Examples

This example shows how to enable AutoQos Wireless Enterprise Policy.

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#wlan wlan1
Switch(config-wlan)#auto qos enterprise

Examples

This example shows how to create a policy map called policy1. When attached to the ingress direction, it matches all the incoming traffic defined in class1, sets the IP Differentiated Services Code Point (DSCP) to 10, and polices the traffic at an average rate of 1 Mb/s and bursts at 20 KB. Traffic exceeding the profile is marked down to a DSCP value gotten from the policed-DSCP map and then sent.

Switch(config)# policy-map policy1
Switch(config-pmap)# class class1
Switch(config-pmap-c)# set dscp 10
Switch(config-pmap-c)# police 1000000 20000 exceed-action policed-dscp-transmit
Switch(config-pmap-c)# exit

This example shows how to configure a default traffic class to a policy map. It also shows how the default traffic class is automatically placed at the end of policy-map pm3 even though class-default was configured first:

Switch# configure terminal 
Switch(config)# class-map cm-3
Switch(config-cmap)# match ip dscp 30
Switch(config-cmap)# exit

Switch(config)# class-map cm-4
Switch(config-cmap)# match ip dscp 40
Switch(config-cmap)# exit

Switch(config)# policy-map pm3
Switch(config-pmap)# class class-default
Switch(config-pmap-c)# set dscp 10
Switch(config-pmap-c)# exit

Switch(config-pmap)# class cm-3
Switch(config-pmap-c)# set dscp 4
Switch(config-pmap-c)# exit

Switch(config-pmap)# class cm-4
Switch(config-pmap-c)# set precedence 5
Switch(config-pmap-c)# exit
Switch(config-pmap)# exit

Switch# show policy-map pm3
Policy Map pm3
  Class cm-3
    set dscp 4
  Class cm-4
    set precedence 5
  Class class-default
    set dscp af11

Examples

This example shows how to configure the class map called class1 with one match criterion, which is an access list called 103:

Switch(config)# access-list 103 permit ip any any dscp 10
Switch(config)# class-map class1
Switch(config-cmap)# match access-group 103
Switch(config-cmap)# exit

This example shows how to delete the class map class1:

Switch(config)# no class-map class1

You can verify your settings by entering the show class-map privileged EXEC command.

Examples

This example shows how to create a class map called class2, which matches all the incoming traffic with DSCP values of 10, 11, and 12:

Switch(config)# class-map class2
Switch(config-cmap)# match ip dscp 10 11 12
Switch(config-cmap)# exit

This example shows how to create a class map called class3, which matches all the incoming traffic with IP-precedence values of 5, 6, and 7:

Switch(config)# class-map class3
Switch(config-cmap)# match ip precedence 5 6 7 
Switch(config-cmap)# exit

This example shows how to delete the IP-precedence match criteria and to classify traffic using acl1:

Switch(config)# class-map class2
Switch(config-cmap)# match ip precedence 5 6 7 
Switch(config-cmap)# no match ip precedence
Switch(config-cmap)# match access-group acl1
Switch(config-cmap)# exit

This example shows how to specify a list of physical ports to which an interface-level class map in a hierarchical policy map applies:

Switch(config)# class-map match-any class4
Switch(config-cmap)# match cos 4
Switch(config-cmap)# exit

This example shows how to specify a range of physical ports to which an interface-level class map in a hierarchical policy map applies:

Switch(config)# class-map match-any class4
Switch(config-cmap)# match cos 4
Switch(config-cmap)# exit

You can verify your settings by entering the show class-map privileged EXEC command.

Examples

This example show how you can configure non-client NRT:

Switch(config)# class-map test_1000
Switch(config-cmap)# match non-client-nrt

Examples

This example show how you can configure user-priority values:

Switch(config)# class-map test_1000
Switch(config-cmap)# match wlan user-priority 7

Examples

This example shows how to create a policy map called policy1. When attached to the ingress port, it matches all the incoming traffic defined in class1, sets the IP DSCP to 10, and polices the traffic at an average rate of 1 Mb/s and bursts at 20 KB. Traffic less than the profile is sent.

