 Feedback
|
Table Of Contents
Unsupported Commands in Cisco IOS Release 15.3(1)S
Address Resolution Protocol (ARP) Commands
Hot Standby Routing Protocol (HSRP) Commands
Privileged EXEC or User EXEC Mode
Multiprotocol Label Switching (MPLS) Commands
Privileged EXEC or User EXEC Mode
Multicast Source Discovery Protocol (MSDP) Commands
Quality of Service (QoS) Commands
Simple Network Management Protocol (SNMP) Commands
Privileged EXEC and User EXEC Mode
Unsupported Commands in Cisco IOS Release 15.3(1)S
This appendix lists some of the command-line interface (CLI) commands that appear when you enter the question mark (?) at the Cisco Metro Ethernet (ME) 3800X and ME 3600X switch prompt but are not supported in this release, either because they are not tested or because of switch hardware limitations. This is not a complete list. The unsupported commands are listed by software feature and command mode or they are listed by command mode under "Other Unsupported Commands."
•
Address Resolution Protocol (ARP) Commands
•
•
•
•
•
•
Access Control List Commands
Privileged EXEC Mode
access-enable [host] [timeout minutes]
access-template
clear access-template .
show arp access-list
Global Configuration Mode
arp access-list
access-list rate-limit acl-index {precedence | mask prec-mask}
access-list dynamic extended
Address Resolution Protocol (ARP) Commands
Global Configuration Mode
arp ip-address hardware-address smds
arp ip-address hardware-address srp-a
arp ip-address hardware-address srp-b
Interface Configuration Mode
arp probe
Hot Standby Routing Protocol (HSRP) Commands
Global Configuration Mode
interface Async
interface BVI
interface Dialer
interface Group-Async
interface Lex
interface Virtual-Template
interface Virtual-Tokenring
IGMP Snooping Commands
Global Configuration Mode
ip igmp snooping source-only-learning
IP Multicast Routing Commands
Privileged EXEC Mode
clear ip dvmrp route commands
debug ip dvmrp commands
The debug ip packet command displays packets received by the switch CPU. It does not display packets that are hardware-switched.
The debug ip mcache command affects packets received by the switch CPU. It does not display packets that are hardware-switched.
The debug ip mpacket [detail] [access-list-number [group-name-or-address] command affects only packets received by the switch CPU. Because most multicast packets are hardware-switched, use this command only when you know that the route will forward the packet to the CPU.
debug ip pim atm
show ip dvmrp route commands
The show ip mcache command displays entries in the cache for those packets that are sent to the switch CPU. Because most multicast packets are switched in hardware without CPU involvement, you can use this command, but multicast packet information is not displayed.
The show ip mpacket commands are supported but are only useful for packets received at the switch CPU. If the route is hardware-switched, the command has no effect because the CPU does not receive the packet and cannot display it.
Global Configuration Mode
All ip dvmrp commands
ip multicast-routing vrf vrf-name
ip pim accept-rp
ip pim register-rate-limit
Interface Configuration Mode
All ip dvmrp commands
ip igmp helper-address ip-address
ip multicast helper-map {group-address | broadcast} {broadcast-address | multicast-address} extended-access-list-number
ip multicast rate-limit {in | out} [video | whiteboard] [group-list access-list] [source-list access-list] kbps
ip multicast ttl-threshold ttl-value (instead, use the ip multicast boundary access-list-number interface configuration command)
ip pim nbma-mode
IP Unicast Routing Commands
Privileged EXEC or User EXEC Mode
clear ip accounting [checkpoint]
clear ip bgp address flap-statistics
show cef [drop | not-cef-switched]
show ip accounting [checkpoint] [output-packets | access-violations]
show ip bgp dampened-paths
show ip bgp inconsistent-as
show ip bgp regexp regular expression
show ipv6 (all)
Global Configuration Mode
ip accounting-list ip-address wildcard
ip accounting-transits count
ip cef traffic-statistics [load-interval seconds] [update-rate seconds]]
ip flow-aggregation
ip flow-cache
ip flow-export
ip gratuitous-arps
ip local
ip reflexive-list
router iso-igrp
router mobile
router odr
Interface Configuration Mode
dampening
ip accounting
ip load-sharing [per-packet]
ip mtu bytes
ip ospf dead-interval minimal hello-multiplier multiplier
ip unnumbered type number
All ip security commands
BGP Router Configuration Mode
default-information originate
neighbor advertise-map
neighbor allowas-in
neighbor default-originate
neighbor description
network backdoor
table-map
Route Map Configuration Mode
match route-type for policy-based routing (PBR)
set automatic-tag
set dampening half-life reuse suppress max-suppress-time
set default interface interface-id [interface-id.....]
