Examples

This example shows to display basic 802.11a network settings:

>  show 802.11a
802.11a Network.................................. Enabled
11nSupport....................................... Enabled
      802.11a Low Band........................... Enabled
      802.11a Mid Band........................... Enabled
      802.11a High Band.......................... Enabled
802.11a Operational Rates
    802.11a 6M Rate.............................. Mandatory
    802.11a 9M Rate.............................. Supported
    802.11a 12M Rate............................. Mandatory
    802.11a 18M Rate............................. Supported
    802.11a 24M Rate............................. Mandatory
    802.11a 36M Rate............................. Supported
    802.11a 48M Rate............................. Supported
    802.11a 54M Rate............................. Supported
802.11n MCS Settings:
    MCS 0........................................ Supported
    MCS 1........................................ Supported
    MCS 2........................................ Supported
    MCS 3........................................ Supported
    MCS 4........................................ Supported
    MCS 5........................................ Supported
    MCS 6........................................ Supported
    MCS 7........................................ Supported
    MCS 8........................................ Supported
    MCS 9........................................ Supported
    MCS 10....................................... Supported
    MCS 11....................................... Supported
    MCS 12....................................... Supported
    MCS 13....................................... Supported
    MCS 14....................................... Supported
    MCS 15....................................... Supported
802.11n Status:
    A-MPDU Tx:
        Priority 0............................... Enabled
        Priority 1............................... Disabled
        Priority 2............................... Disabled
        Priority 3............................... Disabled
        Priority 4............................... Disabled
        Priority 5............................... Disabled
        Priority 6............................... Disabled
        Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mandatory............................ Disabled
CF Poll Request mandatory........................ Disabled
--More-- or (q)uit
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 36
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Fragmentation Threshold.......................... 2346
TI Threshold..................................... -50
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Enabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admission Control (CAC) configuration
Voice AC:
   Voice AC - Admission control (ACM)............ Disabled
   Voice max RF bandwidth........................ 75
   Voice reserved roaming bandwidth.............. 6
   Voice load-based CAC mode..................... Disabled
   Voice tspec inactivity timeout................ Disabled
   Voice Stream-Size............................. 84000
   Voice Max-Streams............................. 2
Video AC:
   Video AC - Admission control (ACM)............ Disabled
   Video max RF bandwidth........................ Infinite
   Video reserved roaming bandwidth.............. 0

This example shows how to display basic 802.11h network settings:

>  show 802.11h
802.11h ......................................... powerconstraint : 0
802.11h ......................................... channelswitch : Disable
802.11h ......................................... channelswitch mode : 0

Examples

The following example shows how to display the 802.11a cleanair configuration:

(Cisco Controller) > show 802.11a cleanair
Clean Air Solution............................... Enabled
Air Quality Settings:
    Air Quality Reporting........................ Enabled
    Air Quality Reporting Period (min)........... 15
    Air Quality Alarms........................... Enabled
    Air Quality Alarm Threshold.................. 35 Interference Device Settings:
    Interference Device Reporting................ Enabled
    Interference Device Types:
        TDD Transmitter.......................... Disabled
        Jammer................................... Disabled
        Continuous Transmitter................... Disabled
        DECT-like Phone.......................... Disabled
        Video Camera............................. Disabled
        WiFi Inverted............................ Disabled
        WiFi Invalid Channel..................... Disabled
        SuperAG.................................. Disabled
        Radar.................................... Disabled
        Canopy................................... Disabled
        WiMax Mobile............................. Disabled
        WiMax Fixed.............................. Disabled
Interference Device Alarms................... Enabled
    Interference Device Types Triggering Alarms:
        TDD Transmitter.......................... Disabled
        Jammer................................... Disabled
        Continuous Transmitter................... Disabled
        DECT-like Phone.......................... Disabled
        Video Camera............................. Disabled
        WiFi Inverted............................ Disabled
        WiFi Invalid Channel..................... Disabled
        SuperAG.................................. Disabled
        Radar.................................... Disabled
        Canopy................................... Disabled
        WiMax Mobile............................. Disabled
        WiMax Fixed.............................. Disabled Additional Clean Air Settings:
    CleanAir Event-driven RRM State.............. Enabled
    CleanAir Driven RRM Sensitivity.............. Medium
    CleanAir Persistent Devices state............ Disabled

Examples

The following example shows how to display a summary of the air quality information for the 802.11a network:

(Cisco Controller) > show 802.11a cleanair air-quality summary
AQ = Air Quality
DFS = Dynamic Frequency Selection
AP Name            Channel 	Avg AQ 	Min AQ 	Interferers 	DFS
------------------ ------- 	------ 	------ 	----------- 	---
CISCO_AP3500			 	 	36			95	 70			0
CISCO_AP3500					40			93	 75			0

Examples

The following example shows how to display worst air quality information for the 802.11a network:

(Cisco Controller) > show 802.11 cleanair air-quality worst
AQ = Air Quality
DFS = Dynamic Frequency Selection
AP Name            Channel 	Avg AQ 	Min AQ 	Interferers 	DFS
------------------ ------- 	------ 	------ 	----------- 	---
CISCO_AP3500			 	 	1			83	 57			3		 5

Examples

The following example shows how to display the device access point for the 802.11a network:

(Cisco Controller) > show 802.11a cleanair device ap AP_3500
DC = Duty Cycle (%)
ISI = Interference Severity Index (1-Low Interference, 100-High Interference)
RSSI  = Received Signal Strength Index (dBm)
DevID = Device ID
No  ClusterID          DevID  Type 	 	 	 	 	 	 AP Name 			 	 	 	 	 ISI  RSSI 	 DC   Channel
--- ------------------ ------ ---------- --------------- ---- ----- ---- -------------
1   c2:f7:40:00:00:03  0x8001 DECT phone 	CISCO_AP3500 	1    -43 	 	 3 	 	 	149,153,157,161
2   c2:f7:40:00:00:51  0x8002 Radar		 	 	 CISCO_AP3500 	1    -81 		 	2 	 	153,157,161,165
3   c2:f7:40:00:00:03  0x8005 Canopy	 	 	 CISCO_AP3500 	2    -62	 	 	2 	 	 153,157,161,165

Examples

The following example shows how to display the information of all the interferers detected by a specified access point for the 802.11a network:

(Cisco Controller) > show 802.11a cleanair device type canopy
DC = Duty Cycle (%)
ISI = Interference Severity Index (1-Low Interference, 100-High Interference)
RSSI  = Received Signal Strength Index (dBm)
DevID = Device ID
No  ClusterID          DevID  Type 	 	 	 	 	 	 AP Name 			 	 	 	 	 ISI  RSSI 	 DC   Channel
--- ------------------ ------ ---------- --------------- ---- ----- ---- -------------
1c2:f7:40:00:00:03  0x8005 Canopy	 	 	 	 	 CISCO_AP3500 	2    -62	 	 	 2 	 	 153,157,161,165

Examples

The following is a sample output of the show 802.11a cu-metrics command:

(Cisco Controller) > show 802.11a cu-metrics AP1
AP Interface Mac:           30:37:a6:c8:8a:50
Measurement Duration:       90sec
 Timestamp               Thu Jan 27 09:08:48 2011
   Channel Utilization stats
   ================
     Picc (50th Percentile)...................... 0
     Pib (50th Percentile)....................... 76
     Picc (90th Percentile)...................... 0
     Pib (90th Percentile)....................... 77
 Timestamp               Thu Jan 27 09:34:34 2011

Examples

The following example shows how to display radio extended configurations:

(Cisco Controller) > show 802.11a extended 
Default 802.11a band radio extended configurations:
    beacon period 300, range 60;
    multicast buffer 45, rate 200;
    RX SOP -80; CCA threshold -90;
AP0022.9090.b618 00:24:97:88:99:60
    beacon period 300, range 60; multicast buffer 45, rate 200;
    RX SOP -80; CCA threshold -77
AP0022.9090.bb3e 00:24:97:88:c5:d0
    beacon period 300, range 0; multicast buffer 0, rate 0;
    RX SOP -80; CCA threshold -0
ironRap.ddbf 00:17:df:36:dd:b0
    beacon period 300, range 0; multicast buffer 0, rate 0;
    RX SOP  -80; CCA threshold -0

The following example shows how to display radio extended configurations and the Rx SOP threshold:

(Cisco Controller) > show 802.11a extended 
Default 802.11a band Radio Extended Configurations:
    Beacon period: 100, range: 0 (AUTO);
    Multicast buffer: 0 (AUTO), rate: 0 (AUTO);
    RX SOP threshold: -76; CCA threshold: 0 (AUTO);

AP3600-XALE3  34:a8:4e:6a:7b:00
    Beacon period: 100, range: 0 (AUTO);
    Multicast buffer: 0 (AUTO), rate: 0 (AUTO);
    RX SOP threshold: -76; CCA threshold: 0 (AUTO);

Examples

This example shows how to display the media-stream configuration:

> show 802.11a media-stream rrc
Multicast-direct................................. Enabled
Best Effort...................................... Disabled
Video Re-Direct.................................. Enabled
Max Allowed Streams Per Radio.................... Auto
Max Allowed Streams Per Client................... Auto
Max Video Bandwidth.............................. 0
Max Voice Bandwidth.............................. 75
Max Media Bandwidth.............................. 85
Min PHY Rate..................................... 6000
Max Retry Percentage............................. 80

Examples

The following example shows how to display the automatic channel assignment configuration and statistics:

(Cisco Controller) > show advanced 802.11a channel
Automatic Channel Assignment
  Channel Assignment Mode........................ AUTO
  Channel Update Interval........................ 600 seconds [startup]
  Anchor time (Hour of the day).................. 0
  Channel Update Contribution.................... SNI.
  Channel Assignment Leader...................... 00:1a:6d:dd:1e:40
  Last Run....................................... 129 seconds ago
  DCA Sensitivity Level: ...................... STARTUP (5 dB)
  DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
    Minimum...................................... unknown
    Average...................................... unknown
    Maximum...................................... unknown
  Channel Dwell Times
    Minimum...................................... unknown
    Average...................................... unknown
    Maximum...................................... unknown
  Auto-RF Allowed Channel List................... 36,40,44,48,52,56,60,64,149,
    ............................................. 153,157,161
  Auto-RF Unused Channel List.................... 100,104,108,112,116,132,136,
    ............................................. 140,165,190,196
  DCA Outdoor AP option.......................... Enabled

Examples

The following example shows how to display the statistics for coverage hole detection:

(Cisco Controller) > show advanced 802.11a coverage
Coverage Hole Detection
  802.11a Coverage Hole Detection Mode........... Enabled
  802.11a Coverage Voice Packet Count............ 100 packets
  802.11a Coverage Voice Packet Percentage....... 50%
  802.11a Coverage Voice RSSI Threshold.......... -80 dBm
  802.11a Coverage Data Packet Count............. 50 packets
  802.11a Coverage Data Packet Percentage........ 50%
  802.11a Coverage Data RSSI Threshold........... -80 dBm
  802.11a Global coverage exception level........ 25 %
  802.11a Global client minimum exception lev.... 3 clients

Examples

The following example shows how to display Cisco radio RF group settings:

(Cisco Controller) > show advanced 802.11a group
Radio RF Grouping
  802.11a Group Mode................................... AUTO
  802.11a Group Update Interval........................ 600 seconds
  802.11a Group Leader................................. xx:xx:xx:xx:xx:xx
    802.11a Group Member............................... xx:xx:xx:xx:xx:xx
  802.11a Last Run..................................... 133 seconds ago

Examples

The following is a sample output of the show advanced 802.11b l2roam rf-param command:

(Cisco Controller) > show advanced 802.11b l2roam rf-param

L2Roam 802.11bg RF Parameters.....................
    Config Mode.................................. Default
    Minimum RSSI................................. -85
    Roam Hysteresis.............................. 2
    Scan Threshold............................... -72
    Transition time.............................. 5

Examples

The following example shows how to display 802.11b RF event and performance logging:

(Cisco Controller) > show advanced 802.11b logging
RF Event and Performance Logging
  Channel Update Logging......................... Off
  Coverage Profile Logging....................... Off
  Foreign Profile Logging........................ Off
  Load Profile Logging........................... Off
  Noise Profile Logging.......................... Off
  Performance Profile Logging.................... Off
  TxPower Update Logging......................... Off

Examples

The following example shows how to display the radio monitoring for the 802.11b network:

(Cisco Controller) > show advanced 802.11b monitor
Default 802.11b AP monitoring
  802.11b Monitor Mode........................... enable
  802.11b Monitor Channels....................... Country channels
  802.11b RRM Neighbor Discovery Type............ Transparent
  802.11b AP Coverage Interval................... 180 seconds
  802.11b AP Load Interval....................... 60 seconds
  802.11b AP Noise Interval...................... 180 seconds
  802.11b AP Signal Strength Interval............ 60 seconds

Examples

The following example shows how to display the global configuration and statistics of an 802.11a profile:

(Cisco Controller) > show advanced 802.11 profile global
Default 802.11a AP performance profiles
  802.11a Global Interference threshold.............. 10%
  802.11a Global noise threshold..................... -70 dBm
  802.11a Global RF utilization threshold............ 80%
  802.11a Global throughput threshold................ 1000000 bps
  802.11a Global clients threshold................... 12 clients
  802.11a Global coverage threshold.................. 12 dB
  802.11a Global coverage exception level............ 80%
  802.11a Global client minimum exception lev........ 3 clients

The following example shows how to display the configuration and statistics of a specific access point profile:

(Cisco Controller) >  show advanced 802.11 profile AP1
Cisco AP performance profile not customized

This response indicates that the performance profile for this lightweight access point is using the global defaults and has not been individually configured.

