Configuring UDLD

This chapter describes how to configure the UniDirectional Link Detection (UDLD) and Unidirectional Ethernet on the Catalyst 4500 series switch. It also provides guidelines, procedures, and configuration examples.

This chapter includes the following major sections:

•Overview of UDLD

•Default UDLD Configuration

•Configuring UDLD on the Switch

Note For complete syntax and usage information for the switch commands used in this chapter, first look at the Cisco Catalyst 4500 Series Switch Command Reference and related publications at this location:

http://www.cisco.com/en/US/products//hw/switches/ps4324/index.html

If the command is not found in the Catalyst 4500 Command Reference, it will be found in the larger Cisco IOS library. Refer to the Catalyst 4500 Series Switch Cisco IOS Command Reference and related publications at this location:

http://www.cisco.com/en/US/products/ps6350/index.html

Overview of UDLD

UDLD allows devices connected through fiber-optic or copper Ethernet cables (for example, Category 5 cabling) to monitor the physical configuration of the cables and detect when a unidirectional link exists. A unidirectional link occurs whenever traffic transmitted by the local device over a link is received by the neighbor but traffic transmitted from the neighbor is not received by the local device. When a unidirectional link is detected, UDLD shuts down the affected interface and alerts the user. Unidirectional links can cause a variety of problems, including spanning tree topology loops.

UDLD is a Layer 2 protocol that works with the Layer 1 mechanisms to determine the physical status of a link. At Layer 1, autonegotiation takes care of physical signaling and fault detection. UDLD performs tasks that autonegotiation cannot perform, such as detecting the identities of neighbors and shutting down misconnected interfaces. When you enable both autonegotiation and UDLD, Layer 1 and Layer 2 detections work together to prevent physical and logical unidirectional connections and the malfunctioning of other protocols.

If one of the fiber strands in a pair is disconnected, as long as autonegotiation is active, the link does not stay up. In this case, the logical link is undetermined, and UDLD does not take any action. If both fibers are working normally from a Layer 1 perspective, then UDLD at Layer 2 determines whether or not those fibers are connected correctly and whether or not traffic is flowing bidirectionally between the right neighbors. This check cannot be performed by autonegotiation because autonegotiation operates at Layer 1.

The switch periodically transmits UDLD packets to neighbor devices on interfaces with UDLD enabled. If the packets are echoed back within a specific time frame and they are lacking a specific acknowledgment (echo), the link is flagged as unidirectional and the interface is shut down. Devices on both ends of the link must support UDLD in order for the protocol to successfully identify and disable unidirectional links.

Note By default, UDLD is locally disabled on copper interfaces to avoid sending unnecessary control traffic on this type of media, since it is often used for access interfaces.

Figure 19-1 shows an example of a unidirectional link condition. Switch B successfully receives traffic from Switch A on the interface. However, Switch A does not receive traffic from Switch B on the same interface. UDLD detects the problem and disables the interface.

Figure 19-1 Unidirectional Link

Default UDLD Configuration

Table 19-1 shows the UDLD default configuration.

Table 19-1 UDLD Default Configuration

Feature
Default Status

UDLD global enable state

Globally disabled

UDLD per-interface enable state for fiber-optic media

Enabled on all Ethernet fiber-optic interfaces

UDLD per-interface enable state for twisted-pair (copper) media

Disabled on all Ethernet 10/100 and 1000BaseTX interfaces


Configuring UDLD on the Switch

The following sections describe how to configure UDLD:

•Enabling UDLD Globally

•Enabling UDLD on Individual Interfaces

•Disabling UDLD on Nonfiber-Optic Interfaces

•Disabling UDLD on Fiber-Optic Interfaces

•Resetting Disabled Interfaces

Enabling UDLD Globally

To enable UDLD globally on all fiber-optic interfaces on the switch, perform this task:

Command
Purpose

Switch(config)# [no] udld enable

Enables UDLD globally on fiber-optic interfaces on the switch.

Use the no keyword to globally disable UDLD on fiber-optic interfaces.

Note This command configures only fiber-optic interfaces. An individual interface configuration overrides the setting of this command.


Enabling UDLD on Individual Interfaces

To enable UDLD on individual interfaces, perform this task:

 
Command
Purpose

Step 1 

Switch(config-if)# udld enable

Enables UDLD on a specific interface. On a fiber-optic interface, this command overrides the udld enable global configuration command setting.

Step 2 

Switch# show udld interface

Verifies the configuration.

Disabling UDLD on Nonfiber-Optic Interfaces

To disable UDLD on individual nonfiber-optic interfaces, perform this task:

 
Command
Purpose

Step 1 

Switch(config-if)# no udld enable

Disables UDLD on a nonfiber-optic interface.

Note On fiber-optic interfaces, the no udld enable command reverts the interface configuration to the udld enable global configuration command setting.

Step 2 

Switch# show udld interface

Verifies the configuration.

Disabling UDLD on Fiber-Optic Interfaces

To disable UDLD on individual fiber-optic interfaces, perform this task:

 
Command
Purpose

Step 1 

Switch(config-if)# udld disable

Disables UDLD on a fiber-optic interface.

Note This command is not supported on nonfiber-optic interfaces.

Use the no keyword to revert to the udld enable global configuration command setting.

Step 2 

Switch# show udld interface

Verifies the configuration.

Resetting Disabled Interfaces

To reset all interfaces that have been shut down by UDLD, perform this task:

Command
Purpose 
Switch# udld reset

Resets all interfaces that have been shut down by UDLD.