例
次に、802.3bt 対応のインターフェイスの PoE ステータスを表示するコマンドの例を示します。
Device# show power inline upoe-plus gigabitEthernet 1/0/23
Codes: DS - Dual Signature device, SS - Single Signature device
SP - Single Pairset device
Interface Admin Type Oper-State Power(Watts) Class Device Name
State Alt-A,B Allocated Utilized Alt-A,B
----------- ------ ---- ---------- --------- --------- ------- -----------
Gi1/0/4 auto SP on 4.0 3.8 1 Ieee PD
Gi1/0/15 auto SS on,on 60.0 10.5 6 Ieee PD
Gi1/0/23 auto DS on,on 45.4 26.9 3,4 Ieee PD
次に、show power inline upoe-plus コマンドの出力に表示されるフィールドについて説明します。
表 4. show power inline upoe-plus コマンドの出力に表示されるフィールド
フィールド
|
説明
|
Type
|
受電デバイスのタイプ:シングルペアセットデバイス(SP)、シングルシグネチャデバイス(SS)、デュアルシグネチャデバイス(DS)
|
Oper-State
|
ポート上の各ペアの状態
|
Power Allocated
|
ポートに割り当てられた電力
|
Power Utilized
|
ポート上の受電デバイスの消費電力
|
Class Alt-A, B
|
対応する信号ペアまたはスペアペア
|
Device Name
|
CDP によってアドバタイズされた受電デバイスの名前
|
show power inline detail コマンドは、デバイスの動作ステータス、デバイスの IEEE クラス、物理的に割り当てられたクラス、割り当てられた電力、ポートで測定された(電力)などの 802.3bt 準拠デバイスの情報を表示するように拡張されました。
クラス 5 シングルシグニチャ受電デバイスが LLDP を介して要求を送信し、PSE によって割り当てられた電力を低減する(このため、割り当てられた電力が 30 W に低下)シナリオを検討します。次に、このようなシナリオでの show power inline detail コマンドの出力を示します。
Device# show power inline gigabitEthernet 1/0/29 detail
Interface: Gi1/0/29
Inline Power Mode: auto
Operational status (Alt-A,B): on,on
Device Detected: yes
Device Type: Ieee PD
Connection Check: SS
IEEE Class (Alt-A,B): 5
Physical Assigned Class (Alt-A,B): 5
Discovery mechanism used/configured: Ieee and Cisco
Police: off
Power Allocated
Admin Value: 60.0
Power drawn from the source: 30.0
Power available to the device: 30.0
Allocated Power (Alt-A,B): 30.0
Actual consumption
Measured at the port(watts) (Alt-A,B): 10.5
Maximum Power drawn by the device since powered on: 10.5
Absent Counter: 0
Over Current Counter: 0
Short Current Counter: 0
Invalid Signature Counter: 0
Power Denied Counter: 0
Power Negotiation Used: IEEE 802.3bt LLDP
LLDP Power Negotiation --Sent to PD-- --Rcvd from PD--
Power Type: Type 2 PSE Type 2 PD
Power Source: Primary PSE
Power Priority: low critical
PD 4PID: 0 1
Requested Power(W): 25.5 25.5
Allocated Power(W): 25.5 40.0
Requested Power ModeA(W): 0.0 6.5
Allocated Power ModeA(W): 0.0 25.5
Requested Power ModeB(W): 0.0 13.0
Allocated Power ModeB(W): 0.0 25.5
PSE Powering Status: 4 pair SS PD Ignore
PD Powering Status: Ignore SS PD
PSE Power Pair ext: Both Alternatives Both Alternatives
DS Class Mode A ext: SS PD Class 2
DS Class Mode B ext: SS PD Class 4
SS Class ext: Class 4 Class 5
PSE Type ext: Type 3 PSE Type 3 SS PD
PSE Max Avail Power: 51.0 51.2
PSE Auto Class Supp: No No
PD Auto Class Req: No No
PD Power Down Req: No No
PD Power Down Time(sec): 0 70
Four-Pair PoE Supported: Yes
