Catalyst Supervisor Engine 32 PISA IOS Command Reference, 12.2ZY

show cable-diagnostics tdr
show catalyst6000
show cdp neighbors
show cef interface policy-statistics
show class-map
show counters interface
show diagnostic
show diagnostic cns
show diagnostic sanity
show dot1q-tunnel
show dot1x
show dss log
show environment alarm
show environment cooling
show environment status
show environment temperature
show eobc
show erm statistics
show errdisable detect
show errdisable flap-value
show errdisable recovery
show etherchannel
show fm features
show fm inband-counters
show fm insp
show fm interface
show fm ipv6 traffic-filter
show fm nat netflow data
show fm reflexive
show fm summary
show fm vlan
show icc
show idprom
show interfaces
show interfaces accounting
show interfaces capabilities
show interfaces counters
show interfaces debounce
show interfaces description
show interfaces flowcontrol
show interfaces private-vlan mapping
show interfaces status
show interfaces summary
show interfaces switchport
show interfaces switchport backup
show interfaces transceiver
show interfaces trunk
show interfaces unidirectional
show interfaces vlan mapping
show ip arp inspection
show ip arp inspection log
show ip auth-proxy watch-list
show ipc
show ip cache flow
show ip cache verbose flow

show cable-diagnostics tdr

To display the test results for the TDR cable diagnostics, use the show cable-diagnostics tdr command.

show cable-diagnostics tdr {interface {interface interface-number}}

Syntax Description


interface interface	Specifies the interface type; valid values are fastethernet and gigabitethernet.
interface-number	Module and port number.

Command Default

This command has no default settings.

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

The show cable-diagnostics tdr command is supported on specific modules. See the Release Notes for Cisco IOS Release 12.2 ZY Supervisor Engine 32 PISA for the list of the modules that support TDR.

In the event of an open or shorted cable, the accuracy of length of where the cable is open or shorted is plus or minus 2 meters.

The pair length can be displayed in meters (m), centimeters (cm), or kilometers (km).

If the TDR test has not been run on the port, the following message is displayed:

TDR test was never run on Gi2/12

Examples

This example shows how to display the information about the TDR test:

Router> show cable-diagnostics tdr interface gigabitethernet8/1

TDR test last run on: February 25 11:18:31

Interface Speed Pair Cable length        Distance to fault   Channel Pair status

--------- ----- ---- ------------------- ------------------- ------- ------------

Gi8/1     1000  1-2  1    +/- 6  m       N/A                 Pair B  Terminated

                3-4  1    +/- 6  m       N/A                 Pair A  Terminated

                5-6  1    +/- 6  m       N/A                 Pair C  Terminated

                7-8  1    +/- 6  m       N/A                 Pair D  Terminated

Router>

Table 2-32 describes the fields in the show cable-diagnostics tdr command output.

Table 2-32 show cable-diagnostics tdr Command Output Fields
Field	Description
Interface	Interface tested.
Speed	Current line speed.
Pair	Local pair name.
Cable Length	Cable length and accuracy. The accuracy unit is displayed in meters (m), centimeters (cm), or kilometers (km).
Channel	Pair designation.
Pair status	Pair status displayed is one of the following: •Terminated—The link is up. •Shorted—A short is detected on the cable. •Open—An opening is detected on the cable. •Not Completed—The test on the port failed. •Not Supported—The test on the port is not supported. •Broken—The pair is bad—either open or shorted. •ImpedanceMis—The impedance is mismatched. •InProgress—The diagnostic test is in progress.

Related Commands


Command	Description
clear cable-diagnostics tdr	Clears a specific interface or clears all interfaces that support TDR.
test cable-diagnostics	Tests the condition of 10-Gigabit Ethernet links or copper cables on 48-port 10/100/1000 BASE-T modules.

show catalyst6000

To display the information about the Catalyst 6500 series switch, use the show catalyst6000 command.

show catalyst6000 {all | chassis-mac-address | switching-clock | traffic-meter}

Syntax Description


all	Displays the MAC-address ranges and the current and peak traffic-meter reading.
chassis-mac-address	Displays the MAC-address range.
switching-clock	Displays the failure recovery mode of the switching clock.
traffic-meter	Displays the percentage of the backplane (shared bus) utilization.

Command Default

all

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

If you enter the switching-clock keywords, the Catalyst 6500 series switch displays whether switching of the redundant clock sources on the backplane is allowed if the active clock source fails.

The Catalyst 6500 series switch has either 64 or 1024 MAC addresses that are available to support the software features. You can enter the show catalyst6000 chassis-mac-address command to display the MAC-address range on your chassis.

Examples

This example shows how to display the MAC-address ranges and the current and peak traffic-meter readings:

Router> show catalyst6000 all

  chassis MAC addresses: 64 addresses from 0001.6441.60c0 to 0001.6441.60ff

  traffic meter =   0%  Never cleared

           peak =   0%  reached at 08:14:38 UTC Wed Mar 19 2003

  switching-clock: clock switchover and system reset is allowed

Router>

This example shows how to display the MAC-address ranges:

Router# show catalyst6000 chassis-mac-address

  chassis MAC addresses: 1024 addresses from 00d0.004c.1800 to 00d0.004c.1c00

Router#

This example shows how to display the current and peak traffic-meter readings:

Router> show catalyst6000 traffic-meter

  traffic meter = 0%   peak = 0%  at  09:57:58 UTC Mon Nov 6 2000

Router#

This example shows how to display the failure recovery mode of the switching clock:

Router> show catalyst6000 switching-clock

  switching-clock: clock switchover and system reset is allowed

Router>

show cdp neighbors

To display detailed information about the neighboring devices that are discovered through CDP, use the show cdp neighbors command.

show cdp neighbors [type number] [detail]

Syntax Description


type	(Optional) Interface type that is connected to the neighbors about which you want information; possible valid values are ethernet, fastethernet, gigabitethernet, tengigabitethernet, port-channel, and vlan.
number	(Optional) Interface number that is connected to the neighbors about which you want information.
detail	(Optional) Displays detailed information about a neighbor (or neighbors) including the network address, the enabled protocols, the hold time, and the software version.

Command Default

This command has no default settings.

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

The port-channel values are from 0 to 282; values from 257 to 282 are supported on the CSM and the FWSM only.

Examples

This example shows how to display the information about the CDP neighbors:

Router# show cdp neighbors

Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge

                  S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone

Device ID        Local Intrfce     Holdtme    Capability  Platform  Port ID

lab-7206         Eth 0              157          R        7206VXR   Fas 0/0/0

lab-as5300-1     Eth 0              163          R        AS5300    Fas 0

lab-as5300-2     Eth 0              159          R        AS5300    Eth 0

lab-as5300-3     Eth 0              122          R        AS5300    Eth 0

lab-as5300-4     Eth 0              132          R        AS5300    Fas 0/0

lab-3621         Eth 0              140         R S       3631-telcoFas 0/0

008024 2758E0    Eth 0              132          T        CAT3000   1/2

Table 2-33 describes the fields that are shown in the example.

Table 2-33 show cdp neighbors Field Descriptions
Field	Definition
Device ID	Configured ID (name), MAC address, or serial number of the neighbor device.
Local Intrfce	(Local Interface) The protocol that is used by the connectivity media.
Holdtme	(Holdtime) Remaining amount of time, in seconds, that the current device holds the CDP advertisement from a transmitting router before discarding it.
Capability	Capability code that is discovered on the device. This device type is listed in the CDP Neighbors table. Possible values are as follows: R—Router T—Transparent bridge B—Source-routing bridge S—Switch H—Host I—IGMP device r—Repeater P—Phone
Platform	Product number of the device.
Port ID	Protocol and port number of the device.

This example shows how to display detailed information about your CDP neighbors:

Router# show cdp neighbors detail

-------------------------

Device ID: lab-7206

Entry address(es):

  IP address: 172.19.169.83

Platform: cisco 7206VXR,  Capabilities: Router

Interface: Ethernet0,  Port ID (outgoing port): FastEthernet0/0/0

Holdtime : 123 sec

Version :

Cisco Internetwork Operating System Software

IOS (tm) 5800 Software (C5800-P4-M), Version 12.1(2)

Copyright (c) 1986-2002 by Cisco Systems, Inc.

advertisement version: 2

Duplex: half

-------------------------

Device ID: lab-as5300-1

Entry address(es):

  IP address: 172.19.169.87

Table 2-34 describes the fields that are shown in the example.

Table 2-34 show cdp neighbors detail Field Descriptions
Field	Definition
Device ID	Name of the neighbor device and either the MAC address or the serial number of this device.
Entry address(es)	List of network addresses of neighbor devices.
[network protocol] address	Network address of the neighbor device. The address can be in IP, IPX, AppleTalk, DECnet, or CLNS protocol conventions.
Platform	Product name and number of the neighbor device.
Capabilities	Device type of the neighbor. This device can be a router, a bridge, a transparent bridge, a source-routing bridge, a switch, a host, an IGMP device, or a repeater.
Interface	Protocol and port number of the port on the current device.
Holdtime	Remaining amount of time, in seconds, that the current device holds the CDP advertisement from a transmitting router before discarding it.
Version:	Software version running on the neighbor device.
advertisement version:	Version of CDP that is being used for CDP advertisements.
Duplex:	Duplex state of connection between the current device and the neighbor device.

Related Commands


Command	Description
show cdp	Displays global CDP information.
show cdp entry	Displays information about a specific neighboring device discovered using CDP.
show cdp interface	Displays information about the interfaces on which CDP is enabled.
show cdp traffic	Displays information about traffic between devices gathered using CDP.

show cef interface policy-statistics

To display the per-interface traffic statistics, use the show cef interface policy-statistics command.

show cef interface policy-statistics

Syntax Description

This command has no keywords or arguments.

Command Default

This command has no default settings.

Command Default

User EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Examples

This example shows how to display the per-interface traffic statistics:

Router# show cef interface policy-statistics

POS7/0 is up (if_number 7)

Bucket 	Packets	Bytes

1 	0 	0

2 	0	0

3 	0 	0

4 	0 	0

5 	100 	10000

6 	0 	0

7 	0 	0

8 	0 	0

Router#

show class-map

To display class-map information, use the show class-map command.

show class-map [class-name]

Syntax Description


class-name	(Optional) Name of the class map.

Command Default

This command has no default settings.

Command Default

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Examples

This example shows how to display class-map information for all class maps:

Router# show class-map

 Class Map match-any class-default (id 0)

   Match any

 Class Map match-any class-simple (id 2)

   Match any

 Class Map match-all ipp5 (id 1)

   Match ip precedence 5

 Class Map match-all agg-2 (id 3)

Router#

This example shows how to display class-map information for a specific class map:

Router# show class-map ipp5

 Class Map match-all ipp5 (id 1)

   Match ip precedence 5

Router#

Related Commands


Command	Description
class-map	Accesses the QoS class map configuration mode to configure QoS class maps.
show policy-map	Displays information about the policy map.
show policy-map interface	Displays the statistics and the configurations of the input and output policies that are attached to an interface.

show counters interface

To display the information about the interface counter, use the show counters interface command.

show counters interface {type mod/port} [delta]

Syntax Description


type	Interface type; possible valid values are ethernet, fastethernet, gigabitethernet, tengigabitethernet, port-channel, pos, atm, null, tunnel, and ge-wan.
mod/port	Module and port number.
delta	(Optional) Displays the interface counters values since the last clear counters command.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

The show counters interface command is not supported on SVIs.

The show counters interface delta command displays a detailed list of the last-saved counter values.

Examples

This example shows how to display the information about the interface counter:

Router# show counters interface fastethernet 5/2

64 bit counters:

 0.                      rxHCTotalPkts = 1

 1.                      txHCTotalPkts = 1

 2.                    rxHCUnicastPkts = 0

 3.                    txHCUnicastPkts = 0

 4.                  rxHCMulticastPkts = 0

 5.                  txHCMulticastPkts = 0

 6.                  rxHCBroadcastPkts = 1

 7.                  txHCBroadcastPkts = 1

 8.                         rxHCOctets = 78

 9.                         txHCOctets = 78

10.                 rxTxHCPkts64Octets = 0

11.            rxTxHCPkts65to127Octets = 2

12.           rxTxHCPkts128to255Octets = 0

13.           rxTxHCPkts256to511Octets = 0

14.          rxTxHCpkts512to1023Octets = 0

15.         rxTxHCpkts1024to1518Octets = 0

16.                    txHCTrunkFrames = 0

17.                    rxHCTrunkFrames = 0

18.                     rxHCDropEvents = 0

32 bit counters:

 0.                   rxCRCAlignErrors = 0

 1.                   rxUndersizedPkts = 0

 2.                    rxOversizedPkts = 0

 3.                     rxFragmentPkts = 0

 4.                          rxJabbers = 0

 5.                       txCollisions = 0

 6.                         ifInErrors = 0

 7.                        ifOutErrors = 0

 8.                       ifInDiscards = 0

 9.                  ifInUnknownProtos = 0

10.                      ifOutDiscards = 0

11.            txDelayExceededDiscards = 0

12.                              txCRC = 0

13.                         linkChange = 1

14.                   wrongEncapFrames = 0

All Port Counters

 1.                          InPackets = 1

 2.                           InOctets = 78

 3.                        InUcastPkts = 0

 4.                        InMcastPkts = 0

 5.                        InBcastPkts = 1

 6.                         OutPackets = 1

 7.                          OutOctets = 78

 8.                       OutUcastPkts = 0

 9.                       OutMcastPkts = 0

10.                       OutBcastPkts = 1

11.                           AlignErr = 0

12.                             FCSErr = 0

13.                            XmitErr = 0

14.                             RcvErr = 0

15.                          UnderSize = 0

16.                          SingleCol = 0

17.                           MultiCol = 0

18.                            LateCol = 0

19.                       ExcessiveCol = 0

20.                       CarrierSense = 0

21.                              Runts = 0

22.                             Giants = 0

23.                         InDiscards = 0

24.                        OutDiscards = 0

25.                           InErrors = 0

26.                          OutErrors = 0

27.                      TrunkFramesTx = 0

28.                      TrunkFramesRx = 0

29.                         WrongEncap = 0

30.     Broadcast_suppression_discards = 0

31.     Multicast_suppression_discards = 0

32.       Unicast_suppression_discards = 0

33.                 rxTxHCPkts64Octets = 0

34.            rxTxHCPkts65to127Octets = 2

35.           rxTxHCPkts128to255Octets = 0

36.           rxTxHCPkts256to511Octets = 0

37.          rxTxHCpkts512to1023Octets = 0

38.         rxTxHCpkts1024to1518Octets = 0

39.                         DropEvents = 0

40.                     CRCAlignErrors = 0

41.                     UndersizedPkts = 0

42.                      OversizedPkts = 0

43.                       FragmentPkts = 0

44.                            Jabbers = 0

45.                         Collisions = 0

46.              DelayExceededDiscards = 0

47.                        bpduOutlost = 0

48.                        qos0Outlost = 0

49.                        qos1Outlost = 0

50.                        qos2Outlost = 0

51.                        qos3Outlost = 0

52.                    bpduCbicOutlost = 0

53.                    qos0CbicOutlost = 0

54.                    qos1CbicOutlost = 0

55.                    qos2CbicOutlost = 0

56.                    qos3CbicOutlost = 0

57.                         bpduInlost = 0

58.                         qos0Inlost = 0

59.                         qos1Inlost = 0

60.                         qos2Inlost = 0

61.                         qos3Inlost = 0

62.                         qos4Inlost = 0

63.                         qos5Inlost = 0

64.                         qos6Inlost = 0

65.                         qos7Inlost = 0

66.                         pqueInlost = 0

67.                           Overruns = 0

68.                           maxIndex = 0

Router#

This example shows how to display the values for the interface counters since the last clear counters command:

Router# show counters interface gigabitethernet5/2 delta

Time since last clear

---------------------

1d08h

64 bit counters:

0. rxHCTotalPkts = 508473

1. txHCTotalPkts = 2366

2. rxHCUnicastPkts = 411611

3. txHCUnicastPkts = 193

4. rxHCMulticastPkts = 81868

5. txHCMulticastPkts = 2155

6. rxHCBroadcastPkts = 14994

7. txHCBroadcastPkts = 18

8. rxHCOctets = 36961992

Router#

Related Commands


Command	Description
clear counters	Clears the interface counters.

show diagnostic

To view the test results of the online diagnostics and list the supported test suites, use the show diagnostic command.

show diagnostic bootup level

show diagnostic content [module num]

show diagnostic events [module num] [event-type event-type]

show diagnostic {ondemand settings}

show diagnostic {result [module num] [detail]}

show diagnostic schedule [module num]

Syntax Description


bootup level	Displays the coverage level for the configured boot-up diagnostics.
content	Displays test information including test ID, test attributes, and supported coverage test levels for each test and for all modules.
module num	(Optional) Specifies the module number.
events	Displays the event log for the diagnostic events.
event-type event-type	(Optional) Specifies the event type; valid values are error, info, and warning.
ondemand settings	Displays the settings for the ondemand diagnostics.
result	Displays the test results.
detail	(Optional) Displays the test statistics of each test.
schedule	Displays the current scheduled diagnostic tasks.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

If you do not enter a module num, information for all modules is displayed.

In the command output, the possible testing results are as follows:

•Passed (.)

•Failed (F)

•Unknown (U)

Examples

This example shows how to display the test suite and the monitoring interval and test attributes:

Router# show diagnostic content module 1

Diagnostic Tests List for Module 1:

Module 1:

  Diagnostics test suite attributes:

    M/C/* - Minimal level test / Complete level test / Not applicable

      B/* - Bypass bootup test / Not applicable

      P/* - Per port test / Not applicable

      D/N - Disruptive test / Non-disruptive test

      S/* - Only applicable to standby unit / Not applicable

      X/* - Not a health monitoring test / Not applicable

      F/* - Fixed monitoring interval test / Not applicable

      E/* - Always enabled monitoring test / Not applicable

      A/I - Monitoring is active / Monitoring is inactive

Testing Interval

  ID  Test Name                          Attributes (day hh:mm:ss.ms)

  === ================================== ========== =================

   1) TestDummy1 ----------------------> M**D****A  000 00:01:00.000

   2) TestDummy2 ----------------------> M**D**FEA  000 00:02:30.000

   3) TestGBICIntegrity ---------------> *BPD****I  not configured

   4) TestActiveToStandbyLoopback -----> M*PDS***I  not configured

   5) TestLoopback --------------------> M*PD****I  not configured

   6) TestNewLearn --------------------> M**N****I  not configured

   7) TestIndexLearn ------------------> M**N****I  not configured

   8) TestConditionalLearn ------------> M**N****I  not configured

   9) TestBadBpdu ---------------------> M**D****I  not configured

  10) TestCapture ---------------------> M**D****I  not configured

  11) TestProtocolMatch ---------------> M**D****I  not configured

  12) TestChannel ---------------------> M**D****I  not configured

  13) TestDontShortcut ----------------> M**Nrefer*I  not configured

  14) TestL3Capture2 ------------------> M**N****I  not configured

  15) TestL3VlanMet -------------------> M**N****I  not configured

  16) TestIngressSpan -----------------> M**N****I  not configured

  17) TestEgressSpan ------------------> M**N****I  not configured

  18) TestAclPermit -------------------> M**N****I  not configured

  19) TestAclDeny ---------------------> M**D****I  not configured

  20) TestNetflowInlineRewrite --------> C*PD****I  not configured

Router#

This example shows how to display the configured boot-up diagnostic level:

Router# show diagnostic bootup level

Current Bootup Diagnostic Level = Complete

Router#

This example shows how to display the event log for the diagnostics:

Router# show diagnostic events

Diagnostic events (storage for 500 events, 10 events recorded)

Event Type (ET):I - Info, W - Warning, E - Error

Time Stamp         ET [Card] Event Message

------------------ --  --------------------------------------------------------

08/26 15:51:04.335 I  [1] TestIndexLearn Passed

08/26 15:51:04.335 I  [1] Diagnostics Passed

08/26 15:51:15.511 I  [8] TestLoopback Passed

08/26 15:51:15.511 I  [8] Diagnostics Passed

08/26 16:15:02.247 I  [1] TestDontLearn Passed

08/26 16:15:02.247 I  [1] Diagnostics Passed

08/26 16:15:12.683 I  [8] TestNetflowInlineRewrite Passed

08/26 16:15:12.683 I  [8] Diagnostics Passed

08/26 16:15:42.207 I  [2] TestActiveToStandbyLoopback Passed

08/26 16:15:42.207 I  [2] Diagnostics Passed

Router#

This example shows how to display the settings for the ondemand diagnostics:

Router# show diagnostic ondemand settings

Ondemand Run Iteration   = 2

Ondemand Action-on-Error = CONTINUE

Router#

This example shows how to display the current scheduled diagnostic tasks for the specified slot:

Router# show diagnostic schedule module 1

Current Time = 07:55:30 UTC Fri August 2 2002

Diagnostic for Module 1:

Schedule #1:

        To be run on January 3 2003 23:32

        Test ID(s) to be executed:1.

Schedule #2:

        To be run daily 14:45

        Test ID(s) to be executed:2.

Schedule #3:

        To be run weekly Monday 3:33

        Test ID(s) to be executed:all.