Examples

The following example shows how to display the configuration and statistics of the 802.11a network settings:

(Cisco Controller) > show advanced 802.11 receiver
802.11a Receiver Settings
  RxStart   : Signal Threshold........................... 15
  RxStart   : Signal Lamp Threshold...................... 5
  RxStart   : Preamble Power Threshold................... 2
  RxReStart : Signal Jump Status......................... Enabled
  RxReStart : Signal Jump Threshold...................... 10
  TxStomp : Low RSSI Status.............................. Enabled
  TxStomp : Low RSSI Threshold........................... 30
  TxStomp : Wrong BSSID Status........................... Enabled
  TxStomp : Wrong BSSID Data Only Status................. Enabled
  RxAbort : Raw Power Drop Status........................ Disabled
  RxAbort : Raw Power Drop Threshold..................... 10
  RxAbort : Low RSSI Status.............................. Disabled
  RxAbort : Low RSSI Threshold........................... 0
  RxAbort : Wrong BSSID Status........................... Disabled
  RxAbort : Wrong BSSID Data Only Status................. Disabled

Examples

The following example shows how to display a summary of the 802.11b access point settings:

(Cisco Controller) > show advanced 802.11b summary
AP Name      MAC Address        Admin State  Operation State   Channel TxPower
------------ ------------------ ------------ ----------------- ------- --------
CJ-1240      00:21:1b:ea:36:60    ENABLED          UP           161      1( )
CJ-1130      00:1f:ca:cf:b6:60    ENABLED          UP           56*      1(*)

Note	An asterisk (*) next to a channel number or power level indicates that it is being controlled by the global algorithm settings.

Examples

The following example shows how to display the configuration and statistics of the 802.11b transmit power cost:

(Cisco Controller) > show advanced 802.11b txpower
Automatic Transmit Power Assignment
  Transmit Power Assignment Mode.................. AUTO
  Transmit Power Update Interval.................. 600 seconds
  Transmit Power Threshold........................ -65 dBm
  Transmit Power Neighbor Count................... 3 APs
  Transmit Power Update Contribution.............. SN.
  Transmit Power Assignment Leader................ xx:xx:xx:xx:xx:xx
  Last Run........................................ 384 seconds ago

Examples

The following example shows how to display the backup controller information:

(Cisco Controller) >
show advanced backup-controller
AP primary Backup Controller ....................  controller 10.10.10.10
AP secondary Backup Controller ..................  0.0.0.0

Examples

The following example shows how to display the client auto handoff mode after excessive retries:

(Cisco Controller) >show advanced client-handoff
Client auto handoff after retries................  130

Examples

The following example shows how to view the state of over-the-air frame padding:

(Cisco Controller) > show advanced dot11-padding
dot11-padding.................................... Disabled

Examples

The following example shows how to display the EAP settings:

(Cisco Controller) > show advanced eap
EAP-Identity-Request Timeout (seconds)........... 1
EAP-Identity-Request Max Retries................. 20
EAP Key-Index for Dynamic WEP.................... 0
EAP Max-Login Ignore Identity Response........... enable
EAP-Request Timeout (seconds).................... 1
EAP-Request Max Retries.......................... 20
EAPOL-Key Timeout (milliseconds)................. 1000
EAPOL-Key Max Retries............................ 2

Examples

The following example shows how to display the advanced HotSpot parameters:

(Cisco Controller) >show advanced hotspot
ANQP 4-way state................................. Disabled
GARP Broadcast state: ........................... Enabled
GAS request rate limit .......................... Disabled
ANQP comeback delay in TUs(TU=1024usec).......... 50

Examples

The following example shows how to display the maximum 802.1X sessions per access point:

(Cisco Controller) >show advanced max-1x-sessions
Max 802.1x session per AP at a given time........ 0

Examples

The following example shows how to display the probe settings for the controller:

 (Cisco Controller) >show advanced probe
Probe request filtering.......................... Enabled
Probes fwd to controller per client per radio.... 12
Probe request rate-limiting interval............. 100 msec
 

Examples

The following example shows how to display the switch control path rate limiting mode:

(Cisco Controller) >show advanced rate
Control Path Rate Limiting.......................  Disabled

Examples

The following is a sample output of the show advanced send-disassoc-on-handoff command:

(Cisco Controller) > show advanced send-disassoc-on-handoff
Send Disassociate on Handoff..................... Disabled

Examples

The following is a sample output of the show advanced sip-preferred-call-no command:

(Cisco Controller) > show advanced sip-preferred-call-no
Preferred Call Numbers List
Call Index            Preferred Call No
-----------           ------------------
1                      911
2                      100
3                      101
4                      102
5                      103
6                      104

Examples

The following is a sample output of the show advanced sip-snooping-ports command:

(Cisco Controller) > show advanced sip-snooping-ports
 SIP Call Snoop Ports: 1000 - 2000

Examples

The following example shows how to display switch port statistics mode:

(Cisco Controller) > show advanced statistics
Switch port statistics...........................  Enabled

Examples

The following example shows how to display the system timers setting:

(Cisco Controller) >show advanced timers
Authentication Response Timeout (seconds)........ 10
Rogue Entry Timeout (seconds).................... 1200
AP Heart Beat Timeout (seconds).................. 30
AP Discovery Timeout (seconds)................... 10
AP Local mode Fast Heartbeat (seconds)........... disable
AP flexconnect mode Fast Heartbeat (seconds)........... disable
AP Primary Discovery Timeout (seconds)........... 120

Examples

The following example shows how to display auto-RF information for an access point:

(Cisco Controller) > show ap auto-rf 802.11a AP1
Number Of Slots.................................. 2
AP Name.......................................... AP03
MAC Address...................................... 00:0b:85:01:18:b7
  Radio Type..................................... RADIO_TYPE_80211a
  Noise Information
    Noise Profile................................ PASSED
    Channel 36...................................  -88 dBm
    Channel 40...................................  -86 dBm
    Channel 44...................................  -87 dBm
    Channel 48...................................  -85 dBm
    Channel 52...................................  -84 dBm
    Channel 56...................................  -83 dBm
    Channel 60...................................  -84 dBm
    Channel 64...................................  -85 dBm
  Interference Information
    Interference Profile......................... PASSED
    Channel 36...................................  -66 dBm @  1% busy
    Channel 40................................... -128 dBm @  0% busy
    Channel 44................................... -128 dBm @  0% busy
    Channel 48................................... -128 dBm @  0% busy
    Channel 52................................... -128 dBm @  0% busy
    Channel 56...................................  -73 dBm @  1% busy
    Channel 60...................................  -55 dBm @  1% busy
    Channel 64...................................  -69 dBm @  1% busy
  Rogue Histogram (20/40_ABOVE/40_BELOW)
    Channel 36................................... 16/ 0/ 0
    Channel 40................................... 28/ 0/ 0
    Channel 44...................................  9/ 0/ 0
    Channel 48...................................  9/ 0/ 0
    Channel 52...................................  3/ 0/ 0
    Channel 56...................................  4/ 0/ 0
    Channel 60...................................  7/ 1/ 0
    Channel 64...................................  2/ 0/ 0
  Load Information
    Load Profile................................. PASSED
    Receive Utilization.......................... 0%
    Transmit Utilization......................... 0%
    Channel Utilization.......................... 1%
    Attached Clients............................. 1 clients
  Coverage Information
    Coverage Profile............................. PASSED
    Failed Clients............................... 0 clients
  Client Signal Strengths
    RSSI -100 dBm................................ 0 clients
    RSSI  -92 dBm................................ 0 clients
    RSSI  -84 dBm................................ 0 clients
    RSSI  -76 dBm................................ 0 clients
    RSSI  -68 dBm................................ 0 clients
    RSSI  -60 dBm................................ 0 clients
    RSSI  -52 dBm................................ 0 clients
  Client Signal To Noise Ratios
    SNR    0 dBm................................. 0 clients
    SNR    5 dBm................................. 0 clients
    SNR   10 dBm................................. 0 clients
    SNR   15 dBm................................. 0 clients
    SNR   20 dBm................................. 0 clients
    SNR   25 dBm................................. 0 clients
    SNR   30 dBm................................. 0 clients
    SNR   35 dBm................................. 0 clients
    SNR   40 dBm................................. 0 clients
    SNR   45 dBm................................. 0 clients
  Nearby RADs
    RAD 00:0b:85:01:05:08 slot 0.................  -46 dBm on 10.1.30.170
    RAD 00:0b:85:01:12:65 slot 0.................  -24 dBm on 10.1.30.170
  Channel Assignment Information
    Current Channel Average Energy...............  -86 dBm
    Previous Channel Average Energy..............  -75 dBm
    Channel Change Count.........................  109
    Last Channel Change Time..................... Wed Sep 29 12:53e:34 2004
    Recommended Best Channel..................... 44
  RF Parameter Recommendations
    Power Level.................................. 1
    RTS/CTS Threshold............................ 2347
    Fragmentation Threshold...................... 2346
    Antenna Pattern.............................. 0

Examples

The following example shows how to display the status of the CCX radio management:

(Cisco Controller) >show ap ccx rm AP1240-21ac status
A Radio
Channel Load Request ..................... Disabled 
Noise Histogram Request .................. Disabled
Beacon Request ........................... Disabled
Frame Request ............................ Disabled
Interval ................................. 60
Iteration ................................ 10
G Radio
Channel Load Request ..................... Disabled 
Noise Histogram Request .................. Disabled
Beacon Request ........................... Disabled
Frame Request ............................ Disabled
Interval ................................. 60
Iteration ................................ 10

Examples

The following example shows how to display the CDP status of all access points:

(Cisco Controller) >show ap cdp all
AP CDP State
AP Name             AP CDP State
------------------  ----------
SB_RAP1              enable
SB_MAP1              enable
SB_MAP2              enable
SB_MAP3              enable

The following example shows how to display the CDP status of a specified access point:

(Cisco Controller) >show ap cdp ap-name SB_RAP1
AP CDP State
AP Name             AP CDP State
------------------  ----------
AP CDP State.......................Enabled
AP Interface-Based CDP state
	Ethernet 0.....................Enabled
	Slot 0.........................Enabled
	Slot 1.........................Enabled

The following example shows how to display details about all neighbors using CDP:

(Cisco Controller) >show ap cdp neighbor all
AP Name     AP IP            Neighbor Name       Neighbor IP      Neighbor Port
---------   ---------------  ------------------  --------------  -------------
SB_RAP1     192.168.102.154  sjc14-41a-sw1       192.168.102.2    GigabitEthernet1/0/13
SB_RAP1     192.168.102.154  SB_MAP1             192.168.102.137  Virtual-Dot11Radio0
SB_MAP1     192.168.102.137  SB_RAP1             192.168.102.154  Virtual-Dot11Radio0
SB_MAP1     192.168.102.137  SB_MAP2             192.168.102.138  Virtual-Dot11Radio0
SB_MAP2     192.168.102.138  SB_MAP1             192.168.102.137  Virtual-Dot11Radio1
SB_MAP2     192.168.102.138  SB_MAP3             192.168.102.139  Virtual-Dot11Radio0
SB_MAP3     192.168.102.139  SB_MAP2             192.168.102.138  Virtual-Dot11Radio1

The following example shows how to display details about a specific neighbor with a specified access point using CDP:

(Cisco Controller) >show ap cdp neighbors ap-name SB_MAP2
AP Name      AP IP            Neighbor Name    Neighbor IP      Neighbor Port
-----------  ---------------  ---------------  --------------  -------------
SB_MAP2      192.168.102.138  SB_MAP1          192.168.102.137  Virtual-Dot11Radio1
SB_MAP2      192.168.102.138  SB_MAP3          192.168.102.139  Virtual-Dot11Radio0

The following example shows how to display details about neighbors using CDP:

(Cisco Controller) >show ap cdp neighbors detail SB_MAP2
AP Name:SB_MAP2
AP IP address:192.168.102.138
-------------------------
Device ID: SB_MAP1
Entry address(es): 192.168.102.137
Platform: cisco AIR-LAP1522AG-A-K9  ,  Cap
Interface: Virtual-Dot11Radio0,  Port ID (outgoing port): Virtual-Dot11Radio1
Holdtime : 180 sec
Version :
Cisco IOS Software, C1520 Software (C1520-K9W8-M), Experimental Version 12.4(200
81114:084420) [BLD-v124_18a_ja_throttle.20081114 208] Copyright (c) 1986-2008 by
 Cisco Systems, Inc. Compiled Fri 14-Nov-08 23:08 by
advertisement version: 2
-------------------------
Device ID: SB_MAP3
Entry address(es): 192.168.102.139
Platform: cisco AIR-LAP1522AG-A-K9  ,  Capabilities: Trans-Bridge
Interface: Virtual-Dot11Radio1,  Port ID (outgoing port): Virtual-Dot11Radio0
Holdtime : 180 sec
Version :
Cisco IOS Software, C1520 Software (C1520-K9W8-M), Experimental Version 12.4(200
81114:084420) [BLD-v124_18a_ja_throttle.20081114 208] Copyright (c) 1986-2008 by
 Cisco Systems, Inc. Compiled Fri 14-Nov-08 23:08 by
advertisement version: 2

Examples

The following example shows how to display the available channels for a particular access point:

(Cisco Controller) >show ap channel AP47
	802.11b/g Current Channel ...........1
Allowed Channel List.....................1,2,3,4,5,6,7,8,9,10,11
802.11a Current Channel .................161
Allowed Channel List.....................36,40,44,48,52,56,60,64,100,
.........................................104,108,112,116,132,136,140,
.........................................149,153,157,161

Examples

The following example shows how to display the detailed configuration for an access point:

(Cisco Controller) >show ap config 802.11a AP02
Cisco AP Identifier.............................. 0
Cisco AP Name.................................... AP02
Country code..................................... US  - United States
Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
AP Regulatory Domain............................. Unconfigured
Switch Port Number .............................. 1
MAC Address...................................... 00:0b:85:18:b6:50
IP Address Configuration......................... DHCP
IP Address....................................... 1.100.49.240
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 1.100.49.1
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default-location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch............................. Cisco_32:ab:63
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch...........................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch............................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ........................................... Sniffer
Public Safety ..................................... Global: Disabled, Local: Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W  Version .................................... 7.0.110.6
Boot  Version ................................... 12.4.18.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
Stats Re--More-- or (q)uit
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1142N-A-K9
AP Image......................................... C1140-K9W8-M
IOS Version...................................... 12.4(20100502:031212)
Reset Button..................................... Enabled
AP Serial Number................................. FTX1305S180
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 47 days, 23 h 47 m 47 s
AP LWAPP Up Time................................. 47 days, 23 h 10 m 37 s
Join Date and Time............................... Tue May  4 16:05:00 2010
Join Taken Time.................................. 0 days, 00 h 01 m 37 s
Attributes for Slot  1
    Radio Type................................... RADIO_TYPE_80211n-5
    Radio Subband................................ RADIO_SUBBAND_ALL
    Administrative State ........................ ADMIN_ENABLED
    Operation State ............................. UP
    Radio Role .................................. ACCESS
    CellId ...................................... 0
Station Configuration
      Configuration ............................. AUTOMATIC
      Number Of WLANs ........................... 2
      Medium Occupancy Limit .................... 100
      CFP Period ................................ 4
      CFP MaxDuration ........................... 60
      BSSID ..................................... 00:24:97:88:99:60
Operation Rate Set
        6000 Kilo Bits........................... MANDATORY
        9000 Kilo Bits........................... SUPPORTED
        12000 Kilo Bits.......................... MANDATORY
        18000 Kilo Bits.......................... SUPPORTED
        24000 Kilo Bits.......................... MANDATORY
        36000 Kilo Bits.......................... SUPPORTED
        48000 Kilo Bits.......................... SUPPORTED
        54000 Kilo Bits.......................... SUPPORTED
      MCS Set
        MCS 0.................................... SUPPORTED
        MCS 1.................................... SUPPORTED
        MCS 2.................................... SUPPORTED
        MCS 3.................................... SUPPORTED
        MCS 4.................................... SUPPORTED
        MCS 5.................................... SUPPORTED
        MCS 6.................................... SUPPORTED
        MCS 7.................................... SUPPORTED
        MCS 8.................................... SUPPORTED
        MCS 9.................................... SUPPORTED
        MCS 10................................... SUPPORTED
        MCS 11................................... SUPPORTED
        MCS 12................................... SUPPORTED
        MCS 13................................... SUPPORTED
        MCS 14................................... SUPPORTED
        MCS 15................................... SUPPORTED
      Beacon Period ............................. 100
      Fragmentation Threshold ................... 2346
      Multi Domain Capability Implemented ....... TRUE
      Multi Domain Capability Enabled ........... TRUE
      Country String ............................ US
Multi Domain Capability
      Configuration ............................. AUTOMATIC
      First Chan Num ............................ 36
      Number Of Channels ........................ 21
MAC Operation Parameters
      Configuration ............................. AUTOMATIC
      Fragmentation Threshold ................... 2346
      Packet Retry Limit ........................ 64
Tx Power
      Num Of Supported Power Levels ............. 6
      Tx Power Level 1 .......................... 14 dBm
      Tx Power Level 2 .......................... 11 dBm
      Tx Power Level 3 .......................... 8 dBm
      Tx Power Level 4 .......................... 5 dBm
      Tx Power Level 5 .......................... 2 dBm
      Tx Power Level 6 .......................... -1 dBm
      Tx Power Configuration .................... AUTOMATIC
      Current Tx Power Level .................... 0
Phy OFDM parameters
      Configuration ............................. AUTOMATIC
      Current Channel ........................... 36
      Extension Channel ......................... NONE
      Channel Width.............................. 20 Mhz
      Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
        ......................................... 104,108,112,116,132,136,140,
        ......................................... 149,153,157,161,165
      TI Threshold .............................. -50
      Legacy Tx Beamforming Configuration ....... AUTOMATIC
      Legacy Tx Beamforming ..................... DISABLED
      Antenna Type............................... INTERNAL_ANTENNA
      Internal Antenna Gain (in .5 dBi units).... 6
      Diversity.................................. DIVERSITY_ENABLED
      802.11n Antennas
        Tx
         A....................................... ENABLED
         B....................................... ENABLED
        Rx
         A....................................... ENABLED
         B....................................... ENABLED
         C....................................... ENABLED
Performance Profile Parameters
      Configuration ............................. AUTOMATIC
      Interference threshold..................... 10 %
      Noise threshold............................  -70 dBm
      RF utilization threshold................... 80 %
      Data-rate threshold........................ 1000000 bps
      Client threshold........................... 12 clients
      Coverage SNR threshold..................... 16 dB
      Coverage exception level................... 25 %
      Client minimum exception level............. 3 clients
Rogue Containment Information
    Containment Count............................ 0
CleanAir Management Information
        CleanAir Capable......................... No
Radio Extended Configurations:
        Buffer size ……………………….30
        Data-rate…………………………..0
        Beacon strt ………………………..90 ms
       Rx-Sensitivity SOP threshold ………….. -80 dB
       CCA threshold ……………………. -60 dB

The following example shows how to display the detailed configuration for another access point:

(Cisco Controller) >show ap config 802.11b AP02
Cisco AP Identifier.............................. 0
Cisco AP Name.................................... AP02
AP Regulatory Domain............................. Unconfigured
Switch Port Number .............................. 1
MAC Address...................................... 00:0b:85:18:b6:50
IP Address Configuration......................... DHCP
IP Address....................................... 1.100.49.240
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 1.100.49.1
Cisco AP Location................................ default-location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch............................. Cisco_32:ab:63
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W  Version .................................... 3.1.61.0
Boot  Version ................................... 1.2.59.6
Stats Reporting Period .......................... 180
LED State........................................ Enabled
ILP Pre Standard Switch.......................... Disabled
ILP Power Injector............................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AS-1200
AP Serial Number................................. 044110223A
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot  1
    Radio Type................................... RADIO_TYPE_80211g
    Administrative State ........................ ADMIN_ENABLED
    Operation State ............................. UP
    CellId ...................................... 0
    Station Configuration
      Configuration ............................. AUTOMATIC
      Number Of WLANs ........................... 1
      Medium Occupancy Limit .................... 100
      CFP Period ................................ 4
      CFP MaxDuration ........................... 60
      BSSID ..................................... 00:0b:85:18:b6:50
      Operation Rate Set
        1000 Kilo Bits........................... MANDATORY
        2000 Kilo Bits........................... MANDATORY
        5500 Kilo Bits........................... MANDATORY
        11000 Kilo Bits.......................... MANDATORY
        6000 Kilo Bits........................... SUPPORTED
        9000 Kilo Bits........................... SUPPORTED
        12000 Kilo Bits.......................... SUPPORTED
        18000 Kilo Bits.......................... SUPPORTED
        24000 Kilo Bits.......................... SUPPORTED
        36000 Kilo Bits.......................... SUPPORTED
        48000 Kilo Bits.......................... SUPPORTED
        54000 Kilo Bits.......................... SUPPORTED
      Beacon Period ............................. 100
      DTIM Period ............................... 1
      Fragmentation Threshold ................... 2346
      Multi Domain Capability Implemented ....... TRUE
      Multi Domain Capability Enabled ........... TRUE
      Country String ............................ US
    Multi Domain Capability
      Configuration ............................. AUTOMATIC
      First Chan Num ............................ 1
      Number Of Channels ........................ 11
    MAC Operation Parameters
      Configuration ............................. AUTOMATIC
      RTS Threshold ............................. 2347
      Short Retry Limit ......................... 7
      Long Retry Limit .......................... 4
      Fragmentation Threshold ................... 2346
      Maximum Tx MSDU Life Time ................. 512
      Maximum Rx Life Time....................... 512
    Tx Power
      Num Of Supported Power Levels.............. 5
      Tx Power Level 1 .......................... 17 dBm
      Tx Power Level 2........................... 14 dBm
      Tx Power Level 3........................... 11 dBm
      Tx Power Level 4........................... 8 dBm
      Tx Power Level 5........................... 5 dBm
      Tx Power Configuration..................... CUSTOMIZED
      Current Tx Power Level..................... 5
    Phy OFDM parameters
      Configuration.............................. CUSTOMIZED
      Current Channel............................ 1
      TI Threshold............................... -50
      Legacy Tx Beamforming Configuration ....... CUSTOMIZED
      Legacy Tx Beamforming ..................... ENABLED
      Antenna Type............................... INTERNAL_ANTENNA
      Internal Antenna Gain (in5 dBm units)...... 11
      Diversity.................................. DIVERSITY_ENABLED
    Performance Profile Parameters
      Configuration.............................. AUTOMATIC
      Interference threshold..................... 10%
      Noise threshold............................  -70 dBm
      RF utilization threshold................... 80%
      Data-rate threshold........................ 1000000 bps
      Client threshold........................... 12 clients
      Coverage SNR threshold..................... 12 dB
      Coverage exception level................... 25%
      Client minimum exception level............. 3 clients
    Rogue Containment Information
    Containment Count............................ 0

The following example shows how to display the general configuration of a Cisco access point:

(Cisco Controller) >show ap config general cisco-ap
Cisco AP Identifier.............................. 9
Cisco AP Name.................................... cisco-ap
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. 802.11bg:-A 802.11a:-A
Switch Port Number .............................. 1
MAC Address...................................... 12:12:12:12:12:12
IP Address Configuration......................... DHCP
IP Address....................................... 10.10.10.21
IP NetMask....................................... 255.255.255.0
CAPWAP Path MTU.................................. 1485
Domain...........................................
Name Server......................................
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................ 4404
Primary Cisco Switch IP Address.................. 10.10.10.32
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name....................... 4404
Tertiary Cisco Switch IP Address................. 3.3.3.3
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Global: Disabled, Local: Disabled
AP subMode ...................................... WIPS
Remote AP Debug ................................. Disabled
S/W  Version .................................... 5.1.0.0
Boot  Version ................................... 12.4.10.0
Mini IOS Version ................................ 0.0.0.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. PoE/Low Power (degraded mode)
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1252AG-A-K9
IOS Version...................................... 12.4(10:0)
Reset Button..................................... Enabled
AP Serial Number................................. serial_number
AP Certificate Type.............................. Manufacture Installed
Management Frame Protection Validation........... Enabled (Global MFP Disabled)
AP User Mode..................................... CUSTOMIZED
AP username..................................... maria
AP Dot1x User Mode............................... Not Configured
AP Dot1x username............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 4 days, 06 h 17 m 22 s
AP LWAPP Up Time................................. 4 days, 06 h 15 m 00 s
Join Date and Time............................... Mon Mar 3 06:19:47 2008
Ethernet Port Duplex............................. Auto
Ethernet Port Speed.............................. Auto
AP Link Latency.................................. Enabled
 Current Delay................................... 0 ms
 Maximum Delay................................... 240 ms
 Minimum Delay................................... 0 ms
 Last updated (based on AP Up Time).............. 4 days, 06 h 17 m 20 s
Rogue Detection.................................. Enabled
AP TCP MSS Adjust................................ Disabled
Mesh preferred parent............................ 00:24:13:0f:92:00

Examples

The following example shows how to display global syslog server settings:

(Cisco Controller) >show ap config global 
AP global system logging host.............................. 255.255.255.255

Examples

The following example shows how to display memory core dump information:

(Cisco Controller) >show ap core-dump AP02
Memory core dump is disabled.

