassis {chassis-number | active | standby} R0]

Syntax Description


cont_tx	SI interferers of type Continuous transmitter for the 2.4-GHz band.
mw_oven	SI interferers of type microwave oven for the 2.4-GHz band.
si_fhss	SI interferers of type Frequency Hopping Spread Spectrum for the 2.4-GHz band.
`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the configuration in Route-processor slot 0.
standby R0	Standby instance of the configuration in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the details of SI interferers of type microwave oven in the 2.4-GHz band:

Device# show ap dot11 24ghz SI device type mw_oven chassis 1 R0

show ap dot11 5ghz

To display the 5GHz RRM parameters, use the show ap dot11 5ghz command.

show ap dot11 5ghz {ccx | channel | coverage | group | l2roam | logging | monitor | profile | receiver | summary | txpower}

Syntax Description


ccx	Displays the 802.11a CCX information for all Cisco APs.
channel	Displays the configuration and statistics of the 802.11a channel assignment.
coverage	Displays the configuration and statistics of the 802.11a coverage.
group	Displays the configuration and statistics of the 802.11a grouping.
l2roam	Displays 802.11a l2roam information.
logging	Displays the configuration and statistics of the 802.11a event logging.
monitor	Displays the configuration and statistics of the 802.11a monitoring.
profile	Displays 802.11a profiling information for all Cisco APs.
receiver	Displays the configuration and statistics of the 802.11a receiver.
summary	Displays the configuration and statistics of the 802.11a Cisco APs.
txpower	Displays the configuration and statistics of the 802.11a transmit power control.

Command Default

None.

Command Modes

Global configuration.

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

None.

Examples

This example shows configuration and statistics of 802.11a channel assignment.

Device#show ap dot11 5ghz channel

Automatic Channel Assignment
  Channel Assignment Mode                    : AUTO
  Channel Update Interval                    : 12 Hours
  Anchor time (Hour of the day)              : 20
  Channel Update Contribution                : SNI..
  Channel Assignment Leader                  : web (9.9.9.2)
  Last Run                                   : 16534 seconds ago
  DCA Sensitivity Level                      : MEDIUM (15 dB)
  DCA 802.11n Channel Width                  : 40 Mhz
  Channel Energy Levels
      Minimum                                : unknown
      Average                                : unknown
      Maximum                                : unknown
  Channel Dwell Times
      Minimum                                : unknown
      Average                                : unknown
      Maximum                                : unknown
  802.11a 5 GHz Auto-RF Channel List
  Allowed Channel List                       : 36,40,44,48,52,56,60,64,149,153,1                                                                                                                     57,161
  Unused Channel List                        : 100,104,108,112,116,132,136,140,1                                                                                                                     65
  802.11a 4.9 GHz Auto-RF Channel List
  Allowed Channel List                       :
  Unused Channel List                        : 1,2,3,4,5,6,7,8,9,10,11,12,13,14,                                                                                                                     15,16,17,18,19,20,21,22,23,24,25,26
  DCA Outdoor AP option                      : Disabled

show ap dot11 24ghz cleanair air-quality

To display the air-quality summary information and air-quality worst information for the 802.11 networks, use the show ap dot11 cleanair command.

show ap dot11 {24ghz | 5ghz | dual-band} cleanair {air-quality | config | device | summary}

Syntax Description


24ghz	Displays the 2.4 GHz band.
5ghz	Displays the 5 GHz band.
dual-band	Displays 802.11 dual-band radios.
cleanair	Displays cleanair configurations.
air-quality	Displays the Cleanair Air-Quality (AQ) data for 2.4GHz band.
device	Displays the CleanAir Interferers of device for 2.4GHz band.
config	Displays CleanAir Configuration for 2.4GHz band.
summary	Displays cleanair configurations for all 802.11a Cisco APs.

Command Default

None

Command Modes

Any command mode

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to display the worst air-quality information for the 5 GHz band:

Device# show ap dot11 5ghz cleanair air-quality worst

AQ = Air Quality
DFS = Dynamic Frequency Selection
AP Name      Channel Avg AQ Min AQ Interferers DFS
------------ ------- ------ ------ ----------- -----
CISCO_AP3500 36      95     70     0           40

This example shows how to display the worst air-quality information for the 2.4 GHz band:

Device# show ap dot11 24ghz cleanair air-quality worst

AQ = Air Quality
DFS = Dynamic Frequency Selection
AP Name      Channel Avg AQ Min AQ Interferers DFS
------------ ------- ------ ------ ----------- -----
CISCO_AP3500 1       83     57     3           5

show ap dot11 24ghz cleanair air-quality

To display the air-quality summary information and air-quality worst information for the 802.11 networks, use the show ap dot11 cleanair air-quality command.

show ap dot11 {24ghz | 5ghz} cleanair air-quality {summary | worst}

Syntax Description


24ghz	Displays the 2.4 GHz band.
5ghz	Displays the 5 GHz band.
summary	Displays a summary of 802.11 radio band air-quality information.
worst	Displays the worst air-quality information for 802.11 networks.

Command Default

None

Command Modes

Any command mode

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to display the worst air-quality information for the 5 GHz band:

Device# show ap dot11 5ghz cleanair air-quality worst

AQ = Air Quality
DFS = Dynamic Frequency Selection
AP Name      Channel Avg AQ Min AQ Interferers DFS
------------ ------- ------ ------ ----------- -----
CISCO_AP3500 36      95     70     0           40

This example shows how to display the worst air-quality information for the 2.4 GHz band:

Device# show ap dot11 24ghz cleanair air-quality worst

AQ = Air Quality
DFS = Dynamic Frequency Selection
AP Name      Channel Avg AQ Min AQ Interferers DFS
------------ ------- ------ ------ ----------- -----
CISCO_AP3500 1       83     57     3           5

show ap dot11 cleanair config

To display the CleanAir configuration for the 802.11 networks, use the show ap dot11 cleanair config command.

show ap dot11 {24ghz | 5ghz} cleanair config

Syntax Description


24ghz	Displays the 2.4 GHz band.
5ghz	Displays the 5 GHz band.

Command Default

None

Command Modes

Any command mode

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to display the CleanAir configuration for the 2.4 GHz band:

Device# show ap dot11 24ghz cleanair config
Clean Air Solution............................... : Disabled
Air Quality Settings:
    Air Quality Reporting........................ : Disabled
    Air Quality Reporting Period (min)........... : 15
    Air Quality Alarms........................... : Enabled
    Air Quality Alarm Threshold.................. : 10
Interference Device Settings:
    Interference Device Reporting................ : Enabled
        Bluetooth Link........................... : Enabled
        Microwave Oven........................... : Enabled
        802.11 FH................................ : Enabled
        Bluetooth Discovery...................... : Enabled
        TDD Transmitter.......................... : Enabled
        Jammer................................... : Enabled
        Continuous Transmitter................... : Enabled
        DECT-like Phone.......................... : Enabled
        Video Camera............................. : Enabled
        802.15.4................................. : Enabled
        WiFi Inverted............................ : Enabled
        WiFi Invalid Channel..................... : Enabled
        SuperAG.................................. : Enabled
        Canopy................................... : Enabled
        Microsoft Device......................... : Enabled
        WiMax Mobile............................. : Enabled
        WiMax Fixed.............................. : Enabled
    Interference Device Types Triggering Alarms:
        Bluetooth Link........................... : Disabled
        Microwave Oven........................... : Disabled
        802.11 FH................................ : Disabled
        Bluetooth Discovery...................... : Disabled
        TDD Transmitter.......................... : Disabled
        Jammer................................... : Disabled
        Continuous Transmitter................... : Disabled
        DECT-like Phone.......................... : Disabled
        Video Camera............................. : Disabled
        802.15.4................................. : Disabled
        WiFi Inverted............................ : Enabled
        WiFi Invalid Channel..................... : Enabled
        SuperAG.................................. : Disabled
        Canopy................................... : Disabled
        Microsoft Device......................... : Disabled
        WiMax Mobile............................. : Disabled
        WiMax Fixed.............................. : Disabled
    Interference Device Alarms................... : Enabled
Additional Clean Air Settings:
    CleanAir Event-driven RRM State.............. : Disabled
    CleanAir Driven RRM Sensitivity.............. : LOW
    CleanAir Persistent Devices state............ : Disabled

show ap dot11 cleanair summary

To view CleanAir configurations for all 802.11a Cisco APs, use the show ap dot11 cleanair summary command.

show ap dot11 {24ghz | 5ghz} cleanair summary

Syntax Description


24ghz	Specifies the 2.4-GHz band
5ghz	Specifies the 5-GHz band
cleanair summary	Summary of CleanAir configurations for all 802.11a Cisco APs

Command Default

None

Command Modes

Any command mode

Command History


Release	Modification
	This command was introduced.

show ap dot11 dual-band summary

To view a brief summary of access points with dual-band radios, use the show ap dot11 dual-band summary command.

show ap dot11 dual-band summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.12.1	This command was introduced.

Examples

The following example shows how to view brief summary of tag names:

Device# show ap dot11 dual-band summary

show ap environment

To see the AP environment information of all APs, use the show ap environment command.

show ap environment [ chassis {chassis-number | active | standby} R0]

Syntax Description


`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the AP filters in Route-processor slot 0.
standby R0	Standby instance of the AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the AP environment information:

Device# show ap environment

show ap filters active

To see the details of active AP filters, use the show ap filters active command.

show ap filters active [ chassis {chassis-number | active | standby} R0]

Syntax Description


`chassis-number`	Chassis number as either 1 or 2.
active R0	Active instance of the active AP filters in Route-processor slot 0.
standby R0	Standby instance of the active AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the details of the active AP filters for the active instance:

Device# show ap filters active chassis active R0

show ap filters active type priming

To display the list of all the active priming filters, use the show ap filters active type priming command.

show ap filters active type priming

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.9.2	This command was introduced.

Examples

The following example shows how to display the list of all the active priming filters:

Device# show ap filters active type priming

Priority   Filter Name                       regex                            Priming profile                                        
--------------------------------------------------------------------------------------------------------
 0          FLR2                             *AP-FLOOR-2*                     AP-PRIMING-2                                                                                                   
 1          FLR1                             *AP-FLOOR-1*                     AP-PRIMING-1

show ap filters all

To see the details of all AP filters, use the show ap filters all command.

show ap filters all [ chassis {chassis-number | active | standby} R0]

Syntax Description


`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the AP filters in Route-processor slot 0.
standby R0	Standby instance of the AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the details of all the AP filters for the active instance:

Device# show ap filters all chassis active R0

show ap filters all type priming

To display the list of all the priming filters, use the show ap filters all type priming command.

show ap filters all type priming

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.9.2	This command was introduced.

Examples

The following example shows how to display the list of all the priming filters:

Device# show ap filters all type priming

Filter Name                       regex                               Priming profile    
--------------------------------------------------------------------------------------------
FLR1                               *AP-FLOOR-1*                       AP-PRIMING-1           
FLR2                               *AP-FLOOR-2*                       AP-PRIMING-2

show ap fra

To see the flexible radio assignment (FRA) configurations in APs, use the show ap fra command.

show ap fra [ chassis {chassis-number | active | standby} R0]

Syntax Description


`chassis-number`	Chassis number as either 1 or 2.
active R0	Active instance in Route-processor slot 0.
standby R0	Standby instance in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the FRA configurations in APs:

Device# show ap fra

show ap fra 5-6ghz

To view the Flexible Radio Assignment (FRA) 5/6-GHz configurations, use the show ap fra 5-6ghz command.

show ap fra 5-6ghz

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC #

Command History


Release	Modification
Cisco IOS XE Cupertino 17.9.1	This command was introduced.

Examples

This example shows how to view the Flexible Radio Assignment (FRA) 5/6-GHz configurations:

Device# show ap fra 5-6ghz

show ap gps location

To see the GPS location of all APs, use the show ap gps location command.

show ap gps location [ chassis {chassis-number | active | standby} R0]

Syntax Description


`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the AP filters in Route-processor slot 0.
standby R0	Standby instance of the AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the GPS location of all APs:

Device# show ap gps location

show ap grpc summary

To display the status summary of GRPC channel from the AP to Cisco DNA, use the show ap grpc summary command.

show ap grpc summary

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.3.1	This command was introduced.

Usage Guidelines

None

Examples

The following example shows how to display the status summary of GRPC channel from the AP to Cisco DNA:

Device(config)# show ap grpc summary

show ap group hyperlocation

To view a summary or detailed information of Hyperlocation configuration for an AP group, use the show ap group ap-group-name hyperlocation command.

show ap group hyperlocation { summary|detail}

Syntax Description


summary	Shows the overall configuration values (AP group specific) and operational status and parameters for the AP group.
detail	Shows both overall (AP group specific) and per-AP configuration values and operational status for the AP group. The APs listed are only those that belong to the AP group.

Command Modes

User EXEC

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Denali 16.3.1	This command was introduced.

Examples

This example shows how to view a summary of Hyperlocation configuration for an AP group:

Device# show ap group my-ap-group hyperlocation summary

Site Name: my-ap-group
Site Description: This is an AP group
Hyperlocation operational status: Up
Reason: N/A
Hyperlocation NTP server: 9.0.0.4
Hyperlocation admin status: Enabled
Hyperlocation detection threshold: -100 dBm
Hyperlocation trigger threshold: 11
Hyperlocation reset threshold: 9

Note

For Hyperlocation to be operational, the following conditions must be met:

At least one Cisco CMX with Hyperlocation enabled
Hyperlocation admin state operational
Either AP NTP or IOS NTP configured

This example shows how to view detailed information about Hyperlocation configuration for an AP group:

Device# show ap group my-ap-group hyperlocation detail

Site Name: my-ap-group
Site Description: This is an AP group
Hyperlocation operational status: Up
Reason: N/A
Hyperlocation NTP server: 9.0.0.4
Hyperlocation admin status: Enabled
Hyperlocation detection threshold: -100 dBm
Hyperlocation trigger threshold: 11
Hyperlocation reset threshold: 9

Values for APs in all AP Groups:

AP Name                 Radio MAC        Method    Hyperlocation
----------------------------------------------------------------
APf07f.0635.2d40        f07f.0676.3b89   WSM       Enabled
APf4cf.e272.4ed0        f4cf.e223.ba31   Local     Enabled

show history channel interface dot11Radio all

To check channel change or trigger reason and history, use the show history channel interface dot11Radio all command.

show history channel interface dot11Radio all

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.2.1	This command was introduced.

Examples

This example shows how to check channel change or trigger reason and history:

Device# show history channel interface dot11Radio all

               Timestamp Slot Client count Channel Trigger
Fri May 31 12:57:04 2019    0            0      11 RRM-DCA
Fri May 31 13:10:02 2019    0            0       1 RRM-DCA
Fri May 31 12:57:04 2019    1            0      60  Manual
Fri May 31 13:00:16 2019    1            0     149     DFS

show ap hyperlocation

To view a summary or detailed information about the hyperlocation configuration, use the show ap hyperlocation command.

show ap hyperlocation { summary|detail}

Syntax Description


summary	Shows the overall configuration and operational values.
detail	Shows the overall configuration and operation values as well as detailed information about each AP.

Command Default

None

Command History


Release	Modification
Cisco IOS XE Denali 16.2.1	This command was introduced.
Cisco IOS XE Denali 16.3.1	This command was modified. The ble-beacon keyword was added.

Usage Guidelines

For hyperlocation to be operational, the following conditions must be met:

At least one Cisco Connected Mobile Experiences (CMX) must be present with hyperlocation enabled.
The hyperlocation admin state should be operational.
Either AP Network Time Protocol (NTP) or IOS NTP should be configured.

Examples

This example shows how to view a summary of the hyperlocation configuration:

Device# show ap hyperlocation summary

Hyperlocation operational status: Up
Hyperlocation NTP server currently used: 9.0.0.4
Hyperlocation admin status: Enabled
Hyperlocation detection threshold: -100 dBm
Hyperlocation trigger threshold: 10
Hyperlocation reset threshold: 8

This example shows how to view detailed information about hyperlocation configuration:

Device# show ap hyperlocation detail

Hyperlocation operational status: Up
Hyperlocation NTP server currently used: 9.0.0.4
Hyperlocation admin status: Enabled
Hyperlocation detection threshold: -100 dBm
Hyperlocation trigger threshold: 10
Hyperlocation reset threshold: 8

AP Name                 Radio MAC        Method    Hyperlocation
----------------------------------------------------------------
AP84b8.0252.b930        84b8.0216.c721   HALO      Enabled
AP84b8.0265.5540        84b8.0243.8796   WSM       Enabled
APf07f.0635.2d40        f07f.0676.3b89   WSM       Enabled
APf4cf.e272.4ed0        f4cf.e223.ba31   HALO      Enabled

show ap hyperlocation cmx summary

To see a summary of CMX informaiton with Hyperlocation enabled, use the show ap hyperlocation cmx summary command.

show ap hyperlocation cmx summary [ chassis {chassis-number | active | standby} R0]

Syntax Description


`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the AP filters in Route-processor slot 0.
standby R0	Standby instance of the AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see a summary of CMX informaiton with Hyperlocation enabled:

Device# show ap hyperlocation cmx summary

show ap image

To display the images present on Cisco lightweight access points, use the show ap image command.

show ap image

Syntax Description


This command has no keywords and arguments.

Command Default

None

Command Modes

Any command mode

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to display images on the access points:

Device# show ap image

show ap image file summary

To see the summary of an access point's (AP) software install files, use the show ap image file summary command.

show ap image file summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.4.1	This command was modified.

Examples

The following example shows how to display the summary of an AP's software install files:

Device# show ap image file summary
AP Image Active List
============================
Install File Name: base_image.bin
-------------------------------
AP Image Type    Capwap Version	Size (KB)	Supported AP models
--------------------------------------------------------------------------------------------------------
     ap1g1       17.3.0.30	      13300		NA

     ap1g2       17.3.0.30		34324	      NA

     ap1g3       17.3.0.30		98549	      AP803
	
     ap1g4       17.3.0.30	       34324	      AP1852E, AP1852I, AP1832I, AP1830I, AP1810W, OEAP1810
		
     ap1g5       17.3.0.30	       23492	      AP1815W, AP1815T, OEAP1815, AP1815I, AP1800I, AP1800S, AP1815M, 1542D, AP1542I, AP1100AC, AP1101AC, AP1840I
	
     ap1g6       17.3.0.30		93472             AP2900I, C9117AXI

    ap1g6a       17.3.0.30		 247377           C9130AXI, C9130AXE, C9140AXI, C9140AXD, C9140AXT

     ap1g7       17.3.0.30		 23988            AP1900I, C9115AXI, AP1900E, C9115AXE, C9120AXE, C9120AXP, C9120AXI
	
     ap1g8       17.3.0.30		 23473	     C9105AXI, C9105AXW, C9110AXI, C9110AXE

     ap3g1       17.3.0.30		 23422	      NA

     ap3g2       17.3.0.30		 23411		AP1702I

     ap3g3       17.3.0.30		 23090		AP3802E, AP3802I, AP3802P, AP4800, AP2802E, AP2802I, AP2802H, AP3800, AP1562E, AP1562I, AP1562D, AP1562PS, IW-6300H-DC, IW-6300H-AC, IW-6300H-DCW, ESW-6300
	
     c1570       17.3.0.30		 13000		AP1572E, 1573E, AP1572I

     c3700       17.3.0.30		 14032		AP3702E, AP3701E, AP3701I, AP3702I, AP3701P, AP3702P, AP2702E, AP2702I, AP3702, IW3702, AP3701, AP3700C

 virtApImg       17.3.0.30               177056	      APVIRTUAL


AP Image Prepare List**
============================
Install File Name: base_image.bin
-------------------------------
============================
Install File Name: base_image.bin
-------------------------------
AP Image Type    Capwap Version	Size (KB)	Supported AP models
----------------------------------------------------------------------------------------
     ap1g1       17.3.0.30	       13300		NA

     ap1g2       17.3.0.30		34324		NA

     ap1g3       17.3.0.30		98549		AP803
	
     ap1g4       17.3.0.30	       34324		AP1852E, AP1852I, AP1832I, AP1830I, AP1810W, OEAP1810
		
     ap1g5       17.3.0.30	       23492		AP1815W, AP1815T, OEAP1815, AP1815I, AP1800I, AP1800S, AP1815M, 1542D, AP1542I, AP1100AC, AP1101AC, AP1840I
	
     ap1g6       17.3.0.30		93472               AP2900I, C9117AXI

    ap1g6a       17.3.0.30		247377              C9130AXI, C9130AXE, C9140AXI, C9140AXD, C9140AXT

     ap1g7       17.3.0.30		23988                AP1900I, C9115AXI, AP1900E, C9115AXE, C9120AXE, C9120AXP, C9120AXI
    
     ap1g8       17.3.0.30		23473		  C9105AXI, C9105AXW, C9110AXI, C9110AXE

     ap3g1       17.3.0.30		23422		   NA

     ap3g2       17.3.0.30		23411		   AP1702I

     ap3g3       17.3.0.30		23090		   AP3802E, AP3802I, AP3802P, AP4800, AP2802E, AP2802I, AP2802H, AP3800, AP1562E, AP1562I, AP1562D, AP1562PS, IW-6300H-DC, IW-6300H-AC, IW-6300H-DCW, ESW-6300
	
     c1570       17.3.0.30		13000		   AP1572E, 1573E, AP1572I

     c3700       17.3.0.30		14032		   AP3702E, AP3701E, AP3701I, AP3702I, AP3701P, AP3702P, AP2702E, AP2702I, AP3702, IW3702, AP3701, AP3700C

 virtApImg       17.3.0.30              177056		   APVIRTUAL

**Difference of Active and Prepare list gives images being predownloaded to Access Points.

show ap image site summary

To see the summary of an access point's (AP) site-filtered upgrades, use the show ap image site summary command.

show ap image site summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

The following example shows how to display the summary of an AP's site-filtered upgrades:

Device# show ap image site summary 

Image name: smu1.bin
Site Tag               Prepared              Activated             Committed
-----------------------------------------------------------------------------------------------------------------
BGL18                   yes                        ongoing               no
BGL17                   yes                        ongoing               no

show ap iot-radio firmware summary

To display the IoT radio firmware information summary of the access point, use the show ap iot-radio firmware summary command.

show ap iot-radio firmware summary

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.7.1	This command was introduced.

Examples

This example shows you how to display the IoT radio firmware information summary of the access point:

Device# show ap iot-radio firmware summary

show ap link-encryption

To display the link encryption status, use the show ap link-encryption command.

show ap link-encryption [chassis | | {chassis-number | active | standby} | | R0]

Syntax Description


`chassis-number`	Chassis number as either 1 or 2.
active R0	Active instance in Route-processor slot 0.
standby R0	Standby instance in Route-processor slot 0.

Command Default

None

Command Modes

Any command mode

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example show how to display the link-encryption status:

Device# show Cisco IOS XE Gibraltar 16.12.2s link-encryption

show ap lldp neighbors detail

To view the details of the AP Link Layer Discovery Protocol (LLDP) neighbor information on the controller, when the AP is connected to the third-party switch.

show ap lldp neighbors detail

Syntax Description


This command has no arguments.

Command Default

None

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.5.1	This command was introduced.

Usage Guidelines

None

Examples

The following example shows how to view the details of AP Link Layer Discovery Protocol (LLDP) neighbor information on the controller, when the AP is connected to the third-party switch:

Device# show ap lldp neighbors detail
Number of neighbors: 1
AP Name               : 9130-ap1
AP Interface          : GigabitEthernet0
--------------------------------------------------------
Neighbor MAC          : c89c.1db1.1f80
Neighbor Name         : flex-ctlr-switch
System Description    : Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 15.2(4)E6, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2018 by Cisco Systems, Inc.
Compiled Thu 05-Apr-18 02:22 by prod_rel_team
Port ID               : Gi1/0/15
Port Description      : 9130-ap2
Chassis Alias         :
Management Addresses  :
  IPv4 address         : None
  IPv6 address         : None
Capabilities          :
  Bridge
  Router
Last updated time     : 12/02/2020 09:15:48

show ap lldp neighbors

To view the AP Link Layer Discovery Protocol (LLDP) neighbor information on the controller, when the AP is connected to the third-party switch.

show ap lldp neighbors

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.5.1	This command was introduced.

Usage Guidelines

None

Examples

The following example shows how to view the AP Link Layer Discovery Protocol (LLDP) neighbor information on the controller, when the AP is connected to the third-party switch:

Device# show ap lldp neighbors
Capability Codes:
     (R) Router, (B) Bridge, (T) Telephone, (C) DOCSIS Cable Device
     (W) WLAN Access Point, (P) Repeater, (S) Station, (O) Other


AP Name   AP Interface      Neighbor Name Neighbor MAC    Port ID    Mgmt. Address Capabilities  Last updated time
------------------------------------------------------------------------------------------------------------------
9130-ap1  GigabitEthernet0  switch        cxxc.1dxx.1fxx  Gi1/0/15   None          B R         12/02/2020 09:15:48

9117-ap1  GigabitEthernet0  switch        cxxc.1dxx.1fxx  Gi1/0/19   None          B R         12/02/2020 09:15:47

show ap name dot11 neighbor summary

To view the neighbor summary of an access point (AP) in a 802.11 2.4-GHz, 5-GHz, or a 6-GHz network, use the show ap name ap-name dot11 {24ghz | 5ghz | 6ghz} neighbor summary command.

show ap name dot11 {24ghz | 5ghz | 6ghz} neighbor summary

Syntax Description


`ap-name`	Specifies the Name of the AP.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.7.1	This command was introduced.

Examples

This example shows how to view the neighbor summary of the 802.11 2.4-GHz parameter:


Device# show ap name AP687D.B45C.0554 dot11 24ghz neighbor summary 

BSSID            Channel Channel-width Slot  RSSI  Last-Heard           SSID       Neighbor
-------------------------------------------------------------------------------------------
10f9.2077.6140     1      20 Mhz        0    -28   06/23/2021 01:42:51  mdns-psk   TRUE
10f9.2077.614f     1      20 Mhz        0    -28   06/23/2021 01:42:51  mdns-psk   TRUE
00b0.e192.9600    11      20 Mhz        0    -31   06/23/2021 01:42:51  mdns-psk   TRUE
00b0.e192.960f    11      20 Mhz        0    -31   06/23/2021 01:42:51  mdns-psk   TRUE
00ee.ab18.bf0f     6      20 Mhz        0    -38   06/23/2021 01:42:51  mdns-psk   TRUE
f4db.e69f.8860     1      20 Mhz        0    -75   06/23/2021 01:43:06  wlan1      FALSE
68ca.e43f.b902     1      20 Mhz        0    -77   06/23/2021 01:43:06  amaz-open  FALSE
68ca.e43f.b900     1      20 Mhz        0    -78   06/23/2021 01:43:06  amaz-web   FALSE
68ca.e43f.b903     1      20 Mhz        0    -78   06/23/2021 01:43:06  amaz-8021x FALSE

This example shows how to view the neighbor summary of the 802.11 5-GHz parameter:


Device# show ap name AP1117Q.B22U.0221 dot11 5ghz neighbor summary 

BSSID          Channel  Channel-width  Slot RSSI Last-Heard          SSID     Neighbor
--------------------------------------------------------------------------------------

7872.5dee.496f  100      80 Mhz         1    34   6/23/2021 01:43:35 mdns-psk  FALSE

This example shows how to view the neighbor summary of the 802.11 6-GHz parameter:


Device# show ap name AP1117Q.B22U.0221 dot11 6ghz neighbor summary

BSSID          Channel  Channel-width  Slot  RSSI  Last-Heard           SSID      Neighbor
------------------------------------------------------------------------------------------

687d.b45e.4c53    1        20 Mhz        3   -37   06/23/2021 01:42:51  wpa3-6ghz  TRUE
687d.b45e.53d3    1        20 Mhz        3   -39   06/23/2021 01:42:51  wpa3-6ghz  TRUE

show ap name lldp neighbors detail

To view the details of the AP Link Layer Discovery Protocol (LLDP) neighbor information on the controller, for a specific AP, when the AP is connected to the third-party switch.

show ap name ap-name lldp neighbors detail

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.5.1	This command was introduced.

Usage Guidelines

None

Examples

The following example shows how to view the details of the AP Link Layer Discovery Protocol (LLDP) neighbor information on the controller, for a specific AP, when the AP is connected to the third-party switch:

Device# show ap name 9130-ap1 lldp neighbors detail
AP Name               : 9130-ap1
AP Interface          : GigabitEthernet0
--------------------------------------------------------
Neighbor MAC          : c89c.1db1.1f80
Neighbor Name         : flex-ctlr-switch
System Description    : Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 15.2(4)E6, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2018 by Cisco Systems, Inc.
Compiled Thu 05-Apr-18 02:22 by prod_rel_team
Port ID               : Gi1/0/15
Port Description      : 9130-ap2
Chassis Alias         :
Management Addresses  :
  IPv4 address         : None
  IPv6 address         : None
Capabilities          :
  Bridge
  Router
Last updated time     : 12/02/2020 09:15:48

show ap name lldp neighbors

To view the AP Link Layer Discovery Protocol (LLDP) neighbor information on the controller, for a specific AP, when the AP is connected to the third-party switch.

show ap name ap-name lldp neighbors

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.5.1	This command was introduced.

Usage Guidelines

None

Examples

The following example shows how to view the AP Link Layer Discovery Protocol (LLDP) neighbor information on the controller, for a specific AP, when the AP is connected to the third-party switch:

Device# show ap name 9130-ap1 lldp neighbors
AP Name               : 9130-ap1
AP Interface          : GigabitEthernet0
--------------------------------------------------------
Neighbor MAC          : c89c.1db1.1f80
Neighbor Name         : flex-ctlr-switch
System Description    : Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 15.2(4)E6, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2018     by Cisco Systems, Inc.
Compiled Thu 05-Apr-18 02:22  02:22 by prod_rel_team
Port ID               : Gi1/0/15
Port Description      : 9130-ap2
Chassis Alias         :
Management Addresses  :
  IPv4 address         : None
  IPv6 address         : None
Capabilities          :
  Bridge
  Router
Last updated time     : 12/02/2020 09:15:48

show ap name ntp status

To display the Network Time Protocol (NTP) status of an AP, use the show ap name ntp status command.

show ap name ap-name ntp status

Syntax Description


`ap-name`	AP name.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Examples

The following example shows how to view the NTP status of an AP:

Device# show ap name AP-G1-230 ntp status

ap-name       enabled v4/v6 IPAddress       Status     Stratum LastSync  SyncOffset
AP-G1-230     Y       v4    198.51.100.5    AuthFail   4       1000      100

show ap ntp status

To display the Network Time Protocol (NTP) status for all the APs, use the show ap name ntp status command.

show ap ntp status

Syntax Description


This command has no keywords and arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Examples

The following example shows how to view the NTP status for all the APs:

Device# show ap ntp status

ap-name       enabled    v4/v6 IPAddress       Status   Stratum LastSync SyncOffset
AP-G1-230         Y      v4    198.51.100.5    AuthFail 2       Never     
AP-G1-231         Y      v4    198.51.100.10   Synced   3       1000     100
AP-G1-232         Y      v4    198.51.100.15   Synced   16      2000     50

show ap primary list

To see the AP primary list, use the show ap primary list command.

show ap primary list [ chassis | | { chassis-number | active | standby } | | R0 ]

Syntax Description


`chassis-number`	Chassis number as either 1 or 2.
active R0	Active instance in Route-processor slot 0.
standby R0	Standby instance in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the AP primary list:

Device# show ap primary list

show ap mesh cac access

To view the number of active calls on access radio for a given AP and its Mesh tree, use show ap mesh cac access command.

show ap ap-name mesh cac access

Syntax Description


`ap-name`	Name of the access point.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Usage Guidelines

Examples

This example shows how to display the number of active calls on access radio for a given AP and its Mesh tree:

Device# show ap <ap-name> mesh cac access

Depth   AP Name                           Slot  Radio      BW Used  Call
------  --------------------------------  ----  ---------  -------  ----
0       AALUKKAL-1562-RAP                 0     802.11b/g  0        0   
                                          1     802.11a    0        0   
1       AP380E.4DBF.C6B0                  0     802.11b/g  1072     2   
                                          1     802.11a    0        0

show ap mesh cac bwused voice

To view the voice bandwidth utilization of a given AP and its Mesh tree, use the show ap mesh cac bwused voice command.

show ap ap-name mesh cac bwused voice

Syntax Description


`ap-name`	Name of the access point.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Usage Guidelines

Examples

This example shows how to display the voice bandwidth utilization of a given AP and its Mesh tree:

Device# show ap <ap-name> mesh cac bwused voice

Depth   AP Name                           Slot  Radio      BW Used
------  --------------------------------  ----  ---------  -------
1       APA023.9FA9.D920                  0     802.11b/g  1140  
                                          1     802.11a    0     
2       AP380E.4DBF.C80C                  0     802.11b/g  570   
                                          1     802.11a    2144  
2       AP380E.4DBF.C816                  0     802.11b/g  0     
                                          1     802.11a    0     
2       APA023.9FA9.B702                  0     802.11b/g  0     
                                          1     802.11a    0

show ap mesh cac callpath

To view the number of active calls in access as well as backhaul for a given AP and its Mesh tree, use the show ap mesh cac callpath command.

show ap ap-name mesh cac callpath

Syntax Description


`ap-name`	Name of the access point.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Usage Guidelines

Examples

This example shows how to display the number of active calls in access as well as backhaul for a given AP and its Mesh tree:

Device# show ap <ap-name> mesh cac callpath

Depth   AP Name                           Slot  Radio      Call
------  --------------------------------  ----  ---------  ----
1       APA023.9FA9.D920                  0     802.11b/g  2   
                                          1     802.11a    0   
2       AP380E.4DBF.C80C                  0     802.11b/g  0   
                                          1     802.11a    2   
2       AP380E.4DBF.C816                  0     802.11b/g  0   
                                          1     802.11a    0   
2       APA023.9FA9.B702                  0     802.11b/g  0   
                                          1     802.11a    0

show ap mesh cac rejected

To view the number of rejected calls on access as well as backhaul for a given AP and its Mesh tree, use show ap mesh cac rejected command.

show ap ap-name mesh cac rejected

Syntax Description


`ap-name`	Name of the access point.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Usage Guidelines

Examples

This example shows how to display the number of rejected calls on access as well as backhaul for a given AP and its Mesh tree:

Device# show ap <ap-name> mesh cac rejected

show ap monitor-mode summary

To display the current channel-optimized monitor mode settings, use the show ap monitor-mode summary command.

show ap monitor-mode summary

Syntax Description


This command has no keywords and arguments.

Command Default

None

Command Modes

Any command mode

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to display current channel-optimized monitor mode settings:

Device# show ap monitor-mode summary

AP Name Ethernet MAC      Status   Scanning Channel List
------- -------------     -------- -------- ----------------
AP_004  xx:xx:xx:xx:xx:xx Tracking 1,6,11,  4

show ap multicast mom (multicast over multicast)

To confirm if the APs receive multicast to multicast (mom) traffic sent by the controller, using CAPWAP multicast group, use the show ap multicast mom command.

Syntax Description


This command has no keywords and arguments.

Command Default

None

Command Modes

Previleged EXEC

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.2	This command was introduced.

Examples

This example shows how to confirm if the APs receive multicast to multicast traffic sent by the controller using CAPWAP multicast group:

Device# show ap multicast mom

AP Name                    MOM-IP     TYPE MOM- STATUS
------------------------------------------------------
SS-E-1                     IPv4             Up
SS-E-2                     IPv4             Up
9130E-r3-sw2-g1012         IPv4             Up
9115i-r3-sw2-te1-0-38      IPv4             Up
AP9120-r3-sw3-Gi1-0-46     IPv4             Up
ap3800i-r2-sw1-te2-0-2     IPv4             Up

show ap name ap-name neighbor summary

To view the summary of AP neighbor information, use the show ap name ap-name neighbor summary

show ap name ap-name neighbor summary

Syntax Description


`ap-name`	Specifies the name of the AP whose neighbor summary is displayed.

Command Default

None

Command Modes

Privileged EXEC(#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.2.1	This command was introduced.

Examples

This example shows how to display the AP neighbor information:

Device#show ap name APXXXX.6DXX.59XX neighbor summary

BSSID                  Channel   Channel-width Slot        RSSI               Last-Heard                          SSID                                       Neighbour          
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
0008.2f1c.8040         1         20 Mhz        0           -39                03/17/2020 18:25:14                 aprusty-un-dot1x                           FALSE              
0008.2f1c.8041         1         20 Mhz        0           -39                03/17/2020 18:25:14                 aprusty-sim-11                             FALSE              
0008.2f1c.8042         1         20 Mhz        0           -39                03/17/2020 18:25:14                 one-ph                                     FALSE              
0008.2f1c.8044         1         20 Mhz        0           -38                03/17/2020 18:25:14                 aprusty-test                               FALSE              
0008.3296.f340         11        20 Mhz        0           -51                03/18/2020 10:39:27                 ewlc-ap-dot1x                              FALSE              
0008.3296.f341         11        20 Mhz        0           -49                03/18/2020 10:39:27                 vewlc_small_psk                            FALSE              
002a.1022.d950         1         20 Mhz        0           -57                03/17/2020 18:25:14                 ewlc-ap-dot1x                              FALSE              
002a.105c.bfd0         1         20 Mhz        0           -36                03/17/2020 18:25:14                 ewlc-ap-dot1x                              FALSE              
002a.105c.bfd1         1         20 Mhz        0           -37                03/17/2020 18:25:14                 vewlc_small_psk                            FALSE              
002c.c864.76d0         11        20 Mhz        0           -61                03/18/2020 10:37:37                 rajwlan                                    FALSE              

BSSID                  Channel   Channel-width Slot        RSSI               Last-Heard                          SSID                                       Neighbour          
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
002c.c8de.59e0         1         20 Mhz        0           -48                03/17/2020 18:25:14                 WQ                                         FALSE              
002c.c8de.5d80         11        20 Mhz        0           -54                03/18/2020 10:39:27                 ewlc-ap-dot1x                              FALSE              
002c.c8de.5d81         11        20 Mhz        0           -55                03/18/2020 10:39:27                 vewlc_small_psk                            FALSE              
002c.c8de.7260         11        20 Mhz        0           -53                03/18/2020 10:39:27                 ewlc-ap-dot1x                              FALSE              
002c.c8de.7261         11        20 Mhz        0           -54                03/18/2020 10:39:27                 vewlc_small_psk                            FALSE              
005d.7390.e1e0         1         20 Mhz        0           -54                03/17/2020 18:25:14                 rlan                                       FALSE              
006b.f114.95a0         1         20 Mhz        0           -60                03/17/2020 18:25:14                 zavc                                       FALSE              
006b.f114.b0e0         1         20 Mhz        0           -46                03/17/2020 18:25:14                 ewlc-ap-dot1x                              FALSE              
006c.bc61.2340         1         20 Mhz        0           -63                03/17/2020 18:24:44                 dnac-swim                                  FALSE              
006c.bc72.5ce0         11        20 Mhz        0           -58                03/18/2020 10:39:17                 dnac-swim                                  FALSE

show ap name auto-rf

To display the auto-RF settings for a Cisco lightweight access point, use the show ap name auto-rf command.

show ap name ap-name auto-rf dot11 {24ghz | 5ghz | dual-band}

Syntax Description


`ap-name`	Name of the Cisco lightweight access point.
24ghz	Displays the 2.4 GHz band.
5ghz	Displays the 5 GHz band.
dual-band	Displays dual band.

Command Default

None

Command Modes

Privileged EXEC.

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to display auto-RF information for an access point:

Device# show ap name AP01 auto-rf dot11 24ghz

Number of Slots                                  : 2
AP Name                                          : TSIM_AP-1
MAC Address                                      : 0000.2000.02f0
Slot ID                                          : 0
Radio Type                                       : 802.11b/g
Subband Type                                     : All

Noise Information
  Noise Profile                                  : Failed
  Channel   1                                     :   24 dBm
  Channel   2                                     :   48 dBm
  Channel   3                                     :   72 dBm
  Channel   4                                     :   96 dBm
  Channel   5                                     :  120 dBm
  Channel   6                                     : -112 dBm
  Channel   7                                     :  -88 dBm
  Channel   8                                     :  -64 dBm
  Channel   9                                     :  -40 dBm
  Channel  10                                     :  -16 dBm
  Channel  11                                     :    8 dBm

Interference Information
  Interference Profile                           : Passed
  Channel   1                                     : -128 dBm @  0% busy
  Channel   2                                     :  -71 dBm @  1% busy
  Channel   3                                     :  -72 dBm @  1% busy
  Channel   4                                     :  -73 dBm @  2% busy
  Channel   5                                     :  -74 dBm @  3% busy
  Channel   6                                     :  -75 dBm @  4% busy
  Channel   7                                     :  -76 dBm @  5% busy
  Channel   8                                     :  -77 dBm @  5% busy
  Channel   9                                     :  -78 dBm @  6% busy
  Channel  10                                     :  -79 dBm @  7% busy
  Channel  11                                     :  -80 dBm @  8% busy

Rogue Histogram (20/40_ABOVE/40_BELOW)
    Channel  36                                   : 27/ 4/ 0
    Channel  40                                   : 13/ 0/ 0
    Channel  44                                   :  5/ 0/ 0
    Channel  48                                   :  6/ 0/ 1
    Channel  52                                   :  4/ 0/ 0
    Channel  56                                   :  5/ 0/ 0
    Channel  60                                   :  1/ 3/ 0
    Channel  64                                   :  3/ 0/ 0
    Channel 100                                   :  0/ 0/ 0
    Channel 104                                   :  0/ 0/ 0
    Channel 108                                   :  0/ 1/ 0

Load Information
  Load Profile                                   : Passed
  Receive Utilization                            : 10%
  Transmit Utilization                           : 20%
  Channel Utilization                            : 50%
  Attached Clients                               : 0 clients

Coverage Information
  Coverage Profile                               : Passed
  Failed Clients                                 : 0 clients

Client Signal Strengths
  RSSI -100 dBm                                  : 0 clients
  RSSI  -92 dBm                                  : 0 clients
  RSSI  -84 dBm                                  : 0 clients
  RSSI  -76 dBm                                  : 0 clients
  RSSI  -68 dBm                                  : 0 clients
  RSSI  -60 dBm                                  : 0 clients
  RSSI  -52 dBm                                  : 0 clients

Client Signal to Noise Ratios
  SNR    0 dB                                    : 0 clients
  SNR    5 dB                                    : 0 clients
  SNR   10 dB                                    : 0 clients
  SNR   15 dB                                    : 0 clients
  SNR   20 dB                                    : 0 clients
  SNR   25 dB                                    : 0 clients
  SNR   30 dB                                    : 0 clients
  SNR   35 dB                                    : 0 clients
  SNR   40 dB                                    : 0 clients
  SNR   45 dB                                    : 0 clients

Nearby APs
  AP 0000.2000.0300 slot 0                       : -68 dBm on  11 (10.10.10.1)
  AP 0000.2000.0400 slot 0                       : -68 dBm on  11 (10.10.10.1)
  AP 0000.2000.0600 slot 0                       : -68 dBm on  11 (10.10.10.1)

Radar Information

Channel Assignment Information
  Current Channel Average Energy                 : 0 dBm
  Previous Channel Average Energy                : 0 dBm
  Channel Change Count                           : 0
  Last Channel Change Time                       : Wed Oct 17 08:13:36 2012
  Recommended Best Channel                       : 11

RF Parameter Recommendations
  Power Level                                    : 1
  RTS/CTS Threshold                              : 2347
  Fragmentation Threshold                        : 2346
  Antenna Pattern                                : 0

Persistent Interference Devices

show ap name ble detail

To display BLE management details, use the show ap name ble detail command.

show ap name ap-name ble detail

Syntax Description


`ap-name`	Specifies the name of the AP.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.3.1	This command was introduced.

Usage Guidelines

None

Examples

The following example shows how to display the BLE management details:

Device(config)# show ap name ap-name ble detail

show ap name cablemodem

To see cable modem information of an AP, use the show ap name ap-name cablemodem command.

show ap name ap-name cablemodem [ chassis {chassis-number | active | standby} R0]

Syntax Description


`ap-name`	Name of the AP.
`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the AP filters in Route-processor slot 0.
standby R0	Standby instance of the AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see cable modem information of an AP:

Device# show ap name my-ap cablemodem

show ap name config

To display common information and Ethernet VLAN tagging information for a specific Cisco lightweight access point, use the show ap name config command.

show ap name ap-name config {ethernet | general}

Syntax Description


`ap-name`	Name of the Cisco lightweight access point.
ethernet	Displays Ethernet tagging configuration information for an access point.
general	Displays common information for an access point.

Command Default

None

Command Modes

Any command mode

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to display Ethernet tagging information for an access point:

Device# show ap name AP01 config ethernet

VLAN Tagging Information for AP01

This example shows how to display common information for an access point:

Device# show ap name AP01 config general

Cisco AP Name                                   : AP01
Cisco AP Identifier                             : 5
Country Code                                    : US  - United States
Regulatory Domain Allowed by Country            : 802.11bg:-A     802.11a:-A
AP Country Code                                 : US  - United States
AP Regulatory Domain                            : Unconfigured
Switch Port Number                              : Te1/0/1
MAC Address                                     : 0000.2000.02f0
IP Address Configuration                        : Static IP assigned
IP Address                                      : 10.10.10.12
IP Netmask                                      : 255.255.0.0
Gateway IP Address                              : 10.10.10.1
Fallback IP Address Being Used                  : 10.10.10.12
Domain                                          : Cisco
Name Server                                     : 0.0.0.0
CAPWAP Path MTU                                 : 1485
Telnet State                                    : Enabled
SSH State                                       : Disabled
Cisco AP Location                               : sanjose
Cisco AP Group Name                             : default-group
Primary Cisco Controller Name                   : CAPWAP Controller
Primary Cisco Controller IP Address             : 10.10.10.1
Secondary Cisco Controller Name                 :
Secondary Cisco Controller IP Address           : Not Configured
Tertiary Cisco Controller Name                  :
Tertiary Cisco Controller IP Address            : Not Configured
Administrative State                            : Enabled
Operation State                                 : Registered
AP Mode                                         : Local
AP Submode                                      : Not Configured
Remote AP Debug                                 : Disabled
Logging Trap Severity Level                     : informational
Software Version                                : 7.4.0.5
Boot Version                                    : 7.4.0.5
Stats Reporting Period                          : 180
LED State                                       : Enabled
PoE Pre-Standard Switch                         : Disabled
PoE Power Injector MAC Address                  : Disabled
Power Type/Mode                                 : Power Injector/Normal Mode
Number of Slots                                 : 2
AP Model                                        : 1140AG
AP Image                                        : C1140-K9W8-M
IOS Version                                     :
Reset Button                                    :
AP Serial Number                                : SIM1140K001
AP Certificate Type                             : Manufacture Installed
Management Frame Protection Validation          : Disabled
AP User Mode                                    : Customized
AP User Name                                    : cisco
AP 802.1X User Mode                             : Not Configured
AP 802.1X User Name                             : Not Configured
Cisco AP System Logging Host                    : 255.255.255.255
AP Up Time                                      : 15 days 16 hours 19 minutes 57
 seconds
AP CAPWAP Up Time                               : 4 minutes 56 seconds
Join Date and Time                              : 10/18/2012 04:48:56
Join Taken Time                                 : 15 days 16 hours 15 minutes 0
seconds
Join Priority                                   : 1
Ethernet Port Duplex                            : Auto
Ethernet Port Speed                             : Auto
AP Link Latency                                 : Disabled
Rogue Detection                                 : Disabled
AP TCP MSS Adjust                               : Disabled
AP TCP MSS Size                                 : 6146

show ap name config slot

To display the configuration of a Cisco AP and also display the common information for a slot, use the show ap name config slot command.

show ap name Cisco-ap-name slot 0-3

Syntax Description


`Cisco-ap-name`	Specifies the name of the Cisco AP.
`0-3`	Specifies the slot ID.

Command Default

None

Command Modes

Any command mode

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to display common information for a slot in an access point:

Device# show ap name Cisco-ap-name config slot 3

show ap name config ethernet

To see Ethernet related configuration information of an AP, use the show ap name ap-name config ethernet command.

show ap name ap-name config ethernet [ chassis {chassis-number | active | standby} R0]

Syntax Description


`ap-name`	Name of the AP.
`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the AP filters in Route-processor slot 0.
standby R0	Standby instance of the AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see Ethernet related configuration information of an AP:

Device# show ap name my-ap config ethernet

show ap name dot11

To display 802.11a or 802.11b configuration information that corresponds to specific Cisco lightweight access points, use the show ap name dot11 command.

show ap name ap-name dot11 { 24ghz | 5ghz | 6ghz } { ccx | cdp | profile | service-policy output | tsm { all | client-mac } }

Syntax Description


`ap-name`	Name of the Cisco lightweight access point.
24ghz	Displays the 2.4-GHz band.
5ghz	Displays the 5-GHz band.
6ghz	Displays the 6-GHz band.
ccx	Displays the Cisco Client eXtensions (CCX) radio management status information.
cdp	Displays Cisco Discovery Protocol (CDP) information.
profile	Displays configuration and statistics of 802.11 profiling.
service-policy output	Displays downstream service policy information.
tsm	Displays 802.11 traffic stream metrics statistics.
all	Displays the list of all access points to which the client has associations.
`client-mac`	MAC address of the client.
SI	Displays the SI configurations.
airtime-fairness	Displays the stats of 24Ghz or 5Ghz or 6-GHz airtime-fairness.
call-control	Displays the call control information.
radio-reset	Displays radio-reset.
slot	Displays slot information.
voice	Displays voice information.

Command Default

None

Command Modes

Any command mode

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.
Cisco IOS XE Cupertino 17.7.1	This command was modified to include 6-GHz band.

Examples

This example shows how to display the service policy that is associated with the access point:

Device# show ap name test-ap dot11 24ghz service-policy output 

Policy Name  : test-ap1
Policy State : Installed

This example shows how to display the CCX RRM 802.11 configuration for a specific access point:

Device# show ap name AP01 dot11 24ghz ccx

This example show how to display CDP information for a specific access point:

Device# show ap name AP01 dot11 24ghz cdp

AP Name               AP CDP State
--------------------- --------------
AP03                  Disabled

This example show how to display the configuration and statistics of 802.11b profiling for a specific access point:

Device# show ap name AP01 dot11 24ghz profile

 802.11b Cisco AP performance profile mode             : GLOBAL
 802.11b Cisco AP Interference threshold               : 10 %
 802.11b Cisco AP noise threshold                      : -70 dBm
 802.11b Cisco AP RF utilization threshold             : 80 %
 802.11b Cisco AP throughput threshold                 : 1000000 bps
 802.11b Cisco AP clients threshold                    : 12 clients

This example show how to display downstream service policy information for a specific access point:

Device# show ap name AP01 dot11 24ghz service-policy output

Policy Name  : def-11gn
Policy State : Installed

This example show how to display the traffic stream configuration for all clients that correspond to a specific access point:

Device# show ap name AP01 dot11 24ghz tsm all

show ap name environment

To see the AP environment information of an AP, use the show ap name ap-name environment command.

show ap name ap-name environment [ chassis {chassis-number | active | standby} R0]

Syntax Description


`ap-name`	Name of the AP.
`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the AP filters in Route-processor slot 0.
standby R0	Standby instance of the AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the AP environment information of an AP:

Device# show ap name my-ap environment

show ap name gps location

To see the GPS location of the AP, use the show ap name gps location command.

show ap name ap-name gps location[ {chassis-number | active | standby}R0

Syntax Description


`ap-name`	Name of the Access Point
gps	See the GPS information of a Cisco AP
location	Shows the Mesh linktest data
`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the active AP filters in Route-processor slot 0.
standby R0	Standby instance of the configuration in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the GPS location of an AP:

Device# show ap name mesh-profile-name gps location

show ap name grpc detail

To display the detailed status of gRPC channel from AP to Cisco DNA, use the show ap name grpc detail command.

show ap name ap-name grpc detail

Syntax Description


`ap-name`	Specifies the name of the AP.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.3.1	This command was introduced.

Usage Guidelines

None

Examples

The following example shows how to display the detailed status of gRPC channel from AP to Cisco DNA:

Device(config)# show ap name APXXXX.BXXX.FXXX grpc detail

show ap name hyperlocation

To view a summary or detailed information about the hyperlocation configuration for an access point (AP), use the show ap name hyperlocation command.

show ap name ap-name hyperlocation ble-beacon

Syntax Description


`ap-name`	Access point name.
hyperlocation	Displays AP hyperlocation information.
ble-beacon	Displays BLE beacon configuration of an AP.

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Denali 16.3.1	This command was introduced.

Examples

This example shows how to view the BLE beacon configuration of an AP:

Device# show ap name test-ap hyperlocation ble-beacon

ID  Major  Minor  TX Power(dBm)
-------------------------------
0   0      0      0              
1   0      0      0              
2   0      0      0             
3   0      0      0

show ap name mesh backhaul

To see mesh backhaul statistics of an AP, use the show ap name ap-name mesh backhaul command.

show ap name ap-name mesh backhaul [ chassis {chassis-number | active | standby} R0]

Syntax Description


`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the AP filters in Route-processor slot 0.
standby R0	Standby instance of the AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see mesh backhaul statistics of an AP:

Device# show ap name mymeshap mesh backhaul

show ap name mesh bhrate

To see mesh bachkhaul data rate for an AP, use the show ap name ap-name mesh bhrate command.

show ap name ap-name mesh bhrate [ chassis {chassis-number | active | standby} R0]


`ap-name`	Name of the AP.
`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the AP filters in Route-processor slot 0.
standby R0	Standby instance of the AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see mesh bachkhaul data rate for an AP:

Device# show ap name mymeshap mesh bhrate

show ap name mesh linktest

To see the mesh linktest data, use the show ap name mesh linktest data command.

show ap name ap-name mesh linktest data dest-mac [ chassis {chassis-number | active | standby}R0]

Syntax Description


`ap-name`	Name of the Access Point
linktest	Shows the Mesh linktest
data	Shows the Mesh linktest data
`dest-mac`	Enter the AP MAC address.
`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the configuration in Route-processor slot 0.
standby R0	Standby instance of the configuration in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the mesh linktest data of an AP:

Device# show ap name mesh-profile-namemesh linktest data 83-88-15-0C-83-72

show ap name mesh neighbor detail

To see detailed information about a neighbor of a mesh AP, use the show ap name ap-name mesh neighbor detail command.

show ap name ap-name mesh neighbor detail [ chassis {chassis-number | active | standby} R0]

Syntax Description


`ap-name`	Name of the AP.
`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the AP filters in Route-processor slot 0.
standby R0	Standby instance of the AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see detailed information about a neighbor of a mesh AP:

Device# show ap name mymeshap mesh neighbhor detail

show ap name mesh neighbor detail

To see detailed information about a neighbor of a mesh AP, use the show ap name ap-name mesh neighbor detail command.

show ap name ap-name mesh neighbor detail [ chassis {chassis-number | active | standby} R0]

Syntax Description


`ap-name`	Name of the AP.
`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the AP filters in Route-processor slot 0.
standby R0	Standby instance of the AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see detailed information about a neighbor of a mesh AP:

Device# show ap name mymeshap mesh neighbhor detail

show ap name mesh path

To see information about the mesh AP's path, use the show ap name ap-name mesh path command.

show ap name ap-name mesh path [ chassis {chassis-number | active | standby} R0]

Syntax Description


`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the AP filters in Route-processor slot 0.
standby R0	Standby instance of the AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see information about the mesh AP's path:

Device# show ap name mymeshap mesh path

show ap name mesh stats

To see mesh statistics, use the show ap name ap-name mesh stats command.

show ap name ap-name [packet error | queue | security]

Syntax Description


`ap-name`	Name of the AP.
packet error	Mesh packet error statistics.
queue	Mesh queue statistics.
security	Mesh security statistics.
`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the AP filters in Route-processor slot 0.
standby R0	Standby instance of the AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see mesh statistics:

Device# show ap name mymeshap mesh stats

show ap name tunnel eogre events

To display the Ethernet over GRE (EoGRE) events on an AP, use the show ap name tunnel eogre events command.

show ap name ap-name tunnel eogre events

Syntax Description


`ap-name`	AP name.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to display the EoGRE tunnel events on an AP:

Device# show ap name ap1 tunnel eogre events

AP 80e8.6fd4.9520  Event history
Timestamp               #Times   Event               RC Context
----------------------- -------- ------------------- -- ----------------------------------------
02/18/2019 23:50:26.341 6        IAPP_STATS           0 GW Tunnel2 uptime:0s                    
02/18/2019 23:49:40.222 2        CLIENT_JOIN          0 74da.3828.88b0, (eogre_domain/2121)     
02/18/2019 23:48:43.549 1        CLIENT_LEAVE         0 74da.3828.88b0, (eogre_domain/2121)     
02/18/2019 23:47:33.127 1        DOMAIN_STATUS        0 eogre_domain Active GW: Tunnel1         
02/18/2019 23:47:33.124 4        AP_TUNNEL_STATUS     0 Tunnel2 Dn                              
02/18/2019 23:47:33.124 1        MSG_CLIENT_DEL       0 GW Tunnel2 (IP: 9.51.1.12)              
02/18/2019 23:47:33.124 2        TUNNEL_ADD           0 GW Tunnel2                              
02/18/2019 23:47:33.120 3        MSG_CLIENT_DEL_PD    0 GW Tunnel1 (IP: 9.51.1.11)              
02/18/2019 23:47:31.763 2        AP_DOMAIN_PUSH       0 Delete:eogre_domain_set, 0 GWs          
02/18/2019 23:47:31.753 4        AP_VAP_PUSH          0 profile:'eogre_tunnel', wlan:pyats_eogre

show ap name tunnel eogre domain detailed

To display the detailed information of the Ethernet over GRE (EoGRE) tunnel domain status on an AP, use the show ap name tunnel eogre domain detailed command.

show ap name ap-name tunnel eogre domain detailed domain-name

Syntax Description


`ap-name`	AP name.
`domain-name`	EoGRE domain name.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to display the detailed information of the EoGRE tunnel domain status on an AP:

Device# show ap name ap1 tunnel eogre domain detailed eogre_domain


Domain Name    : eogre_domain
 Primary GW    : Tunnel1
 Secondary GW  : Tunnel2
 Active GW     : Tunnel1
 Redundancy    : Non-Revertive
 AdminState    : Up

show ap name tunnel eogre domain summary

To display the summary information of the Ethernet over GRE (EoGRE) tunnel domain on an AP, use the show ap name tunnel eogre domain summary command.

show ap name ap-name tunnel eogre domain summary

Syntax Description


`ap-name`	AP name.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to display the summary information of the EoGRE tunnel domain on an AP:

Device# show ap name ap1 tunnel eogre domain summary

AP MAC          Domain                           Active Gateway
-------------------------------------------------------------------------------
80e8.6fd4.9520  eogre_domain

show ap name tunnel eogre gateway detailed

To display the detailed information of the Ethernet over GRE (EoGRE) tunnel gateway status on an AP, use the show ap name tunnel eogre gateway detailed command.

show ap name ap-name tunnel eogre gateway detailed gateway-name

Syntax Description


`ap-name`	AP name.
`gateway-name`	EoGRE gateway name.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to display the detailed information of the EoGRE tunnel gateway status on an AP:

Device# show ap name ap1 tunnel eogre gateway detailed Tunnel2

Gateway : Tunnel2
 Mode   : IPv4
 IP     : 9.51.1.12
 State  : Down
 MTU    : 0
 AP MAC : 80e8.6fd4.9520

 Clients
  Total Number of Wireless Clients      : 0
 Traffic
  Total Number of Received Packets      : 0
  Total Number of Received Bytes        : 0
  Total Number of Transmitted Packets   : 0
  Total Number of Transmitted Bytes     : 0
  Total Number of Lost Keepalive        : 151

show ap name tunnel eogre gateway summary

To display the summary information of the Ethernet over GRE (EoGRE) tunnel gateway on an AP, use the show ap name tunnel eogre gateway summary command.

show ap name ap-name tunnel eogre gateway summary

Syntax Description


`ap-name`	AP name.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to display the summary information of the EoGRE tunnel gateway on an AP:

Device# show ap name ap1 tunnel eogre gateway summary


AP MAC          Gateway          Type  IP                                      State  Clients
---------------------------------------------------------------------------------------------
80e8.6fd4.9520  Tunnel1          IPv4  9.51.1.11                               Up     1     
80e8.6fd4.9520  Tunnel2          IPv4  9.51.1.12                               Down   0

show ap name wlan

To display the Basic Service Set Identifier (BSSID) value for each WLAN defined on an access point and to display WLAN statistics, use the show ap name wlan command.

show ap name ap-name wlan {dot11 {24ghz | 5ghz} | statistic}

Syntax Description


`ap-name`	Name of the Cisco lightweight access point.
dot11	Displays 802.11 parameters.
24ghz	Displays 802.11b network settings.
5ghz	Displays 802.11a network settings.
statistic	Displays WLAN statistics.

Command Default

None

Command Modes

Any command mode

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to display BSSID information of an access point in an 802.11b network:

Device# show ap name AP01 wlan dot11 24ghz

Site Name                                        : default-group
Site Description                                 :

WLAN ID  Interface  BSSID
-------------------------------------
1        default    00:00:20:00:02:00
12       default    00:00:20:00:02:0b

This example shows how to display WLAN statistics for an access point:

Device# show ap name AP01 wlan statistic

WLAN ID  : 1
WLAN Profile Name  : maria-open

   EAP Id Request Msg Timeouts           : 0
   EAP Id Request Msg Timeouts Failures  : 0
   EAP Request Msg Timeouts              : 0
   EAP Request Msg Timeouts Failures     : 0
   EAP Key Msg Timeouts                  : 0
   EAP Key Msg Timeouts Failures         : 0


WLAN ID  : 12
WLAN Profile Name  : 24

   EAP Id Request Msg Timeouts           : 0
   EAP Id Request Msg Timeouts Failures  : 0
   EAP Request Msg Timeouts              : 0
   EAP Request Msg Timeouts Failures     : 0
   EAP Key Msg Timeouts                  : 0
   EAP Key Msg Timeouts Failures         : 0

show ap name wlan vlan

To display the operational WLAN-VLAN mappings for each access point (AP), use the show ap name wlan vlan command.

show ap name ap_name wlan vlan

Syntax Description


`ap_name`	Name of the AP whose WLAN-VLAN mappings are to be displayed.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Examples

The following example shows the operational wlan vlan mappings for an AP:

Device# show ap name test wlan vlan

Policy tag mapping
------------------
WLAN Profile Name Name Policy    VLAN   Flex Central Switching  IPv4 ACL    IPv6 ACL
------------------------------------------------------------------------------------------
jey_cwa            pp-local-1     46       Enabled               jey_acl1   Not Configured
swaguest           pp-local-1     46       Enabled               jey_acl1   Not Configured

show ap name ble detail

To view the CMX associated with an AP, use the show ap name ble detail command.

show ap name ap-name ble detail

Syntax Description


`ap-name`	Specifies the name of the AP.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Usage Guidelines

Examples

This example shows how to display the global values for BLE and BLE details for a specific AP:

Device# show ap name AP4001.7AB2.C39A ble detail
CMX IP: 9.9.71.100
-----------------------
  BLE administrative status: Up
  BLE operational status: Up
  Scanning interval: 10

  AP Name                         Interface             Status
  ----------------------------------------------------------------
  AP4001.7AB2.C39A                Integrated            Open

show ap name temperature

To view the temperature information of an AP, use the show ap name temperature command.

show ap name ap-name temperature

Syntax Description


`ap-name`	AP name.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.3.1	This command was introduced.

Examples

This example shows how to view the temperature information of an AP:

Device# show ap name ap-3702 temperature

show ap management-mode meraki capability summary

To display the Meraki management mode capable AP information summary, use the show ap management-mode meraki capability summary

show ap management-mode meraki capability summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC(#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.9.1	This command was modified.

Examples

This example show how to display the Meraki management mode capable AP information summary:

Device# show ap management-mode meraki capability summary

show ap management-mode meraki change summary

To display the summary of the AP management mode meraki changes, use the show ap management-mode meraki change summary command.

show ap management-mode meraki change summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC(#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.9.1	This command was modified.

Examples

This example shows how to display the summary of the AP management mode meraki changes:

Device# show ap management-mode meraki change summary

show ap management-mode meraki failure summary

To display the Meraki management mode failure summary, use the show ap management-mode meraki failure summary command.

show ap management-mode meraki failure summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC(#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.9.1	This command was modified.

Examples

This example shows how to display the Meraki management mode failure summary:

Device# show ap management-mode meraki failure summary

show ap profile

To see overall status of Hyperlocation for an AP profile, use the show ap profile command.

show ap profile profile-name {detailed | hyperlocation {ble-beacon | detail | summary}} [ chassis {chassis-number | active | standby} R0]

Syntax Description


`profile-name`	AP profile name.
detailed	Shows the detailed parameters of the AP join profile.
hyperlocation	Shows Hyperlocation information for the AP profile.
ble-beacon	Show the list of configured BLE beacons for the AP profile.
detail	Shows detailed status of Hyperlocation for the AP profile.
summary	Shows overall status of Hyperlocation for the AP profile
`chassis-number`	Chassis number as either 1 or 2.
active R0	Active instance in Route-processor slot 0.
standby R0	Standby instance in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the overall status of Hyperlocation for an AP profile:

Device# show ap profile my-ap-profile detailed

show ap rf-profile name

To display the selected ap RF-Profile details, use the show ap rf-profile name command.

show ap rf-profile name profile-name detail

Syntax Description


`profile-name`	Name of the RF-Profile.
detail	Show detail of selected RF Profile.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Denali 16.3.1	This command was introduced.

Usage Guidelines

None

Examples

This example shows how to display the details of the selected RF-Profile.

Device#show ap rf-profile name doctest detail
Description :
AP Group Names :
RF Profile Name : doctest
Band : 2.4 GHz
802.11n client only : Disabled
Transmit Power Threshold v1: -70 dBm
Min Transmit Power: -10 dBm
Max Transmit Power: 30 dBm
Operational Rates
  802.11b 1M Rate : Mandatory
  802.11b 2M Rate : Mandatory
  802.11b 5.5M Rate : Mandatory
  802.11b 11M Rate : Mandatory
  802.11b 6M Rate : Mandatory
  802.11b 9M Rate : Supported
  802.11b 12M Rate : Supported
  802.11b 18M Rate : Supported
  802.11b 24M Rate : Supported
  802.11b 36M Rate : Supported
  802.11b 48M Rate : Supported
  802.11b 54M Rate : Supported
Max Clients : 200
Wlan name                        Max Clients
--------------------------------------------

Trap Threshold
  Clients:  12 clients
  Interference:  10%
  Noise:  -70 dBm
  Utilization:  80%
Multicast Data Rate: auto
Rx SOP Threshold : auto
Band Select
  Probe Response:  Disabled
  Cycle Count:  2 cycles
  Cycle Threshold:  200 milliseconds
  Expire Suppression:  20 seconds
  Expire Dual Band:  60 seconds
  Client RSSI:  -80 dBm
  Client Mid RSSI:  -80 dBm
Load Balancing
  Window:  5 clients
  Denial:  3 count
Coverage Data
  Data: -80 dBm
  Voice: -80 dBm
 Minimum Client Level: 3 clients
  Exception Level: 25%
DCA Channel List  : 1,5,9,13
DCA Foreign AP Contribution : Enabled
802.11n MCS Rates
  MCS 0 : Enabled
  MCS 1 : Enabled
  MCS 2 : Enabled
  MCS 3 : Enabled
  MCS 4 : Enabled
  MCS 5 : Enabled
  MCS 6 : Enabled
  MCS 7 : Enabled
  MCS 8 : Enabled
  MCS 9 : Enabled
  MCS 10 : Enabled
  MCS 11 : Enabled
  MCS 12 : Enabled
  MCS 13 : Enabled
  MCS 14 : Enabled
  MCS 15 : Enabled
  MCS 16 : Enabled
  MCS 17 : Enabled
  MCS 18 : Enabled
  MCS 19 : Enabled
  MCS 20 : Enabled
  MCS 21 : Enabled
  MCS 22 : Enabled
  MCS 23 : Enabled
  MCS 24 : Enabled
  MCS 25 : Enabled
  MCS 26 : Enabled
  MCS 27 : Enabled
  MCS 28 : Enabled
  MCS 29 : Enabled
  MCS 30 : Enabled
  MCS 31 : Enabled
State : Down

show ap rf-profile summary

To display the ap RF-Profile summary, use the show ap rf-profile summary command.

show ap rf-profile summary

Syntax Description


summary	Show summary of RF Profiles

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Denali 16.3.1	This command was introduced.

Usage Guidelines

None

Examples

This example shows how to display the ap RF-Profile summary .

Device#show ap rf-profile summary 
Number of RF Profiles : 1

RF Profile Name                   Band      Description           Applied   State
---------------------------------------------------------------------------------
doctest                           2.4 GHz                         No        Down

show ap sensor status

To display the details of the AP sensors and their status, use the show ap sensor status command.

show ap sensor status

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.8.1	This command was introduced.

Examples

The following example displays the details of the AP sensors and their status:

Device# show ap sensor status

show ap summary

To display the status summary of all Cisco lightweight access points attached to the device, use the show ap summary command.

show ap summary

Syntax Description


This command has no keywords and arguments.