Router#

This example shows how to display the testing results for the specified slot:

Router# show diagnostic result module 3

Current bootup diagnostic level:complete

Module 3:

  Overall Diagnostic Result for Module 8 :PASS

  Diagnostic level at card bootup:complete

  Test results:(. = Pass, F = Fail, U = Untested)

   1) TestLoopback :

      Port  1  2  3  4  5  6  7  8  9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

      ----------------------------------------------------------------------------

            .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .

      Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

      ----------------------------------------------------------------------------

            .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .

   2) TestNewLearn --------------------> .

   3) TestIndexLearn ------------------> .

   4) TestDontLearn -------------------> .

   5) TestConditionalLearn ------------> .

6) TestDontLearn -------------------> .

   7) TestConditionalLearn ------------> .

   8) TestBadBpdu ---------------------> .

   9) TestTrap ------------------------> .

  10) TestMatch -----------------------> .

  11) TestCapture ---------------------> .

  12) TestProtocolMatch ---------------> .

  13) TestChannel ---------------------> .

  14) TestIPFibShortcut ---------------> .

  15) TestDontShortcut ----------------> .

  16) TestL3Capture2 ------------------> .

  17) TestL3VlanMet -------------------> .

  18) TestIngressSpan -----------------> .

  19) TestEgressSpan ------------------> .

  20) TestAclPermit -------------------> .

  21) TestAclDeny ---------------------> .

  22) TestNetflowInlineRewrite:

      Port  1  2  3  4  5  6  7  8  9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

      ----------------------------------------------------------------------------

            .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .

      Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

      ----------------------------------------------------------------------------

            .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .

Router#

This example shows how to display the detailed testing results for the specified slot:

Router# show diagnostic result module 1 detail

Current bootup diagnostic level:complete

Module 1:

  Overall Diagnostic Result for Module 1 :PASS

  Diagnostic level at card bootup:complete

  Test results:(. = Pass, F = Fail, U = Untested)

___________________________________________________________________________

   1) TestDummy -----------------------> .

          Error code ------------------> 0 (DIAG_SUCCESS)

          Total run count -------------> 90

          Last test execution time ----> Dec 10 2002 12:34:30

          First test failure time -----> Dec 10 2002 11:57:39

          Last test failure time ------> Dec 10 2002 12:34:10

          Last test pass time ---------> Dec 10 2002 11:34:30

          Total failure count ---------> 65

          Consecutive failure count ---> 0

___________________________________________________________________________

 2) TestLoopback:

      Port  1  2

      ----------

            .  .

          Error code ------------------> 0 (DIAG_SUCCESS)

          Total run count -------------> 1

          Last test execution time ----> Dec 10 2002 12:37:18

          First test failure time -----> n/a

          Last test failure time ------> n/a

          Last test pass time ---------> Dec 10 2002 12:37:18

          Total failure count ---------> 0

          Consecutive failure count ---> 0

Router#

This example shows how to display the event logs for the diagnostics:

Router# show diagnostic events

Diagnostic events (storage for 500 events, 10 events recorded)

EventType:I - Info, W - Warning, E - Error

TimeStamp          Type [Card] EventMessage

08/26 15:51:04.335 I    [1] TestIndexLearn Passed

08/26 15:51:04.335 I    [1] Diagnostics Passed

08/26 15:51:15.511 I    [8] TestLoopback Passed

08/26 15:51:15.511 I    [8] Diagnostics Passed

08/26 16:15:02.247 I    [1] TestDontLearn Passed

08/26 16:15:02.247 I    [1] Diagnostics Passed

08/26 16:15:12.683 I    [8] TestNetflowInlineRewrite Passed

08/26 16:15:12.683 I    [8] Diagnostics Passed

08/26 16:15:42.207 I    [2] TestActiveToStandbyLoopback Passed

08/26 16:15:42.207 I    [2] Diagnostics Passed

Router#

Related Commands


Command	Description
diagnostic bootup level	Sets the bootup diagnostic level.
diagnostic cns	Configures the CNS diagnostics.
diagnostic event-log size	Modifies the diagnostic event-log size dynamically.
diagnostic monitor	Configures the health-monitoring diagnostic testing.
diagnostic ondemand	Configures the ondemand diagnostics.
diagnostic schedule test	Sets the scheduling of test-based diagnostic testing for a specific module or schedules a supervisor engine switchover.
diagnostic start	Runs the specified diagnostic test.
diagnostic stop	Stops the testing process.

show diagnostic cns

To display the information about the CNS subject, use the show diagnostic cns command.

show diagnostic cns {publish | subscribe}

Syntax Description


publish	Displays the subject with which the diagnostic results is published.
subscribe	Displays the subscribed subjects.

Command Default

This command has no default settings.

Command Default

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

The CNS subsystem communicates with remote network applications through the CNS-event agent and follows the publish and subscribe model. An application sets itself up to receive events by subscribing to the approprate event subject name.

Examples

This example shows how to display the subject with which the diagnostic results is published:

Router# show diagnostic cns publish

Subject: cisco.cns.device.diag_results

Router#

This example shows how to display the subscribed subject:

Router# show diagnostic cns subscribe

Subject: cisco.cns.device.diag_get_results

Router#

Related Commands


Command	Description
diagnostic cns	Configures the CNS diagnostics.

show diagnostic sanity

To display sanity check results, use the show diagnostic sanity command.

show diagnostic sanity

Syntax Description

This command has no arguments or keywords.

Command Default

If you enter this command without any arguments, it displays information for all the Gigabit Ethernet WAN interfaces in the Catalyst 6500 series switch.

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

The sanity check runs a set of predetermined checks on the configuration with a possible combination of certain system states to compile a list of warning conditions. The checks are designed to look for anything that seems out of place and are intended to serve as an aid to maintaining the system sanity.

The following is a list of the checks that are run and the action taken when the condition is found:

•Checks whether the default gateways are reachable. If so, the system stops pinging.

•If a port autonegotiates to half duplex, the system flags it.

Trunking Checks

•If a trunk port has the mode set to on, the system flags it.

•If a port is trunking and mode is auto, the system flags it.

•If a trunk port is not trunking and the mode is desirable, the system flags it.

•If a trunk port negotiates to half duplex, the system flags it.

Channeling Checks

•If a port has channeling mode set to on, the system flags it.

•If a port is not channeling and the mode is set to desirable, the system flags it.

•If a VLAN has a spanning-tree root of 32K (root is not set), the system flags it.

Spanning-tree VLAN Checks

•If a VLAN has a max age on the spanning-tree root that is different than the default, the system flags it.

•If a VLAN has a fwd delay on the spanning-tree root that is different than the default, the system flags it.

•If a VLAN has a fwd delay on the bridge that is different than the default, the system flags it.

•If a VLAN has a hello time on the bridge that is different than the default, the system flags it.

Spanning-tree Port Checks

•If a port has a port cost that is different than the default, the system flags it.

•If a port has a port priority that is different than the default, the system flags it.

UDLD Checks

•If a port has UDLD disabled, the system flags it.

•If a port had UDLD shut down, the system flags it.

•If a port had a UDLD undetermined state, the system flags it.

Assorted Port Checks

•If a port had receive flow control disabled, the system flags it.

•If a trunk port had PortFast enabled, the system flags it.

•The system flags it if an inline power port has any of the following states:

–denied

–faulty

–other

–off

•If a port has a native VLAN mismatch, the system flags it.

•If a port has a duplex mismatch, the system flags it.

Bootstring and Config Register Checks

•The config register on the primary supervisor engine (and on the secondary supervisor engine if present) must be one of the following values: 0x2 , 0x102, or 0x2102.

•The system verifies the bootstring on the primary supervisor engine (and on the secondary supervisor engine if present). The system displays a message if the bootstring is empty.

•The system verifies that every file is specified in the bootstring. The system displays a message if the file is absent or shows up with a wrong checksum.

If only device: is specified as a filename, then the system verifies that the first file is on the device.

Assorted Checks

•The system displays a message if IGMP snooping is disabled.

•The system displays a message if any of the values of the snmp community access strings {RO,RW,RW-ALL} is the same as the default.

•The system displays a message if any of the modules are in states other than "Ok."

•The system displays a message that lists all the tests that failed (displayed as an "F") in the show test all command.

•The system displays a message if *fast is not configured on the switch anywhere.

•The system displays a message if there is enough room for the crashinfo file on the bootflash:.

•The system displays a message if multicast routing is enabled globally but is not applied to all interfaces.

•The system displays a message if IGMP snooping is disabled and RGMP is enabled.

Examples

This example displays samples of the messages that could be displayed with the show diagnostic sanity command:

Router# show diagnostic sanity

Pinging default gateway 10.6.141.1 ....

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.6.141.1, timeout is 2 seconds:

..!!.

Success rate is 0 percent (0/5)

IGMP snooping disabled please enable it for optimum config.

IGMP snooping disabled but RGMP enabled on the following interfaces,

please enable IGMP for proper config :

Vlan1, Vlan2, GigabitEthernet1/1

Multicast routing is enabled globally but not enabled on the following

interfaces:

GigabitEthernet1/1, GigabitEthernet1/2

A programming algorithm mismatch was found on the device bootflash:

Formatting the device is recommended.

The bootflash: does not have enough free space to accomodate the crashinfo file.

Please check your confreg value : 0x0.

Please check your confreg value on standby: 0x0.

The boot string is empty. Please enter a valid boot string .

Could not verify boot image "disk0:" specified in the boot string on the

slave.

Invalid boot image "bootflash:asdasd" specified in the boot string on the

slave.

Please check your boot string on the slave.

UDLD has been disabled globally - port-level UDLD sanity checks are

being bypassed.

OR

The following ports have UDLD disabled. Please enable UDLD for optimum

config:

Fa9/45

The following ports have an unknown UDLD link state. Please enable UDLD

on both sides of the link:

Fa9/45

The following ports have portfast enabled:

Fa9/35, Fa9/45

The following ports have trunk mode set to on:

Fa4/1, Fa4/13

The following trunks have mode set to auto:

Fa4/2, Fa4/3

The following ports with mode set to desirable are not trunking:

Fa4/3, Fa4/4

The following trunk ports have negotiated to half-duplex:

Fa4/3, Fa4/4

The following ports are configured for channel mode on:

Fa4/1, Fa4/2, Fa4/3, Fa4/4

The following ports, not channeling are configured for channel mode

desirable:

Fa4/14

The following vlan(s) have a spanning tree root of 32768:

The following vlan(s) have max age on the spanning tree root different from

the default:

1-2

The following vlan(s) have forward delay on the spanning tree root different

from the default:

1-2

The following vlan(s) have hello time on the spanning tree root different

from the default:

1-2

The following vlan(s) have max age on the bridge different from the

default:

1-2

The following vlan(s) have fwd delay on the bridge different from the

default:

1-2

The following vlan(s) have hello time on the bridge different from the

default:

1-2

The following vlan(s) have a different port priority than the default

on the port FastEthernet4/1

1-2

The following ports have recieve flow control disabled:

Fa9/35, Fa9/45

The following inline power ports have power-deny/faulty status:

Gi7/1, Gi7/2

The following ports have negotiated to half-duplex:

Fa9/45

The following vlans have a duplex mismatch:

Fas 9/45

The following interafaces have a native vlan mismatch:

interface (native vlan - neighbor vlan)

 Fas 9/45 (1 - 64)

The value for Community-Access on read-only operations for SNMP is the same

as default. Please verify that this is the best value from a security point

of view.

The value for Community-Access on write-only operations for SNMP is the same

as default. Please verify that this is the best value from a security point

of view.

The value for Community-Access on read-write operations for SNMP is the same

as default. Please verify that this is the best value from a security point

of view.

Please check the status of the following modules:

8,9

Module 2 had a MINOR_ERROR.

The Module 2 failed the following tests:

TestIngressSpan

The following ports from Module2 failed test1:

1,2,4,48

show dot1q-tunnel

To display a list of 802.1Q tunnel-enabled ports, use the show dot1q-tunnel command.

show dot1q-tunnel [{interface interface interface-number}]

Syntax Description


interface interface	(Optional) Specifies the interface type; possible valid values are ethernet, fastethernet, gigabitethernet, tengigabitethernet, and port-channel.
interface-number	Interface number; see the "Usage Guidelines" section for valid values.

Command Default

This command has no default settings.

Command Default

EXEC

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

If you do not enter any keywords, the 802.1Q tunnel ports for all interfaces are displayed.

The interface-number argument designates the module and port number for the ethernet, fastethernet, gigabitethernet, and tengigabitethernet keywords. Valid values depend on the chassis and module that are used. For example, if you have a 48-port 10/100BASE-T Ethernet module that is installed in a 13-slot chassis, valid values for the slot number are from 1 to 13 and valid values for the port number are from 1 to 48.

The interface-number argument designates the port-channel number for the port-channel keyword; valid values are from 1 to 282. The values from 257 to 282 are supported on the CSM and the FWSM only.

Examples

This example indicates that the port is up and has one 802.1Q tunnel that is configured on it:

Router# show dot1q-tunnel interface port-channel 10

Interface

---------

Po10

Related Commands


Command	Description
switchport mode	Sets the interface type.
vlan dot1q tag native	Enables 802.1Q tagging for all VLANs in a trunk.

show dot1x

To display the 802.1X information, use the show dot1x command.

show dot1x {interface interface interface-number}

show dot1x {all | brief | summary | {statistics {interface interface interface-number}}}

Syntax Description


interface interface	Displays the 802.1X information for the interface type; possible valid values are ethernet, fastethernet, gigabitethernet, and tengigabitethernet.
interface-number	Interface number; see the "Usage Guidelines" section for valid values.
all	Displays the 802.1X information for all interfaces.
brief	Displays information about the 802.1X status for all interfaces.
summary	Displays information about the 802.1X summary for the whole system.
statistics	Displays information about the 802.1X port; see the "Usage Guidelines" section for information.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

When entering the show dot1x statistics command, you must enter interface interface interface-number for the command to perform correctly.

If you disable 802.1X globally, the output of the show dot1x brief command displays nothing and the show dot1x summary command output displays 0 in all fields.

The interface-number argument designates the module and port number for the ethernet, fastethernet, gigabitethernet, and tengigabitetherne keywords. Valid values depend on the chassis and module that are used. For example, if you have a 48-port 10/100BASE-T Ethernet module that is installed in a 13-slot chassis, valid values for the slot number are from 1 to 13 and valid values for the port number are from 1 to 48.

Examples

This example shows how to display the 802.1X information for a specific interface:

Router# show dot1x interface fastethernet 5/1

Default Dot1x Configuration Exists for this interface FastEthernet5/1

AuthSM State      = FORCE AUTHORIZED

BendSM State      = IDLE

PortStatus        = AUTHORIZED

MaxReq            = 2

MultiHosts        = Disabled

PortControl       = Force Authorized

QuietPeriod       = 60 Seconds

Re-authentication = Disabled

ReAuthPeriod      = 3600 Seconds

ServerTimeout     = 30 Seconds

SuppTimeout       = 30 Seconds

TxPeriod          = 30 Seconds

Router#

This example shows how to display the 802.1X information for all interfaces:

Router# show dot1x all

Dot1x Info for interface FastEthernet3/2  
----------------------------------------------------  
AuthSM State = FORCE UNAUTHORIZED  
BendSM State = IDLE  
PortStatus = UNAUTHORIZED  
MaxReq = 2  
MultiHosts = Disabled  
Port Control = Force UnAuthorized  
QuietPeriod = 60 Seconds  
Re-authentication = Disabled  
ReAuthPeriod = 3600 Seconds  
ServerTimeout = 30 Seconds  
SuppTimeout = 30 Seconds  
TxPeriod = 30 Seconds

Dot1x Info for interface FastEthernet3/12  
----------------------------------------------------  
AuthSM State = Unknown State  
BendSM State = Unknown State  
PortStatus = UNKNOWN  
MaxReq = 2  
MultiHosts = Disabled  
Port Control = Auto  
QuietPeriod = 60 Seconds  
Re-authentication = Disabled  
ReAuthPeriod = 3600 Seconds  
ServerTimeout = 30 Seconds  
SuppTimeout = 30 Seconds  
TxPeriod = 30 Seconds

Guest-Vlan = 91

Router#

This example shows how to display the 802.1X statistics for a port:

Router# show dot1x statistics interface fastethernet3/1  
PortStatistics Parameters for Dot1x  
--------------------------------------------  
TxReqId = 0 TxReq = 0 TxTotal = 0  
RxStart = 0 RxLogoff = 0 RxRespId = 0 RxResp = 0  
RxInvalid = 0 RxLenErr = 0 RxTotal= 0  
RxVersion = 0 LastRxSrcMac 0000.0000.0000

Router#

This example shows how to display a summary of 802.1X information for the whole system:

Router# show dot1x summary

Total number of dot1x enabled ports:             336

Total number of FORCE_UNAUTHORIZED dot1x ports:  0

Total number of authorized dot1x enabled ports:  254

Total number of dot1x ports in single host mode: 336

Total number of dot1x ports in multi host mode:  0

Total number of dot1x authenticated supplicants:          254

Total number of supplicants in AUTH_DISCONNECTED state:   0

Total number of supplicants in AUTH_CONNECTING state:     0

Total number of supplicants in AUTH_AUTHENTICATING state: 0

Total number of supplicants in AUTH_HELD state:           0

Router#

This example shows how to display the status of all 802.1X-enabled ports:

Router# show dot1x brief

RV - Radius returned VLAN

Port      Supplicant MAC  AuthSM State        BendSM State   Port Status   RV

----      --------------  ------------        ------------   -----------   ----

Fa4/1     0000.0000.0000  N/A                 N/A            N/A            -

Fa4/2     0000.0000.0000  N/A                 N/A            N/A            -

Fa4/3     0000.0000.0000  N/A                 N/A            N/A            -

Fa4/4     0000.0000.0000  N/A                 N/A            N/A            -

Fa4/5     0000.0000.0000  N/A                 N/A            N/A            -

Fa4/6     0000.0000.0000  N/A                 N/A            N/A            -

Fa4/7     0000.0000.0000  N/A                 N/A            N/A            -

. Output truncated

Fa4/35    00fe.ed00.01ba  AUTHENTICATED       IDLE           AUTHORIZED    101

Fa4/36    00fe.ed00.01b8  AUTHENTICATED       IDLE           AUTHORIZED    101

Fa4/37    00fe.ed00.01e6  AUTHENTICATED       IDLE           AUTHORIZED    101

Fa4/38    00fe.ed00.01e4  AUTHENTICATED       IDLE           AUTHORIZED    101

Fa4/39    00fe.ed00.01e2  AUTHENTICATED       IDLE           AUTHORIZED    101

Fa4/40    00fe.ed00.01e0  AUTHENTICATED       IDLE           AUTHORIZED    101

Fa4/41    00fe.ed00.01de  AUTHENTICATED       IDLE           AUTHORIZED    101

Fa4/42    00fe.ed00.01dc  AUTHENTICATED       IDLE           AUTHORIZED    101

Router#

show dss log

To display the invalidation routes for the DSS range on the NetFlow table, use the show dss log command.

show dss log {ip | ipv6}

Syntax Description


ip	Displays the range-invalidation profile for the DSS IP.
ipv6	Displays the range-invalidation profile for the DSS IPv6.

Command Default

This command has no default settings.

Command Default

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

Whenever an IPv6 entry is deleted from the routing table, a message is sent to the switch processor to remove the entries that are associated to that network. Several IPv6 prefixes are collapsed to the less specific one if too many invalidations occur in a short period of time.

Examples

This example shows how to display the range-invalidation profile for the DSS IP:

Router# show dss log ip

22:50:18.551  prefix 172.20.52.18 mask 172.20.52.18

22:50:20.059  prefix 127.0.0.0 mask 255.0.0.0

22:51:48.767  prefix 172.20.52.18 mask 172.20.52.18

22:51:52.651  prefix 0.0.0.0 mask 0.0.0.0

22:53:02.651  prefix 0.0.0.0 mask 0.0.0.0

22:53:19.651  prefix 0.0.0.0 mask 0.0.0.0

Router#

show environment alarm

To display the information about the environmental alarm, use the show environment alarm command.

show environment alarm [{status | threshold} [frutype]]

Syntax Description


status	(Optional) Displays the operational FRU status.
threshold	(Optional) Displays the preprogrammed alarm thresholds.
frutype	(Optional) Alarm type; valid values are all, backplane, clock number, earl slot, fan-tray, module slot, rp slot, power-supply number, supervisor slot, and vtt number. See the "Usage Guidelines" section for a list of valid values for number and slot.

Command Default

If you do not enter a frutype, all the information about the environmental alarm status is displayed.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

Valid values for the frutype are as follows:

•clock number—1 and 2.

•earl slot—See the "Usage Guidelines" section for valid values.

•module slot—See the "Usage Guidelines" section for valid values.

•rp slot—See the "Usage Guidelines" section for valid values.

•power-supply number—1 and 2.

•supervisor slot—See the "Usage Guidelines" section for valid values.

•vtt number—1 to 3.

The slot argument designates the module and port number. Valid values for slot depend on the chassis and module that are used. For example, if you have a 48-port 10/100BASE-T Ethernet module that is installed in a 13-slot chassis, valid values for the slot number are from 1 to 13 and valid values for the port number are from 1 to 48.

