Table Of Contents
E Commands
email-contact
enable
encryption
end
exit
E Commands
The commands in this chapter apply to the Cisco MDS 9000 Family of multilayer directors and fabric switches. All commands are shown here in alphabetical order regardless of command mode. See the "Command Modes" section to determine the appropriate mode for each command. For more information, refer to the Cisco MDS 9000 Family Configuration Guide.
email-contact
To configure an e-mail contact with the Call Home function, use the email-addr command in Call Home configuration submode. To disable this feature, use the no form of the command.
email-addr email-address
no email-addr email-address
Syntax Description
email-address
|
Configures an e-mail address. Uses a standard e-mail address that does not have any text size restrictions.
|
Defaults
None.
Command Modes
Call Home configuration submode
Command History
Release
|
Modification
|
1.0(2)
|
This command was introduced.
|
Usage Guidelines
None.
Examples
The following example shows how to configure e-mail contact in the Call Home configuration.
Enter configuration commands, one per line. End with CNTL/Z.
switch(config-callhome)# email-contact username@company.com
Related Commands
Command
|
Description
|
callhome
|
Configures the Call Home function.
|
callhome test
|
Sends a dummy test message to the configured destination(s).
|
show callhome
|
Displays configured Call Home information.
|
enable
To enable the Call Home function, use the enable command in Call Home configuration submode. To disable this feature, use the disable command.
enable
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Command Modes
Call Home configuration submode.
Command History
Release
|
Modification
|
1.0(2)
|
This command was introduced.
|
Usage Guidelines
To disable the Call Home function, use the disable command.
Examples
The following example shows how to enable the Call Home function.
Enter configuration commands, one per line. End with CNTL/Z.
switch(config-callhome)# enable
Related Commands
Command
|
Description
|
callhome
|
Configures the Call Home function.
|
callhome test
|
Sends a dummy test message to the configured destination(s).
|
show callhome
|
Displays configured Call Home information.
|
encryption
To configure an encryption algorithm for an IKE protocol policy, use the encryption command. To revert to the default, use the no form of the command.
encryption {3des | aes | des}
no encryption
Syntax Description
3des
|
168-bit DES (3DES)
|
aes
|
128-bit AES-CBC
|
des
|
56-bit DES-CBS
|
Defaults
3des
Command Modes
IKE policy configuration submode.
Command History
Release
|
Modification
|
2.0(1b)
|
This command was introduced.
|
Usage Guidelines
To use this command, the IKE protocol must be enabled using the crypto ike enable command.
Examples
The following example shows how to configure the encryption algorithm for the IKE protocol.
switch(config)# crypto ike domain ipsec
switch(config-ike-ipsec)# policy 1
switch(config-ike-ipsec-policy)# encryption 3des
Related Commands
Command
|
Description
|
crypto ike domain ipsec
|
Enters IKE configuration mode.
|
crypto ike enable
|
Enables the IKE protocol.
|
policy
|
Configures IKE policy parameters.
|
show crypto ike domain ipsec
|
Displays IKE information for the IPsec domain.
|
end
To exit any of the configuration modes and return to EXEC mode, use the end command in configuration mode.
end
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Command Modes
Configuration mode.
Command History
This command was introduced in Cisco MDS SAN-OS Release 1.0(2).
Usage Guidelines
You can also press Ctrl-Z to exit configuration mode.
Examples
The following example changes the name to george. Entering the end command causes the system to exit configuration mode and return to EXEC mode.
switch(config)# hostname george
Related Commands
Command
|
Description
|
exit
|
Exits configuration mode, or any of the configuration modes.
|
exit
To exit any configuration mode or close an active terminal session and terminate the EXEC, use the exit command at the system prompt.
exit
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Command Modes
EXEC and Configuration modes.
Command History
This command was introduced in Cisco MDS SAN-OS Release 1.0(2).
Usage Guidelines
Use the exit command at the EXEC levels to exit the EXEC mode. Use the exit command at the configuration level to return to privileged EXEC mode. Use the exit command in interface configuration mode to return to configuration mode. You also can press Ctrl-Z, or use the end command, from any configuration mode to return to EXEC mode.
Note The exit command is associated with privilege level 0. If you configure AAA authorization for a privilege level greater than 0, this command will not be included in the command set for that privilege level.
Examples
The following example displays an exit from the interface configuration mode for VRRP to return to the interface configuration mode.
switch(config-if-vrrp)# exit
The following example displays an exit from the interface configuration mode to return to the configuration mode.
The following example shows how to exit an active session (log-out).
Related Commands
Command
|
Description
|
end
|
Returns you to EXEC mode.
|