Contents

IP Tunnel MIBs

This module contains information about MIBs used with interfaces and hardware components. The IP Tunnel MIB feature provides a generic MIB for managing all IPv4- and IPv6-related tunnels, as outlined in RFC 4087, IP Tunnel MIB. Tunneling provides a way to encapsulate arbitrary packets inside a transport protocol. A number of tunneling mechanism s specified by Internet Engineering Task Force (IETF) are implemented by Cisco for both IPv4 and IPv6 environments. Various MIBs are available for managing tunnels.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Prerequisites for the IP Tunnel MIB

Configure Simple Network Management Protocol (SNMP) on the router on which the IP Tunnel MIB feature is to be used. See the Configuring the Router to Use SNMP for more information. For more information on configuring an SNMP server, see the "Configuring SNMP Support " chapter of the Cisco IOS Network Management Configuration Guide.

Restrictions for the IP Tunnel MIB

The IP Tunnel MIB feature supports only tunnels that can be created using the interface tunnel command. The IP Tunnel MIB feature does not support Layer 2 Tunnel Protocol (L2TP), Point-to-Point Tunneling Protocol (PPTP), or Multiprotocol Label Switching (MPLS) tunnels.

Information About the IP Tunnel MIB

Benefits of the IP Tunnel MIB

Improved Quality of Networks

Better IP tunnel instrumentation leads to an improvement in the quality of networks and better service delivery. A better quality network allows service providers to deliver a more reliable service.

Increased Reliability

The IP Tunnel MIB allows users of network management systems to set inventory and receive notification about their IP tunnel activity.

The IP Tunnel MIB supports both IPv4 and IPv6 network layers as defined in RFC 3291, and is used to manage IP tunnels implemented in the Cisco IOS software.

The IP Tunnel MIB supports all tunnel types, as well as tunnel creation and destruction capability.

Interoperability with Devices Other Than Cisco Devices

The IP Tunnel MIB works with key network management systems, including those of third-party vendors.

MIB Objects Supported by the IP Tunnel MIB

The following MIB objects are supported by the IP Tunnel MIB feature. For details regarding use of MIB objects, see RFC 4087, IP Tunnel MIB.

Table 1 Objects Supported by the IP Tunnel MIB

MIB Object

Description

tunnelIfEntry

Contains information on a particular configured tunnel. You can use the interface tunnel command to set a value for this object.

tunnelIfEncapsMethod

The encapsulation method used by the tunnel. You can use the tunnel mode command to set a value for this object.

tunnelIfHopLimit

Defines the IPv4 time to live (TTL) or IPv6 hop limit to use in the outer IP header. You can use the tunnel ttl command to set a value for this object.

tunnelIfSecurity

Used by the tunnel to secure the outer IP header. The value ipsec indicates that IPsec is used between the tunnel endpoints for authentication or encryption, or both.

tunnelIfTOS

Used by the tunnel to set the high 6 bits (the differentiated services codepoint) of the IPv4 type of service (ToS) or IPv6 traffic class in the outer IP header. You can use the tunnel tos command to set a value for this object.

tunnelIfFlowLabel

Used to set the IPv6 Flow Label value. This object is supported for tunnels over IPv6. The default value for this object is 0.

tunnelIfAddressType

Shows the type of address in the corresponding tunelIfLocalInetAddress and tunnelIfRemoteInetAddress objects. This object cannot be configured individually through the command-line interface (CLI).

tunnelIfLocalInetAddress

The address of the local endpoint of the tunnel (that is, the source address used in the outer IP header). If the address is unknown, the value is 0.0.0.0 for IPv4 or :: for IPv6. The address type of this object is given by tunnelIfAddressType. You can use the tunnel source command to set a value for this object.

tunnelIfRemoteInetAddress

The address of the remote endpoint of the tunnel (that is, the destination address used in the outer IP header). If the address is unknown or the tunnel is not a point-to-point link (for example, a 6-to-4 tunnel), the value is 0.0.0.0 for tunnels over IPv4 or :: for tunnels over IPv6. The address type of this object is given by tunnelIfAddressType. You can use the tunnel destination command to set a value for this object.

tunnelIfEncapsLimit

Shows the maximum number of additional encapsulations permitted for packets undergoing encapsulation at this node. A value of -1 indicates that no limit is present (except as result of packet size).

tunnelInetConfigEntry

Contains information on a particular configured tunnel. There will be only one entry for multipoint tunnels and for tunnels that have the remote inet address 0.0.0.0 for IPv4 or :: for IPv6. Only generic routing encapsulation (GRE)/IP and GRE/IPv6 tunnels are created through the MIB.

tunnelInetConfigIfIndex

Shows the value of ifIndex corresponding to the tunnel interface. A value of 0 is not legal in the active state and means that the interface index has not yet been assigned.

tunnelInetConfigStatus

Used to create or delete table entries in the MIB table. You can use the interface tunnel to set a value for this object.

tunnelInetConfigStorageType

Indicates the storage type. Only a nonvolatile storage value is supported.