Command Default

None

Command Modes

Any command mode

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

Use this command to display a list that contains each lightweight access point name, number of slots, manufacturer, MAC address, location, and the device port number.

Examples

This example shows how to display a summary of all connected access points:

Controller# show ap summary

Number of APs: 1

Global AP User Name: Cisco
Global AP Dot1x User Name: Not configured

AP Name                           AP Model  Ethernet MAC    Radio MAC       State         
----------------------------------------------------------------------------------------
3602a                             3502I     003a.99eb.3fa8  d0c2.8267.8b00  Registered

show ap summary load-info

To view the AP per radio channel utilization and the total number of clients and slots per AP, use the show ap summary load-info command.

show ap summary load-info

Syntax Description


This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.3.1	This command was introduced.

Examples

This example shows how to view the AP per radio channel utilization and the total number of clients and slots per AP:

Device# show ap summary load-info 

WTP-Mac         AP-Name          Tot-Slots Tot-Clients  Slot0                  Slot1                   Slot2
                                                        Clients Utilisation(%) Clients Utilisation(%)  Clients Utilisation(%)
----------------------------------------------------------------------------------------------------------------------------

04eb.409e.a5c0  AP04EB.409E.07EC 3         0            0       99             0       63              0       0               
1880.90fd.6b40  paxxxxi-AP       2         0            0       0              0       0               NA      NA

show ap summary sort name

To view the access point (AP) summary sorted by name, use the show ap summary sort name command.

show ap summary sort name

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC(#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.7.1	This command was introduced.

Examples

This example shows how to view the AP summary sorted by name:


Device# show ap summary sort name 
Number of APs: 05
AP Name         Slots  AP Model          Ethernet MAC    Radio MAC       Location        Country  IP Address  State
-------------------------------------------------------------------------------------------------------------------------
ABC              2    AIR-AP1832I-D-K9   2c0b.e9b6.3618  2c0b.e9b7.3ec0  Real-AP-Testbed  IN      1.2.22.222  Registered
AP-Farm-1832I-4  2    AIR-AP1832I-D-K9   2c0b.e9b6.3e58  2c0b.e9b7.5fc0  Real-AP-Testbed  IN      1.2.22.22   Registered
AP-Farm-1832I-5  2    AIR-AP1832I-D-K9   2c0b.e9b6.3f60  2c0b.e9b7.63e0  Real-AP-Testbed  IN      1.2.22.22   Registered
AP-Farm-1832I-6  2    AIR-AP1832I-D-K9   2c0b.e9b6.3fe8  2c0b.e9b7.6600  Real-AP-Testbed  IN      1.2.22.22   Registered
AP-Farm-1832I-7  2    AIR-AP1832I-D-K9   2c0b.e9b6.4010  2c0b.e9b7.66a0  Real-AP-Testbed  IN      1.2.22.222

show ap summary sort ascending client-count

To view the AP summary sorted ascendingly based on the client count, use the show ap summary sort ascending client-count command.

show ap summary sort ascending client-count

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.1.1s	This command was introduced.

Examples

This example shows how to view the AP summary sorted ascendingly based on the client count:

Device# show ap summary sort ascending client-count
-----------------------------------------------------------------------------------------------------------------------------
AP-name                          AP-mac           Client count          Data Usage          Through-Put     Admin-State
-----------------------------------------------------------------------------------------------------------------------------
L2_3802I_1                       7872.5d27.b8c0       1                    622358               11            Enabled
L2_1815w_1                       707d.b99e.c2e0       2                    5871836              1422          Enabled

show ap summary sort ascending data-usage

To view the AP summary sorted ascendingly based on the data usage, use the show ap summary sort ascending data-usage command.

show ap summary sort ascending data-usage

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.1.1s	This command was introduced.

Examples

This example shows how to view the AP summary sorted ascendingly based on the data usage:

Device# show ap summary sort ascending data-usage
-----------------------------------------------------------------------------------------------------------------------------
AP-name                          AP-mac           Client count          Data Usage          Through-Put     Admin-State
-----------------------------------------------------------------------------------------------------------------------------
L2_3802I_1                       7872.5d27.b8c0       1                    622600               4             Enabled
L2_1815w_1                       707d.b99e.c2e0       2                    6102216              281           Enabled

show ap summary sort ascending throughput

To view the AP summary sorted ascendingly based on the throughput, use the show ap summary sort ascending throughput command.

show ap summary sort ascending throughput

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.1.1s	This command was introduced.

Examples

This example shows how to view the AP summary sorted ascendingly based on the throughput:

Device# show ap summary sort ascending throughput
-----------------------------------------------------------------------------------------------------------------------------
AP-name                          AP-mac           Client count          Data Usage          Through-Put     Admin-State
-----------------------------------------------------------------------------------------------------------------------------
L2_3802I_1                       7872.5d27.b8c0       1                    6749385              6             Enabled
L2_1815w_1                       707d.b99e.c2e0       2                    94748042             35            Enabled

show ap summary sort descending client-count

To view the AP summary sorted descendingly based on the client count, use the show ap summary sort descending client-count command.

show ap summary sort descending client-count

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.1.1s	This command was introduced.

Examples

This example shows how to view the AP summary sorted descendingly based on the client count:

Device# show ap summary sort descending client-count
-----------------------------------------------------------------------------------------------------------------------------
AP-name                          AP-mac           Client count          Data Usage          Through-Put     Admin-State
-----------------------------------------------------------------------------------------------------------------------------
L2_1815w_1                       707d.b99e.c2e0       2                    94753989             46            Enabled
L2_3802I_1                       7872.5d27.b8c0       1                    6750526              6             Enabled

show ap summary sort descending data-usage

To view the AP summary sorted descendingly based on the data usage, use the show ap summary sort descending data-usage command.

show ap summary sort descending data-usage

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.1.1s	This command was introduced.

Examples

This example shows how to view the AP summary sorted descendingly based on the data usage:

Device# show ap summary sort descending data-usage
-----------------------------------------------------------------------------------------------------------------------------
AP-name                          AP-mac           Client count          Data Usage          Through-Put     Admin-State
-----------------------------------------------------------------------------------------------------------------------------
L2_1815w_1                       707d.b99e.c2e0       2                    94756618             47            Enabled
L2_3802I_1                       7872.5d27.b8c0       0                    6750526              6             Enabled

show ap summary sort descending throughput

To view the AP summary sorted descendingly based on the throughput, use the show ap summary sort descending throughput command.

show ap summary sort descending throughput

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.1.1s	This command was introduced.

Examples

This example shows how to view the AP summary sorted descendingly based on the throughput:

Device# show ap summary sort descending throughput
-----------------------------------------------------------------------------------------------------------------------------
AP-name                          AP-mac           Client count          Data Usage          Through-Put     Admin-State
-----------------------------------------------------------------------------------------------------------------------------
L2_1815w_1                       707d.b99e.c2e0       2                    94758750             23            Enabled
L2_3802I_1                       7872.5d27.b8c0       0                    6750526              6             Enabled

show ap support-bundle summary

To display the summary of the AP support-bundle, use the show ap support-bundle summary command.

show ap support-bundle summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privilege EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.3.1	This command was introduced.

Examples

This examples displays the summary of the AP support-bundle:

Device# show ap support-bundle summary

show ap tag sources

To see AP tag sources with priorities, use the show ap tag sources command.

show ap tag sources [ chassis {chassis-number | active | standby} R0]

Syntax Description


`chassis-number`	Chassis number as either 1 or 2.
active R0	Active instance of the AP filters in Route-processor slot 0.
standby R0	Standby instance of the AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the AP tag sources with priorities for the active instance:

Device# show ap tag sources chassis active R0

show ap tag summary

To view brief summary of tag names, use the show ap tag summary command.

show ap tag summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following example shows how to view brief summary of tag names:

Device# show ap tag summary

show ap triradio summary

To view the tri-radio summary, and to verify if the slots are enabled and up, use the show ap triradio summary command.

show ap triradio summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privilege EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.2.1	This command was introduced.

Examples

This example displays the tri-radio summary, and to verify if the slots are enabled:

Device# show ap triradio summary

show ap timezone

To check the AP timezone information, use the show ap timezone command.

show ap timezone

Syntax Description


This command has no keywords and arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Examples

The following example shows how to check the AP timezone information:

Device# show ap timezone

AP Name   Status     Offsets(h/m) 
--------------------------------
AP1       Disabled    0:0
AP2       Enabled     1:0

show ap upgrade

To see AP upgrade information, use the show ap upgrade command.

show ap upgrade [name ap-upgrade-report-name | summary | chassis {chassis-number | active | standby}]

Syntax Description


name `ap-upgrade-report-name`	Enter the name of the AP upgrade report.
summary	Shows a summary of AP upgrade information.
`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance in Route-processor slot 0.
standby R0	Standby instance in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see a summary of the AP upgrade information:

Device# show ap upgrade summary

show ap upgrade method

To verify the status of the configuration of the image download over HTTPS method, use the show ap upgrade method command.

show ap upgrade method

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Dublin 17.11.1	This command was introduced.

Examples

The following example shows how to verify the status of HTTPS image download configuration:

Device# show ap upgrade method

AP upgrade method https : Enabled

show arp

To view the ARP table, use the show arp command.

show arp

Syntax Description


arp	Shows ARP table

Command Modes

User EXEC (>)

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows a sample output of the command:

Device# show arp

Address Age (min)     Hardware Addr
   9.11.8.1         0 84:80:2D:A0:D2:E6
9.11.32.111         0 3C:77:E6:02:33:3F

show arp summary

To see the ARP table summary, use the show arp summary command.

show arp summary

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the ARP table summary:

Device# show arp summary

show ap tunnel eogre events

To display the Ethernet over GRE (EoGRE) tunnel events, use the show ap tunnel eogre events command.

show ap tunnel eogre events

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to display the EoGRE tunnel events:

Device# show ap tunnel eogre events

AP 80e8.6fd4.9520  Event history
Timestamp               #Times   Event               RC Context
----------------------- -------- ------------------- -- ----------------------------------------
02/18/2019 23:50:26.341 6        IAPP_STATS           0 GW Tunnel2 uptime:0s                    
02/18/2019 23:49:40.222 2        CLIENT_JOIN          0 74da.3828.88b0, (eogre_domain/2121)     
02/18/2019 23:48:43.549 1        CLIENT_LEAVE         0 74da.3828.88b0, (eogre_domain/2121)     
02/18/2019 23:47:33.127 1        DOMAIN_STATUS        0 eogre_domain Active GW: Tunnel1         
02/18/2019 23:47:33.124 4        AP_TUNNEL_STATUS     0 Tunnel2 Dn                              
02/18/2019 23:47:33.124 1        MSG_CLIENT_DEL       0 GW Tunnel2 (IP: 9.51.1.12)              
02/18/2019 23:47:33.124 2        TUNNEL_ADD           0 GW Tunnel2                              
02/18/2019 23:47:33.120 3        MSG_CLIENT_DEL_PD    0 GW Tunnel1 (IP: 9.51.1.11)              
02/18/2019 23:47:31.763 2        AP_DOMAIN_PUSH       0 Delete:eogre_domain_set, 0 GWs          
02/18/2019 23:47:31.753 4        AP_VAP_PUSH          0 profile:'eogre_tunnel', wlan:pyats_eogre

show ap tunnel eogre domain detailed

To display the detailed information of the Ethernet over GRE (EoGRE) tunnel domain status on an AP, use the show ap tunnel eogre domain detailed command.

show ap tunnel eogre domain detailed domain-name

Syntax Description


`domain-name`	EoGRE domain name.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to display the detailed information of the EoGRE tunnel domain status:

Device# show ap tunnel eogre domain detailed Tunnel1


Gateway : Tunnel1
 Mode   : IPv4
 IP     : 9.51.1.11
 State  : Up
 MTU    : 1476
 Up Time: 14 hours 25 minutes 2 seconds 
 AP MAC : 80e8.6fd4.9520

 Clients
  Total Number of Wireless Clients      : 1
 Traffic
  Total Number of Received Packets      : 6
  Total Number of Received Bytes        : 2643
  Total Number of Transmitted Packets   : 94
  Total Number of Transmitted Bytes     : 20629
  Total Number of Lost Keepalive        : 3

show ap name tunnel eogre domain summary

To display the summary information of the Ethernet over GRE (EoGRE) tunnel domain on an AP, use the show ap nametunnel eogre domain summary command.

show ap name ap-name tunnel eogre domain summary

Syntax Description


`ap-name`	AP name.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to display the summary information of the EoGRE tunnel domain on an AP:

Device# show ap name ap1 tunnel eogre domain summary

AP MAC          Domain                           Active Gateway
-------------------------------------------------------------------------------
80e8.6fd4.9520  eogre_domain                     Tunnel1

show ap tunnel eogre gateway detailed

To display the detailed information of the Ethernet over GRE (EoGRE) tunnel gateway status on an AP, use the show ap name tunnel eogre gateway detailed command.

show ap name ap-name tunnel eogre gateway detailed gateway-name

Syntax Description


`ap-name`	AP name.
`gateway-name`	EoGRE domain name.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to display the detailed information of the EoGRE tunnel gateway status on an AP:

Device# show ap name ap1 tunnel eogre gateway detailed Tunnel1

Gateway : Tunnel1
 Mode   : IPv4
 IP     : 9.51.1.11
 State  : Up
 MTU    : 1476
 Up Time: 14 hours 25 minutes 2 seconds 
 AP MAC : 80e8.6fd4.9520

 Clients
  Total Number of Wireless Clients      : 1
 Traffic
  Total Number of Received Packets      : 6
  Total Number of Received Bytes        : 2643
  Total Number of Transmitted Packets   : 94
  Total Number of Transmitted Bytes     : 20629
  Total Number of Lost Keepalive        : 3

show ap tunnel eogre gateway summary

To display the summary information of the Ethernet over GRE (EoGRE) tunnel gateway, use the show ap tunnel eogre gateway summary command.

show ap tunnel eogre gateway summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to display the summary information of the EoGRE tunnel gateway:

Device# show ap tunnel eogre gateway summary

AP MAC          Gateway          Type  IP                                      State  Clients
---------------------------------------------------------------------------------------------
80e8.6fd4.9520  Tunnel1          IPv4  9.51.1.11                               Up     1     
80e8.6fd4.9520  Tunnel2          IPv4  9.51.1.12                               Down   0

show ap upgrade site

To view the upgrade site-related infromation, use the show ap upgrade site command.

show ap upgrade site [ summary ]

Syntax Description


summary	(Optional) Displays a summary of access point (AP) upgrade on individual sites.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.9.1	This command was introduced.

Examples

The following example shows how to view the upgrade site-related infromation:

Device# show ap upgrade site

Site-filtered AP upgrade report data
====================================
Source controller: Controller1
Destination controller: Controller2
Site-filters present: Yes
 
AP image upgrade site summary
-----------------------------
Operation: N+1 move
 
Site Tag                                  Status
---------------------------------------------------------
site1                                     In Progress
 
AP upgrade reports linked to these site-filters
-----------------------------------------------
 
Start time               Operation type             Report name
------------------------------------------------------------------------
01/30/2022 10:34:36 IST  AP image upgrade/move CLI  AP_upgrade_to_Controller2_3002022103435

show avc client

To display information about top number of applications, use the show avc client command in privileged EXEC mode.

show avc client client-mac top n application [ aggregate| upstream| downstream]

Syntax Description


client `client-mac`	Specifies the client MAC address.
top `n` application	Specifies the number of top "N" applications for the given client.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following is sample output from the show avc client command:

Device# sh avc client 0040.96ae.65ec top 10 application aggregate

Cumulative Stats:

No.  AppName      Packet-Count    Byte-Count       AvgPkt-Size     usage%
---------------------------------------------------------------------------
1    skinny          7343           449860           61             94
2    unknown         99             13631            137            3
3    dhcp            18             8752             486            2
4    http            18             3264             181            1
5    tftp            9              534              59             0
6    dns             2              224              112            0

Last Interval(90 seconds) Stats:

No.  AppName     Packet-Count     Byte-Count       AvgPkt-Size      usage%
----------------------------------------------------------------------------
1    skinny          9              540              60              100

show avc wlan

To display information about top applications and users using the applications, use the show avc wlan command in privileged EXEC mode.

show avc wlan ssid top n application [ aggregate| upstream| downstream]

Syntax Description


wlan `ssid`	Specifies the Service Set IDentifier (SSID) for WLAN.
top `n` application	Specifies the number of top "N" applications.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following is sample output from the show avc wlan command:

Device# show avc wlan Lobby_WLAN top 10 application aggregate

Cumulative Stats:

No.  AppName           Packet-Count          Byte-Count          AvgPkt-Size  usage%
--------------------------------------------------------------------------------------
1    ssl                10598677              1979525706            997          42
2    vnc                5550900               3764612847            678          14
3    http               3043131               2691327197            884          10
4    unknown            1856297               1140264956            614          4
5    video-over-http    1625019               2063335150            1269         8
6    binary-over-http   1329115               1744190344            1312         6
7    webex-meeting      1146872               540713787             471          2
8    rtp                923900                635650544             688          2
9    unknown            752341                911000213             1210         3
10   youtube            631085                706636186             1119         3

Last Interval(90 seconds) Stats:

No.  AppName          Packet-Count          Byte-Count            AvgPkt-Size  usage%
---------------------------------------------------------------------------------------
1    vnc                687093                602731844             877          68
2    video-over-http    213272                279831588             1312         31
3    ssl                6515                  5029365               771          1
4    webex-meeting      3649                  1722663               472          0
5    http               2634                  1334355               506          0
6    unknown            1436                  99412                 69           0
7    google-services    722                   378121                523          0
8    linkedin           655                   393263                600          0
9    exchange           432                   167390                387          0
10   gtalk-chat         330                   17330                 52           0

show awips wlc-alarm

To view the contents of the AWIPS WLC Alarm table, use the show awips wlc-alarm command.

show awips wlc-alarm

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.3.1	This command was introduced

Examples

The following example shows how to view the contents of the AWIPS WLC Alarm table:

Device# show awips wlc-alarm

Time                 BSSID           Client MAC      Alarm description        
------------------------------------------------------------
04/02/2020 16:03:18  e4aa.5d53.b921  74da.3864.2a94  WPA2 Key Reinstal KRACK  
04/02/2020 16:03:19  e4aa.5d53.b921  74da.3864.2a94  WPA2 Key Reinstal KRACK  
04/02/2020 16:03:20  e4aa.5d53.b921  74da.3864.2a94  WPA2 Key Reinstal KRACK  
04/02/2020 16:03:21  e4aa.5d53.b921  74da.3864.2a94  WPA2 Key Reinstal KRACK

show awips syslog throttle

To verify the syslog configuration for Cisco Advanced Wireless Intrusion Prevention System (aWIPS), use the show awips syslog throttle command.

show awips syslog throttle

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Examples

The following example shows how to verify the syslog configuration for aWIPS:

Device# show awips syslog throttle
Syslog Throttle Interval (seconds)                            
------------------------------------------------------------
60

show capwap client rcb

To view the CAPWAP status and modes, use the show capwap client rcb command on the access point.

show capwap client rcb

Syntax Description


This command has no keywords and arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.3.1	This command was introduced.

Examples

This example shows how to view the CAPWAP status and modes on the access point:

AP# show capwap client rcb 

OperationState                     : UP
Name                               : AP4001.7A39.2D5A
MwarHwVer                          : 0.0.0.0
Location                           : default location
ApMode                             : Remote Bridge
ApSubMode                          : Not Configured
CAPWAP Path MTU                    : 1485
Software Initiated Reload Reason   : Reload command
CAPWAP Sliding Window
Active Window Size                 : 10
Last Request Send To Application   : 184
Expected Seq Num                   : 185
Received Seq Num                   : 184
Request Packet Count               : 42424
Out Of Range Packets Count         : 0
Window Moved  Packets Count        : 0
In Range Packets Count             : 960
Expected Packets Count             : 41464

show chassis

To see the chassis information, use the show chassis command.

show chassis [1 | 2 | detail | mode | neighbors | ha-status {active | local | standby}]

Syntax Description


{`1` \| `2`}	Chassis number as 1 or 2 to see the information about the relevant chassis.
detail	Shows detailed information about the chassis.
mode	Shows information about the chassis mode.
neighbors	Shows information about the chassis neighbors.
ha-status	Option to see information about the High Availability (HA) status.
active	Shows HA status on the chassis that is in active state.
local	Shows HA status on the local chassis.
standby	Shows HA status on the chassis that is in standby state.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the HA status on the active chassis:

Device# show chassis ha-status active

show chassis rmi

To verify the chassis Redundancy Management Interface (RMI) configuration for an active controller, use the show chassis rmi command.

show chassis rmi

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.1.1	This command was introduced.

Examples

This example shows how to verify the chassis Redundancy Management Interface (RMI) configuration for an active controller:

Device# show chassis rmi
Chassis/Stack Mac Address : 000c.2964.1eb6 - Local Mac Address
Mac persistency wait time: Indefinite
H/W Current
Chassis# Role Mac Address Priority Version State IP RMI-IP
--------------------------------------------------------------------------------------------------------
*1 Active 000c.2964.1eb6 1 V02 Ready 169.254.90.147 9.10.90.147
2 Standby 000c.2975.3aa6 1 V02 Ready 169.254.90.149 9.10.90.149

show checkpoint

To display information about the Checkpoint Facility (CF) subsystem, use the show checkpoint command.

show checkpoint { clients client-ID <0-381>| entitiesentity-ID <1-7> | statistics buffer-usage}

Syntax Description


clients	Displays detailed information about checkpoint clients.
entities	Displays detailed information about checkpoint entities.
statistics	Displays detailed information about checkpoint statistics.
buffer-usage	Displays the checkpoint statistics of clients using large number of buffers.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to display all the CF clients.

   Client residing in process  : 8135
--------------------------------------------------------------------------------
Checkpoint client: WCM_MOBILITY
    Client ID                   : 24105
    Total DB inserts            : 0
    Total DB updates            : 0
    Total DB deletes            : 0
    Total DB reads              : 0
    Number of tables            : 6
    Client residing in process  : 8135
--------------------------------------------------------------------------------
Checkpoint client: WCM_DOT1X
    Client ID                   : 24106
    Total DB inserts            : 2
    Total DB updates            : 1312
    Total DB deletes            : 2
    Total DB reads              : 0
    Number of tables            : 1
    Client residing in process  : 8135
--------------------------------------------------------------------------------
Checkpoint client: WCM_APFROGUE
    Client ID                   : 24107
    Total DB inserts            : 0
    Total DB updates            : 0
    Total DB deletes            : 0
    Total DB reads              : 0
    Number of tables            : 1
    Client residing in process  : 8135
--------------------------------------------------------------------------------
Checkpoint client: WCM_CIDS
    Client ID                   : 24110
    Total DB inserts            : 0
    Total DB updates            : 0
    Total DB deletes            : 0
    Total DB reads              : 0
    Number of tables            : 0
    Client residing in process  : 8135
--------------------------------------------------------------------------------
Checkpoint client: WCM_NETFLOW
    Client ID                   : 24111
    Total DB inserts            : 7
    Total DB updates            : 0
    Total DB deletes            : 0
    Total DB reads              : 0
    Number of tables            : 1
    Client residing in process  : 8135
--------------------------------------------------------------------------------
Checkpoint client: WCM_MCAST
    Client ID                   : 24112
    Total DB inserts            : 0
    Total DB updates            : 0
    Total DB deletes            : 0
    Total DB reads              : 0
    Number of tables            : 1
    Client residing in process  : 8135
--------------------------------------------------------------------------------
Checkpoint client: wcm_comet
    Client ID                   : 24150
    Total DB inserts            : 0
    Total DB updates            : 0
    Total DB deletes            : 0
    Total DB reads              : 0
    Number of tables            : 0
    Client residing in process  : 8135
--------------------------------------------------------------------------------

All iosd checkpoint clients

--------------------------------------------------------------------------------
Client Name            Client     Entity     Bundle
                           ID         ID       Mode
--------------------------------------------------------------------------------
Network RF Client           3         --       Off

  Total API Messages Sent:                       0
  Total Transport Messages Sent:                 0
  Length of Sent Messages:                       0
  Total Blocked Messages Sent:                   0
  Length of Sent Blocked Messages:               0
  Total Non-blocked Messages Sent:               0
  Length of Sent Non-blocked Messages:           0
  Total Bytes Allocated:                         0
  Buffers Held:                                  0
  Buffers Held Peak:                             0
  Huge Buffers Requested:                        0
  Transport Frag Count:                          0
  Transport Frag Peak:                           0
  Transport Sends w/Flow Off:                    0
  Send Errs:                                     0
  Send Peer Errs:                                0
  Rcv Xform Errs:                                0
  Xmit Xform Errs:                               0
  Incompatible Messages:                         0
  Client Unbundles to Process Memory:            T
--------------------------------------------------------------------------------
Client Name            Client     Entity     Bundle
                           ID         ID       Mode
--------------------------------------------------------------------------------
SNMP CF Client             12         --       Off

  Total API Messages Sent:                       0
  Total Transport Messages Sent:                 0
  Length of Sent Messages:                       0
  Total Blocked Messages Sent:                   0
  Length of Sent Blocked Messages:               0
  Total Non-blocked Messages Sent:               0
  Length of Sent Non-blocked Messages:           0
  Total Bytes Allocated:                         0
  Buffers Held:                                  0
  Buffers Held Peak:                             0
  Huge Buffers Requested:                        0
  Transport Frag Count:                          0
  Transport Frag Peak:                           0
  Transport Sends w/Flow Off:                    0
  Send Errs:                                     0
  Send Peer Errs:                                0
  Rcv Xform Errs:                                0
  Xmit Xform Errs:                               0
  Incompatible Messages:                         0
  Client Unbundles to Process Memory:            T
--------------------------------------------------------------------------------
Client Name            Client     Entity     Bundle
                           ID         ID       Mode
--------------------------------------------------------------------------------
Online Diags HA            14         --       Off

  Total API Messages Sent:                       0
  Total Transport Messages Sent:                 0
  Length of Sent Messages:                       0
  Total Blocked Messages Sent:                   0
  Length of Sent Blocked Messages:               0
  Total Non-blocked Messages Sent:               0
  Length of Sent Non-blocked Messages:           0
  Total Bytes Allocated:                         0
  Buffers Held:                                  0
  Buffers Held Peak:                             0
  Huge Buffers Requested:                        0
  Transport Frag Count:                          0
  Transport Frag Peak:                           0
  Transport Sends w/Flow Off:                    0
  Send Errs:                                     0
  Send Peer Errs:                                0
  Rcv Xform Errs:                                0
  Xmit Xform Errs:                               0
  Incompatible Messages:                         0
  Client Unbundles to Process Memory:            T
--------------------------------------------------------------------------------
Client Name            Client     Entity     Bundle
                           ID         ID       Mode
--------------------------------------------------------------------------------
ARP                        22         --       Off

  Total API Messages Sent:                       0
  Total Transport Messages Sent:                 0
  Length of Sent Messages:                       0
  Total Blocked Messages Sent:                   0
  Length of Sent Blocked Messages:               0
  Total Non-blocked Messages Sent:               0
  Length of Sent Non-blocked Messages:           0
  Total Bytes Allocated:                         0
  Buffers Held:                                  0
  Buffers Held Peak:                             0
  Huge Buffers Requested:                        0
  Transport Frag Count:                          0
  Transport Frag Peak:                           0
  Transport Sends w/Flow Off:                    0
  Send Errs:                                     0
  Send Peer Errs:                                0
  Rcv Xform Errs:                                0
  Xmit Xform Errs:                               0
  Incompatible Messages:                         0
  Client Unbundles to Process Memory:            T
--------------------------------------------------------------------------------
Client Name            Client     Entity     Bundle
                           ID         ID       Mode
--------------------------------------------------------------------------------
Tableid CF                 27         --       Off

  Total API Messages Sent:                       0
  Total Transport Messages Sent:                 0
  Length of Sent Messages:                       0
  Total Blocked Messages Sent:                   0
  Length of Sent Blocked Messages:               0
  Total Non-blocked Messages Sent:               0
  Length of Sent Non-blocked Messages:           0
  Total Bytes Allocated:                         0
  Buffers Held:                                  0
  Buffers Held Peak:                             0
  Huge Buffers Requested:                        0
  Transport Frag Count:                          0
  Transport Frag Peak:                           0
  Transport Sends w/Flow Off:                    0
  Send Errs:                                     0
  Send Peer Errs:                                0
  Rcv Xform Errs:                                0
  Xmit Xform Errs:                               0
  Incompatible Messages:                         0
  Client Unbundles to Process Memory:            T
--------------------------------------------------------------------------------
Client Name            Client     Entity     Bundle
                           ID         ID       Mode
--------------------------------------------------------------------------------
Event Manager              33          0       Off

  Total API Messages Sent:                       0
  Total Transport Messages Sent:                --
  Length of Sent Messages:                       0
  Total Blocked Messages Sent:                   0
  Length of Sent Blocked Messages:               0
  Total Non-blocked Messages Sent:               0
  Length of Sent Non-blocked Messages:           0
  Total Bytes Allocated:                         0
  Buffers Held:                                  0
  Buffers Held Peak:                             0
  Huge Buffers Requested:                        0
  Transport Frag Count:                          0
  Transport Frag Peak:                           0
  Transport Sends w/Flow Off:                    0
  Send Errs:                                     0
  Send Peer Errs:                                0
  Rcv Xform Errs:                                0
  Xmit Xform Errs:                               0
  Incompatible Messages:                         0
  Client Unbundles to Process Memory:            T
--------------------------------------------------------------------------------
Client Name            Client     Entity     Bundle
                           ID         ID       Mode
--------------------------------------------------------------------------------
LAN-Switch Port Mana       35          0       Off

  Total API Messages Sent:                       0
  Total Transport Messages Sent:                --
  Length of Sent Messages:                       0
  Total Blocked Messages Sent:                   0
  Length of Sent Blocked Messages:               0
  Total Non-blocked Messages Sent:               0
  Length of Sent Non-blocked Messages:           0
  Total Bytes Allocated:                         0
  Buffers Held:                                  0
  Buffers Held Peak:                             0
  Huge Buffers Requested:                        0
  Transport Frag Count:                          0
  Transport Frag Peak:                           0
  Transport Sends w/Flow Off:                    0
  Send Errs:                                     0
  Send Peer Errs:                                0
  Rcv Xform Errs:                                0
  Xmit Xform Errs:                               0
  Incompatible Messages:                         0
  Client Unbundles to Process Memory:            T
--------------------------------------------------------------------------------
Client Name            Client     Entity     Bundle
                           ID         ID       Mode
--------------------------------------------------------------------------------
LAN-Switch PAgP/LACP       36          0       Off

  Total API Messages Sent:                       0
  Total Transport Messages Sent:                --
  Length of Sent Messages:                       0
  Total Blocked Messages Sent:                   0
  Length of Sent Blocked Messages:               0
  Total Non-blocked Messages Sent:               0
  Length of Sent Non-blocked Messages:           0
  Total Bytes Allocated:                         0
  Buffers Held:                                  0
  Buffers Held Peak:                             0
  Huge Buffers Requested:                        0
  Transport Frag Count:                          0
  Transport Frag Peak:                           0
  Transport Sends w/Flow Off:                    0
  Send Errs:                                     0
  Send Peer Errs:                                0
  Rcv Xform Errs:                                0
  Xmit Xform Errs:                               0
  Incompatible Messages:                         0
  Client Unbundles to Process Memory:            T
--------------------------------------------------------------------------------
Client Name            Client     Entity     Bundle
                           ID         ID       Mode
--------------------------------------------------------------------------------
LAN-Switch VLANs           39          0       Off

  Total API Messages Sent:                       0
  Total Transport Messages Sent:                --
  Length of Sent Messages:                       0
  Total Blocked Messages Sent:                   0
  Length of Sent Blocked Messages:               0
  Total Non-blocked Messages Sent:               0
  Length of Sent Non-blocked Messages:           0
  Total Bytes Allocated:                         0
  Buffers Held:                                  0
  Buffers Held Peak:                             0
  Huge Buffers Requested:                        0
  Transport Frag Count:                          0
  Transport Frag Peak:                           0
  Transport Sends w/Flow Off:                    0
  Send Errs:                                     0
  Send Peer Errs:                                0
  Rcv Xform Errs:                                0

This example shows how to display all the CF entities.

KATANA_DOC#show checkpoint entities
                         Check Point List of Entities

 CHKPT on ACTIVE server.

--------------------------------------------------------------------------------
Entity ID         Entity Name
--------------------------------------------------------------------------------
        0         CHKPT_DEFAULT_ENTITY

  Total API Messages Sent:             0
  Total Messages Sent:                 0
  Total Sent Message Len:              0
  Total Bytes Allocated:               0
  Total Number of Members:            10

  Member(s) of entity 0 are:
    Client ID          Client Name
------------------------------------------
          168          DHCP Snooping
          167          IGMP Snooping
           41          Spanning-tree
           40          AUTH MGR CHKPT CLIEN
           39          LAN-Switch VLANs
           33          Event Manager
           35          LAN-Switch Port Mana
           36          LAN-Switch PAgP/LACP
          158          Inline Power Checkpoint

This example shows how to display the CF statistics.

KATANA_DOC#show checkpoint statistics
        IOSd Check Point Status
 CHKPT on ACTIVE server.

Number Of Msgs In Hold Q:              0
CHKPT MAX Message Size:                0
TP MAX Message Size:               65503
CHKPT Pending Msg Timer:             100 ms

  FLOW_ON  total:                      0
  FLOW_OFF total:                      0
  Current FLOW status is:             ON
  Total API Messages Sent:             0
  Total Messages Sent:                 0
  Total Sent Message Len:              0
  Total Bytes Allocated:               0
  Rcv  Msg Q Peak:                     0
  Hold Msg Q Peak:                     0
  Buffers Held Peak:                   0
  Current Buffers Held:                0
  Huge Buffers Requested:              0

show cts environment data

To display the TrustSec environment data on the AP, use the show cts environment data command:

show cts environment data

Syntax Description


This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco Amsterdam 17.1.1	This command was introduced.

Examples

The following example shows the TrustSec environment data on the AP:

Device# show cts environment

CTS Environment Data
====================
Current state = COMPLETE
Last status   = Successful
Local Device SGT:
SGT tag = 0-07:Unknown
Server List Info:
Installed list: CTSServerList1-0001, 1 server(s):
Server: 8.109.0.85, port 1812, A-ID 9818EE1ECA02B7BFE359C28B30EA7E2A
Status = ALIVE
auto-test = FALSE, keywrap-enable = FALSE, idle-time = 60 mins, deadtime = 20 secs
Security Group Name Table:
0-07:Unknown
2-00:TrustSec_Devices
3-00:Network_Services
4-00:Employees
5-00:Contractors
6-00:Guests
7-00:Production_Users
8-00:Developers
9-00:Auditors
10-00:Point_of_Sale_Systems
11-02:Production_Servers
12-00:Development_Servers
13-00:Test_Servers
14-00:PCI_Servers
15-00:BYOD
16-06:BGL15
17-00:BGL12
255-00:Quarantined_Systems
Environment Data Lifetime = 86400 secs
Last update time = 11:50:49 UTC Sun Jan 9 2022
Env-data expires in   0:00:28:54 (dd:hr:mm:sec)
Env-data refreshes in 0:00:28:54 (dd:hr:mm:sec)
Cache data applied = NONE
State Machine is running

show cts role-based sgt-map all

To display the bindings of IP address and SGT source names on the AP, use the show cts role-based sgt-map all command:

show cts role-based sgt-map all

Syntax Description


This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco Amsterdam 17.1.1	This command was introduced.

Examples

The following example shows the bindings of IP address and SGT source names on the AP:

Device# show cts role-based stg-map all

Active IPv4-SGT Bindings Information
IP Address                                 SGT       Source
==========================================================================
8.73.1.101                                  16      LOCAL
8.73.1.102                                  16      LOCAL
8.73.1.103                                  16      LOCAL
8.73.1.104                                  16      LOCAL
8.73.1.105                                  16      LOCAL
8.73.1.106                                  16      LOCAL
8.73.1.107                                  16      LOCAL
8.73.1.108                                  16      LOCAL
8.73.1.109                                  16      LOCAL
8.73.1.110                                  16      LOCAL
8.73.1.111                                  16      LOCAL
8.73.1.112                                  16      LOCAL
8.73.1.113                                  16      LOCAL
8.73.1.114                                  16      LOCAL
8.73.1.115                                  16      LOCAL
8.73.1.116                                  16      LOCAL
8.73.1.117                                  16      LOCAL
8.73.1.118                                  16      LOCAL
8.73.1.119                                  16      LOCAL
8.73.1.120                                  16      LOCAL
8.73.1.121                                  16      LOCAL
8.73.1.122                                  16      LOCAL
8.73.1.123                                  16      LOCAL
8.73.1.124                                  16      LOCAL
8.73.1.125                                  16      LOCAL
8.73.1.126                                  16      LOCAL
8.73.1.127                                  16      LOCAL
8.73.1.128                                  16      LOCAL
8.73.1.129                                  16      LOCAL
8.73.1.130                                  16      LOCAL
8.73.1.131                                  16      LOCAL
8.73.1.132                                  16      LOCAL
8.73.1.133                                  16      LOCAL
8.73.1.134                                  16      LOCAL
8.73.1.135                                  16      LOCAL
8.73.1.136                                  16      LOCAL
8.73.1.137                                  16      LOCAL
8.73.1.138                                  16      LOCAL
8.73.1.139                                  16      LOCAL
8.73.1.140                                  16      LOCAL
8.73.1.141                                  16      LOCAL
8.73.1.142                                  16      LOCAL
FD09:8::                                    16      LOCAL
FD09:8:73:0:4051:EB27:B4A2:F6DB             16      LOCAL
FD09:8:73:0:4C3C:1D75:81E0:DB94             16      LOCAL
FD09:8:73:0:5136:9045:9D11:E191             16      LOCAL
FD09:8:73:0:6903:B84E:5BDF:9D54             16      LOCAL
FD09:8:73:0:A9F8:7825:B07:75A8              16      LOCAL
FD09:8:73:0:B505:626B:51D7:6DB6             16      LOCAL
FD09:8:73:0:D0B4:3316:7CE9:8AE8             16      LOCAL
FD09:8:73:0:ECA8:F5E:CCF5:FFD7              16      LOCAL

IP-SGT Active Bindings Summary
============================================
Total number of LOCAL    bindings = 9
Total number of active   bindings = 9

show cts role-based counters

To clear all role-based counters on the AP, use the show cts role-based counters command:

show cts role-based counters

Syntax Description


This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco Amsterdam 17.1.1	This command was introduced.

Examples

The following example shows the clear all role-based counters on the AP:

Device# show cts role-based counters

From  To   SW-Denied HW-Denied SW-Permitt HW-Permitt  SW-Monitor HW-Monitor
===========================================================================
*     *     0          0          0          178837189  0           0
16    0     0          0          0          39250482   0           0
16    16    0          52835      0          0          0           0
17    16    0          0          0          0          0           0

show environment summary

To view a summary of all the environment-monitoring sensors, use the show environment summary command.

show environment summary

Syntax Description


This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.
Cisco IOS XE Bengaluru 17.5.1	This command output was modified.

Example

The following is a sample output of the show environment summary command:

Examples

Device# show environment summary


Number of Critical alarms:  0
Number of Major alarms:     0
Number of Minor alarms:     0

 Slot        Sensor          Current State   Reading        Threshold(Minor,Major,Critical,Shutdown)
 ----------  --------------  --------------- ------------   ---------------------------------------
 P0          Vin             Normal          231  V AC   	na
 P0          Iin             Normal          2    A      	na
 P0          Vout            Normal          12   V DC   	na
 P0          Iout            Normal          30   A      	na
 P0          Temp1           Normal          25   Celsius	(na ,na ,na ,na )(Celsius)
 P0          Temp2           Normal          31   Celsius	(na ,na ,na ,na )(Celsius)
 P0          Temp3           Normal          37   Celsius	(na ,na ,na ,na )(Celsius)
 R0          VDMB1: VX1      Normal          1226 mV     	na
 R0          VDMB1: VX2      Normal          6944 mV     	na
 R0          VDMB1: VX3      Normal          1226 mV     	na
 R0          VDMB1: VX4      Normal          1000 mV     	na
 R0          VDMB1: VP1      Normal          1789 mV     	na
 R0          VDMB1: VP2      Normal          2555 mV     	na
 R0          VDMB1: VP3      Normal          2556 mV     	na
 R0          VDMB1: VP4      Normal          1049 mV     	na
 R0          VDMB1: VH       Normal          11993mV     	na
 R0          VDMB2: VX2      Normal          4975 mV     	na
 R0          VDMB2: VX3      Normal          853  mV     	na
 R0          VDMB2: VX4      Normal          907  mV     	na
 R0          VDMB2: VX5      Normal          1008 mV     	na
 R0          VDMB2: VP1      Normal          1787 mV     	na
 R0          VDMB2: VP2      Normal          3323 mV     	na
 R0          VDMB2: VH       Normal          12003mV     	na
 R0          VDMB3: VX1      Normal          968  mV     	na
 R0          VDMB3: VX2      Normal          1002 mV     	na
 R0          VDMB3: VX5      Normal          5090 mV     	na
 R0          VDMB3: VP1      Normal          2492 mV     	na
 R0          VDMB3: VP2      Normal          1196 mV     	na
 R0          VDMB3: VP3      Normal          1512 mV     	na
 R0          VDMB3: VP4      Normal          1509 mV     	na
 R0          VDMB3: VH       Normal          11998mV     	na
 R0          Temp: DMB IN    Normal          26   Celsius	(45 ,55 ,65 ,70 )(Celsius)
 R0          Temp: DMB OUT   Normal          40   Celsius	(70 ,75 ,80 ,85 )(Celsius)
 R0          Temp: Yoda 0    Normal          54   Celsius	(95 ,105,110,115)(Celsius)
 R0          Temp: Yoda 1    Normal          62   Celsius	(95 ,105,110,115)(Celsius)
 R0          Temp: CPU Die   Normal          43   Celsius	(100,110,120,125)(Celsius)
 R0          Temp: FC FANS   Fan Speed 70%   26   Celsius	(29 ,39 ,0  )(Celsius)
 R0          VDDC1: VX1      Normal          1005 mV     	na
 R0          VDDC1: VX2      Normal          7084 mV     	na
 R0          VDDC1: VX3      Normal          950  mV     	na
 R0          VDDC1: VP1      Normal          1800 mV     	na
 R0          VDDC1: VP2      Normal          2493 mV     	na
 R0          VDDC1: VP3      Normal          3325 mV     	na
 R0          VDDC1: VH       Normal          12019mV     	na
 R0          VDDC2: VX2      Normal          751  mV     	na
 R0          VDDC2: VX3      Normal          749  mV     	na
 R0          VDDC2: VX5      Normal          5076 mV     	na
 R0          VDDC2: VP1      Normal          1009 mV     	na
 R0          VDDC2: VP2      Normal          1008 mV     	na
 R0          VDDC2: VP3      Normal          1197 mV     	na
 R0          VDDC2: VP4      Normal          1514 mV     	na
 R0          VDDC2: VH       Normal          12003mV     	na
 R0          Temp: DDC IN    Normal          25   Celsius	(55 ,65 ,75 ,80 )(Celsius)
 R0          Temp: DDC OUT   Normal          35   Celsius	(75 ,85 ,95 ,100)(Celsius)
 P0          Stby Vin        Normal          230  V AC   	na
 P0          Stby Iin        Normal          2    A      	na
 P0          Stby Vout       Normal          12   V DC   	na
 P0          Stby Iout       Normal          32   A      	na
 P0          Stby Temp1      Normal          24   Celsius	(na ,na ,na ,na )(Celsius)
 P0          Stby Temp2      Normal          29   Celsius	(na ,na ,na ,na )(Celsius)
 P0          Stby Temp3      Normal          35   Celsius	(na ,na ,na ,na )(Celsius)
 R0          Stby VDMB1: VX1 Normal          1225 mV     	na
 R0          Stby VDMB1: VX2 Normal          6979 mV     	na
 R0          Stby VDMB1: VX3 Normal          1226 mV     	na
 R0          Stby VDMB1: VX4 Normal          999  mV     	na
 R0          Stby VDMB1: VP1 Normal          1791 mV     	na
 R0          Stby VDMB1: VP2 Normal          2560 mV     	na
 R0          Stby VDMB1: VP3 Normal          2558 mV     	na
 R0          Stby VDMB1: VP4 Normal          1050 mV     	na
 R0          Stby VDMB1: VH  Normal          11977mV     	na
 R0          Stby VDMB2: VX2 Normal          5005 mV     	na
 R0          Stby VDMB2: VX3 Normal          854  mV     	na
 R0          Stby VDMB2: VX4 Normal          878  mV     	na
 R0          Stby VDMB2: VX5 Normal          1008 mV     	na
 R0          Stby VDMB2: VP1 Normal          1789 mV     	na
 R0          Stby VDMB2: VP2 Normal          3312 mV     	na
 R0          Stby VDMB2: VH  Normal          11977mV     	na
 R0          Stby VDMB3: VX1 Normal          972  mV     	na
 R0          Stby VDMB3: VX2 Normal          1001 mV     	na
 R0          Stby VDMB3: VX5 Normal          5060 mV     	na
 R0          Stby VDMB3: VP1 Normal          2497 mV     	na
 R0          Stby VDMB3: VP2 Normal          1199 mV     	na
 R0          Stby VDMB3: VP3 Normal          1510 mV     	na
 R0          Stby VDMB3: VP4 Normal          1511 mV     	na
 R0          Stby VDMB3: VH  Normal          11982mV     	na
 R0          Stby Temp: DMB INormal          22   Celsius	(45 ,55 ,65 ,70 )(Celsius)
 R0          Stby Temp: DMB ONormal          32   Celsius	(70 ,75 ,80 ,85 )(Celsius)
 R0          Stby Temp: Yoda Normal          43   Celsius	(95 ,105,110,115)(Celsius)
 R0          Stby Temp: Yoda Normal          45   Celsius	(95 ,105,110,115)(Celsius)
 R0          Stby Temp: CPU DNormal          33   Celsius	(100,110,120,125)(Celsius)
 R0          Stby Temp: FC FAFan Speed 70%   22   Celsius	(29 ,39 ,0  )(Celsius)
 R0          Stby VDDC1: VX1 Normal          1005 mV     	na
 R0          Stby VDDC1: VX2 Normal          7070 mV     	na
 R0          Stby VDDC1: VX3 Normal          949  mV     	na
 R0          Stby VDDC1: VP1 Normal          1814 mV     	na
 R0          Stby VDDC1: VP2 Normal          2501 mV     	na
 R0          Stby VDDC1: VP3 Normal          3331 mV     	na
 R0          Stby VDDC1: VH  Normal          11993mV     	na
 R0          Stby VDDC2: VX2 Normal          752  mV     	na
 R0          Stby VDDC2: VX3 Normal          750  mV     	na
 R0          Stby VDDC2: VX5 Normal          5052 mV     	na
 R0          Stby VDDC2: VP1 Normal          1009 mV     	na
 R0          Stby VDDC2: VP2 Normal          994  mV     	na
 R0          Stby VDDC2: VP3 Normal          1195 mV     	na
 R0          Stby VDDC2: VP4 Normal          1514 mV     	na
 R0          Stby VDDC2: VH  Normal          11993mV     	na
 R0          Stby Temp: DDC INormal          22   Celsius	(55 ,65 ,75 ,80 )(Celsius)
 R0          Stby Temp: DDC ONormal          28   Celsius	(75 ,85 ,95 ,100)(Celsius)

show etherchannel summary

To show details on the ports, port-channel, and protocols in the controller, use the show etherchannel summary command.

show ethernet summary

This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged Mode.

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows the details on the ports, port-channel, and protocols in the controller.

controller#show etherchannel summary
Flags:  D - down        P - bundled in port-channel
        I - stand-alone s - suspended
        H - Hot-standby (LACP only)
        R - Layer3      S - Layer2
        U - in use      f - failed to allocate aggregator

        M - not in use, minimum links not met
        u - unsuitable for bundling
        w - waiting to be aggregated
        d - default port


Number of channel-groups in use: 2
Number of aggregators:           2

Group  Port-channel  Protocol    Ports
------+-------------+-----------+-----------------------------------------------
2      Po2(SD)          -
23     Po23(SD)         -

show fips authorization-key

To view the installed authorization key, use the show fips authorization-key command.

show fips authorization-key

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.12.1	This command was introduced.

Examples

This example shows how to view the installed authorization key:


Device# show fips authorization-key
FIPS: Stored key (16) : 12345678901234567890123456789012

show fips status

To view the status of FIPS on the device, use the show fips status command.

show fips status

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.12.1	This command was introduced.

Examples

This example shows how to view the status of FIPS on the device:


Device# show fips status
Chassis is running in fips mode

show flexconnect office-extend diagnostics

To display the results of the network diagnostics for all flexconnect OfficeExtend AP, use the show flexconnect office-extend diagnostics command.

show flexconnect office-extend diagnostics

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.5.1	This command was introduced.

Usage Guidelines

To get periodic details for latency (current, minimum, or maximum) ensure that you enable link-latency under the ap profile, as given in the following example:

Device(config)# ap profile default-ap-profile
Device(config-ap-profile)# link-latency

If the above configuration is not in place, you will only see the following output:

Summary of OfficeExtend AP Link Latency

CAPWAP Latency Heartbeat

Current: current latency (ms)
Min: minimum latency (ms)
Max: maximum latency (ms)

Link Test

Upload: DTLS Upload (Mbps)
Latency: DTLS Link Latency (ms)
Jitter: DTLS Link Jitter (ms)

AP Name Last Latency Heartbeat from AP Current Max Min Last Link Test Run Upload Latency Jitter 
----------------------------------------------------------------------------------------------------------------------------------------
ap-18   Disabled                        -       -   -  12/04/20 11:08:58   16     3       0

Examples

This following example shows how to display the network diagnostics information for OfficeExtend AP.

Device# show flexconnect office-extend diagnostics

Summary of OfficeExtend AP Link Latency

CAPWAP Latency Heartbeat

Current: current latency (ms)
Min: minimum latency (ms)
Max: maximum latency (ms)

Link Test

Upload: DTLS Upload (Mbps)
Latency: DTLS Link Latency (ms)
Jitter: DTLS Link Jitter (ms)

AP Name Last Latency Heartbeat from AP Current Max Min Last Link Test Run Upload Latency Jitter
-----------------------------------------------------------------------------------------------
ap-18    1 minute 1 second             0        0   0  12/04/20 09:19:48  8       2       0

show flow exporter

To display flow exporter status and statistics, use the show flow exporter command in privileged EXEC mode.

show flow exporter [export-ids netflow-v9 | [name] exporter-name [statistics | templates] | statistics | templates]

Syntax Description


export-ids netflow-v9	(Optional) Displays the NetFlow Version 9 export fields that can be exported and their IDs.
name	(Optional) Specifies the name of a flow exporter.
`exporter-name`	(Optional) Name of a flow exporter that was previously configured.
statistics	(Optional) Displays statistics for all flow exporters or for the specified flow exporter.
templates	(Optional) Displays template information for all flow exporters or for the specified flow exporter.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following example displays the status and statistics for all of the flow exporters configured on a device:

Device# show flow exporter
Flow Exporter FLOW-EXPORTER-1:
  Description:              Exports to the datacenter
  Export protocol:          NetFlow Version 9
  Transport Configuration:
    Destination IP address: 192.168.0.1
    Source IP address:      192.168.0.2
    Transport Protocol:     UDP
    Destination Port:       9995
    Source Port:            55864
    DSCP:                   0x0
    TTL:                    255
    Output Features:        Used

This table describes the significant fields shown in the display:

Table 1. show flow exporter Field Descriptions
Field	Description
Flow Exporter	The name of the flow exporter that you configured.
Description	The description that you configured for the exporter, or the default description User defined.
Transport Configuration	The transport configuration fields for this exporter.
Destination IP address	The IP address of the destination host.
Source IP address	The source IP address used by the exported packets.
Transport Protocol	The transport layer protocol used by the exported packets.
Destination Port	The destination UDP port to which the exported packets are sent.
Source Port	The source UDP port from which the exported packets are sent.
DSCP	The differentiated services code point (DSCP) value.
TTL	The time-to-live value.
Output Features	Specifies whether the output-features command, which causes the output features to be run on Flexible NetFlow export packets, has been used or not.

The following example displays the status and statistics for all of the flow exporters configured on a device:

Device# show flow exporter name FLOW-EXPORTER-1 statistics
Flow Exporter FLOW-EXPORTER-1:
  Packet send statistics (last cleared 2w6d ago):
    Successfully sent:         0                     (0 bytes)

show flow interface

To display the configuration and status for an interface, use the show flow interface command in privileged EXEC mode.

show flow interface [type number]

Syntax Description


`type`	(Optional) The type of interface on which you want to display accounting configuration information.
`number`	(Optional) The number of the interface on which you want to display accounting configuration information.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following example displays the accounting configuration on Ethernet interfaces 0/0 and 0/1:

Device# show flow interface gigabitethernet1/0/1

Interface Ethernet1/0
        monitor:         FLOW-MONITOR-1
        direction:       Output
        traffic(ip):     on
Device# show flow interface gigabitethernet1/0/2
Interface Ethernet0/0
        monitor:         FLOW-MONITOR-1
        direction:       Input
        traffic(ip):     sampler SAMPLER-2#

The table below describes the significant fields shown in the display.

Table 2. show flow interface Field Descriptions
Field	Description
Interface	The interface to which the information applies.
monitor	The name of the flow monitor that is configured on the interface.
direction:	The direction of traffic that is being monitored by the flow monitor. The possible values are: Input—Traffic is being received by the interface. Output—Traffic is being transmitted by the interface.
traffic(ip)	Indicates if the flow monitor is in normal mode or sampler mode. The possible values are: on—The flow monitor is in normal mode. sampler—The flow monitor is in sampler mode (the name of the sampler will be included in the display).

show flow monitor

To display the status and statistics for a flow monitor, use the show flow monitor command in privileged EXEC mode.

Syntax Description


name	(Optional) Specifies the name of a flow monitor.
`monitor-name`	(Optional) Name of a flow monitor that was previously configured.
cache	(Optional) Displays the contents of the cache for the flow monitor.
format	(Optional) Specifies the use of one of the format options for formatting the display output.
csv	(Optional) Displays the flow monitor cache contents in comma-separated variables (CSV) format.
record	(Optional) Displays the flow monitor cache contents in record format.
table	(Optional) Displays the flow monitor cache contents in table format.
statistics	(Optional) Displays the statistics for the flow monitor.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

The cache keyword uses the record format by default.

The uppercase field names in the display output of the show flowmonitor monitor-name cache command are key fields that uses to differentiate flows. The lowercase field names in the display output of the show flow monitor monitor-name cache command are nonkey fields from which collects values as additional data for the cache.

Examples

The following example displays the status for a flow monitor:

Device# show flow monitor FLOW-MONITOR-1
 
Flow Monitor FLOW-MONITOR-1:
  Description:       Used for basic traffic analysis
  Flow Record:       flow-record-1
  Flow Exporter:     flow-exporter-1
                     flow-exporter-2
  Cache:
    Type:              normal
    Status:            allocated
    Size:              4096 entries / 311316 bytes
    Inactive Timeout:  15 secs
    Active Timeout:    1800 secs

This table describes the significant fields shown in the display.

Table 3. show flow monitor monitor-name Field Descriptions
Field	Description
Flow Monitor	Name of the flow monitor that you configured.
Description	Description that you configured or the monitor, or the default description User defined.
Flow Record	Flow record assigned to the flow monitor.
Flow Exporter	Exporters that are assigned to the flow monitor.
Cache	Information about the cache for the flow monitor.
Type	Flow monitor cache type. The value is always normal, as it is the only supported cache type.
Status	Status of the flow monitor cache. The possible values are: allocated—The cache is allocated. being deleted—The cache is being deleted. not allocated—The cache is not allocated.
Size	Current cache size.
Inactive Timeout	Current value for the inactive timeout in seconds.
Active Timeout	Current value for the active timeout in seconds.

The following example displays the status, statistics, and data for the flow monitor named FLOW-MONITOR-1:

This table describes the significant fields shown in the display.

The following example displays the status, statistics, and data for the flow monitor named FLOW-MONITOR-1 in a table format:

The following example displays the status, statistics, and data for the flow monitor named FLOW-MONITOR-IPv6 (the cache contains IPv6 data) in record format:

The following example displays the status and statistics for a flow monitor:

show flow record

To display the status and statistics for a flow record, use the show flow record command in privileged EXEC mode.

show flow record [ [name] record-name]

Syntax Description


name	(Optional) Specifies the name of a flow record.
`record-name`	(Optional) Name of a user-defined flow record that was previously configured.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following example displays the status and statistics for FLOW-RECORD-1:

Device# show flow record FLOW-RECORD-1
flow record FLOW-RECORD-1:
  Description:        User defined
  No. of users:       0
  Total field space:  24 bytes
  Fields:
    match ipv6 destination address
    match transport source-port
    collect interface input

show flow record wireless avc basic

To view information about the flow records for wireless avc basic, use the show flow record wireless avc basic command.

show flow record wireless avc basic

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following example shows how to see information about the flow records for wireless avc basic:

Device# show flow record wireless avc basic 

flow record wireless avc basic:
  Description:        Basic Wireless AVC template
  No. of users:       1
  Total field space:  78 bytes
  Fields:
    match ipv4 protocol
    match ipv4 source address
    match ipv4 destination address
    match transport source-port
    match transport destination-port
    match flow direction
    match application name
    match wireless ssid
    collect counter bytes long
    collect counter packets long
    collect wireless ap mac address
    collect wireless client mac address

show flow record wireless avc ipv6 basic

To view information about the flow records for wireless avc ipv6 basic, use the show flow record wireless avc ipv6 basic command.

show flow record wireless avc ipv6 basic

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following example shows how to see information about the flow records for wireless avc ipv6 basic:

Device# show flow record wireless avc ipv6 basic 

flow record wireless avc ipv6 basic:
  Description:        Ipv6 Wireless AVC flow template
  No. of users:       1
  Total field space:  102 bytes
  Fields:
    match ipv6 protocol
    match ipv6 source address
    match ipv6 destination address
    match transport source-port
    match transport destination-port
    match flow direction
    match wireless ssid
    collect counter bytes long
    collect counter packets long
    collect application name
    collect wireless ap mac address
    collect wireless client mac address

show gnxi state

To verify the gnxi details, use the show gnxi state command.

show gnxi state

Syntax Description


detail	Displays the gnxi detailed state.
stats	Displays the gnxi operational statistics.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Examples

The following example shows how to verify the gnxi details:

Device# show gnxi state detail
Settings
========
Server: Enabled
Server port: 50052
Secure server: Disabled
Secure server port: 5000
Secure client authentication: Enabled
Secure trustpoint: test
Secure client trustpoint:
Secure password authentication: Disabled

GNMI
====
Admin state: Enabled
Oper status: Up
State: Provisioned

gRPC Server
-----------
Admin state: Enabled
Oper status: Up

Configuration service
---------------------
Admin state: Enabled
Oper status: Up

Telemetry service
-----------------
Admin state: Enabled
Oper status: Up

GNOI
====

Cert Management service
-----------------
Admin state: Enabled
Oper status: Up

OS Image service
----------------
Admin state: Disabled
Oper status: Up
Supported: Not supported on this platform

show history channel interface dot11Radio all

To check channel change or trigger reason and history, use the show history channel interface dot11Radio all command.

show history channel interface dot11Radio all

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.2.1	This command was introduced.

Examples

This example shows how to check channel change or trigger reason and history:

Device# show history channel interface dot11Radio all

               Timestamp Slot Client count Channel Trigger
Fri May 31 12:57:04 2019    0            0      11 RRM-DCA
Fri May 31 13:10:02 2019    0            0       1 RRM-DCA
Fri May 31 12:57:04 2019    1            0      60  Manual
Fri May 31 13:00:16 2019    1            0     149     DFS

show interfaces

To display the administrative and operational status of all interfaces or for a specified interface, use the show interfaces command in privileged EXEC mode.

Syntax Description

interface-id

(Optional) ID of the interface. Valid interfaces include physical ports (including type, stack member , module, and port number) and port channels. The port channel range is 1 to 48.

vlan vlan-id

(Optional) VLAN identification. The range is 1 to 4094.

accounting

(Optional) Displays accounting information on the interface, including active protocols and input and output packets and octets.

Note

The display shows only packets processed in software; hardware-switched packets do not appear.

capabilities

(Optional) Displays the capabilities of all interfaces or the specified interface, including the features and options that you can configure on the interface. Though visible in the command line help, this option is not available for VLAN IDs.

module number

(Optional) Displays capabilities of all interfaces on the switch or specified stack member.

This option is not available if you entered a specific interface ID.

description

(Optional) Displays the administrative status and description set for an interface.

etherchannel

(Optional) Displays interface EtherChannel information.

flowcontrol

(Optional) Displays interface flow control information.

private-vlan mapping

(Optional) Displays private-VLAN mapping information for the VLAN switch virtual interfaces (SVIs). This keyword is not available if the switch is running the LAN base feature set.

pruning

(Optional) Displays trunk VTP pruning information for the interface.

stats

(Optional) Displays the input and output packets by switching the path for the interface.

status

(Optional) Displays the status of the interface. A status of unsupported in the Type field means that a non-Cisco small form-factor pluggable (SFP) module is inserted in the module slot.

err-disabled

(Optional) Displays interfaces in an error-disabled state.

trunk

(Optional) Displays interface trunk information. If you do not specify an interface, only information for active trunking ports appears.

Note

Though visible in the command-line help strings, the crb , fair-queue , irb , mac-accounting , precedence , random-detect , rate-limit , and shape keywords are not supported.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

The show interfaces capabilities command with different keywords has these results:

Use the show interface capabilities module number command to display the capabilities of all interfaces on that chassis in the stack. If there is no chassis with that module number in the stack, there is no output.
Use the show interfaces interface-id capabilities to display the capabilities of the specified interface.
Use the show interfaces capabilities (with no module number or interface ID) to display the capabilities of all interfaces in the stack.

Examples

This is an example of output from the show interfaces command for an interface on stack member 3:

Device# show interfaces gigabitethernet3/0/2
GigabitEthernet3/0/2 is down, line protocol is down (notconnect)
  Hardware is Gigabit Ethernet, address is 2037.064d.4381 (bia 2037.064d.4381)
  MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Auto-duplex, Auto-speed, media type is 10/100/1000BaseTX
  input flow-control is off, output flow-control is unsupported
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input never, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts (0 multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 0 multicast, 0 pause input
     0 input packets with dribble condition detected
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 unknown protocol drops
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 pause output
     0 output buffer failures, 0 output buffers swapped out

This is an example of output from the show interfaces interface description command when the interface has been described as Connects to Marketing by using the description interface configuration command:

Device# show interfaces gigabitethernet1/0/2 description
Interface                      Status         Protocol Description
Gi1/0/2                        up             down     Connects to Marketing

This is an example of output from the show interfaces interface-id pruning command when pruning is enabled in the VTP domain:

Device# show interfaces gigabitethernet1/0/2 pruning
Port 				 Vlans pruned for lack of request by neighbor
Gi1/0/2   3,4

Port 			  Vlans traffic requested of neighbor
Gi1/0/2   1-3

This is an example of output from the show interfaces stats command for a specified VLAN interface:

Device# show interfaces vlan 1 stats
Switching path    Pkts In    Chars In    Pkts Out    Chars Out
     Processor    1165354   136205310      570800     91731594
   Route cache          0           0           0            0
         Total    1165354   136205310      570800     91731594

These are examples of output from the show interfaces status command for a specific interface when private VLANs are configured. Port 22 is configured as a private-VLAN host port. It is associated with primary VLAN 20 and secondary VLAN 25:

Device# show interfaces gigabitethernet1/0/22 status
Port 						Name 					Status 					Vlan 					Duplex 					Speed					 Type
Gi1/0/22 												connected 		20,25 				a-full 					a-100 					10/100BaseTX

In this example, port 20 is configured as a private-VLAN promiscuous port. The display shows only the primary VLAN 20:

Device# show interfaces gigabitethernet1/0/20 status
Port 						Name 					Status 					Vlan 					Duplex 					Speed					 Type
Gi1/0/20 												connected 		20    				a-full 					a-100 					10/100BaseTX

This is an example of output from the show interfaces status err-disabled command. It displays the status of interfaces in the error-disabled state:

Device# show interfaces status err-disabled
Port 		   Name       Status         Reason
Gi1/0/2              err-disabled   gbic-invalid
Gi2/0/3              err-disabled   dtp-flap

This is an example of output from the show interfaces interface-id pruning command:

Device# show interfaces gigabitethernet1/0/2 pruning
Port Vlans pruned for lack of request by neighbor

Device# show interfaces gigabitethernet1/0/1 trunk
Port        Mode             Encapsulation  Status        Native vlan
Gi1/0/1     on               802.1q         other         10

Port        Vlans allowed on trunk
Gi1/0/1     none

Port        Vlans allowed and active in management domain
Gi1/0/1     none

Port        Vlans in spanning tree forwarding state and not pruned
Gi1/0/1     none

show interfaces dot11Radio asr-info

To view advanced scheduling request statistics along with advanced scheduling request capability and uplink latency statistics for advanced scheduling request clients on a WLAN, use the show interfaces dot11Radio asr-info command.

show interfaces dot11Radio asr-info radio-interface-number { all | mac-address }

Syntax Description


`radio-interface-number`	Interface number for 802.11 radio.
all	Displays advanced scheduling request statistics along with advanced scheduling request capability and uplink latency statistics for all the advanced scheduling request clients on a WLAN.
`mac-address`	MAC address of the AP.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.4.1	This command was introduced

Examples

The following example shows how to view advanced scheduling request statistics along with advanced scheduling request capability and uplink latency statistics for all the advanced scheduling request clients on a WLAN:

Device# show interfaces dot11Radio 1 asr-info all

[*10/12/2020 18:45:21.0149] 
[*10/12/2020 18:45:21.0150]  Client-MAC:[26:52:CF:C8:D0:1C] AID:[3] ASR-Capability:[0x1]
[*10/12/2020 18:45:21.0150]  BE- LAT[0-20]:[267] LAT[20-40]:[57] LAT[40-100]:[32] LAT[>100]:[26]
[*10/12/2020 18:45:21.0150]  BK- LAT[0-20]:[0] LAT[20-40]:[0] LAT[40-100]:[0] LAT[>100]:[0]
[*10/12/2020 18:45:21.0150]  VI- LAT[0-20]:[0] LAT[20-40]:[0] LAT[40-100]:[0] LAT[>100]:[0]
[*10/12/2020 18:45:21.0150]  VO- LAT[0-20]:[2222] LAT[20-40]:[409] LAT[40-100]:[224] LAT[>100]:[163]
[*10/12/2020 18:45:21.0150]  
[*10/12/2020 18:45:21.0206] HTT_PEER_DETAILS_TLV:
[*10/12/2020 18:45:21.0206] peer_type = 0
[*10/12/2020 18:45:21.0206] sw_peer_id = 98
[*10/12/2020 18:45:21.0206] vdev_id = 25
[*10/12/2020 18:45:21.0206] pdev_id = 0
[*10/12/2020 18:45:21.0206] ast_idx = 1187
[*10/12/2020 18:45:21.0206] mac_addr = 26:52:cf:c8:d0:1c
[*10/12/2020 18:45:21.0206] peer_flags = 0x200006f9
[*10/12/2020 18:45:21.0206] qpeer_flags = 0x8
[*10/12/2020 18:45:21.0206] 
[*10/12/2020 18:45:21.0206] HTT_STATS_PEER_ASR_STATS_TLV
[*10/12/2020 18:45:21.0206] asr_bmap: 0x8
[*10/12/2020 18:45:21.0206] asr_muedca_update_cnt: 1
[*10/12/2020 18:45:21.0206] asr_muedca_reset_cnt: 1
[*10/12/2020 18:45:21.0206] asr_ul_mu_bsr_trigger: 2376
[*10/12/2020 18:45:21.0206] asr_min_trig_intv- BE:0         BK:0 VI:0 VO:19
[*10/12/2020 18:45:21.0206] asr_max_trig_intv- BE:0         BK:0 VI:0 VO:20
[*10/12/2020 18:45:21.0207] asr_min_alloc_rate- BE:0         BK:0 VI:0 VO:12
[*10/12/2020 18:45:21.0207] asr_ul_su_data_ppdu_cnt- BE:0         BK:0 VI:0 VO:2149
[*10/12/2020 18:45:21.0207] asr_ul_su_data_ppdu_bytes- BE:0         BK:0 VI:0 VO:757546
[*10/12/2020 18:45:21.0207] asr_ul_mu_trig_ppdu_cnt- BE:0         BK:0 VI:0 VO:5002
[*10/12/2020 18:45:21.0207] asr_ul_mu_trig_ppdu_bytes- BE:0         BK:0 VI:0 VO:2400960
[*10/12/2020 18:45:21.0207] asr_ul_mu_data_ppdu_cnt- BE:0         BK:0 VI:0 VO:2134
[*10/12/2020 18:45:21.0207] asr_ul_mu_data_ppdu_bytes- BE:0         BK:0 VI:0 VO:736578
[*10/12/2020 18:45:21.0207] asr_ul_mu_data_padding_bytes- BE:0         BK:0 VI:0 VO:2953488

show interfaces wired

To view the wired interface details, use the show interfaces wired command.

show interfaces wired wired-interface-number

Syntax Description


`wired-interface-number`	Wired interface number.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.2.1	This command was introduced.

