Cisco Unity System Administration Guide (With Microsoft Exchange), Release 4.0(4) - Appendix A: Exiting and Starting the Cisco Unity Software and Server [Cisco Unity]

Table Of Contents

Exiting and Starting the Cisco Unity Software and Server

Exiting the Cisco Unity Software

Shutting Down or Restarting the Cisco Unity Server

Starting the Cisco Unity Software

Exiting and Starting the Cisco Unity Software and Server

The following sections provide instructions on exiting the Cisco Unity software, shutting down and restarting the Cisco Unity server, and starting the Cisco Unity software.

Exiting the Cisco Unity Software

This section provides two procedures for exiting the software: from the Cisco Unity server and from another computer. (For details on the accounts that you use to log on to the Cisco Unity server and the Cisco Unity Status Monitor, see the "About the Accounts That Can Be Used to Administer Cisco Unity" section.)

Caution Do not use Kill av*.* to exit the Cisco Unity software. Kill av*.* does not stop all Cisco Unity services, and may cause problems with upgrades from Cisco Unity version 2.x.

To Exit the Cisco Unity Software from the Cisco Unity Server

Step 1 If the system uses the automated attendant, route all calls to the operator.

Step 2 Log on to Windows on the Cisco Unity server by using either the administration account or an applicable Windows domain account.

Step 3 Right-click the Cisco Unity icon in the status area of the taskbar.

(If the Cisco Unity icon is not in the taskbar, browse to the CommServer directory, and double-click AvCsTrayStatus.exe.)

Step 4 Click Stop Cisco Unity. Cisco Unity stops running when all calls are finished, and an "X" appears in the Cisco Unity icon.

Step 5 Press Ctrl-Alt-Delete, then lock or log off Windows to prevent access by unauthorized users.

To Exit the Cisco Unity Software from Another Computer

Step 1 If the system uses the automated attendant, route all calls to the operator.

Step 2 When the Cisco Unity Status Monitor uses Integrated Windows authentication, do the following sub-steps. Otherwise, proceed to Step 3.

a. Log on to Windows by using either the administration account or an applicable Windows domain account.

b. Start Internet Explorer, and go to http://<Cisco Unity server name>/status.

c. If Internet Explorer prompts you for a user name and password, enter the user name, password, and domain for the administration account or an applicable Windows domain account.

d. Proceed to Step 5.

Step 3 When the Cisco Unity Status Monitor uses Anonymous authentication, do the following:

a. Log on to Windows by using any domain account that has the right to log on locally.

b. Start Internet Explorer, and go to http://<Cisco Unity server name>/status.

Step 4 On the Cisco Unity Log On page, enter the user name, password, and domain for the administration account, or enter the user name, password, and domain for an applicable Windows domain account, and click Log On.

Step 5 In the Cisco Unity Status Monitor, under Shutting Down Cisco Unity, choose a method:

•Cisco Unity stops running after all calls are finished.

•Cisco Unity interrupts calls in progress with a voice message, disconnects all calls, then stops running.

Step 6 Click Shut Down.

Shutting Down or Restarting the Cisco Unity Server

Note Restarting the Cisco Unity server may result in delayed message notification and message waiting indication until MAPI logon to all subscriber mailboxes has been completed. Depending on the size of the subscriber database, it could take several hours to complete the MAPI logon.

If the Cisco Unity system has an expansion chassis or is set up for failover, consider the following before shutting down or restarting the Cisco Unity server:

Expansion chassis connected
to the Cisco Unity server

When both the expansion chassis and the Cisco Unity server are turned off, turn on the expansion chassis before you turn on the server. Otherwise, the server may not detect the voice cards in the expansion chassis.

Cisco Unity failover

•When both servers are running and the active server is shut down, the inactive server becomes active.

•When neither server is running, the first server started becomes the active server.

•When the secondary server is active and configured for automatic failback, and the primary server is also running, the secondary server attempts failback on the failback schedule.

To Shut Down or Restart the Cisco Unity Server

Step 1 Exit the Cisco Unity software, if it is running, by using a procedure in the "Exiting the Cisco Unity Software" section.

Step 2 On the Windows Start menu, click Shut Down.

Step 3 Click Shut Down or Restart.

During a restart, the Cisco Unity software starts automatically.

When Cisco Unity starts successfully, three tones play and a check mark appears in the Cisco Unity icon in the status area of the taskbar.

When Cisco Unity does not start successfully, two tones play and an "X" appears in the Cisco Unity icon in the status area of the taskbar.

Starting the Cisco Unity Software

This section provides two procedures for starting the software: from the Cisco Unity server and from another computer. (For details on the accounts that you use to log on to the Cisco Unity server and the Cisco Unity Status Monitor, see the "About the Accounts That Can Be Used to Administer Cisco Unity" section.)

Cisco Unity is a Windows service that is configured to start automatically when you turn on or restart the server. Do one of the following procedures only if you exited the Cisco Unity software but did not restart the server.

Exchange must be running before you start the Cisco Unity software, whether or not Exchange is installed on the Cisco Unity server:

Exchange on
another server

Exchange must be running on the Exchange server that Cisco Unity connects with.

Exchange on the Cisco Unity server

If you exited Exchange manually but did not restart the Cisco Unity server, start Exchange first. (Exchange starts automatically when you turn on or restart the server.)

If Exchange stops for any reason while Cisco Unity is running, Cisco Unity will continue to take messages.

To Start the Cisco Unity Software from the Cisco Unity Server

Step 1 Log on to Windows on the Cisco Unity server by using either the administration account or an applicable Windows domain account.

Step 2 Right-click the Cisco Unity icon in the status area of the taskbar.

(If the Cisco Unity icon is not in the taskbar, browse to the CommServer directory, and double-click AvCsTrayStatus.exe.)

Step 3 Click Start Cisco Unity.

When Cisco Unity starts successfully, three tones play and a check mark appears in the Cisco Unity icon.

When Cisco Unity does not start successfully, two tones play and an "X" appears in the Cisco Unity icon.

Step 4 Press Ctrl-Alt-Delete, then lock or log off Windows to prevent access by unauthorized users.

Step 5 If the system uses the automated attendant and you routed calls to the operator before you exited the Cisco Unity software, reroute calls to Cisco Unity.

To Start the Cisco Unity Software from Another Computer

Step 1 When the Cisco Unity Status Monitor uses Integrated Windows authentication, do the following sub-steps. Otherwise, proceed to Step 2.

a. Log on to Windows by using either the administration account or an applicable Windows domain account.

b. Start Internet Explorer, and go to http://<Cisco Unity server name>/status.

c. If Internet Explorer prompts you for a user name and password, enter the user name, password, and domain for the administration account or an applicable Windows domain account.

d. Proceed to Step 4.

Step 2 When the Cisco Unity Status Monitor uses Anonymous authentication, do the following:

a. Log on to Windows by using any domain account that has the right to log on locally.

b. Start Internet Explorer, and go to http://<Cisco Unity server name>/status.

Step 3 On the Cisco Unity Log On page, enter the user name, password, and domain for the administration account, or enter the user name, password, and domain for an applicable Windows domain account, and click Log On.

Step 4 In the Cisco Unity Status Monitor, click the System Status icon (the first icon), at the top of the page.

Step 5 Click Start.

Step 6 If the system uses the automated attendant and you routed calls to the operator before you exited the Cisco Unity software, reroute calls to Cisco Unity.