在MS-DOS平台装载Aironet驱动程序

简介

本文档介绍如何在基于Microsoft DOS (MS-DOS)的笔记本电脑上安装Cisco Aironet驱动程序。

先决条件

要求

Cisco 建议您了解以下主题：

• 无线LAN (WLAN)技术和术语

• PC硬件主题

• MS-DOS配置命令

使用的组件

本文档中的信息基于以下软件和硬件版本：

• Aironet PCM 3xx或LMC 3xx客户端适配器

• MS-DOS 6.22

• 用于DOS的Aironet驱动程序6.22版

规则

有关文档规则的详细信息，请参阅 Cisco 技术提示规则。

安装适用于Aironet的DOS驱动程序

要安装DOS驱动程序，请完成以下步骤：

1. 用以下方法生成config.sys文件：

   DEVICE=A:\DOS\HIMEM.SYS
   DEVICE=A:\DOS\EMM386.EXE X=D000-DFFF FRAME=NONE
   DEVICEHIGH=A:\IBMDSS14.SYS
   DEVICEHIGH=A:\IBMDOSCS.SYS
   DEVICEHIGH=A:\DICRMU01.SYS /MA-D000-D7FF /SH=1 /IX=5,10,11,15
   DEVICE=A:\NET\IFSHLP.SYS
   DEVICE=A:\DOS\RAMDRIVE.SYS 2048 /e
   DEVICE=A:\DOS\ANSI.SYS
   DOS=HIGH,UMB
   FILES=40
   BUFFERS=30
   LASTDRIVE=Z
   SHELL=COMMAND.COM /e:512 /p

   IBMDSS14.SYS、IBMDOSCS.SYS和DICRMU01.SYS文件是用于示例型号IBM笔记本电脑的PCMCIA卡和套接字服务。根据情况替换笔记本电脑制造商提供的适当文件。

2. 根据个人需要自定义随附的cscpkt.ini文件：

   [CSCPKT]
           ;Initialization file for Infrastructure operating mode
   
           ; NOTE: The following are some keyword parameters that may
           ;be modified.  Any commented or omitted keyword parameter
           ;assumes the factory default.  For most situations the
           ;factory defaults will be appropriate.  In situations where
           ;the factory default needs to be modified, uncomment or add the
           ;keyword parameter line and set the appropriate keyword value.
   
           SSID="network_ssid"     ;Must match Access Point setting
           ;FragThreshold=2312     ;Packet size to start fragmenting
           ;RTSThreshold=2312      ;Packet size to start sending RTS/CTS
           ;DataRate1=0x02         ;(1)   Mbps supported data bit rate
           ;DataRate2=0x04         ;(2)   Mbps supported data bit rate
           ;DataRate3=0x0B         ;(5.5) Mbps supported data bit rate
           ;DataRate4=0x16         ;(11)  Mbps supported data bit rate
           ;RefreshInterval=10000  ;Inactivity time to check association
           ;PowerSaveMode="CAM"    ;Constant Awake Mode
           ;MaxPowerSave="OFF"     ;Maximum power save mode
           NodeName="CiscoPC"      ;Descriptive station name
           AuthType="WEPOPEN"      ;WEP with open authentication
   
           ;The adapter needs 32 16-bit I/O ports, and 1 non-sharable IRQ.
           ;The following lines should be uncommented and the appropriate
           ;values set in the following scenarios:
           ; 1) PCMCIA mode: Override the I/O port base and/or IRQ
           ;                 assigned by PCMCIA card services.
           ; 2) PCMCIA mode: PCMCIA card services is not being used.
           ; 3) ISA mode: Override the I/O port base and/or IRQ assigned
           ;              by Plug and Play.
           ; 4) ISA mode: Non-Plug and Play operation.
           
           ;PortBase=0x140
           ;IRQ=5
   
           ;If the PCMCIA interface is being used without PCMCIA card services,
           ;uncomment the following lines and set the appropriate values.
   
           Memory=0xD000
           Socket=0
   
           ;If the PCMCIA interface is not being used, set the appropriate
           ;value of "ISA" or "PCI".
   
           BusType="PCMCIA"

3. 启动计算机以加载上述config.sys文件。

4. 发出以下命令：

   a:>wepdos -365 -tx1 12345678901234567890123456
   

   setting key 1 to 12345678901234567890123456
   setting transmit key index to 1

5. 发出以下命令：

   a:>cscpkt 0x65
   

   Cisco Wireless Packet Driver , version 2.04
   (c) Copyright 2000 Cisco System , Inc.
   All rights Reserved
   Card recognized as a radio in socket 00
   Driver Resources --> IO ports 0400-043F IRQ :03
   350 series Firmware 4.25.30
   Mac Address 00:09:7c:31:87:32
   

相关信息

• Cisco Aironet无线局域网客户端适配器配置指南
• 思科无线产品
• Cisco Aironet Windows 客户端常见问题
• 技术支持和文档 - Cisco Systems