Examples

This example shows how to display all the information about the status of the environmental alarm:

Router> show environment alarm threshold

environmental alarm thresholds:

power-supply 1 fan-fail: OK

  threshold #1 for power-supply 1 fan-fail:

    (sensor value != 0) is system minor alarm

power-supply 1 power-output-fail: OK

  threshold #1 for power-supply 1 power-output-fail:

    (sensor value != 0) is system minor alarm

fantray fan operation sensor: OK

  threshold #1 for fantray fan operation sensor:

    (sensor value != 0) is system minor alarm

operating clock count: 2

  threshold #1 for operating clock count:

    (sensor value < 2) is system minor alarm

  threshold #2 for operating clock count:

    (sensor value < 1) is system major alarm

operating VTT count: 3

  threshold #1 for operating VTT count:

    (sensor value < 3) is system minor alarm

  threshold #2 for operating VTT count:

    (sensor value < 2) is system major alarm

VTT 1 OK: OK

  threshold #1 for VTT 1 OK:

    (sensor value != 0) is system minor alarm

VTT 2 OK: OK

  threshold #1 for VTT 2 OK:

    (sensor value != 0) is system minor alarm

VTT 3 OK: OK

  threshold #1 for VTT 3 OK:

    (sensor value != 0) is system minor alarm

clock 1 OK: OK

  threshold #1 for clock 1 OK:

    (sensor value != 0) is system minor alarm

clock 2 OK: OK

  threshold #1 for clock 2 OK:

    (sensor value != 0) is system minor alarm

module 1 power-output-fail: OK

  threshold #1 for module 1 power-output-fail:

    (sensor value != 0) is system major alarm

module 1 outlet temperature: 21C

  threshold #1 for module 1 outlet temperature:

    (sensor value > 60) is system minor alarm

  threshold #2 for module 1 outlet temperature:

    (sensor value > 70) is system major alarm

module 1 inlet temperature: 25C

  threshold #1 for module 1 inlet temperature:

    (sensor value > 60) is system minor alarm

  threshold #2 for module 1 inlet temperature:

    (sensor value > 70) is system major alarm

module 1 device-1 temperature: 30C

  threshold #1 for module 1 device-1 temperature:

    (sensor value > 60) is system minor alarm

  threshold #2 for module 1 device-1 temperature:

    (sensor value > 70) is system major alarm

module 1 device-2 temperature: 29C

  threshold #1 for module 1 device-2 temperature:

    (sensor value > 60) is system minor alarm

  threshold #2 for module 1 device-2 temperature:

    (sensor value > 70) is system major alarm

module 5 power-output-fail: OK

  threshold #1 for module 5 power-output-fail:

    (sensor value != 0) is system major alarm

module 5 outlet temperature: 26C

  threshold #1 for module 5 outlet temperature:

    (sensor value > 60) is system minor alarm

  threshold #2 for module 5 outlet temperature:

    (sensor value > 75) is system major alarm

module 5 inlet temperature: 23C

  threshold #1 for module 5 inlet temperature:

    (sensor value > 50) is system minor alarm

  threshold #2 for module 5 inlet temperature:

    (sensor value > 65) is system major alarm

EARL 1 outlet temperature: N/O

  threshold #1 for EARL 1 outlet temperature:

    (sensor value > 60) is system minor alarm

  threshold #2 for EARL 1 outlet temperature:

    (sensor value > 75) is system major alarm

EARL 1 inlet temperature: N/O

  threshold #1 for EARL 1 inlet temperature:

    (sensor value > 50) is system minor alarm

  threshold #2 for EARL 1 inlet temperature:

    (sensor value > 65) is system major alarm

Router>

Related Commands


Command	Description
show environment status	Displays the information about the operational FRU status.
show environment temperature	Displays the current temperature readings.

show environment cooling

To display the information about the cooling parameter, use the show environment cooling command.

show environment cooling

Syntax Description

This command has no arguments or keywords.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Examples

This example shows how to display the information about the cooling parameter:

Router# show environment cooling

fan-tray 1:

  fan-tray 1 fan-fail: failed

fan-tray 2:

  fan 2 type: FAN-MOD-9

  fan-tray 2 fan-fail: OK

chassis cooling capacity: 690 cfm

ambient temperature: 55C

chassis per slot cooling capacity: 75 cfm

  module 1 cooling requirement: 70 cfm

  module 2 cooling requirement: 70 cfm

  module 5 cooling requirement: 30 cfm

  module 6 cooling requirement: 70 cfm

  module 8 cooling requirement: 70 cfm

  module 9 cooling requirement: 30 cfm

Router#

Related Commands


Command	Description
hw-module fan-tray version	Sets the version (high or low power) type of the fan.

show environment status

To display the information about the operational FRU status, use the show environment status command.

show environment status [frutype]

Syntax Description


frutype	(Optional) FRU type; see the "Usage Guidelines" section for a list of valid values.

Command Default

If you do not enter a frutype, all FRU status information is displayed.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

Valid values for the frutype are as follows:

•all—No arguments.

•backplane—No arguments.

•clock number—1 and 2.

•earl slot—See the "Usage Guidelines" section for valid values.

•fan-tray—No arguments.

•module slot—See the "Usage Guidelines" section for valid values.

•power-supply number—1 and 2.

•rp slot—See the "Usage Guidelines" section for valid values.

•supervisor slot—See the "Usage Guidelines" section for valid values.

•vtt number—1 to 3.

Examples

This example shows how to display the information about the environmental status:

Router> show environment status

backplane:

  operating clock count: 2

  operating VTT count: 3

fan-tray:

  fantray fan operation sensor: OK

VTT 1:

  VTT 1 OK: OK

VTT 2:

  VTT 2 OK: OK

VTT 3:

  VTT 3 OK: OK

clock 1:

  clock 1 OK: OK, clock 1 clock-inuse: not-in-use

clock 2:

  clock 2 OK: OK, clock 2 clock-inuse: in-use

power-supply 1:

  power-supply 1 fan-fail: OK

  power-supply 1 power-output-fail: OK

module 1:

  module 1 power-output-fail: OK

  module 1 outlet temperature: 21C

  module 1 inlet temperature: 25C

  module 1 device-1 temperature: 30C

  module 1 device-2 temperature: 29C

  EARL 1 outlet temperature: N/O

  EARL 1 inlet temperature: N/O

module 5:

  module 5 power-output-fail: OK

  module 5 outlet temperature: 26C

  module 5 inlet temperature: 23C

  module 5 device-1 temperature: 26C

  module 5 device-2 temperature: 27C

Router>

This example shows how to display the information about the high-capacity power supplies:

Router# show environment status power-supply 2

power-supply 2:

  power-supply 2 fan-fail: OK

  power-supply 2 power-input 1: none

  power-supply 2 power-input 2: AC low

  power-supply 2 power-input 3: AC high

  power-supply 2 power-output: low (mode 1)

  power-supply 2 power-output-fail: OK

Table 2-35 describes the fields that are shown in the example.

Table 2-35 show environment status Command Output Fields
Field	Description
operating clock count	Physical clock count.
operating VTT count	Physical VTT count.
fan tray fan operation sensor	System fan tray failure status. The failure of the system fan tray is indicated as a minor alarm.
VTT 1, VTT2, and VTT3	Status of the chassis backplane power monitors that are located on the rear of the chassis under the rear cover. Operation of at least two VTTs is required for the system to function properly. A minor system alarm is signaled when one of the three VTTs fails. A major alarm is signaled when two or more VTTs fail and the supervisor engine is accessible through the console port.
clock # clock-inuse	Clock status. Failure of either clock is considered to be a minor alarm.
power-supply # fan-fail	Fan failure. Fan failures on either or both (if any) power supplies are considered minor alarms.
power-input-fail	Power input failure status (none, AC high, AC low).
power-output-fail	Power output failure status (high, low).
outlet temperature	Exhaust temperature value.
inlet temperature	Intake temperature value.
device-1 and device-2 temperature	Two devices that measure the internal temperature on each indicated module. The temperature shown indicates the temperature that the device is recording. The devices are not placed at an inlet or an exit but are additional reference points.

Related Commands


Command	Description
show environment alarm	Displays the information about the environmental alarm.
show environment temperature	Displays the current temperature readings.

show environment temperature

To display the current temperature readings, use the show environment temperature command.

show environment temperature [frutype]

Syntax Description


frutype	(Optional) FRU type; see the "Usage Guidelines" section for a list of valid values.

Command Default

If you do not enter a frutype, the module and EARL temperature readings are displayed.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

Valid values for the frutype are as follows:

•earl slot—See the "Usage Guidelines" section for valid values.

•module slot—See the "Usage Guidelines" section for valid values.

•rp slot—See the "Usage Guidelines" section for valid values.

•vtt number—1 to 3.

•clock number—1 and 2.

The show environment temperature module command output includes the updated information after an SCP response is received.

In the output display, the following applies:

•N/O means not operational—The sensor is broken, returning impossible values.

•N/A means not available—The sensor value is presently not available; try again later.

•VTT 1, 2, and 3 refer to the power monitors that are located on the chassis backplane under the rear cover.

Examples

This example shows how to display the temperature information for a specific module:

Router> show environment temperature module 5

  module 5 outlet temperature: 34C

  module 5 inlet temperature: 27C

  module 5 device-1 temperature: 42C

  module 5 device-2 temperature: 41C

  module 5 asic-1 (SSO-1) temp: 29C

  module 5 asic-2 (SSO-2) temp: 29C

  module 5 asic-3 (SSO-3) temp: 29C

  module 5 asic-4 (SSO-4) temp: 28C

  module 5 asic-5 (SSA-1) temp: 29C

  module 5 asic-6 (HYPERION-1) temp: 29C

Router>

This example shows how to display the temperature readings for all modules:

Router> show environment temperature

  VTT 1 outlet temperature: 25C

  VTT 2 outlet temperature: 24C

  VTT 3 outlet temperature: 28C

  module 1 outlet temperature: 24C

  module 1 device-2 temperature: 29C

  RP 1 outlet temperature: 25C

  RP 1 inlet temperature: 29C

  EARL 1 outlet temperature: 25C

  EARL 1 inlet temperature: 22C

  module 5 outlet temperature: 27C

  module 5 inlet temperature: 22C

Router#

Table 2-36 describes the fields that are shown in the example.

Table 2-36 show environment temperature Command Output Fields
Field	Description
outlet temperature	Exhaust temperature value.
inlet temperature	Intake temperature value.
device-1 and device-2 temperature	Two devices that measure the internal temperature on the indicated module. The temperature shown indicates the temperature that the device is recording. The devices are not placed at an inlet or an exit but are additional reference points.

Related Commands


Command	Description
show environment alarm	Displays the information about the environmental alarm.
show environment status	Displays the information about the operational FRU status.

show eobc

To display the information about the EOBC interface, use the show eobc command.

show eobc

Syntax Description

This command has no keywords or arguments.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Examples

This example shows how to display the information about the EOBC interface:

Router> show eobc

EOBC0/0 is up, line protocol is up

  Hardware is DEC21143, address is 0000.2100.0000 (bia 0000.2100.0000)

  MTU 0 bytes, BW 100000 Kbit, DLY 100 usec,

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ARPA, loopback not set

  Keepalive not set

  Unknown duplex, Unknown Speed, MII

  ARP type: ARPA, ARP Timeout 04:00:00

  Last input never, output 00:00:00, output hang never

  Last clearing of "show interface" counters never

  Queueing strategy: fifo

  Output queue 0/40, 0 drops; input queue 25/2147483647, 0 drops

  5 minute input rate 0 bits/sec, 0 packets/sec

  5 minute output rate 0 bits/sec, 0 packets/sec

     172196 packets input, 11912131 bytes

     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

     0 watchdog, 0 multicast

     0 input packets with dribble condition detected

     172144 packets output, 11363476 bytes, 0 underruns

     0 output errors, 0 collisions, 1 interface resets

     0 babbles, 0 late collision, 0 deferred

     0 lost carrier, 0 no carrier

     0 output buffer failures, 0 output buffers swapped out

Interface EOBC0/0

Hardware is DEC21143

 dec21140_ds=0x618FB938, registers=0x3C018000, ib=0x38A9180

 rx ring entries=128, tx ring entries=256, af setup failed=0

 rxring=0x38A9280, rxr shadow=0x618FBB20, rx_head=28, rx_tail=0

 txring=0x38A9AC0, txr shadow=0x618FBD4C, tx_head=72, tx_tail=72, tx_count=0

 PHY link up

 CSR0=0xF8024882, CSR1=0xFFFFFFFF, CSR2=0xFFFFFFFF, CSR3=0x38A9280

 CSR4=0x38A9AC0, CSR5=0xF0660000, CSR6=0x320CA002, CSR7=0xF3FFA261

 CSR8=0xE0000000, CSR9=0xFFFDC3FF, CSR10=0xFFFFFFFF, CSR11=0x0

 CSR12=0xC6, CSR13=0xFFFF0000, CSR14=0xFFFFFFFF, CSR15=0x8FF80000

 DEC21143 PCI registers:

  bus_no=0, device_no=6

  CFID=0x00191011, CFCS=0x02800006, CFRV=0x02000041, CFLT=0x0000FF00

  CBIO=0x20000801, CBMA=0x48018000, CFIT=0x28140120, CFDD=0x00000400

 MII registers:

  Register 0x00:   FFFF  FFFF  FFFF  FFFF  FFFF  FFFF  FFFF  FFFF

  Register 0x08:   FFFF  FFFF  FFFF  FFFF  FFFF  FFFF  FFFF  FFFF

  Register 0x10:   FFFF  FFFF  FFFF  FFFF  FFFF  FFFF  FFFF  FFFF

  Register 0x18:   FFFF  FFFF  FFFF  FFFF  FFFF  FFFF  FFFF  FFFF

throttled=0, enabled=0, disabled=0

 rx_fifo_overflow=0, rx_no_enp=0, rx_discard=0

 tx_underrun_err=0, tx_jabber_timeout=0, tx_carrier_loss=0

 tx_no_carrier=0, tx_late_collision=0, tx_excess_coll=0

 tx_collision_cnt=0, tx_deferred=0, fatal_tx_err=0, tbl_overflow=0

 HW addr filter: 0x38D2EE0, ISL Disabled

  Entry= 0:  Addr=0000.0000.0000

  Entry= 1:  Addr=0000.0000.0000

  Entry= 2:  Addr=0000.0000.0000

  Entry= 3:  Addr=0000.0000.0000

  Entry= 4:  Addr=0000.0000.0000

  Entry= 5:  Addr=0000.0000.0000

  Entry= 6:  Addr=0000.0000.0000

  Entry= 7:  Addr=0000.0000.0000

  Entry= 8:  Addr=0000.0000.0000

  Entry= 9:  Addr=0000.0000.0000

  Entry=10:  Addr=0000.0000.0000

  Entry=11:  Addr=0000.0000.0000

  Entry=12:  Addr=0000.0000.0000

  Entry=13:  Addr=0000.0000.0000

  Entry=14:  Addr=0000.0000.0000

  Entry=15:  Addr=0000.2100.0000

Router>

This example shows how to display the information about the EOBC interface but excludes lines that contain the word output:

Router> show eobc | exclude output

EOBC0/0 is up, line protocol is up

  Hardware is DEC21143, address is 0000.2100.0000 (bia 0000.2100.0000)

  MTU 0 bytes, BW 100000 Kbit, DLY 100 usec,

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ARPA, loopback not set

  Keepalive not set

  Unknown duplex, Unknown Speed, MII

  ARP type: ARPA, ARP Timeout 04:00:00

  Last clearing of "show interface" counters never

  Queueing strategy: fifo

  Output queue 0/40, 0 drops; input queue 25/2147483647, 0 drops

  5 minute input rate 0 bits/sec, 0 packets/sec

     175919 packets input, 12196443 bytes

     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

     0 watchdog, 0 multicast

     0 input packets with dribble condition detected

     0 babbles, 0 late collision, 0 deferred

     0 lost carrier, 0 no carrier

Interface EOBC0/0

Hardware is DEC21143

 dec21140_ds=0x618FB938, registers=0x3C018000, ib=0x38A9180

 rx ring entries=128, tx ring entries=256, af setup failed=0

 rxring=0x38A9280, rxr shadow=0x618FBB20, rx_head=7, rx_tail=0

 txring=0x38A9AC0, txr shadow=0x618FBD4C, tx_head=209, tx_tail=209, tx_count=0

 PHY link up

 CSR0=0xF8024882, CSR1=0xFFFFFFFF, CSR2=0xFFFFFFFF, CSR3=0x38A9280

 CSR4=0x38A9AC0, CSR5=0xF0660000, CSR6=0x320CA002, CSR7=0xF3FFA261

 CSR8=0xE0000000, CSR9=0xFFFDC3FF, CSR10=0xFFFFFFFF, CSR11=0x0

 CSR12=0xC6, CSR13=0xFFFF0000, CSR14=0xFFFFFFFF, CSR15=0x8FF80000

 DEC21143 PCI registers:

  bus_no=0, device_no=6

  CFID=0x00191011, CFCS=0x02800006, CFRV=0x02000041, CFLT=0x0000FF00

  CBIO=0x20000801, CBMA=0x48018000, CFIT=0x28140120, CFDD=0x00000400

 MII registers:

  Register 0x00:   FFFF  FFFF  FFFF  FFFF  FFFF  FFFF  FFFF  FFFF

  Register 0x08:   FFFF  FFFF  FFFF  FFFF  FFFF  FFFF  FFFF  FFFF

  Register 0x10:   FFFF  FFFF  FFFF  FFFF  FFFF  FFFF  FFFF  FFFF

  Register 0x18:   FFFF  FFFF  FFFF  FFFF  FFFF  FFFF  FFFF  FFFF

 throttled=0, enabled=0, disabled=0

 rx_fifo_overflow=0, rx_no_enp=0, rx_discard=0

 tx_underrun_err=0, tx_jabber_timeout=0, tx_carrier_loss=0

 tx_no_carrier=0, tx_late_collision=0, tx_excess_coll=0

 tx_collision_cnt=0, tx_deferred=0, fatal_tx_err=0, tbl_overflow=0

 HW addr filter: 0x38D2EE0, ISL Disabled

  Entry= 0:  Addr=0000.0000.0000

  Entry= 1:  Addr=0000.0000.0000

  Entry= 2:  Addr=0000.0000.0000

  Entry= 3:  Addr=0000.0000.0000

  Entry= 4:  Addr=0000.0000.0000

  Entry= 5:  Addr=0000.0000.0000

  Entry= 6:  Addr=0000.0000.0000

  Entry= 7:  Addr=0000.0000.0000

  Entry= 8:  Addr=0000.0000.0000

  Entry= 9:  Addr=0000.0000.0000

  Entry=10:  Addr=0000.0000.0000

  Entry=11:  Addr=0000.0000.0000

  Entry=12:  Addr=0000.0000.0000

  Entry=13:  Addr=0000.0000.0000

  Entry=14:  Addr=0000.0000.0000

  Entry=15:  Addr=0000.2100.0000

Router>

show erm statistics

To display the FIB TCAM exception status for IPv4, IPv6, and MPLS protocols, use the show erm statistics command.

show erm statistics

Syntax Description

This command has no keywords or arguments.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

The IPv4, IPv6, and MPLS exception state displays FALSE when the protocol is not under the exception or displays TRUE when the protocol is under the exception.

Examples

This example shows how to display the FIB TCAM exception status for IPv4, IPv6, and MPLS protocols:

Router> show erm statistics

#IPv4 excep notified     = 0

#IPv6 excep notified     = 0

#MPLS excep notified     = 0

#IPv4 reloads done       = 0

#IPv6 reloads done       = 0

#MPLS reloads done       = 0

Current IPv4 excep state = FALSE

Current IPv6 excep state = FALSE

Current MPLS excep state = FALSE

#Timer expired           = 0

#of erm msgs             = 1

Router>

Related Commands


Command	Description
mls erm priority	Assigns the priorities to define an order in which protocols attempt to recover from the exception status.

show errdisable detect

To display the error-disable detection status, use the show errdisable detect command.

show errdisable detect

Syntax Description

This command has no keywords or arguments.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Examples

This example shows how to display the error-disable detection status:

Router# show errdisable detect

ErrDisable Reason    Detection status

-----------------    ----------------

udld                 Enabled

bpduguard            Enabled

rootguard            Enabled

packet-buffer-err    Enabled

pagp-flap            Enabled

dtp-flap             Enabled

link-flap            Enabled

Router#

Related Commands


Command	Description
errdisable detect cause	Enables the error-disable detection.

show errdisable flap-value

To display the flap values for error-disable detection, use the show errdisable flap-value command.

show errdisable flap-value

Syntax Description

This command has no keywords or arguments.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Examples

This example shows how to display the flap values for error-disable detection:

Router# show errdisable flap-value

ErrDisable Reason    Flaps    Time (sec)

-----------------    ------   ----------

pagp-flap              3       30

dtp-flap               3       30

link-flap              5       10

Router#Router#

Related Commands


Command	Description
errdisable detect cause	Enables the error-disable detection.

show errdisable recovery

To display the information about the error-disable recovery timer, use the show errdisable recovery command.

show errdisable recovery

Syntax Description

This command has no keywords or arguments.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Examples

This example shows how to display the information about the error-disable recovery timer:

Router# show errdisable recovery

ErrDisable Reason    Timer Status

-----------------    --------------

udld                 Enabled

bpduguard            Enabled

rootguard            Enabled

pagp-flap            Enabled

dtp-flap             Enabled

link-flap            Enabled

Timer interval:300 seconds

Interfaces that will be enabled at the next timeout:

Interface    Errdisable reason    Time left(sec)

---------    -----------------    --------------

Fa9/4           link-flap             279

Related Commands


Command	Description
errdisable recovery	Configures the recovery mechanism variables.
show interfaces status	Displays the interface status or a list of interfaces in an error-disabled state on LAN ports only.

show etherchannel

To display the EtherChannel information for a channel, use the show etherchannel command.

show etherchannel [channel-group] {port-channel | brief | detail | summary | port | load-balance | protocol}

Syntax Description


channel-group	(Optional) Number of the channel group; valid values are a maximum of 64 values from 1 to 282.
port-channel	Displays the port-channel information.
brief	Displays a summary of EtherChannel information.
detail	Displays the detailed EtherChannel information.
summary	Displays a one-line summary per channel group.
port	Displays the EtherChannel port information.
load-balance	Displays load-balance information.
protocol	Displays the enabled protocol.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

If you do not specify a channel-group, all channel groups are displayed.