How to Configure SNMP and Use the IP Tunnel MIB

Configuring the Router to Use SNMP


Note

Some of the tasks in this section include examples of the SNMP CLI syntax used to set configuration parameters on the router and to read values from MIB objects on the router. These SNMP CLI syntax examples are taken from a Linux workstation using public domain SNMP tools. The SNMP CLI syntax for your workstation might be different. See the documentation that was provided with your SNMP tools for the correct syntax for your network management workstation.

Before you can use the IP Tunnel MIB feature, you must first configure the router to support SNMP. Perform this task to enable SNMP on the router.
SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    snmp-server community string1 ro

    4.    snmp-server community string2 rw

    5.    end


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example:
    Router> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.

     
    Step 2 configure terminal


    Example:
    Router# configure terminal
     

    Enters global configuration mode.

     
    Step 3 snmp-server community string1 ro


    Example:
    Router(config)# snmp-server community public ro
     

    Sets up the community access string to permit access to SNMP.

    • The string1 argument is a community string that consists of from 1 to 32 alphanumeric characters and functions much like a password, permitting access to the SNMP protocol. Blank spaces are not permitted in the community string.

    • The ro keyword specifies read-only access. SNMP management stations using this string can retrieve MIB objects.

    Note   

    The SNMP community read-only (RO) string for the examples is public. You should use a more complex string for this value in your configuration.

     
    Step 4 snmp-server community string2 rw


    Example:
    Router(config)# snmp-server community private rw
     

    Sets up the community access string to permit access to SNMP.

    • The string2 argument is a community string that consists of from 1 to 32 alphanumeric characters and functions much like a password, permitting access to the SNMP protocol. Blank spaces are not permitted in the community string.

    • The rw keyword specifies read-write access. SNMP management stations using this string can retrieve and modify MIB objects.

    Note   

    The SNMP community read-write (RW) string for the examples is private. You should use a more complex string for this value in your configuration.

     
    Step 5 end


    Example:
    Router(config)# end
     

    Exits the current configuration mode and returns to privileged EXEC mode.

     

    What to Do Next

    To implement the IP Tunnel MIB, you must configure a tunnel. For information on configuring tunnels, see the " Implementing Tunnels " chapter in the Cisco IOS Interface and Hardware Component Configuration Guide.

    To debug or troubleshoot any issues related to configuring the IP Tunnel MIB through SNMP, use the debug snmp tunnel-mib command. For information on this command see Cisco IOS Interface and Hardware Component Command Reference.

    Additional References

    Related Documents

    Related Topic

    Document Title

    SNMP commands, complete command syntax, command reference, command history, defaults, defaults, usage guidelines, and examples

    Cisco IOS Network Management Command Reference

    Configuring SNMP Support

    Cisco IOS Network Management Configuration Guide

    Implementing tunnels

    Cisco IOS Interface and Hardware Component Configuration Guide

    Standards

    Standard

    Title

    No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.

    --

    MIBs

    MIB

    MIBs Link

    IP Tunnel MIB

    To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

    http:/​/​www.cisco.com/​go/​mibs

    RFCs

    RFC

    Title

    RFC 4087

    IP Tunnel MIB

    Technical Assistance

    Description

    Link

    The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

    http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

    Feature Information for the Tunnel MIB

    The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

    Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to . An account on Cisco.com is not required.
    Table 2 Feature Information for the IP Tunnel MIB

    Feature Name

    Releases

    Feature Information

    IP Tunnel MIB

    12.2(33)SRB

    12.2(1st)SY

    12.2(44)SG

    12.2(33)SRD

    15.0(1)M

    Cisco IOS XE 3.1.0SG

    Cisco IOS XE Release 3.9S

    The IP Tunnel MIB provides a generic MIB for managing all IPv4- and IPv6-related tunnels, as outlined in RFC 4087 IP Tunnel MIB.