Examples

This example shows how to view the wired interface details:

Device# show interfaces wired 0

wired0    Link encap:Ethernet  HWaddr C8:8B:5E:BA:D0 eMac Status: UP
          inet addr:20.200.51.14  Bcast:20.255.255.255  Mask:255.255.255.255
          UP BROADCAST RUNNING PROMISC MULTICAST  MTU:2400  Metric:1
          full Duplex, 1000 Mb/s

Wired0 Port Statistics:
ID         :               2             TYPE       :               0
RX PKTS    :           35109/431         TX PKTS    :            1307/11
RX OCTETS  :         2899435/34925       TX OCTETS  :          377424/1575
RX ERR     :             287/0           TX ERR     :               0/0

show inventory

To display the product inventory listing of all Cisco products installed in the networking device, use the show inventory command.

show inventory [ entity-name | [ fru | oid | raw ] entity-name ]

Syntax Description


`entity-name`	(Optional) Name of a Cisco entity (for example, chassis, backplane, module, or slot). A quoted string may be used to display very specific UDI information; for example "sfslot 1" shows the UDI information for slot 1 of an entity named sfslot.
fru	(Optional) To display the component details of the fru entities within the container hierarchy in Cisco products.
oid	(Optional) To display the vendor specific hardware registration number for each part of the device.
raw	(Optional) To view the information about all Cisco products—referred to as entities—installed in the Cisco networking device, even if the entities do not have a product ID (PID) value, a unique device identifier (UDI), or other physical identification.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Usage Guidelines

The show inventory command retrieves and displays inventory information about each Cisco product in the form of a UDI. The UDI is a combination of three separate data elements: a product identifier (PID), a version identifier (VID), and the serial number (SN).

The PID is the name by which the product can be ordered; it has been historically called the "Product Name" or "Part Number." This is the identifier that one would use to order an exact replacement part.

The VID is the version of the product. Whenever a product has been revised, the VID will be incremented. The VID is incremented according to a rigorous process derived from Telcordia GR-209-CORE, an industry guideline that governs product change notices.

The SN is the vendor-unique serialization of the product. Each manufactured product will carry a unique serial number assigned at the factory, which cannot be changed in the field. This is the means by which to identify an individual, specific instance of a product.

The UDI refers to each product as an entity. Some entities, such as a chassis, will have subentities like slots. Each entity will display on a separate line in a logically ordered presentation that is arranged hierarchically by Cisco entities.

Use the show inventory command without options to display a list of Cisco entities installed in the networking device that are assigned a PID.

Examples

This example shows how to display the product inventory listing of a Cisco product installed in the networking device:

Device# show inventory

NAME: "module R0", DESCR: "Cisco C9800-CL Route Processor"
PID: C9800-CL-K9       , VID: V00  , SN: Jxx1xxxxx1x

show ip

To view the IP information, use the show ip command.

Syntax Description


access-lists	Lists the IP access lists
interface	Displays the IP interface status and configuration
brief	Displays the brief summary of IP status and configuration
route	Displays the IP routing table
tunnel	Displays the IP tunnel information
eogre	Displays the EoGRE tunnel information
domain	Displays the EoGRE tunnel domain information
forwarding-table	Displays the EoGRE tunnel encapsulation and decapsulation information
gateway	Displays the EoGRE tunnel gateway information
fabric	Displays the IP fabric tunnel information
summary	Displays the information for all tunnels

Command Modes

User EXEC (>)

Privileged EXEC (#)

Command History


Release	Modification
8.1.111.0	This command was introduced.

Examples

The following example shows how to view information about the lists the IP access lists:

cisco-wave2-ap# show ip access-lists

show ip igmp snooping igmpv2-tracking

To display group and IP address entries, use the show ip igmp snooping igmpv2-tracking command in privileged EXEC mode.

Note

The command displays group and IP address entries only for wireless multicast IGMP joins and not for wired joins. This command also displays output only if wireless multicast is enabled.

show ip igmp snooping igmpv2-tracking

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

show ip igmp snooping querier

To display the configuration and operation information for the IGMP querier that is configured on a device, use the show ip igmp snooping querier command in user EXEC mode.

show ip igmp snooping querier [ vlan vlan-id] [ detail ]

Syntax Description


vlan `vlan-id`	(Optional) Specifies a VLAN; Ranges are from 1―1001 and 1006―4094.
detail	(Optional) Displays detailed IGMP querier information.

Command Modes

User EXEC

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

Use the show ip igmp snooping querier command to display the IGMP version and the IP address of a detected device, also called a querier, that sends IGMP query messages. A subnet can have multiple multicast routers but only one IGMP querier. In a subnet running IGMPv2, one of the multicast routers is elected as the querier. The querier can be a Layer 3 device.

The show ip igmp snooping querier command output also shows the VLAN and the interface on which the querier was detected. If the querier is the device, the output shows the Port field as Router. If the querier is a router, the output shows the port number on which the querier was detected in the Port field.

The show ip igmp snooping querier detail user EXEC command is similar to the show ip igmp snooping querier command. However, the show ip igmp snooping querier command displays only the device IP address most recently detected by the device querier.

The show ip igmp snooping querier detail command displays the device IP address most recently detected by the device querier and this additional information:

The elected IGMP querier in the VLAN
The configuration and operational information pertaining to the device querier (if any) that is configured in the VLAN

Expressions are case sensitive, for example, if you enter | exclude output , the lines that contain "output" do not appear, but the lines that contain "Output" appear.

Examples

The following is a sample output from the show ip igmp snooping querier command:

Device> show ip igmp snooping querier
Vlan      IP Address     IGMP Version        Port
---------------------------------------------------
1         172.20.50.11   v3                  Gi1/0/1
2         172.20.40.20   v2                  Router

The following is a sample output from the show ip igmp snooping querier detail command:

Device> show ip igmp snooping querier detail

Vlan      IP Address     IGMP Version   Port
-------------------------------------------------------------
1         10.0.0.10      v2             Fa8/0/1 
Global IGMP device querier status

--------------------------------------------------------
admin state                    : Enabled
admin version                  : 2
source IP address              : 0.0.0.0        
query-interval (sec)           : 60
max-response-time (sec)        : 10
querier-timeout (sec)          : 120
tcn query count                : 2
tcn query interval (sec)       : 10
Vlan 1:   IGMP device querier status
--------------------------------------------------------
elected querier is 10.0.0.10         on port Fa8/0/1
--------------------------------------------------------
admin state                    : Enabled
admin version                  : 2
source IP address              : 10.1.1.65      
query-interval (sec)           : 60
max-response-time (sec)        : 10
querier-timeout (sec)          : 120
tcn query count                : 2
tcn query interval (sec)       : 10
operational state              : Non-Querier
operational version            : 2
tcn query pending count        : 0

show ip igmp snooping wireless mcast-spi-count

To display the statistics of the number of multicast stateful packet inspections (SPIs) per multicast group ID (MGID) sent to the device, use the show ip igmp snooping wireless mcast-spi-count command in privileged EXEC mode.

show ip igmp snooping wireless mcast-spi-count

This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

None

Examples

This is an example of output from the show ip igmp snooping wireless mcast-spi-count command:

Device# show ip igmp snooping wireless mcast-spi-count

Stats for Mcast Client Add/Delete SPI Messages Sent to WCM

MGID    ADD MSGs        Del MSGs
---------------------------------
4160    1323            667

show ip igmp snooping wireless mgid

To display multicast group ID (MGID) mappings, use the show ip igmp snooping wireless mgid command in privileged EXEC mode.

show ip igmp snooping wireless mgid

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

None

Examples

This is an example of output from the show ip igmp snooping wireless mgid command:

Device# show ip igmp snooping wireless mgid

Total number of L2-MGIDs    = 0

Total number of MCAST MGIDs = 0

 Wireless multicast is Enabled in the system
 Vlan     bcast   nonip-mcast   mcast    mgid    Stdby Flags
 1     Disabled   Disabled   Enabled    Disabled  0:0:1:0
 25    Disabled   Disabled   Enabled    Disabled  0:0:1:0
 34    Disabled   Disabled   Enabled    Disabled  0:0:1:0
 200   Disabled   Disabled   Enabled    Disabled  0:0:1:0
 1002  Enabled    Enabled    Enabled    Disabled  0:0:1:0
 1003  Enabled    Enabled    Enabled    Disabled  0:0:1:0
 1004  Enabled    Enabled    Enabled    Disabled  0:0:1:0
 1005  Enabled    Enabled    Enabled    Disabled  0:0:1:0

Index  MGID                  (S, G, V)
--------------------------------------------------------

show ip nbar protocol-discovery wlan

To see NBAR protocol discovery statistics for a WLAN, use the show ip nbar protocol-discovery wlan command.

show ip nbar protocol-discovery wlan wlan-name

Syntax Description


`wlan-name`	Name of the WLAN.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the NBAR protocol discovery statistics for a WLAN named mywlan:

Device# show ip nbar protocol-discovery wlan mywlan

show ipv6 access-list

To display the contents of all current IPv6 access lists, use the show ipv6 access-list command in user EXEC or privileged EXEC mode.

show ipv6 access-list [access-list-name]

Syntax Description


`access-list-name`	(Optional) Name of access list.

Command Default

All IPv6 access lists are displayed.

Command Modes

User EXEC

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

The show ipv6 access-list command provides output similar to the show ip access-list command, except that it is IPv6-specific.

Examples

The following output from the show ipv6 access-list command shows IPv6 access lists named inbound, tcptraffic, and outbound:


Device# show ipv6 access-list
IPv6 access list inbound
    permit tcp any any eq bgp reflect tcptraffic (8 matches) sequence 10
    permit tcp any any eq telnet reflect tcptraffic (15 matches) sequence 20
    permit udp any any reflect udptraffic sequence 30
IPv6 access list tcptraffic (reflexive) (per-user)
    permit tcp host 2001:0DB8:1::1 eq bgp host 2001:0DB8:1::2 eq 11000 timeout 300 (time         left 243) sequence 1
    permit tcp host 2001:0DB8:1::1 eq telnet host 2001:0DB8:1::2 eq 11001 timeout 300         (time left 296) sequence 2
IPv6 access list outbound
    evaluate udptraffic
    evaluate tcptraffic

The following sample output shows IPv6 access list information for use with IPSec:


Device#  show ipv6 access-list
IPv6 access list Tunnel0-head-0-ACL (crypto)
     permit ipv6 any any (34 matches) sequence 1
IPv6 access list Ethernet2/0-ipsecv6-ACL (crypto)
     permit 89 FE80::/10 any (85 matches) sequence 1

The table below describes the significant fields shown in the display.

Table 4. show ipv6 access-list Field Descriptions
Field	Description
ipv6 access list inbound	Name of the IPv6 access list, for example, inbound.
permit	Permits any packet that matches the specified protocol type.
tcp	Transmission Control Protocol. The higher-level (Layer 4) protocol type that the packet must match.
any	Equal to ::/0.
eq	An equal operand that compares the source or destination ports of TCP or UDP packets.
bgp	Border Gateway Protocol. The lower-level (Layer 3) protocol type that the packet must be equal to.
reflect	Indicates a reflexive IPv6 access list.
tcptraffic (8 matches)	The name of the reflexive IPv6 access list and the number of matches for the access list. The clear ipv6 access-list privileged EXEC command resets the IPv6 access list match counters.
sequence 10	Sequence in which an incoming packet is compared to lines in an access list. Lines in an access list are ordered from first priority (lowest number, for example, 10) to last priority (highest number, for example, 80).
host 2001:0DB8:1::1	The source IPv6 host address that the source address of the packet must match.
host 2001:0DB8:1::2	The destination IPv6 host address that the destination address of the packet must match.
11000	The ephemeral source port number for the outgoing connection.
timeout 300	The total interval of idle time (in seconds) after which the temporary IPv6 reflexive access list named tcptraffic will time out for the indicated session.
(time left 243)	The amount of idle time (in seconds) remaining before the temporary IPv6 reflexive access list named tcptraffic is deleted for the indicated session. Additional received traffic that matches the indicated session resets this value to 300 seconds.
evaluate udptraffic	Indicates the IPv6 reflexive access list named udptraffic is nested in the IPv6 access list named outbound.

show ipv6 hop-by-hop status

To display information about IPv6 hop-by-hop header processing, use the show ipv6 hop-by-hop status command.

show ipv6 hop-by-hop status

Syntax Description


This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Examples

The following example displays information about IPv6 hop-by-hop header processing:

Device# show ipv6 hop-by-hop status

show ipv6 mld snooping

Use the show ipv6 mld snooping command in EXEC mode to display IP version 6 (IPv6) Multicast Listener Discovery (MLD) snooping configuration of the switch or the VLAN.

show ipv6 mld snooping [vlan vlan-id]

Syntax Description


vlan `vlan-id`	(Optional) Specify a VLAN; the range is 1 to 1001 and 1006 to 4094.

Command Modes

User EXEC

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

Use this command to display MLD snooping configuration for the switch or for a specific VLAN.

VLAN numbers 1002 through 1005 are reserved for Token Ring and FDDI VLANs and cannot be used in MLD snooping.

To configure the dual IPv4 and IPv6 template, enter the sdm prefer dual-ipv4-and-ipv6 global configuration command and reload the switch.

Examples

This is an example of output from the show ipv6 mld snooping vlan command. It shows snooping characteristics for a specific VLAN.


Device# show ipv6 mld snooping vlan 100
Global MLD Snooping configuration:
-------------------------------------------
MLD snooping : Enabled
MLDv2 snooping (minimal) : Enabled
Listener message suppression : Enabled
TCN solicit query : Disabled
TCN flood query count : 2
Robustness variable : 3
Last listener query count : 2
Last listener query interval : 1000
Vlan 100:
--------
MLD snooping : Disabled
MLDv1 immediate leave : Disabled
Explicit host tracking : Enabled
Multicast router learning mode : pim-dvmrp
Robustness variable : 3
Last listener query count : 2
Last listener query interval : 1000

This is an example of output from the show ipv6 mld snooping command. It displays snooping characteristics for all VLANs on the switch.


Device# show ipv6 mld snooping 
Global MLD Snooping configuration:
-------------------------------------------
MLD snooping : Enabled
MLDv2 snooping (minimal) : Enabled
Listener message suppression : Enabled
TCN solicit query : Disabled
TCN flood query count : 2
Robustness variable : 3
Last listener query count : 2
Last listener query interval : 1000
 
Vlan 1:
--------
MLD snooping : Disabled
MLDv1 immediate leave : Disabled
Explicit host tracking : Enabled
Multicast router learning mode : pim-dvmrp
Robustness variable : 1
Last listener query count : 2
Last listener query interval : 1000
 
<output truncated>
 
Vlan 951:
--------
MLD snooping : Disabled
MLDv1 immediate leave : Disabled
Explicit host tracking : Enabled
Multicast router learning mode : pim-dvmrp
Robustness variable : 3
Last listener query count : 2
Last listener query interval : 1000

show ipv6 mld snooping querier vlan

To see IPv6 MLD querier information in a VLAN, use the show ipv6 mld snooping querier vlan command.

show ipv6 mld snooping querier vlan vlan-id

Syntax Description


`vlan-id`	VLAN ID. Valid range is 1 to 1001 and 1006 to 4094.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the IPv6 MLD querier information in a VLAN whose ID is 3:

Device# show ipv6 mld snooping querier vlan 3

show ipv6 mld snooping wireless mgid

To see multicast group identifer (MGID) mapping information in the IPv6 MLD wireless related snooping events, use the show ipv6 mld snooping wireless mgid command.

show ipv6 mld snooping wireless mgid

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see multicast group identifer (MGID) mapping information in the IPv6 MLD wireless related snooping events:

Device# show ipv6 mld snooping wireless mgid

show ipv6 nd ra specific-route

To display information about IPv6 neighbor discovery router advertisement messages, use the show ipv6 nd ra specific-route command.

show ipv6 nd ra specific-route interface

Syntax Description


`interface`	Interface information.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Usage Guidelines

If you do not specify the interface, routes configured under all the interfaces are displayed.

Examples

The following example displays information about IPv6 neighbor discovery router advertisement messages:

Device# show ipv6 nd ra specific-route

show ldap attributes

To view information about the default LDAP attribute mapping, use the show ldap attributes command.

show ldap attributes

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view information about the default LDAP attribute mapping:

Device# show ldap attributes
LDAP Attribute                     Format     AAA Attribute
==============                     ======     =============
airespaceBwDataBurstContract       Ulong      bsn-data-bandwidth-burst-contr
userPassword                       String     password
airespaceBwRealBurstContract       Ulong      bsn-realtime-bandwidth-burst-c
employeeType                       String     employee-type
airespaceServiceType               Ulong      service-type
airespaceACLName                   String     bsn-acl-name
priv-lvl                           Ulong      priv-lvl
memberOf                           String DN  supplicant-group
cn                                 String     username
airespaceDSCP                      Ulong      bsn-dscp
policyTag                          String     tag-name
airespaceQOSLevel                  Ulong      bsn-qos-level
airespace8021PType                 Ulong      bsn-8021p-type
airespaceBwRealAveContract         Ulong      bsn-realtime-bandwidth-average
airespaceVlanInterfaceName         String     bsn-vlan-interface-name
airespaceVapId                     Ulong      bsn-wlan-id
airespaceBwDataAveContract         Ulong      bsn-data-bandwidth-average-con
sAMAccountName                     String     sam-account-name
meetingContactInfo                 String     contact-info
telephoneNumber                    String     telephone-number
Map: att_map_1
department                         String DN  element-req-qos

show ldap server

To view the LDAP server information, use the show ldap server command.

show ldap server { server-name | all }

Syntax Description


`server-name`	Name of the server.
all	Information of all the servers.

Command Default

None

Command Modes

Privileged EXEC(#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the LDAP server information:

Device# show ldap server all

show license air entities

To display information about active APs, new APs, and deleted APs in connection with a Cisco Catalyst Wireless Controller, enter the show license air entities command in privileged EXEC mode.

show license air entities { added | bulk | deleted | no-change | summary }

Syntax Description


added	Displays the list of newly reported APs. A newly added AP is one that was not listed in the last RUM report that the product instance generated.
bulk	Displays the list of all currently active APs for the product instance
deleted	Displays the list of deleted APs. A delete AP is one that was listed as active APs in the last RUM report that the product instance generated but is now disconnected.
no-change	Displays the list of APs where there has been no change in the status since the last report.
summary	Displays the RUM report generation particulars and information about active APs, new APs, and deleted APs, and indicates by when an acknowledgement (ACK) must be installed on the product instance.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.
Cisco IOS XE Amsterdam 17.3.2a	Command output was updated to display information relating to Smart Licensing Using Policy.
Cisco IOS XE Cupertino 17.7.1	The output of the show license air entities summary command was enhanced to display the following new field only on a Cisco Catalyst 9800-CL Wireless Controller: `License Ack expected within`

Usage Guidelines

Smart Licensing: If the software version on the device is Cisco IOS XE Amsterdam 17.3.1 or an earlier release, command output displays fields pertinent to Smart Licensing.

Smart Licensing Using Policy: If the software version on the device is Cisco IOS XE Amsterdam 17.3.2 or a later release, command output displays fields pertinent to Smart Licensing Using Policy.

Examples

For information about fields shown in the display for the show license air entities summary command, see Table 1 .

For sample output, see

Table 5. show license air entities summary Field Descriptions

Field

Description

Last license report time

When the last RUM report was generated, in the local time zone.

Upcoming license report time

When the next RUM report will be generated, in the local time zone.

No. of APs active at last report

Total number of APs listed as active APs in the last RUM report that was generated.

No. of APs newly added with last report

Number of new APs in the last RUM report that was generated.

For example, if the number displayed here is 2, this means the last but one RUM report did not list these 2 APs, and are therefore newly added in the last RUM report that the product instance generated.

No. of APs deleted with last report

Total number of APs deleted as of the last RUM report that was generated.

For example, if the number displayed here is 2, this means 2 APs were in the last but one RUM report, but were deleted in the last RUM report was generated.

License Ack expected within

Note

This field is displayed only on a Cisco Catalyst 9800-CL Wireless Controller running Cisco IOS XE Cupertino 17.7.1 or a later release.

If the field is displayed, it means you must complete RUM reporting and ensure that the ACK is made available on the product instance - at least once.

show license air entities summary on a Cisco Catalyst 9800-CL Wireless Controller

This example shows how to identify when an ACK is required on a Cisco Catalyst 9800-CL Wireless Controller

Beginning with Cisco IOS XE Cupertino 17.7.1, if you are using a Cisco Catalyst 9800-CL Wireless Controller, you must complete RUM reporting and ensure that the ACK is made available on the product instance - at least once. This is to ensure that correct and up-to-date usage information is reflected in CSSM.

Prior to 17.7.1, reporting and ACK installation was not mandatory for a Cisco Catalyst 9800-CL Wireless Controller.

The following is sample output on a Cisco Catalyst 9800-CL Wireless Controller, where an ACK must be made available on the product instance within 179 days. If this deadline is not met, currently active APs are not disconnected, but no new AP joins are allowed after the ACK deadline is passed. System messages are also displayed daily, until the first ACK is installed.

Device# show license air entities summary 
Upcoming license report time....................: 21:05:16.092 UTC Mon Oct 25 2021
No. of APs active at last report................: 57
No. of APs newly added with last report.........: 57
No. of APs deleted with last report.............: 0
License Ack expected within.....................: 179 days

Detailed information about this requirement is available in the configuration guide. In the Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, version Cisco IOS XE Cupertino 17.7.1 onwards, see the System Configuration → Smart Licensing Using Policy → RUM Reporting and Acknowledgment Requirement for Cisco Catalyst 9800-CL Wireless Controller.

show license air entities summary on a Cisco Catalyst 9800-L Wireless Controller

The following is sample output on a Cisco Catalyst 9800-L Wireless Controller. Note how the output on this device does not display the License Ack expected within field. Reporting requirements on all Cisco Catalyst Wireless Controllers (except Cisco Catalyst 9800-CL Wireless Controller) are as per the standard guidelines in the Smart Licensing Using Policy environment: Reporting is required if the policy (show license status ) or system messages indicate that it is.

Device# show license air entities summary 
Upcoming license report time....................: 15:13:27.403 IST Tue Oct 26 2021
No. of APs active at last report................: 1
No. of APs newly added with last report.........: 1
No. of APs deleted with last report.............: 0

show license all

To display all licensing information enter the show license all command in Privileged EXEC mode. This command displays status, authorization, UDI, and usage information, all combined.

show license all

Syntax Description


This command has no keywords or arguments

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.
Cisco IOS XE Amsterdam 17.3.2a	Command output was updated to display information relating to Smart Licensing Using Policy. Command output no longer displays Smart Account and Virtual account information.
Cisco IOS XE Cupertino 17.7.1	The output of the command was enhanced to display the following information: RUM report statistics, in section `Usage Report Summary`. Smart Account and Virtual Account information, in section `Account Information`.

Usage Guidelines

Smart Licensing: If the software version on the device is Cisco IOS XE Amsterdam 17.3.1 or an earlier release, command output displays fields pertinent to Smart Licensing.

Smart Licensing Using Policy: If the software version on the device (also referred to as a product instance) is Cisco IOS XE Amsterdam 17.3.2 or a later release, command output displays fields pertinent to Smart Licensing Using Policy.

This command concatenates the output of other show license commands, enabling you to display different kinds of licensing information together. For field descriptions, refer to the corresponding commands in the links provided below.

The Smart Licensing Status and Account Information sections of the show license all command corresponds with the output of the show license status command.

The License Usage section of the show license all command corresponds with the output of the show license usage command.

The Product Information section of the show license all command corresponds with the output of the show license udi command.

The Agent Version section of the show license all command displays the Smart Agent version and is available only in this command.

The License Authorizations section of the show license all command corresponds with the output of the show license authorization command.

The Usage Report Summary section of the show license all command corresponds with the output in the show license tech command.

Examples

For sample output, see:

Example: show license all (Cisco Catalyst 9800-CL Wireless Controllers, 17.7.1)

Example: show license all (Cisco Catalyst 9800-CL Wireless Controllers)

Examples

The following is sample output of the show license all command, on a product instance where the software version is Cisco IOS XE Cupertino 17.7.1. Note the addition of the two new sections in this release: Account Information and Usage Report Summary:

Device# show license all

Smart Licensing Status
======================

Smart Licensing is ENABLED

Export Authorization Key:
  Features Authorized:
    <none>

Utility:
  Status: DISABLED

Smart Licensing Using Policy:
  Status: ENABLED

Account Information:
  Smart Account: Eg-SA
  Virtual Account: Eg-VA

Data Privacy:
  Sending Hostname: yes
    Callhome hostname privacy: DISABLED
    Smart Licensing hostname privacy: DISABLED
  Version privacy: DISABLED
          
Transport:
  Type: Smart
  URL: https://smartreceiver.cisco.com/licservice/license
  Proxy:  
    Not Configured
  VRF:    
    Not Configured
          
Miscellaneous:
  Custom Id: <empty>
          
Policy:   
  Policy in use: Merged from multiple sources.
  Reporting ACK required: yes (CISCO default)
  Unenforced/Non-Export Perpetual Attributes:
    First report requirement (days): 365 (CISCO default)
    Reporting frequency (days): 0 (CISCO default)
    Report on change (days): 90 (CISCO default)
  Unenforced/Non-Export Subscription Attributes:
    First report requirement (days): 90 (CISCO default)
    Reporting frequency (days): 90 (CISCO default)
    Report on change (days): 90 (CISCO default)
  Enforced (Perpetual/Subscription) License Attributes:
    First report requirement (days): 0 (CISCO default)
    Reporting frequency (days): 0 (CISCO default)
    Report on change (days): 0 (CISCO default)
  Export (Perpetual/Subscription) License Attributes:
    First report requirement (days): 0 (CISCO default)
    Reporting frequency (days): 0 (CISCO default)
    Report on change (days): 0 (CISCO default)
          
Usage Reporting:
  Last ACK received: <none>
  Next ACK deadline: <none>
  Reporting push interval: 0 (no reporting)
  Next ACK push check: <none>
  Next report push: <none>
  Last report push: <none>
  Last report file write: <none>
          
Trust Code Installed: <none>
          
License Usage
=============
          
No licenses in use
          
Product Information
===================
UDI: PID:C9800-CL-K9,SN:9KGIXIDOXFE
          
HA UDI List:
    Active:PID:C9800-CL-K9,SN:9KGIXIDOXFE
    Standby:PID:C9800-CL-K9,SN:9UBKZU955E4
          
Agent Version
=============
Smart Agent for Licensing: 5.3.14_rel/47
          
License Authorizations
======================
Overall status:
  Active: PID:C9800-CL-K9,SN:9KGIXIDOXFE
      Status: NOT INSTALLED
  Standby: PID:C9800-CL-K9,SN:9UBKZU955E4
      Status: NOT INSTALLED
          
Purchased Licenses:
  No Purchase Information Available
          
Usage Report Summary:
=====================
Total: 0,  Purged: 0
Total Acknowledged Received: 0,  Waiting for Ack: 0
Available to Report: 0  Collecting Data: 0

Examples

The following is sample output of the show license all command on a Cisco Catalyst 9800-CL Wireless Controller. Similar output is displayed on all supported Cisco Catalyst Wireless Controllers.

Device# show license all

Smart Licensing Status
======================

Smart Licensing is ENABLED
License Reservation is ENABLED

Export Authorization Key:
  Features Authorized:
    <none>

Utility:
  Status: DISABLED

Smart Licensing Using Policy:
  Status: ENABLED

Data Privacy:
  Sending Hostname: yes
    Callhome hostname privacy: DISABLED
    Smart Licensing hostname privacy: DISABLED
  Version privacy: DISABLED

Transport:
  Type: Transport Off

Miscellaneous:
  Custom Id: <empty>

Policy:
  Policy in use: Merged from multiple sources.
  Reporting ACK required: yes (CISCO default)
  Unenforced/Non-Export Perpetual Attributes:
    First report requirement (days): 365 (CISCO default)
    Reporting frequency (days): 0 (CISCO default)
    Report on change (days): 90 (CISCO default)
  Unenforced/Non-Export Subscription Attributes:
    First report requirement (days): 90 (CISCO default)
    Reporting frequency (days): 90 (CISCO default)
    Report on change (days): 90 (CISCO default)
  Enforced (Perpetual/Subscription) License Attributes:
    First report requirement (days): 0 (CISCO default)
    Reporting frequency (days): 0 (CISCO default)
    Report on change (days): 0 (CISCO default)
  Export (Perpetual/Subscription) License Attributes:
    First report requirement (days): 0 (CISCO default)
    Reporting frequency (days): 0 (CISCO default)
    Report on change (days): 0 (CISCO default)

Usage Reporting:
  Last ACK received: <none>
  Next ACK deadline: <none>
  Reporting push interval: 0 (no reporting)
  Next ACK push check: Nov 01 20:31:46 2020 IST
  Next report push: <none>
  Last report push: <none>
  Last report file write: <none>

Trust Code Installed: <none>

License Usage
=============

air-network-advantage (DNA_NWStack):
  Description: air-network-advantage
  Count: 1
  Version: 1.0
  Status: IN USE
  Export status: NOT RESTRICTED
  Feature Name: air-network-advantage
  Feature Description: air-network-advantage
  Enforcement type: NOT ENFORCED
  License type: Perpetual
  Reservation: 
    Reservation status: SPECIFIC INSTALLED
    Total reserved count: 20

air-dna-advantage (AIR-DNA-A):
  Description: air-dna-advantage
  Count: 1
  Version: 1.0
  Status: IN USE
  Export status: NOT RESTRICTED
  Feature Name: air-dna-advantage
  Feature Description: air-dna-advantage
  Enforcement type: NOT ENFORCED
  License type: Perpetual
  Reservation: 
    Reservation status: SPECIFIC INSTALLED
    Total reserved count: 20

Product Information
===================
UDI: PID:C9800-CL-K9,SN:93BBAH93MGS

HA UDI List:
    Active:PID:C9800-CL-K9,SN:93BBAH93MGS
    Standby:PID:C9800-CL-K9,SN:9XECPSUU4XN

Agent Version
=============
Smart Agent for Licensing: 5.0.6_rel/47

License Authorizations
======================
Overall status:
  Active: PID:C9800-CL-K9,SN:93BBAH93MGS
      Status: SPECIFIC INSTALLED on Nov 02 03:16:01 2020 IST
      Last Confirmation code: 102fc949
  Standby: PID:C9800-CL-K9,SN:9XECPSUU4XN
      Status: SPECIFIC INSTALLED on Nov 02 03:15:45 2020 IST
      Last Confirmation code: ad4382fe

Specified license reservations:
  Aironet DNA Advantage Term Licenses (AIR-DNA-A):
    Description: DNA Advantage for Wireless
    Total reserved count: 20
    Enforcement type: NOT ENFORCED
    Term information:
      Active: PID:C9800-CL-K9,SN:93BBAH93MGS
        Authorization type: SPECIFIC INSTALLED on Nov 02 03:15:45 2020 IST
        License type: TERM
          Start Date: 2020-OCT-14 UTC
          End Date: 2021-APR-12 UTC
          Term Count: 5
        Authorization type: SPECIFIC INSTALLED on Nov 02 03:15:45 2020 IST
        License type: TERM
          Start Date: 2020-JUN-18 UTC
          End Date: 2020-DEC-15 UTC
          Term Count: 5
      Standby: PID:C9800-CL-K9,SN:9XECPSUU4XN
        Authorization type: SPECIFIC INSTALLED on Nov 02 03:15:45 2020 IST
        License type: TERM
          Start Date: 2020-OCT-14 UTC
          End Date: 2021-APR-12 UTC
          Term Count: 10
  AP Perpetual Networkstack Advantage (DNA_NWStack):
    Description: AP Perpetual Network Stack entitled with DNA-A
    Total reserved count: 20
    Enforcement type: NOT ENFORCED
    Term information:
      Active: PID:C9800-CL-K9,SN:93BBAH93MGS
        Authorization type: SPECIFIC INSTALLED on Nov 02 03:15:45 2020 IST
        License type: TERM
          Start Date: 2020-OCT-14 UTC
          End Date: 2021-APR-12 UTC
          Term Count: 5
        Authorization type: SPECIFIC INSTALLED on Nov 02 03:15:45 2020 IST
        License type: TERM
          Start Date: 2020-JUN-18 UTC
          End Date: 2020-DEC-15 UTC
          Term Count: 5
      Standby: PID:C9800-CL-K9,SN:9XECPSUU4XN
        Authorization type: SPECIFIC INSTALLED on Nov 02 03:15:45 2020 IST
        License type: TERM
          Start Date: 2020-OCT-14 UTC
          End Date: 2021-APR-12 UTC
          Term Count: 10

Purchased Licenses:
  No Purchase Information Available

show license authorization

To display authorization-related information for (export-controlled and enforced) licenses, enter the show license authorization command in privileged EXEC mode.

show license authorization

Syntax Description


This command has no keywords or arguments

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.3.2a	This command was introduced.

Usage Guidelines

Only export-controlled or enforced licenses require authorization before use.

While there are no export-controlled or enforced licenses on Cisco Catalyst Wireless Controllers, you can use this command to display migrated SLR authorization codes.

Examples

See Table 1 for information about fields shown in the display.

See show license authorization Displaying Migrated Authorization Code for sample output.

Table 6. show license authorization Field Descriptions
Field		Description
Overall Status	Header for UDI information for all product instances in the set-up, the type of authorization that is installed, and configuration errors, if any. In a High Availability set-up, all UDIs in the set-up are listed.
	Active: Status:	The active product instance UDI, followed by the status of the authorization code installation for this UDI. If the status indicates that the authorization code is installed and there is a confirmation code, this is also displayed.
	Standby: Status:	The standby product instance UDI, followed by the status of the authorization code installation for this UDI. If the status indicates that the authorization code is installed and there is a confirmation code, this is also displayed.
	Member: Status:	The member product instance UDI, followed by the status of the authorization code installation for this UDI. If the status indicates that the authorization code is installed and there is a confirmation code, this is also displayed.
	ERROR:	Configuration errors or discrepancies in the High Availability set-up, if any.
Authorizations	Header for detailed license authorization information. All licenses, their enforcement types, and validity durations are displayed. Errors are displayed for each product instance if its authorization or mode does not match what is installed on the active. This section is displayed only if the product instance is using a license with an authorization code.
	():	License name and a shortened form of the license name.
	Description	License description.
	Total available count:	Total count of licenses that are available to consume. This includes licenses of all durations (perpetual and subscription), including expired subscription licenses, for all the product instances in a High Availability setup.
	Enforcement type	Enforcement type for the license. This may be one of the following: Enforced Not enforced Export-Controlled
	Term information:	Header providing license duration information. The following fields maybe included under this header: Active: The active product instance UDI, followed by the status of the authorization code installation for this UDI. Authorization type: Type of authorization code installed and date of installation. The type can be: SLAC, UNIVERSAL, SPECIFIED, PAK, RTU. Start Date: Displays validity start date if the license is for a specific term or time period. Start Date: Displays validity end date if the license is for a specific term or time period. Term Count: License count. Subscription ID: Displays ID if the license is for a specific term or time period. License type: License duration. This can be: SUBSCRIPTION or PERPETUAL. Standby: The standby product instance UDI, followed by the status of the authorization code installation for this UDI. Member: The member product instance UDI, followed by the status of the authorization code installation for this UDI. For more information about the duration or term of a license's validity, see <link tbd>.
Purchased Licenses	Header for license purchase information.
	Active:	The active product instance and its the UDI.
	Count:	License count.
	Description:	License description.
	License type:	License duration. This can be: SUBSCRIPTION or PERPETUAL.
	Standby:	The standby product instance UDI.
	Member:	The member product instance UDI.

Examples

The following is sample output of the show license authorization command on a Cisco Catalyst 9800-CL Wireless Controller. The Last Confirmation code: shows that SLR authorization code is available after migration. Similar output is displayed on all supported Cisco Catalyst Wireless Controllers.

Device# show license authorization
Overall status:
  Active: PID:C9800-CL-K9,SN:93BBAH93MGS
      Status: SPECIFIC INSTALLED on Nov 02 03:16:01 2020 IST
      Last Confirmation code: 102fc949
  Standby: PID:C9800-CL-K9,SN:9XECPSUU4XN
      Status: SPECIFIC INSTALLED on Nov 02 03:15:45 2020 IST
      Last Confirmation code: ad4382fe

Specified license reservations:
  Aironet DNA Advantage Term Licenses (AIR-DNA-A):
    Description: DNA Advantage for Wireless
    Total reserved count: 20
    Enforcement type: NOT ENFORCED
    Term information:
      Active: PID:C9800-CL-K9,SN:93BBAH93MGS
        Authorization type: SPECIFIC INSTALLED on Nov 02 03:15:45 2020 IST
        License type: TERM
          Start Date: 2020-OCT-14 UTC
          End Date: 2021-APR-12 UTC
          Term Count: 5
        Authorization type: SPECIFIC INSTALLED on Nov 02 03:15:45 2020 IST
        License type: TERM
          Start Date: 2020-JUN-18 UTC
          End Date: 2020-DEC-15 UTC
          Term Count: 5
      Standby: PID:C9800-CL-K9,SN:9XECPSUU4XN
        Authorization type: SPECIFIC INSTALLED on Nov 02 03:15:45 2020 IST
        License type: TERM
          Start Date: 2020-OCT-14 UTC
          End Date: 2021-APR-12 UTC
          Term Count: 10
  AP Perpetual Networkstack Advantage (DNA_NWStack):
    Description: AP Perpetual Network Stack entitled with DNA-A
    Total reserved count: 20
    Enforcement type: NOT ENFORCED
    Term information:
      Active: PID:C9800-CL-K9,SN:93BBAH93MGS
        Authorization type: SPECIFIC INSTALLED on Nov 02 03:15:45 2020 IST
        License type: TERM
          Start Date: 2020-OCT-14 UTC
          End Date: 2021-APR-12 UTC
          Term Count: 5
        Authorization type: SPECIFIC INSTALLED on Nov 02 03:15:45 2020 IST
        License type: TERM
          Start Date: 2020-JUN-18 UTC
          End Date: 2020-DEC-15 UTC
          Term Count: 5
      Standby: PID:C9800-CL-K9,SN:9XECPSUU4XN
        Authorization type: SPECIFIC INSTALLED on Nov 02 03:15:45 2020 IST
        License type: TERM
          Start Date: 2020-OCT-14 UTC
          End Date: 2021-APR-12 UTC
          Term Count: 10

Purchased Licenses:
  No Purchase Information Available

show license data conversion

To display license data conversion information, enter the show license data command in privileged EXEC mode.

show license data conversion

Syntax Description


This command has no keywords or arguments

Command Modes

Privileged EXEC (Device#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.
Cisco IOS XE Amsterdam 17.3.2a	This command continues to be available with the introduction of Smart Licensing Using Policy.

Usage Guidelines

Although visible on the CLI, this command is not applicable to Cisco Catalyst Wireless Controllers.

show license eventlog

To display event logs relating to Smart Licensing Using Policy, enter the show license eventlog command in privileged EXEC mode.

show license eventlog [ days ]

Syntax Description


`days`	Enter the number of days for which you want to display event logs. The valid value range is from 0 to 2147483647.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.
Cisco IOS XE Amsterdam 17.3.2a	Additional events were added with the introduction of Smart Licensing Using Policy: Installation and removal of a policy Request, installation and removal of an authorization code. Installation and removal of a trust code. Addition of authorization source information for license usage.

Usage Guidelines

Smart Licensing Using Policy: If the software version on the device (also referred to as a product instance) is Cisco IOS XE Amsterdam 17.3.2a or a later release, command output displays fields pertinent to Smart Licensing Using Policy.

Smart Licensing: If the software version on the device is Cisco IOS XE Amsterdam 17.3.1 or an earlier release, command output displays fields pertinent to Smart Licensing.

show license history message

To display communication history between the product instance and CSSM or CSLU (as the case may be), enter the show license history message command in privileged EXEC mode. The output of this command is used by the technical support team, for troubleshooting.

show license history message

Syntax Description


This command has no keywords or arguments.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.3.2a	This command was introduced.

Usage Guidelines

When you encounter an error message that you are not able to resolve, along with a copy of the message that appears on the console or in the system log, provide your Cisco technical support representative with sample output of these commands: show license tech support , show license history message , and the show platform software sl-infra privileged EXEC commands.

show license reservation

To display license reservation information, enter the show license reservation command in privileged EXEC mode.

show license reservation

Syntax Description


This command has no keywords or arguments

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.
Cisco IOS XE Amsterdam 17.3.2a	This command continues to be available with the introduction of Smart Licensing Using Policy.

Usage Guidelines

The command continues to be available on the CLI and corresponding output is displayed, but with the introduction of Smart Licensing Using Policy, the notion of reservation is not longer applicable. Use the show license all command in privileged EXEC mode, to display migrated SLR licenses instead (the SLR authorization code is migrated to Smart Licensing Using Policy).

show license rum

To display information about Resource Utilization Measurement reports (RUM report) available on the product instance, including report IDs, the current processing state of a report, error information (if any), and to save the detailed or summarized view that is displayed, enter the show license rum command in privileged EXEC mode.

show license rum { feature { license_name | all } | id { rum_id | all } } [ detail ] [ save path ]

Syntax Description

feature { license_name | all }

Displays RUM report information based on the license name.

Specify a particular license name to display all RUM reports for that license, or use the all keyword to display all RUM reports available on the product instance.

id { rum_id | all }

Displays RUM report information based on the RUM report ID.

Specify a report ID to display information for a single report, or use the all keyword to display all RUM reports available on the product instance.

detail

Displays detailed RUM report information.

You can use this to display detailed information by license name and detailed information by RUM report ID.

save path

Saves the information that is displayed. This can be the simplified or detailed version and depends on the preceeding keywords you have entered.

Information about 200 RUM reports can be displayed. If there are more 200 RUM reports on the product instance, you can view information about all the RUM reports by saving it to a text (.txt) file.

Note

This option saves the information about RUM reports and is not for reporting purposes. It does not save the RUM report, which is an XML file containing usage information.

Command Modes

Privileged EXEC (Device#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.7.1	This command was introduced.

Usage Guidelines

A RUM report is a license usage report, which the product instance generates, to fulfil reporting requirements as specified by the policy. An acknowledgement (ACK) is a response from CSSM and provides information about the status of a RUM report. Once the ACK for a report is available on the product instance, it indicates that the corresponding RUM report is no longer required and can be deleted. You can use the show license rum command to:

Display information about the available RUM reports on the product instance - filtered by ID or license name.
Display a short summary of the information or display a detailed view of the information.
Track a RUM report throughout its lifecycle (from the time it is first generated until its acknowledgement from CSSM). By displaying the current processing state and condition of a report you can ascertain if and when there is a problem in the reporting workflow.
Save the displayed information. The CLI displays information about up to 200 reports. If there are more than 200 reports on the product instance and you want to view information about all of them, save the displayed info in a .txt file and export to the desired location to view.

To display a statistical view of RUM report information (the total number of reports on the product instance, the number of reports that have a corresponding ACK, the number of reports waiting for an ACK etc.) refer to the Usage Report Summary: section of the show license all and show license tech privileged EXEC commands.

The show license tech command also provides RUM report related information that the Cisco technical support team can use to troubleshoot, if there are problems with RUM reporting.

Examples

For information about fields shown in the display, see show-commands.html#__ and show-commands.html#__

For sample output of the show license rum command, see:

Field Name

Description

Report Id

A numeric field that identifies a RUM report. The product instance automatically assigns an ID to every RUM report it generates. An ID may be up to 20 characters long.

State

This field displays the current processing state of a RUM report, and can be only one of the following:

OPEN: This means new measurements are been added into this report.
CLOSED: This means no new measurements can be added to this report, and the report is ready for communication to CSSM.
PENDING: This is a transitional status that you may see if you display a report while it is being transmitted.
UNACK: This means the report was transmitted and is waiting for confirmation from CSSM, that it is processed.
ACK: This means the report was processed or acknowledged by CSSM and is eligible for deletion.

Flag

Indicates the condition of the RUM report, and is displayed in the form of a character. Each character represents a specific condition, and can be only one of the following values:

N: Normal; This means no errors have been detected and the report is going through normal operation.
P: Purged; This means the report was removed due to system resource limitation, and can refer to a shortage of disk space or insufficient memory. If this flag is displayed, refer to the State Change Reason field in the detailed view for more information.

E: Error; This means an error was detected in the RUM report. If this flag is displayed, refer to the detailed view for more information. Possible workflow issues include and are not limited to the following:

RUM report was dropped by CSSM. If this is the issue, the State field displays value ACK, but the State Change Reason does not change to ACKED.
RUM Report data is missing. If this is the issue, the Storage State field displays value MISSING .
Tracking information is missing. If this is the case the State field displays value UNACK and the Transaction ID field has no information.

Note

Occasional errors in RUM reports do not require any action from you and are not an indication of a problem. It is only if you see a large number of reports (greater than 10) with errors that you must contact the Cisco technical support team.

Feature Name

The name of the license that the RUM report applies to.

Table 8. show license rum (detailed view) Field Descriptions
Field Name	Description
Report Id	A numeric field that identifies a RUM report. The product instance automatically assigns an ID to every RUM report it generates. An ID may be up to 20 characters long.
Metric Name:	Shows the type of data that is recorded. For a RUM report, the only possible value is ENTITLEMENT, and refers to measurement of license usage.
Feature Name:	The name of the license that the RUM report applies to.
Metric Value	A unique identifier for the data that is recorded. This is the same as the “Entitlement Tag” in the output of the show license tech commad and it displays information about the license being tracked.
UDI	Composed of the Product ID (PID) and serial number of the product instance.
Previous Report Id:	ID of the previous RUM report that the product instance generated for a license.
Next Report Id:	The ID that the product instance will use for the next RUM report it generates for a llicense.
State:	Displays the current processing state of a RUM report. The value displayed here is always the same as the value displayed in the simplified view. For the list of possible values see show-commands.html#__above.
State Change Reason:	Displays the reason for a RUM report state change. Not all state changes provide a reason. NONE: This means the RUM report is going through its normal lifecycle (for instance, from OPEN → CLOSED → ACK). This state change reason is usually accompanied by an `N` flag (meaning Normal) in the simplified view and requires no action from you. ACKED: RUM report was processed normally by CSSM. REMOVED: RUM report was received and requested to be removed by CSSM. RELOAD: RUM report state was changed due to some type of device reload.
Start Time:	Timestamps for measurement start and measurement end for a RUM report. Together, the start time and end time provide the time duration that the measurements cover.
End Time:
Storage State:	Displays current storage state of the RUM report and can be one of the following values: EXIST: This means the data for the RUM report is located in storage. DELETED: This means the data was intentionally deleted. Refer to the `Storage State Change Reason` in the output of the show license tech command for more information about this storage state. PURGED: This means the data was deleted due to a system resource limitation. Refer to the `Storage State Change Reason` in the output of the show license tech command for more information about this storage state. MISSING: This means data is missing from storage. If reports are identified as missing, there is no recovery process.
Transaction ID:	Contains tracking information for the RUM report. This information can be either polling information or ACK import information. The Transaction Message contains the error message, if the product instance receives one when importing an ACK. The information in these fields is used by the Cisco technical support team when troubleshooting problems with RUM reports.
Transaction Message:

Examples

The following is sample output of the show license rum featurelicense-name and show license rum featurelicense-namedetail commands on a Cisco Catalyst 9500 Series Switch. Similar output is displayed on all other Catalyst switches.

The output is filtered to display all RUM reports for the DNA Advantage license, followed by a detailed view of all RUM reports for the DNA Advantage license.

Device# show license rum feature air-dna-advantage

Smart Licensing Usage Report:

====================================

Report Id,          State,    Flag, Feature Name

1638055644          CLOSED    N     air-dna-advantage

1638055646          OPEN      N     air-dna-advantage


Device# show license rum feature air-dna-advantage detail 
Smart Licensing Usage Report Detail:
====================================
Report Id: 1638055644
  Metric Name: ENTITLEMENT
  Feature Name: air-dna-advantage
  Metric Value: regid.2017-08.com.cisco.AIR-DNA-A,1.0_b6308627-3ab0-4a11-a3d9-586911a0d790
  UDI: PID:C9800-CL-K9,SN:93SZ7RXN93Y
  Previous Report Id: 0,    Next Report Id: 1638055646
  State: CLOSED,      State Change Reason: RELOAD
  Start Time: Nov 28 12:02:09 2021 UTC,      End Time: Nov 30 22:02:13 2021 UTC
  Storage State: EXIST
  Transaction ID: 0
  Transaction Message: <none>

Report Id: 1638055646
  Metric Name: ENTITLEMENT
  Feature Name: air-dna-advantage
  Metric Value: regid.2017-08.com.cisco.AIR-DNA-A,1.0_b6308627-3ab0-4a11-a3d9-586911a0d790
  UDI: PID:C9800-CL-K9,SN:93SZ7RXN93Y
  Previous Report Id: 1638055644,    Next Report Id: 0
  State: OPEN,      State Change Reason: None
  Start Time: Nov 30 23:12:56 2021 UTC,      End Time: Dec 01 02:12:56 2021 UTC
  Storage State: EXIST
  Transaction ID: 0
  Transaction Message: <none>

Examples

The following example shows you how to save the information that is displayed.

By using the feature and all keywords, the output is filtered to display all RUM reports for all licenses being used on the product instance. It is then transferred it to a TFTP location, from where it can opened, to view the information.

Device# show license rum feature all save bootflash:all-rum-stats.txt 
Device# copy tftp://10.8.0.6/bootflash:all-rum-stats.txt

show license status

To display information about licensing settings such as data privacy, policy, transport, usage reporting and trust codes, enter the show license status command in privileged EXEC mode.

show license status

Syntax Description


This command has no keywords or arguments

Command Modes

Privileged EXEC (Device#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.
Cisco IOS XE Amsterdam 17.3.2a	Command output was updated to reflect new fields that are applicable to Smart Licensing Using Policy. This includes `Trust code installed:`, `Policy in use`, `Policy name:` , reporting requirements as in the policy (`Attributes:` ), and fields related to usage reporting. Command output no longer displays Smart Account and Virtual account information.
Cisco IOS XE Cupertino 17.7.1	Command output was updated to display Smart Account and Virtual account information.

Usage Guidelines

Smart Licensing: If the software version on the device is Cisco IOS XE Amsterdam 17.3.1 or an earlier release, command output displays fields pertinent to Smart Licensing.

Smart Licensing Using Policy: If the software version on the device (also referred to as a product instance) is Cisco IOS XE Amsterdam 17.3.2a or a later release, command output displays fields pertinent to Smart Licensing Using Policy.

Account Information in the output

Starting with Cisco IOS XE Cupertino 17.7.1, every ACK includes the Smart Account and Virtual Account that was reported to, in CSSM. When it receives the ACK, the product instance securely stores only the latest version of this information - as determined by the timestamp in the ACK. The Smart Account and Virtual Account information that is displayed in the Account Information section of this command's output is therefore always as per the latest available ACK on the product instance.

If a product instance is moved from one Smart Account and Virtual Account to another, the next ACK after the move will have this updated information. The output of this command is updated once this ACK is available on the product instance.

The ACK may be received directly (where the product instance is connected to CSSM), or indirectly (where the product instance is connect to CSSM through CSLU, Cisco DNA Center, or SSM On-Prem), or by manually importing the ACK (where a product instance is in an air-gapped network).

Examples

For information about the fields shown in the display, see Table 1 .

For sample output, see:

Field

Description

Utility

Header for utility settings that are configured on the product instance.

Status:

Status

Utility report:

Last attempt:

Customer Information:

The following fields are displayed:

Id:
Name:
Street
City:
State:
Country:
Postal Code:

Smart Licensing Using Policy:

Header for policy settings on the product instance.

Status:

Indicates if Smart Licensing Using Policy is enabled.

Smart Licensing Using Policy is supported starting from Cisco IOS XE Amsterdam 17.3.2 and is always enabled on supported software images.

Account Information:

Header for account information that the product instance belongs to, in CSSM.

This section is displayed only if the software version on the product instance is Cisco IOS XE Cupertino 17.7.1 or a later release.

Smart Account:

The Smart Account that the product instance is part of. This information is always as per the latest available ACK on the product instance.

Virtual Account:

The Virtual Account that the product instance is part of. This information is always as per the latest available ACK on the product instance.

Data Privacy:

Header for privacy settings that are configured on the product instance.

Sending Hostname:

A yes or no value which shows if the hostname is sent in usage reports.

Callhome hostname privacy:

Indicates if the Call Home feature is configured as the mode of transport for reporting. If configured, one of these values is displayed:

ENABLED
DISABLED

Smart Licensing hostname privacy:

One of these values is displayed:

ENABLED
DISABLED

Version privacy:

One of these values is displayed:

ENABLED
DISABLED

Transport:

Header for transport settings that are configured on the product instance.

Type:

Mode of transport that is in use.

Additional fields are displayed for certain transport modes. For example, if transport type is set to CSLU, the CSLU address is also displayed.

Policy:

Header for policy information that is applicable to the product instance.

Policy in use:

Policy that is applied

This can be one of the following: Cisco default, Product default, Permanent License Reservation, Specific License Reservation, PAK license, Installed on <date>, Controller.

Policy name:

Name of the policy

Reporting ACK required:

A yes or no value which specifies if the report for this product instance requires CSSM acknowledgement (ACK) or not. The default policy is always set to “yes”.

Unenforced/Non-Export Perpetual Attributes

Displays policy values for perpetual licenses.

First report requirement (days): The maximum amount of time available before the first report must be sent, followed by policy name.
Reporting frequency (days): The maximum amount of time available before the subsequent report must be sent, followed by policy name.
Report on change (days): he maximum amount of time available to send a report in case of a change in license usage, followed by policy name

Unenforced/Non-Export Subscription Attributes

Displays policy values for subscription licenses.

First report requirement (days): The maximum amount of time available before the first report must be sent, followed by policy name.
Reporting frequency (days): The maximum amount of time available before the subsequent report must be sent, followed by policy name.
Report on change (days): he maximum amount of time available to send a report in case of a change in license usage, followed by policy name

Enforced (Perpetual/Subscription) License Attributes

Displays policy values for enforced licenses.

First report requirement (days): The maximum amount of time available before the first report must be sent, followed by policy name.
Reporting frequency (days): The maximum amount of time available before the subsequent report must be sent, followed by policy name.
Report on change (days): The maximum amount of time available to send a report in case of a change in license usage, followed by policy name

Export (Perpetual/Subscription) License Attributes

Displays policy values for export-controlled licenses.

First report requirement (days): The maximum amount of time available before the first report must be sent, followed by policy name.
Reporting frequency (days): The maximum amount of time available before the subsequent report must be sent, followed by policy name.
Report on change (days): The maximum amount of time available to send a report in case of a change in license usage, followed by policy name

Miscellaneous

Header for custom ID.

Custom Id:

ID

Usage Reporting:

Header for usage reporting (RUM reports) information.

Last ACK received:

Date and time of last ACK received, in the local time zone.

Next ACK deadline:

Date and time for next ACK. If the policy states that an ACK is not requires then this field displays none.

Note

If an ACK is required and is not received by this deadline, a syslog is displayed.

Reporting Interval:

Reporting interval in days

The value displayed here depends on what you configure in the license smart usage intervalinterval_in_days and the policy value. For more information, see the corresponding Syntax Description: license smart (global config).

Next ACK push check:

Date and time when the product instance will submit the next polling request for an ACK. Date and time are in the local time zone.

This applies only to product instance- initiated communication to CSSM or CSLU. If the reporting interval is zero, or if no ACK polling is pending, then this field displays none.

Next report push:

Date and time when the product instance will send the next RUM report. Date and time are in the local time zone. If the reporting interval is zero, or if there are no pending RUM reports, then this field displays none.

Last report push:

Date and time for when the product instance sent the last RUM report. Date and time are in the local time zone.

Last report file write:

Date and time for when the product instance last saved an offline RUM report. Date and time are in the local time zone.

Last report pull:

Date and time for when usage reporting information was retrieved using data models. Date and time are in the local time zone.

Trust Code Installed:

Header for trust code-related information.

Displays date and time if trust code is installed. Date and time are in the local time zone.

If a trust code is not installed, then this field displays none.

Active:

Active product instance.

In a High Availability set-up, the the UDIs of all product instances in the set-up, along with corresponding trust code installation dates and times are displayed.

Standby:

Standby product instance.

Member:

Member product instance

show license status with Account Information (Smart Licensing Using Policy)

The following is sample output of the show license status command, on a product instance where the software version is Cisco IOS XE Cupertino 17.7.1:

Device# show license status
Utility:
  Status: DISABLED

Smart Licensing Using Policy:
  Status: ENABLED

Account Information:
  Smart Account: Eg-SA
  Virtual Account: Eg-VA

Data Privacy:
  Sending Hostname: yes
    Callhome hostname privacy: DISABLED
    Smart Licensing hostname privacy: DISABLED
  Version privacy: DISABLED

Transport:
  Type: Smart
  URL: https://smartreceiver.cisco.com/licservice/license
  Proxy:
    Not Configured
  VRF:
    Not Configured
          
Policy:   
  Policy in use: Merged from multiple sources.
  Reporting ACK required: yes (CISCO default)
  Unenforced/Non-Export Perpetual Attributes:
    First report requirement (days): 365 (CISCO default)
    Reporting frequency (days): 0 (CISCO default)
    Report on change (days): 90 (CISCO default)
  Unenforced/Non-Export Subscription Attributes:
    First report requirement (days): 90 (CISCO default)
    Reporting frequency (days): 90 (CISCO default)
    Report on change (days): 90 (CISCO default)
  Enforced (Perpetual/Subscription) License Attributes:
    First report requirement (days): 0 (CISCO default)
    Reporting frequency (days): 0 (CISCO default)
    Report on change (days): 0 (CISCO default)
  Export (Perpetual/Subscription) License Attributes:
    First report requirement (days): 0 (CISCO default)
    Reporting frequency (days): 0 (CISCO default)
    Report on change (days): 0 (CISCO default)
          
Miscellaneous:
  Custom Id: <empty>
          
Usage Reporting:
  Last ACK received: <none>
  Next ACK deadline: <none>
  Reporting push interval: 0 (no reporting)
  Next ACK push check: <none>
  Next report push: <none>
  Last report push: <none>
  Last report file write: <none>
          
Trust Code Installed: <none>

show license status with Cisco Default Policy (Smart Licensing Using Policy)

The following is sample output of the show license status command; a default is policy applied here.

Device# show license status

Utility:
  Status: DISABLED

Smart Licensing Using Policy:
  Status: ENABLED

Data Privacy:
  Sending Hostname: yes
    Callhome hostname privacy: DISABLED
    Smart Licensing hostname privacy: DISABLED
  Version privacy: DISABLED

Transport:
  Type: Smart
  URL: https://smartreceiver.cisco.com/licservice/license
  Proxy:
    Not Configured

Policy:
  Policy in use: Merged from multiple sources.
  Reporting ACK required: yes (CISCO default)
  Unenforced/Non-Export Perpetual Attributes:
    First report requirement (days): 365 (CISCO default)
    Reporting frequency (days): 0 (CISCO default)
    Report on change (days): 90 (CISCO default)
  Unenforced/Non-Export Subscription Attributes:
    First report requirement (days): 90 (CISCO default)
    Reporting frequency (days): 90 (CISCO default)
    Report on change (days): 90 (CISCO default)
  Enforced (Perpetual/Subscription) License Attributes:
    First report requirement (days): 0 (CISCO default)
    Reporting frequency (days): 0 (CISCO default)
    Report on change (days): 0 (CISCO default)
  Export (Perpetual/Subscription) License Attributes:
    First report requirement (days): 0 (CISCO default)
    Reporting frequency (days): 0 (CISCO default)
    Report on change (days): 0 (CISCO default)

Miscellaneous:
  Custom Id: <empty>

Usage Reporting:
  Last ACK received: <none>
  Next ACK deadline: <none>
  Reporting push interval: 0 (no reporting)
  Next ACK push check: <none>
  Next report push: <none>
  Last report push: <none>
  Last report file write: <none>

Trust Code Installed: <none>

show license status with Custom Policy (Smart Licensing Using Policy)

The following is sample output of the show license status command; a custom policy applied here.

Device# show license status 
Utility:
  Status: DISABLED

Smart Licensing Using Policy:
  Status: ENABLED

Data Privacy:
  Sending Hostname: yes
    Callhome hostname privacy: DISABLED
    Smart Licensing hostname privacy: DISABLED
  Version privacy: DISABLED

Transport:
  Type: Smart
  URL: https://smartreceiver.cisco.com/licservice/license
  Proxy:
    Not Configured

Policy:
  Policy in use: Installed On Nov 02 05:09:31 2020 IST
  Policy name: SLE Policy
  Reporting ACK required: yes (Customer Policy)
  Unenforced/Non-Export Perpetual Attributes:
    First report requirement (days): 60 (Customer Policy)
    Reporting frequency (days): 60 (Customer Policy)
    Report on change (days): 60 (Customer Policy)
  Unenforced/Non-Export Subscription Attributes:
    First report requirement (days): 30 (Customer Policy)
    Reporting frequency (days): 30 (Customer Policy)
    Report on change (days): 30 (Customer Policy)
  Enforced (Perpetual/Subscription) License Attributes:
    First report requirement (days): 0 (CISCO default)
    Reporting frequency (days): 90 (Customer Policy)
    Report on change (days): 90 (Customer Policy)
  Export (Perpetual/Subscription) License Attributes:
    First report requirement (days): 0 (CISCO default)
    Reporting frequency (days): 90 (Customer Policy)
    Report on change (days): 90 (Customer Policy)

Miscellaneous:
  Custom Id: <empty>

Usage Reporting:
  Last ACK received: <none>
  Next ACK deadline: <none>
  Reporting push interval: 0 (no reporting)
  Next ACK push check: <none>
  Next report push: <none>
  Last report push: <none>
  Last report file write: <none>

Trust Code Installed:
  Active: PID:C9800-CL-K9,SN:93BBAH93MGS
    INSTALLED on Nov 02 05:09:31 2020 IST
  Standby: PID:C9800-CL-K9,SN:9XECPSUU4XN
    INSTALLED on Nov 02 05:09:31 2020 IST

show license summary

To display a brief summary of license usage, which includes information about licenses being used, the count, and status, enter the show license summary command in privileged EXEC mode.

show license summary

Syntax Description


This command has no keywords or arguments

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.
Cisco IOS XE Amsterdam 17.3.2a	Command output was updated to reflect valid license status for Smart Licensing Using Policy. Valid license statuses include: `IN USE`, `NOT IN USE`, `NOT AUTHORIZED`. Command output was also updated to remove registration and authorization information. Command output no longer displays Smart Account and Virtual account information.
Cisco IOS XE Cupertino 17.7.1	Command output was updated to display Smart Account and Virtual account information.

Usage Guidelines

Smart Licensing: If the software version on the device is Cisco IOS XE Amsterdam 17.3.1 or an earlier release, command output displays fields pertinent to Smart Licensing.

Smart Licensing Using Policy: If the software version on the device (also referred to as a product instance) is Cisco IOS XE Amsterdam 17.3.2a or a later release, command output displays fields pertinent to Smart Licensing Using Policy.

The licenses on Cisco Catalyst Wireless Controllers are never NOT AUTHORIZED, because none of the available licenses are export-controlled or enforced (Only these licenses require authorization before use).

Account Information in the output

Starting with Cisco IOS XE Cupertino 17.7.1, every ACK includes the Smart Account and Virtual Account that was reported to, in CSSM. When it receives the ACK, the product instance securely stores only the latest version of this information - as determined by the timestamp in the ACK. The Smart Account and Virtual Account information that is displayed in the Account Information section of this command's output is therefore always as per the latest available ACK on the product instance.

If a product instance is moved from one Smart Account and Virtual Account to another, the next ACK after the move will have this updated information. The output of this command is updated once this ACK is available on the product instance.

The ACK may be received directly (where the product instance is connected to CSSM), or indirectly (where the product instance is connect to CSSM through CSLU, Cisco DNA Center, or SSM On-Prem), or by manually importing the ACK (where a product instance is in an air-gapped network).

Examples

See Table 1 for information about fields shown in the display.

show license summary: IN USE (Smart Licensing Using Policy)

show license summary: NOT IN USE (Smart Licensing Using Policy)

Table 10. show license summary Field Descriptions
Field	Description
Account Information: Smart Account: Virtual Account:	The Smart Account and Virtual Account that the product instance is part of. This information is always as per the latest available ACK on the product instance. This field is displayed only if the software version on the product instance is Cisco IOS XE Cupertino 17.7.1 or a later release.
License	Name of the licenses in use
Entitlement Tag	Short name for license
Count	License count
Status	License status can be one of the following In-Use: Valid license, and in-use. Not In-Use Not Authorized: Means that the license requires installation of SLAC before use.

show license summary: IN USE (Smart Licensing Using Policy)

The following is sample output of the show license summary command, on a product instance where the software version is Cisco IOS XE Cupertino 17.7.1:

Devide# show license summary

Account Information:
  Smart Account: Eg-SA
  Virtual Account: Eg-VA

License Usage:
  License                 Entitlement Tag               Count Status
  -----------------------------------------------------------------------------
  air-network-essentials  (DNA_NWSTACK_E)                   1 IN USE
  air-dna-essentials      (AIR-DNA-E)                       1 IN USE

show license summary: NOT IN USE (Smart Licensing Using Policy)

The following is sample output of the show license summary command, where no APs have joined the controller. Current consumption (Count) is therefore zero, and the Status field shows that the licenses are NOT IN USE:

Device# show license summary

Device#show license summary
License Reservation is ENABLED

License Usage:
  License                 Entitlement Tag               Count Status
  -----------------------------------------------------------------------------
  Aironet DNA Advantag... (AIR-DNA-A)                       0 NOT IN USE
  AP Perpetual Network... (DNA_NWStack)                     0 NOT IN USE

show license tech

To display licensing information to help the technical support team to solve a problem, enter the show license tech command in privileged EXEC mode. The output for this command includes outputs of several other show license commands and more.

show license tech { message | rum { feature { license_name | all } | id { rum_id | all } } [ detail ] [ save path ] | support }

Syntax Description

message

Displays messages concerning trust establishment, usage reporting, result polling, authorization code requests and returns, and trust synchronization.

This is the same information as displayed in the output of the show license history message command.

rum { feature { license_name | all } | id { rum_id | all } } [ detail ] [ save path ]

Displays information about Resource Utilization Measurement reports (RUM reports) on the product instance, including report IDs, the current processing state of a report, error information (if any), and an option save the displayed RUM report information.

Note

This option saves the information about RUM reports and is not for reporting purposes. It does not save the RUM report, which is an XML file containing usage information.

support

Displays licensing information that helps the technical support team to debug a problem.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.
Cisco IOS XE Amsterdam 17.3.2a	Command output was updated to reflect new fields that are applicable to Smart Licensing Using Policy.
Cisco IOS XE Cupertino 17.7.1	The rum keyword and additional options under this keyword were added: { feature { `license_name` \| all } \| id { `rum_id` \| all } } The output of the show license tech support command was enhanced to display the following information: RUM report information, in section `License Usage` and `Usage Report Summary`. Smart Account and Virtual account information, in section `Account Information:`. The data conversion , eventlog and reservation keywords were removed from this command. They continute to be available as separate show commands, that is, show license data , show license eventlog , and show license reservation respectively.

Usage Guidelines

Smart Licensing: If the software version on the device is Cisco IOS XE Amsterdam 17.3.1 or an earlier release, command output displays fields pertinent to Smart Licensing (whether smart licensing is enabled, all associated licensing certificates, compliance status, and so on).

Smart Licensing Using Policy: If the software version on the device (also referred to as a product instance) is Cisco IOS XE Amsterdam 17.3.2 or a later release, command output displays fields pertinent to Smart Licensing Using Policy. Note the following guidelines:

Troubleshooting with a Support Representative

When you encounter an error message that you are not able to resolve, along with a copy of the message that appears on the console or in the system log, provide your Cisco technical support representative with sample output of these commands: show license tech support , show license history message , and the show platform software sl-infra all privileged EXEC commands.

RUM Report Information in the output

The output of the show license tech support command displays the following sections pertaining to RUM reports:

Table 1

<output truncated>
License Usage
=============
  Measurements:
    ENTITLEMENT:
      Interval: 00:15:00
      Current Value: 800
      Current Report: 1638055645       Previous: 0
 <output truncated>

Table 2

<output truncated>
Usage Report Summary:
=====================
Total: 4,  Purged: 0(0)
Total Acknowledged Received: 0,  Waiting for Ack: 0(4)
Available to Report: 4  Collecting Data: 2  
Maximum Display: 4  In Storage: 4,  MIA: 0(0)
Report Module Status: Ready

<output truncated>

The output of the show license tech rum command when used with the detail keyword, displays the following fields pertaining to RUM reports: Table 3.

The options available under the show license tech rum keyword are the same as the options available with the show license rum privileged EXEC command. The sample output that is displayed in the simplified view is also the same. But if you use the detail keyword (for example if you enter show license tech rum feature license_name detail ), the detailed view is displayed and this has a few additional fields when compared to show license rum .

