Step 1

Choose Configuration > Tags & Profiles > Policy.

Step 2

On the Policy Profile page, click Add.

Step 3

In the Add Policy Profile window, in General tab, enter a name and description for the policy profile. The name can be ASCII characters from 32 to 126, without leading and trailing spaces. Do not use spaces as it causes system instability.

Step 4

To enable the policy profile, set Status as Enabled.

Step 5

In the WLAN Switching Policy section, choose the following, as required:

Step 6

Click Save & Apply to Device.

Step 1

Choose Configuration > Tags & Profiles > AP Join.

Step 2

On the AP Join Profile page, click Add.

Step 3

In the General tab, enter a name and description for the AP join profile.

Step 4

Check the LED State check box to set the LED state of all APs connected to the device to blink so that the APs are easily located.

Step 5

In the Client tab and Statistics Timer section, enter the time in seconds that the AP sends its 802.11 statistics to the controller.

Step 6

In the TCP MSS Configuration section, check the Adjust MSS Enable check box to enter value for Adjust MSS. You can enter or update the maximum segment size (MSS) for transient packets that traverse a router. TCP MSS adjustment enables the configuration of the maximum segment size (MSS) for transient packets that traverse a router, specifically TCP segments with the SYN bit set.

Step 7

In the AP tab, you can configure the following:

1. In the General tab, check the Switch Flag check box to enable switches.

2. Check the Power Injector State check box if power injector is being used. Power Injector increases wireless LAN deployment flexibility of APs by providing an alternative powering option to local power, inline power-capable multiport switches, and multiport power patch panels.

3. From the Power Injector Type drop-down list, choose power injector type from the following options:

   • Installed: If you want the AP to examine and remember the MAC address of the currently connected switch port. (This selection assumes that a power injector is connected.)

   • Override: To enable the AP to operate in high-power mode without first verifying a matching MAC address.

4. In the Injector Switch MAC field, enter the MAC address of the switch.

5. From the EAP Type drop-down list, choose the EAP type as EAP-FAST, EAP-TLS, or EAP-PEAP.

6. From the AP Authorization Type drop-down list, choose the type as either CAPWAP DTLS + or CAPWAP DTLS.

7. In the Client Statistics Reporting Interval section, enter the interval for 5 GHz and 2.4 GHz radios in seconds.

8. Check the Enable check box to enable extended module.

9. From the Profile Name drop-down list, choose a profile name.

10. Click Save & Apply to Device.

1. In the Hyperlocation tab, check the Enable Hyperlocation check box.

2. Enter the Detection Threshold value to filter out packets with low RSSI. The valid range is –100 dBm to –50 dBm.

3. Enter the Trigger Threshold value to set the number of scan cycles before sending a BAR to clients. The valid range is 0 to 99.

4. Enter the Reset Threshold value to reset value in scan cycles after trigger. The valid range is 0 to 99.

5. Enter the NTP Server IP address.

6. Click Save & Apply to Device.

1. In the BLE tab, enter a value in the Beacon Interval field to indicate how often you want your APs to send out beacon advertisements to nearby devices. The range is from 1 to 10, with a default of 1.

2. In the Advertised Attenuation Level field, enter the attenuation level. The range is from 40 to 100, with a default of 59.

3. Click Save & Apply to Device.

Step 8

In the Management tab, you can configure the following:

1. In the Device tab, enter the IPv4/IPv6 Address of the TFTP server, TFTP Downgrade section.

2. In the Image File Name field, enter the name of the software image file.

3. From the Facility Value drop-down list, choose the appropriate facility.

4. Enter the IPv4 or IPv6 address of the host.

5. Choose the appropriate Log Trap Value.

6. Enable Telnet and/or SSH configuration, if required.

7. Enable core dump, if required.

8. Click Save & Apply to Device.

1. In the User tab, enter username and password details.

2. Choose the appropriate password type.

3. In the Secret field, enter a custom secret code.

4. Choose the appropriate secret type.

5. Choose the appropriate encryption type.

6. Click Save & Apply to Device.

1. In the Credentials tab, enter local username and password details.

2. Choose the appropriate local password type.

3. Enter 802.1x username and password details.

4. Choose the appropriate 802.1x password type.

5. Enter the time in seconds after which the session should expire.

6. Enable local credentials and/or 802.1x credentials as required.

7. Click Save & Apply to Device.

1. In the CDP Interface tab, enable the CDP state, if required.

2. Click Save & Apply to Device.

Step 9

In the Rogue AP tab, check the Rogue Detection check box to enable rogue detection.

