Inbound Leg Headers for Outbound Dial-Peer Matching

The Inbound Leg Headers for Outbound Dial-Peer Matching feature allows you to match and provision an outbound dial peer for an outbound call leg using the headers from an inbound call leg. The following headers of an incoming call leg can be used for outbound dial-peer matching:

  • VIA (SIP Header)

  • FROM (SIP Header)

  • TO (SIP Header)

  • DIVERSION (SIP Header)

  • REFERRED BY (SIP Header)

  • Called Number

  • Calling Number

  • Carrier ID

Feature Information for Inbound Leg Headers for Outbound Dial-Peer Matching

The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
Table 1. Feature Information for Inbound Leg Headers for Outbound Dial-Peer Matching

Feature Name

Releases

Feature Information

Inbound Leg Headers for Outbound Dial-Peer Matching

15.4(2)T, Cisco IOS XE Release 3.12S

TheInbound Leg Headers for Outbound Dial-Peer Matching feature allows you to match and provision an outbound call leg using the headers of an inbound call leg.

The following commands were introduced by this feature: destination provision-policy , destination uri-via , destination uri-to , destination uri-from , destination uri-diversion , destination uri-referred-by , show voice class dial-peer provision-policy

The following commands were modified.

show command incall , show dialplan dialpeer .

Prerequisites for Inbound Leg Headers for Outbound Dial-Peer Matching

  • CUBE or Voice Gateway must be configured.

Restrictions for Inbound Leg Headers for Outbound Dial-Peer Matching

  • The existing header-passing command supports modification of SIP headers of INVITE message by the Tool Command Language (TCL) application. If the above SIP headers are modified by the TCL application, they cannot be used for outbound dial-peer provisioning.

  • If multiple SIP via headers and diversion headers are found in an incoming INVITE or REFER message, only the top-most via header and top-most diversion header of an incoming INVITE or REFER message are used for outbound dial-peer provisioning.

  • When an incoming call is matched to an inbound dial peer with an associated provision profile without rules, outbound dial-peer provisioning is disabled and the incoming call is disconnected by CUBE or voice gateway with cause code "unassigned number (1)".

Information About Inbound Leg Headers for Outbound Dial-Peer Matching

This feature allows you to match headers of an inbound call leg and provision an outbound dial peer for an outbound call leg. The following SIP headers of an incoming call leg can be used for outbound dial-peer matching

  • VIA (SIP Header)
  • FROM (SIP Header)
  • TO (SIP Header)
  • DIVERSION (SIP Header)
  • REFERRED BY (SIP Header)
  • Called Number
  • Calling Number
  • Carrier ID

The above headers are retrieved from an incoming INVITE or REFER message and used for outbound dial-peer provisioning.

SIP headers of an INVITE message are saved to an associated call leg. For example, an INVITE message is received for a new call leg A. Then, SIP headers are saved to call leg A itself for outbound dial-peer lookup.

On the other hand, SIP headers of a REFER message are saved to the peer call leg of the associated call leg. For example, call leg A and call leg B are connected in CUBE. The party at Call Leg B makes a blind transfer to the party at Call Leg C. A REFER message is received in CUBE for call leg B (transferor). But, SIP headers of the REFER message are saved under call leg A (transferee) for an outbound dial-peer lookup for Party C.

Configuring Inbound Leg Headers for Outbound Dial-Peer Matching

Before you begin

Necessary pattern maps have been configured.

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. voice class dial-peer provision-policy tag
  4. (Optional) description string
  5. preference preference-order first-attribute second-attribute
  6. exit
  7. dial-peer voice inbound-dial-peer-tag voip
  8. destination provision-policy tag
  9. exit
  10. dial-peer voice outbound-dial-peer-tag voip
  11. Configure a match command for an outbound dial peer according to the provision policy rule attribute configured.
  12. end

DETAILED STEPS

  Command or Action Purpose
Step 1

enable

Example:


Device> enable

Enters privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

Example:


Device# configure terminal

Enters global configuration mode.

Step 3

voice class dial-peer provision-policy tag

Example:

Device(config)# voice class dial-peer provision-policy 200

Creates a provision policy profile in which a set of attributes for dial-peer matching can be defined.

  • You can use the shutdown command to deactivate the provision policy and allow normal outbound dial-peer provisioning.
Step 4

(Optional) description string

Example:


Device(voice-class)# description match both calling and called
(Optional)

Provides a description for the provision policy profile.

Step 5

preference preference-order first-attribute second-attribute

First Attribute Second Attribute
diversion from, referred-by, to, uri, via
from diversion, referred-by, to, uri, via
referred-by diversion, from, to, uri, via
to diversion, referred-by, from, uri, via
uri diversion, referred-by, to, from, via, carrier-id
via diversion, referred-by, to, uri, from
called calling, carrier-id
calling called
carrier-id called, uri

Example:


Device(voice-class)# preference 2 calling called

Configures a provision policy rule.

  • You can configure up to two rules. This means up to four attributes can be configured for matching outbound dial peers.
  • If rules are not configured, outbound dial-peer provisioning is disabled, and an incoming call matched to an inbound dial peer associated with this profile is disconnected by CUBE or voice gateway with cause code "unassigned number (1)".
Step 6

exit

Example:


Device(voice-class)# exit

Exits voice class configuration mode and enters global configuration mode.

Step 7

dial-peer voice inbound-dial-peer-tag voip

Enters dial peer configuration mode for an inbound dial peer.
Step 8

destination provision-policy tag

Example:

Device(config)# dial-peer voice 100 voip
Device(config-dial-peer)# destination provision-policy 200
Device(config)# exit

Associates a provision policy profile with an inbound dial peer.

Step 9

exit

Exits dial peer configuration mode.
Step 10

dial-peer voice outbound-dial-peer-tag voip

Enters dial peer configuration mode for an outbound dial peer.
Step 11

Configure a match command for an outbound dial peer according to the provision policy rule attribute configured.

Provision Policy Rule Attribute Dial-peer Match command
called

destination-pattern pattern

destination e164-pattern-map pattern-map-class-id

calling

destination calling e164-pattern-map pattern-map-class-id

carrier-id

carrier-id target

uri

destination uri uri-class-tag

via

destination uri-via uri-class-tag

to

destination uri-to uri-class-tag

from

destination uri-from uri-class-tag

diversion

destination uri-diversion uri-class-tag

referred-by

destination uri-referred-by uri-class-tag

Example:

Device(config)# dial-peer voice 300 voip
Device(config-dial-peer)# destination uri-from 200
Device(config)# exit
Configure a match command based on any of the four attributes defined in the provision policy rule.
Step 12

end

Example:


Device(config-dial-peer)# end

Exits dial peer configuration mode and enters privileged EXEC mode.

Verifying Inbound Leg Headers for Outbound Dial-Peer Matching

SUMMARY STEPS

  1. show dialplan incall {sip | h323} {calling | called} e164-pattern | include voice
  2. show dialplan dialpeer inbound-dial-peer-id number e164-pattern [timeout] | include Voice
  3. show voice class dial-peer provision-policy

DETAILED STEPS

Step 1

show dialplan incall {sip | h323} {calling | called} e164-pattern | include voice

Displays inbound dial peers based on an incoming calling or called number. Once you have the dial peer number, you can use it to search for the complete dial-peer details in the running-config.

Example:

Device# show dialplan incall sip calling 3333 | include Voice

VoiceOverIpPeer1

Device# show dialplan incall sip calling 4444 | include Voice

VoiceOverIpPeer1

Device# show running-config | section dial-peer voice 1 voip

dial-peer voice 1 voip
 destination dpg 10000
 incoming calling e164-pattern-map 100
 dtmf-relay rtp-nte
 codec g711ulaw

Device# show dialplan incall sip called 6000 timeout | include Voice

VoiceOverIpPeer100

Device# show running-config | section dial-peer voice 100 voip

dial-peer voice 100 voip
 incoming called e164-pattern-map 1
 incoming calling e164-pattern-map 1
 dtmf-relay rtp-nte
 codec g711ulaw

Device#  show dialplan incall voip calling 23456

VoiceOverIpPeer1234567
        peer type = voice, system default peer = FALSE, information type = voice,
        description = `',
        tag = 1234567, destination-pattern = `',
        destination e164-pattern-map tag = 200 status = valid,
        destination dpg tag = 200 status = valid,
        voice reg type = 0, corresponding tag = 0,
        allow watch = FALSE
        answer-address = `', preference=0,
        incoming calling e164-pattern-map tag = `200' status = valid,
        CLID Restriction = None
Step 2

show dialplan dialpeer inbound-dial-peer-id number e164-pattern [timeout] | include Voice

Displays a list of outbound dial peers based on a specified inbound dial peer. This command line will be helpful find a list of outbound dial peer of a destination dial-peer group.