<output truncated>
Smart Licensing Usage Report Detail:
====================================
Report Id: 1638055644
  Metric Name: ENTITLEMENT
  Feature Name: air-dna-advantage
  Metric Value: regid.2017-08.com.cisco.AIR-DNA-A,1.0_b6308627-3ab0-4a11-a3d9-586911a0d790
  UDI: PID:C9800-CL-K9,SN:93SZ7RXN93Y
  Previous Report Id: 0,    Next Report Id: 1638055646
  Version: 2.0
  State: CLOSED,      State Change Reason: RELOAD
  Start Time: Nov 28 12:02:09 2021 UTC,      End Time: Nov 30 22:02:13 2021 UTC
  Storage State: EXIST,  Storage State Change Reason: None
  Transaction ID: 0
  Transaction Message: <none>
  Report Size: 54880(54987)
<output truncated>

Table 11. show license tech support: Field Descriptions for Header "License Usage"
Field Name	Description
Interval:	This is a fixed measurement duration and is always 15 minutes.
Current Value:	Information about the current license count.
Current Report:	ID of the currently OPEN report for the license.
Previous:	ID of the last OPEN report for the license. This report will have state CLOSED now.

Field Name

Description

Total:

Total number of reports that the product instance has ever generated.

Note

This total does not refer to the total number of reports currently available on and being tracked by the product instance. For this you must sum up the Total Acknowledged Received: and Available to Report fields.

Purged:

The number of reports deleted due to a system resource limitation. This number includes RUM reports where the product instance no longer has tracking information.

Total Acknowledged Received:

The number of RUM reports acknowledged on this product instance.

Waiting for Ack:

The number of RUM reports waiting for an ACK. This is the total number of reports in an UNACK state, where the product instance still has tracking information.

Available to Report:

The number of RUM reports that are available to send to CSSM. This is the total number of reports in an OPEN or CLOSED state, where the product instance still has tracking information.

Collecting Data:

Number of reports where the product instance is currently collecting measurements.

Maximum Display:

Number of reports available for display in a show command's output.

In Storage:

Number of reports currently stored on the disk

MIA:

The number of reports missing.

Table 13. show license tech rum: Field Descriptions for Header "Smart Licensing Usage Report Detail"
Field Name	Description
Version:	Displays the format of the report during transmission. Starting with Cisco IOS XE Cupertino 17.7.1, RUM reports are stored in a new format that reduces processing time. This field indicates if the product instance is using the old format or the new format.
Storage State:	Indicates if a given report is currently in storage. In addition to the displaying the current storage state of the RUM report, with these possible values: EXIST, DELETED, PURGED, MISSING, if a "(1)" is displayed next to the label (`Storage State (1)`), this means the RUM report is in the older (pre-17.7.1 format) and will be processed accordingly. If the RUM report is in the new format, the field is displayed as `Storage State` - without any extra information.
Storage State Change Reason:	Displays the reason for the change in the storage state change. Not all state changes provide a reason. NONE: This means no reason was recorded for the the storage state change. PROCESSED: This means the RUM report was deleted after CISCO has processed the data. LIMIT_STORAGE: This means the RUM report was deleted because the product instance reached it's storage limit. LIMIT_TIME: This means the RUM report was deleted because the report reached the persisted time limit.
Transaction ID: Transaction Message:	If the transaction ID displays a correlation ID and an error status is displayed, the product instance displays the error code field in this section. If there are no errors, no data is displayed here.
Report Size	This field displays two numbers. The first number is the size of raw report for communication, in bytes. The second number is the disk space used for saving the report, also in bytes. The second number is displayed only if report is stored in the new format.

Examples

The following is sample output from the show license tech support command on a Cisco Catalyst 98000-CL Wireless Controller running software version Cisco IOS XE Cupertino 17.7.1:

Device# show license tech support 
Smart Licensing Tech Support info

Smart Licensing Status
======================

Smart Licensing is ENABLED

Export Authorization Key:
  Features Authorized:
    <none>

Utility:
  Status: DISABLED

Smart Licensing Using Policy:
  Status: ENABLED

Account Information:
  Smart Account: <none>
  Virtual Account: <none>

Data Privacy:
  Sending Hostname: yes
    Callhome hostname privacy: DISABLED
    Smart Licensing hostname privacy: DISABLED
  Version privacy: DISABLED
          
Transport:
  Type: Smart
  URL: https://smartreceiver.cisco.com/licservice/license
  Proxy:  
    Address: <empty>
    Port: <empty>
    Username: <empty>
    Password: <empty>
  Server Identity Check: True
  VRF: <empty>
          
Miscellaneous:
  Custom Id: <empty>
          
Policy:   
  Policy in use: Merged from multiple sources.
  Reporting ACK required: yes (CISCO default)
  Unenforced/Non-Export Perpetual Attributes:
    First report requirement (days): 365 (CISCO default)
    Reporting frequency (days): 0 (CISCO default)
    Report on change (days): 90 (CISCO default)
  Unenforced/Non-Export Subscription Attributes:
    First report requirement (days): 90 (CISCO default)
    Reporting frequency (days): 90 (CISCO default)
    Report on change (days): 90 (CISCO default)
  Enforced (Perpetual/Subscription) License Attributes:
    First report requirement (days): 0 (CISCO default)
    Reporting frequency (days): 0 (CISCO default)
    Report on change (days): 0 (CISCO default)
  Export (Perpetual/Subscription) License Attributes:
    First report requirement (days): 0 (CISCO default)
    Reporting frequency (days): 0 (CISCO default)
    Report on change (days): 0 (CISCO default)
          
Usage Reporting:
  Last ACK received: <none>
  Next ACK deadline: <none>
  Reporting push interval: 0 (no reporting) State(1) InPolicy(0)
  Next ACK push check: <none>
  Next report push: <none>
  Last report push: <none>
  Last report file write: <none>
          
License Usage
=============
Handle: 1 
  License: air-network-advantage
  Entitlement Tag: regid.2018-06.com.cisco.DNA_NWStack,1.0_e7244e71-3ad5-4608-8bf0-d12f67c80896
  Description: air-network-advantage
  Count: 0
  Version: 1.0
  Status: NOT IN USE(1)
  Status time: Oct 05 22:24:24 2021 UTC
  Request Time: None
  Export status: NOT RESTRICTED
  Feature Name: air-network-advantage
  Feature Description: air-network-advantage
  Enforcement type: NOT ENFORCED
  License type: Perpetual
  Measurements:
    ENTITLEMENT:
      Interval: 00:15:00
      Current Value: 0
      Current Report: 0       Previous: 0
  Soft Enforced: True
          
Handle: 2 
  License: air-dna-advantage
  Entitlement Tag: regid.2017-08.com.cisco.AIR-DNA-A,1.0_b6308627-3ab0-4a11-a3d9-586911a0d790
  Description: air-dna-advantage
  Count: 0
  Version: 1.0
  Status: NOT IN USE(1)
  Status time: Oct 05 22:24:24 2021 UTC
  Request Time: None
  Export status: NOT RESTRICTED
  Feature Name: air-dna-advantage
  Feature Description: air-dna-advantage
  Enforcement type: NOT ENFORCED
  License type: Subscription
  Measurements:
    ENTITLEMENT:
      Interval: 00:15:00
      Current Value: 0
      Current Report: 0       Previous: 0
  Soft Enforced: True
          
Product Information
===================
UDI: PID:C9800-CL-K9,SN:9KGIXIDOXFE
          
HA UDI List:
    Active:PID:C9800-CL-K9,SN:9KGIXIDOXFE
    Standby:PID:C9800-CL-K9,SN:9UBKZU955E4
          
Agent Version
=============
Smart Agent for Licensing: 5.3.14_rel/47
          
Upcoming Scheduled Jobs
=======================
Current time: Oct 06 00:38:46 2021 UTC
Daily: Oct 06 21:24:22 2021 UTC (20 hours, 45 minutes, 36 seconds remaining)
Authorization Renewal: Expired Not Rescheduled
Init Flag Check: Expired Not Rescheduled
Reservation configuration mismatch between nodes in HA mode: Expired Not Rescheduled
Start Utility Measurements: Oct 06 00:39:25 2021 UTC (39 seconds remaining)
Send Utility RUM reports: Oct 06 22:24:54 2021 UTC (21 hours, 46 minutes, 8 seconds remaining)
Save unreported RUM Reports: Oct 06 01:24:35 2021 UTC (45 minutes, 49 seconds remaining)
Data Synchronization: Expired Not Rescheduled
External Event: Expired Not Rescheduled
Operational Model: Expired Not Rescheduled
          
Communication Statistics:
=======================
Communication Level Allowed: INDIRECT
Overall State: Insufficient trust for direct communication
Trust Establishment:
  Attempts: Total=0, Success=0, Fail=0  Ongoing Failure: Overall=0 Communication=0
  Last Response: <none>
    Failure Reason: <none>
  Last Success Time: <none>
  Last Failure Time: <none>
Trust Acknowledgement:
  Attempts: Total=0, Success=0, Fail=0  Ongoing Failure: Overall=0 Communication=0
  Last Response: <none>
    Failure Reason: <none>
  Last Success Time: <none>
  Last Failure Time: <none>
Usage Reporting:
  Attempts: Total=0, Success=0, Fail=0  Ongoing Failure: Overall=0 Communication=0
  Last Response: <none>
    Failure Reason: <none>
  Last Success Time: <none>
  Last Failure Time: <none>
Result Polling:
  Attempts: Total=0, Success=0, Fail=0  Ongoing Failure: Overall=0 Communication=0
  Last Response: <none>
    Failure Reason: <none>
  Last Success Time: <none>
  Last Failure Time: <none>
Authorization Request:
  Attempts: Total=0, Success=0, Fail=0  Ongoing Failure: Overall=0 Communication=0
  Last Response: <none>
    Failure Reason: <none>
  Last Success Time: <none>
  Last Failure Time: <none>
Authorization Confirmation:
  Attempts: Total=0, Success=0, Fail=0  Ongoing Failure: Overall=0 Communication=0
  Last Response: <none>
    Failure Reason: <none>
  Last Success Time: <none>
  Last Failure Time: <none>
Authorization Return:
  Attempts: Total=0, Success=0, Fail=0  Ongoing Failure: Overall=0 Communication=0
  Last Response: <none>
    Failure Reason: <none>
  Last Success Time: <none>
  Last Failure Time: <none>
Trust Sync:
  Attempts: Total=0, Success=0, Fail=0  Ongoing Failure: Overall=0 Communication=0
  Last Response: <none>
    Failure Reason: <none>
  Last Success Time: <none>
  Last Failure Time: <none>
Hello Message:
  Attempts: Total=0, Success=0, Fail=0  Ongoing Failure: Overall=0 Communication=0
  Last Response: <none>
    Failure Reason: <none>
  Last Success Time: <none>
  Last Failure Time: <none>
          
License Certificates
====================
Production Cert: False
Not registered. No certificates installed
          
HA Info   
==========
RP Role: Active
Chassis Role: Active
Behavior Role: Active
RMF: True 
CF: True  
CF State: Stateless
Message Flow Allowed: False
          
Reservation Info
================ 
License reservation: DISABLED
          
Overall status:
  Active: PID:C9800-CL-K9,SN:9KGIXIDOXFE
      Reservation status: NOT INSTALLED
      Request code: <none>
      Last return code: <none>
      Last Confirmation code: <none>
      Reservation authorization code: <none>
  Standby: PID:C9800-CL-K9,SN:9UBKZU955E4
      Reservation status: NOT INSTALLED
      Request code: <none>
      Last return code: <none>
      Last Confirmation code: <none>
      Reservation authorization code: <none>
          
Specified license reservations:
          
Purchased Licenses:
  No Purchase Information Available
          
Usage Report Summary:
=====================
Total: 0,  Purged: 0(0)
Total Acknowledged Received: 0,  Waiting for Ack: 0(0)
Available to Report: 0  Collecting Data: 0  
Maximum Display: 0  In Storage: 0,  MIA: 0(0)
Report Module Status: Ready
          
Other Info
==========
Software ID: regid.2018-05.com.cisco.WLC_9500C,1.0_85665885-b865-4e32-8184-5510412fcb54
Agent State: authorized
TS enable: True
Transport: Smart
  Default URL: https://smartreceiver.cisco.com/licservice/license
Locale: en_US.UTF-8
Debug flags: 0x7
Privacy Send Hostname: True
Privacy Send IP: True
Build type:: Production
sizeof(char)  : 1
sizeof(int)   : 4
sizeof(long)  : 4
sizeof(char *): 8
sizeof(time_t): 4
sizeof(size_t): 8
Endian: Big
Write Erase Occurred: False
XOS version: 0.12.0.0
Config Persist Received: False
Message Version: 1.3
connect_info.name: <empty>
connect_info.version: <empty>
connect_info.additional: <empty>
connect_info.prod: False
connect_info.capabilities: <empty>
agent.capabilities: UTILITY, DLC, AppHA, MULTITIER, EXPORT_2, OK_TRY_AGAIN
Check Point Interface: True
Config Management Interface: False
License Map Interface: True
HA Interface: True
Trusted Store Interface: True
Platform Data Interface: True
Crypto Version 2 Interface: False
SAPluginMgmtInterfaceMutex: True
SAPluginMgmtIPDomainName: True
SmartTransportVRFSupport: True
SmartAgentClientWaitForServer: 2000
SmartAgentCmReTrySend: True
SmartAgentClientIsUnified: True
SmartAgentCmClient: True
SmartAgentClientName: UnifiedClient
builtInEncryption: True
enableOnInit: True
routingReadyByEvent: True
systemInitByEvent: True
SmartTransportServerIdCheck: True
SmartTransportProxySupport: True
SmartAgentPolicyDisplayFormat: 0
SmartAgentReportOnUpgrade: False
SmartAgentIndividualRUMEncrypt: 2
SmartAgentMaxRumMemory: 2
SmartAgentConcurrentThreadMax: 10
SmartAgentPolicyControllerModel: False
SmartAgentPolicyModel: True
SmartAgentFederalLicense: True
SmartAgentMultiTenant: False
attr365DayEvalSyslog: True
checkPointWriteOnly: False
SmartAgentDelayCertValidation: False
enableByDefault: False
conversionAutomatic: True
conversionAllowed: False
storageEncryptDisable: False
storageLoadUnencryptedDisable: False
TSPluginDisable: False
bypassUDICheck: False
loggingAddTStamp: False
loggingAddTid: True
HighAvailabilityOverrideEvent: UnknownPlatformEvent
platformIndependentOverrideEvent: UnknownPlatformEvent
platformOverrideEvent: UnknownPlatformEvent
WaitForHaRole: False
standbyIsHot: True
chkPtType: 2
delayCommInit: False
roleByEvent: True
maxTraceLength: 150
traceAlwaysOn: True
debugFlags: 0
Event log max size: 5120 KB
Event log current size: 3 KB
P:C9800-CL-K9,S:9KGIXIDOXFE: No Trust Data
P:C9800-CL-K9,S:9UBKZU955E4: No Trust Data
Overall Trust: No ID
Clock sync-ed with NTP: True
          
Platform Provided Mapping Table
===============================
  C9800-CL-K9: Total licenses found: 5
Enforced Licenses:
  P:C9800-CL-K9,S:9KGIXIDOXFE:
    No PD enforced licenses
  P:C9800-CL-K9,S:9UBKZU955E4:
    No PD enforced licenses

Example (Smart Licensing Using Policy)

The following is sample output from the show license tech support command.

Device# show license tech support 

Smart Licensing Tech Support info

Smart Licensing Status
======================

Smart Licensing is ENABLED
License Reservation is ENABLED

Registration:
  Status: REGISTERED - SPECIFIC LICENSE RESERVATION
  Export-Controlled Functionality: ALLOWED
  Initial Registration: SUCCEEDED on Nov 02 03:16:01 2020 IST

License Authorization: 
  Status: AUTHORIZED - RESERVED on Nov 02 03:16:01 2020 IST

Export Authorization Key:
  Features Authorized:
    <none>

Utility:
  Status: DISABLED

Data Privacy:
  Sending Hostname: yes
    Callhome hostname privacy: DISABLED
    Smart Licensing hostname privacy: DISABLED
  Version privacy: DISABLED

Transport:
  Type: Smart
  URL: https://smartreceiver.cisco.com/licservice/license

Evaluation Period:
  Evaluation Mode: Not In Use
  Evaluation Period Remaining: 89 days, 23 hours, 42 minutes, 47 seconds

License Usage
=============
Handle: 1
  License: AP Perpetual Networkstack Advantage
  Entitlement tag: regid.2018-06.com.cisco.DNA_NWStack,1.0_e7244e71-3ad5-4608-8bf0-d12f67c80896
  Description: AP Perpetual Network Stack entitled with DNA-A
  Count: 1
  Version: 1.0
  Status: AUTHORIZED(3)
  Status time: Nov 02 03:16:01 2020 IST
  Request Time: Nov 02 02:55:34 2020 IST
  Export status: NOT RESTRICTED
  Soft Enforced: True

Handle: 2
  License: Aironet DNA Advantage Term Licenses
  Entitlement tag: regid.2017-08.com.cisco.AIR-DNA-A,1.0_b6308627-3ab0-4a11-a3d9-586911a0d790
  Description: DNA Advantage for Wireless
  Count: 1
  Version: 1.0
  Status: AUTHORIZED(3)
  Status time: Nov 02 03:16:01 2020 IST
  Request Time: Nov 02 02:55:34 2020 IST
  Export status: NOT RESTRICTED
  Soft Enforced: True

Product Information
===================
UDI: PID:C9800-CL-K9,SN:93BBAH93MGS

HA UDI List:
    Active:PID:C9800-CL-K9,SN:93BBAH93MGS
    Standby:PID:C9800-CL-K9,SN:9XECPSUU4XN

Agent Version
=============
Smart Agent for Licensing: 4.8.7_rel/52

Upcoming Scheduled Jobs
=======================
Current time: Nov 02 03:17:23 2020 IST
Daily: Nov 03 02:47:04 2020 IST (23 hours, 29 minutes, 41 seconds remaining)
Certificate Renewal: Not Available
Certificate Expiration Check: Not Available
Authorization Renewal: Not Available
Authorization Expiration Check: Not Available
Init Flag Check: Not Available
Evaluation Expiration Check: Not Available
Ack Expiration Check: Not Available
Evaluation Expiration Warning: Not Available
IdCert Expiration Warning: Not Available
Reservation request in progress warning: Not Available
Reservation configuration mismatch between nodes in HA mode: Nov 09 03:16:30 2020 IST (6 days, 23 hours, 59 minutes, 7 seconds remaining)
Endpoint Report Request: Not Available

License Certificates
====================
Production Cert: True
Not registered. No certificates installed

HA Info
==========
RP Role: Active
Chassis Role: Active
Behavior Role: Active
RMF: True
CF: True
CF State: Stateless
Message Flow Allowed: False

Reservation Info
================ 
License reservation: ENABLED

Overall status:
  Active: PID:C9800-CL-K9,SN:93BBAH93MGS
      Reservation status: SPECIFIC INSTALLED on Nov 02 03:16:01 2020 IST
      Export-Controlled Functionality: ALLOWED
      Request code: <none>
      Last return code: <none>
      Last Confirmation code: 102fc949
      Reservation authorization code: <specificPLR><authorizationCode><flag>A</flag><version>C</version><piid>ebac0ce9-b30b-4187-8ac7-4c22a157b9b1</piid><timestamp>1604295380710</timestamp><entitlements><entitlement><tag>regid.2017-08.com.cisco.AIR-DNA-A,1.0_b6308627-3ab0-4a11-a3d9-586911a0d790</tag><count>5</count><startDate>2020-Oct-14 UTC</startDate><endDate>2021-Apr-12 UTC</endDate><licenseType>TERM</licenseType><displayName>Aironet DNA Advantage Term Licenses</displayName><tagDescription>DNA Advantage for Wireless</tagDescription><subscriptionID></subscriptionID></entitlement><entitlement><tag>regid.2017-08.com.cisco.AIR-DNA-A,1.0_b6308627-3ab0-4a11-a3d9-586911a0d790</tag><count>5</count><startDate>2020-Jun-18 UTC</startDate><endDate>2020-Dec-15 UTC</endDate><licenseType>TERM</licenseType><displayName>Aironet DNA Advantage Term Licenses</displayName><tagDescription>DNA Advantage for Wireless</tagDescription><subscriptionID></subscriptionID></entitlement><entitlement><tag>regid.2018-06.com.cisco.DNA_NWStack,1.0_e7244e71-3ad5-4608-8bf0-d12f67c80896</tag><count>5</count><startDate>2020-Oct-14 UTC</startDate><endDate>2021-Apr-12 UTC</endDate><licenseType>TERM</licenseType><displayName>AP Perpetual Networkstack Advantage</displayName><tagDescription>AP Perpetual Network Stack entitled with DNA-A</tagDescription><subscriptionID></subscriptionID></entitlement><entitlement><tag>regid.2018-06.com.cisco.DNA_NWStack,1.0_e7244e71-3ad5-4608-8bf0-d12f67c80896</tag><count>5</count><startDate>2020-Jun-18 UTC</startDate><endDate>2020-Dec-15 UTC</endDate><licenseType>TERM</licenseType><displayName>AP Perpetual Networkstack Advantage</displayName><tagDescription>AP Perpetual Network Stack entitled with DNA-A</tagDescription><subscriptionID></subscriptionID></entitlement></entitlements></authorizationCode><signature>MEUCIQCB14HM4Yd6g+ETU/AE0Vpn2QBsvDGtX9Yl6XI4fUmRAgIgJ7P84t1LVEStDlhxT/EMgC9mK1harPewk/zQDpfQ2+c=</signature><udi>P:C9800-CL-K9,S:93BBAH93MGS</udi></specificPLR>
  Standby: PID:C9800-CL-K9,SN:9XECPSUU4XN
      Reservation status: SPECIFIC INSTALLED on Nov 02 03:15:45 2020 IST
      Export-Controlled Functionality: ALLOWED
      Request code: <none>
      Last return code: <none>
      Last Confirmation code: ad4382fe
      Reservation authorization code: <specificPLR><authorizationCode><flag>A</flag><version>C</version><piid>48db0211-b970-4a70-800e-17943e90d536</piid><timestamp>1604295428976</timestamp><entitlements><entitlement><tag>regid.2018-06.com.cisco.DNA_NWStack,1.0_e7244e71-3ad5-4608-8bf0-d12f67c80896</tag><count>10</count><startDate>2020-Oct-14 UTC</startDate><endDate>2021-Apr-12 UTC</endDate><licenseType>TERM</licenseType><displayName>AP Perpetual Networkstack Advantage</displayName><tagDescription>AP Perpetual Network Stack entitled with DNA-A</tagDescription><subscriptionID></subscriptionID></entitlement><entitlement><tag>regid.2017-08.com.cisco.AIR-DNA-A,1.0_b6308627-3ab0-4a11-a3d9-586911a0d790</tag><count>10</count><startDate>2020-Oct-14 UTC</startDate><endDate>2021-Apr-12 UTC</endDate><licenseType>TERM</licenseType><displayName>Aironet DNA Advantage Term Licenses</displayName><tagDescription>DNA Advantage for Wireless</tagDescription><subscriptionID></subscriptionID></entitlement></entitlements></authorizationCode><signature>MEUCIQCoAMojN184RkvFwSN4h/hd9wu9GcIQYW/fitsvl6mrUAIgNIrNfpYq/TSq+3FfIQtLxi+NGPg//U8q3dTjQpKHPmQ=</signature><udi>P:C9800-CL-K9,S:9XECPSUU4XN</udi></specificPLR>

Specified license reservations:
  Aironet DNA Advantage Term Licenses (AIR-DNA-A):
    Description: DNA Advantage for Wireless
    Total reserved count: 20
    Term information:
      Active: PID:C9800-CL-K9,SN:93BBAH93MGS
        License type: TERM
          Start Date: 2020-OCT-14 UTC
          End Date: 2021-APR-12 UTC
          Term Count: 5
          Subscription ID: <none>
        License type: TERM
          Start Date: 2020-JUN-18 UTC
          End Date: 2020-DEC-15 UTC
          Term Count: 5
          Subscription ID: <none>
      Standby: PID:C9800-CL-K9,SN:9XECPSUU4XN
        License type: TERM
          Start Date: 2020-OCT-14 UTC
          End Date: 2021-APR-12 UTC
          Term Count: 10
          Subscription ID: <none>
  AP Perpetual Networkstack Advantage (DNA_NWStack):
    Description: AP Perpetual Network Stack entitled with DNA-A
    Total reserved count: 20
    Term information:
      Active: PID:C9800-CL-K9,SN:93BBAH93MGS
        License type: TERM
          Start Date: 2020-OCT-14 UTC
          End Date: 2021-APR-12 UTC
          Term Count: 5
          Subscription ID: <none>
        License type: TERM
          Start Date: 2020-JUN-18 UTC
          End Date: 2020-DEC-15 UTC
          Term Count: 5
          Subscription ID: <none>
      Standby: PID:C9800-CL-K9,SN:9XECPSUU4XN
        License type: TERM
          Start Date: 2020-OCT-14 UTC
          End Date: 2021-APR-12 UTC
          Term Count: 10
          Subscription ID: <none>

Other Info
==========
Software ID: regid.2018-05.com.cisco.WLC_9500C,1.0_85665885-b865-4e32-8184-5510412fcb54
Agent State: authorized
TS enable: True
Transport: Smart
  Default URL: https://smartreceiver.cisco.com/licservice/license
Locale: en_US.UTF-8
Debug flags: 0x7
Privacy Send Hostname: True
Privacy Send IP: True
Build type:: Production
sizeof(char)  : 1
sizeof(int)   : 4
sizeof(long)  : 4
sizeof(char *): 8
sizeof(time_t): 4
sizeof(size_t): 8
Endian: Big
Write Erase Occurred: False
XOS version: 0.12.0.0
Config Persist Received: False
Message Version: 1.3
connect_info.name: <empty>
connect_info.version: <empty>
connect_info.additional: <empty>
connect_info.prod: False
connect_info.capabilities: <empty>
agent.capabilities: UTILITY, DLC, AppHA, MULTITIER, EXPORT_2, OK_TRY_AGAIN
SmartAgentClientWaitForServer: 2000
SmartAgentCmReTrySend: True
SmartAgentClientIsUnified: True
SmartAgentCmClient: True
SmartAgentClientName: UnifiedClient
builtInEncryption: True
enableOnInit: True
routingReadyByEvent: True
systemInitByEvent: True
SmartAgentFederalLicense: True
SmartAgent_Crypto_Exit_CB: 0x55B353357A20
SmartAgent_Crypto_Start_CB: 0x55B353357A10
SmartAgentMultiTenant: False
attr365DayEvalSyslog: True
checkPointWriteOnly: False
SmartAgentDelayCertValidation: False
enableByDefault: False
conversionAutomatic: True
conversionAllowed: False
storageEncryptDisable: False
storageLoadUnencryptedDisable: False
TSPluginDisable: False
bypassUDICheck: False
loggingAddTStamp: False
loggingAddTid: True
platformOverrideEvent: UnknownPlatformEvent
WaitForHaRole: False
standbyIsHot: True
chkPtType: 2
delayCommInit: False
roleByEvent: True
maxTraceLength: 150
traceAlwaysOn: True
debugFlags: 0
Event log max size: 5120 KB
Event log current size: 21 KB

Platform Provided Mapping Table
===============================
<empty>

show license udi

To display Unique Device Identifier (UDI) information for a product instance, enter the show license udi command in privileged EXEC mode. In a High Availability set-up, the output displays UDI information for all connected product instances.

show license udi

Syntax Description


This command has no keywords or arguments

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.
Cisco IOS XE Amsterdam 17.3.2a	This command continues to be available with the introduction of Smart Licensing Using Policy.

Usage Guidelines

Smart Licensing Using Policy: If the software version on the device (also referred to as a product instance) is Cisco IOS XE Amsterdam 17.3.2a or a later release, command output displays fields pertinent to Smart Licensing Using Policy.

Smart Licensing: If the software version on the device is Cisco IOS XE Amsterdam 17.3.1 or an earlier release, command output displays fields pertinent to Smart Licensing.

Examples

show license udi with Standalone Product Instance

show license udi with Active and Standby

show license udi with Standalone Product Instance

The following is sample output from the show license udi command on a standalone product instance.

Device# show license udi

UDI: PID:C9800-L-F-K9,SN:FCW2323W016

show license udi with Active and Standby

The following is sample output from the show license udi command in a High Availability set-up where an active and a standby product instances exist. UDI information is displayed for both.

Device# show license udi

UDI: PID:C9800-CL-K9,SN:93BBAH93MGS

HA UDI List:
    Active:PID:C9800-CL-K9,SN:93BBAH93MGS
    Standby:PID:C9800-CL-K9,SN:9XECPSUU4XN

show license usage

To display license usage information such as status, a count of licenses being used, and enforcement type, enter the show license usage command in privileged EXEC mode.

show license usage

Syntax Description


This command has no keywords or arguments

Command Modes

Privileged EXEC

Command History


Release	Modification
This command was introduced in a release earlier than Cisco IOS XE Amsterdam 17.3.2	This command was introduced.
Cisco IOS XE Amsterdam 17.3.2a	Command output was updated to reflect new fields that are applicable to Smart Licensing Using Policy. This includes the `Status`, `Enforcement type` fields. Command output was also updated to remove reservation related information, authorization status information, and export status information.

Usage Guidelines

Smart Licensing Using Policy: If the software version on the device (also referred to as a product instance) is Cisco IOS XE Amsterdam 17.3.2a or a later release, command output displays fields pertinent to Smart Licensing Using Policy.

Smart Licensing: If the software version on the device is Cisco IOS XE Amsterdam 17.3.1 or an earlier release, command output displays fields pertinent to Smart Licensing.

Examples

See Table 1 for information about fields shown in the display.

show license usage with unenforced licenses (Smart Licensing Using Policy)

show license usage with unenforced SLR licenses (Smart Licensing Using Policy)

Table 14. show license usage Field Descriptions
Field	Description
License Authorization: Status:	Displays overall authorization status.
():	Name of the license as in CSSM. If this license is one that requires an authorization code, the name of the license comes from the code.
Description	Description of the license as in CSSM.
Count	License count. If the license is not in-use, the count is reflected as zero.
Version	Version.
Status	License status can be one of the following In-Use: Valid license, and in-use. Not In-Use Not Authorized: Means that the license requires installation of SLAC before use. For more information, see
Export Status:	Indicates if this license is export-controlled or not. Accordingly, one of the following statuses is displayed: RESTRICTED - ALLOWED RESTRICTED - NOT ALLOWED NOT RESTRICTED
Feature name	Name of the feature that uses this license.
Feature Description:	Description of the feature that uses this license.
Utility Subscription id:	ID Not applicable, because the corresponding confiuration option is not supported.
Enforcement type	Enforcement type status for the license. This may be one of the following: ENFORCED NOT ENFORCED EXPORT RESTRICTED - ALLOWED EXPORT RESTRICTED - NOT ALLOWED For more information about enforcement types, see <link tbd>

show license usage with unenforced licenses (Smart Licensing Using Policy)

The following is sample output of the show license usage command. Unenforced licenses are in-use here.

Device# show license usage 

License Authorization: 
  Status: Not Applicable

air-network-essentials (DNA_NWSTACK_E):
  Description: air-network-essentials
  Count: 1
  Version: 1.0
  Status: IN USE
  Export status: NOT RESTRICTED
  Feature Name: air-network-essentials
  Feature Description: air-network-essentials
  Enforcement type: NOT ENFORCED
  License type: Perpetual

air-dna-essentials (AIR-DNA-E):
  Description: air-dna-essentials
  Count: 1
  Version: 1.0
  Status: IN USE
  Export status: NOT RESTRICTED
  Feature Name: air-dna-essentials
  Feature Description: air-dna-essentials
  Enforcement type: NOT ENFORCED
  License type: Perpetual

show license usage with unenforced SLR licenses (Smart Licensing Using Policy)

The following is sample output of the show license usage command. Migrated SLR licenses are in-use here:

Device# show license usage

air-network-advantage (DNA_NWStack):
  Description: air-network-advantage
  Count: 1
  Version: 1.0
  Status: IN USE
  Export status: NOT RESTRICTED
  Feature Name: air-network-advantage
  Feature Description: air-network-advantage
  Enforcement type: NOT ENFORCED
  License type: Perpetual
  Reservation: 
    Reservation status: SPECIFIC INSTALLED
    Total reserved count: 20

air-dna-advantage (AIR-DNA-A):
  Description: air-dna-advantage
  Count: 1
  Version: 1.0
  Status: IN USE
  Export status: NOT RESTRICTED
  Feature Name: air-dna-advantage
  Feature Description: air-dna-advantage
  Enforcement type: NOT ENFORCED
  License type: Perpetual
  Reservation: 
    Reservation status: SPECIFIC INSTALLED
    Total reserved count: 20

show platform software rif-mgr chassis active R0 resource-status

To verify the Redundancy Port Interface (RIF) resource status in an active instance, use the show platform software rif-mgr chassis active R0 resource-status command.

show platform software rif-mgr chassis active R0 resource-status

Syntax Description


rif-mgr	Displays information about the RIF manager.
chassis	Displays information about the chassis.
active	Specifies the Active instance.
R0	Specifies the Route-Processor slot 0.
resource-status	Displays the resource status.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Usage Guidelines

The RIF resource status displays the RP status, RMI status, Current Chassis State, and Peer Chassis State.

Example

The following example shows how to verify the RIF resource status in active instance:

Device# show platform software rif-mgr chassis active R0 resource-status
RIF Resource Status

    RP Status             : Up
    RMI Status            : Up
    Current Chassis State : Active
    Peer Chassis State    : Standby

show platform software rif-mgr chassis standby R0 resource-status

To verify the Redundancy Port Interface (RIF) resource status in a standby instance, use the show platform software rif-mgr chassis standby R0 resource-status command.

show platform software rif-mgr chassis standby R0 resource-status

Syntax Description


rif-mgr	Displays information about the RIF manager.
chassis	Displays information about the chassis.
standby	Specifies the Standby instance.
R0	Specifies the Route-Processor slot 0.
resource-status	Displays the resource status.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Usage Guidelines

The RIF resource status displays the RP status, RMI status, Current Chassis State, and Peer Chassis State.

Example

The following example shows how to verify the RIF resource status in standby instance:

Device# show platform software rif-mgr chassis standby R0 resource-status
RIF Resource Status

    RP Status             : Up
    RMI Status            : Up
    Current Chassis State : Standby
    Peer Chassis State    : Active

show platform software rif-mgr chassis active R0 rmi-connection-details

To verify the RMI link re-establishment count and the time since it is Up or Down in an active instance, use the show platform software rif-mgr chassis active R0 rmi-connection-details command.

show platform software rif-mgr chassis active R0 rmi-connection-details

Syntax Description


rif-mgr	Displays information about the RIF manager.
chassis	Displays information about the chassis.
active	Specifies the Active instance.
R0	Specifies the Route-Processor slot 0.
rmi-connection-details	Displays the RMI connection details.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Examples

The following example shows how to verify the RMI link re-establishment count and the time since it is Up in an active instance:

Device# show platform software rif-mgr chassis active R0 rmi-connection-details
RMI Connection Details
    RMI Link re-establish count : 2
    RMI Link Uptime             : 21 hours 8 minutes 43 seconds
    RMI Link Upsince            : 08/05/2021 13:46:01

The following example shows how to verify the RMI link re-establishment count and the time since it is Down in an active instance:

Device# show platform software rif-mgr chassis active R0 rmi-connection-details
RMI Connection Details
    RMI Link re-establish count : 1
    RMI Link Downtime           : 28 seconds
    RMI Link Downsince          : 07/16/2021 03:19:11

show platform software rif-mgr chassis standby R0 rmi-connection-details

To verify the RMI link re-establishment count and the time since it is Up or Down in a standby instance, use the show platform software rif-mgr chassis standby R0 rmi-connection-details command.

show platform software rif-mgr chassis standby R0 rmi-connection-details

Syntax Description


rif-mgr	Displays information about the RIF manager.
chassis	Displays information about the chassis.
standby	Specifies the Standby instance.
R0	Specifies the Route-Processor slot 0.
rmi-connection-details	Displays the RMI connection details.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Examples

The following example shows how to verify the RMI link re-establishment count and the time since it is Up in a standby instance:

Device# show platform software rif-mgr chassis standby R0 rmi-connection-details
RMI Connection Details
    RMI Link re-establish count : 1
    RMI Link Uptime             : 1 hour 39 minute 9 seconds
    RMI Link Upsince            : 07/16/2021 01:31:41

The following example shows how to verify the RMI link re-establishment count and the time since it is Down in a standby instance:

Device# show platform software rif-mgr chassis standby R0 rmi-connection-details
RMI Connection Details
    RMI Link re-establish count : 1
    RMI Link Downtime           : 22 seconds
    RMI Link Downsince          : 07/16/2021 03:19:17

show platform software rif-mgr chassis active R0 rp-connection-details

To verify the RP link re-establishment count and the time since it is UP or Down in an active instance, use the show platform software rif-mgr chassis active R0 rp-connection-details command.

show platform software rif-mgr chassis active R0 rp-connection-details

Syntax Description


rif-mgr	Displays information about the RIF manager.
chassis	Displays information about the chassis.
active	Specifies the Active instance.
R0	Specifies the Route-Processor slot 0.
rp-connection-details	Displays the RP connection details.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Examples

The following example shows how to verify the RP link re-establishment count and the time since it is UP for days in an active instance:

Device# show platform software rif-mgr chassis active R0 rp-connection-details
RP Connection Details
    RP Connection Uptime  : 12 days 17 hours 1 minute 39 seconds
    RP Connection Upsince : 07/03/2021 07:06:20

The following example shows how to verify the RP link re-establishment count and the time since it is Down in an active instance:

Device# show platform software rif-mgr chassis active R0 rp-connection-details
RP Connection Details
    RP Connection Downtime     : 4 seconds
    RP Connection Downsince    : 07/16/2021 03:33:04

show platform software rif-mgr chassis standby R0 rp-connection-details

To verify the RP link re-establishment count and the time since it is UP or Down in a standby instance, use the show platform software rif-mgr chassis standby R0 rp-connection-details command.

show platform software rif-mgr chassis standby R0 rp-connection-details

Syntax Description


rif-mgr	Displays information about the RIF manager.
chassis	Displays information about the chassis.
standby	Specifies the Standby instance.
R0	Specifies the Route-Processor slot 0.
rp-connection-details	Displays the RP connection details.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Examples

The following example shows how to verify the RP link re-establishment count and the time since it is UP in a standby instance:

Device# show platform software rif-mgr chassis standby R0 rp-connection-details
RP Connection Details
    RP Connection Uptime  : 12 days 17 hours 2 minutes 1 second
    RP Connection Upsince : 07/03/2021 07:05:58

The following example shows how to verify the RP link re-establishment count and the time since it is Down in a standby instance:

Device# show platform software rif-mgr chassis standby R0 rp-connection-details
RP Connection Details
    RP Connection Downtime    : 22 seconds
    RP Connection Downsince   : 07/16/2021 03:19:17

show platform software rif-mgr chassis active R0 rif-stk-internal-stats

To verify the RIF and stack manager internal statistics in an active instance, use the show platform software rif-mgr chassis active R0 rif-stk-internal-stats command.

show platform software rif-mgr chassis active R0 rif-stk-internal-stats

Syntax Description


rif-mgr	Displays information about the RIF manager.
chassis	Displays information about the chassis.
active	Specifies the Active instance.
R0	Specifies the Route-Processor slot 0.
rif-stk-internal-stats	Displays the RIF and stack manager internal statistics.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Example

The following example shows how to verify the RIF and stack manager internal statistics in an active instance:

Device# show platform software rif-mgr chassis active R0 rif-stk-internal-stats
RIF Stack Manager internal stats

    Stack-mgr reported RP down            : False
    DAD link status reported to Stack-Mgr : True

show platform software rif-mgr chassis standby R0 rif-stk-internal-stats

To verify the RIF and stack manager internal statistics in a standby instance, use the show platform software rif-mgr chassis standby R0 rif-stk-internal-stats command.

show platform software rif-mgr chassis standby R0 rif-stk-internal-stats

Syntax Description


rif-mgr	Displays information about the RIF manager.
chassis	Displays information about the chassis.
standby	Specifies the Standby instance.
R0	Specifies the Route-Processor slot 0.
rif-stk-internal-stats	Displays the RIF and stack manager internal statistics.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Example

The following example shows how to verify the RIF and stack manager internal statistics in a standby instance:

Device# show platform software rif-mgr chassis standby R0 rif-stk-internal-stats
RIF Stack Manager internal stats

    Stack-mgr reported RP down            : False
    DAD link status reported to Stack-Mgr : True

show platform software rif-mgr chassis active R0 lmp-statistics

To verify the number of packets sent or received for each type in an active instance, use the show platform software rif-mgr chassis active R0 lmp-statistics command.

show platform software rif-mgr chassis active R0 lmp-statistics

Syntax Description


rif-mgr	Displays information about the RIF manager.
chassis	Displays information about the chassis.
active	Specifies the Active instance.
R0	Specifies the Route-Processor slot 0.
lmp-statistics	Displays the LMP statistics.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Example

The following example shows how to verify the number of packets sent or received for each type in an active instance:

Device# show platform software rif-mgr chassis active R0 lmp-statistics
LMP Statistics

Info Type Sent                    : 6
Solicit Info Type Sent            : 0
Unsolicit Info Type Sent          : 6
Reload Type Sent                  : 0
Recovery Type Sent                : 1 
Gateway Info Type Sent            : 0
Enquiry Type Sent                 : 0
Solicit Enquiry Type Sent         : 0
Unsolicit Enquiry Type Sent       : 0 

Info Type Received                : 5
Solicit Info Type Received        : 2
Unsolicit Info Type Received      : 3
Reload Type Received              : 0
Recovery Type Received            : 0
Gateway Info Type Received        : 4
Enquiry Type Received             : 0
Solicit Enquiry Type Received     : 0
Unsolicit Enquiry Type Received   : 0

show platform software rif-mgr chassis standby R0 lmp-statistics

To verify the number of packets sent or received for each type in a standby instance, use the show platform software rif-mgr chassis standby R0 lmp-statistics command.

show platform software rif-mgr chassis standby R0 lmp-statistics

Syntax Description


rif-mgr	Displays information about the RIF manager.
chassis	Displays information about the chassis.
standby	Specifies the Standby instance.
R0	Specifies the Route-Processor slot 0.
lmp-statistics	Displays the LMP statistics.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Example

The following example shows how to verify the number of packets sent or received for each type in a standby instance:

Device# show platform software rif-mgr chassis standby R0 lmp-statistics
LMP Statistics

Info Type Sent                   : 6
Solicit Info Type Sent           : 0
Unsolicit Info Type Sent         : 6
Reload Type Sent                 : 0
Recovery Type Sent               : 0
Gateway Info Type Sent           : 4
Enquiry Type Sent                : 0
Solicit Enquiry Type Sent        : 0
Unsolicit Enquiry Type Sent      : 0

Info Type Received               : 5
Solicit Info Type Received       : 3
Unsolicit Info Type Received     : 2
Reload Type Received             : 0
Recovery Type Received           : 1
Gateway Info Type Received       : 0
Enquiry Type Received            : 0
Solicit Enquiry Type Received    : 0
Unsolicit Enquiry Type Received  : 0

show platform software sl-infra

To display troubleshooting information and for debugging, enter the show platform software sl-infra command in privileged EXEC mode. The output of this command is used by the technical support team, for troubleshooting and debugging.

show platform software sl-infra { all | current | debug | stored }

Syntax Description


all	Displays current, debugging, and stored information.
current	Displays current license-related information.
debug	Enables debugging
stored	Displays information that is stored on the product instance.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.3.2a	This command was introduced.

Usage Guidelines

When you encounter an error message that you are not able to resolve, along with a copy of the message that appears on the console or in the system log, provide your Cisco technical support representative with sample output of these commands: show license tech support , show license history message , and the show platform software sl-infra all privileged EXEC commands.

show platform software tls client summary

To view the TLS client summary details, use the show platform software tls client summary command.

show platform software tls client summary

Syntax Description


This command has no keywords or arguments.

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Examples

This example shows how to view the TLS client summary details:


Device # show platform software tls client summary


Name     ID     Gateway   Port   Auth     Trustpoint   DPD Time Rekey Time  Retry Time
---------------------------------------------------------------------------------------
fqdn     0                8443   PSK       N/A           60       300         20

show platform software client detail

To display a summary of TLS client session detail, session statistics, tunnel statistics, and DNS counters, use the show platform software client detail command.

show platform software client detail

Syntax Description


This command has no keywords or arguments.

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Examples

This example shows how to view the TLS client summary details:


Device # show platform software client detail

TLS Client           : Session Detail
Session Name         : fqdn
FQDN resolved IP     : 10.194.234.149
ID                   : 0
Created              : 04/20/21 00:36:42
Updated              : 04/22/21 05:56:03
State                : Up (Rekey)
Up Time              : 04/21/21 20:30:21 ( 9 hours 25 minutes 45 seconds )
Down Time            : 04/21/21 20:30:01
Rekey Time           : 04/22/21 05:55:51 ( 15 seconds )

TLS Session Statistics

Up Notifications     : 3
Down Notifications   : 2
Rekey Notifications  : 636
DP State Updates     : 0
DPD Cleanups         : 0

Packets From     Packets To  Packet Errors To     Bytes From           Bytes To
---------------------------------------------------------------------------------
  BinOS              80           0                                         0
  IOSd                0           0                    0                    0                           
  TLS Client          0           0                    0                    0                           

TLS Tunnel Statistics
Type            Tx Packets      Rx Packets
-------------------------------------------
  Total             0               80
  CSTP Ctrl      3836             3836
  CSTP Data        80                0

Type            Requests         Responses
--------------------------------------------
CSTP Cfg          639                  639
CSTP DPD         3197                 3197

Invalid CSTP Rx          : 0
Injected Packet Success  : 0
Injected Packet Failed   : 0
Consumed Packets         : 0

TLS Tunnel DNS Counters
DNS Resolve Request Success Count    : 641
DNS Resolve Request Failure Count    :  0
DNS Resolve Success Count            : 639
DNS Resolve Failure Count            :  2

show platform software tls statistics

To view the TLS client global statistic details, use the show platform software tls statistics command.

show platform software tls statistics

Syntax Description


This command has no keywords or arguments.

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Examples

This example shows how to view the TLS client summary details:


Device # show platform software tls statistics

TLS Client - Global Statistics
Session Statistics
Up/Down           : 5/2
Rekeys            : 636
DP Updates        :   0
DPD Cleanups      :   0

Packets From    Packets To   Packet Errors To     Bytes From   Bytes To
----------------------------------------------------------------------
BinOS              85             0                  0             0
IOSd 0             0              0                  0             0
TLS Client  0      0                                 0             0

Tunnel Statistics
SSL Handshake Init/Done     : 641/641
TCP Connection Req/Done     : 641/641

Tunnel Packets
Rx/Tx                       : 85/0
Injected / Failed           : 0/0
Consumed                    :  0

CSTP Packets
Control Rx/Tx               : 3839 / 3839
Data Rx/Tx                  : 0 / 85
Config Req/Resp             : 641 / 641
DPD Req/Resp                : 3198 / 3198
Invalid Rx                  : 0

FQDN Counters
Req/Resp/Success            : 0/0/0

NAT Counters
Transalte In/Out            : 0/0
Ignore    In/Out            : 0/0
Failed                      : 0
Invalid                     : 0
No Entry                    : 0
Unsupported                 : 0

Internal Counters
Type           Allocated            Freed
-------------------------------------------------
EV              1299                 1295
Tunnel           5                     4
Conn            643                   642
Sess             3                     2

Config Message Related Counters
Type               Success              Failed
-------------------------------------------------
Create                3                    0
Delete                2                    0

show platform software tls session summary

To view the tls client session summary, use the show platform software tls session summary command.

show platform software tls session summary

Syntax Description


This command has no keywords or arguments.

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Examples

This example shows how to view the TLS client summary details:


Device # show platform software tls session summary

TLS Client - Session Summary
Name     ID      Created            State    Since               Elapsed
----------------------------------------------------------------------------------------------
fqdn     0      04/20/21 00:36:42    Up     04/21/21 20:30:21   9 hours 26 minutes 44 seconds

show lisp site detail

To see detailed Locator ID Separation Protocol (LISP) site information on a map server, use the show lisp site detail command.

show lisp site detail [eid-table {default | vlan vlan-id | vrf vrf-name } | instance-id id-number | internal {eid-table {default | vlan vlan-id | vrf vrf-name} | instance-id id-number}]

Syntax Description


eid-table	Option to enter the EID table.
default	Shows the information for the default VRF.
vlan `vlan-id`	Enter the VLAN information.
vrf `vrf-name`	Enter the VRF name.
instance-id `id-number`	Enter the EID instance ID.
internal	Shows the site's detailed internal information.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see detailed Locator ID Separation Protocol (LISP) site information on a map server:

Device# show lisp site detail

show logging profile wireless end timestamp

To specify log filtering end location timestamp for filtering, use the show logging profile wireless end timestamp command.

show logging profile wireless end timestamp time-stamp

Syntax Description


`time-stamp`	Time to end the filtering. For example, 2017/02/10 14:41:50.849.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

Ensure that you enable internal keyword using the show logging profile wireless internal command to get the trace output.

Examples

The following example shows how to specify log filtering end location timestamp for filtering:

Device# show logging profile wireless end timestamp 2017/02/10 14:41:50.849

show logging profile wireless filter

To specify filter for logs, use the show logging profile wireless filter command.

show logging profile wireless filter { ipv4| mac| string| uuid}

Syntax Description


ipv4	Selects logs with specific IP address app context.
mac	Selects logs with specific MAC app context.
string	Selects logs with specific string app context.
uuid	Selects logs with specific Universally Unique Identifier (UUID) app context.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

Ensure that you enable internal keyword using the show logging profile wireless internal command to get the trace output.

Without the internal keyword, only customer curated logs are displayed.

Examples

The following example shows how to specify filter for logs:

Device# show logging profile wireless filter ipv4 10.10.11.1

show logging profile wireless fru

To specify field-replaceable unit (FRU) specific commands, use the show logging profile wireless fru command.

show logging profile wireless fru {0 {reverse | to-file}| chassis} { 0 { reverse| to-file} | chassis}

Syntax Description


0	SPA-Inter-Processor slot 0.
reverse	Shows logs in reverse chronological order.
to-file	Decodes files stored in disk and write output to file.
chassis	Chassis name.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

Ensure that you enable internal keyword using the show logging profile wireless internal command to get the trace output.

Without the internal keyword, only customer curated logs are displayed.

Examples

The following example shows how to specify FRU specific commands:

Device# show logging profile wireless fru 0

show logging profile wireless internal

To select all the logs, use the show logging profile wireless internal command.

show logging profile wireless internal

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

Ensure that you enable internal keyword using the show logging profile wireless internal command to get the trace output.

Without the internal keyword, only customer curated logs are displayed.

Examples

The following example shows how to display all the logs:

Device# show logging profile wireless internal

show logging profile wireless level

To select logs above a specific level, use the show logging profile wireless level command.

show logging profile wireless level { debug | emergency | error | info | noise | notice | verbose | warning }

Syntax Description


debug	Selects debug messages.
emergency	Selects emergency possible messags.
error	Selects error messages.
info	Selects informational messages.
noise	Selects maximum possible messages.
notice	Selects notice messages.
verbose	Selects verbose debug messages.
warning	Selects warning messages.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

Ensure that you enable internal keyword using the show logging profile wireless internal command to get the trace output.

Without the internal keyword, only customer curated logs are displayed.

Examples

The following example shows how to select logs above a specific level:

Device# show logging profile wireless level info

show logging profile wireless module

To select logs for specific modules, use the show logging profile wireless module command.

show logging profile wireless module module-name

Syntax Description


`module-name`	A comma or space separated list of module names. For example, dbal, tdllib or "dbal tdllib".

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

Ensure that you enable internal keyword using the show logging profile wireless internal command to get the trace output.

Without the internal keyword, only customer curated logs are displayed.

Examples

The following example shows how to select logs for specific modules:

Device# show logging profile wireless module dbal

show logging profile wireless reverse

To view logs in reverse chronological order, use the show logging profile wireless reverse command.

show logging profile wireless reverse

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

Ensure that you enable internal keyword using the show logging profile wireless internal command to get the trace output.

Without the internal keyword, only customer curated logs are displayed.

Examples

The following example shows how to view logs in reverse chronological order:

Device# show logging profile wireless reverse

show logging profile wireless start

To specify log filtering start location, use the show logging profile wireless start command.

show logging profile wireless start { marker marker | timestamp time-stamp}

Syntax Description


marker	The marker to start filtering from. It must match with previously set marker.
timestamp	The timestamp for filtering. for example, "2017/02/10 14:41:50.849".

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

Ensure that you enable internal keyword using the show logging profile wireless internal command to get the trace output.

Without the internal keyword, only customer curated logs are displayed.

Examples

The following example shows how to specify log filtering start location:

Device# show logging profile wireless start timestamp 2017/02/10 14:41:50.849

show logging profile wireless switch

To specify the switch to look for logs, use the show logging profile wireless switch command.

show logging profile wireless switch { switch-num | active| standby}

Syntax Description


`chassis-num`	Chassis number.
active	Selects the active instance.
standby	Selects the standby instance.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

Ensure that you enable internal keyword using the show logging profile wireless internal command to get the trace output.

Without the internal keyword, only customer curated logs are displayed.

Examples

The following example shows how to specify the chassis number to look for logs:

Device# show logging profile wireless switch active

show logging profile wireless to-file

To decode files stored in disk and write the output to a file, use the show logging profile wireless to-file command.

show logging profile wireless to-file output-file-name

Syntax Description


`output-file-name`	Output file name. File with this name will be created in the flash memory.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

Ensure that you enable internal keyword using the show logging profile wireless internal command to get the trace output.

Without the internal keyword, only customer curated logs are displayed.

Examples

The following example shows how to decode files stored in disk and write the output to a file:

Device# show logging profile wireless to-file testfile

show mdns-sd cache

To view mDNS cache details, use the show mdns-sd cache command.

show mdns-sd cache { ap-mac mac-address (H.H.H) | client-mac client-mac-address (H.H.H) | detail | glan-id <1 - 5> | location-group <0 - 4096> | mdns-ap mdns-ap mac address (H.H.H) | rlan-id <1 - 128> | statistics | type { A-AAAA | PTR | SRV | TXT } | udn { <1 - 4294967295> | shared } | wired | wlan-id <0 - 4096> }

Syntax Description


ap-mac `mac-address (H.H.H)`	Specifies the AP Ethernet MAC address.
client-mac `client-mac-address (H.H.H)`	Specifies the client MAC address.
detail	Specifes the cache in detail.
location-group `<0 - 4096>`	Specifies the location group. The value range is from 0 to 4096.
mdns-ap `mdns-ap mac address (H.H.H)`	Specifies the cache learnt from a specific mDNS AP.
rlan-id `<1 - 128>`	Specifies the remote LAN ID. The value range is from 1 - 128.
statistics	Specifies the mDNS cache statistics.
type	Specifies the mDNS record type. The record types are, A-AAAA, PTR, SRV, and TXT.
udn `<1 - 4294967295>`	Specifies the UDN ID. The value range is from 1 to 4294967295.
shared	Specifies the UDN shared services.
wired	Specifies the mDNS services from wired clients.
wlan-id `<0 - 4096>`	Specifies the WLAN ID. The value range is from 1 to 4096.

Command Default

None

Command Modes

Privileged EXEC mode

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.3.1	This command was introduced.

Usage Guidelines

None

Examples

The following example shows how to view the mDNS cache details:

Device# show mdns-sd cache

show mdns-sd cache detail

To view the multicast DNS (mDNS) cache details, use the show mdns-sd cache detail command.

show mdns-sd cache detail

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.1.1s	This command was introduced.

Examples

The following is sample output from the show mdns-sd cache detail command:

Device# show mdns-sd cache detail

Name: _printer._tcp.local
  Type: PTR
  TTL: 4500
  VLAN: 21
  Client MAC: ace2.d3bc.047e                  
  Remaining-Time: 4383
  mDNS Service Policy: default-mdns-service-policy
  Rdata: HP OfficeJet Pro 8720 [BC047E] (2)._printer._tcp.local

show mdns-sd cache upn shared

To view the multicast DNS (mDNS) cache user personal network shared services details, use the show mdns-sd cache upn shared command.

show mdns-sd cache upn shared

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.1.1s	This command was introduced.

Examples

The following is sample output from the show mdns-sd cache upn shared command that displays the mDNS cache UPN shared services details:

Device# show mdns-sd cache upn shared

------------------------------------------------------------- PTR Records -----------------------------------------------------------------
RECORD-NAME                                    TTL      TYPE      ID    CLIENT-MAC       RR-RECORD-DATA
-------------------------------------------------------------------------------------------------------------------------------------------
9.1.1.7.5.D.E.F.F.F.6.C.7.E.2.1.0.0.0.0.0.0.0  4500     WLAN      2     10e7.c6d5.7119   HP10E7C6D57119-2860.local
_services._dns-sd._udp.local                   4500     WLAN      2     10e7.c6d5.7119   _ipps._tcp.local
_universal._sub._ipps._tcp.local               4500     WLAN      2     10e7.c6d5.7119   HP DeskJet 5000 series [D57119] (3127)._ipps._tcp.
_print._sub._ipps._tcp.local                   4500     WLAN      2     10e7.c6d5.7119   HP DeskJet 5000 series [D57119] (3127)._ipps._tcp.
_ePCL._sub._ipps._tcp.local                    4500     WLAN      2     10e7.c6d5.7119   HP DeskJet 5000 series [D57119] (3127)._ipps._tcp.
_ipps._tcp.local                               4500     WLAN      2     10e7.c6d5.7119   HP DeskJet 5000 series [D57119] (3127)._ipps._tcp.
_services._dns-sd._udp.local                   4500     WLAN      2     10e7.c6d5.7119   _ipp._tcp.local
_universal._sub._ipp._tcp.local                4500     WLAN      2     10e7.c6d5.7119   HP DeskJet 5000 series [D57119] (3127)._ipp._tcp.l
_print._sub._ipp._tcp.local                    4500     WLAN      2     10e7.c6d5.7119   HP DeskJet 5000 series [D57119] (3127)._ipp._tcp.l
_ePCL._sub._ipp._tcp.local                     4500     WLAN      2     10e7.c6d5.7119   HP DeskJet 5000 series [D57119] (3127)._ipp._tcp.l
.
.
.
------------------------------------------------------------- SRV Records -----------------------------------------------------------------
RECORD-NAME                                    TTL      TYPE      ID    CLIENT-MAC       RR-RECORD-DATA
-------------------------------------------------------------------------------------------------------------------------------------------
HP DeskJet 5000 series [D57119] (3127)._ipp._  4500     WLAN      2     10e7.c6d5.7119   0 0 631 HP10E7C6D57119-2860.local
HP DeskJet 5000 series [D57119] (3127)._http.  4500     WLAN      2     10e7.c6d5.7119   0 0 80 HP10E7C6D57119-2860.local
HP DeskJet 5000 series [D57119] (3127)._ipps.  4500     WLAN      2     10e7.c6d5.7119   0 0 631 HP10E7C6D57119-2860.local
HP DeskJet 5000 series [D57119] (3127)._uscan  4500     WLAN      2     10e7.c6d5.7119   0 0 8080 HP10E7C6D57119-2860.local
HP DeskJet 5000 series [D57119] (3127)._prive  4500     WLAN      2     10e7.c6d5.7119   0 0 80 HP10E7C6D57119-2860.local
HP DeskJet 5000 series [D57119] (3127)._uscan  4500     WLAN      2     10e7.c6d5.7119   0 0 443 HP10E7C6D57119-2860.local
HP DeskJet 5000 series [D57119] (3127)._scann  4500     WLAN      2     10e7.c6d5.7119   0 0 8080 HP10E7C6D57119-2860.local
HP DeskJet 5000 series [D57119] (3127)._pdl-d  4500     WLAN      2     10e7.c6d5.7119   0 0 9100 HP10E7C6D57119-2860.local
 
------------------------------------------------------------ A/AAAA Records ---------------------------------------------------------------
RECORD-NAME                                    TTL      TYPE      ID    CLIENT-MAC       RR-RECORD-DATA
-------------------------------------------------------------------------------------------------------------------------------------------
HP10E7C6D57119-2860.local                      4500     WLAN      2     10e7.c6d5.7119   8.16.16.99
 
------------------------------------------------------------- TXT Records -----------------------------------------------------------------
RECORD-NAME                                    TTL      TYPE      ID    CLIENT-MAC       RR-RECORD-DATA
-------------------------------------------------------------------------------------------------------------------------------------------
HP DeskJet 5000 series [D57119] (3127)._ipp._  4500     WLAN      2     10e7.c6d5.7119   [502]'txtvers=1''adminurl=http://HP10E7C6D57119-28
HP DeskJet 5000 series [D57119] (3127)._http.  4500     WLAN      2     10e7.c6d5.7119   [1]''
HP DeskJet 5000 series [D57119] (3127)._ipps.  4500     WLAN      2     10e7.c6d5.7119   [502]'txtvers=1''adminurl=http://HP10E7C6D57119-28
HP DeskJet 5000 series [D57119] (3127)._uscan  4500     WLAN      2     10e7.c6d5.7119   [280]'txtvers=1''adminurl=http://HP10E7C6D57119-28
HP DeskJet 5000 series [D57119] (3127)._prive  4500     WLAN      2     10e7.c6d5.7119   [124]'txtvers=1''ty=HP DeskJet 5000 series [D57119
HP DeskJet 5000 series [D57119] (3127)._uscan  4500     WLAN      2     10e7.c6d5.7119   [280]'txtvers=1''adminurl=http://HP10E7C6D57119-28
HP DeskJet 5000 series [D57119] (3127)._scann  4500     WLAN      2     10e7.c6d5.7119   [177]'txtvers=1''adminurl=http://HP10E7C6D57119-28
HP DeskJet 5000 series [D57119] (3127)._pdl-d  4500     WLAN      2     10e7.c6d5.7119   [211]'txtvers=1''rp=''priority=40''UUID=9fe36149-9

show mdns-sd cache upn detail

To view the multicast DNS (mDNS) cache user personal network identifier details, use the show mdns-sd cache upn detail command.

show mdns-sd cache upnupn-id detail

Syntax Description


`upn-id`	User personal network identifier.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.1.1s	This command was introduced.

Examples

The following is sample output from the show mdns-sd cache upn detail command that displays the mDNS cache UPN identifier details:

Device# show mdns-sd cache upn 777 detail

Name: _services._dns-sd._udp.local
  Type: PTR
  TTL: 4500
  WLAN: 2
  WLAN Name: mdns-psk
  VLAN: 16
  Client MAC: f4f9.51e2.a6a6                  
  AP Ethernet MAC: 002a.1087.d68a                  
  Remaining-Time: 4486
  Site-Tag: default-site-tag
  mDNS Service Policy: madhu-mDNS-Policy
  Overriding mDNS Service Policy: NO
  UPN-ID: 7777
  UPN-Status: Enabled
  Rdata: _airplay._tcp.local

show mdns-sd flexconnect summary

To view the summary of the mDNS flexconnect sites, use the show mdns-sd flexconnect summary command.

show mdns-sd flexconnect summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC mode

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.3.1	This command was introduced.

Usage Guidelines

None

Examples

The following example shows how to view the summary of mDNS flexconnect sites:

Device# show mdns-sd flexconnect summary

show mdns-sd statistics

To view the mDNS statistics, use the show mdns-sd statistics command.

show mdns-sd statistics { debug | flexconnect | rlan-id <1 - 128> wired | wlan-id <1 - 4096> }

Syntax Description


debug	Specifies the mDNS debug statistics.
flexconnect	Specifies the mDNS flexconnect statistics.
rlan-id`<1 - 128>`	Specifies the remote LAN (RLAN) ID. The value range is from 1 to 128.
wired	Specifies the mDNS wired statistics.
wlan-id`<1 - 4096>`	Specifies the WLAN ID. The value range is from 1 to 4096.

Command Default

None

Command Modes

Privileged EXEC mode

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.3.1	This command was introduced.

Usage Guidelines

None

Examples

The following example shows how to view the mDNS statistics:

Device# show mdns-sd statistics

show mdns-sd summary

To view the summary of mDNS service discovery configuration, use the show mdns-sd summary command.

show mdns-sd summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC mode

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.3.1	This command was introduced.

Usage Guidelines

None

Examples

The following example shows how to view the summary of mDNS service discovery configuration:

Device# show mdns-sd summary

show mdns-sd sp-sdg statistics

To verify the Service-Peer SDG communication statistics, use the show mdns-sd sp-sdg statistics command.

show mdns-sd sp-sdg statistics

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.5.1	This command was introduced.

Examples

The following example shows how to verify the Service-Peer SDG communication statistics:

Device# show mdns-sd sp-sdg statistics
                         One min, 5 mins, 1 hour
Average Input rate (pps) :    0,       0,    0
Average Output rate (pps) :   0,       0,    0
Messages sent:
Query : 0
ANY query : 0
Advertisements : 0
Advertisement Withdraw : 0
Interface down : 0
Vlan down : 0
Service-peer ID change : 0
Service-peer cache clear : 0
Resync response : 0
Keep-Alive : 1
Messages received:
Query response : 0
ANY Query response : 0
Cache-sync : 0
Get service-instance : 0
Keep-Alive response : 1

show mobility

To display information about the Layer 3 mobility and the wireless network, use the showmobility command in privileged EXEC mode.

show mobility {ap [ip-address] | mn [ip ip-address] | mac mac-address | network network-id | status}

Syntax Description


ap	Displays information about the access point.
`ip-address`	(Optional) IP address.
mn	Displays information about the mobile node.
ip `ip-address`	(Optional) Displays information about the IP database thread.
mac `mac-address`	Displays information about the MAC database thread.
network `network-id`	Displays information for a specific wireless network ID.
status	Displays status information.

Command Modes

Privileged EXEC

Command History


Release	Modification
12.2(18)SXD	This command was introduced on the Supervisor Engine 720.
12.2(18)SXD3	The output of this command was changed to include the TCP adjust-mss status.
12.2(33)SRA	This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

This command is supported on Cisco 7600 series routers that are configured with a WLSM only.

Examples

This example shows how to display information about the access point:


Router# show mobility
 ap
AP IP Address   AP Mac Address Wireless Network-ID
--------------- -------------- -------------------
10.1.1.2 000d.29a2.a852 101 102 109 103

This example shows how to display information about the access points for a specific network ID:


Router# show mobility
 ap 172.16.1.2 detail
IP Address : 172.16.1.2
MAC Address : 000d.29a2.a852
Participating Wireless Tunnels: 101, 102, 109, 103
Registered Mobile Nodes on AP {172.16.1.2, 000d.29a2.a852} :
MN Mac Address MN IP Address AP IP Address Wireless Network-ID
-------------- --------------- --------------- -------------------
000a.8afa.85c9 10.1.3.11 172.16.1.2 103
000d.bdb7.83f7 10.1.2.11 172.16.1.2 102
000d.bdb7.83fb 10.1.1.11 172.16.1.2 101
Router# show mobility
 network-id 101
Wireless Network ID : 101
Wireless Tunnel Source IP Address : 10.1.1.1
Wireless Network Properties : Trusted
Wireless Network State : Up
Registered Access Point on Wireless Network 101:
AP IP Address AP Mac Address Wireless Network-ID
--------------- -------------- -------------------
176.16.1.2 000d.29a2.a852 101 102 109 103
Registered Mobile Nodes on Wireless Network 101:
MN Mac Address MN IP Address AP IP Address Wireless Network-ID
-------------- --------------- --------------- -------------------
000d.bdb7.83fb 10.1.1.11 176.16.1.2 101
Router# show mobility
 status
WLAN Module is located in Slot: 4 (HSRP State: Active) LCP
Communication status      : up 
MAC address used for Proxy ARP: 0030.a349.d800 
Number of Wireless Tunnels    : 1 
Number of Access Points       : 2 
Number of Mobile Nodes        : 0 
Wireless Tunnel Bindings: 
Src IP Address   Wireless Network-ID  Flags
---------------  -------------------  ------- 
10.1.1.1          101                  B 
Flags: T=Trusted, B=IP Broadcast enabled, A=TCP Adjust-mss enabled

Related Commands


Command	Description
mobility	Configures the wireless mGRE tunnels.

show monitor capture

To display the contents of a monitor capture buffer or a capture point, use the show monitor capture command in privileged EXEC mode.

show monitor capture [ epc-capture-name [ parameter | buffer [ brief | detailed | dump ] ] ]

Syntax Description


`epc-capture-name`	Specifies the name of the embedded packet capture.
buffer	Displays the contents of the specified capture buffer.
dump	(Optional) Displays a hexadecimal dump of the captured packet in addition to the metadata.
brief	(Optional) Provides a brief output of the captured packet information.
detail	(Optional) Provides a detailed output of the captured packet information.
parameter	Reconstructs and displays EXEC commands that were used to specify the capture.
detailed	Provides a detailed output of the captured packet information.

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.12.1	This command was introduced.

Usage Guidelines

You can enter the show monitor capture command when the capture buffer is not in the running state.