The channel-group values that are from 257 to 282 are supported on the CSM and the FWSM only.

In the output, the Passive port list field is displayed for Layer 3 port channels only. This field means that the physical interface, which is still not up, is configured to be in the channel group (and indirectly is the only port channel in the channel group).

In the show etherchannel protocol output, if the interface is configured as part of the channel in mode ON, the command displays Protocol: - (Mode ON).

In the output of the show etherchannel summary command, the following guidelines apply:

•In the column that displays the protocol that is used for the channel, if the channel mode is ON, a hyphen (-) is displayed.

•Multiple aggregators are supported for LACP. For example, if two different bundles are created, Po1 indicates the primary aggregator, and Po1A and Po1B indicate the secondary aggregators.

In the output of the show etherchannel load-balance command, the following guidelines apply:

•For EtherChannel load balancing of IPv6 traffic, if the traffic is bridged onto an EtherChannel (for example, it is a Layer 2 channel and traffic in the same VLAN is bridged across it), the traffic is always load balanced by the IPv6 addresses or either src, dest, or src-dest, depending on the configuration. For this reason, the switch ignores the MAC/IP/ports for bridged IPv6 traffic. If you configure src-dst-mac, the src-dst-ip(v6) address is used. If you configure src-mac, the src-ip(v6) address is used.

•IPv6 traffic that is routed over a Layer 2 or a Layer 3 channel is load balanced based on MAC addresses or IPv6 addresses, depending on the configuration. The MAC/IP and the src/dst/src-dst are supported, but load balancing that is based on Layer 4 ports is not supported. If you use the port keyword, the IPv6 addresses, src, dst, or src-dst are used.

Examples

This example shows how to display the port-channel information for a specific group:

Router# show etherchannel 12 port-channel

Group: 12

----------

                Port-channels in the group:

                ----------------------

Port-channel: Po1

------------

Age of the Port-channel   = 143h:01m:12s

Logical slot/port   = 14/1           Number of ports = 2

GC                  = -              HotStandBy port = null

Port state          = Port-channel Ag-Inuse

Protocol            = LACP

Ports in the Port-channel:

Index   Load   Port    EC state

------+------+------+------------

  0     55     Fa4/1   active

  1     AA     Fa4/2   active

Time since last port bundled:    16h:28m:58s    Fa4/1

Time since last port Un-bundled: 16h:29m:00s    Fa4/4

Router#

This example shows how to display the load-balancing information:

Router# show etherchannel load-balance

EtherChannel Load-Balancing Configuration:

        dst-mac

        mpls label-ip

EtherChannel Load-Balancing Addresses Used Per-Protocol:

Non-IP: Destination MAC address

  IPv4: Destination MAC address

  IPv6: Destination MAC address (routed packets)

        Destination IP address (bridged packets)

  MPLS: Label or IP

Router#

This example shows how to display a summary of information for a specific group:

Router# show etherchannel 1 brief

Group: 1

----------

Group state = L2

Ports: 4   Maxports = 8

Port-channels: 1 Max Port-channels = 1

Protocol: LACP

Router#

This example shows how to display the detailed information for a specific group:

Router# show etherchannel 12 detail

Group state = L2

Ports: 1   Maxports = 8

Port-channels: 1 Max Port-channels = 1

Protocol:   PAgP

                Ports in the group:

                -------------------

Port: Fa5/2

------------

Port state    = Down Not-in-Bndl

Channel group = 12          Mode = Desirable-Sl     Gcchange = 0

Port-channel  = null        GC   = 0x00000000          Pseudo port-channel = Po1

Port index    = 0           Load = 0x00        Protocol =   PAgP

Flags:  S - Device is sending Slow LACPDUs F - Device is sending fast LACPDUs

        A - Device is in active mode       P - Device is in passive mode

Local information:

                            LACP Port    Admin     Oper    Port     Port

Port      Flags   State     Priority      Key      Key     Number   State

Fa4/1     SA      bndl      32768         100      100     0xc1     0x75

Partner's information:

         Partner                Partner               Partner

Port     System ID              Port Number    Age    Flags

Fa4/1    8000,00b0.c23e.d861    0x81	           14s    SP

         LACP Partner    Partner     Partner

         Port Priority   Oper Key    Port State

         32768	           128         0x81

Age of the port in the current state: 16h:27m:42s

                Port-channels in the group:

                ----------------------

Port-channel: Po12

------------

Age of the Port-channel   = 04d:02h:52m:26s

Logical slot/port   = 14/1          Number of ports = 0

GC                  = 0x00000000      HotStandBy port = null

Port state          = Port-channel Ag-Not-Inuse

Protocol            =   PAgP

Router#

This example shows how to display a one-line summary per channel group:

Router# show etherchannel summary

Flags:  D - down        P - in port-channel

        I - stand-alone s - suspended

        H - Hot-standby (LACP only)

        R - Layer3      S - Layer2

        U - in use      f - failed to allocate aggregator

Number of channel-groups in use: 2

Number of aggregators:           2

Group  Port-channel  Protocol    Ports

------+-------------+-----------+-----------------------------------------------

12     Po12(SD)        PAgP      Fa5/2(D)

24     Po24(RD)         -

Router#

This example shows how to display the information about the EtherChannel port for a specific group:

Router# show etherchannel 1 port

                Channel-group listing:

                -----------------------

Group: 1

----------

                Ports in the group:

                -------------------

Port: Fa5/4

------------

Port state    = EC-Enbld Down Not-in-Bndl Usr-Config

Channel group = 1           Mode = Desirable     Gcchange = 0

Port-channel  = null        GC   = 0x00000000    Psudo-agport = Po1

Port index    = 0           Load = 0x00        Protocol =   LACP

Flags:  S - Device is sending Slow LACPDUs F - Device is sending fast LACPDUs

        A - Device is in active mode       P - Device is in passive mode

Local information:

                            LACP Port    Admin     Oper    Port     Port

Port      Flags   State     Priority      Key      Key     Number   State

Fa5/4     SA      bndl      32768         100      100     0xc1     0x75

Partner's information:

         Partner                Partner               Partner

Port     System ID              Port Number    Age    Flags

Fa5/4    8000,00b0.c23e.d861    0x81	           14s    SP

         LACP Partner    Partner     Partner

         Port Priority   Oper Key    Port State

         32768	           128         0x81

Age of the port in the current state: 04d:02h:57m:38s

Router#

This example shows how to display the protocol that was enabled:

Router# show etherchannel protocol

                Channel-group listing:

                -----------------------

Group: 12

----------

Protocol:  PAgP

Group: 24

----------

Protocol:   -  (Mode ON)

Router#

Related Commands


Command	Description
channel-group	Assigns and configures an EtherChannel interface to an EtherChannel group.
channel-protocol	Sets the protocol that is used on an interface to manage channeling.
interface port-channel	Creates a port-channel virtual interface and enters interface configuration mode.

show fm features

To display the information about the feature manager, use the show fm features command.

show fm features

Syntax Description

This command has no keywords or arguments.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Examples

This example shows how to display the information about the feature manager:

Router> show fm features

Designated PISA:1 Non-designated PISA:1

Redundancy Status:designated

Interface:FastEthernet2/10 IP is enabled

  hw[EGRESS] = 1, hw[INGRESS] = 1

  hw_force_default[EGRESS] = 0, hw_force_default[INGRESS] = 0

  mcast = 0

  priority = 2

  reflexive = 0

  inbound label:1

        protocol:ip

          feature #:1

          feature id:FM_IP_ACCESS

          ACL:106

  outbound label:2

        protocol:ip

          feature #:1

          feature id:FM_IP_ACCESS

          ACL:106

Interface:FastEthernet2/26 IP is enabled

  hw[EGRESS] = 1, hw[INGRESS] = 0

  hw_force_default[EGRESS] = 0, hw_force_default[INGRESS] = 1

  mcast = 0

  priority = 2

  reflexive = 0

  inbound label:24

        protocol:ip

          feature #:1

          feature id:FM_IP_ACCESS

          ACL:113

  outbound label:3

        protocol:ip

          feature #:1                                           feature

id:FM_IP_WCCP

          Service ID:0

          Service Type:0

Interface:Vlan55 IP is enabled

  hw[EGRESS] = 1, hw[INGRESS] = 1

  hw_force_default[EGRESS] = 0, hw_force_default[INGRESS] = 0

  mcast = 0

  priority = 2

  reflexive = 0

  inbound label:4

        protocol:ip

          feature #:1

          feature id:FM_IP_ACCESS

          ACL:111

Interface:Vlan101 IP is enabled

  hw[EGRESS] = 1, hw[INGRESS] = 1

  hw_force_default[EGRESS] = 0, hw_force_default[INGRESS] = 0

  mcast = 0

  priority = 2

  reflexive = 0

  inbound label:5

        protocol:ip

          feature #:1

          feature id:FM_IP_ACCESS

          ACL:101

  outbound label:6

        protocol:ip

          feature #:1

          feature id:FM_IP_ACCESS

          ACL:101

Router>

This example shows how to display the lines of feature manager information starting with the line that begins with Redundancy:

Router> show fm features | begin Redundancy

Redundancy Status: designated

Router>

show fm inband-counters

To display the number of inband packets that are sent by the PISA for SLB and WCCP, use the show fm inband-counters command.

show fm inband-counters

Syntax Description

This command has no keywords or arguments.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

The output display for the show fm inband-counters command includes the number of SLB inband packets that are sent by the PISA and the number of WCCP inband packets that are sent by the PISA.

If CBAC is configured, the command output displays the number of packets that are sent for CBAC by the PISA.

Examples

This example shows how to display the number of SLB and WCCP inband packets that are sent by the PISA:

Router# show fm inband-counters

      Inband Packets Sent

 Slot  WCCP         SLB

 1     0            0

 2     0            0

 3     0            0

 4     0            0

 5     0            0

 6     0            0

 7     0            0

 8     0            0

 9     0            0

 10    0            0

 11    0            0

 12    0            0

 13    0            0

Router#

show fm insp

To display the list and status of the ACLs and ports on which CBAC is configured, use the show fm insp command.

show fm insp [detail]

Syntax Description


detail	(Optional) Displays all of the flow information.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

If you can configure a VACL on the port before you configure CBAC, the status displayed is INACTIVE; otherwise, it is ACTIVE. If PFC resources are exhausted, the command displays BRIDGE and is followed by the number of failed currently active NetFlow requests that have been sent to the PISA for processing.

The show fm insp command output includes this information:

•interface:—Interface on which the IP inspect feature is enabled

•(direction)—Direction in which the IP inspect feature is enabled (IN or OUT)

•acl name:—Name that is used to identify packets that are being inspected

•status:—(ACTIVE or INACTIVE) displays if HW-assist is provided for this interface+direction (ACTIVE=hardware assisted or INACTIVE)

The optional detail keyword displays the ACEs that are part of the ACL that is used for IP inspect on the given interface direction.

Examples

This example shows how to display the list and status of CBAC-configured ACLs and ports:

Router> show fm insp

         interface:Vlan305(in) status :ACTIVE

         acl name:deny

           interfaces:

              Vlan305(out):status ACTIVE

show fm interface

To display the detailed information about the feature manager on a per-interface basis, use the show fm interface command.

show fm interface {{interface interface-number} | {null interface-number} | {port-channel number} | {vlan vlan-id}}

Syntax Description


interface	Interface type; possible valid values are ethernet, fastethernet, gigabitethernet, tengigabitethernet, pos, atm, and ge-wan.
interface-number	Module and port number; see the "Usage Guidelines" section for valid values.
null interface-number	Specifies the null interface; the valid value is 0.
port-channel number	Specifies the channel interface; valid values are a maximum of 64 values ranging from 1 to 282.
vlan vlan-id	Specifies the VLAN; valid values are from 1 to 4094.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

The interface-number argument designates the module and port number. Valid values for interface-number depend on the specified interface type and the chassis and module that are used. For example, if you specify a Gigabit Ethernet interface and have a 48-port 10/100BASE-T Ethernet module that is installed in a 13-slot chassis, valid values for the module number are from 1 to 13 and valid values for the port number are from 1 to 48.

The port-channel number values from 257 to 282 are supported on the CSM and the FWSM only.

Examples

This example shows how to display the detailed information about the feature manager on a specified interface:

Router# show fm interface fastethernet 2/26

Interface:FastEthernet2/26 IP is enabled

  hw[EGRESS] = 1, hw[INGRESS] = 0

  hw_force_default[EGRESS] = 0, hw_force_default[INGRESS] = 1

  mcast = 0

  priority = 2

  reflexive = 0

  inbound label:24

        protocol:ip

          feature #:1

          feature id:FM_IP_ACCESS

          ACL:113

                vmr IP value #1:0, 0, 0, 0, 0, 0, 0, 6 - 1

                vmr IP mask #1:0, 0, FFFF, FFFF, 0, 0, 0, FF

                vmr IP value #2:642D4122, 0, 0, 0, 1, 0, 0, 6 - 1

                vmr IP mask #2:FFFFFFFF, 0, 0, 0, 1, 0, 0, FF

                vmr IP value #3:0, 64020302, 0, 0, 6, 0, 0, 6 - 1

                vmr IP mask #3:0, FFFFFFFF, 0, 0, 6, 0, 0, FF

                vmr IP value #4:0, 64020302, 0, 0, A, 0, 0, 6 - 1

                vmr IP mask #4:0, FFFFFFFF, 0, 0, A, 0, 0, FF

                vmr IP value #5:0, 64020302, 0, 0, 12, 0, 0, 6 - 1

                vmr IP mask #5:0, FFFFFFFF, 0, 0, 12, 0, 0, FF

                vmr IP value #6:0, 0, 0, 0, 0, 0, 0, 0 - 2

                vmr IP mask #6:0, 0, 0, 0, 0, 0, 0, 0

  outbound label:3

        protocol:ip

          feature #:1

          feature id:FM_IP_WCCP

          Service ID:0

          Service Type:0

Router#

This example shows how to display the detailed information about the feature manager on a specific VLAN:

Router# show fm interface vlan 21

Interface: Vlan21 IP is disabled

hw_state[INGRESS] = not reduced, hw_state[EGRESS] = not reduced

mcast = 0

priority = 0

flags = 0x0

inbound label: 8

Feature IP_VACL:

-----------------------------------------------------------------------------

FM_FEATURE_IP_VACL_INGRESS i/f: Vl21 map name: test

=============================================================================

------------------------------------------------------------

IP Seq. No: 10 Seq. Result : VACL_ACTION_FORWARD_CAPTURE

------------------------------------------------------------

DPort - Destination Port SPort - Source Port Pro - Protocol

X - XTAG TOS - TOS Value Res - VMR Result

RFM - R-Recirc. Flag MRTNP - M-Multicast Flag R - Reflexive flag

- F-Fragment flag - T-Tcp Control N - Non-cachable

- M-More Fragments - P-Mask Priority(H-High, L-Low)

Adj. - Adj. Index T - M(Mask)/V(Value) FM - Flow Mask

NULL - Null FM SAO - Source Only FM DAO - Dest. Only FM

SADA - Sour.& Dest. Only VSADA - Vlan SADA Only FF - Full Flow

VFF - Vlan Full Flow F-VFF - Either FF or VFF A-VSD - Atleast VSADA

A-FF - Atleast FF A-VFF - Atleast VFF A-SON - Atleast SAO

A-DON - Atleast DAO A-SD - Atleast SADA SHORT - Shortest

A-SFF - Any short than FF A-EFF - Any except FF A-EVFF- Any except VFF

A-LVFF- Any less than VFF ERR - Flowmask Error

+----+-+---------------+---------------+-----+-----+---+---+-+---+-----+----+------+

|Indx|T| Dest Ip Addr | Source Ip Addr|DPort|SPort|Pro|RFM|X|ToS|MRTNP|Adj.| FM |

+----+-+---------------+---------------+-----+-----+---+---+-+---+-----+----+------+

1 V 22.2.2.2 21.1.1.1 0 0 0 --- 0 0 ----L ---- SHORT

M 255.255.255.255 255.255.255.255 0 0 0 000 0 0

TM_PERMIT_RESULT

2 V 32.2.2.2 31.1.1.1 0 0 0 --- 0 0 ----L ---- SHORT

M 255.255.255.255 255.255.255.255 0 0 0 000 0 0

TM_PERMIT_RESULT

3 V 0.0.0.0 0.0.0.0 0 0 0 --- 0 0 ----L ---- SHORT

M 0.0.0.0 0.0.0.0 0 0 0 000 0 0

TM_L3_DENY_RESULT

------------------------------------------------------------

IP Seq. No: 65536 Seq. Result : VACL_ACTION_DROP

------------------------------------------------------------

+----+-+---------------+---------------+-----+-----+---+---+-+---+-----+----+------+

|Indx|T| Dest Ip Addr | Source Ip Addr|DPort|SPort|Pro|RFM|X|ToS|MRTNP|Adj.| FM |

+----+-+---------------+---------------+-----+-----+---+---+-+---+-----+----+------+

1 V 0.0.0.0 0.0.0.0 0 0 0 --- 0 0 ----L ---- SHORT

M 0.0.0.0 0.0.0.0 0 0 0 000 0 0

TM_PERMIT_RESULT

Router#

show fm ipv6 traffic-filter

To display the IPv6 information, use the show fm ipv6 traffic-filter command.

show fm ipv6 traffic-filter {all | {interface interface interface-number}}

Syntax Description


all	Displays IPv6 traffic filter information for all interfaces.
interface interface	Displays IPv6 traffic filter information for the specifed interface; possible valid values are ethernet, fastethernet, gigabitethernet, tengigabitethernet, pos, atm, and ge-wan.
interface-number	Module and port number; see the "Usage Guidelines" section for valid values.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

Examples

This example shows how to display the IPv6 information for a specific interface:

Router# show fm ipv6 traffic-filter interface vlan 50

-----------------------------------------------------------------------------

FM_FEATURE_IPV6_ACG_INGRESS Name:testipv6 i/f: Vlan50

=============================================================================

DPort - Destination Port SPort - Source Port Pro - Protocol

X - XTAG TOS - TOS Value Res - VMR Result

RFM - R-Recirc. Flag MRTNP - M-Multicast Flag R - Reflexive flag

- F-Fragment flag - T-Tcp Control N - Non-cachable

- M-More Fragments - P-Mask Priority(H-High, L-Low)

Adj. - Adj. Index T - M(Mask)/V(Value) FM - Flow Mask

NULL - Null FM SAO - Source Only FM DAO - Dest. Only FM

SADA - Sour.& Dest. Only VSADA - Vlan SADA Only FF - Full Flow

VFF - Vlan Full Flow F-VFF - Either FF or VFF A-VSD - Atleast VSADA

A-FF - Atleast FF A-VFF - Atleast VFF A-SON - Atleast SAO

A-DON - Atleast DAO A-SD - Atleast SADA SHORT - Shortest

A-SFF - Any short than FF A-EFF - Any except FF A-EVFF- Any except VFF

A-LVFF- Any less than VFF ERR - Flowmask Error

+----+-+----------------------------------------+----------------------------------------+
---+---+-+-----+----+------+

|Indx|T| Dest IPv6 Addr | Source IPv6

Addr |Pro|RFM|X|MRTNP|Adj.| FM |

+----+-+----------------------------------------+----------------------------------------+
---+---+-+-----+----+------+

1 V 0:200E::

200D::1 0 -F- - ----L ---- Shorte

M 0:FFFF:FFFF:FFFF:FFFF::

FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF 0 1

TM_SOFT_BRIDGE_RESULT

2 V 0:200E::

200D::1 17 --- - ----L ---- Shorte

M 0:FFFF:FFFF:FFFF:FFFF::

FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF 255 0

TM_PERMIT_RESULT

3 V 200E::

200D::1 0 -F- - ----L ---- Shorte

M FFFF:FFFF:FFFF:FFFF::

FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF 0 1

TM_SOFT_BRIDGE_RESULT

4 V 200E::

200D::1 17 --- - ----L ---- Shorte

M FFFF:FFFF:FFFF:FFFF::

FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF 255 0

TM_PERMIT_RESULT

5 V

:: :: 0 -F- - ----L ---- Shorte

:: :: 0 1

TM_SOFT_BRIDGE_RESULT

6 V

:: :: 0 -F- - ----L ---- Shorte

:: :: 0 1

TM_SOFT_BRIDGE_RESULT

7 V

:: :: 58 --- - ----L ---- Shorte

:: :: 255 0

TM_PERMIT_RESULT

8 V

:: :: 58 --- - ----L ---- Shorte

:: :: 255 0

TM_PERMIT_RESULT

9 V

:: :: 58 --- - ----L ---- Shorte

:: :: 255 0

TM_PERMIT_RESULT

10 V

:: :: 58 --- - ----L ---- Shorte

:: :: 255 0

TM_PERMIT_RESULT

11 V

:: :: 58 --- - ----L ---- Shorte

:: :: 255 0

TM_PERMIT_RESULT

12 V

:: :: 58 --- - ----L ---- Shorte

:: :: 255 0

TM_PERMIT_RESULT

13 V

:: :: 58 --- - ----L ---- Shorte

:: :: 255 0

TM_PERMIT_RESULT

14 V

:: :: 58 --- - ----L ---- Shorte

:: :: 255 0

TM_PERMIT_RESULT

15 V

:: :: 0 --- - ----L ---- Shorte

:: :: 0 0

TM_L3_DENY_RESULT

Router#

This example shows how to display the IPv6 information for all interfaces:

Router# show fm ipv6 traffic-filter all

-----------------------------------------------------------------------------

FM_FEATURE_IPV6_ACG_INGRESS Name:testipv6 i/f: Vlan50

=============================================================================

DPort - Destination Port SPort - Source Port Pro - Protocol

X - XTAG TOS - TOS Value Res - VMR Result

RFM - R-Recirc. Flag MRTNP - M-Multicast Flag R - Reflexive flag

- F-Fragment flag - T-Tcp Control N - Non-cachable

- M-More Fragments - P-Mask Priority(H-High, L-Low)

Adj. - Adj. Index T - M(Mask)/V(Value) FM - Flow Mask

NULL - Null FM SAO - Source Only FM DAO - Dest. Only FM

SADA - Sour.& Dest. Only VSADA - Vlan SADA Only FF - Full Flow

VFF - Vlan Full Flow F-VFF - Either FF or VFF A-VSD - Atleast VSADA

A-FF - Atleast FF A-VFF - Atleast VFF A-SON - Atleast SAO

A-DON - Atleast DAO A-SD - Atleast SADA SHORT - Shortest

A-SFF - Any short than FF A-EFF - Any except FF A-EVFF- Any except VFF

A-LVFF- Any less than VFF ERR - Flowmask Error

+----+-+----------------------------------------+----------------------------------------+
---+---+-+-----+----+------+

|Indx|T| Dest IPv6 Addr | Source IPv6

Addr |Pro|RFM|X|MRTNP|Adj.| FM |

+----+-+----------------------------------------+----------------------------------------+
---+---+-+-----+----+------+

1 V 0:200E::

200D::1 0 -F- - ----L ---- Shorte

M 0:FFFF:FFFF:FFFF:FFFF::

FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF 0 1

TM_SOFT_BRIDGE_RESULT

2 V 0:200E::

200D::1 17 --- - ----L ---- Shorte

M 0:FFFF:FFFF:FFFF:FFFF::

FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF 255 0

TM_PERMIT_RESULT

3 V 200E::

200D::1 0 -F- - ----L ---- Shorte

M FFFF:FFFF:FFFF:FFFF::

FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF 0 1

TM_SOFT_BRIDGE_RESULT

4 V 200E::

200D::1 17 --- - ----L ---- Shorte

M FFFF:FFFF:FFFF:FFFF::

FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF 255 0

TM_PERMIT_RESULT

5 V

:: :: 0 -F- - ----L ---- Shorte

:: :: 0 1

TM_SOFT_BRIDGE_RESULT

6 V

:: :: 0 -F- - ----L ---- Shorte

:: :: 0 1

TM_SOFT_BRIDGE_RESULT

7 V

:: :: 58 --- - ----L ---- Shorte

:: :: 255 0

TM_PERMIT_RESULT

8 V

:: :: 58 --- - ----L ---- Shorte

:: :: 255 0

TM_PERMIT_RESULT

9 V

:: :: 58 --- - ----L ---- Shorte

:: :: 255 0

TM_PERMIT_RESULT

10 V

:: :: 58 --- - ----L ---- Shorte

:: :: 255 0

13 V

:: :: 58 --- - ----L ---- Shorte

:: :: 255 0

. Output is truncated

Interface(s) using this IPv6 Ingress Traffic Filter:

Vl50,

show fm nat netflow data

To display the information about the NAT-related NetFlow data, use the show fm nat netflow data command.

show fm nat netflow data

Syntax Description

This command has no keywords or arguments.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Examples

This example shows how to display the information about the NAT-related NetFlow data:

Router> show fm nat netflow data

FM Pattern with stat push disabled: 1

Default/TCP/UDP Timeouts:

Def s/w timeout: 86400 h/w timeout: 300 Pattern(ingress): 4

Pattern(egress): 4 Push interval: 1333

TCP s/w timeout: 86400 h/w timeout: 300 Pattern(ingress): 4

Pattern(egress): 4 Push interval: 1333

UDP s/w timeout: 300 h/w timeout: 300 Pattern(ingress): 3

Pattern(egress): 3 Push interval: 100

Port Timeouts:

Idle timeout :3600 secs

Fin/Rst timeout :10 secs

Fin/Rst Inband packets sent per timeout :10000

Netflow mode to Zero-out Layer4 information for fragment packet lookup :

Enabled

Router>

show fm reflexive

To display the information about the reflexive entry for the dynamic feature manager, use the show fm reflexive command.

show fm reflexive

Syntax Description

This command has no keywords or arguments.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Examples

This example shows how to display the information about the reflexive entry for the dynamic feature manager:

Router# show fm reflexive

       Reflexive hash table:

        Vlan613:refacl, OUT-REF, 64060E0A, 64060D0A, 0, 0, 7, 783, 6

Router#

show fm summary

To display a summary of feature manager information, use the show fm summary command.

show fm summary

Syntax Description

This command has no keywords or arguments.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Examples

This example shows how to display a summary of feature manager information:

Router# show fm summary

Current global ACL merge algorithm:BDD

Interface:FastEthernet2/10

  ACL merge algorithm used:

    inbound direction:  ODM

    outbound direction:BDD

  TCAM screening for features is ACTIVE outbound

  TCAM screening for features is ACTIVE inbound

Interface:FastEthernet2/26

  ACL merge algorithm used:

    inbound direction:  ODM

    outbound direction:BDD

  TCAM screening for features is ACTIVE outbound

  TCAM screening for features is INACTIVE inbound

Router#

show fm vlan

To display the information about the per-VLAN feature manager, use the show fm vlan command.

show fm vlan vlan-id

Syntax Description


vlan-id	VLAN ID; valid values are from 1 to 4094.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Examples

This example shows how to display the information about the per-VLAN feature manager:

Router# show fm vlan 1

hw[EGRESS] = 1, hw[INGRESS] = 1

hw_force_default[EGRESS] = 0, hw_force_default[INGRESS] = 0

mcast = 0

priority = 2

reflexive = 0

vacc_map : map1

inbound label: 5

merge_err: 0

protocol: ip

feature #: 1

feature id: FM_VACL

map_name: map1

seq #: 10

(only for IP_PROT) DestAddr SrcAddr Dpt Spt L4OP TOS Est prot Rslt

vmr IP value # 1: 0.0.0.0 0.0.0.0 0 0 0 0 0 6 permit

vmr IP mask # 1: 0.0.0.0 0.0.0.0 0 0 0 0 0 FF

vmr IP value # 2: 0.0.0.0 0.0.0.0 0 0 0 0 0 11 permit

vmr IP mask # 2: 0.0.0.0 0.0.0.0 0 0 0 0 0 FF

vmr IP value # 3: 0.0.0.0 0.0.0.0 0 0 0 0 0 0 deny

vmr IP mask # 3: 0.0.0.0 0.0.0.0 0 0 0 0 0 0

seq #: 65536

(only for IP_PROT) DestAddr SrcAddr Dpt Spt L4OP TOS Est prot Rslt

vmr IP value # 1: 0.0.0.0 0.0.0.0 0 0 0 0 0 0 permit

vmr IP mask # 1: 0.0.0.0 0.0.0.0 0 0 0 0 0 0

outbound label: 6

merge_err: 0

protocol: ip

feature #: 1

feature id: FM_VACL

map_name: map1

seq #: 10

(only for IP_PROT) DestAddr SrcAddr Dpt Spt L4OP TOS Est prot Rslt

vmr IP value # 1: 0.0.0.0 0.0.0.0 0 0 0 0 0 6 permit

vmr IP mask # 1: 0.0.0.0 0.0.0.0 0 0 0 0 0 FF

vmr IP value # 2: 0.0.0.0 0.0.0.0 0 0 0 0 0 11 permit

vmr IP mask # 2: 0.0.0.0 0.0.0.0 0 0 0 0 0 FF

vmr IP value # 3: 0.0.0.0 0.0.0.0 0 0 0 0 0 0 deny

vmr IP mask # 3: 0.0.0.0 0.0.0.0 0 0 0 0 0 0

seq #: 65536

(only for IP_PROT) DestAddr SrcAddr Dpt Spt L4OP TOS Est prot Rslt

vmr IP value # 1: 0.0.0.0 0.0.0.0 0 0 0 0 0 0 permit

vmr IP mask # 1: 0.0.0.0 0.0.0.0 0 0 0 0 0 0

show icc

To display the information about the ICC counter and status, use the show icc command.

show icc {counters | status}

Syntax Description


counters	Specifies the counter information.
status	Specifies the status information.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Examples

This example shows how to display the information about the ICC counter:

Router# show icc counters

total tx RPC packets to slot 1 LCP = 0

  detail by request id: (<request-id>=<number-of-packets>)

   2 =0            7 =0            8 =0            10=0

   11=0            12=0            14=0            17=0

   18=0            19=0            20=0

total rx RPC packets from slot 1 LCP = 0

  detail by request id: (<request-id>=<number-of-packets>)

   2 =5            7 =7            8 =11           10=4

   11=1            12=2            14=1            17=67

   18=7            19=159          20=29

total tx MCAST-SP packets to slot 1 LCP = 0

  detail by request id: (<request-id>=<number-of-packets>)

   6 =0            7 =0            8 =0            9 =0

   12=0            14=0

total rx MCAST-SP packets from slot 1 LCP = 0

  detail by request id: (<request-id>=<number-of-packets>)

   6 =1            7 =1            8 =1            9 =1

   12=41           14=67

total tx L3-MGR packets to slot 1 LCP = 0

  detail by request id: (<request-id>=<number-of-packets>)

   1 =0            2 =0            3 =0

total rx L3-MGR packets from slot 1 LCP = 0

  detail by request id: (<request-id>=<number-of-packets>)

   1 =1            2 =2            3 =1

Router#

This example shows how to display the information about the ICC status:

Router# show icc status

Class Name             Msgs Pending  Max Pending  Total Sent

----- ---------------- ------------  -----------  ----------

    2 RPC                         0            3         403

    3 MSC                         0            1           1

    5 L3-MGR                      0            4        4173

   13 TCAM-API                    0           10          26

Router#

show idprom

To display the IDPROMs for FRUs, use the show idprom command.

show idprom {all | frutype | interface interface slot} [detail]

Syntax Description


all	Displays the information for all FRU types.
frutype	Type of FRU to display information; see the "Usage Guidelines" section for valid values.
interface interface slot	Specifies the interface to display information; valid values are as follows: •interface—GigabitEthernet •slot—1 to 13 See the "Usage Guidelines" section for additional information.
detail	(Optional) Displays the details of the IDPROM data (verbose).

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

Valid frutypes are as follows:

•backplane—No arguments.

•clock number—1 and 2.

•earl slot—See the following paragraph for valid values.

•module slot—See the following paragraph for valid values.

•rp slot—See the following paragraph for valid values.

•power-supply—1 and 2.

•supervisor slot—See the following paragraph for valid values.

•vtt number—1 to 3.

The slot argument designates the module and port number. Valid values for slot depend on the specified interface type and the chassis and module that are used. For example, if you specify a Gigabit Ethernet interface and have a 48-port 10/100BASE-T Ethernet module that is installed in a 13-slot chassis, valid values for the module number are from 1 to 13 and valid values for the port number are from 1 to 48.

Use the show idprom backplane command to display the chassis serial number.

The optional interface interface slot keyword and arguments are supported on GBIC security-enabled interfaces only.

Examples

This example shows how to display IDPROM information for clock 1:

Router> show idprom clock 1

IDPROM for clock #1

  (FRU is 'Clock FRU')

  OEM String = 'Cisco Systems'

  Product Number = 'WS-C6000-CL'

  Serial Number = 'SMT03073115'

  Manufacturing Assembly Number = '73-3047-04'

  Manufacturing Assembly Revision = 'A0'

  Hardware Revision = 1.0

  Current supplied (+) or consumed (-) = 0.000A

Router>

This example shows how to display IDPROM information for power supply 1:

Router> show idprom power-supply 1

IDPROM for power-supply #1

  (FRU is '110/220v AC power supply, 1360 watt')

  OEM String = 'Cisco Systems, Inc.'

  Product Number = 'WS-CAC-1300W'

  Serial Number = 'ACP03020001'

  Manufacturing Assembly Number = '34-0918-01'

  Manufacturing Assembly Revision = 'A0'

  Hardware Revision = 1.0

  Current supplied (+) or consumed (-) = 27.460A

Router>

This example shows how to display detailed IDPROM information for power supply 1:

Router# show idprom power-supply 1 detail

IDPROM for power-supply #1

IDPROM image:

  (FRU is '110/220v AC power supply, 1360 watt')

IDPROM image block #0:

  hexadecimal contents of block:

  00: AB AB 01 90 11 BE 01 00 00 02 AB 01 00 01 43 69    ..............Ci

  10: 73 63 6F 20 53 79 73 74 65 6D 73 2C 20 49 6E 63    sco Systems, Inc

  20: 2E 00 57 53 2D 43 41 43 2D 31 33 30 30 57 00 00    ..WS-CAC-1300W..

  30: 00 00 00 00 00 00 41 43 50 30 33 30 32 30 30 30    ......ACP0302000

  40: 31 00 00 00 00 00 00 00 00 00 33 34 2D 30 39 31    1.........34-091

  50: 38 2D 30 31 00 00 00 00 00 00 41 30 00 00 00 00    8-01......A0....

  60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00    ................

  70: 00 00 00 01 00 00 00 00 00 00 00 09 00 0C 00 03    ................

  80: 00 01 00 06 00 01 00 00 00 00 0A BA 00 00 00 00    ................

  block-signature = 0xABAB, block-version = 1,

  block-length = 144, block-checksum = 4542

  *** common-block ***

  IDPROM capacity (bytes) = 256  IDPROM block-count = 2

  FRU type = (0xAB01,1)

  OEM String = 'Cisco Systems, Inc.'

  Product Number = 'WS-CAC-1300W'

  Serial Number = 'ACP03020001'

  Manufacturing Assembly Number = '34-0918-01'

  Manufacturing Assembly Revision = 'A0'

  Hardware Revision = 1.0

  Manufacturing bits = 0x0  Engineering bits = 0x0

  SNMP OID = 9.12.3.1.6.1.0

  Power Consumption = 2746 centiamperes    RMA failure code = 0-0-0-0

  *** end of common block ***

IDPROM image block #1:

  hexadecimal contents of block:

  00: AB 01 01 14 02 5F 00 00 00 00 00 00 00 00 0A BA    ....._..........

  10: 0A BA 00 16                                        ....

  block-signature = 0xAB01, block-version = 1,

  block-length = 20, block-checksum = 607

  *** power supply block ***

  feature-bits:  00000000 00000000

  rated current at 110v:  2746    rated current at 220v:  2746   (centiamperes)

  CISCO-STACK-MIB SNMP OID = 22  *** end of power supply block ***

End of IDPROM image

Router#

This example shows how to display IDPROM information for the backplane:

Router# show idprom backplane

IDPROM for backplane #0

  (FRU is 'Catalyst 6000 9-slot backplane')

  OEM String = 'Cisco Systems'

  Product Number = 'WS-C6009'

  Serial Number = 'SCA030900JA'

  Manufacturing Assembly Number = '73-3046-04'

  Manufacturing Assembly Revision = 'A0'

  Hardware Revision = 1.0

  Current supplied (+) or consumed (-) = 0.000A

Router#

This example shows how to display IDPROM information from a GBIC security-enabled interface:

Router# show idprom interface g5/1

GBIC Serial EEPROM Contents:

Common block:

Identifier :

Connector :

Transceiver

Speed :

Media :

Technology :

Link Length :

GE Comp Codes :

SONET Comp Codes :

Encoding : 8B10B

BR, Nominal : 12x100 MHz

Length(9u) : GBIC does not support single mode fibre,

or the length information must be determined from

the transceiver technology.

Length(50u) : GBIC does not support 50 micron multi-mode fibre,

or the length information must be determined from

the transceiver technology.

Length(62.5u) : GBIC does not support 62.5 micron multi-mode fibre,

or the length information must be determined from

the transceiver technology.

Length(Copper) : GBIC does not support copper cables,

or the length information must be determined from

the transceiver technology.

Vendor Name : IBM

Vendor OUI : 0x8 0x0 0x5A

Vendor PN : IBM42P12SNY

Vendor rev : CS10

CC_BASE : 0xC6

Extended ID Fields

Options : Loss of Signal implemented TX_FAULT signal implemented

TX_D

ISABLE is implemented and disables the serial output

BR, max : 5%

BR, min : 5%

Vendor SN : 21P70420005D6

Date code : 02071001

CC_EXT : 0xCE

Vendor Specific ID Fields:

0x00: 00 00 00 70 2E DF C4 69 50 E6 54 F9 05 D4 83 A2

0x10: 4B 0E 8B 00 00 00 00 00 00 00 00 00 7D 3F D9 1E

Router#

show interfaces

To display traffic that is seen by a specific interface, use the show interfaces command.

show interfaces [{interface interface-number} | {null interface-number} | {vlan vlan-id}]

Syntax Description


interface	(Optional) Interface type; possible valid values are ethernet, fastethernet, gigabitethernet, tengigabitethernet, pos, and port-channel, atm, and ge-wan.
interface-number	(Optional) Module and port number; see the "Usage Guidelines" section for valid values.
null interface-number	(Optional) Specifies the null interface; the valid value is 0.
vlan vlan-id	(Optional) Specifies the VLAN ID; valid values are from 1 to 4094.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

The valid values for port-channel are from 1 to 308. The port-channel values that are from 257 to 282 are internally allocated, and are supported on the CSM and the FWSM only.

Statistics are collected on a per-VLAN basis for Layer 2-switched packets and Layer 3-switched packets. Statistics are available for both unicast and multicast traffic. The Layer 3-switched packet counts are available for both ingress and egress directions. The per-VLAN statistics are updated every 5 seconds.

In some cases, you might see a difference in the duplex mode that is displayed between the show interfaces command and the show running-config commands. In this case, the duplex mode that is displayed in the show interfaces command is the actual duplex mode that the interface is running. The show interfaces command shows the operating mode for an interface, while the show running-config command shows the configured mode for an interface.

If you do not enter any keywords, all counters for all modules are displayed.

The output of the show interfaces GigabitEthernet command displays an extra 4 bytes for every packet that is sent or received. This display occurs on the LAN ports on the GE-WAN module and other Catalyst 6500 series switch Gigabit Ethernet LAN modules. The extra 4 bytes are the Ethernet frame CRC in the input and output byte statistics.

Examples

This example shows how to display traffic for a specific interface:

Router# show interfaces GigabitEthernet3/3

GigabitEthernet3/3 is up, line protocol is up (connected)

  Hardware is C6k 1000Mb 802.3, address is 000f.2305.49c0 (bia 000f.2305.49c0)

  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation 802.1Q Virtual LAN, Vlan ID  1., loopback not set

  Keepalive set (10 sec)

  Full-duplex, 1000Mb/s, media type is LH

  input flow-control is off, output flow-control is on

  Clock mode is auto

  ARP type: ARPA, ARP Timeout 04:00:00

  Last input 00:00:19, output 00:00:00, output hang never

  Last clearing of "show interface" counters never

  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

  Queueing strategy: fifo

  Output queue: 0/40 (size/max)

  5 minute input rate 0 bits/sec, 0 packets/sec

  5 minute output rate 0 bits/sec, 0 packets/sec

  L2 Switched: ucast: 360 pkt, 23040 bytes - mcast: 0 pkt, 0 bytes

  L3 in Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes mcast

  L3 out Switched: ucast: 0 pkt, 0 bytes mcast: 0 pkt, 0 bytes

     437 packets input, 48503 bytes, 0 no buffer

     Received 76 broadcasts (0 IP multicast)

     0 runts, 0 giants, 0 throttles

     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

     0 watchdog, 0 multicast, 0 pause input

     0 input packets with dribble condition detected

     86 packets output, 25910 bytes, 0 underruns <===========

     0 output errors, 0 collisions, 0 interface resets

     0 babbles, 0 late collision, 0 deferred

     0 lost carrier, 0 no carrier, 0 PAUSE output

     0 output buffer failures, 0 output buffers swapped out

Router#

This example shows how to display traffic for a FlexWAN module:

Router# show interfaces pos 6/1/0.1

POS6/1/0.1 is up, line protocol is up

  Hardware is Packet over Sonet

  Internet address is 1.1.2.2/24

  MTU 4470 bytes, BW 155000 Kbit, DLY 100 usec,

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation FRAME-RELAY <<<+++ no packets info after this line

Arches#sh mod 6

Mod Ports Card Type                              Model              Serial No.