Spare Pair Power Enabled: Yes
Four-Pair PD Architecture: Shared
次に、デュアルシグネチャ受電デバイスが PSE によって割り当てられた電力を低減する要求を送信する出力の例を示します。
Device#show power inline gigabitEthernet 1/0/23 detail
Interface: Gi1/0/23
Inline Power Mode: auto
Operational status (Alt-A,B): on,on
Device Detected: yes
Device Type: Ieee PD
Connection Check: DS
IEEE Class (Alt-A,B): 3,4
Physical Assigned Class (Alt-A,B): 3,4
Discovery mechanism used/configured: Ieee and Cisco
Police: off
Power Allocated
Admin Value: 60.0
Power drawn from the source: 22.4
Power available to the device: 22.4
Allocated Power (Alt-A,B): 7.0,15.4
Actual consumption
Measured at the port(watts) (Alt-A,B): 2.7,2.7
Maximum Power drawn by the device since powered on: 5.5
Absent Counter: 0
Over Current Counter: 0
Short Current Counter: 0
Invalid Signature Counter: 0
Power Denied Counter: 0
Power Negotiation Used: IEEE 802.3bt LLDP
LLDP Power Negotiation --Sent to PD-- --Rcvd from PD--
Power Type: Type 2 PSE Type 2 PD
Power Source: Primary PSE
Power Priority: low critical
PD 4PID: 0 1
Requested Power(W): 19.9 0.0
Allocated Power(W): 19.9 0.0
Requested Power ModeA(W): 6.5 6.5
Allocated Power ModeA(W): 6.5 13.0
Requested Power ModeB(W): 13.0 13.0
Allocated Power ModeB(W): 13.0 25.5
PSE Powering Status: 4 pair DS PD Ignore
PD Powering Status: Ignore 2 pair DS PD
PSE Power Pair ext: Both Alternatives Both Alternatives
DS Class Mode A ext: Class 2 Class 3
DS Class Mode B ext: Class 3 Class 4
SS Class ext: DS PD Class 5
PSE Type ext: Type 3 PSE Type 3 SS PD
PSE Max Avail Power: 51.0 51.2
PSE Auto Class Supp: No No
PD Auto Class Req: No No
PD Power Down Req: No No
PD Power Down Time(sec): 0 70
Four-Pair PoE Supported: Yes
Spare Pair Power Enabled: Yes
Four-Pair PD Architecture: Independent
次に、show power inline priority コマンドの出力例を示します。
Device# show power inline priority gigabitEthernet 1/0/1
Interface Admin Oper Admin Oper
State State Priority Priority
---------- ------ ---------- ---------- --------
Gi1/0/1 static on 5 7
Priority Power Per
Priority(Watts)
---------- --------------
0 0
1 1440
2 1440
3 2880
4 0
5 2880
6 0
7 0
Device# show power inline priority gigabitEthernet 1/0/45
Interface Admin Oper Admin Oper
State State Priority Priority
---------- ------ ---------- ---------- --------
Gi1/0/45 auto on 5 5
Priority Power Per
Priority(Watts)
---------- --------------
0 0
1 1440
2 1440
3 2880
4 0
5 2880
6 0
7 0
次に、show power inline priority コマンドの出力に表示されるフィールドについて説明します。
表 5. show power inline priority コマンドの出力に表示されるフィールド
フィールド
|
説明
|
Admin State
|
管理モード:auto、off、static
|
Oper State
|
動作モード:on、off、faulty、power-deny
|
Admin Priotity
|
管理優先順位レベル:0 〜 7
|
Oper Priotity
|
動作優先順位レベル:0 〜 7
|
Power Per Priority(Watts)
|
PoE ポートの優先順位に割り当てられる電力
|