If you enter the detail keyword, packets are decoded to the Layer 4 protocol level and displayed. If you enter the dump keyword, non-IP packets are displayed in hexadecimal dump format. An ACL can be configured as a display filter so that only packets permitted by the ACL are displayed.

Examples

The following example shows how to display all the packets in a capture buffer. The output is self-explanatory.


Device# show monitor capture mycap buffer

buffer size (KB) : 2048000
buffer used (KB) : 128
packets in buf : 17
packets dropped : 0
packets per sec : 3

The following example shows how to display the list of commands that were used to specify the capture:


Device# show monitor capture cap1 parameter

  monitor capture cap1 interface GigabitEthernet 1/0/1 both
  monitor capture cap1 match any
  monitor capture cap1 buffer size 10
  monitor capture cap1 limit pps 1000

The following example shows how to display brief output from the captured packet information. The output is self-explanatory.


Device# show monitor capture cap1 buffer brief

------------------------------------------------------------------
#   size   timestamp     source             destination   protocol
------------------------------------------------------------------
   0   62    0.000000   10.0.0.1         ->  203.0.113.254  UDP
   1   46    0.267992   10.0.1.2         ->  203.0.113.204  IGMP
   2   76    0.428979   172.16.255.3     ->  172.16.255.3   UDP
   3   62    1.613982   10.0.29.1        ->  172.16.200.2   UDP
   4   74    1.659970   10.0.1.3         ->  10.0.0.10      EIGRP
   5   90    2.016006   10.29.0.4        ->  203.0.113.224  UDP
   6   74    2.088008   10.1.9.2         ->  203.0.113.10   EIGRP
   7   76    2.114008   172.17.254.1     ->  172.16.255.1   UDP
   8   74    2.245990   10.29.0.3        ->  203.0.113.10   EIGRP
   9   46    2.262987   10.0.0.0         ->  203.0.113.1    IGMP
  10   77    2.362988   10.1.9.2         ->  203.0.113.10   EIGRP
  11   62    2.631971   10.29.0.2        ->  203.0.113.2    UDP
  12   74    2.934009   10.29.0.5        ->  203.0.113.10   EIGRP
  13   74    3.331984   10.29.0.6        ->  203.0.113.10   EIGRP
  14   46    3.499974   10.0.0.0         ->  203.0.113.1    IGMP
  15   46    4.304992   10.0.0.0         ->  203.0.113.1    IGMP
  16   76    5.157005   172.16.255.3     ->  172.17.255.3   UDP

The following example shows how to display all the packets in a capture buffer. The output is self-explanatory.


Device# show monitor capture cap1 buffer detailed 

 -----------------------------------------------------------------
#   size   timestamp     source             destination   protocol
------------------------------------------------------------------
   0   62    0.000000   10.29.0.2         ->  172.16.255.3   UDP
  0000:  01005E00 00020000 0C07AC1D 080045C0   ..^...........E.
  0010:  00300000 00000111 CFDC091D 0002E000   .0..............
  0020:  000207C1 07C1001C 802A0000 10030AFA   .........*......
  0030:  1D006369 73636F00 0000091D 0001       ..example.......

   1   46    0.267992   10.0.0.0          ->  172.16.255.1   IGMP
  0000:  01005E00 0002001B 2BF69280 080046C0   ..^.....+.....F.
  0010:  00200000 00000102 44170000 0000E000   . ......D.......
  0020:  00019404 00001700 E8FF0000 0000       ..............

   2   76    0.428979   172.16.255.3     ->  172.17.255.3    UDP
  0000:  00000C07 AC1DB414 89031124 080045C0   ...........$..E.
  0010:  003E0000 0000FF11 64C5AC10 FF03AC11   .>......d.......
  0020:  FF030286 0286002A 84A40001 001EAC10   .......*........
  0030:  FF030000 01000014 00000000 04000004   ................

   3   62    1.613982   10.26.11.3        ->  172.16.255.1    UDP
  0000:  01005E00 0002001B 2BF68680 080045C0   ..^.....+.....E.
  0010:  00300000 00000111 CFDB091D 0003E000   .0..............
  0020:  000207C1 07C1001C 88B50000 08030A6E   ...............n
  0030:  1D006369 73636F00 0000091D 0001       ..example.......

   4   74    1.659970   10.29.3.2         ->  172.16.255.2   EIGRP
  0000:  01005E00 000A001B 2BF69280 080045C0   ..^.....+.....E.
  0010:  003C0000 00000258 CE81091D 0002E000   .<.....X........
  0020:  000A0205 F3000000 00000000 00000000   ................
  0030:  00000000 00D10001 000C0100 01000000   ................

   5   90    2.016006   10.22.1.4         ->  203.0.113.1     UDP
  0000:  FFFFFFFF FFFF001C 0F2EDC00 080045C0   ..............E.
  0010:  004C0000 00000111 AFC1091D 0004FFFF   .L..............
  0020:  FFFF007B 007B0038 5B14E500 06E80000   ...{.{.8[.......
  0030:  00000021 BE23494E 49540000 00000000   ...!.#INIT......

The following example shows how to display a hexadecimal dump of the captured packet:

Device# show monitor capture cap1 buffer dump 
0
 0000:  01005E00 00020000 0C07AC1D 080045C0   ..^...........E.
 0010:  00300000 00000111 CFDC091D 0002E000   .0..............
 0020:  000207C1 07C1001C 802A0000 10030AFA   .........*......
 0030:  1D006369 73636F00 0000091D 0001       ..example.......

1
 0000:  01005E00 0002001B 2BF69280 080046C0   ..^.....+.....F.
 0010:  00200000 00000102 44170000 0000E000   . ......D.......
 0020:  00019404 00001700 E8FF0000 0000       ..............

2
 0000:  01005E00 0002001B 2BF68680 080045C0   ..^.....+.....E.
 0010:  00300000 00000111 CFDB091D 0003E000   .0..............
 0020:  000207C1 07C1001C 88B50000 08030A6E   ...............n
 0030:  1D006369 73636F00 0000091D 0001       ..example.......

3
 0000:  01005E00 000A001C 0F2EDC00 080045C0   ..^...........E.
 0010:  003C0000 00000258 CE7F091D 0004E000   .<.....X........
 0020:  000A0205 F3000000 00000000 00000000   ................
 0030:  00000000 00D10001 000C0100 01000000   ................
 0040:  000F0004 00080501 0300                ..........

show nmsp

To display the Network Mobility Services Protocol (NMSP) configuration settings, use the show nmsp command.

show nmsp {attachment | {suppress interfaces} | capability | notification interval | statistics {connection | summary} | status | subscription detail [ ip-addr ] | summary}

Syntax Description


attachment suppress interfaces	Displays attachment suppress interfaces.
capability	Displays NMSP capabilities.
notification interval	Displays the NMSP notification interval.
statistics connection	Displays all connection-specific counters.
statistics summary	Displays the NMSP counters.
status	Displays status of active NMSP connections.
subscription detail `ip-addr`	The details are only for the NMSP services subscribed to by a specific IP address.
subscription summary	Displays details for all of the NMSP services to which the controller is subscribed. The details are only for the NMSP services subscribed to by a specific IP address.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following is sample output from the show nmsp notification interval command:


Device#  show nmsp notification interval
NMSP Notification Intervals
---------------------------

RSSI Interval:
 Client               : 2 sec
 RFID                 : 2 sec
 Rogue AP             : 2 sec
 Rogue Client         : 2 sec
Attachment Interval   : 30 sec
Location Interval     : 30 sec

show nmsp cloud-services statistics

To see NMSP cloud-service statistics, use the show nmsp cloud-services statistics command.

show nmsp cloud-services statistics [ chassis {chassis-number | active | standby} R0]

Syntax Description


`chassis-number`	Chassis number as either 1 or 2.
active R0	Active instance of the active NMSP cloud services in Route-processor slot 0.
standby R0	Standby instance of the active NMSP cloud services in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

This example shows how to see NMSP cloud-service statistics:

Device# show nmsp cloud-services statistics

show nmsp cloud-services summary

To see a summary of information about NMSP cloud-services, use the show nmsp cloud-services summary command.

show nmsp cloud-services summary [ chassis {chassis-number | active | standby} R0]

Syntax Description


`chassis-number`	Chassis number as either 1 or 2.
active R0	Active instance of the NMSP cloud services in Route-processor slot 0.
standby R0	Standby instance of the active NMSP cloud services in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

This example shows how to see NMSP cloud-service summary information:

Device# show nmsp cloud-services summary

show nmsp subscription group detail all

To display the mobility services group subscription details of all CMX connections, use the show nmsp subscription group detail all command.

show nmsp subscription group detail all

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following example shows how to display the mobility services group subscription details of all CMX connections:

Device# show nmsp subscription group detail all

show nmsp subscription group detail ap-list

To display the AP MAC list subscribed for a group by a CMX connection, use the show nmsp subscription group detail ap-list command.

show nmsp subscription group detail ap-list group-name cmx-IP-addrress

Syntax Description


`group-name`	CMX AP group name.
`cmx-IP-addrress`	CMX IP address.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following example shows how to verify the AP MAC list subscribed for a group by a CMX connection.

Device# show nmsp subscription group detail ap-list Group1 127.0.0.1 

CMX IP address: 127.0.0.1
CMX Group name: Group1
CMX Group AP MACs:
: 00:00:00:00:70:02  00:00:00:00:66:02  00:99:00:00:00:02  00:00:00:bb:00:02
  00:00:00:00:55:02  00:00:00:00:50:02  00:33:00:00:00:02  00:d0:00:00:00:02
  00:10:00:10:00:02  00:00:00:06:00:02  00:00:00:02:00:02  00:00:00:00:40:02
  00:00:00:99:00:02  00:00:00:00:a0:02  00:00:77:00:00:02  00:22:00:00:00:02
  00:00:00:00:00:92  00:00:00:00:00:82  00:00:00:00:03:02  aa:00:00:00:00:02
  00:00:00:50:00:42  00:00:0d:00:00:02  00:00:00:00:00:32  00:00:00:cc:00:02
  00:00:00:88:00:02  20:00:00:00:00:02  10:00:00:00:00:02  01:00:00:00:00:02
  00:00:00:00:00:02  00:00:00:00:00:01  00:00:00:00:00:00

show nmsp subscription group detail services

To display the services subscribed for a group by a CMX connection, use the show nmsp subscription group detail services command.

show nmsp subscription group detail services group-name cmx-IP-addrress

Syntax Description


`group-name`	CMX AP group name.
`cmx-IP-addrress`	CMX IP address.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following example shows how to verify the services subscribed for a group by a CMX connection.

Device# show nmsp subscription group detail services Group1 127.0.0.1 

CMX IP address: 127.0.0.1
CMX Group name: Group1
CMX Group filtered services:
Service            Subservice
-----------------------------
RSSI               Mobile Station,
Spectrum
Info
Statistics

show nmsp subscription group summary

To display the mobility services group subscription summary of all CMX connections, use the show nmsp subscription group summary command.

show nmsp subscription group summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following example shows how to verify the mobility services group subscription summary of all CMX connections.

Device# show nmsp subscription group summary 

CMX IP address: 127.0.0.1
  Groups subscribed by this CMX server:
  Group name: Group1

show ntp associations

To display the status of Network Time Protocol (NTP) associations, use the show ntp associations command in privileged EXEC mode.

show ntp associations

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC(#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to view NTP associations. :

Device# show ntp associations 
  address         ref clock       st   when   poll reach  delay  offset   disp
*~10.1.1.99       72.163.32.44     2    918   1024   377  0.177   7.618  1.102
* sys.peer, # selected, + candidate, - outlyer, x falseticker, ~ configured
--

show parameter-map type webauth name

To verify the webauth parameters of a parameter map, use the show parameter-map type webauth name command.

show parameter-map type webauth name parameter-map name

Syntax Description


`parameter-map name`	Name of the parameter map.

Command Default

None

Command Modes

Global configuration (config)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to verify the webauth parameters of a parameter map:

Device# configure terminal
Device(config)# show parameter-map type webauth name parameter-map-name

show platform conditions

To see information about conditional debugs, use the show platform conditions command.

show platform conditions

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see information about conditional debugs:

Device# show platform conditions

show platform hardware

To see the hardware platform Quantum flow processor datapath statistics, use the show platform hardware chassis active qfp feature wireless wlclient datapath cpp-if-handle statistics command.

show hardware chassis active qfp feature wireless wlclient datapath cpp-if-handle client-cpp-value statistics {clear | start | stop}

Syntax Description


active	Active instance.
qfp	Quantum Flow Processor.
wlclient	QFP wireless client.
cpp-if-handle	client cpp interface handle.
`client-cpp-value`	Client cpp if-handle value. The range is between 1 and 4294967295.
statistics	Show Client Statistics.
clear	Shows and Clears the Client Statistics.
start	Start Client Statistics collection.
stop	Stop Client Statistics collection.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to start client statistics collection:

Device# show platform hardware chassis active qfp feature wireless wlclient datapath cpp-if-handle cpp-if-handle value statistics start

show platform hardware chassis active qfp feature dns-snoop-agent client enabled-intf

To view the DSA enabled interfaces, use the show platform hardware chassis active qfp feature dns-snoop-agent client enabled-intf command.

show platform hardware chassis active qfp feature dns-snoop-agent client enabled-intf

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the DSA enabled interfaces:

Device# show platform hardware chassis active qfp feature dns-snoop-agent client enabled-intf
Interface name: GigabitEthernet0/0/0, handle: 5

show platform hardware chassis active qfp feature dns-snoop-agent client hw-pattern-list

To view the OpenDNS string or FQDN filter for the pattern list, use the show platform hardware chassis active qfp feature dns-snoop-agent client hw-pattern-list command.

show platform hardware chassis active qfp feature dns-snoop-agent client hw-pattern-list { fqdn-filter fqdn_filter_ID | odns_string}

Syntax Description


fqdn-filter	Displays the FQDN filter for the pattern list.
`fqdn_filter_ID`	Refers to the FQDN filter ID. The valid range is from 1 to 16.
odns_string	Displays the OpenDNS string for the pattern list.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the FQDN filter for the pattern list:

Device# show platform hardware chassis active qfp feature dns-snoop-agent client hw-pattern-list fqdn-filter 1
Filter Name: urllist_flex_preauth

Name: url1.dns.com
Feature mask: 16, Dirty: 0, Ref count: 0, Match count: 0

show platform hardware chassis active qfp feature dns-snoop-agent client info

To view the DSA client details, use the show platform hardware chassis active qfp feature dns-snoop-agent client info command.

show platform hardware chassis active qfp feature dns-snoop-agent client info

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the DSA client details:

Device# show platform hardware chassis active qfp feature dns-snoop-agent client info
Number of patterns added/deleted/total: 2/0/2
Number of re_table rebuilt : : 0
Number of str_table rebuilt: : 2
Registered clients: 0x001ffff0
Number of transaction started/ended: 2/2
Memory pool size/limit: 512/81920
Pending Deletion Pattern List:

show platform hardware chassis active qfp feature dns-snoop-agent client pattern-list

To view the OpenDNS string or FQDN filter for the pattern list, use the show platform hardware chassis active qfp feature dns-snoop-agent client pattern-list command.

show platform hardware chassis active qfp feature dns-snoop-agent client pattern-list { fqdn-filter fqdn_filter_ID | odns_string}

Syntax Description


fqdn-filter	Displays the FQDN filter for the pattern list.
`fqdn_filter_ID`	Refers to the FQDN filter ID. The valid range is from 1 to 16.
odns_string	Displays the OpenDNS string for the pattern list.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the FQDN filter for the pattern list:

Device# show platform hardware chassis active qfp feature dns-snoop-agent client pattern-list fqdn-filter 1
Filter Name: urllist_flex_preauth
Pattern List in CPP client: 1

Name: url1.dns.com
feature_mask: 0x00000010, hw_ptr: 0xdf86d510

show platform hardware chassis active qfp feature dns-snoop-agent datapath ip-cache

To view the DSA IP cache table details, use the show platform hardware chassis active qfp feature dns-snoop-agent datapath ip-cache command.

show platform hardware chassis active qfp feature dns-snoop-agent datapath ip-cache { address [ ipv4 ipv4_address | ipv6 ipv6_address] | all | pattern regex_pattern}

Syntax Description


address `[` ipv4 `ipv4_address` `\|` ipv6 `ipv6_address]`	Displays the DSA address entry details
all	Displays all the DSA IP cache address details
pattern `regex_pattern`	Displays the DSA IP cache pattern details

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the DSA address entry details:

Device# show platform hardware chassis active qfp feature dns-snoop-agent datapath ip-cache address ipv4 104.122.2.194  
IP address: 104.122.2.194, client(s): 32, regex: www.adobe.com, expire in 0 seconds

Examples

This example shows how to view all the DSA IP cache address details:

Device# show platform hardware chassis active qfp feature dns-snoop-agent datapath ip-cache all
IP Address        Client(s) Expire     Match         RegexId      Dirty
------------------------------------------------------------------------
172.217.13.228      2       132     .*google.com    0x4d7f9e20     0x0

Examples

This example shows how to view the DSA IP cache pattern details:

Device# show platform hardware chassis active qfp feature dns-snoop-agent datapath ip-cache pattern .*google*
1 IP Addresses matching pattern .*google*
IP Address                    Client(s)  Expire   Match       RegexId    Dirty
-------------------------------------------------------------------------------
2607:f8b0:4004:800:0:0:0:2004   32         13    .*google*   0x31156220   0x0

show platform hardware chassis active qfp feature dns-snoop-agent datapath memory

To view the DSA datapath memory details, use the show platform hardware chassis active qfp feature dns-snoop-agent datapath memory command.

show platform hardware chassis active qfp feature dns-snoop-agent datapath memory

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the DSA datapath memory details:

Device# show platform hardware chassis active qfp feature dns-snoop-agent datapath memory
Table-Name   Address      Size     
-----------------------------------------
IP Cache DB   0xda5bb420   512            
IP Hash       0xda41f400   1024           
String Table  0xdec6ac10
String Table  0xda41f010

==DSA Chunk info==
Chunk-Pool   Allocated     Total_Free   Init-Num     Low_Wat
------------------------------------------------------------
ip cache chunk   0             512          512          512    

==DSA Runtime Info==
------------------------------------------------------------
dsa init state 0x7   dsa client mask 0x100010

show platform hardware chassis active qfp feature dns-snoop-agent datapath regexp-table

To view the DSA regular expression table, use the show platform hardware chassis active qfp feature dns-snoop-agent datapath regexp-table command.

show platform hardware chassis active qfp feature dns-snoop-agent datapath regexp-table

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the DSA regular expression table:

Device# show platform hardware chassis active qfp feature dns-snoop-agent datapath regexp-table
String Table 0xdec6ac10     WLS_FQDN_GRP_1
String Table 0xda41f010     ODNS String

show platform hardware chassis active qfp feature dns-snoop-agent datapath stats

To view the DSA statistics, use the show platform hardware chassis active qfp feature dns-snoop-agent datapath stats command.

show platform hardware chassis active qfp feature dns-snoop-agent datapath stats

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the DSA statistics:

Device# show platform hardware chassis active qfp feature dns-snoop-agent datapath stats
DNS Snoop Agent Stats:
  parser unknown pkt: 0
  parser not needed: 0
  parser fmt error: 0
  parser pa error: 0
  parser non resp: 0
  parser multiple name: 0
  parser dns name err: 0
  parser matched ip: 0
  parser redirect: 0
  parser whitelist redirect: 0
  parser blacklist redirect: 0
  parser invalid redirect ip: 0
  parser skip: 0
  regex locked: 0
  regex not matched: 0
  pkt drop whitelist no redirect ip: 0
  pkt drop blacklist no redirect ip: 0
  entries in use: 0
  ip cache allocation fail: 0
  ip addr add: 0
  ip addr update: 0
  ip addr delete: 0
  ip addr cache hit: 0
  ip addr cache miss: 0
  ip addr bad param: 0
  ip addr delete not found: 0
  ip cache not initialized: 0

show platform hardware chassis active qfp feature et-analytics datapath runtime

To view the ETA global state in datapath, use the show platform hardware chassis active qfp feature et-analytics datapath runtime command.

show platform hardware chassis active qfp feature et-analytics datapath runtime

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to view the ETA global and interface details:

Device# show platform hardware chassis active qfp feature et-analytics datapath runtime
ET-Analytics run-time information:
   Feature state: initialized (0x00000004)
   Inactive timeout : 15 secs (default 15 secs)
   WhiteList information :
      flag: False
      cgacl w0 : n/a
      cgacl w1 : n/a
   Flow CFG information :
      instance ID : 0x0
      feature ID : 0x1
      feature object ID : 0x1
      chunk ID : 0xC

show platform hardware chassis active qfp feature et-analytics datapath memory

To view the ETA memory details, use the show platform hardware chassis active qfp feature et-analytics datapath memory command.

show platform hardware chassis active qfp feature et-analytics datapath memory

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the ETA memory details:

Device# show platform hardware chassis active qfp feature et-analytics datapath memory
ET-Analytics memory information:
   Size of FO : 3200 bytes
   No. of FO allocs : 0
   No. of FO frees : 0

show platform hardware chassis active qfp feature et-analytics datapath stats export

To view the ETA flow export in datapath, use the show platform hardware chassis active qfp feature et-analytics datapath stats export command.

show platform hardware chassis active qfp feature et-analytics datapath stats export

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the ETA flow export in datapath:

Device# show platform hardware chassis active qfp feature et-analytics datapath stats export
ET-Analytics 192.168.5.2:2055 vrf 0 Stats:
   Export statistics:
      Total records exported : 5179231
      Total packets exported : 3124873
      Total bytes exported : 3783900196
      Total dropped records : 0
      Total dropped packets : 0
      Total dropped bytes : 0
      Total IDP records exported :
            initiator->responder : 1285146
            responder->initiator : 979284
      Total SPLT records exported:
            initiator->responder : 1285146
            responder->initiator : 979284
      Total SALT records exported:
            initiator->responder : 0
            responder->initiator : 0
      Total BD records exported :
            initiator->responder : 0
            responder->initiator : 0
      Total TLS records exported :
            initiator->responder : 309937
            responder->initiator : 329469

show platform hardware chassis active qfp feature et-analytics datapath stats flow

To view the ETA flow statistics, use the show platform hardware chassis active qfp feature et-analytics datapath stats flow command.

show platform hardware chassis active qfp feature et-analytics datapath stats flow

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the ETA flow statistics:

Device# show platform hardware chassis active qfp feature et-analytics datapath stats flow
ET-Analytics Stats:
   Flow statistics:
      feature object allocs : 0
      feature object frees : 0
      flow create requests : 0
      flow create matching : 0
      flow create successful: 0
      flow create failed, CFT handle: 0
      flow create failed, getting FO: 0
      flow create failed, malloc FO : 0
      flow create failed, attach FO : 0
      flow create failed, match flow: 0
      flow create, aging already set: 0
      flow ageout requests : 0
      flow ageout failed, freeing FO: 0
      flow ipv4 ageout requests : 0
      flow ipv6 ageout requests : 0
      flow whitelist traffic match : 0

show platform hardware chassis active qfp feature wireless et-analytics eta-pending-client-tree

To view clients in the ETA pending wireless client tree, use the show platform hardware chassis active qfp feature wireless et-analytics eta-pending-client-tree command.

show platform hardware chassis active qfp feature wireless et-analytics eta-pending-client-tree

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view clients in the ETA pending wireless client tree:

Device# show platform hardware chassis active qfp feature wireless et-analytics
eta-pending-client-tree
CPP IF_H    DPIDX        MAC Address    VLAN   AS  MS  WLAN        POA
--------------------------------------------------------------------------
0X2A      0XA0000001    2c33.7a5b.827b  160    RN  LC ewlc_ssid 0x90000003
0X2B      0XA0000002    2c33.7a5b.80fb  160    RN  LC ewlc_ssid 0x90000003

show platform hardware chassis active qfp feature wireless et-analytics statistics

To view the ETA pending wireless client tree statistics, use the show platform hardware chassis active qfp feature wireless et-analytics statistics command.

show platform hardware chassis active qfp feature wireless et-analytics statistics

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the ETA pending wireless client tree statistics:

Device# show platform hardware chassis active qfp feature wireless et-analytics statistics
Wireless ETA cpp-client plumbing statistics
Number of ETA pending clients : 2
Counter                                             Value
-------------------------------------------------------------------
Enable ETA on wireless client called                  0
Delete ETA on wireless client called                  0
ETA global cfg init cb TVI FIA enable error           0
ETA global cfg init cb output SB read error           0
ETA global cfg init cb output SB write error          0
ETA global cfg init cb input SB read error            0
ETA global cfg init cb input SB write error           0
ETA global cfg init cb TVI FIA enable success         0
ETA global cfg uninit cb ingress feat disable         0
ETA global cfg uninit cb ingress cfg delete           0
ETA global cfg uninit cb egress feat disable          0
ETA global cfg uninit cb egress cfg delete er         0
ETA pending list insert entry called                  4
ETA pending list insert invalid arg error             0
ETA pending list insert entry exists error            0
ETA pending list insert no memory error               0
ETA pending list insert entry failed                  0
ETA pending list insert entry success                 4
ETA pending list delete entry called                  2
ETA pending list delete invalid arg error             0
ETA pending list delete entry missing                 0
ETA pending list delete entry remove error            0
ETA pending list delete entry success                 2

show platform hardware slot R0 ha_port interface stats

To see the HA port interface setting status, use the show platform hardware slot R0 ha_port interface stats command.

show platform hardware slot R0 ha_port interface stats

Syntax Description


This command has no arguments or keywords.

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.5.1	This command was introduced.

Examples

This example shows how to see the HA port interface setting status:


Device# show platform hardware slot R0 ha_port interface stats
HA Port
ha_port   Link encap:Ethernet  HWaddr 70:18:a7:c8:80:70
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Memory:e0900000-e0920000


Settings for ha_port:
        Supported ports:            [ TP ]
        Supported link modes:       10baseT/Half 10baseT/Full
                                    100baseT/Half 100baseT/Full
                                    1000baseT/Full
        Supported pause frame use:   Symmetric
        Supports auto-negotiation:   Yes
        Supported FEC modes:         Not reported
        Advertised link modes:       10baseT/Half 10baseT/Full
                                     100baseT/Half 100baseT/Full
                                     1000baseT/Full
        Advertised pause frame use:  Symmetric
        Advertised auto-negotiation: Yes
        Advertised FEC modes:        Not reported
        Speed:                       Unknown!
        Duplex:                      Unknown! (255)
        Port:                        Twisted Pair
        PHYAD:                       1
        Transceiver:                 internal
        Auto-negotiation:            on
        MDI-X:                       off (auto)
        Supports Wake-on:            pumbg
        Wake-on:                     g
        Current message level:       0x00000007 (7)
                                     drv probe link
        Link detected:               no

NIC statistics:
     rx_packets:             0
     tx_packets:             0
     rx_bytes:               0
     tx_bytes:               0
     rx_broadcast:           0
     tx_broadcast:           0
     rx_multicast:           0
     tx_multicast:           0
     multicast:              0
     collisions:             0
     rx_crc_errors:          0
     rx_no_buffer_count:     0
     rx_missed_errors:       0
     tx_aborted_errors:      0
     tx_carrier_errors:      0
     tx_window_errors:       0
     tx_abort_late_coll:     0
     tx_deferred_ok:         0
     tx_single_coll_ok:      0
     tx_multi_coll_ok:       0
     tx_timeout_count:       0
     rx_long_length_errors:  0
     rx_short_length_errors: 0
     rx_align_errors:        0
     tx_tcp_seg_good:        0
     tx_tcp_seg_failed:      0
     rx_flow_control_xon:    0
     rx_flow_control_xoff:   0
     tx_flow_control_xon:    0
     tx_flow_control_xoff:   0
     rx_long_byte_count:     0
     tx_dma_out_of_sync:     0
     tx_smbus:               0   
     rx_smbus:               0
     dropped_smbus:          0
     os2bmc_rx_by_bmc:       0
     os2bmc_tx_by_bmc:       0
     os2bmc_tx_by_host:      0
     os2bmc_rx_by_host:      0
     tx_hwtstamp_timeouts:   0
     rx_hwtstamp_cleared:    0
     rx_errors:              0
     tx_errors:              0
     tx_dropped:             0
     rx_length_errors:       0
     rx_over_errors:         0
     rx_frame_errors:        0
     rx_fifo_errors:         0
     tx_fifo_errors:         0
     tx_heartbeat_errors:    0
     tx_queue_0_packets:     0
     tx_queue_0_bytes:       0
     tx_queue_0_restart:     0
     tx_queue_1_packets:     0
     tx_queue_1_bytes:       0
     tx_queue_1_restart:     0
     rx_queue_0_packets:     0
     rx_queue_0_bytes:       0
     rx_queue_0_drops:       0
     rx_queue_0_csum_err:    0
     rx_queue_0_alloc_failed:0
     rx_queue_1_packets:     0
     rx_queue_1_bytes:       0
     rx_queue_1_drops:       0
     rx_queue_1_csum_err:    0
     rx_queue_1_alloc_failed:0

show platform integrity

To view the checksum record for boot stages, use the show platform integrity command.

show platform integrity [sign [nonce nonce ]]

Syntax Description


sign	(Optional). Show signature.
`nonce`	(Optional). Enter a nonce value.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.4.1	This command was introduced.

Examples

The following example shows how to view the checksum record for boot stages:

Device# show platform integrity sign nonce 123
Platform: C9800-L-F-K9
Boot 0 Version: R04.1173930452019-06-11
Boot 0 Hash: A6C92C44976FC77DD42234444FFD87798FB9036A2762FAA4999A190A0258B18C
Boot Loader Version: 16.12(1r)
Boot Loader Hash:
FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
OS Version: 2020-03-19_20.26
OS Hashes:
C9800-L-universalk9_wlc.2020-03-19_20.26.SSA.bin:
53E2DF1A1A082E36EA4CAB817C1794EC9D69AC0E90BCCBFECF9BCD0BCA9385AA9E9372ABF7431E4A08FC5E5B9670131C09D158E5B8A7B457501FE77AB9F1C26D
C9800-L-mono-universalk9_wlc.2020-03-19_20.26.SSA.pkg:
1D3279D53B0311CE42C669824DF86FB5596CD7CA45CA8D7FDC3D10657B8C9A48F4B0508D7BCFFD645CB6571AC1E674A57A82414E3D6E1666BE64E6132F707671
PCR0: EE14A2D5099DA343B3941C54A429C4AC1D3EE8E9B609F1AC00049768A470734E
PCR8: 78794D0F5667F8FA4E425E3CA2AF3CD99B90B219FD90222D622B3D563416BBAA

show platform software audit

To display the Security Enhanced Linux (SELinux) audit logs, use the show platform software audit command in privileged EXEC mode.

show platform software audit {all | summary | 0 | 1 | 2 | F0 | R0 | FP active | RP active}

Syntax Description


all	Shows the audit log from all the slots.
summary	Shows the audit log summary count from all the slots.
0	Shows the audit log for the SM-Inter-Processor slot 0.
1	Shows the audit log for the SM-Inter-Processor slot 1.
2	Shows the audit log for the SM-Inter-Processor slot 2.
F0	Shows the audit log for the Embedded-Service-Processor slot 0.
R0	Shows the audit log for the Route-Processor slot 0.
FP active	Shows the audit log for the active Embedded-Service-Processor slot.
RP active	Shows the audit log for the active Route-Processor slot.

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced on Cisco ISR 4000 series routers, Cisco CSR 1000V series routers, and Cisco 1000 ISR series routers running time-sensitive networking (TSN).
Cisco IOS XE Gibraltar 16.12.1	This command was implemented on Cisco Catalyst 9800 Series Wireless Controller.

Usage Guidelines

The show platform software audit command displays the system logs containing the access violation events.

In Cisco IOS XE Gibraltar 16.11.1, operation in a permissive mode is available - with the intent of confining specific components (process or application) of the IOS-XE platform. In the permissive mode, access violation events are detected and system logs are generated, but the event or operation itself is not blocked. The solution operates mainly in an access violation detection mode.

Examples

The following is a sample output of the show software platform software audit summary command:

Device# show platform software audit summary
===================================
AUDIT LOG ON ACTIVE
-----------------------------------
AVC Denial count: 7

Examples

The following is a sample output of the show software platform software audit all command. This command displays the information in the audit.log file.


Device# show platform software audit all
===================================
AUDIT LOG ON ACTIVE
-----------------------------------
========== START ============
type=DAEMON_START msg=audit(1553837190.262:3031): op=start ver=2.6.6 format=raw kernel=4.4.172 auid=4294967295 pid=446 subj=system_u:system_r:auditd_t:s0 res=success
type=NETFILTER_CFG msg=audit(1553837185.956:2): table=nat family=2 entries=0
type=MAC_STATUS msg=audit(1553837186.523:3): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
type=SYSCALL msg=audit(1553837186.523:3): arch=c000003e syscall=1 success=yes exit=1 a0=3 a1=7ffcf1c22070 a2=1 a3=0 items=0 ppid=203 pid=205 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="load_policy" exe="/usr/sbin/load_policy" subj=kernel key=(null)
type=PROCTITLE msg=audit(1553837186.523:3): proctitle=2F7573722F7362696E2F6C6F61645F706F6C696379002D69
type=MAC_POLICY_LOAD msg=audit(1553837186.528:4): policy loaded auid=4294967295 ses=4294967295
type=SYSCALL msg=audit(1553837186.528:4): arch=c000003e syscall=1 success=yes exit=1693637 a0=4 a1=7f792d1d6000 a2=19d7c5 a3=f items=0 ppid=203 pid=205 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="load_policy" exe="/usr/sbin/load_policy" subj=system_u:system_r:kernel_t:s0 key=(null)
…

You can use the output of this command to copy the contents of audit.log to a file to then transfer to a remote host.

Device# show platform software audit all | redirect bootflash:audi_123.log
 
Device#dir bootflash:audi_123.log
Directory of bootflash:/audi_123.log
   27  -rw-            35305  Mar 29 2019 22:16:36 +00:00  audi_123.log
 
3249049600 bytes total (538112000 bytes free)

show platform software arp broadcast

To display the Address Resolution Protocol (ARP) broadcast status on an access point (AP), use the show platform software arp broadcast command.

show platform software arp broadcast

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.8.1	This command was introduced.

Examples

The following example shows the ARP broadcast on an AP:

Device# show platform software arp broadcast

Arp broadcast is enabled on vlans:
20,50

show platform software system all

To check status of the current virtual machine and look for performance issues due to inadequate resources (or other issues with the hosting environment), use the set platform software system all command in privileged EXEC mode.

show platform software system all

Syntax Description


This command has no keywords or arguments.

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to check status of the current virtual machine and its resources:

Device# show platform software system all

Processor Details
=================
Number of Processors : 6 
Processor : 1 - 6
vendor_id : GenuineIntel
cpu MHz  : 2593.750
cache size : 35840 KB
Crypto Supported : Yes
model name : Intel(R) Xeon(R) CPU E5-2690 v4 @ 2.60GHz

Memory Details
==============
Physical Memory : 16363904KB

VNIC Details
============
Name			Mac Address		Status	Platform MTU
GigabitEthernet1	000c.2964.7126		UP	1500
GigabitEthernet2	000c.2964.7130		UP	1500

Hypervisor Details
===================
Hypervisor: VMWARE
Manufacturer: VMware, Inc.
Product Name: VMware Virtual Platform
Serial Number: VMware-56 4d e5 0a a7 dd 27 2b-0e 2f 36 6e 0f 64 71 26
UUID: 564DE50A-A7DD-272B-0E2F-366E0F647126
image_variant : 

Boot Details
===================
Boot mode: BIOS
Bootloader version: 1.1

show platform software trace filter-binary

To display the most recent trace information for a specific module, use the show platform software trace filter-binary command in privileged EXEC or user EXEC mode.

show platform software trace filter-binarymodules [ context mac-address]

Syntax Description


context`mac-address`	Represents the context used to filter. Additionally, you can filter based on module names and trace levels. The context keyword accepts either a MAC address or any other argument based on which a trace is tagged.

Command Modes

User EXEC (>)

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

This command collates and sorts all the logs present in the /tmp/.../ across all the processes relevant to the module. The trace logs of all the processes relevant to the specified module are printed to the console. This command also generates a file named collated_log_{system time} with the same content, in the /crashinfo/tracelogs directory.

Examples

This example shows how to display the trace information for a wireless module:


Device# show platform software trace filter-binary wireless

show platform software trace filter-binary

To display the most recent trace information for a specific module, use the show platform software trace filter-binary command in privileged EXEC or user EXEC mode.

show platform software trace filter-binarymodules [ context mac-address]

Syntax Description


context`mac-address`	Represents the context used to filter. Additionally, you can filter based on module names and trace levels. The context keyword accepts either a MAC address or any other argument based on which a trace is tagged.

Command Modes

User EXEC (>)

Privileged EXEC (#)

Command History


Release	Modification
	This command was introduced.

Usage Guidelines

This command collates and sorts all the logs present in the /tmp/.../ across all the processes relevant to the module. The trace logs of all the processes relevant to the specified module are printed to the console. This command also generates a file named collated_log_{system time} with the same content, in the /crashinfo/tracelogs directory.

Examples

This example shows how to display the trace information for a wireless module:


Device# show platform software trace filter-binary wireless

show platform software trace level

To view the trace levels for all the modules under a specific process, use the show platform software trace level command in privileged EXEC or user EXEC mode.

show platform software trace level wireless [ chassis { chassis-number | active | standby} R0]

Syntax Description


`process`	Process whose tracing level is being set. Options include: chassis-manager —The Chassis Manager process. cli-agent —The CLI Agent process. cmm —The CMM process. dbm —The Database Manager process. emd —The Environmental Monitoring process. fed —The Forwarding Engine Driver process. forwarding-manager —The Forwarding Manager process. geo —The Geo Manager process. host-manager —The Host Manager process. interface-manager —The Interface Manager process. iomd —The Input/Output Module daemon (IOMd) process. ios —The IOS process. license-manager —The License Manager process. logger —The Logging Manager process. platform-mgr —The Platform Manager process. pluggable-services —The Pluggable Services process. replication-mgr —The Replication Manager process. shell-manager —The Shell Manager process. sif —The Stack Interface (SIF) Manager process. smd —The Session Manager process. stack-mgr —The Stack Manager process. table-manager —The Table Manager Server. thread-test —The Multithread Manager process. virt-manager —The Virtualization Manager process. wireless —The wireless controller module process.
`slot`	Hardware slot where the process for which the trace level is set, is running. Options include: `number` —Number of the SIP slot of the hardware module where the trace level is set. For instance, if you want to specify the SIP in SIP slot 2 of the switch, enter 2. `SIP-slot / SPA-bay`—Number of the SIP switch slot and the number of the shared port adapter (SPA) bay of that SIP. For instance, if you want to specify the SPA in bay 2 of the SIP in switch slot 3, enter 3/2. F0 —The Embedded Service Processor in slot 0. F1 —The Embedded Service Processor in slot 1. FP active —The active Embedded Service Processor. R0 —The route processor in slot 0. RP active —The active route processor. switch `<number>` —The switch, with its number specified. switch active —The active switch. switch standby —The standby switch. `number` —Number of the SIP slot of the hardware module where the trace level is set. For instance, if you want to specify the SIP in SIP slot 2 of the switch, enter 2. `SIP-slot / SPA-bay`—Number of the SIP switch slot and the number of the shared port adapter (SPA) bay of that SIP. For instance, if you want to specify the SPA in bay 2 of the SIP in switch slot 3, enter 3/2. F0 —The Embedded Service Processor in slot 0. FP active —The active Embedded Service Processor. R0 —The route processor in slot 0. RP active —The active route processor.

Syntax Description


`chassis-number`	Chassis number as either 1 or 2.
active R0	Active instance of the AP filters in Route-processor slot 0.
standby R0	Standby instance of the AP filters in Route-processor slot 0.

Command Modes

User EXEC (>)

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the trace level:


Device# show platform software trace level dbm switch active R0 
Module Name                     Trace Level      
-------------------------------------------------
binos                           Notice           
binos/brand                     Notice           
bipc                            Notice           
btrace                          Notice           
bump_ptr_alloc                  Notice           
cdllib                          Notice           
chasfs                          Notice           
dbal                            Informational    
dbm                             Debug            
evlib                           Notice           
evutil                          Notice           
file_alloc                      Notice           
green-be                        Notice           
ios-avl                         Notice           
klib                            Debug            
services                        Notice           
sw_wdog                         Notice           
syshw                           Notice           
tdl_cdlcore_message             Notice           
tdl_dbal_root_message           Notice           
tdl_dbal_root_type              Notice

show platform software utd chassis active F0 et-analytics global

To view the ETA global and interface details, use the show platform software utd chassis active F0 et-analytics global command.

show platform software utd chassis active F0 et-analytics global

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the ETA global and interface details:

Device# show platform software utd chassis active F0 et-analytics global
ET Analytics Global Configuration
ID: 1
All Interfaces: Off
IP address and port and vrf: 192.168.5.2:2055:0

show platform software et-analytics global

To view the ETA global configuration, use the show platform software et-analytics global command.

Note

The show platform software et-analytics global command does not display the ETA enabled wireless client interfaces.

show platform software et-analytics global

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the ETA global and interface details:

Device# show platform software et-analytics global
ET-Analytics Global state
=========================
All Interfaces : Off
IP Flow-record Destination: 192.168.5.2 : 2055
Inactive timer: 15

show platform sudi certificate

To view the checksum record for a specific SUDI, use the show platform sudi certificate command.

show platform sudi certificate [sign [nonce nonce ]]

Syntax Description


sign	(Optional). Show signature.
`nonce`	(Optional). Enter a nonce value.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.4.1	This command was introduced.

Examples

The following example shows how to view the checksum record for the specific SUDI:

Device# show platform sudi certificate sign nonce 123
-----BEGIN CERTIFICATE-----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-----END CERTIFICATE-----
-----BEGIN CERTIFICATE-----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-----END CERTIFICATE-----
-----BEGIN CERTIFICATE-----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-----END CERTIFICATE-----
 
Signature version: 1
Signature:
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

show platform sudi pki

To validate whether a hardware unit is programmed correctly or not, use the show platform sudi pki command.

show platform sudi pki

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.7.1	This command was introduced.

Examples

The following example shows how to check whether a hardware unit is programmed correctly or not:

Device# show platform sudi pki

CMCA3 cert status : Enabled / Disabled

SUDI Issuer                          Validity status
----------------------------------------------------------------------
Cisco Manufacturing CA III           Valid / Not-valid
Cisco Manufacturing CA SHA2          Valid / Not-valid
Cisco Manufacturing CA               Valid / Not-valid

show parameter-map type umbrella global

To view the Umbrella global parameter map details, use the show parameter-map type umbrella global command.

show parameter-map type umbrella global

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the Umbrella global parameter map details:

Device# show parameter-map type umbrella global
parameter-map type umbrella global
   token   57CC80106C087FB1B2A7BAB4F2F4373C00247166
   local-domain dns_wl
   dnscrypt
   udp-timeout 2
   resolver ipv4 208.67.220.220
   resolver ipv4 208.67.222.222
   resolver ipv6 2620:119:53::53
   resolver ipv6 2620:119:35::35

show policy-map

To display quality of service (QoS) policy maps, which define classification criteria for incoming traffic, use the show policy-map command in EXEC mode.

show policy-map [policy-map-name | interface interface-id]

show policy-map interface { Auto-template|Capwap|GigabitEthernet|GroupVI|InternalInterface|Loopback|Lspvif|Null|Port-channel|TenGigabitEthernet|Tunnel|Vlan|brief|class|input|output

show policy-map interface { ap name ap_name | client mac mac_address | radio type { 24ghz | 5ghz} ap name ap_name | ssid name ssid_name { ap name ap_name | radio type { 24ghz | 5ghz} ap name ap_name}}

Syntax Description


`policy-map-name`	(Optional) Name of the policy-map.
interface `interface-id`	(Optional) Displays the statistics and the configurations of the input and output policies that are attached to the interface.
ap name `ap_name`	Displays SSID policy configuration of an access point.
client mac `mac_address`	Displays information about the policies for all the client targets.
radio type `{` 24ghz `\|` 5ghz	Displays policy configuration of the access point in the specified radio type.
ssid name `ssid_name`	Displays policy configuration of an SSID.

Command Modes

User EXEC

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

Policy maps can include policers that specify the bandwidth limitations and the action to take if the limits are exceeded.

Note

Though visible in the command-line help string, the control-plane , session , and type keywords are not supported, and the statistics shown in the display should be ignored.

To display classification counters for ternary content addressable memory (TCAM) (marking or policing) based policies, enter the interface ID. Classification counters have the following restrictions:

Classification counters are supported only on wired ports (in the ingress and egress directions).
Classification counters count packets instead of bytes.
Only QoS configurations with marking or policing trigger the classification counter.
As long as there is policing or marking action in the policy, the class-default will have classification counters.
Classification counters are not port based. The counters are shared across targets sharing the same policy map. This means that the classification counter aggregates all packets belonging to the same class of the same policy which attach to different interfaces.

Examples

This is an example of output from the show policy-map interface command, where classification counters are displayed:

Device# show policy-map interface gigabitethernet1/0/1

  GigabitEthernet1/0/1

  Service-policy input: AutoQos-4.0-CiscoPhone-Input-Policy

    Class-map: AutoQos-4.0-Voip-Data-CiscoPhone-Class (match-any)
      0 packets
      Match: cos  5
        0 packets, 0 bytes
        5 minute rate 0 bps
      QoS Set
        dscp ef
      police:
          cir 128000 bps, bc 8000 bytes
        conformed 0 bytes; actions:
          transmit
        exceeded 0 bytes; actions:
          set-dscp-transmit dscp table policed-dscp
        conformed 0000 bps, exceed 0000 bps

    Class-map: AutoQos-4.0-Voip-Signal-CiscoPhone-Class (match-any)
      0 packets
      Match: cos  3
        0 packets, 0 bytes
        5 minute rate 0 bps
      QoS Set
        dscp cs3
      police:
          cir 32000 bps, bc 8000 bytes
        conformed 0 bytes; actions:
          transmit
        exceeded 0 bytes; actions:
          set-dscp-transmit dscp table policed-dscp
        conformed 0000 bps, exceed 0000 bps

    Class-map: AutoQos-4.0-Default-Class (match-any)
      0 packets
      Match: access-group name AutoQos-4.0-Acl-Default
        0 packets, 0 bytes
        5 minute rate 0 bps
      QoS Set
        dscp default

    Class-map: class-default (match-any)
      0 packets
      Match: any
        0 packets, 0 bytes
        5 minute rate 0 bps

  Service-policy output: AutoQos-4.0-Output-Policy

    queue stats for all priority classes:
      Queueing
      priority level 1

      (total drops) 0
      (bytes output) 0

    Class-map: AutoQos-4.0-Output-Priority-Queue (match-any)
      0 packets
      Match:  dscp cs4 (32) cs5 (40) ef (46)
        0 packets, 0 bytes
        5 minute rate 0 bps
      Match: cos  5
        0 packets, 0 bytes
        5 minute rate 0 bps
      Priority: 30% (300000 kbps), burst bytes 7500000,

      Priority Level: 1

    Class-map: AutoQos-4.0-Output-Control-Mgmt-Queue (match-any)
      0 packets
      Match:  dscp cs2 (16) cs3 (24) cs6 (48) cs7 (56)
        0 packets, 0 bytes
        5 minute rate 0 bps
      Match: cos  3
        0 packets, 0 bytes
        5 minute rate 0 bps
      Queueing
      queue-limit dscp 16 percent 80
      queue-limit dscp 24 percent 90
      queue-limit dscp 48 percent 100
      queue-limit dscp 56 percent 100

      (total drops) 0
      (bytes output) 0
      bandwidth remaining 10%

      queue-buffers ratio 10

    Class-map: AutoQos-4.0-Output-Multimedia-Conf-Queue (match-any)
      0 packets
      Match:  dscp af41 (34) af42 (36) af43 (38)
        0 packets, 0 bytes
        5 minute rate 0 bps
      Match: cos  4
        0 packets, 0 bytes
        5 minute rate 0 bps
      Queueing

      (total drops) 0
      (bytes output) 0
      bandwidth remaining 10%
      queue-buffers ratio 10

    Class-map: AutoQos-4.0-Output-Trans-Data-Queue (match-any)
      0 packets
      Match:  dscp af21 (18) af22 (20) af23 (22)
        0 packets, 0 bytes
        5 minute rate 0 bps
      Match: cos  2
        0 packets, 0 bytes
        5 minute rate 0 bps
      Queueing

      (total drops) 0
      (bytes output) 0
      bandwidth remaining 10%
      queue-buffers ratio 10

    Class-map: AutoQos-4.0-Output-Bulk-Data-Queue (match-any)
      0 packets
      Match:  dscp af11 (10) af12 (12) af13 (14)
        0 packets, 0 bytes
        5 minute rate 0 bps
      Match: cos  1
        0 packets, 0 bytes
        5 minute rate 0 bps
      Queueing

      (total drops) 0
      (bytes output) 0
      bandwidth remaining 4%
      queue-buffers ratio 10

    Class-map: AutoQos-4.0-Output-Scavenger-Queue (match-any)
      0 packets
      Match:  dscp cs1 (8)
        0 packets, 0 bytes
        5 minute rate 0 bps
      Queueing

      (total drops) 0
      (bytes output) 0
      bandwidth remaining 1%
      queue-buffers ratio 10

    Class-map: AutoQos-4.0-Output-Multimedia-Strm-Queue (match-any)
      0 packets
      Match:  dscp af31 (26) af32 (28) af33 (30)
        0 packets, 0 bytes
        5 minute rate 0 bps
      Queueing

      (total drops) 0
      (bytes output) 0
      bandwidth remaining 10%
      queue-buffers ratio 10

    Class-map: class-default (match-any)
      0 packets
      Match: any
        0 packets, 0 bytes
        5 minute rate 0 bps
      Queueing

      (total drops) 0
      (bytes output) 0
      bandwidth remaining 25%
      queue-buffers ratio 25

show processes cpu

To display detailed CPU utilization statistics of IOS tasks, use the show processes cpu command.

Syntax Description


autoprofile	(Optional) Displays IOS(d) 'automatic CPUHOG profiling' information.
extended	(Optional) Displays extended CPU usage report of last 5 seconds for IOS(d) process.
history	(Optional) Displays CPU history in a graph format.
monitor	(Optional) Displays CPU utilization of IOS(d) processes continuously.
platform	(Optional) Displays CPU usage per IOS-XE process.
table	(Optional) Displays CPU history in a table format.
sorted	(Optional) Displays sorted output based on percentage of usage for IOS(d) processes.
history	(Optional) Sorts CPU utilization history. See Usage Guidelines for details.
1min	(Optional) Sorts CPU utilization based on 1-minute utilization.
5min	(Optional) Sorts CPU utilization based on 5-minute utilization.
5sec	(Optional) Sorts CPU utilization based on 5-second utilization.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.3.1	This command was integrated into Cisco IOS XE Amsterdam 17.3.1.

Usage Guidelines

If you use the history keyword, three graphs are displayed for Cisco IOS images:

CPU utilization for the last 60 seconds
CPU utilization for the last 60 minutes
CPU utilization for the last 72 hours

Maximum usage is measured and recorded every second. The average usage is calculated on periods of more than one second. Consistently high CPU utilization over an extended period indicates a problem.

To enable standby console, ensure that the following configuration is in place:

redundancy
main-cpu
secondary console enable

Examples

The following is a sample output from the show processes cpu command without keywords:

Device# show processes cpu

CPU utilization for five seconds: 0%/0%; one minute: 0%; five minutes: 0%
 PID Runtime(ms)     Invoked      uSecs   5Sec   1Min   5Min TTY Process 
  10     1576556      281188       5606  0.15%  0.05%  0.05%   0 Check heaps      
 232      845057    54261160         15  0.07%  0.05%  0.06%   0 IPAM Manager     
 595         177         300        590  0.07%  0.02%  0.01%   2 Virtual Exec     
 138     1685973   108085955         15  0.07%  0.08%  0.08%   0 L2 LISP Punt Pro 
 193       19644      348767         56  0.07%  0.00%  0.00%   0 DTP Protocol     
   5           0           1          0  0.00%  0.00%  0.00%   0 CTS SGACL db cor 
   4          24          15       1600  0.00%  0.00%  0.00%   0 RF Slave Main Th 
   6           0           1          0  0.00%  0.00%  0.00%   0 Retransmission o 
   7           0           1          0  0.00%  0.00%  0.00%   0 IPC ISSU Dispatc 
   2      117631      348801        337  0.00%  0.00%  0.00%   0 Load Meter       
   8           0           1          0  0.00%  0.00%  0.00%   0 EDDRI_MAIN       
.
.
.

show rate-limit client

To configure the rate-limit for a client on the AP, use the show rate-limit client command.

show rate-limit client

Syntax Description


This command has no arguments.

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.12.1	This command was introduced.

Examples

The following example shows how to configure the rate-limit for a client on the AP:

Device# show rate-limit client
Config:
mac vap rt_rate_out rt_rate_in rt_burst_out rt_burst_in nrt_rate_out nrt_rate_in nrt_burst_out nrt_burst_in
00:1C:F1:09:85:E7 0 8001 8002 8003 8004 8005 8006 8007 8008
Statistics:
name up down
Unshaped 0 0
Client RT pass 0 0
Client NRT pass 0 0
Client RT drops 0 0
Client NRT drops 0 0
Per client rate limit:
mac vap rate_out rate_in policy

show remote-lan all

To view the detailed output of all RLANs, use the show remote-lan all command.

show remote-lan all

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the detailed output of all RLANs:

Device# show remote-lan all
Remote-LAN Profile Name     	: rlan_test_1
================================================
Identifier                         : 1
Status                             : Enabled
Mac-filtering                      : Not Configured
Number of Active Clients           : 1
Security_8021X                     : Disabled
8021.x Authentication list name    : Not Configured
Local Auth eap Profile Name        : Not Configured
Web Auth Security                  : Disabled
Webauth Authentication list name   : Not Configured
Web Auth Parameter Map             : Not Configured
Client association limit           : 0
Ipv4 Web Pre Auth Acl              : Not Configured
Ipv6 Web Pre Auth Acl              : Not Configured

Remote-LAN Profile Name     	: rlan_test_2
================================================
Identifier                         : 2
Status                             : Enabled
Mac-filtering                      : Not Configured
Number of Active Clients           : 1
Security_8021X                     : Disabled
8021.x Authentication list name    : Not Configured
Local Auth eap Profile Name        : Not Configured
Web Auth Security                  : Disabled
Webauth Authentication list name   : Not Configured
Web Auth Parameter Map             : Not Configured
Client association limit           : 0
Ipv4 Web Pre Auth Acl              : Not Configured
Ipv6 Web Pre Auth Acl              : Not Configured

show remote-lan id

To view the RLAN configuration by ID, use the show remote-lan id command.

show remote-lan id id

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the RLAN configuration by ID:

Device# show remote-lan id <id>
Remote-LAN Profile Name     	: rlan_test_1
================================================
Identifier                                     	: 1
Status                                         	: Enabled
Mac-filtering                                  	: Not Configured
Number of Active Clients                   : 1
Security_8021X                                 	: Disabled
8021.x Authentication list name         : Not Configured
Local Auth eap Profile Name             : Not Configured
Web Auth Security                              : Disabled
Webauth Authentication list name      : Not Configured
Web Auth Parameter Map                   : Not Configured
Client association limit                       : 0
Ipv4 Web Pre Auth Acl                       : Not Configured
Ipv6 Web Pre Auth Acl                        : Not Configured

show remote-lan name

To view the RLAN configuration by profile name, use the show remote-lan name command.

show remote-lan name profile-name

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the RLAN configuration by profile name:

Device# show remote-lan name <profile-name>
Remote-LAN Profile Name     	: rlan_test_1
================================================
Identifier                         : 1
Status                             : Enabled
Mac-filtering                      : Not Configured
Number of Active Clients           : 1
Security_8021X                     : Disabled
8021.x Authentication list name    : Not Configured
Local Auth eap Profile Name        : Not Configured
Web Auth Security                  : Disabled
Webauth Authentication list name   : Not Configured
Web Auth Parameter Map             : Not Configured
Client association limit           : 0
Ipv4 Web Pre Auth Acl              : Not Configured
Ipv6 Web Pre Auth Acl              : Not Configured

show remote-lan policy detail

To view the RLAN policy profile details by profile name, use the show remote-lan policy detail command.

show remote-lan policy detail rlan_profile_name

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the RLAN policy profile details by profile name:

Device# show remote-lan policy detail <rlan_profile_name>
Profile Name                  	: rlan_named_pp1
Status                               : Enabled
Description                          : 
REMOTE-LAN ACL
  IPv4 ACL name                      : Not Configured
  IPv6 ACL name               	: Not Configured
AAA Policy Params
  AAA Override                	: Disabled
  AAA Policy name             	: default-aaa-policy
RLAN Switching policy
  Central Switching           	: Enabled
  Central Dhcp                	: Enabled
VLAN                          	: 20
Pre Authentication            	: Disabled
Session Time out              	: 1800
Violation Mode                	: REPLACE
Host Mode                     	: SINGLE_HOST_MODE
Host mode VLANs
  Voice Vlan Id               	: Not Configured
  Data Vlan Id                	: Not Configured
Exclusionlist Params
  Exclusionlist               	: Enabled
  Exclusion Timeout           	: 60
Flow Monitor IPv4
  Flow Monitor Ingress Name   	: Not Configured
  Flow Monitor Egress Name    	: Not Configured
  Flow Moniter Ingress status 	: Disabled
  Flow Moniter egress status  	: Disabled
Flow Monitor IPv6
  Flow Monitor Ingress Name   	: Not Configured
  Flow Monitor Egress Name    	: Not Configured
  Flow Moniter Ingress status 	: Disabled
  Flow Moniter egress status  	: Disabled
Split Tunnel Parameters
  Status                     	 : Disabled
  ACL name                    	: Not Configured
  Override Status             	: Disabled
  Gateway Address             	: Not Configured
  Netmask Address             	: Not Configured
DHCP
  DHCP Required               	: Disabled
  DHCP Server                 	: Not Configured
Accounting List               	: Not Configured

show remote-lan policy summary

To view the summary of policy profile for all RLANs, use the show remote-lan policy summary command.

show remote-lan policy summary

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the summary of policy profile for all RLANs:

Device# show remote-lan policy summary
Number of Policy Profiles: 1

Profile Name                      Description                             Status           
---------------------------------------------------------------------------------------------
rlan_named_pp1                 Testing RLAN policy profile                Enabled

show remote-lan summary

To view the summary of all RLANs, use the show remote-lan summary command.

show remote-lan summary

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the summary of all RLANs:

Device# show remote-lan summary
Number of RLANs: 1

RLAN  	Profile Name                      Status    
----------------------------------------------------------------
1     	rlan_test_1                       Enabled

show sdavc ap download status

To view the per access point (per-AP) download status for Software-Defined Application Visibility and Control (SD-AVC), use the show sdavc ap download status command.

show sdavc ap download status

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.7.1	This command was introduced.

Examples

The following example shows how to view the per-AP download status for SD-AVC:

Device# show sdavc ap download status 

AP  MAC         Latest filename    Status                
-----------------------------------------------------------
00d7.8f58.2f80      xyz            SUCCESS                     
00d7.8f58.2d82      abc            FAILED

show sdavc status ap

To view the Software-Defined Application Visibility and Control (SD-AVC) status for an access point (AP), use the show sdavc status ap command.

show sdavc status ap ap-name

Syntax Description


`ap-name`	AP name or MAC address.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.7.1	This command was introduced.

Examples

The following example shows how to view the SD-AVC status for an AP:


Device# show sdavc status ap 00d7.8f58.2f80

AP MAC                Status                 
------------------------------------
00d7.8f58.2f80        ENABLED

show ssh

To see the SSH connection status, use the show ssh command.

show ssh { connection-number | {vty | connection-number }}

Syntax Description


`connection-number`	SSH connection number. Valid range is 0 to 530.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the SSH connection status:

Device# show ssh connection-number

show split-tunnel client access-list

To verify split tunneling Domain Name System (DNS) Access Control Lists (ACLs) per wireless client, use the show split-tunnel client access-list command.

show split-tunnel client mac-address access-list

Syntax Description


`mac-address`	Wireless client MAC address.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.1.1	This command was introduced.

Examples

The following example shows how to verify the split tunneling DNS ACLs for a wireless client:

Device# show split-tunnel client 00:11:22:33:44:55 access-list

Split tunnel ACLs for Client: 00:11:22:33:44:55

IP ACL: SplitTunnelACL

Tunnel packets Tunnel bytes NAT packets NAT bytes
             1          242           3       768

URL ACL: SplitTunnelACL

Tunnel packets Tunnel bytes NAT packets NAT bytes
             3          778           0         0

Resolved IPs for Client: 00:11:22:33:44:55 for Split tunnel

HIT-COUNT       URL             ACTION  IP-LIST

1               base1.com       deny.   209.165.200.224
                                        209.165.200.225

2               base2.com       deny.   209.165.200.226

3               base3.com       deny.   209.165.200.227

show tech-support wireless

To display Cisco wireless LAN controller variables frequently requested by Cisco Technical Assistance Center (TAC), use the show tech-support wireless command in privileged EXEC mode.

show tech-support wireless

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following is sample output from the show tech-support wireless command:

Device# show tech-support wireless
 *** show ap capwap timers ***

Cisco AP CAPWAP timers

AP Discovery timer       : 10
AP Heart Beat timeout    : 30
Primary Discovery timer  : 120
Primed Join timeout      : 0
Fast Heartbeat           : Disabled
Fast Heartbeat timeout   : 1
*** show ap capwap retransmit ***
Global control packet retransmit interval : 3
Global control packet retransmit count : 5

AP Name                           Retransmit Interval             Retransmit Count
------------------------------------------------------------------------------------------------
TSIM_AP-2                         3                               5
TSIM_AP-3                         3                               5
*** show ap dot11 24ghz cleanair air-quality summary ***

AQ = Air Quality
DFS = Dynamic Frequency Selection

*** show ap dot11 24ghz cleanair air-quality worst ***

AQ = Air Quality
DFS = Dynamic Frequency Selection
AP Name             Channel   Avg AQ  Min AQ  Interferers  DFS
--------------------------------------------------------------
                    0         0       0       0            No
*** show ap dot11 24ghz cleanair config ***

Clean Air Solution............................... : Disabled
Air Quality Settings:
    Air Quality Reporting........................ : Disabled
    Air Quality Reporting Period (min)........... : 15
    Air Quality Alarms........................... : Enabled
    Air Quality Alarm Threshold.................. : 10
Interference Device Settings:
    Interference Device Reporting................ : Enabled
        Bluetooth Link........................... : Enabled
        Microwave Oven........................... : Enabled
        802.11 FH................................ : Enabled
        Bluetooth Discovery...................... : Enabled
        TDD Transmitter.......................... : Enabled
        Jammer................................... : Enabled
        Continuous Transmitter................... : Enabled
        DECT-like Phone.......................... : Enabled
        Video Camera............................. : Enabled
        802.15.4................................. : Enabled
        WiFi Inverted............................ : Enabled
        WiFi Invalid Channel..................... : Enabled
        SuperAG.................................. : Enabled
        Canopy................................... : Enabled
        Microsoft Device......................... : Enabled
        WiMax Mobile............................. : Enabled
        WiMax Fixed.............................. : Enabled
    Interference Device Types Triggering Alarms:
        Bluetooth Link........................... : Disabled
        Microwave Oven........................... : Disabled
        802.11 FH................................ : Disabled
        Bluetooth Discovery...................... : Disabled
        TDD Transmitter.......................... : Disabled
        Jammer................................... : Disabled
        Continuous Transmitter................... : Disabled
        DECT-like Phone.......................... : Disabled
        Video Camera............................. : Disabled
  802.15.4................................. : Disabled
        WiFi Inverted............................ : Enabled
        WiFi Invalid Channel..................... : Enabled
        SuperAG.................................. : Disabled
        Canopy................................... : Disabled
        Microsoft Device......................... : Disabled
        WiMax Mobile............................. : Disabled
        WiMax Fixed.............................. : Disabled
    Interference Device Alarms................... : Enabled
Additional Clean Air Settings:
    CleanAir Event-driven RRM State.............. : Disabled
    CleanAir Driven RRM Sensitivity.............. : LOW
    CleanAir Persistent Devices state............ : Disabled

show tech-support wireless ap

To display specific information about the Cisco APs variables frequently requested by Cisco Technical Assistance Center (TAC), use the show tech-support wireless ap command in privileged EXEC mode.

show tech-support wireless ap

Syntax Description


This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

The output of the following commands are displayed as part of show tech-support wireless apcommand:

show ap session termination statistics
show ap status
show ap tag summary
show platform software bssid chassis active F0 statistics
show platform software bssid chassis active R0 statistics
show platform software capwap chassis active F0 statistics
show platform software capwap chassis active R0 statistics
show platform software dtls chassis active F0 statistics
show platform software dtls chassis active R0 statistics
show platform software radio chassis active F0 statistics
show platform software radio chassis active R0 statistics

Examples

The following is sample output from the show tech-support wireless ap command

Device# show tech-support wireless ap

------------------ show platform software dtls chassis active R0 statistics ------------------


DTLS Counters     (Success/Failure)
-----------------------------------
Create                  0/0
Delete                  0/0

Switch 1:
OM Create               0/0
OM Delete               0/0
Ack Nack Notify         0/0


------------------ show platform software radio chassis active R0 statistics ------------------



Switch 1:
NACK Notify             0/0
  Create Failure        0
  Delete Failure        0


------------------ show platform software bssid chassis active R0 statistics ------------------



Switch 1:
NACK Notify             0/0
  Create Failure        0
  Delete Failure        0


------------------ show platform software capwap chassis active R0 statistics ------------------


Capwap Counters   (Success/Failure)
-----------------------------------
Create                  0/0
Delete                  0/0
Modify                  0/0

Switch 1:
OM Create               0/0
OM Delete               0/0
ACK-NACK Notify         0/0
  Tunnel State          0/0
  Tunnel Create         0/0
  Tunnel Modify         0/0
  Tunnel Delete         0/0


------------------ show platform software dtls chassis active F0 statistics ------------------


DTLS Counters     (Success/Failure)
-----------------------------------
Create                  0/0
Delete                  0/0
HW Create               0/0
HW Modify               0/0
HW Delete               0/0
Create Ack              0/0
Modify Ack              0/0
Delete Ack              0/0
Ack Ack Notify          0/0
Ack Nack Notify         0/0
Nack Notify             0/0
HA Seq GET              665/0
HA Seq SET              0/0
HA Seq Crypto GET       0/0
HA Seq Crypto SET       0/0
HA Seq Crypto Callback  0/0

HA Seq last Responsed   0
HA Seq Pending          0
HA Seq Outstanding cb   0
          

------------------ show platform software radio chassis active F0 statistics ------------------


Radio Counters    (Success/Failure)
-----------------------------------
Create                  0/0
Delete                  0/0
HW Create               0/0
HW Modify               0/0
HW Delete               0/0
Create Ack              0/0
Modify Ack              0/0
Delete Ack              0/0
Nack Notify             0/0


------------------ show platform software bssid chassis active F0 statistics ------------------


Bssid Counters    (Success/Failure)
-----------------------------------
Create                 0/0
Delete                 0/0
HW Create              0/0
HW Modify              0/0
HW Delete              0/0
Create Ack             0/0
Modify Ack             0/0
Delete Ack             0/0
Nack Notify            0/0


------------------ show platform software capwap chassis active F0 statistics ------------------


Capwap Counters   (Success/Failure)
-----------------------------------
Create                  0/0
Delete                  0/0
HW Create               0/0
HW Modify               0/0
HW Delete               0/0
Create Ack              0/0
Modify Ack              0/0
Delete Ack              0/0
Ack Ack Notify          0/0
Ack Nack Notify         0/0
Nack Notify             0/0


------------------ show ap auto-rf dot11 24ghz ------------------



------------------ show ap auto-rf dot11 5ghz ------------------



------------------ show ap capwap retransmit ------------------



------------------ show ap config dot11 dual-band summary ------------------



------------------ show ap config general ------------------




------------------ show ap dot11 24ghz channel ------------------


Leader Automatic Channel Assignment
  Channel Assignment Mode                    : AUTO
  Channel Update Interval                    : 600 seconds
  Anchor time (Hour of the day)              : 0
  Channel Update Contribution
    Noise                                    : Enable
    Interference                             : Enable
    Load                                     : Disable
    Device Aware                             : Disable
  CleanAir Event-driven RRM option           : Disabled
  Channel Assignment Leader                  : ewlc-doc (9.12.32.10)
  Last Run                                   : 25 seconds ago

  DCA Sensitivity Level                      : MEDIUM : 10 dB
  DCA Minimum Energy Limit                   : -95 dBm
  Channel Energy Levels
    Minimum                                  : unknown
    Average                                  : unknown
    Maximum                                  : -128 dBm
  Channel Dwell Times
    Minimum                                  : unknown
    Average                                  : unknown
          

------------------ show ap dot11 24ghz group ------------------


Radio RF Grouping

  802.11b Group Mode               : AUTO
  802.11b Group Update Interval    : 600 seconds
  802.11b Group Leader             : ewlc-doc (9.12.32.10)
  802.11b Last Run                 : 26 seconds ago


RF Group Members

Controller name                   Controller IP     
--------------------------------------------------
ewlc-doc                          9.12.32.10        




------------------ show ap dot11 24ghz load-info ------------------



------------------ show ap dot11 24ghz monitor ------------------


Default 802.11b AP monitoring
  802.11b Monitor Mode                 : Enabled
  802.11b Monitor Channels             : Country channels
  802.11b RRM Neighbor Discover Type   : Transparent
  802.11b AP Coverage Interval         : 180 seconds
  802.11b AP Load Interval             : 60 seconds
  802.11b AP Noise Interval            : 180 seconds
  802.11b AP Signal Strength Interval  : 60 seconds
  802.11b NDP RSSI Normalization       : Enabled


------------------ show ap dot11 24ghz network ------------------



802.11b Network                           : Enabled
11gSupport                                : Enabled
11nSupport                                : Enabled
802.11b/g Operational Rates
  802.11b 1M                              : Mandatory
  802.11b 2M                              : Mandatory
  802.11b 5.5M                            : Mandatory
  802.11b 11M                             : Mandatory
  802.11g 6M                              : Supported
  802.11g 9M                              : Supported
  802.11g 12M                             : Supported
  802.11g 18M                             : Supported
  802.11g 24M                             : Supported
  802.11g 36M                             : Supported
  802.11g 48M                             : Supported
  802.11g 54M                             : Supported
802.11n MCS Settings:
  MCS 0 : Supported
  MCS 1 : Supported
  MCS 2 : Supported
  MCS 3 : Supported
          

------------------ show ap dot11 24ghz profile ------------------



Default 802.11b AP performance profiles
  802.11b Global Interference threshold    : 10 %
  802.11b Global noise threshold           : -70 dBm
  802.11b Global RF utilization threshold  : 80 %
  802.11b Global throughput threshold      : 1000000 bps
  802.11b Global clients threshold         : 12 clients


------------------ show ap dot11 24ghz summary ------------------



------------------ show ap dot11 24ghz txpower ------------------


Automatic Transmit Power Assignment

Transmit Power Assignment Mode          : AUTO
Transmit Power Update Interval          : 600 seconds 
Transmit Power Threshold                : -70 dBm
Transmit Power Neighbor Count           : 3 APs
Min Transmit Power                      : -10 dBm
Max Transmit Power                      : 30 dBm
Update Contribution
    Noise                               : Enable
    Interference                        : Enable
    Load                                : Disable
    Device Aware                        : Disable
Transmit Power Assignment Leader        : ewlc-doc (9.12.32.10)
Last Run                                : 27 seconds ago


------------------ show ap dot11 5ghz channel ------------------


Leader Automatic Channel Assignment
  Channel Assignment Mode                    : AUTO
  Channel Update Interval                    : 600 seconds
  Anchor time (Hour of the day)              : 0
  Channel Update Contribution
    Noise                                    : Enable
    Interference                             : Enable
    Load                                     : Disable
    Device Aware                             : Disable
  CleanAir Event-driven RRM option           : Disabled
  Channel Assignment Leader                  : ewlc-doc (9.12.32.10)
  Last Run                                   : 27 seconds ago

  DCA Sensitivity Level                      : MEDIUM : 15 dB
  DCA 802.11n/ac Channel Width               : 20 MHz
  DCA Minimum Energy Limit                   : -95 dBm
  Channel Energy Levels
    Minimum                                  : unknown
    Average                                  : unknown
    Maximum                                  : -128 dBm
  Channel Dwell Times
    Minimum                                  : unknown
          

------------------ show ap dot11 5ghz group ------------------


Radio RF Grouping

  802.11a Group Mode               : AUTO
  802.11a Group Update Interval    : 600 seconds
  802.11a Group Leader             : ewlc-doc (9.12.32.10)
  802.11a Last Run                 : 28 seconds ago


RF Group Members

Controller name                   Controller IP     
--------------------------------------------------
ewlc-doc                          9.12.32.10        




------------------ show ap dot11 5ghz load-info ------------------



------------------ show ap dot11 5ghz monitor ------------------


Default 802.11a AP monitoring
  802.11a Monitor Mode                 : Enabled
  802.11a Monitor Channels             : Country channels
  802.11a RRM Neighbor Discover Type   : Transparent
  802.11a AP Coverage Interval         : 180 seconds
  802.11a AP Load Interval             : 60 seconds
  802.11a AP Noise Interval            : 180 seconds
  802.11a AP Signal Strength Interval  : 60 seconds
  802.11a NDP RSSI Normalization       : Enabled


------------------ show ap dot11 5ghz network ------------------



802.11a Network                           : Enabled
11nSupport                                : Enabled
  802.11a Low Band                        : Enabled
  802.11a Mid Band                        : Enabled
  802.11a High Band                       : Enabled
802.11a Operational Rates
  802.11a 6M                              : Mandatory
  802.11a 9M                              : Supported
  802.11a 12M                             : Mandatory
  802.11a 18M                             : Supported
  802.11a 24M                             : Mandatory
  802.11a 36M                             : Supported
  802.11a 48M                             : Supported
  802.11a 54M                             : Supported
802.11n MCS Settings:
  MCS 0 : Supported
  MCS 1 : Supported
  MCS 2 : Supported
  MCS 3 : Supported
  MCS 4 : Supported
  MCS 5 : Supported
          

------------------ show ap dot11 5ghz profile ------------------


Default 802.11a AP performance profiles

  802.11a Global Interference threshold          : 10 %
  802.11a Global noise threshold                 : -70 dBm
  802.11a Global RF utilization threshold        : 80 %
  802.11a Global throughput threshold            : 1000000 bps
  802.11a Global clients threshold               : 12 clients


------------------ show ap dot11 5ghz summary ------------------



------------------ show ap dot11 5ghz txpower ------------------


Automatic Transmit Power Assignment

Transmit Power Assignment Mode          : AUTO
Transmit Power Update Interval          : 600 seconds 
Transmit Power Threshold                : -70 dBm
Transmit Power Neighbor Count           : 3 APs
Min Transmit Power                      : -10 dBm
Max Transmit Power                      : 30 dBm
Update Contribution
    Noise                               : Enable
    Interference                        : Enable
    Load                                : Disable
    Device Aware                        : Disable
Transmit Power Assignment Leader        : ewlc-doc (9.12.32.10)
Last Run                                : 28 seconds ago


------------------ show ap image ------------------




------------------ show wireless stats ap join summary ------------------

Number of APs: 0

Base MAC        Ethernet MAC    AP Name                           IP Address       Status      Last Failure Type     Last Disconnect Reason
---------------------------------------------------------------------------------------------------------------------------------------------


------------------ show ap rf-profile summary ------------------



Number of RF-profiles: 6

RF Profile Name                  Band     Description                          State 
------------------------------------------------------------------------------------
Low_Client_Density_rf_5gh        5 GHz    pre configured Low Client Density rf Up    
High_Client_Density_rf_5gh       5 GHz    pre configured High Client Density r Up    
Low_Client_Density_rf_24gh       2.4 GHz  pre configured Low Client Density rf Up    
High_Client_Density_rf_24gh      2.4 GHz  pre configured High Client Density r Up    
Typical_Client_Density_rf_5gh    5 GHz    pre configured Typical Density rfpro Up    
Typical_Client_Density_rf_24gh   2.4 GHz  pre configured Typical Client Densit Up    


------------------ show ap slots ------------------



------------------ show ap summary ------------------


Number of APs: 0



------------------ show ap uptime ------------------


Number of APs: 0



------------------ show ap tag summary ------------------


Number of APs: 0



------------------ show ap status ------------------



------------------ show ap cdp neighbors ------------------


Number of neighbors: 0



------------------ show ap ap-join-profile summary ------------------



Number of AP Profiles: 1
AP Profile Name                   Description                             
------------------------------------------------------------------------
default-ap-profile                default ap profile                      


------------------ show ap link-encryption ------------------



------------------ show wireless stats ap session termination ------------------



------------------ show wireless loadbalance ap affinity wncd 0 ------------------



------------------ show wireless loadbalance ap affinity wncd 1 ------------------



------------------ show wireless loadbalance ap affinity wncd 2 ------------------



------------------ show wireless loadbalance ap affinity wncd 3 ------------------



------------------ show wireless loadbalance ap affinity wncd 4 ------------------



------------------ show wireless loadbalance ap affinity wncd 5 ------------------



------------------ show wireless loadbalance ap affinity wncd 6 ------------------



------------------ show wireless loadbalance ap affinity wncd 7 ------------------

show tech-support wireless client

To print the data related to all clients or a particular client, use the show tech-support wireless client command in privileged EXEC mode.

show tech-support wireless client

Syntax Description


mac-address	Client MAC address.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

The output of the following commands are displayed as part of show tech-support wireless client command:

show platform software wireless-client chassis active F0 statistics
show platform software wireless-client chassis active R0 statistics
show wireless client calls active
show wireless client calls rejected
show wireless client client-statistics summary
show wireless client device summary
show wireless client mac <mac-addr> details
show wireless client probing
show wireless client sleeping-client
show wireless client statistic
show wireless client steering
show wireless client summary
show wireless exclusionlist
show wireless pmk-cache

Note

The show tech-support wireless client command does not display the output of show wireless client summary detail command.