--- ----- -------------------------------------- ------------------ -----------

  6    0  2 port adapter FlexWAN                 WS-X6182-2PA       SAD04340JY3

Mod MAC addresses                       Hw    Fw           Sw           Status

--- ---------------------------------- ------ ------------ ------------ -------

  6  0001.6412.a234 to 0001.6412.a273   1.3   12.2(2004022 12.2(2004022 Ok

Mod Online Diag Status

--- -------------------

  6 Pass

Router#

show interfaces accounting

To display the number of packets of each protocol type that have been sent through all configured interfaces, use the show interfaces accounting command.

show interfaces [{interface interface-number} | {null interface-number} | {vlan vlan-id}] accounting

Syntax Description


interface	(Optional) Interface type; possible valid values are ethernet, fastethernet, gigabitethernet, tengigabitethernet, pos, and port-channel, atm, and ge-wan.
interface-number	(Optional) Module and port number; see the "Usage Guidelines" section for valid values.
null interface-number	(Optional) Specifies the null interface; the valid value is 0.
vlan vlan-id	(Optional) Specifies the VLAN ID; valid values are from 1 to 4094.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

Note The Pkts Out and Chars Out fields display IPv6 packet counts only. The Pkts In and Chars In fields display both IPv4 and IPv6 packet counts, except for tunnel interfaces. For tunnel interfaces, the IPv6 input packets are counted as IPv6 packets only.

The port channels from 257 to 282 are internally allocated and are supported on the CSM and the FWSM only.

If you do not enter any keywords, all counters for all modules are displayed.

Examples

This example shows how to display the number of packets of each protocol type that have been sent through all configured interfaces:

Router# show interfaces gigabitethernet5/2 accounting

GigabitEthernet5/2

Protocol Pkts In Chars In Pkts Out Chars Out

IP       50521   50521000 0        0

DEC MOP  0       0        1        129

CDP      0       0        1        592

IPv6     11      834      96       131658

Router#

Table 2-37 describes the fields that are shown in the example.

Table 2-37 show interfaces accounting Command Output Fields
Field	Description
Protocol	Protocol that is operating on the interface.
Pkts In	Number of IPv4 packets received for the specified protocol.
Chars In	Number of IPv4 characters received for the specified protocol.
Pkts Out	Number of hardware-switched IPv6 packets transmitted for the specified protocol.
Chars Out	Number of IPv6 characters transmitted for the specified protocol.

show interfaces capabilities

To display the interface capabilities for a module, an interface, or all interfaces, use the show interfaces capabilities command.

show interfaces [interface interface-number] capabilities [{module number}]

Syntax Description


interface	(Optional) Interface type; possible valid values are ethernet, fastethernet, gigabitethernet, tengigabitethernet, pos, atm, and port-channel, and ge-wan.
interface-number	Module and port number; see the "Usage Guidelines" section for valid values.
module number	(Optional) Specifies the module number; see the "Usage Guidelines" section for valid values.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

The interface-number argument designates the module and port number. Valid values for interface-number depend on the chassis and module that are used. For example, if you have a 48-port 10/100BASE-T Ethernet module that is installed in a 13-slot chassis, valid values for the slot number are from 2 to 13 and valid values for the port number are from 1 to 48.

The port-channel values are from 0 to 282; values from 257 to 282 are supported on the CSM and the FWSM only.

Examples

This example shows how to display the interface capabilities for a module:

Router# show interfaces capabilities module 6

FastEthernet6/1

Dot1x: yes

Model: WS-X6248-RJ-45

Type: 10/100BaseTX

Speed: 10,100,auto

Duplex: half,full

Trunk encap. type: 802.1Q,ISL

Trunk mode: on,off,desirable,nonegotiate

Channel: yes

Broadcast suppression: percentage(0-100)

Flowcontrol: rx-(off,on),tx-(none)

Membership: static

Fast Start: yes

QOS scheduling: rx-(1q4t), tx-(2q2t)

CoS rewrite: yes

ToS rewrite: yes

Inline power: no

SPAN: source/destination

UDLD yes

Link Debounce: yes

Link Debounce Time: no

Ports on ASIC: 1-12

Port-Security: yes

Router#

This example shows how to display the interface capabilities for an interface:

Router# show interfaces fastethernet 4/1 capabilities

FastEthernet4/1

Model: WS-X6348-RJ-45

Type: 10/100BaseTX

Speed: 10,100,auto

Duplex: half,full

Trunk encap. type: 802.1Q,ISL

Trunk mode: on,off,desirable,nonegotiate

Channel: yes

Broadcast suppression: percentage(0-100)

Flowcontrol: rx-(off,on),tx-(none)

Fast Start: yes

QOS scheduling: rx-(1q4t), tx-(2q2t)

CoS rewrite: yes

ToS rewrite: yes

Inline power: no

SPAN: source/destination

This example shows how to display the port-channel interface capabilities:

Router# show interfaces port-channel 12 capabilities

Port-channel12

  Model:                 NO IDPROM

  Type:                  unknown

  Speed:                 10,100,1000,auto

  Duplex:                half,full

  Trunk encap. type:     802.1Q,ISL

  Trunk mode:            on,off,desirable,nonegotiate

  Channel:               yes

  Broadcast suppression: percentage(0-100)

  Flowcontrol:           rx-(off,on),tx-(none)

  Fast Start:            yes

  QOS scheduling:        rx-(1q4t), tx-(1q4t)

  CoS rewrite:           yes

  ToS rewrite:           yes

  Inline power:          no

  SPAN:                  source/destination

Router#

show interfaces counters

To display the traffic that the physical interface sees, use the show interfaces counters command.

show interfaces [interface] counters [errors | etherchannel | {module number} | {protocol status} | {trunk [module number]}]

Syntax Description


interface	(Optional) Interface type; for a list of valid values, see the "Usage Guidelines" section.
errors	(Optional) Displays the interface-error counters.
etherchannel	(Optional) Displays information about the EtherChannel interface.
module number	(Optional) Displays the module number; see the "Usage Guidelines" section for valid values.
protocol status	(Optional) Displays the current status of the enabled protocols.
trunk	(Optional) Displays the interface-trunk counters.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

The show interfaces [interface] counters command displays the number of all of the packets arriving and includes the number of packets that may be dropped by the interface due to the storm-control settings. To display the total number of dropped packets, you can enter the show interfaces [interface] counters storm-control command.

If you do not enter any keywords, all counters for all modules are displayed.

When you enter the interface, these formats can be used:

•card-type {slot}/{first-port} - {last-port}

You can define a single port range per command entry. If you specify a range of ports, the range must consist of the same slot and port type.

When you define a range, you must enter a white space between the first port and the hyphen (-) as follows:

show interfaces gigabitethernet7/1 -7 counters

The module number keyword and argument designate the module number and limit the display to interfaces on the module. Valid values depend on the chassis that is used. For example, if you have a 13-slot chassis, valid values for the module number are from 1 to 13.

Valid values for card-type are as follows:

•ethernet

•fastethernet

•gigabitethernet

•tengigabitethernet

•port-channel interface-number—Valid values are from 1 to 282; values from 257 to 282 are supported on the CSM and the FWSM only.

When you enter the show interfaces interface counters etherchannel command, follow these guidelines:

•If interface specifies a physical port, the command displays this message, "Etherchnl not enabled on this interface."

•If interface is omitted, the command displays the counters for all port channels (in the system) and for their associated physical ports.

•If interface specifies a port channel, the command displays the counters for the port channel and all of the physical ports that are associated with it. In addition, when you enter the command specifying the primary aggregator in a LACP port channel with multiple aggregators, the output includes the statistics for all of the aggregators in the port channels and for the ports that are associated with them.

Examples

This example shows how to display the error counters for a specific module:

Router# show interfaces counters errors module 1

Port        Align-Err    FCS-Err   Xmit-Err    Rcv-Err UnderSize

Gi1/1               0          0          0          0         0

Gi1/2               0          0          0          0         0

Port      Single-Col Multi-Col  Late-Col Excess-Col Carri-Sen     Runts    Giant

Gi1/1              0         0         0          0         0         0        0

Gi1/2              0         0         0          0         0         0        0

Router#

This example shows how to display traffic that is seen by a specific module:

Router# show interfaces counters module 1

Port            InOctets   InUcastPkts   InMcastPkts   InBcastPkts

Gi1/1                  0             0             0             0

Gi1/2                  0             0             0             0

Port           OutOctets  OutUcastPkts  OutMcastPkts  OutBcastPkts

Gi1/1                  0             0             0             0

Gi1/2                  0             0             0             0

Router#

This example shows how to display the trunk counters for a specific module:

Router# show interfaces counters trunk module 1

Port        TrunkFramesTx  TrunkFramesRx  WrongEncap

Gi1/1                   0              0           0

Gi1/2                   0              0           0

Router#

This example shows how to display the counters for all port channels (in the system) and their associated physical ports:

Router# show interfaces counters etherchannel

Port            InOctets   InUcastPkts   InMcastPkts   InBcastPkts

Po1                 5518             1            29             1

Fa3/48              5518             1            29             1

Po2                11897             2            54             2

Fa3/45              5878             1            27             1

Fa3/46              6019             1            27             1

Po3                    0             0             0             0

Po5                 6073             1            27             1

Fa3/44              6073             1            27             1

Po5A                7811             1            53             1

Fa3/43              7811             1            53             1

Port           OutOctets  OutUcastPkts  OutMcastPkts  OutBcastPkts

Po1                 4333             1            24             1

Fa3/48              4333             1            24             1

Po2                 9532             2            46             2

Fa3/45              4766             1            23             1

Fa3/46              4766             1            23             1

Po3                    0             0             0             0

Po5                17224             1           214             1

Fa3/44             17224             1           214             1

Po5A              174426             1          2669             1

Fa3/43            174426             1          2669             1

This example shows how to display the counters for a specific port channel and the counters for the associated physical ports:

Router# show interfaces port-channel2 counters etherchannel

Port            InOctets   InUcastPkts   InMcastPkts   InBcastPkts

Po2                 6007             1            31             1

Fa3/48              6007             1            31             1

Port           OutOctets  OutUcastPkts  OutMcastPkts  OutBcastPkts

Po2                 4428             1            25             1

Fa3/48              4428             1            25             1

Router#

This example shows how to display the discard count and the level settings for each mode:

Router# show interfaces counters storm-control

Port         UcastSupp %     McastSupp %     BcastSupp %  TotalSuppDiscards

Fa5/1             100.0           100.0           100.0                   0

Fa5/2             100.0           100.0           100.0                   0

Fa5/3             100.0           100.0           100.0                   0

Router#

Related Commands


Command	Description
clear counters	Clears the interface counters.

show interfaces debounce

To display the status and configuration for the debounce timer, use the show interfaces debounce command.

show interfaces [{interface interface-number} | {null interface-number} | {vlan vlan-id}] debounce [module num]

Syntax Description


interface	(Optional) Interface type; possible valid values are ethernet, fastethernet, gigabitethernet, tengigabitethernet, port-channel, pos, atm, and ge-wan.
interface-number	(Optional) Module and port number; see the "Usage Guidelines" section for valid values.
null interface-number	(Optional) Specifies the null interface; the valid value is 0.
vlan vlan-id	(Optional) Specifies the VLAN; valid values are from 1 to 4094.
module num	(Optional) Limits the display to interfaces on the specified module.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

The debounce timer is not supported on the 10-Gigabit Ethernet module (WSX-6502-10GE).

The port-channel values are from 0 to 282; values from 257 to 282 are supported on the CSM and the FWSM only.

Examples

This example shows how to display the debounce configuration of an interface:

Router# show interfaces GigabitEthernet1/1 debounce

Port   Debounce time   Value

Gi1/1   enable          100

Router#

Related Commands


Command	Description
link debounce	Enables the debounce timer on an interface.

show interfaces description

To display a description and a status of an interface, use the show interfaces description command.

show interfaces [interface] description

Syntax Description


interface	(Optional) Interface type; for a list of valid values, see the "Usage Guidelines" section.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

When you enter the interface value, these formats can be used:

•card-type {slot}/{first-port} - {last-port}

You can define a single port range per command entry. If you specify a range of ports, the range must consist of the same slot and port type. When you define a range, you must enter a space before and after the hyphen (-) as follows:

show interfaces gigabitethernet7/1 - 7 counters broadcast

Possible valid values for card-type are ethernet, fastethernet, gigabitethernet, tengigabitethernet, port-channel, pos, atm, and ge-wan.

The port-channel values are from 0 to 282; values from 257 to 282 are supported on the CSM and the FWSM only.

Examples

This example shows how to display the information for all interfaces:

Router# show interfaces description

 Interface Status         Protocol Description

 PO0/0     admin down     down     First POS interface

 PO0/1     admin down     down

 Gi1/0     up             up       GigE to server farm

Router#

Related Commands


Command	Description
description	Includes a specific description about the DSP interface.

show interfaces flowcontrol

To display flow-control information, use the show interfaces flowcontrol command.

show interfaces [interface [mod]] flowcontrol [module number]

Syntax Description


interface	(Optional) Interface type; possible valid values are ethernet, fastethernet, gigabitethernet, tengigabitethernet, port-channel, pos, atm, and ge-wan.
mod	(Optional) Module and port number.
module number	(Optional) Specifies the module number; see the "Usage Guidelines" section for valid values.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

The mod argument designates the module and port number. Valid values for mod depend on the chassis and module that are used. For example, if you have a 48-port 10/100BASE-T Ethernet module that is installed in a 13-slot chassis, valid values for the slot number are from 1 to 13 and valid values for the port number are from 1 to 48.

The port-channel values are from 0 to 282; values from 257 to 282 are supported on the CSM and the FWSM only.

Examples

This example shows how to display flow-control information for all interfaces:

Router# show interfaces flowcontrol

Port  Send    FlowControl Receive FlowControl RxPause TxPause

      admin     oper      admin     oper

----- --------  --------  --------  --------  -------  -------

Gi1/1 desired   off       off       off       0        0

Gi1/2 desired   off       off       off       0        0

Gi3/1 on        on        on        on        0        0

Gi8/2 desired   off       off       off       0        0

Gi8/3 desired   off       off       off       0        0

Gi8/4 desired   off       off       off       0        0

Router#

This example shows how to display flow-control information for a specific interface:

Router# show interfaces gigabitethernet 8/2 flowcontrol

Port  Send    FlowControl Receive FlowControl RxPause TxPause

      admin     oper      admin     oper

----- --------  --------  --------  --------  -------  -------

Gi8/2 desired   off       off       off       0        0

Router#

Table 2-38 describes the fields that are shown in the example.

Table 2-38 show port flowcontrol Command Output Fields
Field	Description
Port	Interface type and module and port number.
Send admin	Flow-control operation for admin state. On indicates that the local port is allowed to send pause frames to remote ports, off indicates that the local port is prevented from sending pause frames to remote ports, and desired indicates predictable results whether a remote port is set to receive on, receive off, or receive desired.
Send oper	Current flow-control operation. On indicates that the local port is allowed to send pause frames to remote ports, off indicates that the local port is prevented from sending pause frames to remote ports, and desired indicates predictable results whether a remote port is set to receive on, receive off, or receive desired.
Receive admin	Flow-control operation for admin state. On indicates that the local port is allowed to send pause frames to remote ports, off indicates that the local port is prevented from sending pause frames to remote ports, and desired indicates predictable results whether a remote port is set to send on, send off, or send desired.
Receive oper	Current flow-control operation. On indicates that the local port is allowed to send pause frames to remote ports, off indicates that the local port is prevented from sending pause frames to remote ports, and desired indicates predictable results whether a remote port is set to send on, send off, or send desired.
RxPause	Number of pause frames that are received.
TxPause	Number of pause frames that are transmitted.

Related Commands


Command	Description
flowcontrol	Configures a port to send or receive pause frames.

show interfaces private-vlan mapping

To display the information about the PVLAN mapping for VLAN SVIs, use the show interfaces private-vlan mapping command.

show interfaces [interface interface-number] private-vlan mapping [active]

Syntax Description


interface	(Optional) Interface type; possible valid values are ethernet, fastethernet, gigabitethernet, tengigabitethernet, pos, atm, and ge-wan.
interface-number	Module and port number; see the "Usage Guidelines" section for valid values.
active	(Optional) Displays the active interfaces only.

Command Default

This command has no default settings.

Command Default

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

This command displays SVI information only.

The interface-number argument designates the module and port number. Valid values for interface-number depend on the chassis and module that are used. For example, if you have a 48-port 10/100BASE-T Ethernet module that is installed in a 13-slot chassis, valid values for the slot number are from 1 to 13 and valid values for the port number are from 1 to 48.

Examples

This example shows how to display the information about the PVLAN mapping:

Router# show interfaces private-vlan mapping

Interface Secondary VLAN Type

--------- -------------- -----------------

vlan2     301            community

vlan2     302            community

Router#

Related Commands


Command	Description
private-vlan	Configures PVLANs and the association between a PVLAN and a secondary VLAN.
private-vlan mapping	Creates a mapping between the primary and the secondary VLANs so that both VLANs share the same primary VLAN SVI.

show interfaces status

To display the interface status or a list of interfaces in an error-disabled state on LAN ports only, use the show interfaces status command.

show interfaces [interface interface-number] status [err-disabled | module number]

Syntax Description


interface	(Optional) Interface type; possible valid values are ethernet, fastethernet, gigabitethernet, tengigabitethernet, pos, atm, and ge-wan.
interface-number	Module and port number; see the "Usage Guidelines" section for valid values.
err-disabled	(Optional) Displays the LAN ports in an error-disabled state.
module number	(Optional) Specifies the module number; see the "Usage Guidelines" section for valid values.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

The interface-number argument designates the module and port number. Valid values for interface-number depend on the chassis and module that are used. For example, if you have a 48-port 10/100BASE-T Ethernet module that is installed in a 13-slot chassis, valid values for the slot number are from 1 to 13 and valid values for the port number are from 1 to 48.

This command is supported on LAN ports only.

The module number keyword and argument designate the module number and limit the display to the interfaces on the module. Valid values depend on the chassis that is used. For example, if you have a 13-slot chassis, valid values for the module number are from 1 to 13.

To find out if an interface is inactive, enter the show interfaces status command. If the interface is inactive, the Status field displays "inactive." If the port is not inactive, the Status field displays "none."

To find the packet and byte count, you can enter the show interfaces counters command or the show interfaces interface interface-number status command. The show interfaces counters command is the preferred command to use. In some cases, the packet and byte count of the show interfaces interface interface-number status command is incorrect.

Examples

This example shows how to display the status of all LAN ports:

Router# show interfaces status

Port    Name               Status     Vlan       Duplex Speed Type

Gi1/1                      disabled   routed       full  1000 missing

Gi1/2                      notconnect 1            full  1000 unknown (4)

Fa5/1                      disabled   routed       auto  auto 10/100BaseTX

Port    Name               Status       Vlan       Duplex  Speed Type

Fa5/18                     disabled     1          auto    auto  10/100BaseTX

Fa5/19                     disabled     1          auto    auto  10/100BaseTX

Gi7/1                      disabled     1          full    1000  WDM-RXONLY

Gi7/2                      disabled     1          full    1000  No Transceiver

Router#

This example shows how to display the packet and byte count of a specific LAN port:

Router# show interfaces fastethernet5/2 status

FastEthernet5/2

Switching path    Pkts In   Chars In   Pkts Out  Chars Out

               Processor         17       1220         20       2020

             Route cache          0          0          0          0

       Distributed cache         17       1220  206712817 2411846570

                   Total         34       2440  206712837 2411848590

Router#

This example shows how to display the status of LAN ports in an error-disabled state:

Router# show interfaces status err-disabled

Port    Name               Status       Reason

Fa9/4                      notconnect   link-flap

informational error message when the timer expires on a cause

--------------------------------------------------------------

5d04h:%PM-SP-4-ERR_RECOVER:Attempting to recover from link-flap err-disable state on Fa9/4

Router#

Related Commands


Command	Description
errdisable detect cause	Enables the error-disable detection.
show errdisable recovery	Displays the information about the error-disable recovery timer.

show interfaces summary

To display a summary of statistics for all interfaces that are configured on a networking device, use the show interfaces summary command.

show interfaces [interface interface-number] summary [vlan]

Syntax Description


interface	(Optional) Interface type; possible valid values are ethernet, fastethernet, gigabitethernet, tengigabitethernet, pos, atm, and ge-wan.
interface-number	Module and port number; see the "Usage Guidelines" section for valid values.
vlan	(Optional) Displays the total number of VLAN interfaces.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

Separate counters for subinterfaces are not maintained and are not displayed in the show interfaces summary output.

