概要
IP 設定、ホスト設定、および Network Time Protocol(NTP)設定を表示および変更するには、[設定(Settings)] オプションを使用します。
この製品のドキュメントセットは、偏向のない言語を使用するように配慮されています。このドキュメントセットでの偏向のない言語とは、年齢、障害、性別、人種的アイデンティティ、民族的アイデンティティ、性的指向、社会経済的地位、およびインターセクショナリティに基づく差別を意味しない言語として定義されています。製品ソフトウェアのユーザインターフェイスにハードコードされている言語、RFP のドキュメントに基づいて使用されている言語、または参照されているサードパーティ製品で使用されている言語によりドキュメントに例外が存在する場合があります。シスコのインクルーシブ ランゲージの取り組みの詳細は、こちらをご覧ください。
このドキュメントは、米国シスコ発行ドキュメントの参考和訳です。リンク情報につきましては、日本語版掲載時点で、英語版にアップデートがあり、リンク先のページが移動/変更されている場合がありますことをご了承ください。あくまでも参考和訳となりますので、正式な内容については米国サイトのドキュメントを参照ください。
IP 設定、ホスト設定、および Network Time Protocol(NTP)設定を表示および変更するには、[設定(Settings)] オプションを使用します。
[IP 設定(IP Settings)] オプションを使用すると、イーサネット接続の IP とポートの設定を表示および変更できます。また、後続のノードでは、パブリッシャの IP アドレスを設定できます。
[IP 設定(IP Settings)] ウィンドウには、Dynamic Host Configuration Protocol(DHCP)がアクティブかどうかが表示され、関連するイーサネット IP アドレスとネットワークゲートウェイの IP アドレスも表示されます。
すべてのイーサネット設定は、Eth0 にのみ適用されます。Eth1 の設定は構成できません。デフォルトでは、[最大転送単位(MTU)(Maximum transmission unit (MTU))] は 1,500 バイトに設定されます。
IP 設定を表示するには、次の手順を実行します。
注意 |
Cisco Unity Connection の IP 設定を変更する手順は使用しないでください。 |
注意 |
Connection サーバーの IP アドレスの変更については、https://www.cisco.com/c/ja_jp/support/unified-communications/unity-connection/products-installation-guides-list.html にある『Changing the IP Addresses of Cisco Unity Connection Servers』『Unity Connection アップグレードガイド』の「Cisco Unity Connection Servers の IP アドレスを変更する」を参照してください。 |
注意 |
Unity Connection サーバーのホスト名の変更については、https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/connection/15/install_upgrade/guide/b_15cuciumg.html にある 『Cisco Unity Connection インストール、アップグレード、およびメンテナンスガイド 15』を参照してください。 |
[Cisco Unified Communications Operating System Administration] ウィンドウから に移動します。[イーサネット設定(Ethernet Settings)] ウィンドウが表示されます。[イーサネット設定(Ethernet Settings)] ウィンドウのフィールドの説明については、 表 4-1を参照してください。
|
(注) |
次に示す設定は、Cisco Unity Connection リリース 9.0 以降に適用されます。IPv6 は、以前のバージョンの Cisco Unity Connection ではサポートされていません。 |
[イーサネット IPv6 構成設定(Ethernet IPv6 Configuration Settings)] ページでは、IPv6 を有効にし、IP アドレスの取得方法を決定できます。
IPv6 設定を表示または変更するには、次の手順を実行します。
ステップ 1 |
[Cisco Unified Communications Operating System Administration] ウィンドウから に移動します。 |
||||||||||||||||
ステップ 2 |
イーサネット IPv6 設定を変更するには、該当するフィールドに新しい値を入力します。[イーサネット IPv6 構成設定(Ethernet IPv6 Configuration Settings)] ウィンドウのフィールドの説明については、 表 4-2を参照してください。 |
||||||||||||||||
ステップ 3 |
変更を保存するには、[保存(Save)] を選択します。
|
この機能は、Cisco Unified Communications Manager がサーバーに単独でインストールされている場合にのみ適用されます。
外部 NTP サーバーがストラタム 9 以上(1 ~ 9)であることを確認します。外部 NTP サーバーを追加、削除、または変更するには、次の手順を実行します。
(注) |
NTP サーバー設定は、最初のノードまたはパブリッシャでのみ設定できます。 |
ステップ 1 |
[Cisco Unified Communications Operating System Administration] ウィンドウから に移動します。[NTP サーバー設定(NTP Server Settings)] ウィンドウが表示されます。 |
||
ステップ 2 |
NTP サーバーを追加、削除、または変更できます。
|
||
ステップ 3 |
[NTP サーバー設定(NTP Server Settings)] ウィンドウを更新して正しいステータスを表示するには、 を選択します。
|
[SMTP 設定(SMTP Settings)] ウィンドウでは、SMTP ホスト名を表示または設定し、SMTP ホストがアクティブかどうかを示すことができます。
ヒント |
システムから電子メールが送信されるようにするには、SMTP ホストを設定する必要があります。 |
SMTP 設定にアクセスするには、次の手順を実行します。
ステップ 1 |
[Cisco Unified Communications Operating System Administration] ウィンドウから に移動します。[SMTP 設定(SMTP Settings)] ウィンドウが表示されます。 |
ステップ 2 |
ホスト名または IP アドレスを入力します。 |
ステップ 3 |
[保存(Save)] をクリックします。 |
手動で時間を設定するには、以下の手順に従います。
(注) |
サーバーの時刻を手動で設定する前に、設定した NTP サーバーを削除する必要があります。詳細については、 「NTP サーバー」(4-3 ページ)の項を参照してください。 |
ステップ 1 |
[Cisco Unified Communications Operating System Administration] ウィンドウから に移動します。 |
ステップ 2 |
システムの日付と時刻を入力します。 |
ステップ 3 |
[保存(Save)] をクリックします。 |
ステップ 4 |
Cisco Unity Connection サーバーで、日付を変更した場合、または時刻を 2 分以上変更した場合は、CLI コマンド utils system restart を使用してサーバーを再起動します。 |