Examples

The following example shows how to display the crash file generated by the access point:

(Cisco Controller) >show ap crash-file

Examples

The following example shows how to display the data plane status of all access points:

(Cisco Controller) >show ap data-plane all
Min Data          Data          Max Data     Last
AP Name               Round Trip      Round Trip      Round Trip    Update
------------------  --------------  --------------  --------------  ------
1130                       0.000s          0.000s       0.002s     18:51:23
1240                       0.000s          0.000s       0.000s     18:50:45

Examples

The following example shows how to display the VLAN tagging information for all access points associated to the controller:

(Cisco Controller) >show ap ethernet tag summary

AP Name              Vlan Tag Configuration
------------------   -------
AP2                  7  (Failover to untagged)
charan.AP1140.II     disabled

Examples

The following example shows how to display the event log of an access point:

(Cisco Controller) >show ap eventlog ciscoAP
AP event log download has been initiated
Waiting for download to complete
AP event log download completed.
======================= AP Event log Contents =====================
*Feb 13 11:54:17.146: %CAPWAP-3-CLIENTEVENTLOG: AP event log has been cleared from the contoller 'admin'
*Feb 13 11:54:32.874: *** Access point reloading. Reason: Reload Command ***
*Mar 1 00:00:39.134: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:00:39.174: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:39.211: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:49.947: %CAPWAP-3-CLIENTEVENTLOG: Did not get vendor specific options from DHCP.
...

Examples

The following example shows how to display the inventory of an access point:

(Cisco Controller) >show ap inventory test101
NAME: "test101"    , DESCR: "Cisco Wireless Access Point"
PID: AIR-LAP1131AG-A-K9  ,  VID: V01,  SN: FTX1123T2XX

Examples

The following example shows how to display join information for a specific access point trying to join the controller:

(Cisco Controller) >show ap join stats detailed 00:0b:85:02:0d:20
Discovery phase statistics
- Discovery requests received.......................... 2
- Successful discovery responses sent.................. 2
- Unsuccessful discovery request processing............ 0
- Reason for last unsuccessful discovery attempt....... Not applicable
- Time at last successful discovery attempt............ Aug 21 12:50:23:335
- Time at last unsuccessful discovery attempt.......... Not applicable
Join phase statistics
- Join requests received............................... 1
- Successful join responses sent....................... 1
- Unsuccessful join request processing................. 1
- Reason for last unsuccessful join attempt.............RADIUS authorization is pending for the AP
- Time at last successful join attempt................. Aug 21 12:50:34:481
- Time at last unsuccessful join attempt............... Aug 21 12:50:34:374
Configuration phase statistics
- Configuration requests received...................... 1
- Successful configuration responses sent.............. 1
- Unsuccessful configuration request processing........ 0
- Reason for last unsuccessful configuration attempt... Not applicable
- Time at last successful configuration attempt........ Aug 21 12:50:34:374
- Time at last unsuccessful configuration attempt...... Not applicable
Last AP message decryption failure details
- Reason for last message decryption failure........... Not applicable
Last AP disconnect details
- Reason for last AP connection failure................ Not applicable
Last join error summary
- Type of error that occurred last..................... Lwapp join request rejected
- Reason for error that occurred last.................. RADIUS authorization is pending for the AP
- Time at which the last join error occurred........... Aug 21 12:50:34:374

Examples

The following example shows how to display specific join information for an access point:

(Cisco Controller) >show ap join stats summary 00:0b:85:02:0d:20
Is the AP currently connected to controller.......................... No
Time at which the AP joined this controller last time................ Aug 21 12:50:36:061
Type of error that occurred last..................................... Lwapp join request rejected
Reason for error that occurred last.................................. RADIUS authorization is pending for the AP
Time at which the last join error occurred........................... Aug 21 12:50:34:374

Examples

The following example shows how to display a summary of join information for all access points:

(Cisco Controller) >show ap join stats summary all 
Number of APs.............................................. 4
Base Mac             AP EthernetMac         AP Name         IP Address         Status
00:0b:85:57:bc:c0     00:0b:85:57:bc:c0     AP1130         10.10.163.217     Joined
00:1c:0f:81:db:80     00:1c:63:23:ac:a0     AP1140         10.10.163.216     Not joined
00:1c:0f:81:fc:20     00:1b:d5:9f:7d:b2     AP1             10.10.163.215     Joined
00:21:1b:ea:36:60     00:0c:d4:8a:6b:c1     AP2             10.10.163.214     Not joined

Examples

The following example shows how to get the LED state of all access points:

(Cisco Controller) >show ap led-state all
Global LED State: Enabled (default)

Examples

The following example shows how to display the link encryption status of all access points:

(Cisco Controller) >show ap link-encryption all
             Encryption  Dnstream  Upstream    Last
AP Name           State     Count     Count  Update
------------------  ---  --------  --------  ------
1240                Dis      4406    237553   Never
1130                 En      2484    276308   19:31

Examples

The following example shows how to display current channel-optimized monitor mode settings:

(Cisco Controller) >show ap monitor-mode summary
AP Name            Ethernet MAC       Status     Scanning Channel List
---  -----------------  ---------- ----------------------
AP_004             xx:xx:xx:xx:xx:xx Tracking    1, 6, 11, 4

Examples

The following example shows how to display the access point Packet Capture configurations:

(Cisco Controller) >show ap packet-dump status 
Packet Capture Status............................ Stopped
FTP Server IP Address............................ 0.0.0.0
FTP Server Path..................................
FTP Server Username..............................
FTP Server Password.............................. ********
Buffer Size for Capture.......................... 2048 KB
Packet Capture Time.............................. 45 Minutes
Packet Truncate Length........................... Unspecified
Packet Capture Classifier........................ None

Examples

The following example shows how to display the control packet retransmission parameters of all access points on a network:

(Cisco Controller) >show ap retransmit all
Global control packet retransmit interval: 3 (default)
Global control packet retransmit count: 5 (default)
AP Name             Retransmit Interval  Retransmit count
------------------  -------------------  -------------------
AP_004                   3 (default)      5 (WLC default),5 (AP default)

Examples

The following example shows how to display statistics of an access point for the 802.11b network:

(Cisco Controller) >show ap stats 802.11a Ibiza

Number Of Slots.................................. 2
AP Name.......................................... Ibiza
MAC Address...................................... 44:2b:03:9a:8a:73
Radio Type....................................... RADIO_TYPE_80211a
Stats Information
  Number of Users................................ 0
  TxFragmentCount................................ 84628
  MulticastTxFrameCnt............................ 84628
  FailedCount.................................... 0
  RetryCount..................................... 0
  MultipleRetryCount............................. 0
  FrameDuplicateCount............................ 0
  RtsSuccessCount................................ 1
  RtsFailureCount................................ 0
  AckFailureCount................................ 0
  RxIncompleteFragment........................... 0
  MulticastRxFrameCnt............................ 0
  FcsErrorCount.................................. 20348857
  TxFrameCount................................... 84628
  WepUndecryptableCount.......................... 19907
  TxFramesDropped................................ 0
OEAP WMM Stats :
  Best Effort:
    Tx Frame Count............................... 0
    Tx Failed Frame Count........................ 0
    Tx Expired Count............................. 0
    Tx Overflow Count............................ 0
    Tx Queue Count............................... 0
    Tx Queue Max Count........................... 0
    Rx Frame Count............................... 0
    Rx Failed Frame Count........................ 0
  Background:
    Tx Frame Count............................... 0
    Tx Failed Frame Count........................ 0
    Tx Expired Count............................. 0
    Tx Overflow Count............................ 0
    Tx Queue Count............................... 0
    Tx Queue Max Count........................... 0
    Rx Frame Count............................... 0
    Rx Failed Frame Count........................ 0
  Video:
    Tx Frame Count............................... 0
    Tx Failed Frame Count........................ 0
    Tx Expired Count............................. 0
    Tx Overflow Count............................ 0
    Tx Queue Count............................... 0
    Tx Queue Max Count........................... 0
    Rx Frame Count............................... 0
    Rx Failed Frame Count........................ 0
  Voice:
    Tx Frame Count............................... 0
    Tx Failed Frame Count........................ 0
    Tx Expired Count............................. 0
    Tx Overflow Count............................ 0
    Tx Queue Count............................... 0
    Tx Queue Max Count........................... 0
    Rx Frame Count............................... 0
    Rx Failed Frame Count........................ 0

Rate Limiting Stats:
  Wlan 1:
    Number of Data Packets Received.............. 592
    Number of Data Rx Packets Dropped............ 160
    Number of Data Bytes Received................ 160783
    Number of Data Rx Bytes Dropped.............. 0
    Number of Realtime Packets Received.......... 592
    Number of Realtime Rx Packets Dropped........ 0
    Number of Realtime Bytes Received............ 160783
    Number of Realtime Rx Bytes Dropped.......... 0
    Number of Data Packets Sent.................. 131
    Number of Data Tx Packets Dropped............ 0
    Number of Data Bytes Sent.................... 23436
    Number of Data Tx Bytes Dropped.............. 0
    Number of Realtime Packets Sent.............. 131
    Number of Realtime Tx Packets Dropped........ 0
    Number of Realtime Bytes Sent................ 23436
    Number of Realtime Tx Bytes Dropped.......... 0
Call Admission Control (CAC) Stats
  Voice Bandwidth in use(% of config bw)......... 0
  Voice Roam Bandwidth in use(% of config bw).... 0
    Total channel MT free........................ 0
    Total voice MT free.......................... 0
    Na Direct.................................... 0
    Na Roam...................................... 0
  Video Bandwidth in use(% of config bw)......... 0
  Video Roam Bandwidth in use(% of config bw).... 0
  Total BW in use for Voice(%)................... 0
  Total BW in use for SIP Preferred call(%)...... 0
WMM TSPEC CAC Call Stats
  Total num of voice calls in progress........... 0
  Num of roaming voice calls in progress......... 0
  Total Num of voice calls since AP joined....... 0
  Total Num of roaming calls since AP joined..... 0
  Total Num of exp bw requests received.......... 0
  Total Num of exp bw requests admitted.......... 0
  Num of voice calls rejected since AP joined.... 0
  Num of roam calls rejected since AP joined..... 0
  Num of calls rejected due to insufficent bw.... 0
  Num of calls rejected due to invalid params.... 0
  Num of calls rejected due to PHY rate.......... 0
  Num of calls rejected due to QoS policy........ 0
SIP CAC Call Stats
  Total Num of calls in progress................. 0
  Num of roaming calls in progress............... 0
  Total Num of calls since AP joined............. 0
  Total Num of roaming calls since AP joined..... 0
  Total Num of Preferred calls received.......... 0
  Total Num of Preferred calls accepted.......... 0
  Total Num of ongoing Preferred calls........... 0
  Total Num of calls rejected(Insuff BW)......... 0
  Total Num of roam calls rejected(Insuff BW).... 0
WMM Video TSPEC CAC Call Stats
  Total num of video calls in progress........... 0
  Num of roaming video calls in progress......... 0
  Total Num of video calls since AP joined....... 0
  Total Num of video roaming calls since AP j.... 0
  Num of video calls rejected since AP joined.... 0
  Num of video roam calls rejected since AP j.... 0
  Num of video calls rejected due to insuffic.... 0
  Num of video calls rejected due to invalid .... 0
  Num of video calls rejected due to PHY rate.... 0
  Num of video calls rejected due to QoS poli.... 0
SIP Video CAC Call Stats
  Total Num of video calls in progress........... 0
  Num of video roaming calls in progress......... 0
  Total Num of video calls since AP joined....... 0
  Total Num of video roaming calls since AP j.... 0
  Total Num of video calls rejected(Insuff BW.... 0
  Total Num of video roam calls rejected(Insu.... 0
Band Select Stats
  Num of dual band client ....................... 0
  Num of dual band client added.................. 0
  Num of dual band client expired ............... 0
  Num of dual band client replaced............... 0
  Num of dual band client detected .............. 0
  Num of suppressed client ...................... 0
  Num of suppressed client expired............... 0
  Num of suppressed client replaced.............. 0

Examples

The following example shows how to display a summary of all connected access points:

(Cisco Controller) >show ap summary
Number of APs.................................... 2
Global AP username.............................. user
Global AP Dot1x username........................ Not Configured
Number of APs.................................... 2
Global AP username.............................. user
Global AP Dot1x username........................ Not Configured