Switch(config)# policy-map policy1
Switch(config-pmap)# class class1
Switch(config-pmap-c)# set dscp 10
Switch(config-pmap-c)# police 1000000 20000 conform-action transmit
Switch(config-pmap-c)# exit

This example show you how to configure hierarchical polices:

Switch# configure terminal
Switch(config)# class-map c1
Switch(config-cmap)# exit

Switch(config)# class-map c2
Switch(config-cmap)# exit

Switch(config)# policy-map child
Switch(config-pmap)# class c1
Switch(config-pmap-c)# priority level 1
Switch(config-pmap-c)# police rate percent 20 conform-action transmit exceed action drop
Switch(config-pmap-c-police)# exit
Switch(config-pmap-c)# exit

Switch(config-pmap)# class c2
Switch(config-pmap-c)# bandwidth 20000
Switch(config-pmap-c)# exit

Switch(config-pmap)# class class-default
Switch(config-pmap-c)# bandwidth 20000
Switch(config-pmap-c)# exit
Switch(config-pmap)# exit

Switch(config)# policy-map parent
Switch(config-pmap)# class class-default
Switch(config-pmap-c)# shape average 1000000
Switch(config-pmap-c)# service-policy child
Switchconfig-pmap-c)# end

 

This example shows how to delete a policy map:

Switch(config)# no policy-map policymap2

You can verify your settings by entering the show policy-map privileged EXEC command.

Examples

The following example shows how to configure the priority of the class in policy map policy1:

Switch(config)# class-map cm1
Switch(config-cmap)#match precedence 2
Switch(config-cmap)#exit

Switch(config)#class-map cm2
Switch(config-cmap)#match dscp 30
Switch(config-cmap)#exit

Switch(config)# policy-map policy1
Switch(config-pmap)# class cm1
Switch(config-pmap-c)# priority level 1
Switch(config-pmap-c)# police 1m
Switch(config-pmap-c-police)#exit
Switch(config-pmap-c)#exit
Switch(config-pmap)#exit

Switch(config)#policy-map policy1
Switch(config-pmap)#class cm2
Switch(config-pmap-c)#priority level 2
Switch(config-pmap-c)#police 1m

Examples

The following example sets the queue buffers ratio to 10 percent:

Switch(config)# policy-map policy_queuebuf01
Switch(config-pmap)# class-map class_queuebuf01
Switch(config-cmap)# exit
Switch(config)# policy policy_queuebuf01
Switch(config-pmap)# class class_queuebuf01
Switch(config-pmap-c)# bandwidth percent 80
Switch(config-pmap-c)# queue-buffers ratio 10
Switch(config-pmap)# end

You can verify your settings by entering the show policy-map privileged EXEC command.

Examples

The following example configures a policy map called port-queue to contain policy for a class called dscp-1. The policy for this class is set so that the queue reserved for it has a maximum packet limit of 20 percent:

Switch(config)# policy-map policy11
Switch(config-pmap)# class dscp-1
Switch(config-pmap-c)# bandwidth percent 20
Switch(config-pmap-c)# queue-limit dscp 1 percent 20

Examples

The following command changes the default behavior for trusting wireless traffic to untrust.

Switch(config)# qos wireless-default-untrust

Examples

This example shows how to apply plcmap1 to an physical ingress port:

Switch(config)# interface gigabitethernet2/0/1
Switch(config-if)# service-policy input plcmap1

This example shows how to remove plcmap2 from a physical port:

Switch(config)# interface gigabitethernet2/0/2
Switch(config-if)# no service-policy input plcmap2

The following example displays a VLAN policer configuration. At the end of this configuration, the VLAN policy map is applied to an interface for QoS:

Switch# configure terminal
Switch(config)# class-map vlan100
Switch(config-cmap)# match vlan 100
Switch(config-cmap)# exit
Switch(config)# policy-map vlan100
Switch(config-pmap)# policy-map class vlan100
Switch(config-pmap-c)# police 100000 bc conform-action transmit exceed-action drop
Switch(config-pmap-c-police)# end
Switch# configure terminal
Switch(config)# interface gigabitEthernet1/0/5
Switch(config-if)#  service-policy input vlan100

You can verify your settings by entering the show running-config privileged EXEC command.

