Perform this task to create a CLI view and add commands or interfaces to the view, as appropriate.

Perform this task to initialize and configure a view for lawful-intercept-specific commands and configuration information.

Perform this task to create a superview and add at least one CLI view to the superview.

The following example shows how to configure two CLI views, "first" and "second." Thereafter, you can verify the CLI view in the running configuration.

Router(config)# parser view first
00:11:40:%PARSER-6-VIEW_CREATED:view 'first' successfully created. 
Router(config-view)# secret 5 firstpass
Router(config-view)# command exec include show version
Router(config-view)# command exec include configure terminal
Router(config-view)# command exec include all show ip
Router(config-view)# exit
Router(config)# parser view second
00:13:42:%PARSER-6-VIEW_CREATED:view 'second' successfully created.
Router(config-view)# secret 5 secondpass
Router(config-view)# command exec include-exclusive show ip interface
Router(config-view)# command exec include logout
Router(config-view)# exit
!
!
Router(config-view)# do show run | beg view
parser view first
 secret 5 $1$MCmh$QuZaU8PIMPlff9sFCZvgW/
 commands exec include configure terminal
 commands exec include configure
 commands exec include all show ip
 commands exec include show version
 commands exec include show
!
parser view second
 secret 5 $1$iP2M$R16BXKecMEiQesxLyqygW.
 commands exec include-exclusive show ip interface
 commands exec include show ip
 commands exec include show
 commands exec include logout
!

After you have configured the CLI views "first" and "second," you can issue the enable viewcommand to verify which commands are available in each view. The following example shows which commands are available inside the CLI view "first" after the user has logged into this view. (Because the show ip command is configured with the all option, a complete set of suboptions is shown, except the show ip interface command, which is using the include-exclusive keyword in the second view.)

Router# enable view first
Password:
00:28:23:%PARSER-6-VIEW_SWITCH:successfully set to view 'first'.
Router# ?
Exec commands:
  configure  Enter configuration mode
  enable     Turn on privileged commands
  exit       Exit from the EXEC
  show       Show running system information
Router# show ?
  ip       IP information
  parser   Display parser information
  version  System hardware and software status
Router# show ip ?
 
  access-lists            List IP access lists
  accounting              The active IP accounting database
  aliases                 IP alias table
  arp                     IP ARP table
  as-path-access-list     List AS path access lists
  bgp                     BGP information
  cache                   IP fast-switching route cache
  casa                    display casa information
  cef                     Cisco Express Forwarding
  community-list          List community-list
  dfp                     DFP information
  dhcp                    Show items in the DHCP database
  drp                     Director response protocol
  dvmrp                   DVMRP information
  eigrp                   IP-EIGRP show commands
  extcommunity-list       List extended-community list
  flow                    NetFlow switching
  helper-address          helper-address table
  http                    HTTP information
  igmp                    IGMP information
  irdp                    ICMP Router Discovery Protocol
.
.
.

The following example shows how to configure a lawful intercept view, add users to the view, and verify the users that were added:

!Initialize the LI-View.
Router(config)# li-view lipass user li_admin password li_adminpass
00:19:25:%PARSER-6-LI_VIEW_INIT:LI-View initialized.
Router(config)# end
! Enter the LI-View; that is, check to see what commands are available within the view.
Router# enable view li-view
Password:
Router#
00:22:57:%PARSER-6-VIEW_SWITCH:successfully set to view 'li-view'.
Router# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)# parser view li-view
 
Router(config-view)# ?
View commands:
  commands  Configure commands for a view
  default   Set a command to its defaults
  exit      Exit from view configuration mode
  name      New LI-View name      ===This option only resides in LI View.
  no        Negate a command or set its defaults
  password  Set a password associated with CLI views
Router(config-view)#
! NOTE:LI View configurations are never shown as part of 'running-configuration'.
! Configure LI Users.
Router(config)# username lawful-intercept li-user1 password li-user1pass
 
Router(config)# username lawful-intercept li-user2 password li-user2pass
! Displaying LI User information.
Router# show users lawful-intercept
li_admin     
li-user1     
li-user2     
Router#

The following sample output from the show running-config command shows that "view_one" and "view_two" have been added to superview "su_view1," and "view_three" and "view_four" have been added to superview "su_view2":

!
parser view su_view1 superview
 secret 5 <encoded password>
 view view_one
 view view_two
!
parser view su_view2 superview
 secret 5 <encoded password>
 view view_three
 view view_four
!