Examples

The following is sample output from the show tech-support wireless client command

Device# show tech-support wireless client

------------------ show wireless stats client summary ------------------

Number of Local Clients : 0


MAC Address    AP Name                          WLAN UpTime(secs) Rx Pkts Tx Pkts RSSI SNR  Data Retries
--------------------------------------------------------------------------------------------------------
                                                                                                        


------------------ show wireless client summary ------------------

Number of Local Clients: 0


Number of Excluded Clients: 0



------------------ show wireless client device summary ------------------



------------------ show wireless client steering ------------------


Client Steering Configuration Information
  Macro to micro transition threshold                  : -55 dBm
  Micro to Macro transition threshold                  : -65 dBm
  Micro-Macro transition minimum client count          : 3
  Micro-Macro transition client balancing window       : 3
  Probe suppression mode                               : Disabled
  Probe suppression validity window                    : 100 s 
  Probe suppression aggregate window                   : 200 ms
  Probe suppression transition aggressiveness          : 3
  Probe suppression hysteresis                         : -6 dBm

WLAN Configuration Information



------------------ show wireless client calls active ------------------



------------------ show wireless client calls rejected ------------------



------------------ show wireless client sleeping-client ------------------

Total number of sleeping-client entries: 0


------------------ show wireless client probing ------------------



------------------ show wireless client ap dot11 24ghz ------------------





------------------ show wireless client ap dot11 5ghz ------------------





------------------ show wireless pmk-cache ------------------


Number of PMK caches in total : 0

Type      Station             Entry Lifetime  VLAN Override         IP Override         Audit-Session-Id
---------------------------------------------------------------------------------------------------------


------------------ show wireless exclusionlist ------------------



------------------ show wireless country  configured ------------------



Configured Country..........................   US - United States                       
Configured Country Codes
        US  - United States                  802.11a Indoor/ 802.11b Indoor/ 802.11g Indoor 


------------------ show wireless tag rf summary ------------------



Number of RF Tags: 1

RF tag name                       Description                             
------------------------------------------------------------------------
default-rf-tag                    default RF tag                          


------------------ show platform software wireless-client chassis active R0 statistics ------------------


Client Counters   (Success/Failure)
-----------------------------------
Create                  0/0
Delete                  0/0
Modify                  0/0

Switch 1:
OM Create               0/0
OM Delete               0/0
NACK Notify             0/0
  Create Failure        0
  Modify Failure        0
  Delete Failure        0


------------------ show platform software wireless-client chassis active F0 statistics ------------------


Client Counters   (Success/Failure)
-----------------------------------
Create                  0/0
Delete                  0/0
HW Create               0/0
HW Modify               0/0
HW Delete               0/0
Create Ack              0/0
Modify Ack              0/0
Delete Ack              0/0
NACK Notify             0/0


------------------ show platform hardware chassis active qfp feature wireless wlclient cpp-client summary ------------------



------------------ show platform hardware chassis active qfp feature wireless wlclient datapath summary ------------------


Vlan   pal_if_hdl   mac            Input Uidb Output Uidb
------ ------------ -------------- ---------- -----------

show tech-support wireless datapath

To print the data related to CPP datapath, use the show tech-support wireless datapath command in privileged EXEC mode.

show tech-support wireless datapath

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

This command is available only on the platforms that have CPP datapath architecture, such as Cisco vEWLC, Cisco 9540 WLC, and Cisco 9880 WLC.

The output of the following commands are displayed as part of show tech-support wireless datapath command:

show platform hardware chassis active qfp feature wireless bssid summary
show platform hardware chassis active qfp feature wireless capwap cpp-client statistics
show platform hardware chassis active qfp feature wireless capwap cpp-client summary
show platform hardware chassis active qfp feature wireless capwap datapath statistics drop
show platform hardware chassis active qfp feature wireless capwap datapath statistics fragmentation
show platform hardware chassis active qfp feature wireless capwap datapath statistics reassembly
show platform hardware chassis active qfp feature wireless capwap datapath summary
show platform hardware chassis active qfp feature wireless dtls cpp-client statistics
show platform hardware chassis active qfp feature wireless dtls cpp-client summary
show platform hardware chassis active qfp feature wireless dtls datapath statistics
show platform hardware chassis active qfp feature wireless dtls datapath summary
show platform hardware chassis active qfp feature wireless et-analytics eta-pending-client-tree
show platform hardware chassis active qfp feature wireless et-analytics statistics
show platform hardware chassis active qfp feature wireless fqdn-filter summary
show platform hardware chassis active qfp feature wireless halo statistics
show platform hardware chassis active qfp feature wireless ipsg cpp-client statistics
show platform hardware chassis active qfp feature wireless ipsg cpp-client table ipv4 all
show platform hardware chassis active qfp feature wireless ipsg cpp-client table ipv6 all
show platform hardware chassis active qfp feature wireless ipsg datapath statistics global
show platform hardware chassis active qfp feature wireless ipsg datapath table ipv4 all
show platform hardware chassis active qfp feature wireless ipsg datapath table ipv6 all
show platform hardware chassis active qfp feature wireless mgmt-intf cpp-client summary
show platform hardware chassis active qfp feature wireless mgmt-intf datapath summary
show platform hardware chassis active qfp feature wireless punt statistics
show platform hardware chassis active qfp feature wireless wlan summary
show platform hardware chassis active qfp feature wireless wlclient cpp-client statistics
show platform hardware chassis active qfp feature wireless wlclient cpp-client summary
show platform hardware chassis active qfp feature wireless wlclient datapath statistic drop
show platform hardware chassis active qfp feature wireless wlclient datapath summary
show platform hardware chassis active qfp feature wireless wlclient datapath table dataglean all
show platform hardware chassis active qfp infrastructure punt statistics type per-cause
show platform hardware chassis active qfp statistics drop
show platform software bssid chassis active F0
show platform software bssid chassis active F0 statistics
show platform software capwap chassis active F0
show platform software capwap chassis active F0 statistics
show platform software dtls chassis active F0
show platform software dtls chassis active F0 statistics
show platform software wireless-client chassis active F0
show platform software wireless-client chassis active F0 statistics
show platform software wlan chassis active F0

In the presence of standby node, the following datapath commands are also displayed:

show platform hardware chassis standby qfp feature wireless bssid summary
show platform hardware chassis standby qfp feature wireless capwap cpp-client statistics
show platform hardware chassis standby qfp feature wireless capwap cpp-client summary
show platform hardware chassis standby qfp feature wireless capwap datapath statistics drop
show platform hardware chassis standby qfp feature wireless capwap datapath statistics fragmentation
show platform hardware chassis standby qfp feature wireless capwap datapath statistics reassembly
show platform hardware chassis standby qfp feature wireless capwap datapath summary
show platform hardware chassis standby qfp feature wireless dtls cpp-client statistics
show platform hardware chassis standby qfp feature wireless dtls cpp-client summary
show platform hardware chassis standby qfp feature wireless dtls datapath statistics
show platform hardware chassis standby qfp feature wireless dtls datapath summary
show platform hardware chassis standby qfp feature wireless halo statistics
show platform hardware chassis standby qfp feature wireless ipsg cpp-client statistics
show platform hardware chassis standby qfp feature wireless ipsg cpp-client table ipv4 all
show platform hardware chassis standby qfp feature wireless ipsg cpp-client table ipv6 all
show platform hardware chassis standby qfp feature wireless ipsg datapath statistics global
show platform hardware chassis standby qfp feature wireless ipsg datapath table ipv4 all
show platform hardware chassis standby qfp feature wireless ipsg datapath table ipv6 all
show platform hardware chassis standby qfp feature wireless mgmt-intf cpp-client summary
show platform hardware chassis standby qfp feature wireless mgmt-intf datapath summary
show platform hardware chassis standby qfp feature wireless punt statistics
show platform hardware chassis standby qfp feature wireless wlan summary
show platform hardware chassis standby qfp feature wireless wlclient cpp-client statistics
show platform hardware chassis standby qfp feature wireless wlclient cpp-client summary
show platform hardware chassis standby qfp feature wireless wlclient datapath statistic drop
show platform hardware chassis standby qfp feature wireless wlclient datapath summary
show platform hardware chassis standby qfp feature wireless wlclient datapath table dataglean all
show platform hardware chassis standby qfp statistics drop
show platform software bssid chassis standby F0
show platform software bssid chassis standby F0 statistics
show platform software capwap chassis standby F0
show platform software capwap chassis standby F0 statistics
show platform software dtls chassis standby F0
show platform software dtls chassis standby F0 statistics
show platform software wireless-client chassis standby F0
show platform software wireless-client chassis standby F0 statistics
show platform software wlan chassis standby F0

Examples

The following is sample output from the show tech-support wireless datapath command

Device# show tech-support wireless datapath 


------------------ show platform hardware chassis active qfp statistics drop ------------------

-------------------------------------------------------------------------
Global Drop Stats                         Packets                  Octets  
-------------------------------------------------------------------------  
Disabled                                    22230                 2045194  
InvL2Hdr                                  4765368               744492240  
Ipv4NoAdj                                       6                     736  
Ipv4NoRoute                                    18                    2358  
Ipv6mcNoRoute                                   3                     270  
SWPortDrop                                  14432                 2886027  
SWPortSrcFilter                             53265                53992718  
SWPortStpState                              42041                 3269790  
SWPortVlanNotCfg                          5515542               674079804  
SwitchL2m                                      78                   10062  
SwitchL2mIGMP                               18866                 1283348  
SwitchL2mUnconfigWireless                      78                   11622  
WlsCapwapNoTunnel                               3                     627  


------------------ show platform hardware chassis active qfp feature wireless punt statistics ------------------


CPP Wireless Punt stats:

                                 App Tag     Packet Count
                                 -------     ------------
         CAPWAP_PKT_TYPE_DOT11_PROBE_REQ                0
              CAPWAP_PKT_TYPE_DOT11_MGMT               56
              CAPWAP_PKT_TYPE_DOT11_IAPP            22177
              CAPWAP_PKT_TYPE_DOT11_RFID                0
               CAPWAP_PKT_TYPE_DOT11_RRM                0
             CAPWAP_PKT_TYPE_DOT11_DOT1X                0
        CAPWAP_PKT_TYPE_CAPWAP_KEEPALIVE                0
      CAPWAP_PKT_TYPE_MOBILITY_KEEPALIVE                0
            CAPWAP_PKT_TYPE_CAPWAP_CNTRL           303661
             CAPWAP_PKT_TYPE_CAPWAP_DATA                0
          CAPWAP_PKT_TYPE_MOBILITY_CNTRL                0
                         WLS_SMD_WEBAUTH                0
                       SISF_PKT_TYPE_ARP              303
                      SISF_PKT_TYPE_DHCP              282
                     SISF_PKT_TYPE_DHCP6                0
                   SISF_PKT_TYPE_IPV6_ND                0
                SISF_PKT_TYPE_DATA_GLEAN                0
             SISF_PKT_TYPE_DATA_GLEAN_V6                0
                SISF_PKT_TYPE_DHCP_RELAY                0
         CAPWAP_PKT_TYPE_CAPWAP_RESERVED                0


------------------ show platform hardware chassis active qfp infrastructure punt statistics type per-cause ------------------

Global Per Cause Statistics

  Number of punt causes =   136 

  Per Punt Cause Statistics
                                                        Packets               Packets
  Counter ID  Punt Cause Name                           Received              Transmitted           
  ------------------------------------------------------------------------------------------------  
  000         Reserved                                  0                     0                     
  001         MPLS ICMP Can't Fragment                  0                     0                     
  002         IPv4 Options                              0                     0                     
  003         Layer2 control and legacy                 0                     0                     
  004         PPP Control                               0                     0                     
  005         CLNS IS-IS Control                        0                     0                     
  006         HDLC keepalives                           0                     0                     
  007         ARP request or response                   2687                  2687                  
  008         Reverse ARP request or repsonse           0                     0                     
  009         Frame-relay LMI Control                   0                     0                     
  010         Incomplete adjacency                      0                     0                     
  011         For-us data                               0                     0                     
  012         Mcast Directly Connected Source           0                     0                     
  013         Mcast IPv4 Options data packet            0                     0                     
  014         Skip egress processing                    0                     0                     
  015         MPLS TTL expired                          0                     0                     
  016         MPLS Reserved label (ie: 0-15)            0                     0                     
  017         IPv6 Bad hop limit                        0                     0                     
  018         IPV6 Hop-by-hop Options                   0                     0                     
  019         Mcast Internal Copy                       0                     0                     
  020         Generic QFP generated packet              0                     0                     
  021         RP<->QFP keepalive                        46691                 46691                 
  022         QFP Fwall generated packet                0                     0                     
  023         Mcast IGMP Unroutable                     0                     0                     
  024         Glean adjacency                           2557                  2556                  
  025         Mcast PIM signaling                       0                     0                     
  026         QFP ICMP generated packet                 0                     0                     
  027         Subscriber session control                0                     0                     
  028         Subscriber data switching back            0                     0                     
  029         RP handled ICMP                           0                     0                     
  030         RP injected For-us data                   0                     0                     
  031         Punt adjacency                            0                     0                     
  032         SBC RTP DTMF                              0                     0                     
  033         Pseudowire VCCV control channel           0                     0                     
  034         Generic QFP generated packet (keep GPM)   0                     0                     
  035         Ethernet slow protocol (ie: LACP, OAM)    0                     0                     
  036         Ethernet OAM Loopback                     0                     0                     
  037         UNUSED                                    0                     0                     
  038         SPA IPC packet                            0                     0                     
  039         Punt and replicate                        0                     0                     
  040         PPPoE control                             0                     0                     
  041         PPPoE session                             0                     0                     
  042         L2TP control                              0                     0                     
  043         IP Subscriber control (ie: FSOL, keepali  0                     0                     
  044         L2TP session                              0                     0                     
  045         BFD control                               0                     0                     
  046         MVPN non-RPF signaling packet             0                     0                     
  047         MVPN PIM signalling packet                0                     0                     
  048         Mcast punt to RP                          0                     0                     
  049         SBC generated packet                      0                     0                     
  050         IPv6 packet                               0                     0                     
  051         DMVPN NHRP redirect                       0                     0                     
  052         PFR monitored prefix logging              0                     0                     
  053         PFR top talkers logging                   0                     0                     
  054         PFR top talkers application logging       0                     0                     
  055         For-us control                            0                     0                     
  056         RP injected for-us control                0                     0                     
  057         QFP VTCP generated packet                 0                     0                     
  058         Layer2 bridge domain data packet          0                     0                     
  059         QFP Stile generated packet                0                     0                     
  060         IP subnet or broadcast packet             167                   167                   
  061         Ethernet CFM packet                       0                     0                     
  062         Ethernet CFM notify packet                0                     0                     
  063         LISP LSB NOTIFICATION                     0                     0                     
  064         Service Engine packet                     0                     0                     
  065         L2BD Control packet from FIA              0                     0                     
  066         L2BD Control Message from CPP             0                     0                     
  067         MFR_LIP_CONTROL                           0                     0                     
  068         Media Monitoring record punted from CPP   0                     0                     
  069         OTV Control packet                        0                     0                     
  070         OTV ARP packet                            0                     0                     
  071         REP control                               0                     0                     
  072         IP MTU EXCEPTION                          0                     0                     
  073         STP BPDU's                                186832                186832                
  074         ACL log                                   0                     0                     
  075         EPC                                       0                     0                     
  076         Lisp Dynamic eid                          0                     0                     
  077         L2 Control packet                         122389                122389                
  078         WAAS CPP to CPP punt                      0                     0                     
  079         dhcp snoop                                0                     0                     
  080         Metric Mediation Agent record punted fro  0                     0                     
  081         IPv6 DMVPN NHRP redirect                  0                     0                     
  082         Ethernet CFM packet from core             0                     0                     
  083         Ethernet CFM punt fwd packet              0                     0                     
  084         PTP punt fwd packet                       0                     0                     
  085         ISDN D-Channel raw packet                 0                     0                     
  086         Service controller SCG punt pkt           0                     0                     
  087         IPv6 FHS SG dropped packet                0                     0                     
  088         IPv6 FHS Data glean packet                0                     0                     
  089         SBC DSP pkts                              0                     0                     
  090         Raw Socket Data packet                    0                     0                     
  091         SSLVPN session control                    0                     0                     
  092         ICMP unreachables for ACL denied packets  0                     0                     
  093         CENT Smart Probe packet                   0                     0                     
  094         AppNav vPATH pktless API generated pkt    0                     0                     
  095         Autonomic Network Channel Discovery pack  0                     0                     
  096         Layer2 control protocols                  0                     0                     
  097         Packets to LFTS                           22177                 22177                 
  098         VLAN Auto Sense FSOL                      0                     0                     
  099         ZTP Discovery packet                      0                     0                     
  100         cable arp filter                          0                     0                     
  101         Cable L3 mobility                         0                     0                     
  102         Source Verify inconclusive                0                     0                     
  103         cable modem pre reg                       0                     0                     
  104         mpls receive adj                          0                     0                     
  105         MKA EAPoL packet                          0                     0                     
  106         ICMP Unreachable                          0                     0                     
  107         Cable DHCP                                0                     0                     
  108         Snooping packet                           0                     0                     
  109         snoop packets                             0                     0                     
  110         msg Indicating ppp intf assigned ip addr  0                     0                     
  111         msg indicating there is another common h  0                     0                     
  112         QoS CAC Flow Report                       0                     0                     
  113         Active identity                           0                     0                     
  114         BGP Overlay Tunnel packet                 0                     0                     
  115         Lisp gsmr enabled                         0                     0                     
  116         Async TS                                  0                     0                     
  117         Metric Mediation Agent Packet             0                     0                     
  118         Cable DHCPV6 Solicit                      0                     0                     
  119         Cable DHCPV6 Request                      0                     0                     
  120         SBC RTP FWD DTMF                          0                     0                     
  121         Path Manager                              0                     0                     
  122         L2 LISP VXLAN                             0                     0                     
  123         dialer-list                               0                     0                     
  124         Dialer update time                        0                     0                     
  125         Cable RPHY CTRL                           0                     0                     
  126         OpenFlow SDN                              0                     0                     
  127         Path Manager TTL expired                  0                     0                     
  128         L3 PTP message                            0                     0                     
  129         wls 802.11 Packets to LFTS                56                    56                    
  130         wls CAPWAP Packets to LFTS                303661                303661                
  131         wls MOBILITY Packets to LFTS              0                     0                     
  132         wls SISF Packets to LFTS                  585                   585                   
  133         cable DHCPv6 subscriber-side              0                     0                     
  134         cable DHCPv4 subscriber-side              0                     0                     
  135         cable DHCPv4 sub-side disc/req            0                     0                     


  Number of inject causes = 49
                              
  Per Inject Cause Statistics 
                                                        Packets               Packets
  Counter ID  Inject Cause Name                         Received              Transmitted           
  ------------------------------------------------------------------------------------------------  
  000         RESERVED                                  0                     0                     
  001         L2 control/legacy                         3115                  3115                  
  002         QFP destination lookup                    0                     0                     
  003         QFP IPv4/v6 nexthop lookup                0                     0                     
  004         QFP generated packet                      0                     0                     
  005         QFP <->RP keepalive                       46691                 0                     
  006         QFP Fwall generated packet                0                     0                     
  007         QFP adjacency-id lookup                   0                     0                     
  008         Mcast specific inject packet              0                     0                     
  009         QFP ICMP generated packet                 0                     0                     
  010         QFP/RP->QFP Subscriber data packet        0                     0                     
  011         SBC DTMF                                  0                     0                     
  012         ARP request or response                   3637                  3637                  
  013         Ethernet OAM loopback packet              0                     0                     
  014         UNUSED                                    0                     0                     
  015         PPPoE discovery packet                    0                     0                     
  016         PPPoE session packet                      0                     0                     
  017         QFP inject for pp_index lookup            0                     0                     
  018         QFP inject replicate                      0                     0                     
  019         QFP inject PIT lookup                     0                     0                     
  020         SBC generated packets                     0                     0                     
  021         QFP VTCP generated packet                 0                     0                     
  022         QFP Stile generated packet                0                     0                     
  023         Service Engine generated packet           0                     0                     
  024         Layer2 frame to EFP                       0                     0                     
  025         Layer2 frame to BD                        0                     0                     
  026         QfP Asym Routing redirected pkt           0                     0                     
  027         Compressed packet from WAAS               0                     0                     
  028         Media (e.g. voice) associated with a ses  0                     0                     
  029         service controller scg packet             0                     0                     
  030         Packet for 14 port Serial IM              0                     0                     
  031         Subscriber generated TCP reset packet     0                     0                     
  032         Layer2 frame to INPUT EFP                 0                     0                     
  033         SSLVPN inject control                     0                     0                     
  034         injected packet from UTD SP               0                     0                     
  035         injected packet from DPSS SN              0                     0                     
  036         injected packet by AppNav vPath           0                     0                     
  037         Uncompressed packet from WAAS             0                     0                     
  038         Autonomic Network Channel Discovery pack  0                     0                     
  039         Cable Bundle Flood Inject                 0                     0                     
  040         Cable L2 unicast inject                   0                     0                     
  041         downstream jib packet                     0                     0                     
  042         switch port layer 2 control packet        6254                  6253                  
  043         Applications Injecting Pkts using LFTS    303874                303269                
  044         Enhanced ping and traceroute              0                     0                     
  045         Applications Injecting packets with SGT   0                     0                     
  046         CoPP packets from EPC_WS                  0                     0                     
  047         Async TS                                  0                     0                     
  048         Layer2 frame to VLAN                      0                     0                     


------------------ show platform hardware chassis active qfp feature wireless mgmt-intf cpp-client summary ------------------

Wireless Management Interface Info
 CPP IF_H   VLAN   MAC Address    
--------------------------------  
   0XF       78   001e.1405.2bff  


------------------ show platform hardware chassis active qfp feature wireless mgmt-intf datapath summary ------------------

Wireless Management Interface Info
IF_H       VLAN   MAC Address     
--------------------------------------
0xF        78     001e.1405.2bff      


------------------ show platform software wlan chassis active F0 ------------------


WLAN Interface ID  WLAN ID     WLAN Name                                AOM ID  Status        
--------------------------------------------------------------------------------------------  
0xf0400001         1           att                                         275  Done          
0xf0400002         2           verizon                                     292  Done          



------------------ show platform hardware chassis active qfp feature wireless wlan summary ------------------

CPP Wlan Database Summary
Total number of wlan interfaces : 2
         if_name             cpp_if_hdl    pal_if_hdl     in_uidb       out_uidb                  ssid                
--------------------------------------------------------------------------------------------------------------------  
   WLAN-IF-0x00f0400001         0X74       0XF0400001     0X1768E       0X1768C                   att                 
   WLAN-IF-0x00f0400002         0X78       0XF0400002     0X1768A       0X17688                 verizon               


------------------ show platform software bssid chassis active F0 statistics ------------------


Bssid Counters    (Success/Failure)
-----------------------------------
Create                 0/0         
Delete                 0/0         
HW Create              0/0         
HW Modify              0/0         
HW Delete              0/0         
Create Ack             0/0         
Modify Ack             0/0         
Delete Ack             0/0         
Nack Notify            0/0         


------------------ show platform software bssid chassis active F0 ------------------



------------------ show platform hardware chassis active qfp feature wireless bssid summary ------------------



------------------ show platform software capwap chassis active F0 statistics ------------------


Capwap Counters   (Success/Failure)
-----------------------------------
Create                  424/0      
Delete                  420/0      
HW Create               424/0      
HW Modify               0/0        
HW Delete               420/0      
Create Ack              424/0      
Modify Ack              0/0        
Delete Ack              420/0      
Ack Ack Notify          0/0        
Ack Nack Notify         0/0        
Nack Notify             0/0        


------------------ show platform software capwap chassis active F0 ------------------


 Tunnel ID  AP MAC          Type            IP                Port      AOM ID  Status        
--------------------------------------------------------------------------------------------  
0x90000042  00a8.2200.0200  Data            78.1.50.1        52345        3271  Done          
0xa0000002  0000.0000.0000  Mobility Data   78.1.1.23        16667        1426  Done          
0xa0000003  0000.0000.0000  Mobility Data   78.1.1.24        16667        1427  Done          
0xa0000004  0000.0000.0000  Mobility Data   78.1.1.25        16667        1428  Done          



------------------ show platform hardware chassis active qfp feature wireless capwap cpp-client statistics ------------------


CAPWAP cpp-client plumbing statistics
Number Msg in = ack + nak + ack fail + nak fail + errors

Counter                                        Value                 
-------------------------------------------------------------------  
Create from fp                                 424                   
Modify from fp                                 0                     
Delete from fp                                 420                   
Create ack to fp                               424                   
Create ack fail to fp                          0                     
Create nack to fp                              0                     
Create nack fail to fp                         0                     
Modify ack to fp                               0                     
Modify ack fail to fp                          0                     
Modify nack to fp                              0                     
Modify nack fail to fp                         0                     
Delete ack to fp                               420                   
Delete ack fail to fp                          0                     
Delete nack to fp                              0                     
Delete nak fail to fp                          0                     


------------------ show platform hardware chassis active qfp feature wireless capwap cpp-client summary ------------------

 cpp_if_hdl    pal_if_hdl       AP MAC           Src IP            Dst IP       Dst Port  Tun Type  
--------------------------------------------------------------------------------------------------  
   0X108       0X90000042   00a8.2200.0200      78.1.1.7         78.1.50.1       52345      DATA    
   0X10B       0XA0000002   0000.0000.0000      78.1.1.7         78.1.1.23       16667    MOBILITY  
   0X10C       0XA0000003   0000.0000.0000      78.1.1.7         78.1.1.24       16667    MOBILITY  
   0X10D       0XA0000004   0000.0000.0000      78.1.1.7         78.1.1.25       16667    MOBILITY  


------------------ show platform hardware chassis active qfp feature wireless capwap datapath summary ------------------


Vrf Src Port Dst IP          Dsp Port Input Uidb Output Uidb Instance Id
--- -------- ------          -------- ---------- ----------- -----------
0   16667    78.1.1.25       16667    95733      95731       0          
0   5247     78.1.50.1       52345    95738      95736       3          
0   16667    78.1.1.24       16667    95734      95732       0          
0   16667    78.1.1.23       16667    95735      95733       0          


------------------ show platform hardware chassis active qfp feature wireless capwap datapath statistics drop ------------------



Drop Cause                                                                Packets               Octets
================================================================================ ==================== 
Wls Capwap unsupported link type Error                                          0                    0
Wls Capwap invalid tunnel Error                                                 0                    0
Wls Capwap input config missing Error                                           0                    0
Wls Capwap invalid TPID Error                                                   0                    0
Wls Capwap ingress parsing Error                                                0                    0
Wls Capwap invalid FC subtype Error                                             0                    0
Wls Capwap SNAP Invalid HLEN Error                                              0                    0
Wls Client V6 Max Address Error                                                 0                    0


------------------ show platform hardware chassis active qfp feature wireless capwap datapath statistics fragmentation ------------------


CPP Wireless Fragmentation stats:

                             Description         Packet Count          Octet Count

                             -----------         ------------          -----------
 Capwap Packets to be Fragmented (RX)                       0                    0
 Capwap Fragments to be Recycled                            0                    0
 Capwap Fragments Recycled (TX)                             0                    0
 Error: Original Packet Too Big                             0                    0
 Error: CAPWAP MTU Not Valid                                0                    0
 Error: Recycle Queue Full                                  0                    0
 Error: Recycle Queue Not Valid                             0                    0
 Error: GPM Memory Init Failure                             0                    0
 Error: Multipass Requeue Failure                           0                    0


------------------ show platform hardware chassis active qfp feature wireless capwap datapath statistics reassembly ------------------


CPP Wireless Reassembly Memory stats:

                             Description            Count
                             -----------            -----
                         Free info chunk            32768
                   Allocated info chunks            32768
                    Free fragment chunks           131072
               Allocated fragment chunks           131072


CPP Wireless Reassembly Packet stats: (outstanding pkt_cnt 0) 

                             Description     Packet Count      Octet Count
                             -----------     ------------      -----------
     Capwap Reassembled Packets                         0                0
     Capwap Fragments Received                          0                0
     Capwap Fragments Consumed (Saved)                  0                0
     Capwap Fragments Dropped                           0                0
     Capwap Reassembly Timeouts                         0                0
     Error - Early-drop fragments                       0                0
     Error - Invalid packet size                        0                0
     Error - Fragment size too big                      0                0
     Error - Too many fragments                         0                0
     Error - Overlap offset fragments                   0                0
     Error - Duplicated fragments                       0                0
     Error - Allocate info chunk memory                 0                0
     Error - Allocate frag chunk memory                 0                0
     Error - Hash bucket threshold                      0                0
     Error - Cannot save and gather pkts                0                0
     Error - Get recycle reass_info NULL                0                0
     Error - BQS memory alloc NULL                      0                0
     Error - BQS memory free NULL                       0                0
     DEBUG - # of lock sync aquired                     2                2
     DEBUG - # of lock released                         2                2
     DEBUG - CPP_CW_BQS_MX_ALLOC #                      0                0
     DEBUG - CPP_CW_BQS_MX_FREE  #                      0                0
     DEBUG - CPP_REASS_INFO_ALLOC #                     0                0
     DEBUG - CPP_REASS_INFO_FREE  #                     0                0
     DEBUG - CPP_REASS_FRAG_ALLOC #                     0                0
     DEBUG - CPP_REASS_FRAG_FREE  #                     0                0


------------------ show platform software dtls chassis active F0 statistics ------------------


DTLS Counters     (Success/Failure)
-----------------------------------
Create                  847/0      
Delete                  424/0      
HW Create               425/0      
HW Modify               422/0      
HW Delete               424/0      
Create Ack              425/0      
Modify Ack              422/0      
Delete Ack              424/0      
Ack Ack Notify          1271/0     
Ack Nack Notify         0/0        
Nack Notify             0/0        
HA Seq GET              782/0      
HA Seq SET              0/0        
HA Seq Crypto GET       1542/0     
HA Seq Crypto SET       0/0        
HA Seq Crypto Callback  1542/0     

HA Seq last Responsed   0
HA Seq Pending          0
HA Seq Outstanding cb   0
Total DTLS CTX count    1


------------------ show platform software dtls chassis active F0 ------------------


Forwarding Manager DTLS Session Summary

Session ID          Type        Peer IP          Port   AOM ID      Status                  
------------------------------------------------------------------------------------------  
0x0300000000000001  AP Control  78.1.50.1        52345  3270        Done                    



------------------ show platform hardware chassis active qfp feature wireless dtls cpp-client statistics ------------------


DTLS cpp-client plumbing statistics
Number Msg in = ack + nak + ack fail + nak fail + errors

Counter                                        Value                 
-------------------------------------------------------------------  
Create from fp                                 425                   
Modify from fp                                 422                   
Delete from fp                                 424                   
Create ack to fp                               425                   
Create ack fail to fp                          0                     
Create nack to fp                              0                     
Create nack fail to fp                         0                     
Modify ack to fp                               422                   
Modify ack fail to fp                          0                     
Modify nack to fp                              0                     
Modify nack fail to fp                         0                     
Delete ack to fp                               424                   
Delete ack fail to fp                          0                     
Delete nack to fp                              0                     
Delete nak fail to fp                          0                     


------------------ show platform hardware chassis active qfp feature wireless dtls cpp-client summary ------------------

    Session ID          CDH Handle      Session Type     Parent if-h        Instance id    
-----------------------------------------------------------------------------------------  
0x0300000000000001  0x00000000D902D9E0   AP Control           0                  3         


------------------ show platform hardware chassis active qfp feature wireless dtls datapath summary ------------------


Src IP          Dst IP          Src Port Dst Port   Crypto HDL         Instance Id
------          ------          -------- -------    -----------        ---------- 
78.1.1.7        78.1.50.1       5246     52345      0xd902d9e0           3        

------------------ show platform hardware chassis active qfp feature wireless dtls datapath statistics ------------------


CPP Wireless DTLS Feature Stats

                             Description     Packet Count      Octet Count
                             -----------     ------------      -----------
   DTLS Packets To Encrypt                         286494          8860778
   DTLS Packets Encrypted                          286494         35681366
   DTLS Packets To Decrypt                         286734         41001830
   DTLS Packets Decrypted                          286734         33401602
   Skip Encryption - Handshake                          0                0
   Skip Encryption - Not AppData                        0                0
   Skip Encryption - No Hash Entry                      0                0
   Skip Encryption - No Crypto Handle                   0                0
   Skip Encryption - No DTLS header                   563            76419
   Skip Encryption - Requested by RP                16234          5042852
   Skip Decryption - Handshake                          0                0
   Skip Decryption - Not AppData                     2949           996248
   Skip Decryption - No Hash Entry                    447            56474
   Skip Decryption - No Crypto Handle               13024          3626640
   Skip Decryption - No DTLS header                   507           116600
   Skip Decryption - Multiple Records                   0                0
   Error - Encrypt Invalid Length                       0                0
   Error - Encrypt Header Restore                       0                0
   Error - DataEncrypt No Crypto Handle                 0                0
   Error - DataEncrypt Header Restore                   0                0
   Error - Decrypt Invalid Length                       0                0
   Error - Decrypt Header Restore                       0                0
   Error - DataDecrypt Zero Epoch                       0                0
   Error - DataDecrypt No Hash Entry                    0                0
   Error - DataDecrypt No Crypto Handle                 0                0
   Error - DataDecrypt Header Restore                   0                0


------------------ show platform software wireless-client chassis active F0 statistics ------------------


Client Counters   (Success/Failure)
-----------------------------------
Create                  112/0      
Delete                  55/0       
HW Create               56/0       
HW Modify               56/0       
HW Delete               55/0       
Create Ack              56/0       
Modify Ack              56/0       
Delete Ack              55/0       
NACK Notify             0/0        


------------------ show platform software wireless-client chassis active F0 ------------------


        ID  MAC Address     WLAN  Client State           AOM ID  Status        
-----------------------------------------------------------------------------  
0xa0000001  0028.b122.0001     1  Run                      3272  Done          



------------------ show platform hardware chassis active qfp feature wireless wlclient cpp-client statistics ------------------


Wlclient cpp-client plumbing statistics
Number Msg in = ack + nak + ack fail + nak fail + errors

Counter                                        Value                 
-------------------------------------------------------------------  
Create from fp                                 56                    
Modify from fp                                 56                    
Delete from fp                                 55                    
Create ack to fp                               56                    
Create ack fail to fp                          0                     
Create nack to fp                              0                     
Create nack fail to fp                         0                     
Modify ack to fp                               56                    
Modify ack fail to fp                          0                     
Modify nack to fp                              0                     
Modify nack fail to fp                         0                     
Delete ack to fp                               55                    
Delete ack fail to fp                          0                     
Delete nack to fp                              0                     
Delete nak fail to fp                          0                     


------------------ show platform hardware chassis active qfp feature wireless wlclient cpp-client summary ------------------

Auth State Abbreviations:
  UK - UNKNOWN IP - LEARN IP
  L3 - L3 AUTH RN - RUN     
  IV - INVALID              
Mobility State Abbreviations:
  UK - UNKNOWN IN - INIT     
  LC - LOCAL   AN - ANCHOR   
  FR - FOREIGN MT - MTE      
  IV - INVALID               
 CPP IF_H     DPIDX      MAC Address    VLAN  AS  MS                WLAN                    POA      
---------------------------------------------------------------------------------------------------  
  0X102     0XA0000001  0028.b122.0001  177   RN  LC                 att                 0x90000042  


------------------ show platform hardware chassis active qfp feature wireless wlclient datapath summary ------------------


Vlan   pal_if_hdl   mac            Input Uidb Output Uidb
------ ------------ -------------- ---------- -----------
177    0xa0000001   0028.b122.0001 95744      95742      


------------------ show platform hardware chassis active qfp feature wireless wlclient datapath statistic drop ------------------



Drop Cause                                                                Packets               Octets
============================================================ ==================== ====================
Wls Client V6 Max Address Error                                                 0                    0
Wls Client IPGlean Counter Index Error                                          0                    0
Wls Client IPGlean Counter Unchanged Error                                      0                    0
Wls Client IPGlean alloc no memory Error                                        0                    0
Wls Client invalid punt packet error                                            0                    0
Wls Client input subblock missing error                                         0                    0
Wls Client input config missing                                                 0                    0
Wls Client global mac address fetch error                                       0                    0
Wls Client header add error                                                     0                    0
Wls Client IP entry theft error                                                 0                    0
Wls Client IPSG input subblock missing error                                    0                    0
Wls Client DOT1Q Hdr add anchor error                                           0                    0
Wls Client DOT1Q Hdr add anchor avc error                                       0                    0
Wls Client Guest Foreign Multicast error                                        0                    0


------------------ show platform hardware chassis active qfp feature wireless wlclient datapath table dataglean all ------------------


CPP Wireless IPv6 Data Gleaning Table:

IP Address                                VLAN    uIDB   Interface
----------------------------------------  ----  ------  -------------


------------------ show platform hardware chassis active qfp feature wireless ipsg cpp-client statistics ------------------

CPP Wireless IPSG CPP-client Statistics
Counter                         Value                 
----------------------------------------------------  
Total IPv4 Address Count        1                     
Total IPv6 Address Count        0                     
IPv4 Entry Add Success          56                    
IPv4 Entry Add Fail             0                     
IPv4 Entry Delete Success       55                    
IPv4 Entry Delete Fail          0                     
IPv6 Entry Add Success          0                     
IPv6 Entry Add Fail             0                     
IPv6 Entry Delete Success       0                     
IPv6 Entry Delete Fail          0                     
IP Entry Override               0                     
IP Entry Add Req Skip           0                     
Data Glean Memory Req Recv      0                     
Data Glean Memory Req Fail      0                     
Data Glean Memory Reg Send      0                     
Data Glean Memory Ret Recv      0                     
Data Glean Memory Ret Send      0                     
Data Glean Entry Send           0                     
IPSG Subblock Allocate          0                     
IPSG Subblock Allocate Fail     0                     
IPSG Subblock Free              0                     
IPSG Subblock Free Fail         0                     
IPSG FIA Enable                 0                     
IPSG FIA Enable Fail            0                     
IPSG FIA Disable                0                     
IPSG FIA Disable Fail           0                     
IPSG Feature Enable             0                     
IPSG Feature Enable Fail        0                     
IPSG Feature Disable            0                     
IPSG Feature Disable Fail       0                     


------------------ show platform hardware chassis active qfp feature wireless ipsg cpp-client table ipv4 all ------------------

CPP Wireless IPSG Table Summary
Total number of address entries: 1
IP Address                                VLAN  uIDB   
-----------------------------------------------------  
177.1.0.7                                 177   95744  


------------------ show platform hardware chassis active qfp feature wireless ipsg cpp-client table ipv6 all ------------------

CPP Wireless IPSG Table Summary
Total number of address entries: 0


------------------ show platform hardware chassis active qfp feature wireless ipsg datapath statistics global ------------------


  Wireless IPSG Global Statistics
  ---------------------------------
    IPv6 Dataglean entry add          :  0 
    IPv6 Dataglean entry remove       :  0 
    IPv6 Dataglean allocation fail    :  0 
    IPv6 Dataglean pool req send      :  0 
    IPv6 Dataglean pool req send fail :  0 
    IPv6 Dataglean pool req resp      :  0 
    IPv6 Dataglean pool ret send      :  0 
    IPv6 Dataglean pool ret send fail :  0 
    IPv6 Dataglean punt packet        :  0 
    IPv6 Dataglean drop packet        :  0 


------------------ show platform hardware chassis active qfp feature wireless ipsg datapath table ipv4 all ------------------


CPP Wireless IPSG IPv4 Table:

IP Address                                VLAN    uIDB   Interface
----------------------------------------  ----  ------  -------------
177.1.0.7                                  177   95744  WLCLIENT-IF-0x00a0000001


------------------ show platform hardware chassis active qfp feature wireless ipsg datapath table ipv6 all ------------------


CPP Wireless IPSG IPv6 Table:

IP Address                                VLAN    uIDB   Interface
----------------------------------------  ----  ------  -------------


------------------ show platform hardware chassis active qfp feature wireless halo statistics ------------------


Wireless HALO Statistics
                         Rx Packet Count                0
                         Rx Packet Bytes                0


------------------ show platform hardware chassis active qfp feature wireless fqdn-filter summary ------------------


CPP Wireless FQDN Filter Info:
ID   Type     DSA_hdl    Redirect_IPv4    Virtual_IPv4
---- -------- ---------- ---------------- ----------------


------------------ show platform hardware chassis active qfp feature wireless et-analytics statistics ------------------


Wireless ETA cpp-client plumbing statistics
Number of ETA pending clients : 0          

Counter                                        Value                 
-------------------------------------------------------------------
Enable ETA on wireless client called           0
Delete ETA on wireless client called           0
ETA global cfg init cb TVI FIA enable error    0
ETA global cfg init cb output SB read error    0
ETA global cfg init cb output SB write error   0
ETA global cfg init cb input SB read error     0
ETA global cfg init cb input SB write error    0
ETA global cfg init cb TVI FIA enable success  0
ETA global cfg uninit cb ingress feat disable  0
ETA global cfg uninit cb ingress cfg delete e  0
ETA global cfg uninit cb egress feat disable   0
ETA global cfg uninit cb egress cfg delete er  0
ETA pending list insert entry called           0
ETA pending list insert invalid arg error      0
ETA pending list insert entry exists error     0
ETA pending list insert no memory error        0
ETA pending list insert entry failed           0
ETA pending list insert entry success          0
ETA pending list delete entry called           0
ETA pending list delete invalid arg error      0
ETA pending list delete entry missing          0
ETA pending list delete entry remove error     0
ETA pending list delete entry success          0


------------------ show platform hardware chassis active qfp feature wireless et-analytics eta-pending-client-tree ------------------

show tech-support wireless fabric

To display global fabric parameters, use the show tech-support wireless fabric command in privileged EXEC mode.

show tech-support wireless fabric

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

The output of the following commands are displayed as part of show tech-support wireless fabric command:

show wireless fabric summary
show wireless profile fabric summary
show fabric wlan summary
show fabric ap summary
show wireless fabric client summary
show wireless fabric media-stream client summary
show wireless stats fabric memory
show wireless stats fabric control-plane all

Examples

The following is sample output from the show tech-support wireless fabric command

show tech-support wireless mobility

To print the data related to mobility, use the show tech-support wireless mobility command in privileged EXEC mode.

show tech-support wireless mobility

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

The output of the following commands are displayed as part of show tech-support wireless mobility command:

show platform hardware chassis active qfp feature wireless capwap cpp-client summary
show platform hardware chassis active qfp feature wireless capwap datapath summary
show platform hardware chassis active qfp feature wireless dtls cpp-client summary
show platform hardware chassis active qfp feature wireless dtls datapath statistics
show platform hardware chassis active qfp feature wireless dtls datapath summary
show platform software capwap chassis active f0
show platform software capwap chassis active r0
show platform software dtls chassis active f0
show platform software dtls chassis active r0
show platform software ipc queue-based mobilityd chassis active R0 connection
show platform software memory messaging mobilityd chassis active R0
show platform software memory mobilityd chassis active R0 brief
show wireless mobility ap-list
show wireless mobility summary
show wireless stats mobility
show wireless stats mobility messages

In the presence of standby node, the output of the following mobility commands are also be displayed:

show platform hardware chassis standby qfp feature wireless capwap cpp-client summary
show platform hardware chassis standby qfp feature wireless capwap datapath summary
show platform hardware chassis standby qfp feature wireless dtls cpp-client summary
show platform hardware chassis standby qfp feature wireless dtls datapath statistics
show platform hardware chassis standby qfp feature wireless dtls datapath summary
show platform software capwap chassis standby f0
show platform software capwap chassis standby r0
show platform software dtls chassis standby f0
show platform software dtls chassis standby r0
show platform software ipc queue-based mobilityd chassis standby R0 connection
show platform software memory messaging mobilityd chassis standby R0
show platform software memory mobilityd chassis standby R0 brief
show wireless stats mobility messages chassis standby r0

Examples

The following is sample output from the show tech-support wireless mobility command

Device# show tech-support wireless mobility 

------------------ show wireless stats mobility ------------------



Mobility event statistics:
     Joined as
         Local                         : 0               
         Foreign                       : 0               
         Export foreign                : 0               
         Export anchor                 : 0               
     Delete
         Local                         : 0               
         Remote                        : 0               
     Role changes
         Local to anchor               : 0               
         Anchor to local               : 0               
     Roam stats
         L2 roam count                 : 0               
         L3 roam count                 : 0               
         Flex client roam count        : 0               
         Inter-WNCd roam count         : 0               
         Intra-WNCd roam count         : 0               
     Anchor Request
         Sent                          : 0               
           Grant received              : 0               
           Deny received               : 0               
         Received                      : 0               
           Grant sent                  : 0               
           Deny  sent                  : 0               
     Handoff Status Received
         Success                       : 0               
         Group mismatch                : 0               
         Client unknown                : 0               
         Client blacklisted            : 0
         SSID mismatch                 : 0               
         Denied                        : 0               
     Handoff Status Sent
         Success                       : 0               
         Group mismatch                : 0               
         Client unknown                : 0               
         Client blacklisted            : 0
         SSID mismatch                 : 0               
         Denied                        : 0               
     Export Anchor
         Request Sent                  : 0               
         Response Received             :      
             Ok                        : 0               
             Deny - generic            : 0               
             Client blacklisted        : 0               
             Client limit reached      : 0               
             Profile mismatch          : 0               
             Deny - unknown reason     : 0               
         Request Received              : 0               
         Response Sent                 :      
             Ok                        : 0               
             Deny - generic            : 0               
             Client blacklisted        : 0               
             Client limit reached      : 0               
             Profile mismatch          : 0               
MM mobility event statistics:
     Event data allocs                 : 0               
     Event data frees                  : 0               
     FSM set allocs                    : 0               
     FSM set frees                     : 0               
     Timer allocs                      : 0               
     Timer frees                       : 0               
     Timer starts                      : 0               
     Timer stops                       : 0               
     Invalid events                    : 0               
     Internal errors                   : 0               


MMIF mobility event statistics:
     Event data allocs                 : 0               
     Event data frees                  : 0               
     Invalid events                    : 0               
     Unkown events                     : 0               
     Event schedule errors             : 0               
     Internal errors                   : 0               



------------------ show wireless stats mobility messages ------------------


          
MM datagram message statistics:
  Message Type               Built  Tx    Rx    Processed  Tx Error  Rx Error  Forwarded  Retry  Drops  Allocs  Frees
  ----------------------------------------------------------------------------------------------------------------------
  Mobile Announce            0      0     0     0          0         0         0          0      0      0       0
  Mobile Announce Nak        0      0     0     0          0         0         0          0      0      0       0
  Static IP Mobile Annc      0      0     0     0          0         0         0          0      0      0       0
  Static IP Mobile Annc Rsp  0      0     0     0          0         0         0          0      0      0       0
  Handoff                    0      0     0     0          0         0         0          0      0      0       0
  Handoff End                0      0     0     0          0         0         0          0      0      0       0
  Handoff End Ack            0      0     0     0          0         0         0          0      0      0       0
  Anchor Req                 0      0     0     0          0         0         0          0      0      0       0
  Anchor Grant               0      0     0     0          0         0         0          0      0      0       0
  Anchor Xfer                0      0     0     0          0         0         0          0      0      0       0
  Anchor Xfer Ack            0      0     0     0          0         0         0          0      0      0       0
  Export Anchor Req          0      0     0     0          0         0         0          0      0      0       0
  Export Anchor Rsp          0      0     0     0          0         0         0          0      0      0       0
  AAA Handoff                0      0     0     0          0         0         0          0      0      0       0
  AAA Handoff Ack            0      0     0     0          0         0         0          0      0      0       0
  IPv4 Addr Update           0      0     0     0          0         0         0          0      0      0       0
  IPv4 Addr Update Ack       0      0     0     0          0         0         0          0      0      0       0
  IPv6 ND Packet             0      0     0     0          0         0         0          0      0      0       0
  IPv6 Addr Update           0      0     0     0          0         0         0          0      0      0       0
  IPv6 Addr Update Ack       0      0     0     0          0         0         0          0      0      0       0
  Client Add                 0      0     0     0          0         0         0          0      0      0       0
  Client Delete              0      0     0     0          0         0         0          0      0      0       0
  Keepalive Ctrl Req         0      0     0     0          0         0         0          0      0      0       0
  Keepalive Ctrl Resp        0      0     0     0          0         0         0          0      0      0       0
  AP List Update             0      0     0     0          0         0         0          0      0      0       0
  Client Device Profile Info 0      0     0     0          0         0         0          0      0      0       0
  PMK Update                 0      0     0     0          0         0         0          0      0      0       0
  PMK Delete                 0      0     0     0          0         0         0          0      0      0       0
  PMK 11r Nonce Update       0      0     0     0          0         0         0          0      0      0       0
  Device cache Update        0      0     0     0          0         0         0          0      0      0       0
  HA SSO Announce            0      0     0     0          0         0         0          0      0      0       0
  HA SSO Announce Resp       0      0     0     0          0         0         0          0      0      0       0

MM IPC message statistics:
  Message Type               Built  Tx    Rx    Processed  Tx Error  Rx Error  Forwarded  Drops  Allocs  Frees
  ---------------------------------------------------------------------------------------------------------------
  Mobile Announce            0      0     0     0          0         0         0          0      0       0
  Mobile Announce Nak        0      0     0     0          0         0         0          0      0       0
  Static IP Mobile Annc      0      0     0     0          0         0         0          0      0       0
  Static IP Mobile Annc Rsp  0      0     0     0          0         0         0          0      0       0
  Handoff                    0      0     0     0          0         0         0          0      0       0
  Handoff End                0      0     0     0          0         0         0          0      0       0
  Handoff End Ack            0      0     0     0          0         0         0          0      0       0
  Anchor Req                 0      0     0     0          0         0         0          0      0       0
  Anchor Grant               0      0     0     0          0         0         0          0      0       0
  Anchor Xfer                0      0     0     0          0         0         0          0      0       0
  Anchor Xfer Ack            0      0     0     0          0         0         0          0      0       0
  Export Anchor Req          0      0     0     0          0         0         0          0      0       0
  Export Anchor Rsp          0      0     0     0          0         0         0          0      0       0
  AAA Handoff                0      0     0     0          0         0         0          0      0       0
  AAA Handoff Ack            0      0     0     0          0         0         0          0      0       0
  IPv4 Addr Update           0      0     0     0          0         0         0          0      0       0
  IPv4 Addr Update Ack       0      0     0     0          0         0         0          0      0       0
  IPv6 ND Packet             0      0     0     0          0         0         0          0      0       0
  IPv6 Addr Update           0      0     0     0          0         0         0          0      0       0
  IPv6 Addr Update Ack       0      0     0     0          0         0         0          0      0       0
  Client Add                 0      0     0     0          0         0         0          0      0       0
  Client Delete              0      0     0     0          0         0         0          0      0       0
  Keepalive Ctrl Req         0      0     0     0          0         0         0          0      0       0
  Keepalive Ctrl Resp        0      0     0     0          0         0         0          0      0       0
  AP List Update             0      0     0     0          0         0         0          0      0       0
  Client Device Profile Info 0      0     0     0          0         0         0          0      0       0
  PMK Update                 0      0     0     0          0         0         0          0      0       0
  PMK Delete                 0      0     0     0          0         0         0          0      0       0
  PMK 11r Nonce Update       0      0     0     0          0         0         0          0      0       0
  Device cache Update        0      0     0     0          0         0         0          0      0       0
  HA SSO Announce            0      0     0     0          0         0         0          0      0       0
  HA SSO Announce Resp       0      0     0     0          0         0         0          0      0       0

MMIF IPC message statistics:
  Message Type               Built  Tx    Rx    Processed  Tx Error  Rx Error  Drops  Allocs  Frees
  ----------------------------------------------------------------------------------------------------
  Mobile Announce            0      0     0     0          0         0         0      0       0
  Mobile Announce Nak        0      0     0     0          0         0         0      0       0
  Static IP Mobile Annc      0      0     0     0          0         0         0      0       0
  Static IP Mobile Annc Rsp  0      0     0     0          0         0         0      0       0
  Handoff                    0      0     0     0          0         0         0      0       0
  Handoff End                0      0     0     0          0         0         0      0       0
  Handoff End Ack            0      0     0     0          0         0         0      0       0
  Anchor Req                 0      0     0     0          0         0         0      0       0
  Anchor Grant               0      0     0     0          0         0         0      0       0
  Anchor Xfer                0      0     0     0          0         0         0      0       0
  Anchor Xfer Ack            0      0     0     0          0         0         0      0       0
  Export Anchor Req          0      0     0     0          0         0         0      0       0
  Export Anchor Rsp          0      0     0     0          0         0         0      0       0
  AAA Handoff                0      0     0     0          0         0         0      0       0
  AAA Handoff Ack            0      0     0     0          0         0         0      0       0
  IPv4 Addr Update           0      0     0     0          0         0         0      0       0
  IPv4 Addr Update Ack       0      0     0     0          0         0         0      0       0
  IPv6 ND Packet             0      0     0     0          0         0         0      0       0
  IPv6 Addr Update           0      0     0     0          0         0         0      0       0
  IPv6 Addr Update Ack       0      0     0     0          0         0         0      0       0
  Client Add                 0      0     0     0          0         0         0      0       0
  Client Delete              0      0     0     0          0         0         0      0       0
  Keepalive Ctrl Req         0      0     0     0          0         0         0      0       0
  Keepalive Ctrl Resp        0      0     0     0          0         0         0      0       0
  AP List Update             0      0     0     0          0         0         0      0       0
  Client Device Profile Info 0      0     0     0          0         0         0      0       0
  PMK Update                 0      0     0     0          0         0         0      0       0
  PMK Delete                 0      0     0     0          0         0         0      0       0
  PMK 11r Nonce Update       0      0     0     0          0         0         0      0       0
  Device cache Update        0      0     0     0          0         0         0      0       0
  HA SSO Announce            0      0     0     0          0         0         0      0       0
  HA SSO Announce Resp       0      0     0     0          0         0         0      0       0


------------------ show wireless mobility summary ------------------


Mobility Summary

Wireless Management VLAN: 32
Wireless Management IP Address: 9.12.32.10
Mobility Control Message DSCP Value: 48
Mobility Keepalive Interval/Count: 10/3
Mobility Group Name: default
Mobility Multicast Ipv4 address: 0.0.0.0
Mobility Multicast Ipv6 address: ::
Mobility MAC Address: 001e.f6c1.f6ff

Controllers configured in the Mobility Domain:

 IP               Public Ip         Group Name                       Multicast IPv4    Multicast IPv6                                Status                       PMTU 
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------
9.12.32.10        N/A               default                          0.0.0.0           ::                                            N/A                          N/A
          

------------------ show wireless mobility ap-list ------------------



------------------ show platform software capwap chassis active r0 ------------------



------------------ show platform software capwap chassis active f0 ------------------



------------------ show platform software dtls chassis active r0 ------------------



------------------ show platform software dtls chassis active f0 ------------------



------------------ show platform hardware chassis active qfp feature wireless capwap cpp-client summary ------------------



------------------ show platform hardware chassis active qfp feature wireless dtls cpp-client summary ------------------



------------------ show platform hardware chassis active qfp feature wireless capwap datapath summary ------------------


Vrf Src Port Dst IP          Dsp Port Input Uidb Output Uidb Instance Id
--- -------- ------          -------- ---------- ----------- -----------


------------------ show platform hardware chassis active qfp feature wireless dtls datapath statistics ------------------


CPP Wireless DTLS Feature Stats

                             Description     Packet Count      Octet Count
                             -----------     ------------      -----------
   DTLS Packets To Encrypt                              0                0
   DTLS Packets Encrypted                               0                0
   DTLS Packets To Decrypt                              0                0
   DTLS Packets Decrypted                               0                0
   Skip Encryption - Handshake                          0                0
   Skip Encryption - Not AppData                        0                0
   Skip Encryption - No Hash Entry                      0                0
   Skip Encryption - No Crypto Handle                   0                0
   Skip Encryption - No DTLS header                     0                0
   Skip Encryption - Requested by RP                    0                0
   Skip Decryption - Handshake                          0                0
   Skip Decryption - Not AppData                        0                0
   Skip Decryption - No Hash Entry                      0                0
   Skip Decryption - No Crypto Handle                   0                0
   Skip Decryption - No DTLS header                     0                0
   Skip Decryption - Multiple Records                   0                0
   Error - Encrypt Invalid Length                       0                0
   Error - Encrypt Header Restore                       0                0
   Error - DataEncrypt No Crypto Handle                 0                0
   Error - DataEncrypt Header Restore                   0                0
   Error - Decrypt Invalid Length                       0                0
   Error - Decrypt Header Restore                       0                0
   Error - DataDecrypt Zero Epoch                       0                0
   Error - DataDecrypt No Hash Entry                    0                0
   Error - DataDecrypt No Crypto Handle                 0                0
   Error - DataDecrypt Header Restore                   0                0


------------------ show platform hardware chassis active qfp feature wireless dtls datapath summary ------------------


Src IP          Dst IP          Src Port Dst Port   Crypto HDL         Instance Id
------          ------          -------- -------    -----------        ----------

------------------ show platform software ipc queue-based mobilityd chassis active R0 connection ------------------

Name: -mobilityd_to_wncd-b0
  Number     : 0
  Mode       : writer
  Created on : 03/22/18 05:35:06
  Queue Size : 524288 bytes, 0 bytes currently used
  Enqueued   : 12 msgs, 432 bytes, 0 err, 0 back-pressures,
               360 bytes max queue utilization,
               0 times reached above 90%, 0 times reached above 75%

Name: -mobilityd_to_wncd-b1
  Number     : 1
  Mode       : writer
  Created on : 03/22/18 05:35:06
  Queue Size : 524288 bytes, 0 bytes currently used
  Enqueued   : 12 msgs, 432 bytes, 0 err, 0 back-pressures,
               360 bytes max queue utilization,
               0 times reached above 90%, 0 times reached above 75%

Name: -mobilityd_to_wncd-b2
  Number     : 2
  Mode       : writer
  Created on : 03/22/18 05:35:06
  Queue Size : 524288 bytes, 0 bytes currently used
  Enqueued   : 12 msgs, 432 bytes, 0 err, 0 back-pressures,
               360 bytes max queue utilization,
               0 times reached above 90%, 0 times reached above 75%

Name: -mobilityd_to_fman_rp-b0
  Number     : 3
  Mode       : writer
  Created on : 03/22/18 05:35:06
  Queue Size : 524288 bytes, 0 bytes currently used
  Enqueued   : 0 msgs, 0 bytes, 0 err, 0 back-pressures,
               0 bytes max queue utilization,
               0 times reached above 90%, 0 times reached above 75%

Name: -mobilityd_to_iosd_rp-b0
  Number     : 4
  Mode       : writer
  Created on : 03/22/18 05:35:06
  Queue Size : 524288 bytes, 0 bytes currently used
  Enqueued   : 204647 msgs, 15757819 bytes, 0 err, 0 back-pressures,
               81 bytes max queue utilization,
               0 times reached above 90%, 0 times reached above 75%

Name: -mobilityd_to_wncmgrd-b0
  Number     : 5
  Mode       : writer
  Created on : 03/22/18 05:35:06
  Queue Size : 524288 bytes, 0 bytes currently used
  Enqueued   : 12 msgs, 432 bytes, 0 err, 0 back-pressures,
               360 bytes max queue utilization,
               0 times reached above 90%, 0 times reached above 75%

Name: -odm_clnt2svr_data-mobilityd-000-1
  Number     : 6
  Mode       : writer
  Created on : 03/22/18 05:35:06
  Queue Size : 2097152 bytes, 0 bytes currently used
  Enqueued   : 33 msgs, 12535 bytes, 0 err, 0 back-pressures,
               3769 bytes max queue utilization,
               0 times reached above 90%, 0 times reached above 75%

Name: -odm_svr2clnt_data-mobilityd-000-1
  Number     : 7
  Mode       : reader
  Created on : 03/22/18 05:35:06
  Queue Size : 2097152 bytes, 0 bytes currently used
  Dequeued   : 0 msgs, 0 bytes, 0 err
          
Name: -fman_rp_to_mobilityd-b0
  Number     : 8
  Mode       : reader
  Created on : 03/22/18 05:35:08
  Queue Size : 524288 bytes, 0 bytes currently used
  Dequeued   : 0 msgs, 0 bytes, 0 err