Examples

This example shows how to configure the input QoS service policy on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# service-policy input policy-test

This example shows how to disable the input QoS service policy on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no service-policy input policy-test

This example shows how to configure the output QoS service policy on a WLAN to platinum (precious metal policy):

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# service-policy output platinum

Examples

This example shows how to assign DSCP 10 to all FTP traffic without any policers:

Switch(config)# policy-map policy_ftp
Switch(config-pmap)# class-map ftp_class
Switch(config-cmap)# exit
Switch(config)# policy policy_ftp
Switch(config-pmap)# class ftp_class
Switch(config-pmap-c)# set dscp 10
Switch(config-pmap)# exit

You can verify your settings by entering the show policy-map privileged EXEC command.

Examples

This example shows how to display service-policy information for a specific Cisco lightweight access point:

Switch# show ap name 3502b service-policy

NAME: Cisco AP    , DESCR: Cisco Wireless Access Point
PID: 3502I  ,  VID: V01,  SN: FTX1525E94A


NAME: Dot11Radio0    , DESCR: 802.11N 2.4GHz Radio
PID: UNKNOWN,  VID:  ,  SN: FOC1522BLNA


NAME: Dot11Radio1    , DESCR: 802.11N 5GHz Radio
PID: UNKNOWN,  VID:  ,  SN: FOC1522BLNA

Examples

This example shows how to display the service policy that is associated with the access point:

Switch# show ap name test-ap dot11 24ghz service-policy output 

Policy Name  : test-ap1
Policy State : Installed

This example shows how to display the CCX RRM 802.11 configuration for a specific access point:

Switch# show ap name AP01 dot11 24ghz ccx

This example show how to display CDP information for a specific access point:

Switch# show ap name AP01 dot11 24ghz cdp

AP Name               AP CDP State
--------------------- --------------
AP03                  Disabled

This example show how to display the configuration and statistics of 802.11b profiling for a specific access point:

Switch# show ap name AP01 dot11 24ghz profile

 802.11b Cisco AP performance profile mode             : GLOBAL
 802.11b Cisco AP Interference threshold               : 10 %
 802.11b Cisco AP noise threshold                      : -70 dBm
 802.11b Cisco AP RF utilization threshold             : 80 %
 802.11b Cisco AP throughput threshold                 : 1000000 bps
 802.11b Cisco AP clients threshold                    : 12 clients

This example show how to display downstream service policy information for a specific access point:

Switch# show ap name AP01 dot11 24ghz service-policy output

Policy Name  : def-11gn
Policy State : Installed

This example show how to display statistics for a specific access point:

Switch# show ap name AP01 dot11 24ghz stats

Number of Users................................: 0
TxFragmentCount................................: 0
MulticastTxFrameCnt............................: 0
FailedCount....................................: 0
RetryCount.....................................: 0
MultipleRetryCount.............................: 0
FrameDuplicateCount............................: 0
RtsSuccessCount................................: 0
RtsFailureCount................................: 0
AckFailureCount................................: 0
RxIncompleteFragment...........................: 0
MulticastRxFrameCnt............................: 0
FcsErrorCount..................................: 0
TxFrameCount...................................: 0
WepUndecryptableCount..........................: 0
TxFramesDropped................................: 0

Call Admission Control (CAC) Stats
  Voice Bandwidth in use(% of config bw).........: 0
  Video Bandwidth in use(% of config bw).........: 0
  Total BW in use for Voice(%)...................: 0
  Total BW in use for SIP Preferred call(%)......: 0

Load based Voice Call Stats
  Total channel MT free..........................: 0
  Total voice MT free............................: 0
  Na Direct......................................: 0
  Na Roam........................................: 0

WMM TSPEC CAC Call Stats
  Total num of voice calls in progress...........: 0
  Num of roaming voice calls in progress.........: 0
  Total Num of voice calls since AP joined.......: 0
  Total Num of roaming calls since AP joined.....: 0
  Total Num of exp bw requests received..........: 0
  Total Num of exp bw requests admitted..........: 0
  Num of voice calls rejected since AP joined....: 0
  Num of roam calls rejected since AP joined.....: 0
  Num of calls rejected due to insufficent bw....: 0
  Num of calls rejected due to invalid params....: 0
  Num of calls rejected due to PHY rate..........: 0
  Num of calls rejected due to QoS policy........: 0

