- Read Me First
- L2VPN Protocol-Based CLIs
- Any Transport over MPLS
- L2VPN Interworking
- L2VPN Pseudowire Preferential Forwarding
- L2VPN Multisegment Pseudowires
- MPLS Quality of Service
- QoS Policy Support on L2VPN ATM PVPs
- MPLS Pseudowire Status Signaling
- L2VPN VPLS Inter-AS Option B
- IEEE 802.1Q Tunneling (QinQ) for AToM
- Configuring the Managed IPv6 Layer 2 Tunnel Protocol Network Server
- L2VPN Pseudowire Redundancy
- Pseudowire Group Switchover
- L2VPN Pseudowire Switching
- Xconnect as a Client of BFD
- H-VPLS N-PE Redundancy for QinQ Access
- H-VPLS N-PE Redundancy for MPLS Access
- VPLS MAC Address Withdrawal
- Configuring Virtual Private LAN Services
- Routed Pseudo-Wire and Routed VPLS
- VPLS Autodiscovery BGP Based
- N:1 PVC Mapping to PWE with Nonunique VPIs
- QoS Policies for VFI Pseudowires
- VPLS BGP Signaling L2VPN Inter-AS Option A
- VPLS BGP Signaling L2VPN Inter-AS Option B
- Frame Relay over L2TPv3
- Loop-Free Alternate Fast Reroute with L2VPN
Xconnect as a Client of BFD
The Xconnect as a Client of Bidirectional Forwarding Detection (BFD) feature provides a trigger for redundant pseudowire switchover based on BFD’s fast failure detection capabilities.
- Finding Feature Information
- Information About Xconnect as a Client of BFD
- How to Configure Xconnect as a Client of BFD
- Configuration Examples for Xconnect as a Client of BFD
- Additional References
- Feature Information for Xconnect as a Client of BFD
Finding Feature Information
Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
Information About Xconnect as a Client of BFD
Xconnect as a Client of BFD
Redundant pseudowires are deployed to provide fault tolerance and resiliency to L2VPN-backhauled connections. The speed at which a system recovers from failures, especially when scaled to large numbers of pseudowires, is critical to many service providers and service level agreements (SLAs). The configuration of a trigger for redundant pseudowire switchover reduces the time that it takes a large number of pseudowires to failover. A fundamental component of bidirectional forwarding detection (BFD) capability is enabled by fast-failure detection (FFD).
The configuration of this feature refers to a BFD configuration, such as the following (the second URL in the bfd map command is the loopback URL in the monitor peer bfd command):
bfd-template multi-hop mh interval min-tx 200 min-rx 200 multiplier 3 ! bfd map ipv4 10.1.1.0/24 10.1.1.1/32 mh
How to Configure Xconnect as a Client of BFD
Configuring Xconnect as a Client of BFD
Perform this task to configure a trigger for redundant pseudowire switchover.
1.
enable
2.
configure
terminal
4.
encapsulation mpls
5.
monitor peer bfd [local interface
interface-type interface-number]
DETAILED STEPS
Configuration Examples for Xconnect as a Client of BFD
Example: Xconnect as a Client of BFD
Pseudowire Class Configuration
The following example shows pseudowire fast-failure detection enabled for a pseudowire class:
pseudowire-class mpls-ffd encapsulation mpls monitor peer bfd local interface Loopback0
Template Configuration
The following example shows pseudowire fast-failure detection enabled in a template:
template type pseudowire 1 encapsulation mpls monitor peer bfd local interface Ethernet0/1
Interface Configuration
The following example shows pseudowire fast-failure detection enabled for an interface:
interface pseudowire100 encapsulation mpls neighbor 10.10.1.1 21190 monitor peer bfd local interface Ethernet0/1
Additional References
Related Documents
|
Related Topic |
Document Title |
|---|---|
|
Any Transport over MPLS |
Any Transport over MPLS |
|
High Availability for AToM |
AToM Graceful Restart |
|
L2VPN Interworking |
L2VPN Interworking |
|
Layer 2 local switching |
Layer 2 Local Switching |
|
PWE3 MIB |
Pseudowire Emulation Edge-to-Edge MIBs for Ethernet and Frame Relay Services |
|
Packet sequencing |
Any Transport over MPLS (AToM) Sequencing Support |
|
BFD configuration |
Standards
|
Standards |
Title |
|---|---|
|
None |
-- |
MIBs
|
MIBs |
MIBs Link |
|---|---|
|
None |
To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL: |
RFCs
|
RFCs |
Title |
|---|---|
|
None |
-- |
Technical Assistance
|
Description |
Link |
|---|---|
|
The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies. To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds. Access to most tools on the Cisco Support website requires a Cisco.com user ID and password. |
Feature Information for Xconnect as a Client of BFD
The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.|
Feature Name |
Releases |
Feature Information |
|---|---|---|
|
Xconnect as a Client of BFD |
Cisco IOS XE Release 3.8S |
This feature provides fast-failure detection for L2VPN pseudowire redundancy. The following command was introduced: monitor peer bfd. |
Feedback