 AP Name             Slots  AP Model              Ethernet MAC       Location          Country  IP Address       Clients
------------------  -----  --------------------  -----------------  ----------------  -------  ---------------  -------
AP1140               2     AIR-LAP1142N-A-K9     f0:f7:55:75:f3:29                default location         US   192.168.0.0         0
Access Points using IPv6 transport:
 AP Name    Slots   AP Model           Ethernet MAC       Location         Country     IPv6 Address                 Clients
 ------------------ ----- ------------------------------------- ------------ ------------------ ----- ---------------------------- ------
 AP1040      2    AIR-LAP1042N-A-K9   00:40:96:b9:4b:89   default location  US       2001:DB8:0:1::1                     0

Examples

The following example shows how to display Transmission Control Protocol (TCP) maximum segment size (MSS) information of all access points:

(Cisco Controller) >show ap tcp-mss-adjust all
AP Name            TCP State MSS Size
------------------ --------- -------
AP-1140            enabled   536
AP-1240            disabled  -
AP-1130            disabled  -

Examples

The following example shows how to display BSSIDs of an access point for the 802.11b network:

(Cisco Controller) >show ap wlan 802.11b AP01
Site Name........................................ MY_AP_GROUP1
Site Description................................. MY_AP_GROUP1
WLAN ID          Interface          BSSID
-------         -----------        --------------------------
1               management           00:1c:0f:81:fc:20
2               dynamic              00:1c:0f:81:fc:21

Examples

This example shows how to display client information on an access point:

(Cisco Controller) >show client ap 802.11b AP1
MAC Address        AP Id   Status         WLAN Id    Authenticated
-----------------  ------  -------------  ---------  -------------
xx:xx:xx:xx:xx:xx      1   Associated     1          No

Examples

The following is a sample output of the show client calls active 802.11a command :

(Cisco Controller) > show client calls active 802.11a
Client MAC               Username         Total Call            AP Name         Radio Type
                                         Duration (sec)
--------------------    ---------         ----------       ---------------      ----------
00:09: ef: 02:65:70        abc               45            VJ-1240C-ed45cc        802.11a
00:13: ce: cc: 51:39       xyz               45                AP1130-a416        802.11a
00:40:96: af: 15:15        def               45                AP1130-a416        802.11a
00:40:96:b2:69: df         def               45                AP1130-a416        802.11a
Number of Active Calls ------------------------------------ 4

Examples

The following is a sample output of the show client ccx client-capability command:

(Cisco Controller) >show client ccx client-capability 00:40:96:a8:f7:98
Service Capability.................................. Voice, Streaming(uni-directional) Video, Interactive(bi-directional) Video
Radio Type.......................................... DSSS OFDM(802.11a) HRDSSS(802.11b) ERP(802.11g)
Radio Type.......................................... DSSS
	Radio Channels.................................. 1 2 3 4 5 6 7 8 9 10 11
	Tx Power Mode................................... Automatic
	Rate List(MB)................................... 1.0 2.0
Radio Type.......................................... HRDSSS(802.11b)
	Radio Channels.................................. 1 2 3 4 5 6 7 8 9 10 11
	Tx Power Mode................................... Automatic
	Rate List(MB)................................... 5.5 11.0
Radio Type.......................................... ERP(802.11g)
	Radio Channels.................................. 1 2 3 4 5 6 7 8 9 10 11
	Tx Power Mode................................... Automatic
	Rate List(MB)................................... 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
Are you sure you want to start? (y/N)y Are you sure you want to start? (y/N)

Examples

The following is a sample output of the show client ccx frame-data command:

(Cisco Controller) >show client ccx frame-data
 xx:xx:xx:xx:xx:xx

Examples

The following is a sample output of the show client ccx last-response-status command:

(Cisco Controller) >show client ccx last-response-status
Test Status ........................ Success
Response Dialog Token.............. 87
Response Status.................... Successful
Response Test Type................. 802.1x Authentication Test
Response Time...................... 3476 seconds since system boot

Examples

The following is a sample output of the show client ccx last-test-status command:

(Cisco Controller) >show client ccx last-test-status

Test Type ........................ Gateway Ping Test
Test Status ...................... Pending/Success/Timeout
Dialog Token ..................... 15
Timeout .......................... 15000 ms
Request Time ..................... 1329 seconds since system boot

Examples

The following is a sample output of the show client ccx log-response syslog command:

(Cisco Controller) >show client ccx log-response syslog 00:40:96:a8:f7:98
Tue Jun 26 18:07:48 2007		 		 	Syslog Response LogID=131: Status=Successful
						 	Event Timestamp=0d 00h 19m 42s 278987us
							Client SysLog = ‘<11> Jun 19 11:49:47 unraval13777 Mandatory elements missing in the OID response’
							Event Timestamp=0d 00h 19m 42s 278990us
							Client SysLog = ‘<11> Jun 19 11:49:47 unraval13777 Mandatory elements missing in the OID response’
Tue Jun 26 18:07:48 2007		 		 	Syslog Response LogID=131: Status=Successful
						 	Event Timestamp=0d 00h 19m 42s 278987us
							Client SysLog = ‘<11> Jun 19 11:49:47 unraval13777 Mandatory elements missing in the OID response’
							Event Timestamp=0d 00h 19m 42s 278990us
							Client SysLog = ‘<11> Jun 19 11:49:47 unraval13777 Mandatory elements missing in the OID response’

The following example shows how to display the client roaming log response:

(Cisco Controller) >show client ccx log-response roam 00:40:96:a8:f7:98
Thu Jun 22 11:55:14 2007 	 	Roaming Response LogID=20: Status=Successful
Event Timestamp=0d 00h 00m 13s 322396us						Source BSSID=00:40:96:a8:f7:98
Target BSSID=00:0b:85:23:26:70,						Transition Time=100(ms)					
Transition Reason: Normal roam, poor link						Transition Result: Success
Thu Jun 22 11:55:14 2007 	 	Roaming Response LogID=133: Status=Successful
Event Timestamp=0d 00h 00m 16s 599006us						Source BSSID=00:0b:85:81:06:c2
Target BSSID=00:0b:85:81:06:c2,						Transition Time=3235(ms)						
Transition Reason: Normal roam, poor link						Transition Result: Success
Thu Jun 22 18:28:48 2007 	 	Roaming Response LogID=133: Status=Successful
Event Timestamp=0d 00h 00m 08s 815477us						Source BSSID=00:0b:85:81:06:c2
Target BSSID=00:0b:85:81:06:d2,						Transition Time=3281(ms)						
Transition Reason: First association to WLAN						Transition Result: Success

Examples

The following is a sample output of the show client ccx manufacturer-info command:

(Cisco Controller) >show client ccx manufacturer-info 00:40:96:a8:f7:98
Manufacturer OUI .............................. 00:40:96
Manufacturer ID ............................... Cisco
Manufacturer Model ............................ Cisco Aironet 802.11a/b/g Wireless Adapter
Manufacturer Serial ........................... FOC1046N3SX
Mac Address ................................... 00:40:96:b2:8d:5e
Radio Type .................................... DSSS OFDM(802.11a) HRDSSS(802.11b)
  ERP(802.11g)
Antenna Type .................................. Omni-directional diversity
Antenna Gain .................................. 2 dBi
Rx Sensitivity:
Radio Type ...................................... DSSS
Rx Sensitivity .................................. Rate:1.0 Mbps, MinRssi:-95, MaxRss1:-30
Rx Sensitivity .................................. Rate:2.0 Mbps, MinRssi:-95, MaxRss1:-30
Radio Type ...................................... HRDSSS(802.11b)
Rx Sensitivity .................................. Rate:5.5 Mbps, MinRssi:-95, MaxRss1:-30
Rx Sensitivity .................................. Rate:11.0 Mbps, MinRssi:-95, MaxRss1:-30
Radio Type ...................................... ERP(802.11g)
Rx Sensitivity .................................. Rate:6.0 Mbps, MinRssi:-95, MaxRss1:-30
Rx Sensitivity .................................. Rate:9.0 Mbps, MinRssi:-95, MaxRss1:-30
Rx Sensitivity .................................. Rate:12.0 Mbps, MinRssi:-95, MaxRss1:-30
Rx Sensitivity .................................. Rate:18.0 Mbps, MinRss1:-95, MaxRss1:-30

Examples

The following is a sample output of the show client ccx operating-parameters command:

(Cisco Controller) >show client ccx operating-parameters 00:40:96:b2:8d:5e
Client Mac ......................................... 00:40:96:b2:8d:5e
Radio Type ......................................... OFDM(802.11a)
Radio Type ......................................... OFDM(802.11a)
	Radio Channels ................................. 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140 149 153 157 161 165
	Tx Power Mode .................................. Automatic
	Rate List(MB)................................... 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
Power Save Mode .................................... Normal Power Save
SSID ............................................... wifi
Security Parameters[EAP Method, Credential]......... None
Auth Method ........................................ None
Key Management...................................... None
Encryption ......................................... None
Device Name ........................................ Wireless Network Connection 15
Device Type ........................................ 0
OS Id .............................................. Windows XP
OS Version ......................................... 5.1.6.2600 Service Pack 2
IP Type ............................................ DHCP address
IPv4 Address ....................................... Available
IP Address ......................................... 70.0.4.66
Subnet Mask ........................................ 255.0.0.0
Default Gateway .................................... 70.1.0.1
IPv6 Address ....................................... Not Available
IPv6 Address ....................................... 0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:
IPv6 Subnet Mask ................................... 0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:
DNS Servers ........................................ 103.0.48.0
WINS Servers .......................................
System Name ........................................ URAVAL3777
Firmware Version ................................... 4.0.0.187
Driver Version ..................................... 4.0.0.187

Examples

The following is a sample output of the show client ccx profiles command:

(Cisco Controller) >show client ccx profiles 00:40:96:15:21:ac
Number of Profiles .................................. 1
Current Profile ..................................... 1
Profile ID .......................................... 1
Profile Name ........................................ wifiEAP
SSID ................................................ wifiEAP
Security Parameters [EAP Method, Credential]......... EAP-TLS, Host OS Login Credentials
Auth Method ......................................... EAP
Key Management ...................................... WPA2+CCKM
Encryption .......................................... AES-CCMP
Power Save Mode ..................................... Constantly Awake
Radio Configuration:
Radio Type........................................... DSSS
	Preamble Type.................................... Long preamble
	CCA Method....................................... Energy Detect + Carrier
Detect/Correlation
	Data Retries..................................... 6
	Fragment Threshold............................... 2342
	Radio Channels................................... 1 2 3 4 5 6 7 8 9 10 11
	Tx Power Mode.................................... Automatic
	Rate List (MB)................................... 1.0 2.0
Radio Type........................................... HRDSSS(802.11b)
	Preamble Type.................................... Long preamble
	CCA Method....................................... Energy Detect + Carrier
Detect/Correlation
	Data Retries..................................... 6
	Fragment Threshold............................... 2342
	Radio Channels................................... 1 2 3 4 5 6 7 8 9 10 11
	Tx Power Mode.................................... Automatic
	Rate List(MB).................................... 5.5 11.0
Radio Type........................................... ERP(802.11g)
	Preamble Type.................................... Long preamble
	CCA Method....................................... Energy Detect + Carrier
Detect/Correlation
	Data Retries..................................... 6
	Fragment Threshold............................... 2342
	Radio Channels................................... 1 2 3 4 5 6 7 8 9 10 11
	Tx Power Mode.................................... Automatic
	Rate List (MB)................................... 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
Radio Type........................................... OFDM(802.11a)
	Preamble Type.................................... Long preamble
	CCA Method....................................... Energy Detect + Carrier
Detect/Correlation
	Data Retries..................................... 6
	Fragment Threshold............................... 2342
	Radio Channels................................... 36 40 44 48 52 56 60 64 149 153 157 161 165
	Tx Power Mode.................................... Automatic
	Rate List (MB)................................... 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0

Examples

The following is a sample output of the show client ccx results command:

(Cisco Controller) >show client ccx results xx.xx.xx.xx
dot1x Complete....................................... Success
EAP Method........................................... *1,Host OS Login Credentials
dot1x Status......................................... 255

Examples

The following example shows how to display the client radio management status information:

(Cisco Controller) >show client ccx rm 00:40:96:15:21:ac status

Client Mac Address............................... 00:40:96:15:21:ac
Channel Load Request............................. Enabled
Noise Histogram Request.......................... Enabled
Beacon Request................................... Enabled
Frame Request.................................... Enabled
Interval......................................... 30
Iteration........................................... 10

The following example shows how to display the client radio management load reports:

(Cisco Controller) >show client ccx rm 00:40:96:15:21:ac report chan-load

Channel Load Report
Client Mac Address............................... 00:40:96:ae:53:bc
Timestamp........................................ 788751121
Incapable Flag................................... On
Refused Flag........................................ On
Chan CCA Busy Fraction
-----------------------
1  194
2  86
3  103
4  0
5  178
6  82
7  103
8  95
9  13
10 222
11 75
		

The following example shows how to display the client radio management noise histogram reports:

(Cisco Controller) >show client ccx rm 00:40:96:15:21:ac report noise-hist

Noise Histogram Report
Client Mac Address............................... 00:40:96:15:21:ac
Timestamp........................................ 4294967295
Incapable Flag................................... Off
Refused Flag........................................ Off
Chan RPI0 RPI1 RPI2 RPI3 RPI4 RPI5 RPI6 RPI7

Examples

The following is a sample output of the show client ccx stats-report command:

(Cisco Controller) > show client ccx stats-report 00:0c:41:07:33:a6
Measurement duration = 1
dot11TransmittedFragmentCount       = 1
dot11MulticastTransmittedFrameCount = 2
dot11FailedCount                    = 3
dot11RetryCount                     = 4
dot11MultipleRetryCount             = 5
dot11FrameDuplicateCount            = 6
dot11RTSSuccessCount                = 7
dot11RTSFailureCount                = 8
dot11ACKFailureCount                = 9
dot11ReceivedFragmentCount          = 10
dot11MulticastReceivedFrameCount    = 11
dot11FCSErrorCount                  = 12
dot11TransmittedFrameCount          = 13

Examples

The following is a sample output of the show client detail mac_address command.