SIP CAC Call Stats
  Total Num of calls in progress.................: 0
  Num of roaming calls in progress...............: 0
  Total Num of calls since AP joined.............: 0
  Total Num of roaming calls since AP joined.....: 0
  Total Num of Preferred calls received..........: 0
  Total Num of Preferred calls accepted..........: 0
  Total Num of ongoing Preferred calls...........: 0
  Total Num of calls rejected(Insuff BW).........: 0
  Total Num of roam calls rejected(Insuff BW)....: 0

Band Select Stats
  Num of dual band client .......................: 0
  Num of dual band client added..................: 0
  Num of dual band client expired ...............: 0
  Num of dual band client replaced...............: 0
  Num of dual band client detected ..............: 0
  Num of suppressed client ......................: 0
  Num of suppressed client expired...............: 0
  Num of suppressed client replaced..............: 0

This example show how to display the traffic stream configuration for all clients that correspond to a specific access point:

Switch# show ap name AP01 dot11 24ghz tsm all

Examples

This is an example of output from the show class-map command:

Switch# show class-map
 Class Map match-any videowizard_10-10-10-10 (id 2)
   Match access-group name videowizard_10-10-10-10

 Class Map match-any class-default (id 0)
   Match any
 Class Map match-any dscp5 (id 3)
   Match ip dscp 5

Examples

The following is sample output from the show wireless client calls command:

switch# show wireless client calls active

TSPEC Calls:

----------------------------------------------------------------------------
MAC Address     AP Name             Status               WLAN  Authenticated
-----------------------------------------------------------------------------
0000.1515.000f    AP-2           Associated              1  Yes

SIP Calls:
------------------
Number of Active TSPEC calls on 802.11a and 802.11b/g: 1
Number of Active SIP calls on 802.11a and 802.11b/g: 0

Examples

The following is sample output from the show wireless client dot11 command:

Switch# show wireless client dot11 5ghz calls active

 TSPEC Calls:
------------------


SIP Calls:
------------------
Number of Active TSPEC calls on 802.11a: 0
Number of Active SIP calls on 802.11a: 0
 

Examples

This example shows how to display call control and IP-related information about a client:

Switch# show wireless client mac-address  30e4.db41.6157 call-control call-info
Client MAC Address        : 30E4DB416157

Call 1 Statistics

Uplink IP Address         : 209.165.200.225
Downlink IP Address       : 209.165.200.226
Uplink Port               : 29052
Downlink Port             : 27538
Call ID                   : c40acb4d-3b3b0.3d27da1e-356bed03
Called Party              : sip:1011
Calling Party             : sip:1012
Priority                  : 6
Call On Hold              : false
Call Duration             : 30

Call 2 Statistics

No Active Call

Examples

This example shows how to display the TCLAS and user priority-related information about a client:

Switch# show wireless client mac-address 30e4.db41.6157 tclas
MAC Address      UP TID Mask Source IP Addr  Dest IP Addr    SrcPort DstPort Proto
----------------------------------------------------------------------------------
30e4.db41.6157    4   4   95 167838052       2164326668      5060     5060      6
30e4.db41.6157    6   1   31 0               2164326668      0        27538    17

Examples

The following is sample output from the show wireless client voice diagnostics status command:

Switch# show wireless client voice diagnostics status
Voice Diagnostics Status: FALSE

Examples

This is an example of output from the show policy-map interface command, where classification counters are displayed:

Switch# show policy-map interface gigabitethernet1/0/1

  GigabitEthernet1/0/1

  Service-policy input: AutoQos-4.0-CiscoPhone-Input-Policy

    Class-map: AutoQos-4.0-Voip-Data-CiscoPhone-Class (match-any)
      0 packets
      Match: cos  5
        0 packets, 0 bytes
        5 minute rate 0 bps
      QoS Set
        dscp ef
      police:
          cir 128000 bps, bc 8000 bytes
        conformed 0 bytes; actions:
          transmit
        exceeded 0 bytes; actions:
          set-dscp-transmit dscp table policed-dscp
        conformed 0000 bps, exceed 0000 bps

    Class-map: AutoQos-4.0-Voip-Signal-CiscoPhone-Class (match-any)
      0 packets
      Match: cos  3
        0 packets, 0 bytes
        5 minute rate 0 bps
      QoS Set
        dscp cs3
      police:
          cir 32000 bps, bc 8000 bytes
        conformed 0 bytes; actions:
          transmit
        exceeded 0 bytes; actions:
          set-dscp-transmit dscp table policed-dscp
        conformed 0000 bps, exceed 0000 bps