Name: -wncd_to_mobilityd-b0
  Number     : 9
  Mode       : reader
  Created on : 03/22/18 05:35:13
  Queue Size : 524288 bytes, 0 bytes currently used
  Dequeued   : 39 msgs, 1404 bytes, 0 err

Name: -wncd_to_mobilityd-b1
  Number     : 10
  Mode       : reader
  Created on : 03/22/18 05:35:13
  Queue Size : 524288 bytes, 0 bytes currently used
  Dequeued   : 39 msgs, 1404 bytes, 0 err

Name: -wncd_to_mobilityd-b2
  Number     : 11
  Mode       : reader
  Created on : 03/22/18 05:35:14
  Queue Size : 524288 bytes, 0 bytes currently used
  Dequeued   : 39 msgs, 1404 bytes, 0 err

Name: -wncmgrd_to_mobilityd-b0
  Number     : 12
  Mode       : reader
  Created on : 03/22/18 05:35:14
  Queue Size : 524288 bytes, 0 bytes currently used
  Dequeued   : 18 msgs, 648 bytes, 0 err

Name: -iosd_rp_to_mobilityd-b0
  Number     : 13
  Mode       : reader
  Created on : 03/22/18 05:35:30
  Queue Size : 1048576 bytes, 0 bytes currently used
  Dequeued   : 204647 msgs, 18827524 bytes, 0 err

Name: -odm_clnt2svr_data-ifid-005-1
  Number     : 14
  Mode       : writer
  Created on : 03/22/18 05:35:37
  Queue Size : 2097152 bytes, 0 bytes currently used
  Enqueued   : 0 msgs, 0 bytes, 0 err, 0 back-pressures,
               0 bytes max queue utilization,
               0 times reached above 90%, 0 times reached above 75%

Name: -odm_svr2clnt_data-ifid-005-1
  Number     : 15
  Mode       : reader
  Created on : 03/22/18 05:35:37
  Queue Size : 2097152 bytes, 0 bytes currently used
  Dequeued   : 0 msgs, 0 bytes, 0 err



------------------ show platform software memory messaging mobilityd chassis active R0 ------------------

[tdl_toc] type toc_table_info/47da701cd9c36de7e888ca6d8dd80390/0 created:3 destroyed:3 diff:0
[tdl_sr] type repl_table_name/29184a6d15c1ba11acb2d0bd22eb6e36/0 created:33 destroyed:33 diff:0
[tdl_sr] type repl_database_name/e9118a691a20b4b8f1118bc37a894603/0 created:33 destroyed:33 diff:0
[tdl_sr] type repl_pkey_tdl/83de2d20ec3ca19b8ae9a89147480a25/1 created:33 destroyed:33 diff:0
[tdl_sr] type repl_blob_tdl/016a67083ea407334130436c855ae237/0 created:33 destroyed:33 diff:0
[tdl_sr] type repl_luid/b9c9d9f4876af528cb82273df98479d6/0 created:33 destroyed:33 diff:0
[tdl_sr] type repl_objinfo/6c8800fedf8d71512f9b6c9754db3a70/0 created:33 destroyed:33 diff:0
[tdl_sr] message repl_trec_update/15fe2a39409473179c9e7111851b2196/0 created:33 destroyed:33 diff:0
[pki_ssl] type buff/941d8a519d6f23d27067617119f1bb38/0 created:613944 destroyed:613944 diff:0
[pki_ssl] type get_certid_params/0d7bcce690f74649c2e33bbf341e2229/0 created:204648 destroyed:204648 diff:0
[pki_ssl] type get_certid_callback_params/708b7fb964ace7971d90a452c830488c/0 created:204648 destroyed:204648 diff:0
[pki_ssl] message get_certid/ee3bfe6b93901440346417a4ad67fa63/0 created:204648 destroyed:204648 diff:0
[pki_ssl] message get_certid_callback/372218059d7a753ba73f7b06f18532e9/0 created:204648 destroyed:204648 diff:0
[svc_defs] type svc_loc/929237802cf26e862f8e8716169e31ef/0 created:40952 destroyed:40951 diff:1
[ui_shr] type ui_client/bec7457db0c33cae9eeebbf80073b771/0 created:3 destroyed:2 diff:1
[ui] type ui_info/4b8b42a883fabbb98ec8b919f60e4ad6/0 created:40949 destroyed:40949 diff:0
[ui] type ui_req/69f1e2a5943e050f0aa12df8639ba442/0 created:3 destroyed:2 diff:1
[ui] type event_statistics/7f346ee47165c035a72e139b84afb2a0/0 created:40948 destroyed:40948 diff:0
[ui] type hostinfo_data/54d5a8b0cd4d29d575b2fc0d91695b5e/0 created:3 destroyed:3 diff:0
[ui] message ui_info_msg/bec533dd713e0222cb8fe5df868031f0/0 created:1 destroyed:1 diff:0
[ui] message ui_req_msg/ac9905cc4488c976847affab56d8b50c/0 created:3 destroyed:2 diff:1
[ui] message process_event_statistics/65d07aa3a04ad950cddd46444df6bc02/0 created:40948 destroyed:40948 diff:0
[ui] message hostinfo_notify/2e9d975712b85b41bc489a6adbc4a46c/0 created:3 destroyed:3 diff:0
[uipeer_comm_ui] type mqipc_enqueue_stats/8f41e408c97a799a5e431d2279acd8de/0 created:8 destroyed:8 diff:0
[uipeer_comm_ui] type mqipc_dequeue_stats/aafe5d0a37ba9652d68550efa26eb0b6/0 created:8 destroyed:8 diff:0
[uipeer_comm_ui] type mqipc_connection_properties/35bd274fd85f7359066f898f25c853ee/0 created:16 destroyed:16 diff:0
[uipeer_comm_ui] message mqipc_connection/a1b22c74b279335b895531ce708c804b/0 created:16 destroyed:16 diff:0
[mem_stats_ui] type tdl_variant_stat/bd85e4b89fb10501e68c1a3cedb9f321/0 created:1 destroyed:0 diff:1
[mem_stats_ui] message tdl_mem_stats/60ffd9d51213767d041b543869df15d2/0 created:1 destroyed:0 diff:1
[cdlcore] type cdl_params/a3e74327d37abf27f799f2b5155f4923/0 created:2 destroyed:1 diff:1
[cdlcore] message cdl_message/35205e535c7ab2cdcb3c265ac788f973/0 created:2 destroyed:1 diff:1
[odm_defs] type odm_context/73aeecb77a1ccb6e44f690745cdafe0d/1 created:23 destroyed:23 diff:0
[odm_defs] type odm_register_info/48a7d590e9df0cc9d150801315c50307/1 created:4 destroyed:4 diff:0
[odm_defs] type odm_table_register_info/4f355a34615affd49af9f90b679d8ce5/1 created:17 destroyed:17 diff:0
[odm_defs] type odm_register_result/53ba304bc0a71a7d2a044518c21f662a/0 created:2 destroyed:2 diff:0
[odm_defs] message odm_register/2c98272b43d973fa08bbf5acdf3106b0/0 created:2 destroyed:2 diff:0
[odm_defs] message odm_table_register/46694ec1005c3b084337748eeb3768cd/0 created:17 destroyed:17 diff:0
[odm_defs] message odm_register_done/1f6c8f81fcbb8a3052428bab7588e8b5/0 created:2 destroyed:2 diff:0
[odm_defs] message odm_register_ack/03b8040ed4f7b03517b410c32568ecaa/0 created:2 destroyed:2 diff:0


------------------ show platform software memory mobilityd chassis active R0 brief ------------------

  module                  allocated     requested     allocs        frees         
  ------------------------------------------------------------------------------
  Summary                 620441        617113        233           25            
  unknown                 198515        198435        5             0             
  chunk                   139689        139209        30            0             
  eventutil               118939        118299        48            8             
  process                 67642         67594         3             0             
  odm-db-ctx              29950         28430         100           5             
  uipeer                  22672         22592         11            6             
  odm-ipc-ctx             20272         19984         18            0             
  unknown                 18024         18008         1             0             
  odm-client-ctx          1872          1824          3             0             
  cdllib                  1688          1672          3             2             
  trccfg                  512           496           5             4             
  bidb                    472           456           1             0             
  unknown                 96            48            3             0             
  bcrdu_avl               72            56            1             0             
  orchestrator_main       26            10            1             0

show tech-support wireless radio

To print the data related to the radio, use the show tech-support wireless radio command in privileged EXEC mode.

show tech-support wireless radio

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

The output of the following commands are displayed as part of show tech-support wireless radio command:

show ap auto-rf dot11 24ghz
show ap auto-rf dot11 5ghz
show ap config dot11 dual-band summary
show ap config general
show ap dot11 24ghz channel
show ap dot11 24ghz coverage
show ap dot11 24ghz group
show ap dot11 24ghz high-density
show ap dot11 24ghz load-info
show ap dot11 24ghz monitor
show ap dot11 24ghz network
show ap dot11 24ghz summary
show ap dot11 24ghz txpower
show ap dot11 5ghz channel
show ap dot11 5ghz coverage
show ap dot11 5ghz group
show ap dot11 5ghz high-density
show ap dot11 5ghz load-info
show ap dot11 5ghz monitor
show ap dot11 5ghz network
show ap dot11 5ghz summary
show ap dot11 5ghz txpower
show ap fra
show ap rf-profile name Rf1 detail
show ap rf-profile summary
show ap summary
show wireless band-select

Examples

The following is sample output from the show tech-support wireless radio command

Device# show tech-support wireless radio 

------------------ show ap summary ------------------


Number of APs: 0



------------------ show ap dot11 24ghz summary ------------------



------------------ show ap dot11 5ghz summary ------------------



------------------ show ap config dot11 dual-band summary ------------------



------------------ show ap dot11 24ghz channel ------------------


Leader Automatic Channel Assignment
  Channel Assignment Mode                    : AUTO
  Channel Update Interval                    : 600 seconds
  Anchor time (Hour of the day)              : 0
  Channel Update Contribution
    Noise                                    : Enable
    Interference                             : Enable
    Load                                     : Disable
    Device Aware                             : Disable
  CleanAir Event-driven RRM option           : Disabled
  Channel Assignment Leader                  : ewlc-doc (9.12.32.10)
  Last Run                                   : 550 seconds ago

  DCA Sensitivity Level                      : MEDIUM : 10 dB
  DCA Minimum Energy Limit                   : -95 dBm
  Channel Energy Levels
    Minimum                                  : unknown
    Average                                  : unknown
    Maximum                                  : -128 dBm
  Channel Dwell Times
    Minimum                                  : unknown
    Average                                  : unknown
    Maximum                                  : unknown
  802.11b 2.4 GHz Auto-RF Channel List
    Allowed Channel List                     : 1,6,11
    Unused Channel List                      : 2,3,4,5,7,8,9,10


------------------ show ap dot11 5ghz channel ------------------


Leader Automatic Channel Assignment
  Channel Assignment Mode                    : AUTO
  Channel Update Interval                    : 600 seconds
  Anchor time (Hour of the day)              : 0
  Channel Update Contribution
    Noise                                    : Enable
    Interference                             : Enable
    Load                                     : Disable
    Device Aware                             : Disable
  CleanAir Event-driven RRM option           : Disabled
  Channel Assignment Leader                  : ewlc-doc (9.12.32.10)
  Last Run                                   : 552 seconds ago

  DCA Sensitivity Level                      : MEDIUM : 15 dB
  DCA 802.11n/ac Channel Width               : 20 MHz
  DCA Minimum Energy Limit                   : -95 dBm
  Channel Energy Levels
    Minimum                                  : unknown
    Average                                  : unknown
    Maximum                                  : -128 dBm
  Channel Dwell Times
    Minimum                                  : unknown
    Average                                  : unknown
    Maximum                                  : unknown
  802.11a 5 GHz Auto-RF Channel List
    Allowed Channel List                     : 36,40,44,48,52,56,60,64,100,104,108,112,116,120,124,128,132,136,140,144,149,153,157,161
    Unused Channel List                      : 165


------------------ show ap dot11 24ghz coverage ------------------


Coverage Hole Detection
  802.11b Coverage Hole Detection Mode             : Enabled
  802.11b Coverage Voice Packet Count              : 100 packet(s)
  802.11b Coverage Voice Packet Percentage         : 50%
  802.11b Coverage Voice RSSI Threshold            : -80 dBm
  802.11b Coverage Data Packet Count               : 50 packet(s)
  802.11b Coverage Data Packet Percentage          : 50%
  802.11b Coverage Data RSSI Threshold             : -80 dBm
  802.11b Global coverage exception level          : 25 %
  802.11b Global client minimum exception level    : 3 clients


------------------ show ap dot11 5ghz coverage ------------------


Coverage Hole Detection
  802.11a Coverage Hole Detection Mode          : Enabled
  802.11a Coverage Voice Packet Count           : 100 packet(s)
  802.11a Coverage Voice Packet Percentage      : 50 %
  802.11a Coverage Voice RSSI Threshold         : -80dBm
  802.11a Coverage Data Packet Count            : 50 packet(s)
  802.11a Coverage Data Packet Percentage       : 50 %
  802.11a Coverage Data RSSI Threshold          : -80dBm
  802.11a Global coverage exception level       : 25 %
  802.11a Global client minimum exception level : 3 clients


------------------ show ap dot11 24ghz group ------------------


Radio RF Grouping

  802.11b Group Mode               : AUTO
  802.11b Group Update Interval    : 600 seconds
  802.11b Group Leader             : ewlc-doc (9.12.32.10)
  802.11b Last Run                 : 553 seconds ago


RF Group Members

Controller name                   Controller IP     
--------------------------------------------------
ewlc-doc                          9.12.32.10        




------------------ show ap dot11 5ghz group ------------------


Radio RF Grouping

  802.11a Group Mode               : AUTO
  802.11a Group Update Interval    : 600 seconds
  802.11a Group Leader             : ewlc-doc (9.12.32.10)
  802.11a Last Run                 : 553 seconds ago


RF Group Members

Controller name                   Controller IP     
--------------------------------------------------
ewlc-doc                          9.12.32.10        




------------------ show ap dot11 24ghz high-density ------------------



------------------ show ap dot11 5ghz high-density ------------------



------------------ show ap dot11 5ghz load-info ------------------



------------------ show ap dot11 24ghz load-info ------------------



------------------ show ap dot11 24ghz profile ------------------



Default 802.11b AP performance profiles
  802.11b Global Interference threshold    : 10 %
  802.11b Global noise threshold           : -70 dBm
  802.11b Global RF utilization threshold  : 80 %
  802.11b Global throughput threshold      : 1000000 bps
  802.11b Global clients threshold         : 12 clients


------------------ show ap dot11 5ghz profile ------------------


Default 802.11a AP performance profiles

  802.11a Global Interference threshold          : 10 %
  802.11a Global noise threshold                 : -70 dBm
  802.11a Global RF utilization threshold        : 80 %
  802.11a Global throughput threshold            : 1000000 bps
  802.11a Global clients threshold               : 12 clients


------------------ show ap dot11 24ghz monitor ------------------


Default 802.11b AP monitoring
  802.11b Monitor Mode                 : Enabled
  802.11b Monitor Channels             : Country channels
  802.11b RRM Neighbor Discover Type   : Transparent
  802.11b AP Coverage Interval         : 180 seconds
  802.11b AP Load Interval             : 60 seconds
  802.11b AP Noise Interval            : 180 seconds
  802.11b AP Signal Strength Interval  : 60 seconds
  802.11b NDP RSSI Normalization       : Enabled


------------------ show ap dot11 5ghz monitor ------------------


Default 802.11a AP monitoring
  802.11a Monitor Mode                 : Enabled
  802.11a Monitor Channels             : Country channels
  802.11a RRM Neighbor Discover Type   : Transparent
  802.11a AP Coverage Interval         : 180 seconds
  802.11a AP Load Interval             : 60 seconds
  802.11a AP Noise Interval            : 180 seconds
  802.11a AP Signal Strength Interval  : 60 seconds
  802.11a NDP RSSI Normalization       : Enabled


------------------ show ap dot11 24ghz network ------------------



802.11b Network                           : Enabled
11gSupport                                : Enabled
11nSupport                                : Enabled
802.11b/g Operational Rates
  802.11b 1M                              : Mandatory
  802.11b 2M                              : Mandatory
  802.11b 5.5M                            : Mandatory
  802.11b 11M                             : Mandatory
  802.11g 6M                              : Supported
  802.11g 9M                              : Supported
  802.11g 12M                             : Supported
  802.11g 18M                             : Supported
  802.11g 24M                             : Supported
  802.11g 36M                             : Supported
  802.11g 48M                             : Supported
  802.11g 54M                             : Supported
802.11n MCS Settings:
  MCS 0 : Supported
  MCS 1 : Supported
  MCS 2 : Supported
  MCS 3 : Supported
  MCS 4 : Supported
  MCS 5 : Supported
  MCS 6 : Supported
  MCS 7 : Supported
  MCS 8 : Supported
  MCS 9 : Supported
  MCS 10 : Supported
  MCS 11 : Supported
  MCS 12 : Supported
  MCS 13 : Supported
  MCS 14 : Supported
  MCS 15 : Supported
  MCS 16 : Supported
  MCS 17 : Supported
  MCS 18 : Supported
  MCS 19 : Supported
  MCS 20 : Supported
  MCS 21 : Supported
  MCS 22 : Supported
  MCS 23 : Supported
  MCS 24 : Supported
  MCS 25 : Supported
  MCS 26 : Supported
  MCS 27 : Supported
  MCS 28 : Supported
  MCS 29 : Supported
  MCS 30 : Supported
  MCS 31 : Supported
802.11n Status:
  A-MPDU Tx:
    Priority 0                            : Enabled
    Priority 1                            : Disabled
    Priority 2                            : Disabled
    Priority 3                            : Disabled
    Priority 4                            : Enabled
    Priority 5                            : Enabled
    Priority 6                            : Disabled
    Priority 7                            : Disabled
    Aggregation scheduler                 : Enabled
    Realtime timeout                      : 10
  A-MSDU Tx:
    Priority 0                            : Enable
    Priority 1                            : Enable
    Priority 2                            : Enable
    Priority 3                            : Enable
    Priority 4                            : Enable
    Priority 5                            : Enable
    Priority 6                            : Disable
    Priority 7                            : Disable
  Guard Interval                          : Any
  Rifs Rx                                 : Enabled
Beacon Interval                           : 100
CF Pollable mandatory                     : Disabled
CF Poll Request Mandatory                 : Disabled
CFP Period                                : 4
CFP Maximum Duration                      : 60
Default Channel                           : 1
Default Tx Power Level                    : 1
DTPC Status                               : Enabled
Call Admission Limit                      : 
G711 CU Quantum                           : 
ED Threshold                              : -50
Fragmentation Threshold                   : 2346
RSSI Low Check                           : Disabled
RSSI Threshold                            : -127 dbm
PBCC Mandatory                            : unknown
Pico-Cell-V2 Status                       : unknown
RTS Threshold                             : 2347
Short Preamble Mandatory                  : Enabled
Short Retry Limit                         : 7
Legacy Tx Beamforming setting             : Disabled
Traffic Stream Metrics Status             : Disabled
Expedited BW Request Status               : Disabled
EDCA profile type check                   : default-wmm
Call Admision Control (CAC) configuration
Voice AC
  Voice AC - Admission control (ACM)      : Disabled
  Voice Stream-Size                       : 84000
  Voice Max-Streams                       : 2
  Voice Max RF Bandwidth                  : 75
  Voice Reserved Roaming Bandwidth        : 6
  Voice Load-Based CAC mode               : Enabled
  Voice tspec inactivity timeout          : Enabled
CAC SIP-Voice configuration
  SIP based CAC                           : Disabled
  SIP call bandwidth                      : 64
  SIP call bandwith sample-size           : 20
Maximum Number of Clients per AP Radio    : 200


------------------ show ap dot11 5ghz network ------------------



802.11a Network                           : Enabled
11nSupport                                : Enabled
  802.11a Low Band                        : Enabled
  802.11a Mid Band                        : Enabled
  802.11a High Band                       : Enabled
802.11a Operational Rates
  802.11a 6M                              : Mandatory
  802.11a 9M                              : Supported
  802.11a 12M                             : Mandatory
  802.11a 18M                             : Supported
  802.11a 24M                             : Mandatory
  802.11a 36M                             : Supported
  802.11a 48M                             : Supported
  802.11a 54M                             : Supported
802.11n MCS Settings:
  MCS 0 : Supported
  MCS 1 : Supported
  MCS 2 : Supported
  MCS 3 : Supported
  MCS 4 : Supported
  MCS 5 : Supported
  MCS 6 : Supported
  MCS 7 : Supported
  MCS 8 : Supported
  MCS 9 : Supported
  MCS 10 : Supported
  MCS 11 : Supported
  MCS 12 : Supported
  MCS 13 : Supported
  MCS 14 : Supported
  MCS 15 : Supported
  MCS 16 : Supported
  MCS 17 : Supported
  MCS 18 : Supported
  MCS 19 : Supported
  MCS 20 : Supported
  MCS 21 : Supported
  MCS 22 : Supported
  MCS 23 : Supported
  MCS 24 : Supported
  MCS 25 : Supported
  MCS 26 : Supported
  MCS 27 : Supported
  MCS 28 : Supported
  MCS 29 : Supported
  MCS 30 : Supported
  MCS 31 : Supported
802.11n Status:
  A-MPDU Tx:
    Priority 0                            : Enabled
    Priority 1                            : Disabled
    Priority 2                            : Disabled
    Priority 3                            : Disabled
    Priority 4                            : Enabled
    Priority 5                            : Enabled
    Priority 6                            : Disabled
    Priority 7                            : Disabled
    Aggregation scheduler                 : Enabled
    Realtime timeout                      : 10
  A-MSDU Tx:
    Priority 0                            : Enable
    Priority 1                            : Enable
    Priority 2                            : Enable
    Priority 3                            : Enable
    Priority 4                            : Enable
    Priority 5                            : Enable
    Priority 6                            : Disable
    Priority 7                            : Disable
  Guard Interval                          : Any
  Rifs Rx                                 : Enabled
802.11ac                                  : Enabled
  Frame burst                             : Automatic
802.11ac MCS Settings:
Beacon Interval                           : 100
CF Pollable mandatory                     : Disabled
CF Poll Request Mandatory                 : Disabled
CFP Period                                : 4
CFP Maximum Duration                      : 60
Default Channel                           : 36
Default Tx Power Level                    : 1
DTPC Status                               : Enabled
Fragmentation Threshold                   : 2346
RSSI Low Check	                          : Disabled
RSSI Threshold                            : -127 dbm
Pico-Cell-V2 Status                       : unknown
TI Threshold                              : 
Legacy Tx Beamforming setting             : Disabled
Traffic Stream Metrics Status             : Disabled
Expedited BW Request Status               : Disabled
EDCA profile type check                   : default-wmm
Call Admision Control (CAC) configuration
Voice AC
  Voice AC - Admission control (ACM)      : Disabled
  Voice Stream-Size                       : 84000
  Voice Max-Streams                       : 2
  Voice Max RF Bandwidth                  : 75
  Voice Reserved Roaming Bandwidth        : 6
  Voice Load-Based CAC mode               : Enabled
  Voice tspec inactivity timeout          : Enabled
CAC SIP-Voice configuration
  SIP based CAC                           : Disabled
  SIP call bandwidth                      : 64
  SIP call bandwith sample-size           : 20
Maximum Number of Clients per AP Radio    : 200


------------------ show ap dot11 24ghz txpower ------------------


Automatic Transmit Power Assignment

Transmit Power Assignment Mode          : AUTO
Transmit Power Update Interval          : 600 seconds 
Transmit Power Threshold                : -70 dBm
Transmit Power Neighbor Count           : 3 APs
Min Transmit Power                      : -10 dBm
Max Transmit Power                      : 30 dBm
Update Contribution
    Noise                               : Enable
    Interference                        : Enable
    Load                                : Disable
    Device Aware                        : Disable
Transmit Power Assignment Leader        : ewlc-doc (9.12.32.10)
Last Run                                : 558 seconds ago


------------------ show ap dot11 5ghz txpower ------------------


Automatic Transmit Power Assignment

Transmit Power Assignment Mode          : AUTO
Transmit Power Update Interval          : 600 seconds 
Transmit Power Threshold                : -70 dBm
Transmit Power Neighbor Count           : 3 APs
Min Transmit Power                      : -10 dBm
Max Transmit Power                      : 30 dBm
Update Contribution
    Noise                               : Enable
    Interference                        : Enable
    Load                                : Disable
    Device Aware                        : Disable
Transmit Power Assignment Leader        : ewlc-doc (9.12.32.10)
Last Run                                : 558 seconds ago


------------------ show ap auto-rf dot11 5ghz ------------------



------------------ show ap auto-rf dot11 24ghz ------------------



------------------ show ap config general ------------------




------------------ show ap dot11 5ghz optimized-roaming ------------------

802.11a OptimizedRoaming

  Mode                                  : Disabled
  Reporting Interval                    : 90 seconds
  Rate Threshold                        : Disabled 
  Hysteresis                            : 6 db


------------------ show ap rf-profile summary ------------------



Number of RF-profiles: 6

RF Profile Name                  Band     Description                          State 
------------------------------------------------------------------------------------
Low_Client_Density_rf_5gh        5 GHz    pre configured Low Client Density rf Up    
High_Client_Density_rf_5gh       5 GHz    pre configured High Client Density r Up    
Low_Client_Density_rf_24gh       2.4 GHz  pre configured Low Client Density rf Up    
High_Client_Density_rf_24gh      2.4 GHz  pre configured High Client Density r Up    
Typical_Client_Density_rf_5gh    5 GHz    pre configured Typical Density rfpro Up    
Typical_Client_Density_rf_24gh   2.4 GHz  pre configured Typical Client Densit Up    


------------------ show ap fra ------------------

FRA State                                             : Disabled
FRA Sensitivity                                       : medium (95%)
FRA Interval                                          : 1 Hour(s)
  Last Run                                            : 2299 seconds ago
  Last Run time                                       : 0 seconds

AP Name              MAC Address       Slot ID  Current-Band      COF %      Suggested Mode
-------------------------------------------------------------------------------------------

COF : Coverage Overlap Factor


------------------ show wireless band-select ------------------


Band Select Probe Response   : per WLAN enabling
Cycle Count                  : 2
Cycle Threshold (millisec)   : 200
Age Out Suppression (sec)    : 20
Age Out Dual Band (sec)      : 60
Client RSSI (dBm)            : -80
Client Mid RSSI (dBm)        : -80


------------------ show wireless  country  configure ------------------



Configured Country..........................   US - United States                       
Configured Country Codes
        US  - United States                  802.11a Indoor/ 802.11b Indoor/ 802.11g Indoor 


------------------ show wireless tag rf summary ------------------



Number of RF Tags: 1

RF tag name                       Description                             
------------------------------------------------------------------------
default-rf-tag                    default RF tag                          


------------------ show ap tag summary ------------------


Number of APs: 0



------------------ show ap status ------------------



------------------ show ap uptime ------------------


Number of APs: 0

show tunnel eogre global-configuration

To display the Ethernet over GRE (EoGRE) global configuration, use the show tunnel eogre global-configuration command.

show tunnel eogre global-configuration

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to display the EoGRE global configuration:

Device# show tunnel eogre global-configuration 

Heartbeat interval       : 60
Max Heartbeat skip count : 3
Source Interface         : (none)

show tunnel eogre domain detailed

To display the detailed information of the Ethernet over GRE (EoGRE) tunnel domain, use the show tunnel eogre domain detailed command.

show tunnel eogre domain detailed domain-name

Syntax Description


`domain-name`	EoGRE domain name.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to display the detailed information of the EoGRE tunnel domain:

Device# show tunnel eogre domain detailed eogre_domain

Domain Name    : eogre_domain
 Primary GW    : Tunnel1
 Secondary GW  : Tunnel2
 Active GW     : Tunnel1
 Redundancy    : Non-Revertive

show tunnel eogre domain summary

To display the summary information of the Ethernet over GRE (EoGRE) tunnel domain, use the show tunnel eogre domain summary command.

show tunnel eogre domain summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to display the summary information of the EoGRE tunnel domain:

Device# show tunnel eogre domain summary 

Domain Name         Primary GW   Secondary GW      Active GW      Redundancy
-------------------------------------------------------------------------------
domain1             Tunnel1      Tunnel2           Tunnel1        Non-Revertive
eogre_domain        Tunnel1      Tunnel2           Tunnel1        Non-Revertive

show tunnel eogre gateway summary

To display the summary information of the Ethernet over GRE (EoGRE) tunnel gateway, use the show tunnel eogre gateway summary command.

show tunnel eogre gateway summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to display the summary information of the EoGRE tunnel gateway:

Device# show tunnel eogre gateway summary

Name               Type  Address                                  AdminState  State  Clients
---------------------------------------------------------------------------------------------
Tunnel1            IPv4  9.51.1.11                                Up          Up     0       
Tunnel2            IPv4  9.51.1.12                                Up          Down   0       
Tunnel10           IPv6  fd09:9:8:21::90                          Down        Down   0       
Tunnel11           IPv4  9.51.1.11                                Up          Up     0       
Tunnel12           IPv6  fd09:9:8:21::90                          Up          Down   0       
Tunnel100          IPv4  9.51.1.100                               Up          Down   0

show tunnel eogre gateway detailed

To display the detailed information of the Ethernet over GRE (EoGRE) tunnel domain, use the show tunnel eogre gateway detailed command.

show tunnel eogre gateway detailed gateway-name

Syntax Description


`gateway-name`	EoGRE gateway name.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to display the detailed information of the EoGRE tunnel gateway:

Device# show tunnel eogre domain detailed Tunnel1

Gateway : Tunnel1
 Mode   : IPv4
 IP     : 9.51.1.11
 Source : Vlan51 / 9.51.1.1
 State  : Up
 SLA ID : 56
 MTU    : 1480
 Up Time: 4 minutes 45 seconds 

 Clients
  Total Number of Wireless Clients      : 0
 Traffic
  Total Number of Received Packets      : 0
  Total Number of Received Bytes        : 0
  Total Number of Transmitted Packets   : 0
  Total Number of Transmitted Bytes     : 0
 Keepalives
  Total Number of Lost Keepalives       : 0
  Total Number of Received Keepalives   : 5
  Total Number of Transmitted Keepalives: 5
  Windows                               : 1
  Transmitted Keepalives in last window : 2
  Received Keepalives in last window    : 2

show tunnel eogre manager stats global

To display the global tunnel manager statistics, use the show tunnel eogre manager stats global command.

show tunnel eogre manager stats global

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to display the global tunnel manager statistics:

Device# show tunnel eogre manager stats global 

Tunnel Global Statistics
Last Updated                     : 02/18/2019 23:50:35
EoGRE Objects
  Gateways                       : 6
  Domains                        : 2

EoGRE Flex Objects
  AP Gateways                    : 2
  AP Domains                     : 1
  AP Gateways HA inconsistencies : 0
  AP Domains HA inconsistencies  : 0

Config events
  IOS Tunnel updates             : 806
  IOS Domain updates             : 88
  Global updates                 : 48
  Tunnel Profile updates         : 120
  Tunnel Rule updates            : 16
  AAA proxy key updates          : 0

AP events
  Flex AP Join                   : 1
  Flex AP Leave                  : 0
  Local AP Join                  : 0
  Local AP leave                 : 0
  Tunnel status (rx)             : 4
  Domain status (rx)             : 1
  IAPP stats msg (rx)            : 3
  Client count (rx)              : 6
  VAP Payload msg (tx)           : 4
  Domain config (tx)             : 1
  Global config (tx)             : 1
  Client delete (tx)             : 1
  Client delete per domain (tx)  : 3
  DHCP option 82 (tx)            : 4

Client events
  Add-mobile                     : 2
  Run-State                      : 3
  Delete                         : 1
  Cleanup                        : 0
  Join                           : 2
  Plumb                          : 0
  Join Errors                    : 0
  HandOff                        : 0
  MsPayload                      : 2
  FT Recover                     : 0
  Zombie GW counter increase     : 0
  Zombie GW counter decrease     : 0
  Tunnel Profile reset           : 88
  Client deauth                  : 0
  HA reconciliation              : 0

Client Join Events
  Generic Error                  : 0
  MSPayload Fail                 : 0
  Invalid VLAN                   : 0
  Invalid Domain                 : 0
  No GWs in Domain               : 0
  Domain Shut                    : 0
  Invalid GWs                    : 0
  GWs Down                       : 0
  Rule Match Error               : 0
  AAA-override                   : 0
  Flex No Active GW              : 0
  Open Auth join attempt         : 2
  Dot1x join attempt             : 2
  Mobility join attempt          : 0
  Tunnel Profile not valid       : 2
  Tunnel Profile valid           : 2
  No rule match                  : 0
  Rule match                     : 2
  AAA proxy                      : 0
  AAA proxy accounting           : 0
  AAA eogre attributes           : 0
  Has aaa override               : 0
  Error in handoff payload       : 0
  Handoff AAA override           : 0
  Handoff no AAA override        : 0
  Handoff payload received       : 0
  Handoff payload sent           : 0

SNMP Traps
  Client                         : 0
  Tunnel                         : 2
  Domain                         : 0

IPC
  IOSd TX messages               : 0

Zombie Client
  Entries                        : 0

show tunnel eogre manager stats instance

To display the tunnel manager statistics for a specific WNCd instance, use the show tunnel eogre manager stats instance command.

show tunnel eogre manager stats instance instance-number

Syntax Description


`instance-number`	WNCd instance number.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to display the tunnel manager statistics for a specific WNCd instance:

Device# show tunnel eogre manager stats instance 0

Tunnel Manager statistics for process instance : 0
Last Updated                     : 02/18/2019 23:50:35
EoGRE Objects
  Gateways                       : 6
  Domains                        : 2

EoGRE Flex Objects
  AP Gateways                    : 2
  AP Domains                     : 1
  AP Gateways HA inconsistencies : 0
  AP Domains HA inconsistencies  : 0

Config events
  IOS Tunnel updates             : 102
  IOS Domain updates             : 11
  Global updates                 : 6
  Tunnel Profile updates         : 15
  Tunnel Rule updates            : 2
  AAA proxy key updates          : 0

AP events
  Flex AP Join                   : 1
  Flex AP Leave                  : 0
  Local AP Join                  : 0
  Local AP leave                 : 0
  Tunnel status (rx)             : 4
  Domain status (rx)             : 1
  IAPP stats msg (rx)            : 3
  Client count (rx)              : 6
  VAP Payload msg (tx)           : 4
  Domain config (tx)             : 1
  Global config (tx)             : 1
  Client delete (tx)             : 1
  Client delete per domain (tx)  : 3
  DHCP option 82 (tx)            : 4

Client events
  Add-mobile                     : 2
  Run-State                      : 3
  Delete                         : 1
  Cleanup                        : 0
  Join                           : 2
  Plumb                          : 0
  Join Errors                    : 0
  HandOff                        : 0
  MsPayload                      : 2
  FT Recover                     : 0
  Zombie GW counter increase     : 0
  Zombie GW counter decrease     : 0
  Tunnel Profile reset           : 11
  Client deauth                  : 0
  HA reconciliation              : 0

Client Join Events
  Generic Error                  : 0
  MSPayload Fail                 : 0
  Invalid VLAN                   : 0
  Invalid Domain                 : 0
  No GWs in Domain               : 0
  Domain Shut                    : 0
  Invalid GWs                    : 0
  GWs Down                       : 0
  Rule Match Error               : 0
  AAA-override                   : 0
  Flex No Active GW              : 0
  Open Auth join attempt         : 2
  Dot1x join attempt             : 2
  Mobility join attempt          : 0
  Tunnel Profile not valid       : 2
  Tunnel Profile valid           : 2
  No rule match                  : 0
  Rule match                     : 2
  AAA proxy                      : 0
  AAA proxy accounting           : 0
  AAA eogre attributes           : 0
  Has aaa override               : 0
  Error in handoff payload       : 0
  Handoff AAA override           : 0
  Handoff no AAA override        : 0
  Handoff payload received       : 0
  Handoff payload sent           : 0

SNMP Traps
  Client                         : 0
  Tunnel                         : 2
  Domain                         : 0

IPC
  IOSd TX messages               : 0

Zombie Client
  Entries                        : 0

show umbrella config

To view the Umbrella configuration details, use the show umbrella config command.

show umbrella config

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the Umbrella configuration details:

Device# show umbrella config
Umbrella Configuration
========================
   Token: 57CC80106C087FB1B2A7BAB4F2F4373C00247166
   OrganizationID: 1892929
   Local Domain Regex parameter-map name: dns_wl
   DNSCrypt: Enabled
   Public-key: B735:1140:206F:225D:3E2B:D822:D7FD:691E:A1C3:3CC8:D666:8D0C:BE04:BFAB:CA43:FB79
   UDP Timeout: 2 seconds
   Resolver address:
       1. 208.67.220.220
       2. 208.67.222.222
       3. 2620:119:53::53
       4. 2620:119:35::35

show umbrella deviceid

To view the device registration details, use the show umbrella deviceid command.

show umbrella deviceid

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the device registration details:

Device# show umbrella deviceid
Device registration details
Profile Name             Tag              Status            Device-id
GigabitEthernet0/0/0    guest          200 SUCCESS     010a470b042a072d

show umbrella deviceid detailed

To view the detailed description for the Umbrella device ID, use the show umbrella deviceid detailed command.

show umbrella deviceid detailed

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the detailed description for the Umbrella device ID:

Device# show umbrella deviceid detailed
Device registration details
 1.GigabitEthernet0/0/0
      Tag               : guest
      Device-id         : 010a470b042a072d
      Description       : Device Id recieved successfully

show umbrella dnscrypt

To view the Umbrella DNScrypt details, use the show umbrella dnscrypt command.

show umbrella dnscrypt

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the Umbrella DNScrypt details:

Device# show umbrella dnscrypt
DNSCrypt: Enabled
   Public-key: B735:1140:206F:225D:3E2B:D822:D7FD:691E:A1C3:3CC8:D666:8D0C:BE04:BFAB:CA43:FB79
   Certificate Update Status:
        Last Successfull Attempt: 17:45:57 IST Nov 9 2017
   Certificate Details:
       Certificate Magic     : DNSC
       Major Version         : 0x0001
       Minor Version         : 0x0000
       Query Magic           : 0x713156774457306E
       Serial Number         : 1490391488
       Start  Time           : 1490391488 (03:08:08 IST Mar 25 2017)
       End Time              : 1521927488 (03:08:08 IST Mar 25 2018)
       Server Public Key     : E7F8:4477:BF89:1434:1ECE:23F0:D6A6:6EB9:4F45:3167:D71F:80BB:4E80:A04F:F180:F778
       Client Secret Key Hash: F1A5:1993:F729:5416:53B7:94E3:6509:8182:A708:0561:8050:6CE0:DFA1:5C94:6EE4:0010
       Client Public key     : BC6D:3758:48B6:120B:D2F5:F25B:2979:564D:F52C:5EFA:B0BD:76FE:3CD6:828B:44D2:FF3A
       NM key Hash           : 1FF7:2E1E:EFB9:7987:9CB4:3EF8:A25B:4DAD:10FC:7DF7:6985:6E8E:6E4D:D56A:1C70:B9EB

show vlan

To display the parameters for all configured VLANs or one VLAN (if the VLAN ID or name is specified) on the switch, use the show vlan command in user EXEC mode.

Syntax Description

brief

(Optional) Displays one line for each VLAN with the VLAN name, status, and its ports.

group

(Optional) Displays information about VLAN groups.

id vlan-id

(Optional) Displays information about a single VLAN identified by the VLAN ID number. For vlan-id , the range is 1 to 4094.

mtu

(Optional) Displays a list of VLANs and the minimum and maximum transmission unit (MTU) sizes configured on ports in the VLAN.

Note

Traceback occurs in the VLAN CLI parser when Controller-PI does VLAN lookup for each interface.

name vlan-name

(Optional) Displays information about a single VLAN identified by the VLAN name. The VLAN name is an ASCII string from 1 to 32 characters.

remote-span

(Optional) Displays information about Remote SPAN (RSPAN) VLANs.

summary

(Optional) Displays VLAN summary information.

Note

The ifindex keyword is not supported, even though it is visible in the command-line help string.

Command Default

None

Command Modes

User EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

In the show vlan mtu command output, the MTU_Mismatch column shows whether all the ports in the VLAN have the same MTU. When yes appears in the column, it means that the VLAN has ports with different MTUs, and packets that are switched from a port with a larger MTU to a port with a smaller MTU might be dropped. If the VLAN does not have an SVI, the hyphen (-) symbol appears in the SVI_MTU column. If the MTU-Mismatch column displays yes, the names of the ports with the MinMTU and the MaxMTU appear.

Examples

This is an example of output from the show vlan command. See the table that follows for descriptions of the fields in the display.

Device> show vlan
VLAN Name                             Status    Ports
---- -------------------------------- --------- -------------------------------
1    default                          active    Gi1/0/2, Gi1/0/3, Gi1/0/4
                                                Gi1/0/5, Gi1/0/6, Gi1/0/7
                                                Gi1/0/8, Gi1/0/9, Gi1/0/10
                                                Gi1/0/11, Gi1/0/12, Gi1/0/13
                                                Gi1/0/14, Gi1/0/15, Gi1/0/16
                                                Gi1/0/17, Gi1/0/18, Gi1/0/19
                                                Gi1/0/20, Gi1/0/21, Gi1/0/22
                                                Gi1/0/23, Gi1/0/24, Gi1/0/25
                                                Gi1/0/26, Gi1/0/27, Gi1/0/28
                                                Gi1/0/29, Gi1/0/30, Gi1/0/31
                                                Gi1/0/32, Gi1/0/33, Gi1/0/34
                                                Gi1/0/35, Gi1/0/36, Gi1/0/37
                                                Gi1/0/38, Gi1/0/39, Gi1/0/40
                                                Gi1/0/41, Gi1/0/42, Gi1/0/43
                                                Gi1/0/44, Gi1/0/45, Gi1/0/46
                                                Gi1/0/47, Gi1/0/48
2    VLAN0002                         active
40   vlan-40                          active
300  VLAN0300                         active
1002 fddi-default                     act/unsup
1003 token-ring-default               act/unsup
1004 fddinet-default                  act/unsup
1005 trnet-default                    act/unsup

VLAN Type  SAID       MTU   Parent RingNo BridgeNo Stp  BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1    enet  100001     1500  -      -      -        -    -        0      0
2    enet  100002     1500  -      -      -        -    -        0      0
40   enet  100040     1500  -      -      -        -    -        0      0
300  enet  100300     1500  -      -      -        -    -        0      0
1002 fddi  101002     1500  -      -      -        -    -        0      0
1003 tr    101003     1500  -      -      -        -    -        0      0
1004 fdnet 101004     1500  -      -      -        ieee -        0      0
1005 trnet 101005     1500  -      -      -        ibm  -        0      0
2000 enet  102000     1500  -      -      -        -    -        0      0
3000 enet  103000     1500  -      -      -        -    -        0      0

Remote SPAN VLANs
------------------------------------------------------------------------------
2000,3000

Primary Secondary Type              Ports
------- --------- ----------------- ------------------------------------------

Table 15. show vlan Command Output Fields
Field	Description
VLAN	VLAN number.
Name	Name, if configured, of the VLAN.
Status	Status of the VLAN (active or suspend).
Ports	Ports that belong to the VLAN.
Type	Media type of the VLAN.
SAID	Security association ID value for the VLAN.
MTU	Maximum transmission unit size for the VLAN.
Parent	Parent VLAN, if one exists.
RingNo	Ring number for the VLAN, if applicable.
BrdgNo	Bridge number for the VLAN, if applicable.
Stp	Spanning Tree Protocol type used on the VLAN.
BrdgMode	Bridging mode for this VLAN—possible values are source-route bridging (SRB) and source-route transparent (SRT); the default is SRB.
Trans1	Translation bridge 1.
Trans2	Translation bridge 2.
Remote SPAN VLANs	Identifies any RSPAN VLANs that have been configured.

This is an example of output from the show vlan summary command:

Device> show vlan summary
Number of existing VLANs               : 45
 Number of existing VTP VLANs          : 45
 Number of existing extended VLANS     : 0

This is an example of output from the show vlan id command:

Device# show vlan id 2
VLAN Name                             Status    Ports
---- -------------------------------- --------- -------------------------------
2    VLAN0200                         active    Gi1/0/7, Gi1/0/8
2    VLAN0200                         active    Gi2/0/1, Gi2/0/2

VLAN Type  SAID       MTU   Parent RingNo BridgeNo Stp  BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
2    enet  100002     1500  -      -      -        -    -        0      0

Remote SPAN VLANs
------------------------------------------------------------------------------
Disabled

show vlan access-map

To display information about a particular VLAN access map or for all VLAN access maps, use the show vlan access-map command in privileged EXEC mode.

show vlan access-map [map-name]

Syntax Description


`map-name`	(Optional) Name of a specific VLAN access map.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This is an example of output from the show vlan access-map command:

Device# show vlan access-map
Vlan access-map "vmap4"  10
  Match clauses:
    ip  address: al2
  Action:
    forward
Vlan access-map "vmap4"  20
  Match clauses:
    ip  address: al2
  Action:
    forward

show vlan filter

To display information about all VLAN filters or about a particular VLAN or VLAN access map, use the show vlan filter command in privileged EXEC mode.

show vlan filter {access-map name | vlan vlan-id}

Syntax Description


access-map `name`	(Optional) Displays filtering information for the specified VLAN access map.
vlan `vlan-id`	(Optional) Displays filtering information for the specified VLAN. The range is 1 to 4094.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This is an example of output from the show vlan filter command:

Device# show vlan filter
VLAN Map map_1 is filtering VLANs:
  20-22

show vlan group

To display the VLANs that are mapped to VLAN groups, use the show vlan group command in privileged EXEC mode.

show vlan group [group-name vlan-group-name [user_count]]

Syntax Description


group-name `vlan-group-name`	(Optional) Displays the VLANs mapped to the specified VLAN group.
user_count	(Optional) Displays the number of users in each VLAN mapped to a specified VLAN group.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

The show vlan group command displays the existing VLAN groups and lists the VLANs and VLAN ranges that are members of each VLAN group. If you enter the group-name keyword, only the members of the specified VLAN group are displayed.

Examples

This example shows how to display the members of a specified VLAN group:

show vrrp events

To display Virtual Router Redundancy Protocol (VRRP) events, use the show vrrp events command.

show vrrp events

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC(#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.2.1	This command was introduced.

Usage Guidelines

VRRP commands are displayed only in ME mode; it is hidden in other AP modes.

Examples

This example shows how to view the VRRP events:

Device# show vrrp events 

VRRP Events: 
Dec 7 2019 01:17:23: Current state : backup, My Eth : A4:53:0E:7B:CD:84, event : VRRP Element is started. Start
sending KeepAlive Pkts to check if Ether link is up 
Dec 7 2019 01:17:28: Current state : backup, My Eth : A4:53:0E:7B:CD:84, event : Detected Link is up. Now
waiting for 30 seconds to participate in VRRP election 
Dec 7 2019 01:18:01: Current state : master, My Eth : A4:53:0E:7B:CD:84, event : Current master
(00:00:00:00:00:00) went down (lost 3 advertisement). Moving to master state. And starting election 
Dec 7 2019 01:18:05: Current state : master, My Eth : A4:53:0E:7B:CD:84, event : Launched controller process on
this ap

show vrrp statistics

To display the Virtual Router Redundancy Protocol (VRRP) statistics, use the show vrrp statistics command in privileged EXEC mode.

show vrrp statistics

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.2.1	This command was introduced.

Usage Guidelines

VRRP commands are displayed only in ME mode; it is hidden in other AP modes.

Examples

This example shows how to view the VRRP statistics:

Device# show vrrp statistics
 
VRRP Statistics : 
VRRP Statistics : 
Invalid VRRP packets recvd:0
Number of incoming VRRP Pkts:0
Number of VRRP Pkts transmitted:148054
Number of VRRP Pkts recvd from Master:0
Number of VRRP Pkts recvd in Init state:0
Number of VRRP Pkts with STOP Priority:0

show vrrp status

To display the Virtual Router Redundancy Protocol (VRRP) status, use the show vrrp status command.

show vrrp status

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC(#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.2.1	This command was introduced.

Usage Guidelines

VRRP commands are displayed only in ME mode; it is hidden in other AP modes.

Examples

This example shows how to view the VRRP status:

Device# show vrrp status

 VRRP Status : MASTER
Preferred AP : 00:00:00:00:00:00
My Eth : A4:53:0E:7B:CD:84
AP Type : VANCOUVER
VRRP Instance : vrid state priority vrrp_ip_vlans adver_ival   
1 master 1 0.0.0.0:0 3.000000

show wireless stats ap history

To verify historical statistics of an AP, use the show wireless stats ap history command.

show wireless stats ap history

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC#

Command History


Release	Modification
Cisco IOS XE Cupertino 17.7.1	This command was introduced.

Examples

This example shows how to verify the statistics of the access point hisory:

Device# show wireless stats ap history
AP Name             Radio MAC       Event      Time               Recent      Disconnect Reason          Disconnect 
                                                                  Disconnect  Reason                     Count
                                                                  Time
------------------------------------------------------------------------------------------------------------------------
APA023.9FD8.EA22   40ce.24bf.8ca0  Joined     06/26/21 10:11:52  NA           NA                         NA
APA023.9FD8.EA22   40ce.24bf.8ca0  Disjoined  06/26/21 10:05:18  NA           Heart beat timer expiry    1
APA023.9FD8.EA22   40ce.24bf.8ca0  Joined     06/22/21 17:00:39  NA           NA                         NA
APA023.9FD8.EA22   40ce.24bf.8ca0  Disjoined  06/22/21 16:54:54  NA           Heart beat timer expiry    1
APA023.9FD8.EA22   40ce.24bf.8ca0  Joined     06/21/21 23:01:17  NA           NA                         NA
APA023.9FD8.EA22   40ce.24bf.8ca0  Disjoined  06/21/21 22:56:21  NA           Image Download Success     1

show wireless stats ap join summary

To verify the statistics of the access point join summary, use the show wireless stats ap join summary command.

show wireless stats ap join summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC(#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.7.1	This command was introduced.

Examples

This example shows how to verify the statistics of the access point join summary:


Device# show wireless stats ap join summary
Number of APs: 001

Base MAC        Ethernet MAC    AP Name           IP Address  Status  Last           Last 
                                                                      Failure Phase  Disconnect Reason                                                 
--------------------------------------------------------------------------------------------------------
002a.1075.47c0  002a.104d.c9fc  AP002a.104d.c9fc  8.9.10.222  Joined   Run            High CPU usage
003a.1475.57c0  002a.104d.c9fc  AP003a.144d.59fc  7.8.09.111  Joined   Run            High Memory usage

show wireless stats ap join summary sort

To view the sorted wireless statistics access point (AP) join summary, use the show wireless stats ap join summary sort command.

show wireless stats ap join summary sort

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.7.1	This command was introduced.

Usage Guidelines

Wireless AP statistics can be sorted in ascending or descending order by AP name.

Ascending: Displays the ten APs from the bottom.
Descending: Displays the APs from the top.
Name: Displays the APs list sorted by name.

Examples

This example shows how to view the sorted wireless statistics AP join summary:

Device# show wireless stats ap join summary sort
Number of APs: 8

Base MAC        Ethernet MAC      AP Name                           IP Address   Status  Last Failure Phase Last Disconnect Reason
-------------------------------------------------------------------------------------------------------------------------------------
7872.5dee.4960  7872.5ded.cb74   4800-abcdefghijklmnopqrstuvwxyz1   1.11.22.11  Joined  Image-Download     Image Download Success               
10f9.2077.6140  10f9.2076.2c58   9105-abcdefghijklmnopqrstuvwxyz1   1.11.22.11  Joined  Image-Download     Image Download Success               
00ee.ab18.bf00  7069.5a74.9670   9115-abcdefghijklmnopqrstuvwxyz1   1.11.22.11  Joined  Image-Download     Image Download Success               
1416.9d82.ef40  2c57.4152.5e60   9130-abcdefghijklmnopqrstuvwxyz1   1.11.22.11  Joined  Image-Download     Image Download Success               
00d7.8f4e.7040  002a.1087.d68a   AP2800                             1.11.22.11  Joined  Config             DTLS close alert from peer           
687d.b45e.3ed0  687d.b45c.0554   AP687D.B45C.0554                   1.11.22.11  Joined  Image-Download     Image Download Success               
687d.b45e.4c50  687d.b45c.0674   AP687D.B45C.0674                   1.11.22.11  Joined  Config             DTLS close alert from peer           
687d.b45e.53d0  687d.b45c.0714   AP687D.B45C.0714                   1.11.22.11  Joined  Config             DTLS close alert from peer

show wireless stat redundancy statistics client-recovery mobilityd

To view the statistics of Mobilityd configuration database, use the show wireless stat redundancy statistics client-recovery mobilityd command.

show wireless stat redundancy statistics client-recovery mobilityd

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.7.1	This command was introduced.

Examples

The following example shows how to view the statistics of Mobilityd configuration database:

Device# show wireless stat redundancy statistics client-recovery mobilityd

Mobility Client Deletion Reason Statistics
-------------------------------------------
Mobility Incomplete State         : 0
Inconsistency in WNCD & Mobility  : 0
Partial Delete                    : 0
General statistics
--------------------

show wireless stat redundancy statistics client-recovery sisf

To view the statistics for Switch Integrated Security Features (SISF) configuration database, use the show wireless stat redundancy statistics client-recovery sisf command.

show wireless stat redundancy statistics client-recovery sisf

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.7.1	This command was introduced.

Examples

The following example shows how to view the statistics for SISF configuration database:

Device# show wireless stat redundancy statistics client-recovery sisf
Client SSO statistics for SISF
--------------------------------
Number of recreate attempted post switchover    : 0
Number of recreate succeeded post switchover    : 0
Number of recreate failed because of no mac     : 0
Number of recreate failed because of no ip      : 0
Number of ipv4 entry recreate success           : 0
Number of ipv4 entry recreate failed            : 0
Number of ipv6 entry recreate success           : 0
Number of ipv6 entry recreate failed            : 0
Number of partial delete received               : 0
Number of client purge attempted                : 0
Number of heap and db entry purge success       : 0
Number of purge success for db entry only       : 0
Number of client purge failed                   : 0
Number of garp sent                             : 0
Number of garp failed                           : 0
Number of IP table create callbacks on standby  : 0
Number of IP table modify callbacks on standby  : 0
Number of IP table delete callbacks on standby  : 0
Number of MAC table create callbacks on standby : 0
Number of MAC table modify callbacks on standby : 0
Number of MAC table delete callbacks on standby : 0

show wireless stat redundancy client-recovery wncd

To view the redundancy configuration statistics for all the Wireless Network Control Daemon (WNCd) instances, use the show wireless stat redundancy client-recovery wncd command.

show wireless stat redundancy client-recovery wncd { instance-id | all }

Syntax Description


`instance-id`	Instance ID. Valid values range from 0 to 7.
all	Specifies the statistics for all WNCd instances.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.7.1	This command was introduced.

Examples

The following example shows how to view the redundancy configuration statistics for all the WNCd instances:

Device# show wireless stat redundancy statistics client-recovery wncd all

Client SSO statistics
----------------------
No. of Clients                             : 0
No. of Clients recovered successfully      : 0
No. of Clients failed to recover           : 0
No. of Reconcile messages received from AP : 0
WNCD instance  : 0
Reconcile messages received from AP                     : 0
Reconcile clients received from AP                      : 0
Recreate attempted post switchover                      : 0
Recreate attempted by SANET                             : 0
Recreate attempted by DOT1x                             : 0
Recreate attempted by SISF                              : 0
Recreate attempted by SVC CO                            : 0
Recreate attempted by Unknown module                    : 0
Recreate succeeded post switchover                      : 0
Recreate Failed post switchover                         : 0
Recreate Failure in mmif                                : 0
Recreate Failure in co                                  : 0
Recreate Failure in sanet                               : 0
Recreate Failure in authmgr                             : 0
Recreate Failure in dot1x                               : 0
Recreate Failure in mab                                 : 0
Recreate Failure in sanet_accounting                    : 0
Recreate Failure in sisf                                : 0
Recreate Failure in web auth                            : 0
Recreate Failure in lisp                                : 
Recreate Failure in ipv6                                : 0
Recreate Failure in qos                                 : 0

show wireless band-select

To display the status of the band-select configuration, use the show wireless band-select command in privileged EXEC mode.

show wireless band-select

Syntax Description


This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following is sample output from the show wireless band-select command:

Device# show wireless band-select
Band Select Probe Response    : per WLAN enabling
Cycle Count                  : 2
Cycle Threshold (millisec)   : 200
Age Out Suppression (sec)    : 20
Age Out Dual Band (sec)      : 60
Client RSSI (dBm)            : 80

show wireless client

To see the summary of the classified devices, use the show wireless client command.

show wireless client device {cache | count | summary } | {steering} [chassis {chassis-number | active | standby }]R0

Syntax Description


device	Shows classified devices.
steering	Wireless client steering information
cache	Shows the cached classified device summary.
count	Shows the wireless device count.
summary	Shows the active classified device summary.
`chassis-number`	Chassis number. Valid range is 1–2.
active	Active instance.
standby	Standby instance.
R0	Route-Processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the summary of the classified devices:

Device# show wireless client device summary

show wireless client mac-address

To view detailed information of a client using its mac-address, use the show wireless client mac-addressdetail command.

show wireless client mac-address mac-address detail [ chassis {chassis-number | active | standby} R0]

Syntax Description


`mac-address`	Client MAC address.
`chassis-number`	Chassis number. Valid range is 1–2.
active	Active instance.
standby	Standby instance.
R0	Route-Processor slot 0.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Usage Guidelines

The Client Scan Reports section in the output of the show wireless client mac-address detail is populated only for the following Apple devices:

Any iPhone 7 and running iOS 11.0 or higher
Any iPad after iPad Pro (1st gen, 12.9-inch, 2015) and running iOS 11.0 or higher

Other client devices, even if it supports 802.11k or is Wi-Fi Agile Multiband (MBO) certified, are not currently supported to populate the Client Scan Reports section.

Client ACLs shown under show wireless client mac-address <mac address> detail are ACLs applied on the client in Flexconnect local authentication case with MAB+Web authentication WLAN with AAA override enabled. This is applicable only for Express Wi-Fi by Facebook Policy on Controller. For more information about Facebook policy, see Express Wi-Fi by Facebook.

From Cisco IOS XE Amsterdam 17.3.1 onwards, the controller retains client session for 10 seconds. This feature is applicable for clients in the RUN state and is supported on central authentication with local and flex mode.

In idle state, 10 sec represents idle state timeout and 09 sec represent remaining time out of 10 sec. An example is given below:

Idle state timeout : 10 sec (Remaining time: 09 sec)

Examples

The following example shows how to see detailed client information using its MAC address:

Device# show wireless client mac-address 98-XX-7B-XX-EF-XX detail

show wireless client mac-address (Call Control)

To view call control information related to clients, use the show wireless client mac-address command in privileged EXEC mode.

show wireless client mac-address mac-address call-control call-info

Syntax Description


`mac-address`	The client MAC address.
call-control call-info	Displays the call control and IP-related information about a client.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to display call control and IP-related information about a client:

Device# show wireless client mac-address  30e4.db41.6157 call-control call-info
Client MAC Address        : 30E4DB416157

Call 1 Statistics

Uplink IP Address         : 209.165.200.225
Downlink IP Address       : 209.165.200.226
Uplink Port               : 29052
Downlink Port             : 27538
Call ID                   : c40acb4d-3b3b0.3d27da1e-356bed03
Called Party              : sip:1011
Calling Party             : sip:1012
Priority                  : 6
Call On Hold              : false
Call Duration             : 30

Call 2 Statistics

No Active Call

show wireless client mac-address (TCLAS)

To view information about TCLAS and user priority, use the show wireless client mac-address command in privileged EXEC mode.

show wireless client mac-address mac-address tclas

Syntax Description


`mac-address`	The client MAC address.
tclas	Displays TCLAS and user priority-related information about a client.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to display the TCLAS and user priority-related information about a client:

Device# show wireless client mac-address 30e4.db41.6157 tclas
MAC Address      UP TID Mask Source IP Addr  Dest IP Addr    SrcPort DstPort Proto
----------------------------------------------------------------------------------
30e4.db41.6157    4   4   95 167838052       2164326668      5060     5060      6
30e4.db41.6157    6   1   31 0               2164326668      0        27538    17

show wireless client mac-address mobility history

To see roam history of an active client in subdomain, use the show wireless client mac-address mac-address mobility history command.

show wireless client mac-address mac-address mobility history [chassis {chassis-number | active | standby} R0] | events [ chassis {chassis-number | active | standby} R0] ]

Syntax Description


`mac-address`	MAC address of the client.
`chassis-number`	Chassis number as either 1 or 2.
active R0	Active instance of the client in Route-processor slot 0.
standby R0	Standby instance of the client in Route-processor slot 0.
events	Shows client FSM event history.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

This example shows how to see roam history of an active client in subdomain:

Device# show wireless client mac-address 00:0d:ed:dd:35:80 mobility history

show wireless client summary

To display a summary of active clients associated with the controller, use the show wireless client summary command in privileged EXEC mode.

show wireless client summary

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

The following is sample output from the show wireless client summary command:

Use the show wireless exclusionlist command to display clients on the exclusion list.

Examples

Device# show wireless client summary

Number of Clients: 1    

MAC Address       AP Name                 Type ID  State  Protocol  Method  Role  
--------------------------------------------------------------------------------  
6c40.0899.0466    9115i-r4-sw2-te1-0-37   WLAN 7   Run    11ac      None    Local

show wireless client timers

To display 802.11 system timers, use the show wireless client timers command in privileged EXEC mode.

show wireless client timers

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following is sample output from the show wireless client timers command:

Device# show wireless client timers
 Authentication Response Timeout (seconds)      : 10

show wireless country

To display the configured country and the radio types supported, use the show wireless country command in privileged EXEC mode.

show wireless country {channels | configured | supported [tx-power]}

Syntax Description


channels	Displays the list of possible channels for each band, and the list of channels allowed in the configured countries.
configured	Display configured countries.
supported tx-power	Displays the list of allowed Tx powers in each supported country.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following is sample output from the show wireless country channels command:

Device# show wireless country channels
  Configured Country.............................: US  - United States
      KEY: * = Channel is legal in this country and may be configured manually.
           A = Channel is the Auto-RF default in this country.
           . = Channel is not legal in this country.
           C = Channel has been configured for use by Auto-RF.
           x = Channel is available to be configured for use by Auto-RF.
         (-,-) = (indoor, outdoor) regulatory domain allowed by this country.
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
    802.11bg     :
    Channels     :                   1 1 1 1 1
                 : 1 2 3 4 5 6 7 8 9 0 1 2 3 4
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
 (-A   ,-AB  )  US  :  A * * * * A * * * * A . . .
 Auto-RF         : . . . . . . . . . . . . . .
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
 802.11a         :                         1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
 Channels        : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6
                 : 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
 (-A   ,-AB  )  US  :  . A . A . A . A A A A A * * * * * . . . * * * A A A A *
 Auto-RF         : . . . . . . . . . . . . . . . . . . . . . . . . . . . .
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
 4.9GHz 802.11a  :
   Channels      :                   1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2
                 : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
 US (-A   ,-AB  ): * * * * * * * * * * * * * * * * * * * A * * * * * A
 Auto-RF         : . . . . . . . . . . . . . . . . . . . . . . . . . .
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

The following is sample output from the show wireless country configured command:

Device# show wireless country configured
 Configured Country.............................: US  - United States
 Configured Country Codes
        US  - United States : 802.11a Indoor,Outdoor/ 802.11b / 802.11g

The following is sample output from the show wireless country supported tx-power command:

Device# show wireless country supported tx-power
      KEY: ##    = Tx Power in dBm.
           ##*   = Channel supports radar detection .
           .     = Channel is not legal in this country.
           (-)   = Regulatory Domains allowed by this country.
           (-,-) = (indoor, outdoor) regulatory Domains allowed by this country.
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
    802.11bg     :
    Channels     :                   1 1 1 1 1
                 : 1 2 3 4 5 6 7 8 9 0 1 2 3 4
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
 (-CE  ,-CE  )  AE  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  AL  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-AR  )  AR  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  AT  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-NA  )  AU  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-    )  BA  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  BE  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  BG  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-    )  BH  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-A   )  BO  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-AR  )  BR  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-    )  BY  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-ABN )  CA  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-ABN )  CA2 :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  CH  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-AER ,-AR  )  CL  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  CM  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-CE  ,-CE  )  CN  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-AR  )  CO  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-AB  )  CR  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  CY  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  CZ  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  DE  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  DK  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-ABN )  DO  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-    )  DZ  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-AB  )  EC  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  EE  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  EG  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  ES  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  FI  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  FR  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  GB  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  GI  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  GR  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-NA  )  HK  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-    )  HR  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  HU  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-ER  )  ID  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  IE  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-EI  ,-IE  )  IL  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-I   ,-I   )  ILO :   .  .  .  . 20 20 20 20 20 20 20 20 20  .
 (-A   ,-AN  )  IN  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  IQ  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  IS  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  IT  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-JPU ,-JPU )  J2  :  23 23 23 23 23 23 23 23 23 23 23 23 23 23
 (-JPU ,-JPU )  J3  :  23 23 23 23 23 23 23 23 23 23 23 23 23 23
 (-JPQU,-PQ  )  J4  :  23 23 23 23 23 23 23 23 23 23 23 23 23 23
 (-E   ,-    )  JO  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-JPU ,-JPU )  JP  :  23 23 23 23 23 23 23 23 23 23 23 23 23 23
 (-ACE ,-ACEK)  KE  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  KN  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-ACE ,-ACEK)  KR  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  KW  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  KZ  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  LB  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  LI  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,     )  LK  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  LT  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  LU  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  LV  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  MC  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  ME  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  MK  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,     )  MO  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  MT  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-NA  )  MX  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-ACE ,-AEC )  MY  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  NL  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  NO  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-NA  )  NZ  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  OM  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-AR  )  PA  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-AR  )  PE  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-ABN )  PH  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-ABN )  PH2 :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  PK  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  PL  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-A   )  PR  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  PT  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-A   )  PY  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  QA  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  RO  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  RS  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-AER ,-ER  )  RU  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-AE  ,-AE  )  SA  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  SE  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-SE  )  SG  :  20 20 20 20 20 20 20 20 20 20 20 20 20 20
 (-E   ,-E   )  SI  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  SK  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-ER  )  TH  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  TN  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-EI  ,-E   )  TR  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-ANT )  TW  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  UA  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-A   ,-AB  )  US  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-AB  )  US2 :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-AB  )  USL :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-    )  USX :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-A   )  UY  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-A   ,-AR  )  VE  :  27 27 27 27 27 27 27 27 27 27 27  .  .  .
 (-E   ,-E   )  VN  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .
 (-E   ,-E   )  ZA  :  20 20 20 20 20 20 20 20 20 20 20 20 20  .

show wireless detail

To display the details of the wireless parameters configured, use the show wireless detail command in privileged EXEC mode.

show wireless detail

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

The following parameters are displayed:

The wireless user idle timeout
The controller configured RF group name
Fast SSID change

Examples

The following is sample output from the show wireless detail command:

Device# show wireless detail
User Timeout               : 300
RF network                 : default
Fast SSID                  : Disabled

show wireless dhcp relay statistics

To configure the wireless DHCP relay on the AP, use the show wireless dhcp relay statistic command.

show wireless dhcp relay statistic

Syntax Description


`A.B.C.D`	Indicates the target IPv4 address.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 17.3.1	This command was introduced.

Examples

The following example shows how to configure the wireless DHCP relay on the AP:

Device# show wireless dhcp relay statistics ip-address 10.1.1.1

show wireless dot11h

To see 802.11h configuration details, use the show wireless dot11h command.

show wireless dot11h[ chassis {chassis-number | active | standby} R0]

Syntax Description


`chassis-number`	Chassis number. Valid range is 1–2.
active	Active instance.
standby	Standby instance.
R0	Route-Processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the 802.11h configuration details:

Device# show wireless dot11h

show wireless dtls connections

To display the Datagram Transport Layer Security (DTLS) server status, use the show wireless dtls connections command in privileged EXEC mode.

show wireless dtls connections

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following is sample output from the show wireless dtls connections command:

Device# show wireless dtls connections
 AP Name         Local Port   Peer IP    Peer Port  Ciphersuite
----------------------------------------------------------------------
  AP-2       Capwap_Ctrl   10.0.0.16     52346      TLS_RSA_WITH_AES_128_CBC_SHA
  AP-3       Capwap_Ctrl   10.0.0.17     52347      TLS_RSA_WITH_AES_128_CBC_SHA

show wireless exclusionlist

To see the wireless exclusion list, use the show wireless exclusionlist command.

show wireless exclusionlist [client mac-address client-mac-addr detail ] [ chassis {chassis-number | active | standby} R0]

Syntax Description


`client-mac-addr`	Client MAC address.
`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the configuration in Route-processor slot 0.
standby R0	Standby instance of the configuration in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.
Cisco IOS XE Cupertino 17.9.1	The output of the command was modified to include ARP activity information.