Examples

This example shows how to display a summary of statistics for all interfaces that are configured on a networking device:

Router# show interfaces summary

*: interface is up

IHQ: pkts in input hold queue IQD: pkts dropped from input queue

OHQ: pkts in output hold queue OQD: pkts dropped from output queue

RXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)

TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)

TRTL: throttle count

Interface IHQ IQD OHQ OQD RXBS RXPS TXBS TXPS TRTL

----------------------------------------------------------------------

* FastEthernet0/0 0 0 0 0 0 0 0 0 0

Serial0/0 0 0 0 0 0 0 0 0 0

FastEthernet0/1 0 0 0 0 0 0 0 0 0

Serial0/1 0 0 0 0 0 0 0 0 0

Router#

This example shows how to display the total number of VLAN interfaces:

Router# show interfaces summary vlan

Total number of Vlan interfaces: 7

Vlan interfaces configured:

1,5,20,2000,3000-3001,4000

Router#

show interfaces switchport

To display the administrative and operational status of a switching (nonrouting) port, use the show interfaces switchport command.

show interfaces [interface interface-number] switchport [brief] [module number]

Syntax Description


interface	(Optional) Interface type; possible valid values are ethernet, fastethernet, gigabitethernet, tengigabitethernet, pos, atm, and ge-wan.
interface-number	Module and port number; see the "Usage Guidelines" section for valid values.
brief	(Optional) Displays a brief summary of information.
module number	(Optional) Limits the display to interfaces on a specified module; see the "Usage Guidelines" section for valid values.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

The interface-number designates the module and port number. Valid values depend on the chassis and module that are used. For example, if you have a 48-port 10/100BASE-T Ethernet module that is installed in a 13-slot chassis, valid values for the slot number are from 1 to 13 and valid values for the port number are from 1 to 48.

Examples

This example shows how to display switch-port information using the include output modifier:

Router# show interfaces switchport | include VLAN

Name: Fa5/6

Access Mode VLAN: 200 (VLAN0200)

Trunking Native Mode VLAN: 1 (default)

Trunking VLANs Enabled: ALL

Pruning VLANs Enabled: ALL

Router#

This example shows how to display the configurations of two multiple VLAN access ports:

Router# show interfaces switchport

Name: Fa5/1

Switchport: Enabled

Administrative Mode: access

Operational Mode: access

Dot1q Ethertype: 0x8200

Operational Trunking Encapsulation: dot1q

Negotiation of Trunking: off

Access Mode VLAN: 100

Voice VLAN: 102

Trunking Native Mode VLAN: 1 (default)

Administrative private-vlan host-association: none

Administrative private-vlan mapping: 900 ((Inactive)) 901 ((Inactive))

Operational private-vlan: none

Trunking VLANs Enabled: ALL

Pruning VLANs Enabled: 2-1001

Capture Mode Disabled

Capture VLANs Allowed: ALL

Name: Fa5/2

Switchport: Enabled

Administrative Mode: access

Operational Mode: down

Dot1q Ethertype: 0x8200

Operational Trunking Encapsulation: native

Negotiation of Trunking: Off

Access Mode VLAN: 100

Voice VLAN: 103 ((inactive))

Trunking Native Mode VLAN: 1 (default)

This example shows how to display a brief summary of information:

Router# show interfaces switchport brief module 3

Port Status Op.Mode Op.Encap Channel-id Vlan

Fa3/1 connected access native -- 1

Fa3/7 disabled -- dot1q Po26 1

Fa3/13 connected access native -- 666

Router#

show interfaces switchport backup

To display Flexlink pairs, use the show interfaces switchport backup command.

show interfaces [interface interface-number] switchport backup

Syntax Description


interface	(Optional) Interface type; possible valid values are ethernet, fastethernet, gigabitethernet, tengigabitethernet, pos, atm, and ge-wan.
interface-number	Module and port number; see the "Usage Guidelines" section for valid values.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

Examples

This example shows how to display all Flexlink pairs:

Router# show interfaces switchport backup

Switch Backup Interface Pairs:

Active Interface        Backup Interface        State

------------------------------------------------------------------------

FastEthernet3/1         FastEthernet4/1         Active Up/Backup Standby

FastEthernet5/1         FastEthernet5/2         Active Down/Backup Up

FastEthernet3/2         FastEthernet5/4         Active Standby/Backup Up

Po1                     Po2                     Active Down/Backup Down

Router#

This example shows how to display a specific Flexlink port:

Router# show interfaces fastethernet 4/1 switchport backup

Switch Backup Interface Pairs:

Active Interface        Backup Interface        State

------------------------------------------------------------------------

FastEthernet3/1       FastEthernet4/1           Active Up/Backup Standby

Router#

Related Commands


Command	Description
switchport backup	Configures an interface as a Flexlink backup interface.

show interfaces transceiver

To display information about the optical transceivers that have DOM enabled, use the show interfaces transceiver command.

show interfaces [interface interface-number] transceiver [threshold violations] [detail | {module number}]

Syntax Description


interface	(Optional) Interface type; possible valid values are gigabitethernet and tengigabitethernet.
interface-number	Module and port number; see the "Usage Guidelines" section for valid values.
threshold violations	(Optional) Displays information about the interface transceiver threshold violations.
detail	(Optional) Displays detailed information about the interface transceiver.
module number	(Optional) Specifies the module number; see the "Usage Guidelines" section for valid values.

Command Default

This command has no default settings.

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

After a transceiver is inserted, the software waits approximately 10 seconds before reading the diagnostic monitoring information. If you enter the show interfaces transceiver command before the software has read the diagnostic monitoring information, the following message is displayed:

Waiting for diagnostic monitoring information to settle down.

Please try again after a few seconds.

Wait a few seconds and reenter the show interfaces transceiver command.

The interface interface-number arguments are supported on interfaces that have a transceiver that has diagnostic monitoring enabled and the transceiver is in a module that supports the reading of diagnostic monitoring information.

Examples

This example shows how to display transceiver information:

Router# show interfaces transceiver

If device is externally calibrated, only calibrated values are printed.

++ : high alarm, +  : high warning, -  : low warning, -- : low alarm.

NA or N/A: not applicable, Tx: transmit, Rx: receive.

mA: milliamperes, dBm: decibels (milliwatts).

                                         Optical   Optical

         Temperature  Voltage  Current   Tx Power  Rx Power

Port     (Celsius)    (Volts)  (mA)      (dBm)     (dBm)

-------  -----------  -------  --------  --------  --------

Gi1/1      40.6       5.09       0.4     -25.2      N/A

Gi2/1      35.5       5.05       0.1     -29.2      N/A

Gi2/2      49.5       3.30       0.0       7.1     -18.7

Router#

This example shows how to display detailed transceiver information:

Router# show interfaces transceiver detail

mA: milliamperes, dBm: decibels (milliwatts), NA or N/A: not applicable.

++ : high alarm, +  : high warning, -  : low warning, -- : low alarm.

A2D readouts (if they differ), are reported in parentheses.

The threshold values are calibrated.

                            High Alarm  High Warn  Low Warn   Low Alarm

        Temperature         Threshold   Threshold  Threshold  Threshold

Port     (Celsius)          (Celsius)   (Celsius)  (Celsius)  (Celsius)

------- ------------------  ----------  ---------  ---------  ---------

Gi1/1     48.1               100.0       100.0         0.0        0.0

Gi1/2     34.9               100.0       100.0         0.0        0.0

Gi2/1     43.5                70.0        60.0         5.0        0.0

Gi2/2     39.1                70.0        60.0         5.0        0.0

                            High Alarm  High Warn  Low Warn   Low Alarm

         Voltage            Threshold   Threshold  Threshold  Threshold

Port     (Volts)            (Volts)     (Volts)    (Volts)    (Volts)

-------  ---------------    ----------  ---------  ---------  ---------

Gi1/1    3.30                  6.50        6.50         N/A        N/A

Gi1/2    3.30                  6.50        6.50         N/A        N/A

Gi2/1    5.03                  5.50        5.25        4.75       4.50

Gi2/2    5.02                  5.50        5.25        4.75       4.50

                            High Alarm  High Warn  Low Warn   Low Alarm

         Current            Threshold   Threshold  Threshold  Threshold

Port     (milliamperes)     (mA)        (mA)       (mA)       (mA)

-------  -----------------  ----------  ---------  ---------  ---------

Gi1/1      0.0               130.0       130.0        N/A        N/A

Gi1/2      1.7               130.0       130.0        N/A        N/A

Gi2/1     50.6         +      60.0        40.0        10.0        5.0

Gi2/2     25.8                60.0        40.0        10.0        5.0

         Optical            High Alarm  High Warn  Low Warn   Low Alarm

         Transmit Power     Threshold   Threshold  Threshold  Threshold

Port     (dBm)              (dBm)       (dBm)      (dBm)      (dBm)

-------  -----------------  ----------  ---------  ---------  ---------

Gi1/1      8.1         ++      8.1         8.1        N/A        N/A

Gi1/2     -9.8                 8.1         8.1        N/A        N/A

Gi2/1    -16.7         --      3.4         3.2        -0.3       -0.5

Gi2/2      0.8                 3.4         3.2        -0.3       -0.5

         Optical            High Alarm  High Warn  Low Warn   Low Alarm

         Receive Power      Threshold   Threshold  Threshold  Threshold

Port     (dBm)              (dBm)       (dBm)      (dBm)      (dBm)

-------  -----------------  ----------  ---------  ---------  ---------

Gi1/1     N/A                  8.1         8.1        N/A        N/A

Gi1/2    -30.9                 8.1         8.1        N/A        N/A

Gi2/1     N/A                  5.9        -6.7       -28.5      -28.5

Gi2/2     N/A                  5.9        -6.7       -28.5      -28.5

Router#

This example shows how to display the threshold violations for all the transceivers on a Catalyst 6500 series switch:

Router# show interfaces transceiver threshold violations

        Rx: Receive, Tx: Transmit.

        DDDD: days, HH: hours, MM: minutes, SS: seconds

                                Time since Last Known

                Time in slot    Threshold Violation     Type(s) of Last Known

        Port    (DDDD:HH:MM:SS)  (DDDD:HH:MM:SS)        Threshold Violation(s)

        ------- --------------- ----------------------  ----------------------

        Gi1/1    0000:00:03:41    Not applicable        Not applicable

        Gi2/1    0000:00:03:40    0000:00:00:30         Tx bias high warning

                                                         50.5 mA >  40.0 mA

                                  0000:00:00:30         Tx power low alarm

                                                        -17.0 dBm <  -0.5 dBm

        Gi2/2    0000:00:03:40    Not applicable        Not applicable

Router#

This example shows how to display the threshold violations for all transceivers on a specific module:

Router# show interfaces transceiver threshold violations module 2

        lo: low, hi: high, warn: warning

        DDDD: days, HH: hours, MM: minutes, SS: seconds

                                Time since Last Known

                Time in slot    Threshold Violation     Type(s) of Last Known

        Port    (DDDD:HH:MM:SS)  (DDDD:HH:MM:SS)        Threshold Violation

        ------- --------------  ----------------------  ----------------------

        Gi2/1    0000:00:03:40    0000:00:00:30         Tx bias high warning

                                                         50.5 mA >  40.0 mA

                                  0000:00:00:30         Tx power low alarm

                                                        -17.0 dBm <  -0.5 dBm

        Gi2/2    0000:00:03:40    Not applicable        Not applicable

Router#

This example shows how to display violations for the transceiver on a specific interface:

Router# show interfaces Gi2/1 transceiver threshold violations

        Rx: Receive, Tx: Transmit.

        DDDD: days, HH: hours, MM: minutes, SS: seconds

                                Time since Last Known

                Time in slot    Threshold Violation     Type(s) of Last Known

        Port    (DDDD:HH:MM:SS)  (DDDD:HH:MM:SS)        Threshold Violation(s)

        ------- --------------- ----------------------  ----------------------

        Gi2/1    0000:00:03:40    0000:00:00:30         Tx bias high warning

                                                         50.5 mA >  40.0 mA

                                  0000:00:00:30         Tx power low alarm

                                                        -17.0 dBm <  -0.5 dBm

Router#

show interfaces trunk

To display the interface-trunk information, use the show interfaces trunk command.

show interfaces [interface interface-number] trunk [module number]

Syntax Description


interface	(Optional) Interface type; possible valid values are ethernet, fastethernet, gigabitethernet, tengigabitethernet, pos, atm, and ge-wan.
interface-number	(Optional) Module and port number; see the "Usage Guidelines" section for valid values.
module number	(Optional) Specifies the module number; see the "Usage Guidelines" section for valid values.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

If you do not specify a keyword, only information for trunking ports is displayed.

Examples

This example shows how to display the interface-trunk information for module 5:

Router# show interfaces trunk module 5

Port      Mode         Encapsulation  Status        Native vlan

Fa5/1     routed       negotiate      routed        1

Fa5/2     routed       negotiate      routed        1

Fa5/3     routed       negotiate      routed        1

Fa5/4     routed       negotiate      routed        1

Fa5/5     routed       negotiate      routed        1

Fa5/6     off          negotiate      not-trunking  10

Fa5/7     off          negotiate      not-trunking  10

Fa5/8     off          negotiate      not-trunking  1

Fa5/9     desirable    n-isl          trunking      1

Fa5/10    desirable    negotiate      not-trunking  1

Fa5/11    routed       negotiate      routed        1

Fa5/12    routed       negotiate      routed        1

Fa5/48    routed       negotiate      routed        1

Port      Vlans allowed on trunk

Fa5/1     none

Fa5/2     none

Fa5/3     none

Fa5/4     none

Fa5/5     none

Fa5/6     none

Fa5/7     none

Fa5/8     200

Fa5/9     1-1005

Fa5/10    none

Fa5/11    none

Fa5/12    none

Fa5/48    none

Port      Vlans allowed and active in management domain

Fa5/1     none

Fa5/2     none

Fa5/3     none

Fa5/4     none

Fa5/5     none

Fa5/6     none

Fa5/7     none

Fa5/8     200

Fa5/9     1-6,10,20,50,100,152,200,300,303-305,349-351,400,500,521,524,570,801-8

02,850,917,999,1002-1005

Fa5/10    none

Fa5/11    none

Fa5/12    none

Fa5/48    none

Port      Vlans in spanning tree forwarding state and not pruned

Fa5/1     none

Fa5/2     none

Fa5/3     none

Fa5/4     none

Fa5/5     none

Fa5/6     none

Fa5/7     none

Fa5/8     200

Fa5/9     1-6,10,20,50,100,152,200,300,303-305,349-351,400,500,521,524,570,801-8

02,850,917,999,1002-1005

Fa5/10    none

Fa5/11    none

Fa5/48    none

Router#

This example shows how to display the trunking information for active trunking ports:

Router# show interfaces trunk

Port      Mode         Encapsulation  Status        Native vlan

Fa5/9     desirable    n-isl          trunking      1

Port      Vlans allowed on trunk

Fa5/9     1-1005

Port      Vlans allowed and active in management domain

Fa5/9     1-6,10,20,50,100,152,200,300,303-305,349-351,400,500,521,524,570,801-8

02,850,917,999,1002-1005

Port      Vlans in spanning tree forwarding state and not pruned

Fa5/9     1-6,10,20,50,100,152,200,300,303-305,349-351,400,500,521,524,570,801-8

02,850,917,999,1002-1005

Router#

show interfaces unidirectional

To display the operational state of an interface with a receive-only transceiver, use the show interfaces unidirectional command.

show interfaces [interface interface-number] unidirectional [module number]

Syntax Description


interface	(Optional) Interface type; possible valid values are gigabitethernet and tengigabitethernet.
interface-number	(Optional) Module and port number; see the "Usage Guidelines" section for valid values.
module number	(Optional) Specifies the module number; see the "Usage Guidelines" section for valid values.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

If you do not specify a keyword, only information for trunking ports is displayed.

The interface-number designates the module and port number. Valid values depend on the chassis and module that are used. For example, if you have a 48-port 10/100BASE-T Ethernet module that is installed in a 13-slot chassis, valid values for the slot number are from 2 to 13 and valid values for the port number are from 1 to 48.

Examples

This example shows how to display the operational state of an interface with a receive-only transceiver:

Router# show interfaces gigabitethernet5/2 unidirectional

Unidirectional configuration mode: send only

Unidirectional operational mode: receive only

CDP neighbour unidirectional configuration mode: off

Router#

Related Commands


Command	Description
show interfaces status	Displays the interface status or a list of interfaces in an error-disabled state on LAN ports only.
unidirectional	Configures the software-based UDE.

show interfaces vlan mapping

To display the status of a VLAN mapping on a port, use the show interfaces vlan mapping command.

show interfaces [interface interface-number] vlan mapping

Syntax Description


interface	(Optional) Interface type; possible valid values are ethernet, fastethernet, gigabitethernet, tengigabitethernet, vlan, pos, atm, and ge-wan.
interface-number	Module and port number; see the "Usage Guidelines" section for valid values.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

The interface-number designates the module and port number or the VLAN number. Valid values depend on the chassis and module that are used. For example, if you have a 48-port 10/100BASE-T Ethernet module that is installed in a 13-slot chassis, valid values for the slot number are from 1 to 13 and valid values for the port number are from 1 to 48.

Examples

This example shows how to list all of the VLAN mappings that are configured on a port and indicate whether such mappings are enabled or disabled on the port:

Router# show interfaces gigabitethernet5/2 vlan mapping

State: enabled

Original VLAN Translated VLAN

------------- ---------------

  1649           755

Router#

Related Commands


Command	Description
show vlan mapping	Registers a mapping of an 802.1Q VLAN to an ISL VLAN.
switchport vlan mapping enable	Enables VLAN mapping per switch port.

show ip arp inspection

To display the status of DAI for a specific range of VLANs, use the show ip arp inspection command.

show ip arp inspection [{interfaces [interface-name]} | {statistics [vlan vlan-range]}]

Syntax Description


interfaces interface-name	(Optional) Displays the trust state and the rate limit of ARP packets for the provided interface.
statistics	(Optional) Displays statistics for the following types of packets that have been processed by this feature: forwarded, dropped, MAC validation failure, and IP validation failure.
vlan vlan-range	(Optional) Displays the statistics for the selected range of VLANs.

Command Default

This command has no default settings.

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

If you do not enter the statistics keyword, the configuration and operating state of DAI for the selected range of VLANs is displayed.

If you do not specify the interface name, the trust state and rate limit for all applicable interfaces in the system are displayed.

Examples

This example shows how to display the statistics of packets that have been processed by DAI for
VLAN 3:

Router# show ip arp inspection statistics vlan 3

 Vlan      Forwarded        Dropped     DHCP Drops     ACL Drops

 ----      ---------        -------     ----------     ----------

    3          31753         102407         102407              0

 Vlan   DHCP Permits    ACL Permits   Source MAC Failures

 ----   ------------    -----------   -------------------

    3          31753              0                    0

 Vlan   Dest MAC Failures   IP Validation Failures

 ----   -----------------   ----------------------

    3                  0                        0

Router#

This example shows how to display the statistics of packets that have been processed by DAI for all active VLANs:

Router# show ip arp inspection statistics

 Vlan      Forwarded        Dropped     DHCP Drops     ACL Drops

 ----      ---------        -------     ----------     ----------

    1              0              0              0              0

    2              0              0              0              0

    3          68322         220356         220356              0

    4              0              0              0              0

  100              0              0              0              0

  101              0              0              0              0

 1006              0              0              0              0

 1007              0              0              0              0

 Vlan   DHCP Permits    ACL Permits   Source MAC Failures

 ----   ------------    -----------   -------------------

    1              0              0                    0

    2              0              0                    0

    3          68322              0                    0

    4              0              0                    0

  100              0              0                    0

  101              0              0                    0

 1006              0              0                    0

 1007              0              0                    0

 Vlan   Dest MAC Failures   IP Validation Failures

 ----   -----------------   ----------------------

    1                  0                        0

    2                  0                        0

    3                  0                        0

    4                  0                        0

  100                  0                        0

  101                  0                        0

 1006                  0                        0

 1007                  0                        0

Router#

This example shows how to display the configuration and operating state of DAI for VLAN 1:

Router# show ip arp inspection vlan 1

Source Mac Validation      : Disabled

Destination Mac Validation : Disabled

IP Address Validation      : Disabled

 Vlan     Configuration    Operation   ACL Match          Static ACL

 ----     -------------    ---------   ---------          ----------

    1     Enabled          Active

 Vlan     ACL Logging      DHCP Logging

 ----     -----------      ------------

    1     Deny             Deny

Router#

This example shows how to display the trust state of interface Fa6/3:

Router# show ip arp inspection interfaces fastEthernet 6/3

Interface        Trust State     Rate (pps)    Burst Interval

 ---------------  -----------     ----------    --------------

 Fa6/1            Untrusted               20                 5

Router#

This example shows how to display the trust state of the interfaces on the switch:

Router# show ip arp inspection interfaces

Interface        Trust State     Rate (pps)

 ---------------  -----------     ----------

 Gi1/1            Untrusted               15

 Gi1/2            Untrusted               15

 Gi3/1            Untrusted               15

 Gi3/2            Untrusted               15

 Fa3/3            Trusted               None

 Fa3/4            Untrusted               15

 Fa3/5            Untrusted               15

 Fa3/6            Untrusted               15

 Fa3/7            Untrusted               15

Router#

Related Commands


Command	Description
arp access-list	Configures an ARP ACL for ARP inspection and QoS filtering and enters the ARP ACL configuration submode.
clear ip arp inspection log	Clears the status of the log buffer.
show ip arp inspection	Displays the status of DAI for a specific range of VLANs.

show ip arp inspection log

To show the status of the log buffer, use the show ip arp inspection log command.

show ip arp inspection log

Syntax Description

This command has no arguments or keywords.