    Class-map: AutoQos-4.0-Default-Class (match-any)
      0 packets
      Match: access-group name AutoQos-4.0-Acl-Default
        0 packets, 0 bytes
        5 minute rate 0 bps
      QoS Set
        dscp default

    Class-map: class-default (match-any)
      0 packets
      Match: any
        0 packets, 0 bytes
        5 minute rate 0 bps

  Service-policy output: AutoQos-4.0-Output-Policy

    queue stats for all priority classes:
      Queueing
      priority level 1

      (total drops) 0
      (bytes output) 0

    Class-map: AutoQos-4.0-Output-Priority-Queue (match-any)
      0 packets
      Match:  dscp cs4 (32) cs5 (40) ef (46)
        0 packets, 0 bytes
        5 minute rate 0 bps
      Match: cos  5
        0 packets, 0 bytes
        5 minute rate 0 bps
      Priority: 30% (300000 kbps), burst bytes 7500000,

      Priority Level: 1

    Class-map: AutoQos-4.0-Output-Control-Mgmt-Queue (match-any)
      0 packets
      Match:  dscp cs2 (16) cs3 (24) cs6 (48) cs7 (56)
        0 packets, 0 bytes
        5 minute rate 0 bps
      Match: cos  3
        0 packets, 0 bytes
        5 minute rate 0 bps
      Queueing
      queue-limit dscp 16 percent 80
      queue-limit dscp 24 percent 90
      queue-limit dscp 48 percent 100
      queue-limit dscp 56 percent 100

      (total drops) 0
      (bytes output) 0
      bandwidth remaining 10%

      queue-buffers ratio 10

    Class-map: AutoQos-4.0-Output-Multimedia-Conf-Queue (match-any)
      0 packets
      Match:  dscp af41 (34) af42 (36) af43 (38)
        0 packets, 0 bytes
        5 minute rate 0 bps
      Match: cos  4
        0 packets, 0 bytes
        5 minute rate 0 bps
      Queueing

      (total drops) 0
      (bytes output) 0
      bandwidth remaining 10%
      queue-buffers ratio 10

    Class-map: AutoQos-4.0-Output-Trans-Data-Queue (match-any)
      0 packets
      Match:  dscp af21 (18) af22 (20) af23 (22)
        0 packets, 0 bytes
        5 minute rate 0 bps
      Match: cos  2
        0 packets, 0 bytes
        5 minute rate 0 bps
      Queueing

      (total drops) 0
      (bytes output) 0
      bandwidth remaining 10%
      queue-buffers ratio 10

    Class-map: AutoQos-4.0-Output-Bulk-Data-Queue (match-any)
      0 packets
      Match:  dscp af11 (10) af12 (12) af13 (14)
        0 packets, 0 bytes
        5 minute rate 0 bps
      Match: cos  1
        0 packets, 0 bytes
        5 minute rate 0 bps
      Queueing

      (total drops) 0
      (bytes output) 0
      bandwidth remaining 4%
      queue-buffers ratio 10

    Class-map: AutoQos-4.0-Output-Scavenger-Queue (match-any)
      0 packets
      Match:  dscp cs1 (8)
        0 packets, 0 bytes
        5 minute rate 0 bps
      Queueing

      (total drops) 0
      (bytes output) 0
      bandwidth remaining 1%
      queue-buffers ratio 10

    Class-map: AutoQos-4.0-Output-Multimedia-Strm-Queue (match-any)
      0 packets
      Match:  dscp af31 (26) af32 (28) af33 (30)
        0 packets, 0 bytes
        5 minute rate 0 bps
      Queueing

      (total drops) 0
      (bytes output) 0
      bandwidth remaining 10%
      queue-buffers ratio 10

    Class-map: class-default (match-any)
      0 packets
      Match: any
        0 packets, 0 bytes
        5 minute rate 0 bps
      Queueing

      (total drops) 0
      (bytes output) 0
      bandwidth remaining 25%
      queue-buffers ratio 25

Examples

This example shows how to display a summary of the WLANs configured on the device:

Switch# show wlan summary
Number of WLANs: 1

WLAN Profile Name                     SSID                           VLAN Status
--------------------------------------------------------------------------------
45   test-wlan                        test-wlan-ssid                  1    UP