Examples

The following example shows how to see the wireless exclusion list:

Device# show wireless exclusionlist 

Excluded Clients

MAC Address       Description          Exclusion Reason               Time Remaining  
-----------------------------------------------------------------------------------------
10da.4320.cce9                         Client Policy  failure          59

The following example shows the exclusion reason for the clients, which has changed from Client Policy failure to Excess ARP activity from Cisco IOS XE Cupertino 17.9.x onwards:

Device# show wireless exclusionlist 

 
MAC Address       Description         Exclusion Reason                Time Remaining
-------------------------------------------------------------------------------------
6c96.cff2.889a                        Excess ARP activity              53

show wireless exclusionlist client mac-address detail

To see the detailed information for active clients, use the show wireless exclusionlist client mac-address detail command.

show wireless exclusionlist client mac-address client-mac-addr detail

Syntax Description


`client-mac-addr`	Client MAC address.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.
Cisco IOS XE Cupertino 17.9.1	The output of the command was modified to include ARP activity information.

Examples

The following example shows how to see the detailed information for active clients:

Device# show wireless exclusionlist client mac-address 12da.4820.cce9 detail

Client State : Excluded
Client MAC Address : 12da.4820.cce9
Client IPv4 Address: 20.20.20.6
Client IPv6 Address: N/A
Client Username: N/A
Exclusion Reason :  Client Policy  failure
Authentication Method : None
Protocol: 802.11ac
AP MAC Address : 58ac.780e.08f0
AP Name: charlie2
AP slot : 1
Wireless LAN Id : 2
Wireless LAN Name: mhe-ewlc
VLAN Id : 20

The following example shows how to see the detailed information for active clients, where ARP rate limit exclusion that has changed from Client Policy failure to Excess ARP activity from Cisco IOS XE Cupertino 17.9.x onwards is shown:

Device# show wireless exclusionlist client mac-address 6c96.cff2.889a detail
 
Client State : Excluded
Client MAC Address : 6c96.cff2.889a
Client IPv4 Address: N/A
Client IPv6 Address: N/A
Client Username: N/A
Exclusion Reason : Excess ARP activity
Authentication Method : None
Protocol: 802.11ac
AP MAC Address : 4001.7aca.5680
AP Name: AP40CE.2485.D5E8
AP slot : 1
Wireless LAN Id : N/A
VLAN Id : 63

show wireless fabric summary

To view the fabric status, use the show wireless fabric summary command.

show wireless fabric summary

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.
Cisco IOS XE 17.14.1	The output of the command was modified to include IPv6 address.

Examples

This example shows how to view fabric status:

Device# show wireless fabric summary
Fabric Status      : Enabled


Control-plane: 
Name                             IP-address        Key                              Status
--------------------------------------------------------------------------------------------
test-map                         10.12.13.14       test1                            Down 


Fabric VNID Mapping:
  Name               L2-VNID        L3-VNID        IP Address             Subnet        Control plane name
----------------------------------------------------------------------------------------------------------------------
  test1               12             10             10.6.8.9            255.255.255.236    test2

This example shows how to view fabric status for IPv6:

Device# show wireless fabric summary 
Fabric Status      : Enabled


Control-plane: 
Name                                IP-address                                 Key                                 Status
-------------------------------------------------------------------------------------------------------------------------
default-control-plane               2001:192:168:1::3                          cisco123                            Up   


Fabric VNID Mapping:
  Name               L2-VNID       L3-VNID       IP Address                                 Subnet                                     Control plane name
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------
  130_120_0_INFRA    8188          4097          2003:2000:130:120::1                       ffff:ffff:ffff:ffff::                      default-control-plane

show wireless fabric client summary

To see the summary of a fabric enabled wireless client, use the show wireless fabric client summary command.

show wirelessv fabric client summary

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.
Cisco IOS XE 17.14.1	The output of the command was modified to include IPv6 address.

Examples

The following example shows how to see the fabric enabled wireless client summary:

Device# show wireless fabric client summary

The following example shows how to see the fabric enabled wireless client summary for IPv6:

Device# show wireless fabric client summary
Number of Fabric Clients : 2
MAC Address          AP Name              Type      ID     State     Protocol     Method    L2 VNID      RLOC IP         
2c33.7a5b.8fc5     APC4F7.D54D.0B94       WLAN      22      Run       11n(2.4)     None       8190    1100:10:10:10:1:1:1:6 
40ec.995a.434e    APC4F7.D54D.0B94        WLAN      20      Run       11ac         None       8190    1100:10:10:10:1:1:1:6

show wireless fabric vnid mapping

To view all the VNID mapping details, use the show wireless fabric vnid mapping command.

show wireless fabric vnid mapping

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view all the VNID mapping details:

Device# show wireless fabric vnid mapping
Fabric VNID Mapping:
  Name               L2-VNID        L3-VNID        IP Address             Subnet       Control plane name
----------------------------------------------------------------------------------------------------------------------
  test1               12             10             10.6.8.9            255.255.255.236    test2

show wireless flow-control

To display the information about flow control on a particular channel, use the show wireless flow-control command in privileged EXEC mode.

show wireless flow-control channel-id

Syntax Description


`channel-id`	Identification number for a channel through which flow control is monitored.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following is sample output from the show wireless flow-control channel-id command:

Device# show wireless flow-control 3 
Channel Name                           : CAPWAP
FC State                               : Disabled
Remote Server State                    : Enabled
Pass-thru Mode                         : Disabled
EnQ Disabled                           : Disabled
Queue Depth                            : 2048
Max Retries                            : 5
Min Retry Gap (mSec)                   : 3

show wireless flow-control statistics

To display the complete information about flow control on a particular channel, use the show wireless flow-control statistics command in privileged EXEC mode.

show wireless flow-control channel-id statistics

Syntax Description


`channel-id`	Identification number for a channel through which flow control is monitored.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following is sample output from the show wireless flow-control channel-id statistics command:

Device# show wireless flow-control 3 statistics
 Channel Name                                 : CAPWAP
# of times channel went into FC               : 0
# of times channel came out of FC             : 0
Total msg count received by the FC Infra      : 1
Pass-thru msgs send count                     : 0
Pass-thru msgs fail count                     : 0
# of msgs successfully queued                 : 0
# of msgs for which queuing failed            : 0
# of msgs sent thru after queuing             : 0
# of msgs sent w/o queuing                    : 1
# of msgs for which send failed               : 0
# of invalid EAGAINS received                 : 0
Highest watermark reached                     : 0
# of times Q hit max capacity                 : 0
Avg time channel stays in FC (mSec)           : 0

show wireless load-balancing

To display the status of the load-balancing feature, use the show wireless load-balancing command in privileged EXEC mode.

show wireless load-balancing

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following is sample output from the show wireless load-balancing command:

 > show wireless load-balancing
Aggressive Load Balancing............................: per WLAN enabling
Aggressive Load Balancing Window (clients).................:: 5
Aggressive Load Balancing Denial Count.....................:: 3

Statistics
Total Denied Count (clients)................................:: 0
Total Denial Sent (messages)................................:: 0
Exceeded Denial Max Limit Count (times).....................:: 0
None 5G Candidate Count (times).............................:: 0
None 2.4G Candidate Count (times)...........................:: 0

show wireless media-stream client detail

To see the media stream clients information by stream name, use the show wireless media-stream client detail command.

show wireless media-stream client detail

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see media stream clients information by stream name:

Device# show wireless media-stream client detail

show wireless media-stream group

To display the wireless media-stream group information, use the show wireless media-stream group command.

show wireless media-stream group {detail groupName | summary}

Syntax Description


detail `groupName`	Display media-stream group configuration details of the group mentioned in the command.
summary	Display media-stream group configuration summary

Command Default

None

Command Modes

User EXEC mode or Privileged EXEC mode

Usage Guidelines

None.

Examples

The following is a sample output of the show wireless media-stream group detail GRP1 command.

Device#show wireless media-stream group detail GRP1

Device#show wireless media-stream group detail GRP1
Media Stream Name : GRP1
Start IP Address : 234.1.1.1
End IP Address : 234.1.1.5
RRC Parameters:
Avg Packet Size(Bytes) : 1200
Expected Bandwidth(Kbps) : 1000
Policy : Admitted
RRC re-evaluation : Initial
QoS : video
Status : Multicast-direct

Examples

The following is a sample output of the show wireless media-stream group summary command.

Device#show wireless media-stream group summary
Number of Groups:: 1
Stream Name          Start IP                               End IP                     Status
------------------------------------------------------------------------------------------------
GRP1                 234.1.1.1                              234.1.1.5                   Enabled

show wireless media-stream message details

To see the wireless multicast-direct session announcement message details, use the show wireless media-stream message details command.

show wireless media-stream message details

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the wireless multicast-direct session announcement message details:

Device# show wireless media-stream message details

show wireless mobility controller ap

To display the list of access points which have joined the sub-domain, use the wireless mobility controller ap command.

show wireless mobility controller ap

Syntax Description


ap	Show joined Access Point in sub-domain.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Denali 16.3.1	This command was introduced.

Usage Guidelines

None

Examples

This example shows how to list the access points which have joined the sub-domain.

Device#show wireless mobility controller ap
Number of AP entries in the sub-domain     : 2

AP name                           AP radio MAC      Controller IP     Location
------------------------------------------------------------------------------------------------------
bos2kk                            00f2.8c42.f520    default-group     default-group
IosAP1                            34ed.522f.7e60    default-group     default-group

show wireless media-stream multicast-direct state

To see the state of the wireless multicast-direct configuration, use the show wireless media-stream multicast-direct state command.

show wireless media-stream multicast-direct state

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the state of the wireless multicast-direct configuration:

Device# show wireless media-stream multicast-direct state

show wireless mesh ap

To see the mesh AP related information, use the show wireless mesh ap command.

show wireless mesh ap { summary | tree | backhaul }[ chassis {chassis-number | active | standby}R0]

Syntax Description


summary	Shows the summary of all connected mesh APs.
tree	Shows the Mesh AP tree.
backhaul	Shows the mesh APs backhaul info.
`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the configuration in Route-processor slot 0.
standby R0	Standby instance of the configuration in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the summary of all the connected mesh APs:

Device# show wireless mesh ap summary

show wireless mesh ap summary

To see the summary of all connected mesh APs, use the show wireless mesh ap summary command.

show wireless mesh ap summary [ chassis {chassis-number | active | standby} R0]

Syntax Description


summary	Shows the summary of all connected mesh APs.
`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the active AP filters in Route-processor slot 0.
standby R0	Standby instance of the active AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the summary of all connected mesh APs:

Device# wireless mesh ap summary

show wireless mesh ap tree

To see the mesh AP tree, use the show wireless mesh ap tree command.

show wireless mesh ap tree

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following example shows how to view the wireless mesh AP tree:

Device # show wireless mesh ap tree

show wireless mesh ap tree

To see the mesh AP tree, use the show wireless mesh ap tree command.

show wireless mesh ap tree

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following example shows how to view the wireless mesh AP tree:

Device # show wireless mesh ap tree

show wireless mesh cac summary

To view the total number of voice calls and bandwidth utilization of APs in the Mesh network, use the show wireless mesh cac summary command.

show wireless mesh cac summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Usage Guidelines

Examples

This example shows how to display the total number of voice calls and bandwidth utilization of APs in the Mesh network:

Device# show wireless mesh cac summary 


AP Name                           Slot  Radio      BW Used  Call
--------------------------------  ----  ---------  -------  ----
APA023.9FA9.B702                  0     802.11b/g  0        0   
                                  1     802.11a    0        0   
APA023.9FA9.D920                  0     802.11b/g  1140     2   
                                  1     802.11a    0        0   
AP380E.4DBF.C6A6                  0     802.11b/g  0        0   
                                  1     802.11a    0        0   
AP380E.4DBF.C80C                  0     802.11b/g  570      0   
                                  1     802.11a    2144     2   
AP380E.4DBF.C816                  0     802.11b/g  0        0   
                                  1     802.11a    0        0

show wireless mesh config

To see the mesh configurations, use the show wireless mesh config command.

show wireless mesh config [ chassis {chassis-number | active | standby} R0]

Syntax Description


config	Shows the mesh configurations.
`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the active AP filters in Route-processor slot 0.
standby R0	Standby instance of the active AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the mesh configurations:

Device# wireless mesh config

show wireless mesh rrm dca status

To display the status of the last DCA run per radio, use the show wireless mesh rrm dca status command.

show wireless mesh rrm dca status

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC(#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.9.1	This command was introduced.

Examples

This example shows how to display the status of the last DCA run per radio:

Device# show wireless mesh rrm dca status

show wireless mesh neighbor

To see the neighbors of all connected mesh APs, use the show wireless mesh neighbor command.

show wireless mesh neighbor [ chassis {chassis-number | active | standby} R0]

Syntax Description


neighbor	Shows the neighbors of all connected mesh APs.
`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the active AP filters in Route-processor slot 0.
standby R0	Standby instance of the active AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Usage Guidelines

Definition of the field State is as follows:

UPDATED: Adjacency is reachable: communication is symmetric, we can exchange frames with that AP.
NEIGH: Adjacency is parent capable. Local criterion: reachability, strict BGN config, valid cost, potential loops, and so on.
CHILD: Adjacency is actually a child mesh AP (associated to the considered AP).
PARENT: Adjacency is actually the parent mesh AP.
DEFAULT: Adjacency BGN is different than our backhaul configured one.
BLOCK: Adjacency is currently blocklisted due to: auth failures, capwap teardown, and so on.

Examples

The following example shows how to see the neighbors of all connected mesh APs:

Device# show wireless mesh neighbor

AP Name/Radio             Channel   Rate      Link-snr   Flags   State
---------------------------------------------------------------------------------------------------------
 
AP Name : Mesh-AP01
 
54:9f:c6:fa:5c:71         149       auto      0          40                                             
b0:c5:3c:e5:d9:71         149       auto      22         49      UPDATED NEIGH                          
e8:eb:34:d5:88:d1         149       auto      0          40                                             
e8:eb:34:d5:8d:d1         149       auto      18         49      UPDATED CHILD                         
e8:eb:34:d5:94:d1         149       auto      37         4b      UPDATED NEIGH PARENT                   
e8:eb:34:d5:d3:11         149       auto      31         49      UPDATED NEIGH                           
e8:eb:34:d5:d8:91         149       auto      0          41      UPDATED                                
e8:eb:34:d5:da:31         149       auto      18         49      UPDATED NEIGH                          
e8:eb:34:d5:da:51         149       auto      0          1040    DEFAULT                                
e8:eb:34:d5:dc:d1         149       auto      9          49      UPDATED NEIGH                          
e8:eb:34:d5:ef:51         149       auto      0          40                                              
e8:eb:34:d5:f6:51         149       auto      9          49      UPDATED NEIGH                          
e8:eb:34:d5:fd:51         149       auto      21         49      UPDATED NEIGH                          
ec:ce:13:9a:89:91         149       auto      19         49      UPDATED NEIGH                          
ec:ce:13:d7:6f:91         149       auto      18         49      UPDATED NEIGH                          
ec:ce:13:d7:75:71         149       auto      19         49      UPDATED NEIGH                          
ec:ce:13:d7:87:91         149       auto      0          41      UPDATED                                
ec:ce:13:d7:8e:51         149       auto      6          49      UPDATED NEIGH

show wireless profile ap priming summary

To view the summary of priming APs, the show wireless profile ap priming summary command.

show wireless profile ap priming summary

Syntax Description


The command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Cupertino 17.9.1	This command was introduced.

Examples

The following example shows how to view the summary of priming APs:

Device# show wireless profile ap priming summary

show wireless mobility

To view the wireless mobility summary, use the show wireless mobility command.

show wireless mobility { agent mobility-agent-ipclient summary | ap-list ip-address ip-address| controller client summary| dtls connections| statistics summary}

Syntax Description


agent `mobility-agent-ip` client summary	Shows the active clients on a mobility agent.
ap-list ip-address `ip-address`	Shows the list of Cisco APs known to the mobility group.
controller client summary	Shows the active clients in the subdomain.
dtls connections	Shows the DTLS server status.
statistics	Shows the statistics for the Mobility manager.
summary	Shows the summary of the mobility manager.

Command Default

None

Command Modes

Global Configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to display a summary of the mobility manager:

Device (config)# show wireless mobility ap-list

AP name                           AP radio MAC      Controller IP     Learnt from
------------------------------------------------------------------------------------------------------
TSIM_AP-101                       0000.2000.6600    9.9.9.2           Self
TSIM_AP-102                       0000.2000.6700    9.9.9.2           Self
TSIM_AP-103                       0000.2000.6800    9.9.9.2           Self
TSIM_AP-400                       0000.2001.9100    9.9.9.2           Self
TSIM_AP-402                       0000.2001.9300    9.9.9.2           Self
TSIM_AP-403                       0000.2001.9400    9.9.9.2           Self
TSIM_AP-406                       0000.2001.9700    9.9.9.2           Self
TSIM_AP-407                       0000.2001.9800    9.9.9.2           Self
TSIM_AP-409                       0000.2001.9a00    9.9.9.2           Self

show wireless mobility peer ip

To see the details of the mobility peer using its IP address, use the show wireless mobility peer ip command.

show wireless mobility peer ip ip-address

Syntax Description


`ip-address`	Mobility peer IPv4 IP address.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the details of the wireless mobility peer using its IP address:

Device# show wireless mobility peer ip 209.165.200.224

show wireless multicast group summary

To see the wireless multicast group summary, use the show wireless multicast group summary command.

show wireless multicast group summary

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the summary of the wireless multicast group:

Device# show wireless multicast group summary

show wireless mobility summary

To see the wireless mobility manager summary, use the show wireless mobility summary command.

show wireless mobility summary

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the wireless mobility manager's summary:

Device# show wireless mobility summary

show wireless multicast

To display wireless multicast information, use the show wireless multicast command in privileged EXEC mode.

show wireless multicast [ source source-ip group group-ip vlan vlan-id | group group-ip vlan vlan-id]

Syntax Description


source `source-ip`	(Optional) Specifies the source IPv4 and IPv6 address of multicast traffic.
group `group-ip`	(Optional) Specifies the destination group and group IP of mutlicast traffic.
vlan `vlan-id`	Displays the client information on VLAN with the specific VLAN ID.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

None

Examples

This example shows how to display the wireless multicast information:


Device# show wireless multicast

Multicast                               : Enabled
AP Capwap Multicast                     : Unicast
Wireless Broadcast                      : Disabled
Wireless Multicast non-ip-mcast         : Disabled

Vlan        Non-ip-mcast     Broadcast        MGID
------------------------------------------------------
1           Enabled          Enabled          Enabled
2           Enabled          Enabled          Disabled
94          Enabled          Enabled          Disabled
 
Device# show wireless multicast
Multicast                               : Disabled
AP Capwap Multicast                     : Unicast  
Wireless Broadcast                      : Disabled
Wireless Multicast non-ip-mcast         : Disabled
Wireless Multicast link-local           : Enabled

show wireless multicast group

To display the information of the wireless-multicast non-ip VLANs or the group, use the show wireless multicast group command in privileged EXEC mode.

show wireless multicast group {summary | group-ip vlan vlan-id}

Syntax Description


summary	Displays wireless-multicast non-ip group summary.
`group-ip`	Specifies the group IP address.
vlan `vlan-id`	Specifies the destination group IPv4/IPv6 Address of multicast traffic.

Command Default

None.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to display the wireless-multicast non-ip group summary.


Device# show wireless multicast group summary

show wireless mesh ethernet daisy-chain summary

To verify the ethernet daisy chain summary, use the show wireless mesh ethernet daisy-chain summary command.

show wireless mesh ethernet daisy-chain summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.4.1	This command was introduced.

Examples

The following example shows how to verify the ethernet daisy chain summary:

Device# show wireless mesh ethernet daisy-chain summary

AP Name BVI MAC         BGN   Backhaul   Ethernet      STP Red
----------------------------------------------------------------------------------------------------------
RAP4    683b.78bf.15f0  IOT  Ethernet0   Up Up Dn Dn   Enabled
RAP3    683b.78bf.1634  IOT  Ethernet0   Up Up Dn Dn   Enabled
RAP1    6c8b.d383.b4d4  IOT  Ethernet0   Up Up Dn Dn   Enabled
RAP2    6c8b.d383.b4e8  IOT  Ethernet0   Up Up Up Dn   Enabled

show wireless mesh ethernet daisy-chain bgn

To verify the ethernet daisy chain Bridge Group Name (BGN) details, use the show wireless mesh ethernet daisy-chain bgn command.

show wireless mesh ethernet daisy-chain bgn bridge-group-name

Syntax Description


`bridge-group-name`	Enter the bridge group name.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.4.1	This command was introduced.

Examples

The following example shows how to verify the ethernet daisy chain Bridge Group Name (BGN) details:

Device# show wireless mesh ethernet daisy-chain bgn <IOT>

AP Name   BVI MAC       BGN  Backhaul    Ethernet      STP Red
----------------------------------------------------------------------------------------------------------
RAP4    683b.78bf.15f0  IOT  Ethernet0   Up Up Dn Dn   Enabled
RAP3    683b.78bf.1634  IOT  Ethernet0   Up Up Dn Dn   Enabled
RAP1    6c8b.d383.b4d4  IOT  Ethernet0   Up Up Dn Dn   Enabled
RAP2    6c8b.d383.b4e8  IOT  Ethernet0   Up Up Up Dn   Enabled

show wireless performance

To display aggressive load balancing configuration, use the show wireless performance command in privileged EXEC mode.

show wireless performance {ap | client} summary

Syntax Description


ap summary	Displays aggressive load balancing configuration of access points configured to the controller.
client summary	Displays aggressive load balancing configuration details of the clients.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following is sample output from the show wireless performance ap summary command.

Device# show wireless performance ap summary
Number of APs:

The following is sample output from the show wireless performance client summary command.

Device# show wireless performance client summary
Number of Clients:

MAC Address        AP Name           Status        WLAN/Guest-Lan Auth Protocol Port Wired
------------------------------------------------------------------------------------------

show wireless pmk-cache

To display information about the pairwise master key (PMK) cache, use the show wireless pmk-cache command in privileged EXEC mode.

show wireless pmk-cache [mac-address mac-addr]

Syntax Description


mac-address `mac-addr`	(Optional) Information about a single entry in the PMK cache.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following is sample output from the show wireless pmk-cache mac-address command:

Device# show wireless pmk-cache mac-address H.H.H 
Number of PMK caches in total : 0

show wireless probe

To display the advanced probe request filtering configuration and the number of probes sent to the WLAN controller per access point per client and the probe interval in milliseconds, use the show wireless probe command in privileged EXEC mode.

show wireless probe

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following is sample output from the show wireless probe command:

Device# show wireless probe
Probe request filtering                          : Enabled
Number of probes per client per radio fwd from AP: 2
Probe request rate-limiting interval             : 500 msec
Aggregate probe request interval                 : 500 msec

show wireless profile ap priming all

To display the details of priming profiles, use the show wireless profile ap priming all command.

show wireless profile ap priming all

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.9.2	This command was introduced.

Examples

The following example shows how to display the details of priming profiles:

Device# show wireless profile ap priming all

Profile Name  Primary Controller Name  Primary Controller IP  Secondary Controller Name  Secondary Controller IP  Tertiary Controller Name  Tertiary Controller IP  Override
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------
AP-PRIMING-1  BGL18-wlc                209.165.201.1          BGL17-wlc                  209.165.201.2                                       0.0.0.0                Disabled
AP-PRIMING-2  BGL18-wlc                209.165.201.2          BGL17-wlc                  209.165.201.2            BGL12-wlc                  209.165.201.3          Disabled

show wireless profile ap priming all

To display the details of priming profiles, use the show wireless profile ap priming all command.

show wireless profile ap priming all

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.9.2	This command was introduced.

Examples

The following example shows how to display the details of priming profiles:

Device# show wireless profile ap priming all

Profile Name  Primary Controller Name  Primary Controller IP  Secondary Controller Name  Secondary Controller IP  Tertiary Controller Name  Tertiary Controller IP  Override
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------
AP-PRIMING-1  BGL18-wlc                209.165.201.1          BGL17-wlc                  209.165.201.2                                       0.0.0.0                Disabled
AP-PRIMING-2  BGL18-wlc                209.165.201.2          BGL17-wlc                  209.165.201.2            BGL12-wlc                  209.165.201.3          Disabled

show wireless profile airtime-fairness mapping

To view the ATF policy mapping with the wireless profiles, use the show wireless profile airtime-fairness mapping command.

show wireless profile airtime-fairness mapping

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the ATF policy mapping with the wireless profiles:

Device# show wireless profile airtime-fairness mapping
Policy Profile                    Band      ATF Policy                       Weight     Client Sharing    Availability
----------------------------------------------------------------------------------------------------------------------
WGB                               2.4GHz                                      -         -                 No
WGB                               5GHz                                        -         -                 No
Policy1                           2.4GHz                                      -         -                 No
Policy1                           5GHz                                        -         -                 No
Test WBG                          2.4GHz                                      -         -                 No
Test WBG                          5GHz                                        -         -                 No
profile-name                      2.4GHz    atf-policy-name                   5         Enabled           Yes

show wireless profile airtime-fairness summary

To view the summary of air time fairness profiles, use the show wireless profile airtime-fairness summary command.

show wireless profile airtime-fairness summary

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the summary of air time fairness profiles:

Device# show wireless profile airtime-fairness summary
Policy Id      Policy Name                      Weight      Client Sharing
--------------------------------------------------------------------------
1              atf-policy-name                   5           Enabled

show wireless profile ap packet-capture

To view the AP packet capture information, use the show wireless profile ap packet-capture command.

show wireless profile ap packet-capture { detailed profile-name | summary}

Syntax Description


`profile-name`	AP packet capture profile.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

Examples

The following example shows how to view the AP packet capture information:

Device# show wireless profile ap packet-capture summary  
Number of AP packet capture profiles: 3

Profile Name               Buffer   Duration(M Packet Len FTP IP       
----------------------------------------------------------------------
test                        1200        20         0      9.1.0.101    
test1                       2048        10         0      0.0.0.0      
tets1                       1024        10         0      0.0.0.0

Examples

The following example shows how to view the detailed AP packet capture information of an AP profile:

Device# show wireless profile ap packet-capture detailed test1

Profile Name : test1
Description  : 
---------------------------------------------------
Buffer Size       : 2048 KB
Capture Duration  : 10 Minutes
Truncate Length   : packet length
FTP Server IP     : 0.0.0.0
FTP path          : 
FTP Username      : 

Packet Classifiers
  802.11 Control  : Enabled
  802.11 Mgmt     : Enabled
  802.11 Data     : Disabled
  Dot1x           : Disabled
  ARP             : Disabled
  IAPP            : Disabled
  IP              : Disabled
  TCP             : Disabled
  TCP port        : all
  UDP             : Disabled
  UDP port        : all
  Broadcast       : Disabled
  Multicast       : Disabled

show wireless profile calendar-profile detailed

To view the calendar profile details for a specific profile name, use the show wireless profile calendar-profile detailed command.

show wireless profile calendar-profile detailed profile-name

Syntax Description


`profile-name`	Specifies the calendar profile name.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.12.1	This command was introduced.

Examples

This example shows how to view the calendar profile details for a specific profile name:

Device# show wireless profile calendar-profile detailed daily_calendar_profile
Calendar profiles : daily_calendar_profile
------------------------------------------------------------------
Recurrence : DAILY
Start Time : 09:00:00
End Time : 17:00:00

show wireless profile calendar-profile summary

To view the summary of calendar profiles, use the show wireless profile calendar-profile summary command.

show wireless profile calendar-profile summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.12.1	This command was introduced.

Examples

This example shows the summary of calendar profiles:

Device# show wireless profile calendar-profile summary
Number of Calendar Profiles: 3
Profile-Name
---------------------------------
monthly_25_profile
weekly_mon_profile
daily_calendar_profile

show wireless profile fabric detailed

To view the details of a given fabric profile name, use the show wireless profile fabric detailed command.

show wireless profile fabric detailed fabric_profile_name

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the details of a given fabric profile name:

Device# show wireless profile fabric detailed test1
Profile-name      : test-fabric
VNID              : 12
SGT               : 5

show wireless profile flex

To see the flex parameters of an wireless profile, use the show wireless profile flex command.

show wireless profile flex { detailed flex-profile-name chassis {chassis-number | active | standby }R0 } | summary chassis {chassis-number | active | standby}R0}

Syntax Description


detailed	Shows the flex-profile detailed parameters
summary	Show the flex-profile summary.
`chassis-number`	Chassis number. Valid range is 1–2.
active	Active instance.
standby	Standby instance.
R0	Route-Processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the flex parameter's summary of the wireless profile:

Device# show wireless profile flex summary

show wireless profile policy all

To display detailed output of all policy profiles, use the show wireless profile policy all command.

show wireless profile policy all

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privilege EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.12.1	This command was introduced.
Cisco IOS XE Amsterdam 17.3.5	The output of the command was modified to include ARP activity information.

Examples

This example shows how to view the detailed output of all policy profiles:

Device# show wireless profile policy all 

Policy Profile Name                 : policy_name
Description                         : 
Status                              : ENABLED
.
.
.
!the section of the output that shows whether ARP is enabled or disabled in the policy profile.
ARP Activity Limit
  Exclusion                         : ENABLED
  PPS                               : 100
  Burst Interval                    : 5

show wireless profile policy detailed

To display the wireless policy profile details, use the show wireless profile policy detailed command.

show wireless profile policy detailed policy-profile-name

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privilege EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.2.1	This command was introduced.

Examples

This example displays the wireless policy profile details:

Device#show wireless profile policy detailed policy-profile-name

show wireless profile mesh detailed

To verify the mesh profile, use the show wireless profile mesh detailed command.

show wireless profile mesh detailed profile-name

Syntax Description


`profile-name`	Enter the profile name.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.4.1	This command was introduced.

Examples

The following example shows how to verify the mesh profile:

Device# show wireless profile mesh detailed default-mesh-profile

Mesh Profile Name : default-mesh-profile
-------------------------------------------------
Description : default mesh profile
Bridge Group Name : IOT
Strict match BGN : ENABLED
Amsdu : ENABLED
Background Scan : ENABLED
Channel Change Notification : ENABLED
Backhaul client access : ENABLED
Ethernet Bridging : ENABLED
Ethernet Vlan Transparent : DISABLED
Daisy Chain STP Redundancy : ENABLED
Full Sector DFS : ENABLED
IDS : ENABLED
Multicast Mode : In-Out
Range in feet : 12000
Security Mode : EAP
Convergence Method : Standard
LSC only Authentication : DISABLED
Battery State : ENABLED
Authorization Method : eap_methods
Authentication Method : eap_methods
Backhaul tx rate(802.11bg) : auto
Backhaul tx rate(802.11a) : auto

show wireless profile radio summary

To display the wireless radio profile summary, use the show wireless profile radio summary command.

show wireless profile radio summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC mode

Command History


Release	Modification
Cisco IOS XE Bengaluru 17.6.1	This command was introduced.

Usage Guidelines

None

Examples

The following example shows you how to display the wireless radio profile summary:

Device# show wireless profile radio summary

show wireless profile tunnel summary

To display the wireless tunnel-profile summary, use the show wireless profile tunnel summary command.

show wireless profile tunnel summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.11.1	This command was introduced.

Examples

This example shows how to display the wireless tunnel profile summary:

Device# show wireless profile tunnel summary 

Profile Name                     AAA-Override AAA-Proxy DHCP Opt82 Enabled 
-------------------------------- ------------ --------- ---------- --------
eogre_tunnel                               No        No        Yes      Yes
eogre_tunnel_set                           No        No        Yes       No
eogre_tunnel_snmp                          No        No         No       No

show wireless redundancy statistics

To see the high availability statistics, use the show wireless redundancy statistics command.

show wireless redundancy statistics {ap-group | wncdallchassis {chassis-num | active | standby}R0} {ap-recovery | {instance-id | all | chassis {chassis-num | active | standby}R0}} {client-group | wncdallchassis {chassis-num | active | standby}R0} {client-recovery | {mobilityd | sisf}chassis {chassis-num | active | standby}R0} {wncd | {instance-id | all | chassis {chassis-num | active | standby}R0}}

Syntax Description


`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the configuration in Route-processor slot 0.
standby R0	Standby instance of the configuration in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see all the statistics for WNCD :

show wireless rfid

To display RFID tag information, use the show wireless rfid command in privileged EXEC mode.

show wireless rfid { client | detail rfid-mac-address | stats | summary}

Syntax Description


client	Displays the summary of RFID tags that are clients.
detail	Displays information about a particular RFID tag.
stats	Displays RFID statistics.
summary	Displays summary information for all known RFID tags.
`rfid-mac-address`	RFID MAC address.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view RFID information:

Device# show wireless rfid summary 

Total RFID entries: : 16
Total Unique RFID entries : 16
RFID ID VENDOR Closet AP RSSI Time Since Last Heard
0012.b80a.c791 Cisco 7069.5a63.0520 -31 1 minute 40 seconds ago
0012.b80a.c953 Cisco 7069.5a63.0460 -33 2 minutes 15 seconds ago
0012.b80b.806c Cisco 7069.5a63.0260 -45 22 seconds ago
0012.b80d.e9f9 Cisco 7069.5a63.0460 -38 2 minutes 37 seconds ago
0012.b80d.ea03 Cisco 7069.5a63.0520 -43 2 minutes 38 seconds ago
0012.b80d.ea6b Cisco 7069.5a63.0460 -39 2 minutes 35 seconds ago
0012.b80d.ebe8 Cisco 7069.5a63.0520 -43 1 minute 31 seconds ago
0012.b80d.ebeb Cisco 7069.5a63.0520 -43 2 minutes 37 seconds ago
0012.b80d.ec48 Cisco 7069.5a63.0460 -42 2 minutes 16 seconds ago
0012.b80d.ec55 Cisco 7069.5a63.0520 -41 1 second ago

show wireless stats ap name

To display the wireless AP BSSID statistics, use the show wireless stats ap name ap-name dot11 24ghz slot 0 wlan-name 1-4096 statistics

show wireless stats ap name ap-name dot11 24ghz slot 0 wlan-name 1-4096 statistics

Syntax Description


`ap-name`	Specifies the name of the AP.
`wlan-name`	Specifies the name of the WLAN.
`wlan-id`	Specifies the WLAN ID. The value range is 1 to 4096.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.2.1	This command was introduced.

Examples

This example show how to display the wireless AP BSSID statistics:

Device#show wireless stats ap name ap-name dot11 24ghz slot 0 wlan-name  1-4096 statistics 
BSSID                  : 7069.5a38.112e
WLAN ID                : 18
Client Count           : 1
TX Statistics
-------------------------------------------------------------------------------
Mgmt          Retries      Data Bytes      Data Retries       Subframe Retries 
-------------------------------------------------------------------------------
12            18           16081           18                 0                
RX Statistics
-------------------------------------------------------------------------------
Mgmt          Data Bytes                                                       
-------------------------------------------------------------------------------
74            17693
Data Distribution
-------------------------------------------------------------------------------
Bytes                       RX                         TX                      
-------------------------------------------------------------------------------
0-64                        55                         93                      
65-128                      66                         40                      
129-256                     21                         5                       
257-512                     10                         3                       
513-1024                    1                          9                       
1025-2048                   0                          1                       
2049-4096                   0                          0                       
4097-8192                   0                          0                       
8193-16384                  0                          0                       
16385-32768                 0                          0                       
32769-65536                 0                          0                       
65537-131072                0                          0                       
131073-262144               0                          0                       
262145-524288               0                          0                       
524289-1048576              0                          0                       
WMM Statistics
-------------------------------------------------------------------------------
                            RX                         TX                           
-------------------------------------------------------------------------------
Voice                       0                          43                      
Video                       0                          0                       
Best Effort                 154                        39                      
Background                  0                          0                       
MCS
-------------------------------------------------------------------------------
MCS                         RX                         TX                   
-------------------------------------------------------------------------------
mcs0                        39                          0                     
mcs1                        2                           0                     
mcs2                        5                           0                     
mcs3                        7                           0                     
mcs4                        25                          0                     
mcs5                        59                          0                     
mcs6                        290                         0                     
mcs7                        1148                        3                     
mcs8                        2288                        0                     
mcs9                        4440                        2

show wireless stats client delete reasons

To verify total client delete reasons, use the show wireless stats client delete reasons command.

show wireless stats client delete reasons

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC(#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.1.1	This command was introduced.

Examples

This example shows how to verify the total client delete reasons:

Device# show wireless stats client delete reasons

Total client delete reasons
---------------------------
Controller deletes
---------------------------
---------------------------
No Operation                                                    : 0
Unknown                                                         : 0
Session Manager                                                 : 0
Connection timeout                                              : 0
Datapath plumb                                                  : 0
WPA key exchange timeout                                        : 0
802.11w MAX SA queries reached                                  : 0
Client deleted during HA recovery                               : 0
Inter instance roam failure                                     : 0
Inter instance roam success                                     : 0
Inter controller roam success                                   : 0
Due to mobility failure                                         : 0
NAS error                                                       : 0
Policy Manager internal error                                   : 0
80211v smart roam failed                                        : 0
DOT11v association failed                                       : 0
DOT11r pre-authentication failure                               : 0
SAE authentication failure                                      : 0
DOT11 failure                                                   : 0
DOT11 SAE invalid message                                       : 0
DOT11 denied data rates                                         : 0
802.11v Client RSSI lower than the association RSSI threshold   : 0
invalid QoS parameter                                           : 0
DOT11 IE validation failed                                      : 0
DOT11 group cipher in IE validation failed                      : 0
DOT11 invalid pairwise cipher                                   : 0
DOT11 invalid AKM                                               : 0
DOT11 unsupported RSN version                                   : 0
DOT11 invalid RSNIE capabilities                                : 0
DOT11 received invalid PMKID in the received RSN IE             : 0
DOT11 received invalid PMK length                               : 0
DOT11 invalid MDIE                                              : 0
DOT11 invalid FT IE                                             : 0
DOT11 AID allocation conflicts                                  : 0
AVC client re-anchored at the foreign controller                : 0
Client EAP ID timeout                                           : 0
Client DOT1x timeout                                            : 0
Malformed EAP key frame                                         : 0
EAP key install bit is not expected                             : 0
EAP key error bit is not expected                               : 0
EAP key ACK bit is not expected                                 : 0
Invalid key type                                                : 0
EAP key secure bit is not expected                              : 0
key description version mismatch                                : 0
wrong replay counter                                            : 0
EAP key MIC bit expected                                        : 0
MIC validation failed                                           : 0
MAC theft                                                       : 0
IP theft                                                        : 0
Policy bind failure                                             : 0
Web authentication failure                                      : 0
802.1X authentication credential failure                        : 0
802.1X authentication timeout                                   : 0
802.11 authentication failure                                   : 0
802.11 association failure                                      : 0
Manually excluded                                               : 0
DB error                                                        : 0
Anchor creation failure                                         : 0
Anchor invalid Mobility BSSID                                   : 0
Anchor no memory                                                : 0
Call admission controller at anchor node                        : 0
Supplicant restart                                              : 0
Port admin disabled                                             : 0
Reauthentication failure                                        : 0
Client connection lost                                          : 0
Error while PTK computation                                     : 0
MAC and IP theft                                                : 0
QoS policy failure                                              : 0
QoS policy send to AP failure                                   : 0
QoS policy bind on AP failure                                   : 0
QoS policy unbind on AP failure                                 : 0
Static IP anchor discovery failure                              : 0
VLAN failure                                                    : 0
ACL failure                                                     : 0
Redirect ACL failure                                            : 0
Accounting failure                                              : 0
Security group tag failure                                      : 0
FQDN filter definition does not exist                           : 0
Wrong filter type, expected postauth FQDN filter                : 0
Wrong filter type, expected preauth FQDN filter                 : 0
Invalid group id for FQDN filter valid range  1..16             : 0
Policy parameter mismatch                                       : 0
Reauth failure                                                  : 0
Wrong PSK                                                       : 0
Policy failure                                                  : 0
AAA server unavailable                                          : 0
AAA server not ready                                            : 0
No dot1x method configuration                                   : 0
Association connection timeout                                  : 0
MAC-AUTH connection timeout                                     : 0
L2-AUTH connection timeout                                      : 0
L3-AUTH connection timeout                                      : 0
Mobility connection timeout                                     : 0
static IP connection timeout                                    : 0
SM session creation timeout                                     : 0
IP-LEARN connection timeout                                     : 0
NACK IFID exists                                                : 0
Guest-LAN invalid MBSSID                                        : 0
Guest-LAN no memory                                             : 0
Guest-LAN ceate request failed                                  : 0
EoGRE Reset                                                     : 0
EoGRE Generic Join Failure                                      : 0
EoGRE HA-Reconciliation                                         : 0
Wired idle timeout                                              : 0
IP Update timeout                                               : 0
SAE Commit received in Associated State                         : 0
NACK IFID mismatch                                              : 0
EoGRE Invalid VLAN                                              : 0
EoGRE Empty Domain                                              : 0
EoGRE Invalid Domain                                            : 0
EoGRE Domain Shut                                               : 0
EoGRE Invalid Gateway                                           : 0
EoGRE All Gateways down                                         : 0
EoGRE Flex - no active gateway                                  : 0
EoGRE Rule Matching error                                       : 0
EoGRE AAA Override error                                        : 0
EoGRE client onboarding error                                   : 0
EoGRE Mobility Handoff error                                    : 0
L3 VLAN Override connection timeout                             : 0
Delete received from AP                                         : 0
QoS failure                                                     : 0
WPA group key update timeout                                    : 0
DOT11 unsupported client capabilities                           : 0
DOT11 association denied unspecified                            : 0
DOT11 AP have insufficient bandwidth                            : 0
DOT11 invalid QoS parameter                                     : 0
Client not allowed by assisted roaming                          : 0
Wired client deleted due to WGB delete                          : 0
Client Abort                                                    : 0
Mobility peer delete                                            : 0
No IP                                                           : 0
BSSID down                                                      : 0
DOT11 QoS policy                                                : 0
Roam across policy profile deny                                 : 0
4WAY handshake failure - M1 issue                               : 0
4WAY handshake failure - M3 issue                               : 0
Exclusion policy template fail                                  : 0
DOT11 Cipher Suite Rejected                                     : 0
WLAN-ID mismatch in access accept failures                      : 0
EasyPSK AAA unknown error                                       : 0
EasyPSK unspecified error                                       : 0
EasyPSK PSK mismatch error                                      : 0
EasyPSK radius busy error                                       : 0
EasyPSK limit reached error                                     : 0
EasyPSK bad 802.1X frame error                                  : 0
EasyPSK missing parameter error                                 : 0
Supplicant name failure                                         : 0
User name failure                                               : 0
Service set ID failure                                          : 0
Anchor VLAN ID failure                                          : 0
PSK failure                                                     : 0
PSK mode failure                                                : 0
Interim interval failure                                        : 0
Link-local bridging VLAN failure                                : 0
Link-local bridging VLAN failure                                : 0
Maximum client limit reached on AP                              : 0
Maximum client limit reached on AP per wlan                     : 0
Maximum client limit reached on AP radio per wlan               : 0
Maximum client limit reached on AP radio                        : 0
L3 Access Roam across policy profile deny                       : 0
L3 Access Inter controller roam deny                            : 0
----------------------------
Informational Delete Reason
-----------------------------
Mobility WLAN down                                              : 0
AP upgrade                                                      : 0
L3 authentication failure                                       : 0
AP down/disjoin                                                 : 0
MAC authentication failure                                      : 0
Due to SSID change                                              : 0
Due to VLAN change                                              : 0
Admin deauthentication                                          : 0
Session timeout                                                 : 0
Idle timeout                                                    : 0
Supplicant request                                              : 0
Mobility tunnel down                                            : 0
DOT11v timer timeout                                            : 0
DOT11 max STA                                                   : 0
IAPP disassociation for wired client                            : 0
Wired WGB change                                                : 0
Wired VLAN change                                               : 0
WGB Wired client joins as a direct wireless client              : 0
Incorrect credentials                                           : 0
Wired client cleanup due to WGB roaming                         : 0
Radio Down                                                      : 0
Mobility failure on fast roam                                   : 0
Due to IP Zone change                                           : 0
Access denied due to Locally Administered MAC Address           : 0
-----------------------------
-----------------------------
Client initiate delete
-----------------------------
Deauthentication or disassociation request                      : 0
Client DHCP                                                     : 0
Client EAP timeout                                              : 0
Client 8021x failure                                            : 0
Client device idle                                              : 0
Client captive portal security failure                          : 0
Client decryption failure                                       : 0
Client interface disabled                                       : 0
Client user triggered disassociation                            : 0
Client miscellaneous reason                                     : 0
Unknown                                                         : 0
Client peer triggered                                           : 0
Client beacon loss                                              : 0
STA triggered PMK timeout                                  : 0
Excess ARP activity                                        : 0
Excess NDP activity                                        : 0
Unspecified QOS failure                                        : 0
Dpath encode failed                                            : 0
VRF-VLAN mismatch failures                                    : 0
-----------------------------
AP Deletes
-----------------------------
When client is sending disassociation                      : 0
Idle timeout                                               : 0
Client ACL mismatch                                        : 0
AP authentication stop                                     : 0
Association expired at AP                                  : 0
4-way handshake failed                                     : 0
DHCP timeout                                               : 0
Reassociation timeout                                      : 0
SA query timeout                                           : 0
Intra AP roam                                              : 0
Channel switch at AP                                       : 0
Bad AID                                                    : 0
AP requests for client deletion                            : 0
Interface reset                                            : 0
All on slot                                                : 0
Link to client has changed and uplink can be reaper        : 0
Slot disable                                               : 0
MIC failure                                                : 0
VLAN delete                                                : 0
Channel change                                             : 0
Stop reassociation                                         : 0
Packet maximum retry                                       : 0
Transmission deauthentication                              : 0
Sensor station timeout                                     : 0
Age timeout                                                : 0
Transmission threshold fail                                : 0
Uplink receive timeout                                     : 0
Sensor scan next radio                                     : 0
Sensor scan other BSSID                                    : 0
Authentication timeout and web-auth timeout                : 0
Sending deauthentication packet to client                  : 0
AP IP learn timeout                                        : 0
Flex group change                                          : 0
EAPOL log off                                              : 0
EAP request timeout                                        : 0
4way handshake failure                                     : 0
MIC validation                                             : 0
Wrong replay counter                                       : 0
AP tunnel down                                             : 0
Inter roam                                                 : 0
Unknown client                                             : 0
Reauthentication timeout                                   : 0
Continuous idle timeout                                    : 0
RLDP cleanup                                               : 0
Intra-switch roam                                          : 0
PEM cleanup                                                : 0
RLAN Central switch                                        : 0
RLAN data path add failure                                 : 0
RLAN Delete                                                : 0
RLAN Inactive timeout                                      : 0
RLAN MAB failure                                           : 0
CLSM No memory counter                                     : 0
CLSM BSSID mismatch                                        : 0
CLSM No ACL found                                          : 0
CLSM no parent WGB found                                   : 0
CLSM Key plumb faiure                                      : 0
CLSM Mesh key plumb failure                                : 0
CLSM data path add fail                                    : 0
CLSM Authentication response reject                        : 0
CLSM Authentication response send failure                  : 0
CLSM Association response send failure                     : 0
CLSM association response failure with status              : 0
CLSM Webauth timer expired                                 : 0
CLSM Dot1x timer expired                                   : 0
CLSM deauthentication and disassociation send failure      : 0
Driver event Class3 received                               : 0
Driver event PsPoll when not authenticated                 : 0
Driver event ioctl error                                   : 0
Flex FT failure                                            : 0
CLSM driver add failure                                    : 0
Driver client not found                                    : 0
Driver management packet allocation failure                : 0
Driver invalid cipher                                      : 0
Driver invalid association identifier                      : 0
Driver invalid key                                         : 0
Driver firmware set key failure                            : 0
Driver found invalid HT VHT rates                          : 0
Driver found invalid legacy rates                          : 0
Driver found no overlapping legacy rates                   : 0
Driver found maximum VHT streams                           : 0
Driver found association identifer in use                  : 0
Driver found too many association requests                 : 0
Driver found cipher attach failure                         : 0
Driver found algorithm mismatch                            : 0
Driver found invalid key length                            : 0
Driver found invalid key index                             : 0
Driver rejected association due to authentication failure  : 0
Driver found client addition to internal records failure   : 0
Driver found client association entry failure              : 0
Driver found client additions to firmware failure          : 0
Driver related internal failure                            : 0
AP limiting maximum client per AP                          : 0
AP limiting maximum client per AP radio per wlan           : 0
AP limiting maximum client per AP radio                    : 0
-------------------
PC Analytics stats:
----------------------------------------
Report Type            Processed Reports
----------------------------------------
 PC_STA_INFO          : 0
 PC_NEIGH_INFO        : 0
 PC_LOW_RSSI          : 0
 PC_TEMP_DISCONN      : 0
 PC_AP_FAILURE        : 0
 PC_UNKNOWN_AP        : 0
--------------------------------------
Report Type            Dropped Reports
--------------------------------------
 PC_STA_INFO          : 0
 PC_NEIGH_INFO        : 0
 PC_LOW_RSSI          : 0
 PC_TEMP_DISCONN      : 0
 PC_AP_FAILURE        : 0
 PC_UNKNOWN_AP        : 0

show wireless statistics mobility

To see the wireless mobility manager statistics, use the show wireless stats mobility command.

show wireless stats mobility {dtls | messages} [ chassis {chassis-number | active | standby} R0]

Syntax Description


dtls	View the mobility dtls messages statistics.
messages	View the mobility messages statistics.
`chassis-number`	Enter the chassis number as either 1 or 2.
active	Active instance of the configuration in Route-processor slot 0.
standby	Standby instance of the configuration in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the statistics of the wireless mobiliy manager:

Device# show wireless stats mobility

show wireless stats mesh packet error

To see the packet statistics of all connected mesh APs, use the show wireless stats mesh packet error command.

show wireless stats mesh packet error [ chassis {chassis-number | active | standby} R0]

Syntax Description


packet	Shows packet statistics information.
error	Shows packet statistics of all connected mesh APs.
active R0	Active instance of the active AP filters in Route-processor slot 0.
standby R0	Standby instance of the active AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the packet error statistics of all connected mesh APs:

Device# show wireless stats mesh packet error

show wireless stats pmk-propagation

To view the PMK propagation statistics on the Cisco wireless controller, use the show wireless stats pmk-propagation command in privileged EXEC mode.

show wireless stats pmk-propagation

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.8.1	This command was introduced.

Examples

The following example shows the PMK propagation statistics on the Cisco Wireless controller:

Device# show wireless stats pmk-propagation

Site-Tag       Bulk Sync Success     Bulk Sync Failure     Incremental Sync Failure
-----------------------------------------------------------------------------------
flex-site-tag       97                       0                   0

show wireless stats mesh security and queue

To see the mesh queue and security statistics of all connected mesh APs, use the show wireless stats mesh command.

show wireless stats mesh {security | queue} [ chassis {chassis-number | active | standby} R0]

Syntax Description


queue	Shows queue statistics of all connected mesh APs.
security	Shows security statistics of all connected mesh APs.
`chassis-number`	Enter the chassis number as either 1 or 2.
active R0	Active instance of the active AP filters in Route-processor slot 0.
standby R0	Standby instance of the active AP filters in Route-processor slot 0.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the security statistics of all connected mesh APs:

Device# show wireless stats mesh security

show wireless stats client detail

To verify the statistics about client, use the show wireless stats client detail command.

show wireless stats client detail

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.1.1	This command was introduced.

Examples

This example shows how to verify the statistics about client:

Device# show wireless stats client detail
[…]
Total L3 VLAN Override vlan change received : 1
Total L3 VLAN Override disassociations sent : 1
Total L3 VLAN Override re-associations received : 1
Total L3 VLAN Override successful VLAN change : 1
[…]
L3 VLAN Override connection timeout : 0

show wireless stats redundancy config database

To view the high availabilty redundancy configuration statistics, use the show wireless stats redundancy config database command.

show wireless stats redundancy config database { mobility | nmspd | rrm | wncd | wncmgrd } instance-id chassis { chassis-num | active | standby } R0

Syntax Description


mobility	Specifes the statistics of Mobilityd configuration database.
nmspd	Specifes the statistics of NMSPD configuration database.
rrm	Specifes the statistics of RRM configuration database.
wncd	Specifes the statistics of WNCD configuration database.
wncmgrd	Specifes the statistics of WNCD configuration database.
`instance-id`	Instance ID. Valid values range from 0 to 7.
chassis	Specifies the chassis.
`chassis-num`	Chassis number.
active	Specifies the active instance.
standby	Specifies the standby instance.
R0	Specifies the route processor slot.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Cupertino 17.7.1	This command was introduced.

Examples

The following example shows how to view the high availabilty redundancy configuration statistics:

Device# show wireless stats redundancy config database wncd 0 chassis 1 R0 

Wncd Configuration Sync Statistics
 Index   Number of Locks    Duration(sec)   Threshold-count   Max-Duration(nsec)
--------------------------------------------------------------------------------
    1        535                127               1           1112156700

show wireless summary

To display the number of access points, radios and wireless clients known to the controller, use the show wireless summary command in privileged EXEC mode.

show wireless summary

Syntax Description

This command has no arguments or keywords.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

The following is sample output from the show wireless summary command:

Device# show wireless summary

Access Point Summary

               Total    Up    Down
-----------------------------------
802.11a/n          2     2       0
802.11b/g/n        2     2       0
All APs            2     2       0

Client Summary

Current Clients : 1
Excluded Clients: 0
Disabled Clients: 0

show wireless urlfilter details

To view the details of a specified wireless URL filter, use the show wireless urlfilter details command.

show wireless urlfilter details list-name

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the details of a specified wireless URL filter:

Device# show wireless urlfilter details urllist_flex_preauth
List Name................. : urllist_flex_preauth
Filter ID............... : : 1
Filter Type............... : PRE-AUTH
Action.................... : PERMIT
Redirect server ipv4...... : 8.8.8.8
Redirect server ipv6...... : 2001:0300:0008:0000:0000:0000:0000:0081
Configured List of URLs
   URL.................... : url1.dns.com

show wireless urlfilter summary

To view the summary of all wireless URL filters, use the show wireless urlfilter summary command.

show wireless urlfilter summary

Syntax Description


This command has no arguments.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Examples

This example shows how to view the summary of all wireless URL filters:

Device# show wireless urlfilter summary
Black-list    - DENY
White-list    - PERMIT
Filter-Type   - Specific to Local Mode

URL-List                         ID  Filter-Type  Action   Redirect-ipv4  Redirect-ipv6
-------------------------------------------------------------------------------------------------------------
urllist_flex_preauth             1    PRE-AUTH     PERMIT    8.8.8.8       2001:0300:0008:0000:0000:0000:0000:0081

show wireless vlan details

To see the VLAN details, use the show wireless vlan details command.

show wireless vlan details [ chassis {chassis-number | active | standby} R0]

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the VLAN details:

Device# show wireless vlan details chassis active r0

show wireless wgb mac-address

To view all the clients of the wireless workgroup bridge (WGB) using its MAC address, use the show wireless wgb mac-address command.

show wireless wgb mac-address mac-address detail

Syntax Description


`mac-address`	MAC address of the WGB.
detail	View clients of the wireless WGB.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the clients of the wireless WGB:

Device# show wireless wgb mac-address 98-C7-7B-09-EF-ED detail

show wireless wgb summary

To see the active workgroup bridges (WGB), use the show wireless wgb summary command.

show wireless wgb summary

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the active workgroup bridges (WGB):

Device# show wireless wgb summary

show wireless wps mfp ap summary

To verify, if access points support Management Frame Protection (MFP) validation and protection, use the show wireless wps mfp ap summary command.

show wireless wps mfp ap summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.12.1	This command was introduced.

Examples

This example shows the access points that support MFP validation and protection:

Device# show wireless wps mfp ap summary
AP Name                          Radio MAC                Validation            Protection
------------------------------------------------------------------------------------------
AP002A.1087.CBF4                 00a2.eefd.bdc0           Enabled               Enabled   
AP58AC.78DE.9946                 00a2.eeb8.4ae0           Enabled               Enabled   
APb4de.3196.caac                 4c77.6d83.6b90           Enabled               Enabled

show wireless wps mfp statistics

To view the Management Frame Protection (MFP) statistics, use the show wireless wps mfp statistics command.

show wireless wps mfp statistics

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.12.1	This command was introduced.

Examples

This example shows the Management Frame Protection (MFP) statistics:

Device# show wireless wps mfp statistics
BSSID          Radio DetectorAP                       LastSourceAddr Error           Count     FrameTypes

aabb.ccdd.eeff a     AP3800                           aabb.ccdd.eeff Invalid MIC     10        Beacon, Probe Response
                                                                     Invalid MIC     20        Beacon, Probe Response

show wireless wps mfp summary

To view the detailed information of Management Frame Protection (MFP), use the show wireless wps mfp summary command.

show wireless wps mfp summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.12.1	This command was introduced.

Examples

This example shows the detailed information of Management Frame Protection (MFP):

Device# show wireless wps mfp summary
Management Frame Protection
  Global Infrastructure MFP state : Enabled
  AP Impersonation detection      : Disabled
  Key refresh interval            : 15

show wireless wps rogue

To see the Rogue AP and Client information, use the show wireless wps rogue command.

See Adhoc Rogues (IBSS) information

show wireless wps rogue {adhoc | {detailed | mac-addr} | summary}

See rogue AP information

show wireless wps rogueap {clientsmac-addr | customsummary | detailedmac-addr | friendlysummary | listmac-addressmac-addr | malicious summary | summary | unclassifiedsummary | rldp {summary | in-progress | detailedrogue-ap-mac-addr}}

See rogue auto-containment information

show wireless wps rogueauto-contain

See rogue client information

show wireless wps rogueclient {summary | detailedmac-addr}

See rogue ignore list

show wireless wps rogueignore-list

See classification rule information

show wireless wps roguerule {detailedrule-name | summary}

See statistics about rogue feature

show wireless wps roguestats [internal]

Syntax Description


`mac-address`	MAC address of the client.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced in a release earlier than Cisco IOS XE Gibraltar 16.10.1.

Examples

The following example shows how to see the rogue feature statistics:

Device# show wireless wps rogue stats

show wireless wps rogue ap summary

To display a list of all rogue access points detected by the device, use the show wireless wps rogue ap summary command.

show wireless wps rogue ap summary

Command Default

None.

Command Modes

Privileged EXEC

Command History


Release	Modification
	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to display a list of all rogue access points detected by the device:


Device# show wireless wps rogue ap summary 
Rogue Location Discovery Protocol            : Disabled
Rogue on wire Auto-Contain                   : Disabled
Rogue using our SSID Auto-Contain            : Disabled
Valid client on rogue AP Auto-Contain        : Disabled
Rogue AP timeout                             : 1200
Rogue Detection Report Interval              : 10
Rogue AP minimum RSSI                        : -128
Rogue AP minimum transient time              : 0

Number of rogue APs detected : 624

MAC Address         Classification     # APs    # Clients   Last Heard
--------------------------------------------------------------------------------------
0018.e78d.250a      Unclassified       1        0           Thu Jul 25 05:04:01 2013
0019.0705.d5bc      Unclassified       1        0           Thu Jul 25 05:16:26 2013
0019.0705.d5bd      Unclassified       1        0           Thu Jul 25 05:10:28 2013
0019.0705.d5bf      Unclassified       1        0           Thu Jul 25 05:16:26 2013

show wireless wps rogue client detailed

To view the detailed information of a specific rogue client, use the show wireless wps rogue client detailed client-mac command.

show wireless wps rogue client detailed client-mac

Syntax Description


`client-mac`	MAC address of the rogue client.

Command Default

None.

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to display the detailed information for a specific rogue client:


Device# show wireless wps rogue client detail  0024.d7f1.2558 
Rogue BSSID                       : 64d8.146f.379f
Rogue Radio Type                  : 802.11n - 5GHz
State                             : Alert
First Time Rogue was Reported     : Wed Aug  7 12:51:43 2013
Last Time Rogue was Reported      : Wed Aug  7 12:51:43 2013
Reported by
  AP 2
    MAC Address                   : 3cce.7309.0370
    Name                          : AP3502-talwar-ccie
    Radio Type                    : 802.11a
    RSSI                          : -42 dBm
    SNR                           : 47 dB
    Channel                       : 52
    Last reported by this AP      : Wed Aug  7 12:51:43 2013

show wireless wps rogue ap detailed

To view the detailed information of a rogue access point, use show wireless wps rogue ap detailed mac-address command.

show wireless wps rogue ap detailed 0008.30a7.7797

Syntax Description

mac-address

The MAC address of the rogue access point.

Note

If a rogue access point uses dot11n on 2.4GHz, the command output displays the radio type as dot11g , dot11n - 2.4 GHz.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Fuji 16.7.x	This command was introduced.

Examples

This example shows how to display the detailed information about a rogue access point:

Device# wireless wps rogue ap detailed 0008.30a7.7797
Rogue Event history

Rogue BSSID                            : 0008.30a7.7797
Is Rogue on Wired Network              : No
Classification                         : Unclassified
Manually Contained                     : Yes
State                                  : Contained Pending
Containment Level                      : 1
Number of Containing APs               : 0
First Time Rogue was Reported          : 03/08/2017 17:41:55
Last Time Rogue was Reported           : 03/08/2017 21:48:34

Number of clients                      : 0

Reported By
  AP Name : JEWLC-AA
    MAC Address                        : 00d7.8f4e.7240
    Detecting slot ID                  : 0
    Radio Type                         : dot11g , dot11n - 2.4 GHz
    SSID                               : psk
    Channel                            : 5
    Channel Width                      : 20 MHz
    RSSI                               : -128 dBm
    SNR                                : 0 dB
    Encryption                         : Enabled
    ShortPreamble                      : Disabled
    WPA Support                        : Not Friendly
    Last reported by this AP           : 03/08/2017 21:48:34

show wireless wps rogue client summary

To display summary of WPS rogue clients, use the show wireless wps rogue client summary command.

show wireless wps rogue client summary

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.10.1	This command was introduced.

Usage Guidelines

Examples

The following displays the output of the show wireless wps rogue client summary command:

Device# show wireless wps rogue client summary
Validate rogue clients against AAA  : Disabled
Validate rogue clients against MSE  : Enabled
Number of rogue clients detected : 0

show wireless wps summary

To view the detailed information of wps, use the show wireless wps summary command.

show wireless wps summary

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
Cisco IOS XE Gibraltar 16.12.1	This command was introduced.
Cisco IOS XE Amsterdam 17.3.5	The output of the command was modified to include ARP activity information.

Examples

This example shows if the Management Frame Protection (MFP) is enabled or disabled:

Device# show wireless wps summary

Client Exclusion Policy
  Excessive 802.11-association failures   : unknown
  Excessive 802.11-authentication failures: unknown
  Excessive 802.1x-authentication         : unknown
  IP-theft                                : unknown
  Excessive Web authentication failure    : unknown
  Failed Qos Policy                       : unknown

Management Frame Protection
  Global Infrastructure MFP state : Enabled
  AP Impersonation detection      : Disabled
  Key refresh interval            : 15

This example shows whether rate limiting is enabled for ARP packets:

Device# show wireless wps summary

Client Exclusion Policy
  Excessive 802.11-association failures   : Enabled
  Excessive 802.1x-authentication         : Enabled
  Mac and IP-theft                        : Enabled
  Excessive Web authentication failure    : Enabled
  Failed Qos Policy                       : Enabled
  Excessive ARP Activity                  : Enabled (per policy setting)

show wlan name client stats

To view the WLAN client statistics, use the show wlan name client stats command.

show wlan name wlan-name client stats

Syntax Description


`wlan-name`	WLAN name.

Command Default

None

Command Modes

Privileged EXEC(#)

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.1.1s	This command was introduced.

Examples

This example shows how to view the WLAN client statistics:

Device# show wlan name wlan1 client stats
 
Wlan Profile Name: wlan1, Wlan Id: 3
Current client state statistics:
-----------------------------------------------------------------------------
  Authenticating         : 0
  Mobility               : 0
  IP Learn               : 0
  Webauth Pending        : 0
  Run                    : 0

Locally Administered MAC Clients  : 0
L3 Access Clients                 : 0

.
.
.

show wlan summary sort ascending client-count

To view the WLAN summary sorted ascendingly based on the client count, use the show wlan summary sort ascending client-count command.

show wlan summary sort ascending client-count

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.1.1s	This command was introduced.

Examples

This example shows how to view the WLAN summary sorted ascendingly based on the client count:

Device# show wlan summary sort ascending client-count
---------------------------------------------------------------------------------------
Wlan-name                        ID            Client count           Data Usage
---------------------------------------------------------------------------------------
rlan_test_1                      1                1                     6277          
WLAN_CA_WPA2_AES_DOT1X           70               1                     167781

show wlan summary sort descending client-count

To view the WLAN summary sorted descendingly based on the client count, use the show wlan summary sort descending client-count command.

show wlan summary sort descending client-count

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.1.1s	This command was introduced.

Examples

This example shows how to view the WLAN summary sorted descendingly based on the client count:

Device# show wlan summary sort descending client-count
---------------------------------------------------------------------------------------
Wlan-name                        ID            Client count           Data Usage
---------------------------------------------------------------------------------------
rlan_test_1                      1                1                     6277          
WLAN_CA_WPA2_AES_DOT1X           70               1                     167781

show wlan summary sort ascending data-usage

To view the wlan summary sorted ascendingly based on the data usage, use the show wlan summary sort ascending data-usage command.

show wlan summary sort ascending data-usage

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Gibraltar 17.1.1	This command was introduced.

Examples

This example shows how to view the wlan summary sorted ascendingly based on the data usage:

Device# show wlan summary sort ascending data-usage
---------------------------------------------------------------------------------------
Wlan-name                        ID            Client count           Data Usage
---------------------------------------------------------------------------------------
rlan_test_1                      1                1                     6277          
WLAN_CA_WPA2_AES_DOT1X           70               1                     167781

show wlan summary sort descending data-usage

To view the WLAN summary sorted descendingly based on the data usage, use the show wlan summary sort descending data-usage command.

show wlan summary sort descending data-usage

Syntax Description


This command has no keywords or arguments.

Command Default

None

Command Modes

Privileged EXEC

Command History


Release	Modification
Cisco IOS XE Amsterdam 17.1.1s	This command was introduced.

Examples

This example shows how to view the WLAN summary sorted descendingly based on the data usage:

Device# show wlan summary sort descending data-usage
---------------------------------------------------------------------------------------
Wlan-name                        ID            Client count           Data Usage
---------------------------------------------------------------------------------------
WLAN_CA_WPA2_AES_DOT1X           70               1                     167781        
rlan_test_1                      1                1                     6277

show wps summary

To display Wireless Protection System (WPS) summary information, use the show wps summary command.

show wps summary

Syntax Description

This command has no arguments or keywords.

Command Default

None

Examples

The following example shows how to display WPS summary information:


(Cisco Controller) > show wps summary
Auto-Immune
  Auto-Immune.................................... Disabled
Client Exclusion Policy
  Excessive 802.11-association failures.......... Enabled
  Excessive 802.11-authentication failures....... Enabled
  Excessive 802.1x-authentication................ Enabled
  IP-theft....................................... Enabled
  Excessive Web authentication failure........... Enabled
Trusted AP Policy
  Management Frame Protection.................... Disabled
  Mis-configured AP Action....................... Alarm Only
    Enforced encryption policy................... none
    Enforced preamble policy..................... none
    Enforced radio type policy................... none
    Validate SSID................................ Disabled
  Alert if Trusted AP is missing................. Disabled
  Trusted AP timeout............................. 120
Untrusted AP Policy
  Rogue Location Discovery Protocol.............. Disabled
    RLDP Action.................................. Alarm Only
  Rogue APs
    Rogues AP advertising my SSID................ Alarm Only
    Detect and report Ad-Hoc Networks............ Enabled
  Rogue Clients
    Validate rogue clients against AAA........... Enabled
    Detect trusted clients on rogue APs.......... Alarm Only
  Rogue AP timeout............................... 1300
Signature Policy
  Signature Processing........................... Enabled
...

shutdown

To close the RF Profile and disable the network, use the shutdown command. To disable shutdown execution, use the no form of this command.

shutdown

Syntax Description


shutdown	Shuts down the profile and disables network.

Command Default

None

Command Modes

config-rf-profile

Command History


Release	Modification
Cisco IOS XE Denali 16.3.1	This command was introduced.

Usage Guidelines

None

Examples

This example shows how to close a RF Profile and disable the network.

Device(config-rf-profile)#shutdown

Bias-Free Language

Results

Chapter: Show Commands

Show Commands

show aaa dead-criteria radius

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

show aaa servers

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

show access-list

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

show ap name icap subscription ap rf spectrum

Syntax Description

Command Default

Command Modes

Command History

Examples

show ap airtime-fairness summary

Syntax Description

Command Default

Command Modes

Command History

Examples

show ap audit-report detail

Syntax Description

Command Default

Command Modes

Command History

Examples

show ap audit-report summary

Syntax Description

Command Default

Command Modes

Command History

Example

show ap auth-list

Syntax Description

Command Default

Command Modes

Command History

Examples

show ap auth-list ap-cert-policy

Syntax Description

Command Default

Command History

Examples

show ap auto-rf

Syntax Description

Command Default

Usage Guidelines

Examples

show ap ble cmx detail ip

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

show ap ble cmx summary

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples