Mise à niveau de CPLD sur la configuration SVL Catalyst 9400
Introduction
Ce document décrit une procédure étape par étape sur la façon de mettre à niveau la version CPLD (Complex Programmable Logic Device) sur une configuration de liaison virtuelle StackWise (SVL) de Catalyst 9400.
Conditions préalables
Exigences
Cisco recommande que vous ayez des connaissances de base sur la configuration et la configuration de Stackwise-Virtual sur le Catalyst 9400.
Composants utilisés
Les informations dans ce document sont basées sur le PID : C9404R versions du logiciel et du matériel.
Modules:
C940-SUP-1XL
C940-LC-24XS
Version du logiciel : 17.09.4a
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. Si votre réseau est en ligne, assurez-vous de bien comprendre l’incidence possible des commandes.
Topologie
Problème
Dans Catalyst 9400, lors de la mise à niveau de la version Cisco IOS®, dans de rares cas, la version CPLD du périphérique n'est pas mise à niveau. La version CPLD et la version Rommon pour la version particulière peut être vérifiée à partir du lien https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9400/software/release/17-13/release_notes/ol-17-13-9400/rommon_versions.html.
Référez-vous à cet extrait de code :
9400-1#show platform
Chassis type: C9404R
Switch 1
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
1 C9400-LC-24XS ok 00:05:00
1/0 C9400-LC-24XS ok 00:00:56
2 C9400-SUP-1XL ok 00:05:00
2/0 C9400-SUP-1XL ok 00:00:53
R0 ok, active 00:05:00
P1 C9400-PWR-3200AC ok 00:04:38
P9 C9404-FAN ok 00:04:37
Slot CPLD Version Firmware Version
--------- ------------------- ---------------------------------------
1 20062105 17.10.1r
2 20062105 17.10.1r
Switch 2
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
1 C9400-LC-24XS ok 00:04:57
1/0 C9400-LC-24XS ok 00:00:08
2 C9400-SUP-1XL ok 00:04:57
2/0 C9400-SUP-1XL ok 00:00:07
R0 ok, standby 00:04:57
P1 C9400-PWR-3200AC ok 00:04:35
P9 C9404-FAN ok 00:04:33
Slot CPLD Version Firmware Version
--------- ------------------- ---------------------------------------
1 19032905 17.10.1r >>>>>>>>>>CPLD did not get upgraded
2 19032905 17.10.1r >>>>>>>>>>CPLD did not get upgraded
Dans ce cas, le CPLD du standby n'a pas été mis à niveau après la mise à niveau.
Procédure De Mise À Niveau
Étape 1. Utilisez la show redundacny afin de vérifier si le SVL fonctionne correctement.
9400-1#show redundancy
Redundant System Information :
------------------------------
Available system uptime = 4 minutes
Switchovers system experienced = 0
Standby failures = 0
Last switchover reason = none
Hardware Mode = Duplex
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
Maintenance Mode = Disabled
Communications = Up
Current Processor Information :
-------------------------------
Active Location = Switch 1
Current Software state = ACTIVE
Uptime in current state = 4 minutes
Image Version = Cisco IOS Software [Cupertino], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 17.9.4a, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2023 by Cisco Systems, Inc.
Compiled Fri 20-Oct-23 10:44 by mcpre
BOOT = bootflash:packages.conf;
Peer Processor Information :
----------------------------
Standby Location = Switch 2 >>>>>>>>>>Switch 2 is standby
Current Software state = STANDBY HOT
Uptime in current state = 0 minutes
Image Version = Cisco IOS Software [Cupertino], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 17.9.4a, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2023 by Cisco Systems, Inc.
Compiled Fri 20-Oct-23 10:44 by mcpre
BOOT = bootflash:packages.conf;Étape 2. Afin de mettre à niveau la version CPLD utilisez cette commande :
upgrade hw-programmable cpld filename bootflash: switch {1-2} RP active9400-1#upgrade hw-programmable cpld filename bootflash: switch 2 R0
Firmware upgrade requires the SVL member to reload. Do you want to proceed?(y/n)y
Use cli 'redundancy reload peer' to upgrade the firmware on peer
9400-1#redundancy reload peer
Stack is in Half ring setup; Reloading a switch might cause stack split
Reload peer [confirm]
Preparing to reload peerÉtape 3. Ici, vous pouvez voir que le CPLD est en cours de mise à niveau :
Chassis 2 reloading, reason - Admin reload CLI
May 4 01:34:23.829: %PMAN-5-EXITACTION: R0/0: pvp:
Initializing Hardware......
System Bootstrap, Version 17.10.1r, RELEASE SOFTWARE (P)
Compiled Tue Aug 2 13:02:51 2022 by rel
Current ROMMON image : Primary
Last reset cause : SoftwareResetTrig
C9400-SUP-1XL platform with 16777216 Kbytes of main memory
Starting System FPGA Upgrade .....
Programming SPI Primary image is completed.
Authenticating SPI Primary image .....
IO FPGA image is authenticated successfully.
Programming Header .....
FPGA HDR file size: 12
Image page count: 1
Verifying programmed header .....
Verifying programmed header .....
Programmed header is verified successfully.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Power Cycle is needed to complete System firmware upgrade.
It takes ~7 mins to upgrade firmwre after power cycle starts.
DO NOT DISRUPT AFTER POWER C
Initializing Hardware......
Initializing Hardware......
System Bootstrap, Version 17.10.1r, RELEASE SOFTWARE (P)
Compiled Tue Aug 2 13:02:51 2022 by relÉtape 4. Vérifiez si le CPLD est mis à niveau en veille :
F241.24.02-9400-1#show platform
Chassis type: C9404R
Switch 1
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
1 C9400-LC-24XS ok 00:29:38
1/0 C9400-LC-24XS ok 00:25:34
2 C9400-SUP-1XL ok 00:29:38
2/0 C9400-SUP-1XL ok 00:25:31
R0 ok, active 00:29:38
P1 C9400-PWR-3200AC ok 00:29:16
P9 C9404-FAN ok 00:29:14
Slot CPLD Version Firmware Version
--------- ------------------- ---------------------------------------
1 20062105 17.10.1r
2 20062105 17.10.1r
Switch 2
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
1 C9400-LC-24XS ok 00:29:35
1/0 C9400-LC-24XS ok 00:00:11
2 C9400-SUP-1XL ok 00:29:35
2/0 C9400-SUP-1XL ok 00:00:10
R0 ok, standby 00:29:35
P1 C9400-PWR-3200AC ok 00:29:13
P9 C9404-FAN ok 00:29:11
Slot CPLD Version Firmware Version
--------- ------------------- ---------------------------------------
1 20062105 17.10.1r >>>>>>>>>>CPLD got upgraded
2 20062105 17.10.1r >>>>>>>>>>CPLD got upgraded
Étape 5. Dans ce cas, si la version CPLD du commutateur actif doit être mise à niveau, vous devez procéder comme suit :
1. Do a switchover
9400-1#redundency force-switchover >>>>>>>>>>Initially Switch 1 is active and Switch 2 is standby.
After switchover it is vise-versa
2. Upgrade the CPLD version of previous active [now standby] with the command:
9400-1#upgrade hw-programmable cpld filename bootflash: switch 1 R0
3. Reload the the standby
9400-1#redundancy reload peer
Historique de révision
| Révision | Date de publication | Commentaires |
|---|---|---|
1.0 |
22-May-2024 |
Première publication |
Commentaires