Support for P-LTE-450 Pluggable Interface Module

Support for P-LTE-450 Pluggable Interface Module

The Cisco Catalyst IR1800 Rugged Series Router now supports the 450MHz category P Long-Term Evolution (LTE) Pluggable Interface Module (PIM), referred to as P-LTE-450. The LTE-450 PIM uses the 450MHz frequency to address LTE use cases primarily targeting utility, public safety, and critical infrastructure maintained by public organizations in Europe and other countries. The module supports only Band 31 and 72, which are the LTE operating frequency bands. Due to hardware limitations, P-LTE-450 is supported only on slot 0/4.

Unlike regular LTE modules, the P-LTE-450 has some differences on the IOS-XE platform. Some of the key differences are:

  • IP pass through is on Gigabit Ethernet interfaces rather than cellular interfaces.

  • Troubleshooting commands are from the Web user interface of third-party hardware.


Note


Throughout the user documentation, you can see the module referred to as P-LTE-450, the Cisco product name. The module is designed and manufactured by Intelliport, which refers to it as the IPS-701. Both names are present in the documentation.


The show command output displays interface details:

router#show run | sec 0/4/0
interface GigabitEthernet0/4/0
ip address dhcp
negotiation auto
ipv6 dhcp client request vendor
ipv6 address autoconfig
ipv6 enable
interface GigabitEthernet0/4/0.2
encapsulation dot1Q 2
ip address dhcp
ipv6 dhcp client request vendor
ipv6 address autoconfig
 
router#show ip int br
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0/0 10.195.236.86 YES NVRAM up up
GigabitEthernet0/1/0 unassigned YES unset down down
GigabitEthernet0/1/1 unassigned YES unset down down
GigabitEthernet0/1/2 unassigned YES unset up up
GigabitEthernet0/1/3 unassigned YES unset down down
Wl0/1/4 unassigned YES unset up up
GigabitEthernet0/4/0 192.168.200.194 YES DHCP up up
GigabitEthernet0/4/0.2 192.168.4.6 YES DHCP up up
GigabitEthernet0/4/0.3 192.168.5.2 YES DHCP up up
Async0/2/0 unassigned YES unset up down
Vlan1 192.168.50.1 YES NVRAM up up

For more information on how to configure the router interface for the P-LTE-450 module, See

Enhancing P-LTE-450 Network Management Through SNMP MIB Objects

In P-LTE-450 networks, routers can provide crucial quality metrics through Simple Network Management Protocol (SNMP) Management Information Base (MIB) objects. Specifically, Cisco IR1101 and IR1800 routers equipped with the P-LTE-450 Pluggable Interface Module (PIM) allows you to integrate seamlessly with existing SNMP-based management tools to report their status and quality metrics.

The router identifies the P-LTE-450 module as an Ethernet interface, specifically Gigabit Ethernet 0/1/0, rather than a cellular interface.. For LTE450 0/1/0 radio parameters to be supported through SNMP, a new MIB file named Cisco-LTE450-MIB.my needs to be created. This MIB file includes specific fields to capture radio signal quality metrics.

Supported SNMP MIBs

The CISCO-LTE450-MIB SNMP is supported on Cisco P_ LTE_450 MIB .

CISCO-LTE450-MIB supports the following MIB fields:

  • `CiscoLte450Entry `: Main entry point for the MIB

  • `ciscoLte450PortIndex `: Index for the port (GigabitEthernet0/1/0)

  • `ciscoLte450Rssi `: RSSI value

  • `ciscoLte450Rsrp `: RSRP value

  • `ciscoLte450Rsrq `: RSRQ value

  • `ciscoLte450Sinr `: SINR value

  • `ciscoLte450RssiMain `: RSSI value for the main antenna

  • `ciscoLte450RsrpMain `: RSRP value for the main antenna

  • `ciscoLte450RssiAux `: RSSI value for the auxiliary antenna

  • `ciscoLte450RsrpAux `: RSRP value for the auxiliary antenna

View Radio Signal Quality Metrics

The following example displays the signal quality and antenna signal quality of SNMP Cisco 4G LTE 450 configuration:

Router#show lte450 0/1/0 radio
Signal quality
==============
RSSI = -88 dBm
RSRP = -114 dBm
RSRQ = -12 dB
SINR = 0 dB

Antenna signal quality
======================
Main RSSI = -87 dBm
Main RSRP = -112 dBm
Aux RSSI = -104 dBm
Aux RSRP = -143 dBm