set interface interface-id [interface-id.....]
set ip default next-hop ip-address [ip-address.....]
set ip destination ip-address mask
set ip precedence value
set ip qos-group
set metric-type internal
set origin
set metric-type internal
VPN Configuration Mode
All
Multiprotocol Label Switching (MPLS) Commands
Privileged EXEC or User EXEC Mode
debug ip rsvp hello [bfd | detail | stats]
debug ip rsvp sso
debug mpls traffic-eng exp
debug mpls traffic-eng forwarding-adjacency
debug mpls traffic-eng ha
show ip rsvp fast-reroute
show ip rsvp hello [instance | statistics]
show mpls traffic-eng exp
show mpls traffic-eng forwarding-adjacency
Global Configuration Mode
ip rsvp signalling hello {bfd | graceful-restart)
mpls traffic-eng auto-bw
mpls traffic-eng lsp
Interface Configuration Mode
Physical Interfaces
ip rsvp bandwidth {mam | rdm}
ip rsvp signalling hello [bfd | dscp | fast-reroute | graceful-restart | refresh | reroute]
mpls traffic-eng srlg
Tunnel Interfaces
tunnel mpls traffic-eng auto-bw
tunnel mpls traffic-eng backup-bw
tunnel mpls traffic-eng exp
tunnel mpls traffic-eng exp-bundle
tunnel mpls traffic-eng forwarding-adjacency
tunnel mpls traffic-eng path-option dynamic attributes
tunnel mpls traffic-eng path-option explicit name attributes
tunnel mpls traffic-eng path-selection
Routing Configuration Mode
interface auto-template
mpls traffic-eng mesh-group (ISIS mode)
mpls traffic-eng multicast-intact (ISIS mode and OSPF mode)
tunnel destination mesh-group
Multicast Source Discovery Protocol (MSDP) Commands
Privileged EXEC Mode
show access-expression
show exception
show pm LINE
show smf [interface-id]
show subscriber-policy [policy-number]
show template [template-name]
Global Configuration Mode
ip msdp default-peer ip-address | name [prefix-list list] (Because BGP/MBGP is not supported, use the ip msdp peer command instead of this command.)
NetFlow Commands
Global Configuration Mode
ip flow-aggregation cache
ip flow-cache entries
Quality of Service (QoS) Commands
Global Configuration Mode
priority-list
Interface Configuration Mode
priority-group
RADIUS Commands
Global Configuration Mode
aaa authentication feature default enable
aaa authentication feature default line
aaa nas port extended
authentication command bounce-port ignore
authentication command disable-port ignore
radius-server attribute nas-port
radius-server configure
radius-server extended-portnames
Simple Network Management Protocol (SNMP) Commands
Global Configuration Mode
snmp-server enable informs
snmp-server ifindex persist
Spanning Tree Commands
Global Configuration Mode
spanning-tree pathcost method {long | short}
spanning-tree transmit hold-count
Interface Configuration Mode
spanning-tree stack-port
VLAN Commands
Global Configuration Mode
vlan internal allocation policy {ascending | descending}
Global Configuration Mode
vlan internal allocation policy {ascending | descending}
VLAN Configuration Mode
remote-span
Other Unsupported Commands
Privileged EXEC and User EXEC Mode
renew ip dhcp snooping database
test cable-diagnostics prbs
verify
Clear Commands
All clear dot1x commands
clear ip arp inspection
All clear ip dhcp snooping commands
All clear ipv6 commands
Debug Commands
All debug dot1x commands
All debug ip dhcp snooping commands
debug ip verify source packet
All debug platform commands
Show Commands
show archive log
show cable-diagnostics prbs
All show dot1x commands
show ip arp inspection
All show ip dhcp snooping commands
All show ip source binding commands
show ip verify source
All show ipv6 commands
All show platform commands
show table-map
Global Configuration Mode
All dot1x commands
All event manager commands
exception crashinfo
errdisable detect cause dhcp-rate-limit
errdisable recovery cause dhcp-rate-limit
interface tunnel
All ip arp inspection commands
All ip dhcp snooping commands
ip source binding
ip sticky-arp
All macro auto commands
memory reserve critical
service compress-config
Interface Configuration Mode
All dot1x commands
All ip arp inspection commands
All ip dhcp snooping commands
ip sticky-arp ignore
ip verify source [tracking | vlan]
transmit-interface type number