This example shows how to display a summary of parameters configured on a particular WLAN:

Switch# show wlan name test-wlan
WLAN Identifier                                : 45
Profile Name                                   : test-wlan
Network Name (SSID)                            : test-wlan-ssid
Status                                         : Enabled
Broadcast SSID                                 : Enabled
Maximum number of Associated Clients           : 0
AAA Policy Override                            : Disabled
Network Admission Control
  NAC-State                                    : Disabled
Number of Active Clients                       : 0
Exclusionlist Timeout                          : 60
Session Timeout                                : 1800 seconds
CHD per WLAN                                   : Enabled
Webauth DHCP exclusion                         : Disabled
Interface                                      : default
Interface Status                               : Up
Multicast Interface                            : test
WLAN IPv4 ACL                                  : test
WLAN IPv6 ACL                                  : unconfigured
DHCP Server                                    : Default
DHCP Address Assignment Required               : Disabled
DHCP Option 82                                 : Disabled
DHCP Option 82 Format                          : ap-mac
DHCP Option 82 Ascii Mode                      : Disabled
DHCP Option 82 Rid Mode                        : Disabled
QoS Service Policy - Input
  Policy Name                                  : unknown
  Policy State                                 : None
QoS Service Policy - Output
  Policy Name                                  : unknown
  Policy State                                 : None
QoS Client Service Policy
  Input  Policy Name                           : unknown
  Output Policy Name                           : unknown
WifiDirect                                     : Disabled
WMM                                            : Disabled
Channel Scan Defer Priority:
  Priority (default)                           : 4
  Priority (default)                           : 5
  Priority (default)                           : 6
Scan Defer Time (msecs)                        : 100
Media Stream Multicast-direct                  : Disabled
CCX - AironetIe Support                        : Enabled
CCX - Gratuitous ProbeResponse (GPR)           : Disabled
CCX - Diagnostics Channel Capability           : Disabled
Dot11-Phone Mode (7920)                        : Invalid
Wired Protocol                                 : None
Peer-to-Peer Blocking Action                   : Disabled
Radio Policy                                   : All
DTIM period for 802.11a radio                  : 1
DTIM period for 802.11b radio                  : 1
Local EAP Authentication                       : Disabled
Mac Filter Authorization list name             : Disabled
Accounting list name                           : Disabled
802.1x authentication list name                : Disabled
Security
    802.11 Authentication                      : Open System
    Static WEP Keys                            : Disabled
    802.1X                                     : Disabled
    Wi-Fi Protected Access (WPA/WPA2)          : Enabled
        WPA (SSN IE)                           : Disabled
        WPA2 (RSN IE)                          : Enabled
            TKIP Cipher                        : Disabled
            AES Cipher                         : Enabled
        Auth Key Management
            802.1x                             : Enabled
            PSK                                : Disabled
            CCKM                               : Disabled
    IP Security                                : Disabled
    IP Security Passthru                       : Disabled
    L2TP                                       : Disabled
    Web Based Authentication                   : Disabled
    Conditional Web Redirect                   : Disabled
    Splash-Page Web Redirect                   : Disabled
    Auto Anchor                                : Disabled
    Sticky Anchoring                           : Enabled
    Cranite Passthru                           : Disabled
    Fortress Passthru                          : Disabled
    PPTP                                       : Disabled
    Infrastructure MFP protection              : Enabled
    Client MFP                                 : Optional
    Webauth On-mac-filter Failure              : Disabled
    Webauth Authentication List Name           : Disabled
    Webauth Parameter Map                      : Disabled
    Tkip MIC Countermeasure Hold-down Timer    : 60
Call Snooping                                  : Disabled
Passive Client                                 : Disabled
Non Cisco WGB                                  : Disabled
Band Select                                    : Disabled
Load Balancing                                 : Disabled
IP Source Guard                                : Disabled
Netflow Monitor                                : test
        Direction                              : Input
        Traffic                                : Datalink

Mobility Anchor List
IP Address
-----------

Examples

The following example configures trust for a Cisco IP phone in Interface GigabitEthernet 1/0/1:

Switch(config)# interface GigabitEthernet1/0/1
Switch(config-if)# trust device cisco-phone

You can verify your settings by entering the show interface status privileged EXEC command.