    IP Tunnel MIBs

    IP Tunnel MIBs

    This module contains information about MIBs used with interfaces and hardware components. The IP Tunnel MIB feature provides a generic MIB for managing all IPv4- and IPv6-related tunnels, as outlined in RFC 4087, IP Tunnel MIB. Tunneling provides a way to encapsulate arbitrary packets inside a transport protocol. A number of tunneling mechanism s specified by Internet Engineering Task Force (IETF) are implemented by Cisco for both IPv4 and IPv6 environments. Various MIBs are available for managing tunnels.

    Finding Feature Information

    Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

    Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

    Prerequisites for the IP Tunnel MIB

    Configure Simple Network Management Protocol (SNMP) on the router on which the IP Tunnel MIB feature is to be used. See the Configuring the Router to Use SNMP for more information. For more information on configuring an SNMP server, see the "Configuring SNMP Support " chapter of the Cisco IOS Network Management Configuration Guide.

    Restrictions for the IP Tunnel MIB

    The IP Tunnel MIB feature supports only tunnels that can be created using the interface tunnel command. The IP Tunnel MIB feature does not support Layer 2 Tunnel Protocol (L2TP), Point-to-Point Tunneling Protocol (PPTP), or Multiprotocol Label Switching (MPLS) tunnels.

    Information About the IP Tunnel MIB

    Benefits of the IP Tunnel MIB

    Improved Quality of Networks

    Better IP tunnel instrumentation leads to an improvement in the quality of networks and better service delivery. A better quality network allows service providers to deliver a more reliable service.

    Increased Reliability

    The IP Tunnel MIB allows users of network management systems to set inventory and receive notification about their IP tunnel activity.

    The IP Tunnel MIB supports both IPv4 and IPv6 network layers as defined in RFC 3291, and is used to manage IP tunnels implemented in the Cisco IOS software.

    The IP Tunnel MIB supports all tunnel types, as well as tunnel creation and destruction capability.

    Interoperability with Devices Other Than Cisco Devices

    The IP Tunnel MIB works with key network management systems, including those of third-party vendors.

    MIB Objects Supported by the IP Tunnel MIB

    The following MIB objects are supported by the IP Tunnel MIB feature. For details regarding use of MIB objects, see RFC 4087, IP Tunnel MIB.

    Table 1 Objects Supported by the IP Tunnel MIB

    MIB Object

    Description

    tunnelIfEntry

    Contains information on a particular configured tunnel. You can use the interface tunnel command to set a value for this object.

    tunnelIfEncapsMethod

    The encapsulation method used by the tunnel. You can use the tunnel mode command to set a value for this object.

    tunnelIfHopLimit

    Defines the IPv4 time to live (TTL) or IPv6 hop limit to use in the outer IP header. You can use the tunnel ttl command to set a value for this object.

    tunnelIfSecurity

    Used by the tunnel to secure the outer IP header. The value ipsec indicates that IPsec is used between the tunnel endpoints for authentication or encryption, or both.

    tunnelIfTOS

    Used by the tunnel to set the high 6 bits (the differentiated services codepoint) of the IPv4 type of service (ToS) or IPv6 traffic class in the outer IP header. You can use the tunnel tos command to set a value for this object.

    tunnelIfFlowLabel

    Used to set the IPv6 Flow Label value. This object is supported for tunnels over IPv6. The default value for this object is 0.

    tunnelIfAddressType

    Shows the type of address in the corresponding tunelIfLocalInetAddress and tunnelIfRemoteInetAddress objects. This object cannot be configured individually through the command-line interface (CLI).

    tunnelIfLocalInetAddress

    The address of the local endpoint of the tunnel (that is, the source address used in the outer IP header). If the address is unknown, the value is 0.0.0.0 for IPv4 or :: for IPv6. The address type of this object is given by tunnelIfAddressType. You can use the tunnel source command to set a value for this object.

    tunnelIfRemoteInetAddress

    The address of the remote endpoint of the tunnel (that is, the destination address used in the outer IP header). If the address is unknown or the tunnel is not a point-to-point link (for example, a 6-to-4 tunnel), the value is 0.0.0.0 for tunnels over IPv4 or :: for tunnels over IPv6. The address type of this object is given by tunnelIfAddressType. You can use the tunnel destination command to set a value for this object.

    tunnelIfEncapsLimit

    Shows the maximum number of additional encapsulations permitted for packets undergoing encapsulation at this node. A value of -1 indicates that no limit is present (except as result of packet size).

    tunnelInetConfigEntry

    Contains information on a particular configured tunnel. There will be only one entry for multipoint tunnels and for tunnels that have the remote inet address 0.0.0.0 for IPv4 or :: for IPv6. Only generic routing encapsulation (GRE)/IP and GRE/IPv6 tunnels are created through the MIB.

    tunnelInetConfigIfIndex

    Shows the value of ifIndex corresponding to the tunnel interface. A value of 0 is not legal in the active state and means that the interface index has not yet been assigned.

    tunnelInetConfigStatus

    Used to create or delete table entries in the MIB table. You can use the interface tunnel to set a value for this object.

    tunnelInetConfigStorageType

    Indicates the storage type. Only a nonvolatile storage value is supported.

