Supported Access Points

• C9105AX

• C9115AX

• C9120AX

• C9130AX

• C9124AX

• C9136I

• CW9162I

• CW9164I

• CW9166I

Note	C9115AX APs support only scanning and advertising.

Supported Platforms

• Cisco Catalyst 9800-L Wireless Controller

• Cisco Catalyst 9800-CL Wireless Controller

  Note

  In newer C9800-CL platform deployment (Cisco IOS XE 17.15.1 release onwards), choose one of the two App Heavy deployment configurations to allocate additional resources for IoT Orchestrator. Once the C9800-CL node comes up, you must configure the platform resource app-heavy command in the configuration prompt mode before starting the IoT Orchestrator Day 0 deployment. To activate the template, you will need to save and reboot the controller. You cannot install IoT Orchestrator in C9800-CL running small or medium templates. You will need additional resources. Ensure that proper CPU allocation is in place before installing the IoT Orchestrator. To do so, perform the following: Ensure that the C9800-CL VM has the following resources 16 vCPU, 40 GB RAM, and 32 GB disk space. Verify the current CPU allocation using the following command: Device# show platform software cpu alloc CPU alloc information: Control plane cpu alloc: 0-7 Data plane cpu alloc: 8-15 Service plane cpu alloc: 0 Platform plane cpu alloc: 0-7 Slow control plane cpu alloc: Template used: None Based on the Templated used field, the following are the three different scenarios: If the Templated used is CLI-app_heavy, no action needs to be performed and C9800-CL is ready for IoT Orchestrator installation. If the Templated used is None, no template is allocated to C9800-CL. To configure the app-heavy template, issue the following commands: Device# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Device(config)# platform resource app-heavy Please reboot to activate this template Device(config)# Device(config)# end Device# write memory Building configuration... [OK] Device# reload Reload command is being issued on Active unit, this will reload the whole stack Proceed with reload? [confirm] Once the C9800-CL reboots, verify if the template is correctly applied or not using the following command: Device# show platform software cpu alloc CPU alloc information: Control plane cpu alloc: 0-7 Data plane cpu alloc: 14-15 Service plane cpu alloc: 8-13 Platform plane cpu alloc: 0-7 Slow control plane cpu alloc: Template used: CLI-app_heavy If the Templated used is Error, this means that the specified template is configured and C9800-CL does not have the resources necessary to create the CPU allocation. To resolve this after verifying that the resources are allocated to the virtual machine, perform the following: Unconfigure the template. In this example, the CLI-app_heavy template is errored. Device# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Device(config)# no platform resource app-heavy Please reboot to activate this template Device(config)# Device(config)# end Device# write memory Building configuration... [OK] Device# reload Reload command is being issued on Active unit, this will reload the whole stack Proceed with reload? [confirm] Once the C9800-CL reboots, verify that the template is deleted using the following command: Device# show platform software cpu alloc CPU alloc information: Control plane cpu alloc: 0-7 Data plane cpu alloc: 8-15 Service plane cpu alloc: 0 Platform plane cpu alloc: 0-7 Slow control plane cpu alloc: Template used: None Reconfigure the CPU allocation using the app_heavy template by issuing the following commands: Device# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Device(config)# platform resource app-heavy Please reboot to activate this template Device(config)# Device(config)# end Device# write memory Building configuration... [OK] Device# reload Reload command is being issued on Active unit, this will reload the whole stack Proceed with reload? [confirm] Verify if the template is correctly applied after the C9800-CL reboots using the following command: Device# show platform software cpu alloc CPU alloc information: Control plane cpu alloc: 0-7 Data plane cpu alloc: 14-15 Service plane cpu alloc: 8-13 Platform plane cpu alloc: 0-7 Slow control plane cpu alloc: Template used: CLI-app_heavy

• Cisco Catalyst 9800-40 Wireless Controller

• Cisco Catalyst 9800-80 Wireless Controller

• Cisco Catalyst CW9800M Wireless Controller

• Cisco Catalyst CW9800H1 and CW9800H2 Wireless Controllers

Scale Requirements