Command Default

This command has no default settings.

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Examples

This example shows how to display the current contents of the log buffer before and after the buffers are cleared:

Router# show ip arp inspection log

Total Log Buffer Size : 10

Syslog rate : 0 entries per 10 seconds.

 Interface        Vlan   Sender MAC         Sender IP        Num of Pkts

 ---------------  -----  -----------------  ---------------  -----------

Fa6/3            1     0002.0002.0002  1.1.1.2          1(12:02:52 UTC Fri Apr 25 2003)

Fa6/3            1     0002.0002.0002  1.1.1.3          1(12:02:52 UTC Fri Apr 25 2003)

Fa6/3            1     0002.0002.0002  1.1.1.4          1(12:02:52 UTC Fri Apr 25 2003)

Fa6/3            1     0002.0002.0002  1.1.1.5          1(12:02:52 UTC Fri Apr 25 2003)

Fa6/3            1     0002.0002.0002  1.1.1.6          1(12:02:52 UTC Fri Apr 25 2003)

Fa6/3            1     0002.0002.0002  1.1.1.7          1(12:02:52 UTC Fri Apr 25 2003)

Fa6/3            1     0002.0002.0002  1.1.1.8          1(12:02:52 UTC Fri Apr 25 2003)

Fa6/3            1     0002.0002.0002  1.1.1.9          1(12:02:52 UTC Fri Apr 25 2003)

Fa6/3            1     0002.0002.0002  1.1.1.10         1(12:02:52 UTC Fri Apr 25 2003)

Fa6/3            1     0002.0002.0002  1.1.1.11         1(12:02:52 UTC Fri Apr 25 2003)

    --            --         --               --        5(12:02:52 UTC Fri Apr 25 2003)

Router#

This example shows how to clear the buffer with the clear ip arp inspection log command:

Router# clear ip arp inspection log

Router# show ip arp inspection log

Total Log Buffer Size : 10

Syslog rate : 0 entries per 10 seconds.

No entries in log buffer.

Router#

Related Commands


Command	Description
clear ip arp inspection log	Clears the status of the log buffer.
show ip arp inspection log	Shows the status of the log buffer.

show ip auth-proxy watch-list

To display the information about the authentication proxy watch list, use the show ip auth-proxy watch-list command.

show ip auth-proxy watch-list

Syntax Description

This command has no arguments or keywords.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Examples

This example shows how to display the information about the authentication proxy watch list:

Router# show ip auth-proxy watch-list

Authentication Proxy Watch-list is enabled

Watch-list expiry timeout is 2 minutes

Total number of watch-list entries: 3

 Source IP       Type         Violation-count

 12.0.0.2        MAX_RETRY    MAX_LIMIT

 12.0.0.3        TCP_NO_DATA  MAX_LIMIT

 1.2.3.4         CFGED        N/A

Total number of watch-listed users: 3

Router#

Related Commands


Command	Description
clear ip auth-proxy watch-list	Deletes a single watch-list entry or all watch-list entries.
ip auth-proxy max-login-attempts	Limits the number of login attempts at a firewall interface.
ip auth-proxy watch-list	Enables and configures an authentication proxy watch list.

show ipc

To display IPC information, use the show ipc command.

show ipc {nodes | ports [open] | queue | status}

Syntax Description


nodes	Displays the participating nodes.
ports	Displays the local IPC ports.
open	(Optional) Displays the open ports only.
queue	Displays the contents of the IPC-retransmission queue.
status	Displays the status of the local IPC server.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Examples

This example shows how to display participating nodes:

Router# show ipc nodes

There are 66 nodes in this IPC realm.

   ID     Type                 Name                       Last  Last

                                                          Sent  Heard

 2210000 Local      Card33                                0     0

 2000000 ICC        Card0                                 0     0

 2010000 ICC        Card1                                 0     0

 2020000 ICC        Card2                                 0     0

 2040000 ICC        Card4                                 0     0

<... output truncated ...>

 23E0000 ICC        Card62                                0     0

 23F0000 ICC        Card63                                0     0

   10000 ICC        IPC Master                            270   17070

Router#

This example shows how to display local IPC ports:

Router# show ipc ports

There are 6 ports defined.

Port ID        Type       Name

 2210000.1     unicast    Card33:Zone

 2210000.2     unicast    Card33:Echo

 2210000.3     unicast    Card33:Control

 2210000.4     unicast    Remote TTY Server Port

   10000.3     unicast    IPC Master:Control

 2210000.5     unknown    Card33:Request

     port_index = 0  seat_id = 0x10000    last sent = 0     last heard = 1158

     port_index = 1  seat_id = 0x10000    last sent = 0     last heard = 0

Router#

This example shows how to display open IPC ports:

Router# show ipc ports open

There are 4 ports defined.

Port ID        Type       Name

   10000.7     unicast    Unknown

     port_index = 0  last sent = 2     last heard = 0

   10000.8     unicast    Unknown

     port_index = 0  last sent = 0     last heard = 0

   10000.9     unicast    Unknown

     port_index = 0  last sent = 17753 last heard = 0

     port_index = 1  last sent = 0     last heard = 0

Router#

This example shows how to display the contents of the IPC-retransmission queue:

Router# show ipc queue

There are 0 IPC messages waiting for acknowledgement in the transmit queue.

There are 0 IPC messages waiting for a response.

There are 0 IPC messages waiting for additional fragments.

There are 2 messages currently in use by the system.

Router#

This example shows how to display the status of the local IPC server:

Router# show ipc status

IPC System Status:

This processor is a slave server.

1000 IPC message headers in cache

377053 messages in, 293133 out, 210699 delivered to local port,

83655 acknowledgements received, 83870 sent,

0 NACKS received, 0 sent,

0 messages dropped on input, 0 messages dropped on output

0 no local port, 0 destination unknown, 0 no transport

0 missing callback or queue, 0 duplicate ACKs, 0 retries,

0 message timeouts.

0 ipc_output failures, 0 mtu failures,

0 msg alloc failed, 0 emer msg alloc failed, 0 no origs for RPC replies

0 pak alloc failed, 0 memd alloc failed

0 no hwq, 0 failed opens, 0 hardware errors

No regular dropping of IPC output packets for test purposes

Router#

show ip cache flow

To display a summary of the NetFlow cache-flow entries, use the show ip cache flow command.

show ip cache flow [aggregation type [module num]]

Syntax Description


aggregation type	(Optional) Displays the configuration of a particular aggregation cache; see the "Usage Guidelines" section for valid values.
module num	(Optional) Displays information about a specific module.

Command Default

This command has no default settings.

Command Modes

EXEC (>)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

Valid values for aggregation type are as follows:

•as—AS aggregation cache

•destination-prefix—Destination-prefix aggregation cache

•prefix—Source/destination-prefix aggregation cache

•protocol-port—Protocol and port aggregation cache

•source-prefix—Source-prefix aggregation cache

If you enter the show ip cache flow aggregation command without the module num, the software-switched aggregation cache on the route processor (RP) is displayed.

Examples

This example shows how to display a summary of the NetFlow cache-flow entries:

Router# show ip cache flow

 IP packet size distribution (0 total packets):

  1-32 64 96 128 160 192 224 256 288 320 352 384 416

  .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000

 .000 .000

  512 544 576 1024 1536 2048 2560 3072 3584 4096 4608

  .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000

 IP Flow Switching Cache, 0 bytes

  0 active, 0 inactive, 0 added

  0 ager polls, 0 flow alloc failures

  Active flows timeout in 30 minutes

  Inactive flows timeout in 15 seconds

  last clearing of statistics never

 Protocol Total Flows Packets Bytes Packets Active(Sec)

 Idle(Sec)

 -------- Flows /Sec /Flow /Pkt /Sec /Flow

 /Flow

 SrcIf SrcIPaddress DstIf DstIPaddress Pr SrcP

DstP

 Pkts

 Displaying Hardware entries in Module 7

 SrcIf SrcIPaddress DstIPaddress Pr SrcP

 DstP Pkts

 Fa5/11 11.1.1.38 12.1.1.2 udp 63

 63 986796

 Fa5/11 11.1.1.39 12.1.1.2 udp 63

 63 986796

 Fa5/11 11.1.1.40 12.1.1.2 udp 63

 63 986796

 Fa5/11 11.1.1.41 12.1.1.2 udp 63

 63 986796

 Fa5/11 11.1.1.42 12.1.1.2 udp 63

 63 986796

 Fa5/11 11.1.1.43 12.1.1.2 udp 63

 63 986796

 Fa5/11 11.1.1.44 12.1.1.2 udp 63

 63 986796

 Fa5/11 11.1.1.45 12.1.1.2 udp 63

 63 986796

 Fa5/11 11.1.1.46 12.1.1.2 udp 63

 63 986796

 Fa5/11 11.1.1.47 12.1.1.2 udp 63

 63 986796

 Fa5/11 11.1.1.48 12.1.1.2 udp 63

 63 986796

Router#

This example shows how to display the information about a destination-prefix aggregation cache for a specific module:

Router# show ip cache flow aggregation destination-prefix module 1

IPFLOW_DST_PREFIX_AGGREGATION records and statistics for module :1

IP Flow Switching Cache, 278544 bytes

  2 active, 4094 inactive, 6 added

  236 ager polls, 0 flow alloc failures

  Active flows timeout in 30 minutes

  Inactive flows timeout in 15 seconds

Dst If         Dst Prefix      Msk  AS    Flows  Pkts B/Pk  Active

Gi7/9          9.1.0.0         /16  0     3003    12M   64  1699.8

Gi7/10         11.1.0.0        /16  0     3000  9873K   64  1699.8

Router#

Table 2-39 describes the show ip cache flow command output fields.

Table 2-39 show ip cache flow Command Output Fields—Packet Size Distribution
Field	Description
IP packet size distribution	Two lines below this banner that show the percentage distribution of packets by size range. In this display, 55.4% of the packets fall in the size range of 33 to 64 bytes.

Table 2-40 describes the fields in the flow-switching cache lines of the output.

Table 2-40 show ip cache flow Command Output Fields—Flow-Switching Cache
Field	Description
bytes	Number of bytes of memory that the NetFlow cache uses.
active	Number of active flows in the NetFlow cache at the time this command was entered.
inactive	Number of flow buffers that are allocated in the NetFlow cache but are not currently assigned to a specific flow at the time this command was entered.
added	Number of flows that were created since the start of the summary period.
ager polls	Number of times that the NetFlow code looked at the cache to expire entries (used by Cisco for diagnostics only).
flow alloc failures	Number of times that the NetFlow code tried to allocate a flow but could not.
Exporting flows to	IP address and UDP port number of the workstation to which flows are exported.
Exporting using source interface	Interface type that is used as the source IP address.
Version 5 flow records, peer-as	Exported packets that use version 5 format and the export statistics that include the peer AS for the source and destination. The number of records stored in the datagram is between 1 and 30 for version 5.
Active flows timeout in	Timeout period for active flows in the NetFlow cache.
flows exported in udp datagrams	Total number of flows that are exported and the total number of UDP datagrams that are used to export the flows to the workstation.
failed	Number of flows that could not be exported by the router because of output interface limitations.
last clearing of statistics	Standard time output (hh:mm:ss) since the clear ip flow stats command was executed. This time output changes to hours and days after the time exceeds 24 hours.

Table 2-41 describes the fields in the NetFlow cctivity by protocol lines of the output.

Table 2-41 show ip cache flow Command Output Fields—NetFlow Activity by Protocol
Field	Description
Protocol	IP protocol and the well-known port number as described in RFC 1340.
Total Flows	Number of flows for this protocol since the last time that the statistics were cleared.
Flows/Sec	Average number of flows for this protocol seen per second; equal to total flows/number of seconds for this summary period.
Packets/Flow	Average number of packets observed for the flows seen for this protocol. Equal to total packets for this protocol/number of flows for this protocol for this summary period.
Bytes/Pkt	Average number of bytes observed for the packets seen for this protocol. Equal to total bytes for this protocol/total number of packets for this protocol for this summary period.
Packets/Sec	Average number of packets for this protocol per second. Equal to total packets for this protocol/total number of seconds for this summary period.
Active(Sec)/Flow	Sum of all the seconds from the first packet to the last packet of an expired flow (for example, TCP FIN, time-out, and so forth) in seconds/total flows for this protocol for this summary period.
Idle(Sec)/Flow	Sum of all the seconds from the last packet seen in each nonexpired flow for this protocol until the time this command was entered in seconds/total flows for this summary period.

Table 2-42 describes the fields in the current flow lines of the output.

Table 2-42 show ip cache flow Command Output Fields—Current Flow
Field	Description
SrcIf	Internal port name for the source interface.
SrcIPaddress	Source-IP address for this flow.
DstIf	Router internal port name for the destination interface.
DstIPaddress	Destination-IP address for this flow.
Pr	IP protocol; for example, 6=TCP, 17=UDP, .... as defined in RFC 1340.
SrcP	Source port address, TCP/UDP "well known" port number, as defined in RFC 1340.
DstP	Destination-port address, TCP/UDP "well known" port number, as defined in RFC 1340.
Pkts	Number of packets observed for this flow.
B/Pkt	Average observed number of bytes per packet for this flow.
Active	Number of seconds between first and last packet of a flow.

Related Commands


Command	Description
ip flow-aggregation cache	Creates a flow-aggregation cache and enters the aggregation cache configuration mode.
ip flow-cache entries	Changes the number of entries that are maintained in the NetFlow cache.
clear ip flow stats	Clears the NetFlow-switching statistics.

show ip cache verbose flow

To display a detailed summary of NetFlow statistics, use the show ip cache verbose flow command.

show ip cache verbose flow

Syntax Description

This command has no keywords or arguments.

Command Default

This command has no default settings.

Command Modes

Privileged EXEC (#)

Command History


Release	Modification
12.2(18)ZY	Support for this command was introduced.

Usage Guidelines

Use the show ip cache verbose flow command to display the flow record fields in the NetFlow cache in addition to the fields that are displayed with the show ip cache flow command. The values in the additional fields that are shown depend on the NetFlow features that are enabled and the flags that are set in the flow.

Note The flags and the fields displayed vary from flow to flow.

When you configure the MPLS-aware NetFlow feature, you can use the show ip cache verbose flow command to display both the IP and MPLS portions of the MPLS flows in the NetFlow cache on a router module. To display only the IP portion of the flow record in the NetFlow cache when MPLS-aware NetFlow is configured, use the show ip cache flow command.

Examples

This example shows how to display a detailed summary of NetFlow statistics:

Router# show ip cache verbose flow

IP packet size distribution (1094508 total packets):

   1-32   64   96  128  160  192  224  256  288  320  352  384  416  448  480

   .000 1.00 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000

    512  544  576 1024 1536 2048 2560 3072 3584 4096 4608

   .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000

IP Flow Switching Cache, 4456704 bytes

  2 active, 65534 inactive, 2 added

  298 ager polls, 0 flow alloc failures

  Active flows timeout in 30 minutes

  Inactive flows timeout in 15 seconds

IP Sub Flow Cache, 270600 bytes

  4 active, 16380 inactive, 4 added, 2 added to flow

  0 alloc failures, 0 force free

  1 chunk, 1 chunk added

  last clearing of statistics never

Protocol         Total    Flows   Packets Bytes  Packets Active(Sec) Idle(Sec)

--------         Flows     /Sec     /Flow  /Pkt     /Sec     /Flow     /Flow

SrcIf          SrcIPaddress    DstIf          DstIPaddress    Pr TOS Flgs  Pkts

Port Msk AS                    Port Msk AS    NextHop              B/Pk  Active

IPM: OPkts    OBytes

SrcIf          SrcIPaddress    DstIf          DstIPaddress    Pr TOS Flgs  Pkts

Port Msk AS                    Port Msk AS    NextHop              B/Pk  Active

IPM: OPkts    OBytes

Fa5/11         11.1.1.2        Fa5/12         12.1.1.2        06 5B  00     551K

0000 /16 0                     0000 /16 0     12.1.1.2               46   149.7

FO: 1

Fa5/11         11.1.1.3        Fa5/12         12.1.1.2        06 5B  00     553K

0000 /16 0                     0000 /16 0     12.1.1.2               46   150.4

FO: 1

Displaying Hardware entries in Module 7

 SrcIf            SrcIPaddress          DstIPaddress      Pr       SrcP      DstP      
Pkts

 --               0.0.0.0               0.0.0.0           0        0         0         3

Router#

Table 2-43 describes the fields shown in the NetFlow cache lines of the display.

Table 2-43 show ip cache verbose flow Field Descriptions in the NetFlow Cache Display
Field	Description
bytes	Number of bytes of memory that are used by the NetFlow cache.
active	Number of active flows in the NetFlow cache at the time this command was entered.
inactive	Number of flow buffers that are allocated in the NetFlow cache but that are not assigned to a specific flow at the time this command is entered.
added	Number of flows that were created since the start of the summary period.
ager polls	Number of times that the NetFlow code caused entries to expire (used by Cisco for diagnostics only).
flow alloc failures	Number of times that the NetFlow code tried to allocate a flow but could not.
last clearing of statistics	Standard time output (hh:mm:ss) since the clear ip flow stats privileged EXEC command was last executed. This time output changes to hours and days after the time exceeds 24 hours.

Table 2-44 describes the fields shown in the activity by the protocol lines of the display.

Table 2-44 show ip cache verbose flow Field Descriptions in Activity By Protocol Display
Field	Description
Protocol	IP protocol and port number. (Go to http://www.iana.org, Protocol Assignment Number Services, for the latest RFC values.) Note Only a small subset of all protocols is displayed.
Total Flows	Number of flows for this protocol since the last time statistics were cleared.
Flows/Sec	Average number of flows for this protocol per second; equal to the total flows divided by the number of seconds for this summary period.
Packets/Flow	Average number of packets for the flows for this protocol; equal to the total packets for this protocol divided by the number of flows for this protocol for this summary period.
Bytes/Pkt	Average number of bytes for the packets for this protocol; equal to the total bytes for this protocol divided by the total number of packets for this protocol for this summary period.
Packets/Sec	Average number of packets for this protocol per second; equal to the total packets for this protocol divided by the total number of seconds for this summary period.
Active(Sec)/Flow	Number of seconds from the first packet to the last packet of an expired flow (for example, TCP connection close request [FIN], timeout, and so on) divided by the total flows for this protocol for this summary period.
Idle(Sec)/Flow	Number of seconds observed from the last packet in each nonexpired flow for this protocol until the time at which this command was entered divided by the total flows for this protocol for this summary period.

Table 2-45 describes the fields in the NetFlow record lines of the display.

Table 2-45 show ip cache verbose flow Field Descriptions in NetFlow Record Display
Field	Description
SrcIf	Interface on which the packet was received.
Port Msk AS	Source port number (displayed in hexadecimal format), IP address mask, and autonomous system number. This field is always set to 0 in MPLS flows.
SrcIPaddress	IP address of the device that transmitted the packet.
DstIf	Interface from where the packet was transmitted.
Port Msk AS	Destination port number (displayed in hexadecimal format), IP address mask, and autonomous system. This field is always set to 0 in MPLS flows.
DstIPaddress	IP address of the destination device.
NextHop	BGP next-hop address. This field is always set to 0 in the MPLS flows.
Pr	IP protocol port number, displayed in hexadecimal format. (Go to http://www.iana.org, Protocol Assignment Number Services, for the latest RFC values.)
TOS	Type of service, displayed in hexadecimal format.
B/Pk	Average number of bytes that are observed for the packets seen for this protocol.
Flgs	TCP flags, shown in hexadecimal format (result of bitwise OR of TCP flags from all packets in the flow).
Pkts	Number of packets in this flow.
Active	Time the flow has been active.
FO	Fragment offset.

Related Commands


Command	Description
ip flow-cache mpls label positions	Enables MPLS-aware NetFlow.
ip route-cache flow	Enables NetFlow switching for IP routing.
show ip cache flow	Displays a summary of the NetFlow cache-flow entries.

Bias-Free Language

Results

Chapter: show cable-diagnostics to show ip cache

show cable-diagnostics tdr

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

show catalyst6000

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

show cdp neighbors

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

show cef interface policy-statistics

Syntax Description

Command Default

Command Default

Command History

Examples

show class-map

Syntax Description

Command Default

Command Default

Command History

Examples

Related Commands

show counters interface

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

show diagnostic

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

show diagnostic cns

Syntax Description

Command Default

Command Default

Command History

Usage Guidelines

Examples

Related Commands

show diagnostic sanity

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

show dot1q-tunnel

Syntax Description

Command Default

Command Default

Command History

Usage Guidelines

Examples

Related Commands

show dot1x