    How to Configure SNMP and Use the IP Tunnel MIB

    Configuring the Router to Use SNMP


    Note

    Some of the tasks in this section include examples of the SNMP CLI syntax used to set configuration parameters on the router and to read values from MIB objects on the router. These SNMP CLI syntax examples are taken from a Linux workstation using public domain SNMP tools. The SNMP CLI syntax for your workstation might be different. See the documentation that was provided with your SNMP tools for the correct syntax for your network management workstation.

    Before you can use the IP Tunnel MIB feature, you must first configure the router to support SNMP. Perform this task to enable SNMP on the router.
    SUMMARY STEPS

      1.    enable

      2.    configure terminal

      3.    snmp-server community string1 ro

      4.    snmp-server community string2 rw

      5.    end


    DETAILED STEPS
       Command or ActionPurpose
      Step 1 enable


      Example:
      Router> enable
       

      Enables privileged EXEC mode.

      • Enter your password if prompted.

       
      Step 2 configure terminal


      Example:
      Router# configure terminal
       

      Enters global configuration mode.

       
      Step 3 snmp-server community string1 ro


      Example:
      Router(config)# snmp-server community public ro
       

      Sets up the community access string to permit access to SNMP.

      • The string1 argument is a community string that consists of from 1 to 32 alphanumeric characters and functions much like a password, permitting access to the SNMP protocol. Blank spaces are not permitted in the community string.

      • The ro keyword specifies read-only access. SNMP management stations using this string can retrieve MIB objects.

      Note   

      The SNMP community read-only (RO) string for the examples is public. You should use a more complex string for this value in your configuration.

       
      Step 4 snmp-server community string2 rw


      Example:
      Router(config)# snmp-server community private rw
       

      Sets up the community access string to permit access to SNMP.

      • The string2 argument is a community string that consists of from 1 to 32 alphanumeric characters and functions much like a password, permitting access to the SNMP protocol. Blank spaces are not permitted in the community string.

      • The rw keyword specifies read-write access. SNMP management stations using this string can retrieve and modify MIB objects.

      Note   

      The SNMP community read-write (RW) string for the examples is private. You should use a more complex string for this value in your configuration.

       
      Step 5 end


      Example:
      Router(config)# end
       

      Exits the current configuration mode and returns to privileged EXEC mode.

       

      What to Do Next

      To implement the IP Tunnel MIB, you must configure a tunnel. For information on configuring tunnels, see the " Implementing Tunnels " chapter in the Cisco IOS Interface and Hardware Component Configuration Guide.

      To debug or troubleshoot any issues related to configuring the IP Tunnel MIB through SNMP, use the debug snmp tunnel-mib command. For information on this command see Cisco IOS Interface and Hardware Component Command Reference.

      Additional References

      Related Documents

      Related Topic

      Document Title

      SNMP commands, complete command syntax, command reference, command history, defaults, defaults, usage guidelines, and examples

      Cisco IOS Network Management Command Reference

      Configuring SNMP Support

      Cisco IOS Network Management Configuration Guide

      Implementing tunnels

      Cisco IOS Interface and Hardware Component Configuration Guide

      Standards

      Standard

      Title

      No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.

      --

      MIBs

      MIB

      MIBs Link

      IP Tunnel MIB

      To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

      http:/​/​www.cisco.com/​go/​mibs

      RFCs

      RFC

      Title

      RFC 4087

      IP Tunnel MIB

      Technical Assistance

      Description

      Link

      The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

      http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

      Feature Information for the Tunnel MIB

      The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

      Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to . An account on Cisco.com is not required.
      Table 2 Feature Information for the IP Tunnel MIB

      Feature Name

      Releases

      Feature Information

      IP Tunnel MIB

      12.2(33)SRB

      12.2(1st)SY

      12.2(44)SG

      12.2(33)SRD

      15.0(1)M

      Cisco IOS XE 3.1.0SG

      Cisco IOS XE Release 3.9S

      The IP Tunnel MIB provides a generic MIB for managing all IPv4- and IPv6-related tunnels, as outlined in RFC 4087 IP Tunnel MIB.