(Cisco Controller) > show client detail 01:35:6x:yy:21:00
 Client MAC Address............................... 01:35:6x:yy:21:00
Client Username ................................. test
AP MAC Address................................... 00:11:22:33:44:x0
AP Name.......................................... AP0011.2020.x111
AP radio slot Id................................. 1
Client State..................................... Associated
Client NAC OOB State............................. Access
Wireless LAN Id.................................. 7
Hotspot (802.11u)................................ Not Supported
BSSID............................................ 00:11:22:33:44:xx
Connected For ................................... 28 secs
Channel.......................................... 56
IP Address....................................... 10.0.0.1
Gateway Address.................................. Unknown
Netmask.......................................... Unknown
IPv6 Address..................................... xx20::222:6xyy:zeeb:2233
Association Id................................... 1
Authentication Algorithm......................... Open System
Reason Code...................................... 1
Status Code...................................... 0
Client CCX version............................... No CCX support
Re-Authentication Timeout........................ 1756
QoS Level........................................ Silver
Avg data Rate.................................... 0
Burst data Rate.................................. 0
Avg Real time data Rate.......................... 0
Burst Real Time data Rate........................ 0
802.1P Priority Tag.............................. disabled
CTS Security Group Tag........................... Not Applicable
KTS CAC Capability............................... No
WMM Support...................................... Enabled
  APSD ACs.......................................  BK  BE  VI  VO
Power Save....................................... ON
Current Rate..................................... m7
Supported Rates.................................. 6.0,9.0,12.0,18.0,24.0,36.0,
    ............................................. 48.0,54.0
Mobility State................................... Local
Mobility Move Count.............................. 0
Security Policy Completed........................ No
Policy Manager State............................. SUPPLICANT_PROVISIONING
Policy Manager Rule Created...................... Yes
AAA Override ACL Name............................ android
AAA Override ACL Applied Status.................. Yes
AAA Override Flex ACL Name....................... none
AAA Override Flex ACL Applied Status............. Unavailable
AAA URL redirect................................. https://10.0.0.3:8443/guestportal/gateway?sessionId=0a68aa72000000015272404e&action=nsp
Audit Session ID................................. 0a68aa72000000015272404e
AAA Role Type.................................... none
Local Policy Applied............................. p1
IPv4 ACL Name.................................... none
FlexConnect ACL Applied Status................... Unavailable
IPv4 ACL Applied Status.......................... Unavailable
IPv6 ACL Name.................................... none
IPv6 ACL Applied Status.......................... Unavailable
Layer2 ACL Name.................................. none
Layer2 ACL Applied Status........................ Unavailable
Client Type...................................... SimpleIP
mDNS Status...................................... Enabled
mDNS Profile Name................................ default-mdns-profile
No. of mDNS Services Advertised.................. 0
Policy Type...................................... WPA2
Authentication Key Management.................... 802.1x
Encryption Cipher................................ CCMP (AES)
Protected Management Frame ...................... No
Management Frame Protection...................... No
EAP Type......................................... PEAP
Interface......................................
.. management
VLAN............................................. 0
Quarantine VLAN.................................. 0
Access VLAN...................................... 0
Client Capabilities:
      CF Pollable................................ Not implemented
      CF Poll Request............................ Not implemented
      Short Preamble............................. Not implemented
      PBCC....................................... Not implemented
      Channel Agility............................ Not implemented
      Listen Interval............................ 10
      Fast BSS Transition........................ Not implemented
Client Wifi Direct Capabilities:
      WFD capable................................ No
      Manged WFD capable......................... No
      Cross Connection Capable................... No
      Support Concurrent Operation............... No
Fast BSS Transition Details:
Client Statistics:
      Number of Bytes Received................... 123659
      Number of Bytes Sent....................... 120564
      Number of Packets Received................. 1375
      Number of Packets Sent..................... 276
      Number of Interim-Update Sent.............. 0
      Number of EAP Id Request Msg Timeouts...... 0
      Number of EAP Id Request Msg Failures...... 0
      Number of EAP Request Msg Timeouts......... 2
      Number of EAP Request Msg Failures......... 0
      Number of EAP Key Msg Timeouts............. 0
      Number of EAP Key Msg Failures............. 0
      Number of Data Retries..................... 82
      Number of RTS Retries...................... 0
      Number of Duplicate Received Packets....... 0
      Number of Decrypt Failed Packets........... 0
      Number of Mic Failured Packets............. 0
      Number of Mic Missing Packets.............. 0
      Number of RA Packets Dropped............... 0
      Number of Policy Errors.................... 0
      Radio Signal Strength Indicator............ -51 dBm
      Signal to Noise Ratio...................... 46 dB
Client Rate Limiting Statistics:
      Number of Data Packets Recieved............ 0
      Number of Data Rx Packets Dropped.......... 0
      Number of Data Bytes Recieved.............. 0
      Number of Data Rx Bytes Dropped............ 0
      Number of Realtime Packets Recieved........ 0
      Number of Realtime Rx Packets Dropped...... 0
      Number of Realtime Bytes Recieved.......... 0
      Number of Realtime Rx Bytes Dropped........ 0
      Number of Data Packets Sent................ 0
      Number of Data Tx Packets Dropped.......... 0
      Number of Data Bytes Sent.................. 0
      Number of Data Tx Bytes Dropped............ 0
      Number of Realtime Packets Sent............ 0
      Number of Realtime Tx Packets Dropped...... 0
      Number of Realtime Bytes Sent.............. 0
      Number of Realtime Tx Bytes Dropped........ 0
Nearby AP Statistics:
      AP0022.9090.c545(slot 0)
        antenna0: 26 secs ago.................... -33 dBm
        antenna1: 26 secs ago.................... -35 dBm
      AP0022.9090.c545(slot 1)
        antenna0: 25 secs ago.................... -41 dBm
        antenna1: 25 secs ago.................... -44 dBm
      APc47d.4f3a.35c2(slot 0)
        antenna0: 26 secs ago.................... -30 dBm
        antenna1: 26 secs ago.................... -36 dBm
      APc47d.4f3a.35c2(slot 1)
        antenna0: 24 secs ago.................... -43 dBm
        antenna1: 24 secs ago.................... -45 dBm
DNS Server details:
      DNS server IP ............................. 0.0.0.0
      DNS server IP ............................. 0.0.0.0

Client Dhcp Required:     False
Allowed (URL)IP Addresses
-------------------------
209.165.200.225
209.165.200.226
209.165.200.227
209.165.200.228
209.165.200.229
209.165.200.230
209.165.200.231
209.165.200.232
209.165.200.233
209.165.200.234
209.165.200.235
209.165.200.236
209.165.200.237
209.165.200.238
209.165.201.1
209.165.201.2
209.165.201.3
209.165.201.4
209.165.201.5
209.165.201.6
209.165.201.7
209.165.201.8
209.165.201.9
209.165.201.10

Examples

The following example shows how to display the location calibration summary information:

(Cisco Controller) >show client location-calibration summary
MAC Address Interval
----------- ----------
10:10:10:10:10:10 60
21:21:21:21:21:21 45

Examples

The following example shows how to display the number of probing clients:

(Cisco Controller) >show client probing
Number of Probing Clients........................ 0

Examples

The following example shows how to display a summary of the active clients:

(Cisco Controller) > show client summary
Number of Clients................................ 24
Number of PMIPV6 Clients......................... 200
MAC Address       AP Name           Status        WLAN/GLAN/RLAN Auth Protocol         Port Wired  PMIPV6
----------------- ----------------- ------------- -------------- ---- ---------------- ---- -----		------

00:00:15:01:00:01 NMSP-TalwarSIM1-2 Associated    1              Yes  802.11a          13   No      Yes
00:00:15:01:00:02 NMSP-TalwarSIM1-2 Associated    1              Yes  802.11a          13   No      No
00:00:15:01:00:03 NMSP-TalwarSIM1-2 Associated    1              Yes  802.11a          13   No      Yes
00:00:15:01:00:04 NMSP-TalwarSIM1-2 Associated    1              Yes  802.11a          13   No      No

Examples

The following example shows how to display all clients that are WindowsXP-Workstation device type:

(Cisco Controller) >show client summary WindowsXP-Workstation
Number of Clients in WLAN........................ 0

MAC Address       AP Name    Status        Auth Protocol         Port Wired Mobility Role

----------------- -------- ------------- ----------------        ---------- --------------

Number of Clients with requested device type..... 0

Examples

The following is a sample output of the show client summary guest-lan command:

(Cisco Controller) > show client summary guest-lan 
Number of Clients................................ 1
MAC Address       AP Name      Status         WLAN  Auth   Protocol  Port Wired
-----------       ---------    ----------     ----  ----   --------  ---- -----
00:16:36:40:ac:58  N/A         Associated        1    No      802.3     1   Yes

Examples

The following is a sample output of the show client tsm 802.11a command:

(Cisco Controller) > show client tsm 802.11a xx:xx:xx:xx:xx:xx all
AP Interface MAC: 00:0b:85:01:02:03
Client Interface Mac:               00:01:02:03:04:05
Measurement Duration:               90 seconds
  Timestamp                           1st Jan 2006, 06:35:80
    UpLink Stats
    ================
       Average Delay (5sec intervals)............................35
       Delay less than 10 ms.....................................20
       Delay bet 10 - 20 ms......................................20
       Delay bet 20 - 40 ms......................................20
       Delay greater than 40 ms..................................20
      Total packet Count.........................................80
      Total packet lost count (5sec).............................10
      Maximum Lost Packet count(5sec)............................5
      Average Lost Packet count(5secs)...........................2
    DownLink Stats
    ================
       Average Delay (5sec intervals)............................35
       Delay less than 10 ms.....................................20
       Delay bet 10 - 20 ms......................................20
       Delay bet 20 - 40 ms......................................20
       Delay greater than 40 ms..................................20
      Total packet Count.........................................80
      Total packet lost count (5sec).............................10
      Maximum Lost Packet count(5sec)............................5
      Average Lost Packet count(5secs)...........................2

Examples

The following is a sample output of the show client username command:

(Cisco Controller) > show client username local

MAC Address        AP Name            Status         WLAN  Auth  Protocol          Port  Device Type
-----------------  -----------------  -------------  ----  ----  ----------------  ----  -----------

12:22:64:64:00:01  WEB-AUTH-AP-1      Associated     1     Yes   802.11g            1    Unknown
12:22:64:64:00:02  WEB-AUTH-AP-1      Associated     1     Yes   802.11g            1    Unknown
12:22:64:64:00:03  WEB-AUTH-AP-1      Associated     1     Yes   802.11g            1    Unknown
12:22:64:64:00:04  WEB-AUTH-AP-1      Associated     1     Yes   802.11g            1    Unknown
12:22:64:64:00:05  WEB-AUTH-AP-1      Associated     1     Yes   802.11g            1    Unknown
12:22:64:64:00:06  WEB-AUTH-AP-1      Associated     1     Yes   802.11g            1    Unknown
12:22:64:64:00:07  WEB-AUTH-AP-1      Associated     1     Yes   802.11g            1    Unknown
12:22:64:64:00:08  WEB-AUTH-AP-1      Associated     1     Yes   802.11g            1    Unknown

Examples

The following is a sample output of the show client voice-diag status command:

(Cisco Controller) > show client voice-diag status
Voice Diagnostics Status: FALSE

Examples

The following example shows how to display the detailed information of the access control lists:

(Cisco Controller) >show ipv6 acl detailed acl6
Rule Index....................................... 1
Direction........................................ Any
IPv6 source prefix............................... ::/0
IPv6 destination prefix.......................... ::/0
Protocol......................................... Any
Source Port Range................................ 0-65535
Destination Port Range........................... 0-65535
DSCP............................................. Any
Flow label....................................... 0
Action........................................... Permit
Counter.......................................... 0
Deny Counter................................... 0

Examples

The following is the output of the show ipv6 neighbor-binding summary command:

(Cisco Controller) >show ipv6 neighbor-binding summary
Binding Table has 6 entries, 5 dynamic
Codes: L - Local, S - Static, ND - Neighbor Discovery, DH - DDCP
Preflevel flags (prlvl):
0001:MAC and LLA match     0002:Orig trunk            0004:Orig access
0008:Orig trusted access   0010:Orig trusted trunk    0020:DHCP assigned
0040:Cga authenticated     0080:Cert authenticated    0100:Statically assigned
    IPv6 address                             MAC Address       Port VLAN Type     prlvl age  state     Time left
-- ----------------------------------------  ----------------- ---- ---- -------- ----- ---- --------- ----------
ND  fe80::216:46ff:fe43:eb01                 00:16:46:43:eb:01    1  980 wired     0005    2 REACHABLE  157
ND  fe80::9cf9:b009:b1b4:1ed9                70:f1:a1:dd:cb:d4   AP  980 wireless  0005    2 REACHABLE  157
ND  fe80::6233:4bff:fe05:25ef                60:33:4b:05:25:ef   AP  980 wireless  0005    2 REACHABLE  203
ND  fe80::250:56ff:fe8b:4a8f                 00:50:56:8b:4a:8f   AP  980 wireless  0005    2 REACHABLE  157
ND  2001:410:0:1:51be:2219:56c6:a8ad         70:f1:a1:dd:cb:d4   AP  980 wireless  0005    5 REACHABLE  157
S   2001:410:0:1::9                          00:00:00:00:00:08   AP  980 wireless  0100    1 REACHABLE  205

The following is the output of the show ipv6 neighbor-binding detailed command:

(Cisco Controller) >show ipv6 neighbor-binding detailed mac 60:33:4b:05:25:ef
macDB has 3 entries for mac 60:33:4b:05:25:ef, 3 dynamic
Codes: L - Local, S - Static, ND - Neighbor Discovery, DH - DDCP
Preflevel flags (prlvl):
0001:MAC and LLA match     0002:Orig trunk            0004:Orig access
0008:Orig trusted access   0010:Orig trusted trunk    0020:DHCP assigned
0040:Cga authenticated     0080:Cert authenticated    0100:Statically assigned
    IPv6 address                             MAC Address       Port VLAN Type     prlvl age  state     Time left
-- ----------------------------------------  ----------------- ---- ---- -------- ----- ---- --------- ----------
ND  fe80::6233:4bff:fe05:25ef                60:33:4b:05:25:ef   AP  980 wireless  0009    0 REACHABLE  303
ND  2001:420:0:1:6233:4bff:fe05:25ef         60:33:4b:05:25:ef   AP  980 wireless  0009    0 REACHABLE  300
ND  2001:410:0:1:6233:4bff:fe05:25ef         60:33:4b:05:25:ef   AP  980 wireless  0009    0 REACHABLE  301

The following is the output of the show ipv6 neighbor-binding counters command:

(Cisco Controller) >show ipv6 neighbor-binding counters
Received Messages

NDP Router Solicitation                 6
NDP Router Advertisement                19
NDP Neighbor Solicitation               557
NDP Neighbor Advertisement              48
NDP Redirect                            0
NDP Certificate Solicit                 0
NDP Certificate Advert                  0
DHCPv6 Solicitation                     0
DHCPv6 Advertisement                    0
DHCPv6 Request                          0
DHCPv6 Reply                            0
DHCPv6 Inform                           0
DHCPv6 Confirm                          0
DHCPv6 Renew                            0
DHCPv6 Rebind                           0
DHCPv6 Release                          0
DHCPv6 Decline                          0
DHCPv6 Reconfigure                      0
DHCPv6 Relay Forward                    0
DHCPv6 Relay Rep                        0

Bridged Messages

NDP Router Solicitation                 6
NDP Router Advertisement                19
NDP Neighbor Solicitation               471
NDP Neighbor Advertisement              16
NDP Redirect                            0
NDP Certificate Solicit                 0
NDP Certificate Advert                  0
DHCPv6 Solicitation                     0
DHCPv6 Advertisement                    0
DHCPv6 Request                          0
DHCPv6 Reply                            0
DHCPv6 Inform                           0
DHCPv6 Confirm                          0
DHCPv6 Renew                            0
DHCPv6 Rebind                           0
DHCPv6 Release                          0
DHCPv6 Decline                          0
DHCPv6 Reconfigure                      0
DHCPv6 Relay Forward                    0
DHCPv6 Relay Rep                        0

NDSUPRRESS Drop counters

total   silent ns_in_out ns_dad unicast multicast internal
------------------------------------------------------------------------
0       0       0       0       0       0       0

SNOOPING Drop counters

Dropped Msgs            total   silent  internal CGA_vfy  RSA_vfy  limit  martian  martian_mac  no_trust  not_auth  stop
--------------------------------------------------------------------------------------------------------------------
NDP RS                          0       0       0       0       0       0       0       0       0       0       0
NDP RA                          0       0       0       0       0       0       0       0       0       0       0
NDP NS                          0       0       0       0       0       0       0       0       0       0       0
NDP NA                          0       0       0       0       0       0       0       0       0       0       0
NDP Redirect                    0       0       0       0       0       0       0       0       0       0       0
NDP CERT SOL                    0       0       0       0       0       0       0       0       0       0       0
NDP CERT ADV                    0       0       0       0       0       0       0       0       0       0       0
DHCPv6 Sol                      0       0       0       0       0       0       0       0       0       0       0
DHCPv6 Adv                      0       0       0       0       0       0       0       0       0       0       0
DHCPv6 Req                      0       0       0       0       0       0       0       0       0       0       0
DHCPv6 Confirm                  0       0       0       0       0       0       0       0       0       0       0
DHCPv6 Renew                    0       0       0       0       0       0       0       0       0       0       0
DHCPv6 Rebind                   0       0       0       0       0       0       0       0       0       0       0
DHCPv6 Reply                    0       0       0       0       0       0       0       0       0       0       0
DHCPv6 Release                  0       0       0       0       0       0       0       0       0       0       0
DHCPv6 Decline                  0       0       0       0       0       0       0       0       0       0       0
DHCPv6 Recfg                    0       0       0       0       0       0       0       0       0       0       0
DHCPv6 Infreq                   0       0       0       0       0       0       0       0       0       0       0
DHCPv6 Relayfwd                 0       0       0       0       0       0       0       0       0       0       0
DHCPv6 Relayreply               0       0       0       0       0       0       0       0       0       0       0

CacheMiss Statistics
        Multicast NS Forwarded
                To STA  0
                To DS   0
        Multicast NS Dropped
                To STA  467
                To DS   467

Multicast NA Statistics
        Multicast NA Forwarded
                To STA  0
                To DS   0
        Multicast NA Dropped
                To STA  0
                To DS   0

(Cisco Controller) > >

Examples

The following example show the output of the show ipv6 ra-guard ap summary command:

(Cisco Controller) >show ipv6 ra-guard ap summary
IPv6 RA Guard on AP..................... Enabled
RA Dropped per client:
MAC Address       AP Name           WLAN/GLAN      Number of RA Dropped
----------------- ----------------- -------------- ---------------------
00:40:96:b9:4b:89 Bhavik_1130_1_p13 2              19
----------------- ----------------- -------------- ---------------------
Total RA Dropped on AP......................      19

The following example shows how to display the RA guard statistics for a controller:

(Cisco Controller) >show ipv6 ra-guard wlc summary
IPv6 RA Guard on WLC.................... Enabled

Examples

The following example displays the output of the show ipv6 summary command:

(Cisco Controller) >show ipv6 summary 
Global Config............................... Enabled
Reachable-lifetime value.................... 30
Stale-lifetime value........................ 300
Down-lifetime value......................... 300
RA Throttling............................... Disabled
RA Throttling allow at-least................ 1
RA Throttling allow at-most................. no-limit
RA Throttling max-through................... 5
RA Throttling throttle-period............... 600
RA Throttling interval-option............... ignore
NS Mulitcast CacheMiss Forwarding........... Enabled
NA Mulitcast Forwarding..................... Enabled
IPv6 Capwap UDP Lite........................ Enabled
Operating System IPv6 state ................ Enabled

Examples

This example shows how to display a summary media-stream clients:

> show media-stream client summary
Number of Clients................................ 1
Client Mac         Stream Name  Stream Type  Radio WLAN  QoS    Status
-----------------  -----------  -----------  ----  ----  ------ -------
00:1a:73:dd:b1:12  mountainview  MC-direct    2.4   2     Video  Admitted

Examples

This example shows how to display media-stream group configuration details:

> show media-stream group detail abc
Media Stream Name................................ abc
Start IP Address................................. 227.8.8.8
End IP Address................................... 227.9.9.9
 RRC Parameters
 Avg Packet Size(Bytes).......................... 1200
 Expected Bandwidth(Kbps)........................ 300
 Policy.......................................... Admit
 RRC re-evaluation............................... periodic
 QoS............................................. Video
 Status.......................................... Multicast-direct
 Usage Priority.................................. 5
 Violation....................................... drop

Examples

This example shows how to display a summary of the media-stream group:

(Cisco Controller) > show media-stream group summary
Stream Name   Start IP       End IP         Operation Status
------------- -------------- -------------- ----------------
abc           227.8.8.8      227.9.9.9      Multicast-direct

Examples

The following example shows how to display a summary format:

(Cisco Controller) >show mesh ap summary
AP Name AP Model             BVI MAC              CERT MAC        Hop    Bridge Group Name
------------------  -------------------  -----------------  ------------------   -----  --
SB_RAP1 AIR-LAP1522AG-A-K9   00:1d:71:0e:d0:00  00:1d:71:0e:d0:00   0      sbox
SB_MAP1 AIR-LAP1522AG-A-K9   00:1d:71:0e:85:00  00:1d:71:0e:85:00   1      sbox
SB_MAP2 AIR-LAP1522AG-A-K9   00:1b:d4:a7:8b:00  00:1b:d4:a7:8b:00   2      sbox
SB_MAP3 AIR-LAP1522AG-A-K9   00:1d:71:0d:ee:00  00:1d:71:0d:ee:00   3      sbox
Number of Mesh APs............................... 4
Number of RAPs................................... 1
Number of MAPs................................... 3

The following example shows how to display settings in a hierarchical (tree) format:

(Cisco Controller) >show mesh ap tree
 =======================================================
||  AP Name [Hop Counter, Link SNR, Bridge Group Name] ||
 =======================================================
[Sector 1]
----------
SB_RAP1[0,0,sbox]
  |-SB_MAP1[1,32,sbox]
    |-SB_MAP2[2,27,sbox]
      |-SB_MAP3[3,30,sbox]
----------------------------------------------------
Number of Mesh APs............................... 4
Number of RAPs................................... 1
Number of MAPs................................... 3
----------------------------------------------------

Examples

The following example shows how to display anti-stranding statistics on all outdoor mesh access points:

(Cisco Controller) >show mesh astools stats
Total No of Aps stranded : 0

The following example shows how to display anti-stranding statistics for access point sb_map1 :

(Cisco Controller) >show mesh astools stats sb_map1
Total No of Aps stranded : 0

Examples

The following example shows how to display the current backhaul:

(Cisco Controller) >show mesh backhaul

If the current backhaul is 5 GHz, the output is as follows:

Basic Basic Attributes for Slot  0
    Radio Type................................... RADIO_TYPE_80211g
    Radio Role................................... DOWNLINK ACCESS
    Administrative State ........................ ADMIN_ENABLED
    Operation State ............................. UP
      Current Tx Power Level .................... 1
If the current backhaul is 2.4 GHz, the output is as follows:
Basic Attributes for Slot  1
    Radio Type................................... RADIO_TYPE_80211a
    Radio Subband................................ RADIO_SUBBAND_ALL
    Radio Role................................... DOWNLINK ACCESS
    Administrative State ........................ ADMIN_ENABLED
    Operation State ............................. UP
      Current Tx Power Level .................... 1
      Current Channel ........................... 165
      Antenna Type............................... EXTERNAL_ANTENNA
      External Antenna Gain (in .5 dBm units).... 0
Current Channel...................................6
Antenna Type......................................Externa_ANTENNA
External Antenna Gain (in .5 dBm units)...........0

Examples

The following example shows how to display a summary of the call admission control settings:

(Cisco Controller) >show mesh cac summary
AP Name              Slot#    Radio  BW Used/Max  Calls
-----------------  -------  -----  -----------  -----
SB_RAP1              0        11b/g   0/23437      0
                     1        11a     0/23437      0
SB_MAP1              0        11b/g   0/23437      0
                     1        11a     0/23437      0
SB_MAP2              0        11b/g   0/23437      0
                     1        11a     0/23437      0
SB_MAP3              0        11b/g   0/23437      0
                     1        11a     0/23437      0

The following example shows how to display the mesh topology and the voice bandwidth used or available:

(Cisco Controller) >show mesh cac bwused voice SB_MAP1
AP Name                Slot#    Radio      BW Used/Max
-------------        -------  -----      -----------
    SB_RAP1              0      11b/g       0/23437
                         1      11a         0/23437
|   SB_MAP1              0      11b/g       0/23437
                         1      11a         0/23437
||  SB_MAP2              0      11b/g       0/23437
                         1      11a         0/23437
||| SB_MAP3              0      11b/g       0/23437
                         1      11a         0/23437

The following example shows how to display the access voice calls in progress in a tree topology:

(Cisco Controller) >show mesh cac access 1524_Map1
    AP Name             Slot#   Radio     Calls
    -------------      -------  -----    -----
    1524_Rap             0      11b/g      0
                         1      11a        0
                         2      11a        0
|   1524_Map1            0      11b/g      0
                         1      11a        0
                         2      11a        0
||  1524_Map2            0      11b/g      0
                         1      11a        0
                         2      11a        0

Examples

The following example shows how to display backhaul client access configuration settings for a mesh access point:

(Cisco Controller) >show mesh client-access
Backhaul with client access status: enabled
Backhaul with client access extended status(3 radio AP): disabled

Examples

The following example shows how to display global mesh configuration settings:

(Cisco Controller) >show mesh config 
Mesh Range....................................... 12000
Mesh Statistics update period.................... 3 minutes
Backhaul with client access status............... disabled
Backhaul with extended client access status...... disabled
Background Scanning State........................ enabled
Backhaul Amsdu State............................. disabled
Mesh Security
   Security Mode................................. EAP
   External-Auth................................. disabled
   Use MAC Filter in External AAA server......... disabled
   Force External Authentication................. disabled
Mesh Alarm Criteria
   Max Hop Count................................. 4
   Recommended Max Children for MAP.............. 10
   Recommended Max Children for RAP.............. 20
   Low Link SNR.................................. 12
   High Link SNR................................. 60
   Max Association Number........................ 10
   Association Interval.......................... 60 minutes
   Parent Change Numbers......................... 3
Parent Change Interval........................ 60 minutes
Mesh Multicast Mode.............................. In-Out
Mesh Full Sector DFS............................. enabled
Mesh Ethernet Bridging VLAN Transparent Mode..... disabled
Mesh DCA channels for serial backhaul APs........ enabled
Mesh Slot Bias................................... enabled
Mesh Convergence Method.......................... standard

Examples

The following example shows how to display global environment summary information:

(Cisco Controller) >show mesh env summary
AP Name             Temperature(C)  Heater   Ethernet  Battery
------------------  --------------  ------   --------  -------
ap1130:5f:be:90      N/A             N/A      DOWN     N/A
AP1242:b2.31.ea      N/A             N/A      DOWN     N/A
AP1131:f2.8d.92      N/A             N/A      DOWN     N/A
AP1131:46f2.98ac     N/A             N/A      DOWN     N/A
ap1500:62:39:70      -36             OFF      UP       N/A

The following example shows how to display an environment summary for an access point:

(Cisco Controller) >show mesh env SB_RAP1
AP Name.......................................... SB_RAP1
AP Model......................................... AIR-LAP1522AG-A-K9
AP Role.......................................... RootAP
Temperature...................................... 21 C, 69 F
Heater........................................... OFF
Backhaul......................................... GigabitEthernet0
GigabitEthernet0 Status.......................... UP
    Duplex....................................... FULL
    Speed........................................ 100
    Rx Unicast Packets........................... 114754
    Rx Non-Unicast Packets....................... 1464
    Tx Unicast Packets........................... 9630
    Tx Non-Unicast Packets....................... 3331
GigabitEthernet1 Status.......................... DOWN
  POE Out........................................ OFF
Battery.......................................... N/A

Examples

The following example shows how to display a neighbor summary of an access point:

(Cisco Controller) >show mesh neigh summary RAP1
AP Name/Radio Mac Channel Rate  Link-Snr  Flags      State
----------------- ------- ----- -------- --------   --------
00:1D:71:0F:CA:00 157      54     6        0x0        BEACON
00:1E:14:48:25:00 157      24     1        0x0        BEACON
MAP1-BB00         157      54     41       0x11       CHILD BEACON

The following example shows how to display the detailed neighbor statistics of an access point:

(Cisco Controller) >show mesh neigh detail RAP1
AP MAC : 00:1E:BD:1A:1A:00 AP Name: HOR1522_MINE06_MAP_S_Dyke
backhaul rate 54
FLAGS : 860 BEACON
worstDv 255, Ant 0, channel 153, biters 0, ppiters 0
Numroutes 0, snr 0, snrUp 8, snrDown 8, linkSnr 8
adjustedEase 0, unadjustedEase 0
txParent 0, rxParent 0
poorSnr 0
lastUpdate 2483353214 (Sun Aug 4 23:51:58 1912)
parentChange 0
Per antenna smoothed snr values: 0 0 0 0
Vector through 00:1E:BD:1A:1A:00

The following table lists the output flags displayed for the show mesh neigh detail command.

Examples

The following example shows how to display channel and SNR details for a designated link path:

(Cisco Controller) >show mesh path mesh-45-rap1
AP Name/Radio Mac Channel Rate  Link-Snr  Flags      State
----------------- ------- ----- -------- --------   --------
MAP1-BB00         157      54     32       0x0       UPDATED NEIGH PARENT BEACON
RAP1              157      54     37       0x0        BEACON

Examples

The following example shows how to display the percentage of packet errors for packets transmitted by the neighbors to a mesh access point:

(Cisco Controller) >show mesh per-stats summary ap_12
Neighbor MAC Address 00:0B:85:5F:FA:F0
Total Packets transmitted:              104833
Total Packets transmitted successfully: 104833
Total Packets retried for transmission: 33028
RTS Attempts:                           0
RTS Success:                            0
Neighbor MAC Address:                   00:0B:85:80:ED:D0
Total Packets transmitted:              0
Total Packets transmitted successfully: 0
Total Packets retried for transmission: 0
Neighbor MAC Address:                   00:17:94:FE:C3:5F
Total Packets transmitted:              0
Total Packets transmitted successfully: 0
Total Packets retried for transmission: 0
RTS Attempts:                           0
RTS Success:                            0

Examples

The following example shows how to view 4.8-GHz public safety settings:

(Cisco Controller) >(Cisco Controller) >show mesh public-safety 
Global Public Safety status: disabled

Examples

The following example shows how to view packet error statistics for access point ap417:

(Cisco Controller) >show mesh security-stats ap417
AP MAC : 00:0B:85:5F:FA:F0
Packet/Error Statistics:
-----------------------------
x Packets 14, Rx Packets 19, Rx Error Packets 0
Parent-Side Statistics:
--------------------------
Unknown Association Requests 0
Invalid Association Requests 0
Unknown Re-Authentication Requests 0
Invalid Re-Authentication Requests 0
Unknown Re-Association Requests 0
Invalid Re-Association Requests 0
Child-Side Statistics:
--------------------------
Association Failures 0
Association Timeouts 0
Association Successes 0
Authentication Failures 0
Authentication Timeouts 0
Authentication Successes 0
Re-Association Failures 0
Re-Association Timeouts 0
Re-Association Successes 0
Re-Authentication Failures 0
Re-Authentication Timeouts 0
Re-Authentication Successes 0

Examples

The following example shows how to display statistics of an access point:

(Cisco Controller) >show mesh stats RAP_AP1
RAP in state Maint
rxNeighReq 759978, rxNeighRsp 568673
txNeighReq 115433, txNeighRsp 759978
rxNeighUpd 8266447 txNeighUpd 693062
tnextchan 0, nextant 0, downAnt 0, downChan 0, curAnts 0
tnextNeigh 0, malformedNeighPackets 244, poorNeighSnr 27901
blacklistPackets 0, insufficientMemory 0
authenticationFailures 0
Parent Changes 1, Neighbor Timeouts 16625

Examples

The following example shows how to display a mobility wireless LAN anchor list:

(Cisco Controller) >show mobility anchor
Mobility Anchor Export List
 WLAN ID     IP Address            Status
 -------     ---------------       ------
 12           192.168.0.15         UP
 GLAN ID     IP Address            Status
 -------     ---------------       -------
 1           192.168.0.9           CNTRL_DATA_PATH_DOWN

Examples

The following example shows how to display the mobility AP list:

Note	The AP name is displayed only with New Mobility. With Old Mobility, the AP name is displayed as Unknown.

(Cisco Controller) >show mobility ap-list
AP Name                       AP Radio MAC address      Controller          Learnt From
---------------------------  -----------------------   ---------------    ----------------
AP30e4.dbc5.38ab               b8:62:1f:e5:33:10         9.7.104.10           Self

Examples

The following example shows how to get a mobility wireless LAN foreign map list:

(Cisco Controller) >show mobility foreign-map wlan 2
Mobility Foreign Map List
 WLAN ID               Foreign MAC Address                 Interface
 -------               -------------------                 ---------
   2                    00:1b:d4:6b:87:20                  dynamic-105

Examples

The following example shows how to display the hash keys of the mobility group members:

(Cisco Controller) >show mobility group member hash
Default Mobility Domain.......................... new-mob

 IP Address      Hash Key
---------------------------------------------------------

 9.2.115.68      a819d479dcfeb3e0974421b6e8335582263d9169

 9.6.99.10       0974421b6e8335582263d9169a819d479dcfeb3e

 9.7.7.7         feb3e0974421b6e8335582263d9169a819d479dc

Examples

The following example shows how to display statistics of the mobility manager:

(Cisco Controller) >show mobility statistics
Global Mobility Statistics
   Rx Errors..................................... 0
   Tx Errors..................................... 0
   Responses Retransmitted....................... 0
   Handoff Requests Received..................... 0
   Handoff End Requests Received................. 0
   State Transitions Disallowed.................. 0
   Resource Unavailable.......................... 0
Mobility Initiator Statistics
   Handoff Requests Sent......................... 0
   Handoff Replies Received...................... 0
   Handoff as Local Received..................... 2
   Handoff as Foreign Received................... 0
   Handoff Denys Received........................ 0
   Anchor Request Sent........................... 0
   Anchor Deny Received.......................... 0
   Anchor Grant Received......................... 0
   Anchor Transfer Received...................... 0
Mobility Responder Statistics
   Handoff Requests Ignored...................... 0
   Ping Pong Handoff Requests Dropped............ 0
   Handoff Requests Dropped...................... 0
   Handoff Requests Denied....................... 0
   Client Handoff as Local....................... 0
   Client Handoff as Foreign  ................... 0
   Client Handoff Inter Group ................... 0
   Anchor Requests Received...................... 0
   Anchor Requests Denied........................ 0
   Anchor Requests Granted....................... 0
   Anchor Transferred............................ 0

Examples

The following is a sample output of the show mobility summary command.

(Cisco Controller) >show mobility summary

Symmetric Mobility Tunneling (current) .......... Disabled
Symmetric Mobility Tunneling (after reboot) ..... Disabled
Mobility Protocol Port........................... 16666
Mobility Security Mode........................... Disabled
Default Mobility Domain.......................... snmp_gui
Multicast Mode .................................. Disabled
Mobility Domain ID for 802.11r................... 0x66bd
Mobility Keepalive Interval...................... 10
Mobility Keepalive Count......................... 3
Mobility Group Members Configured................ 1
Mobility Control Message DSCP Value.............. 0
Controllers configured in the Mobility Group
MAC Address        IP Address       Group Name         Multicast IP 	Status
00:1b:d4:6b:87:20    1.100.163.70     snmp_gui         0.0.0.0	       Up

The following is a sample output of the show mobility summary command with new mobility architecture.

(Cisco Controller) >show mobility summary

Mobility Protocol Port........................... 16666
Default Mobility Domain.......................... Mobility
Multicast Mode .................................. Disabled
Mobility Domain ID for 802.11r................... 0xb348
Mobility Keepalive Interval...................... 10
Mobility Keepalive Count......................... 3
Mobility Group Members Configured................ 3
Mobility Control Message DSCP Value.............. 0

Controllers configured in the Mobility Group
 IP Address  Public IP Address  Group Name     Multicast IP  MAC Address               Status
 9.71.106.2  9.72.106.2         Mobility      0.0.0.0      00:00:00:00:00:00  Control and Data Path Down
 9.71.106.3  9.72.106.3         Mobility      0.0.0.0      00:00:00:00:00:00  Control and Data Path Down
 9.71.106.69 9.72.106.69        Mobility      0.0.0.0      68:ef:bd:8e:5f:20          Up