One of the many challenges faced by customers today is the tracking and blocking denial-of-service (DoS) attacks. Counteracting a DoS attack involves intrusion detection, source tracking, and blocking. This functionality addresses the need for source tracking.

To trace attacks, NetFlow and access control lists (ACLs) have been used. To block attacks, committed access rate (CAR) and ACLs have been used. Support for these features on the Cisco 12000 series Internet router has depended on the type of line card used. Support for these features on the Cisco 7500 series routers depends upon the type of port adapter used. There is, therefore, a need to develop a way to receive information that both traces the source of an attack and is supported on all line cards and port adapters.

Normally, when you identify the host that is subject to a DoS attack, you must determine the network ingress point to effectively block the attack. This process starts at the router closest to the host.

For example, in the figure below, you would start at Router A and try to determine the next upstream router to examine. Traditionally, you would apply an output ACL to the interface connecting to the host to log packets that match the ACL. The logging information is dumped to the router console or system log. You then have to analyze this information, and possibly go through several ACLs in succession to identify the input interface for the attack. In this case the information points back to Router B.

You then repeat this process on Router B, which leads back to Router C, an ingress point into the network. At this point you can use ACLs or CAR to block the attack. This procedure can require applying several ACLs that generate an excessive amount of output to analyze, making this procedure cumbersome and error prone.

Figure 1

Source Tracking in a DoS Attack

IP source tracker provides an easier, more scalable alternative to output ACLs for tracking DoS attacks, and it works as follows:

• After you identify the destination being attacked, enable tracking for the destination address on the whole router by entering the ip source-track command.
• Each line card creates a special Cisco Express Forwarding (CEF) entry for the destination address being tracked. For line cards or port adapters that use specialized Application-Specific Integrated Circuit (ASICs) for packet switching, the CEF entry is used to punt packets to the line card's or port adapter's CPU.
• Each line card CPU collects information about the traffic flow to the tracked destination.
• The data generated is periodically exported to the router. To display a summary of the flow information, enter the show ip source-track summary command. To display more detailed information for each input interface, enter the show ip source-track command.
• Statistics provide a breakdown of the traffic to each tracked IP address. This breakdown allows you to determine which upstream router to analyze next. You can shut down the IP source tracker on the current router by entering the no ip source-track command, and reopen it on the upstream router.
• Repeat Step 1 to Step 5 until you identify the source of the attack.
• Apply CAR or ACLs to limit or stop the attack.

• IP Source Tracker Hardware Support
  

1.    enable

2.    configure terminal

3.    ip source-track ip-address

4.    ip source-track address-limit number

5.    ip source-track syslog-interval number

6.    ip source-track export-interval number

• What to Do Next
  

1.    enable

2.    show ip source-track [ip-address] [summary | cache

3.    show ip source-track export flows

Router# show ip source-track summary
Address          Bytes    Pkts    Bytes/s   Pkts/s
10.0.0.1          119G   1194M    443535      4432
192.168.1.1       119G   1194M    443535      4432
192.168.42.42     119G   1194M    443535      4432

Router# show ip source-track summary
Address        Bytes   Pkts   Bytes/s   Pkts/s
10.0.0.1           0      0         0        0 
192.168.1.1        0      0         0        0 
192.168.42.42      0      0         0        0 

Router# show ip source-track
Address         SrcIF    Bytes   Pkts   Bytes/s   Pkts/s
10.0.0.1        PO0/0    119G   1194M    513009     5127
192.168.1.1     PO0/0    119G   1194M    513009     5127