Step 10

In the Rogue Detection Minimum RSSI field, enter the RSSI value.

Step 11

In the Rogue Detection Transient Interval field, enter the transient interval value.

Step 12

In the Rogue Detection Report Interval field, enter the report interval value.

Step 13

Check the Rogue Containment Automatic Rate Selection check box to enable rogue containment automatic rate selection.

Step 14

Check the Auto Containment on FlexConnect Standalone check box to enable the feature.

Step 15

Click Save & Apply to Device.

Step 1

Choose Configuration > Tags & Profiles > RF.

Step 2

On the RF Profile page, click Add.

Step 3

In the General tab, enter a name for the RF profile. The name can be ASCII characters from 32 to 126, without leading and trailing spaces.

Step 4

Choose the appropriate Radio Band.

Step 5

To enable the profile, set the status as Enable.

Step 6

Enter a Description for the RF profile.

Step 7

Click Save & Apply to Device.

Step 1

Choose Configuration > Tags & Profiles > Tags > Policy.

Step 2

Click Add to view the Add Policy Tag window.

Step 3

Enter a name and description for the policy tag. The name can be ASCII characters from 32 to 126, without leading and trailing spaces.

Step 4

Click Add to map WLAN and policy.

Step 5

Choose the WLAN profile to map with the appropriate policy profile, and click the tick icon.

Step 6

Click Save & Apply to Device.

Step 1

1. Choose Configuration > Tags & Profiles > Tags > RF.

Step 2

Click Add to view the Add RF Tag window.

Step 3

Enter a name and description for the RF tag. The name can be ASCII characters from 32 to 126, without leading and trailing spaces.

Step 4

Choose the required 5 GHz Band RF Profile and 2.4 GHz Band RF Profile to be associated with the RF tag.

Step 5

Click Update & Apply to Device.

Step 1

Choose Configuration > Wireless > Access Points.

Step 2

To edit the configuration details of an AP, select the row for that AP.

Step 3

In the General tab and Tags section, specify the appropriate policy, site, and RF tags, that you created on the Configuration > Tags & Profiles > Tags page.

Step 4

Click Update & Apply to Device.

Step 1

Choose Configuration > Tags & Profiles > Tags > AP > Tag Source.

Step 2

Drag and Drop the Tag Sources to change priorities.

Step 1

Choose Configuration > Tags & Profiles > Tags > AP > Filter.

Step 2

Click Add.

Step 3

In the Associate Tags to AP dialog box which is displayed, enter the Rule Name, the AP name regex and the Priority. Optionally, you can also choose the policy tag from the Policy Tag Name drop-down list, the site tag from the Site Tag Name drop-down list and the RF tag from the RF Tag Name drop-down list.

Step 4

Click Apply to Device.

Step 1

Choose Configuration > Tags & Profiles > Tags > AP > Filter.

Step 2

1. If you want to setup a new AP filter, then click Add. In the Associate Tags to AP dialog box which is displayed, enter the Rule Name, the AP name regex and the Priority. Optionally, you can also select the Policy Tag Name, the Site Tag Name and the RF Tag Name. Click Apply to Device.

2. If you want to update the priority of an existing AP filter, click on the Filter and in the Edit Tags dialog box and change the Priority. In case the Filter is Inactive, no priority can be set to it. Click Update and Apply to Device.

Step 1

Choose Configuration > Wireless Setup > Basic.

Step 2

On the Basic Wireless Setup page, click Add.

Step 3

In the General tab, enter a name and description for the location.

Step 4

Set the Location Type as either Local or Flex.

Step 5

Use the slider to set Client Density as Low, Typical or High.

Step 6

Click Apply.

Step 1

Choose Configuration > Wireless Setup > Basic.

Step 2

On theBasic Wireless Setup page, click Add to configure the following:

Step 3

In the AP Provisioning tab and Add/Select APs section, enter the AP MAC address and click the right arrow to add the AP to the associated list.

Step 4

Use the search option in the Available AP List to select the APs from the Selected AP list and click the right arrow to add the AP to the associated list.

Step 5

Click Apply.