Instructions for Addressing the Cisco Secure Boot Hardware Tampering Vulnerability on Cisco Catalyst 9800-80 Wireless Controller

This chapter provides instructions on how to address the Cisco Secure Boot Hardware Tampering Vulnerability on Cisco Catalyst 9800-80 Wireless Controller.


Note

Cisco recommends upgrading Field Programmable Gate Arrays (FPGA) as a solution for the Cisco Secure Boot Hardware Tampering Vulnerability. For more details of the vulnerability and affected products, refer https://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190513-secureboot.

Prerequisites for Upgrading FPGA

Download the image from the CCO website and copy it to USB or bootflash of the controller which is scheduled for the upgrade.


Note
Do not perform any power cycle or remove the power cable during the FPGA upgrade. If there is a power loss during the upgrade, it may result in corruption of the boot image and it may require RMA of the equipment.

Upgrading FPGA

To upgrade FPGA, run the upgrade utility image:

Procedure

Step 1

Copy the utility to USB or to bootflash: using FTP or TFTP.
Step 2

Save the current running configurations and backup it to bootflash.


WLC#copy running-config bootflash:running-config_15may2019                              
Destination filename [running-config_15may2019]?                                           
6222 bytes copied in 0.536 secs (11608 bytes/sec)                                          
WLC#  

WLC#write  memory
Building configuration...
[OK]
WLC#
Step 3

Note down the configuration register value and change it to 0x0.


WLC#sh ver | in Configuration
Configuration register is 0x2102
WLC#


WLC#configure terminal            
Enter configuration commands, one per line.  End with CNTL/Z.
WLC(config)#config-register 0x0                           
WLC(config)#end                                           
WLC#write
Step 4

Issue the controller reload command and ensure that the Rommon prompt is displayed on the controller.


WLC#reload                                                                                                                                      

System configuration has been modified. Save? [yes/no]: yes
Building configuration...                                  
[OK]
Step 5

Initiate the upgrade using the following CLI, and follow the instructions from the tool.

Note 

If the image is copied in USB, execute the following command:

boot usb0:C9800-80_fpga_prog.16.0.0.xe.bin

If the image is copied in Bootflash, execute the following command:

boot bootflash:C9800-80_fpga_prog.16.0.0.xe.bin
 

rommon 1 > boot usb0:C9800-80_fpga_prog.16.0.0.xe.bin
Located C9800-80_fpga_prog.16.0.0.xe.bin, start cluster is 786864
 
##############################################################################################################################################################################################################################
Image loaded
Boot image size = 22689808 (0x15a3810) bytes
 
ROM:RSA Self Test Passed
ROM:Sha512 Self Test Passed
 
Package header rev 1 structure detected
Calculating SHA-1 hash...done
validate_package_cs: SHA-1 hash:
                calculated 9b991366:34fd025f:987b920f:934aa266:fc2e0d08
                expected   9b991366:34fd025f:987b920f:934aa266:fc2e0d08
Validating main package signatures
 
RSA Signed RELEASE Image Signature Verification Successful.
Image validated
 
 
 
    Cisco ASR1K FPGA Programming Utility
 
  ****************************************
  **                                    **
  **    DO NOT TURN OFF THE POWER OR    **
  **  RESET THE BOX DURING THE UPGRADE  **
  **                                    **
  ****************************************

  Press 'Y' or 'y' to upgrade
  or any other key to reboot 

Detected Board Type: CE9800-80
 
SPI Flash Device ID: 0020ba17
 
Programming Flash ...
|.......|.......|.......|.......|.......|.......|.......|.......|
################################################################
Verifying Flash ...
|.......|.......|.......|.......|.......|.......|.......|.......|
################################################################
FPGA image verified correctly !!                                 

Router Power Cycle is needed for the changes to take effect
 
Press a key to Power cycle ...
 
Power cycling the box ...
 
 
    R˛
 
Initializing Hardware ...
 
System integrity status: 90170200 12030106 
 
 
System Bootstrap, Version 16.10(3r), RELEASE SOFTWARE
Copyright (c) 1994-2018  by cisco Systems, Inc.

Current image running: Boot ROM0
Last reset cause: PowerOn

C9800-80-K9 platform with 67108864 Kbytes of main memory
Important 
********************************

The following message confirms the upgrade is successful:

FPGA image verified correctly !!

In this case, skip Step 6 and Step 7, and proceed to Step 8 for verification.

Step 6

If the Upgrade is not successful, the following message appears: FPGA image failed to verify correctly !!

Retry the upgrade by issuing Yes. 


Use can issue “y” or “Y” to retry.

Detected Board Type: CE9800-80
SPI Flash Device ID: 00202015

Programming Flash ...
|.......|.......|.......|.......|.......|.......|.......|.......|
################################################################
Verifying Flash ...
|.......|.......|.......|.......|.......|.......|.......|.......|
FPGA image failed to verify correctly !!

Upgrade failed. Retrying ... 

       Cisco ASR1K FPGA Programming Utility

  ****************************************
  **                                    **
  **    DO NOT TURN OFF THE POWER OR    **
  **  RESET THE BOX DURING THE UPGRADE  **
  **                                    **
  ****************************************

  Press 'Y' or 'y' to upgrade
  or any other key to reboot

Detected Board Type: CE9800-80

SPI Flash Device ID: 0020ba17

Programming Flash ...
|.......|.......|.......|.......|.......|.......|.......|.......|
################################################################
Verifying Flash ...
|.......|.......|.......|.......|.......|.......|.......|.......|
################################################################
FPGA image verified correctly !!

Router Power Cycle is needed for the changes to take effect

Press a key to Power cycle ... 

Power cycling the box ... 

R˛
 
Initializing Hardware ...
 
System integrity status: 90170200 12030106

U

System Bootstrap, Version 16.10(3r), RELEASE SOFTWARE
Copyright (c) 1994-2018  by cisco Systems, Inc.

Current image running: Boot ROM0

Last reset cause: CPU-ResetRequest


rommon 1 >
Step 7

After the retry, if the upgrade still fails, reach out to Cisco TAC for further assistance.
Step 8

Once the upgrade is complete, device power cycles automatically, and the Rommon prompt is displayed to boot the IOS image.


Sample IOS boot steps are:

rommon 1 > dir bootflash:
File System: EXT2/EXT3   

15         526240224 -rw-r--r--     C9800-universalk9_wlc.2019-04-25_13.46_vgothe.SSA.bin

rommon 2 > boot bootflash: C9800-universalk9_wlc.2019-04-25_13.46_vgothe.SSA.bin
Step 9

Revert back the configuration register value to its original value.


WLC#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
WLC(config)#config-register 0x2102
WLC(config)#end
WLC#write

Verifying FPGA Upgrade

To verify the FPGA upgrade, use the following command:

WLC# show hw-programmable 0
Hw-programmable versions

Slot              CPLD version              FPGA version
-----------------------------------------------------------
0                 19030712                   N/A