Example:

Device# show dialplan dialpeer 1 number 23457 timeout | include Voice 

VoiceOverIpPeer100013
VoiceOverIpPeer100012

Example:

voice class dial-peer provision-policy 2000
 preference 2 diversion to
!
...
!
dial-peer voice 32555 voip
 session protocol sipv2
 session target ipv4:1.5.14.9
 destination uri-diversion 1
 destination uri-to test2
!
dial-peer voice 32991 voip
 destination provision-policy 2000
 incoming called-number 1234
!

Device# show dialplan dialpeer 32991 number 2234 timeout 

Macro Exp.: 2234
Enter Diversion header:sip:1234@cisco.com
Enter To header:sip:2234@10.0.0.0
VoiceOverIpPeer32134
        peer type = voice, system default peer = FALSE, information type = voice,
        description = `',
Step 3

show voice class dial-peer provision-policy

Displays a list of configured provision policies and associated rules.

Example:

Device# show voice class dial-peer provision-policy 

Voice class dial-peer provision-policy: 100		AdminStatus: Up
 Description: match only called

 Pref  Policy Rule
 ----  -----------
 1     called

Voice class dial-peer provision-policy: 101		AdminStatus: Up
 Description: match both calling and called

 Pref  Policy Rule
 ----  -----------
 1     called calling
 
Voice class dial-peer provision-policy: 102		AdminStatus: Up
 Description: match calling first; if no match then match called

 Pref  Policy Rule
 ----  -----------
 1	calling
 2	called

Voice class dial-peer provision-policy: 200		AdminStatus: Up
 Description: match referred-by and via uri; if no match then match request- uri
 
 Pref  Policy Rule
 ----  -----------
 1	referred-by via
 2	uri

voice class dial-peer provision-policy: 300		AdminStatus: Up
 Description: match only request-uri

 Pref  Policy Rule
 ----  -----------
 1	uri

Voice class dial-peer provision-policy: 400		AdminStatus: Up
 Description: match only request uri; if no match then match called

 Pref  Policy Rule
 ----  -----------
 1	uri
 2	called

Configuration Example: Inbound Leg Headers for Outbound Dial-Peer Matching

Example: Configuring Inbound Called or Calling Numbers Used for Outbound Dial-Peer Matching 

Device> enable
Device# configure terminal

Device(config)# voice class dial-peer provision-policy 200
Device(voice-class)# description match both calling and called
Device(voice-class)# preference 2 calling called
Device(voice-class)# exit

Device(config)# voice class e164-pattern-map 300
Device(voice-class)# description patterns
Device(voice-class)# e164 5557123
Device(voice-class)# e164 5558123
Device(voice-class)# e164 5559123
Device(voice-class)# exit

!Associating the Provision Policy with an Inbound Dial Peer
Device(config)# dial-peer voice 100 voip
Device(config-dial-peer)# destination provision-policy 200
Device(config-dial-peer)# end

!Associates a Pattern Map with an Outbound Dial Peer.  
! The called number in the SIP headers of the inbound leg is matched to select the below outbound dial peer.
Device(config)# dial-peer voice 200 voip
Device(config-dial-peer)# destination e164-pattern-map 300
Device(config-dial-peer)# end

Example: Configuring Inbound SIP Headers for Outbound Dial-Peer Matching 

Device> enable
Device# configure terminal

Device(config)# voice class dial-peer provision-policy 200
Device(voice-class)# description match both calling and called
Device(voice-class)# preference 2 via from
Device(voice-class)# exit

!Associating the Provision Policy with an Inbound Dial Peer
Device(config)# dial-peer voice 100 voip
Device(config-dial-peer)# destination provision-policy 200
Device(config-dial-peer)# end

Device(config)# voice class uri 200 sip
Device(config-voice-uri-clas)# pattern 25054..

!Associates a Provision Policy with an Outbound Dial Peer.  
The FROM SIP headers of the inbound leg is matched to select the below outbound dial peer.
Device(config)# dial-peer voice 200 voip
Device(config-dial-peer)# destination uri-from 200
Device(config-dial-peer)# end