The following sample
output is from the
show pce client peer
detail command.
Device# show pce client peer detail
PCC's peer database:
--------------------
Peer address: 10.1.1.1
State up
Capabilities: Stateful, Update, Segment-Routing
PCEP has been up for: 23:44:58
PCEP session ID: local 1, remote: 0
Sending KA every 30 seconds
Minimum acceptable KA interval: 20 seconds
Peer timeout after 120 seconds
Statistics:
Keepalive messages: rx 2798 tx 2112
Request messages: rx 0 tx 32
Reply messages: rx 32 tx 0
Error messages: rx 0 tx 0
Open messages: rx 1 tx 1
Report messages: rx 0 tx 57
Update messages: rx 72 tx 0
The following sample
output is from the
show mpls traffic-eng tunnels
tunnel 1 command which shows the LSP details.
Device# show mpls traffic-eng tunnels tunnel 1
Name: d1_t1 (Tunnel1) Destination: 10.7.7.7
Status:
Admin: up Oper: up Path: valid Signalling: connected
path option 10, (SEGMENT-ROUTING) (PCE) type dynamic (Basis for Setup, path weight 0)
Config Parameters:
Bandwidth: 200 kbps (Global) Priority: 5 5 Affinity: 0x0/0xFFFF
Metric Type: TE (default)
Path Selection:
Protection: any (default)
Path-selection Tiebreaker:
Global: not set Tunnel Specific: not set Effective: min-fill (default)
Hop Limit: disabled
Cost Limit: disabled
Path-invalidation timeout: 10000 msec (default), Action: Tear
AutoRoute: enabled LockDown: disabled Loadshare: 200 [10000000] bw-based
auto-bw: disabled
Fault-OAM: disabled, Wrap-Protection: disabled, Wrap-Capable: No
Active Path Option Parameters:
State: dynamic path option 10 is active
BandwidthOverride: disabled LockDown: disabled Verbatim: disabled
PCEP Info:
Delegation state: Working: yes Protect: no
Current Path Info:
Request status: processed
Created via PCRep message from PCE server: 10.1.1.1
Reported paths:
Tunnel Name: csr551_t2001
LSPs:
LSP[0]:
source 10.2.2.2, destination 10.7.7.7, tunnel ID 1, LSP ID 5
State: Admin up, Operation active
Setup type: SR
Bandwidth: signaled 0
LSP object:
PLSP-ID 0x807D1, flags: D:0 S:0 R:0 A:1 O:2
Reported path:
Metric type: TE, Accumulated Metric 0
History:
Tunnel:
Time since created: 34 minutes, 3 seconds
Time since path change: 1 minutes, 44 seconds
Number of LSP IDs (Tun_Instances) used: 5
Current LSP: [ID: 5]
Uptime: 1 minutes, 44 seconds
Prior LSP: [ID: 3]
ID: path option unknown
Removal Trigger: path verification failed
Tun_Instance: 5
Segment-Routing Path Info (isis level-1)
Segment0[Node]: 10.3.3.3, Label: 20270
Segment1[Node]: 10.6.6.6, Label: 20120
Segment2[Node]: 10.7.7.7, Label: 20210
The following sample
output is from the
show pce client lsp
detail command.
Device# show pce client lsp detail
PCC's tunnel database:
----------------------
Tunnel Name: d1_t1
LSPs:
LSP[0]:
source 10.2.2.2, destination 10.7.7.7, tunnel ID 1, LSP ID 5
State: Admin up, Operation active
Setup type: SR
Bandwidth: signaled 0
LSP object:
PLSP-ID 0x807D1, flags: D:0 S:0 R:0 A:1 O:2
Reported path:
Metric type: TE, Accumulated Metric 0
The
following sample output is from the
show pce lsp
detail command which shows the tunnel is delegated.
Device# show pce lsp detail
Thu Jul 7 10:24:30.836 EDT
PCE's tunnel database:
----------------------
PCC 10.103.2.1:
Tunnel Name: d1_t1
LSPs:
LSP[0]:
source 10.2.2.2, destination 10.7.7.7, tunnel ID 1, LSP ID 5
State: Admin up, Operation active
Binding SID: 0
PCEP information:
plsp-id 526289, flags: D:1 S:0 R:0 A:1 O:2
Reported path:
Metric type: TE, Accumulated Metric 0
SID[0]: Node, Label 20270, Address 10.3.3.3
SID[1]: Node, Label 20120, Address 10.6.6.6
SID[2]: Node, Label 20210, Address 10.7.7.7
Computed path:
Metric type: TE, Accumulated Metric 30
SID[0]: Node, Label 20270, Address 10.3.3.3
SID[1]: Node, Label 20120, Address 10.6.6.6
SID[2]: Node, Label 20210, Address 10.7.7.7
Recorded path:
None
The following sample
output is from the
show pce client lsp
detail command for reported tunnel.
Device# show pce client lsp detail
PCC's tunnel database:
----------------------
Tunnel Name: d1_t2
LSPs:
LSP[0]:
source 10.2.2.2, destination 10.7.7.7, tunnel ID 2, LSP ID 1
State: Admin up, Operation active
Setup type: SR
Bandwidth: signaled 0
LSP object:
PLSP-ID 0x807D2, flags: D:0 S:0 R:0 A:1 O:2
Reported path:
Metric type: TE, Accumulated Metric 30
The following sample
output is from the
show pce lsp
detail command which shows the tunnel is not delegated.
Device# show pce lsp detail
Thu Jul 7 10:29:48.754 EDT
PCE's tunnel database:
----------------------
PCC 10.0.0.1:
Tunnel Name: d1_t2
LSPs:
LSP[0]:
source 10.2.2.2, destination 10.7.7.7, tunnel ID 2, LSP ID 1
State: Admin up, Operation active
Binding SID: 0
PCEP information:
plsp-id 526290, flags: D:0 S:0 R:0 A:1 O:2
Reported path:
Metric type: TE, Accumulated Metric 30
SID[0]: Adj, Label 74, Address: local 172.16.0.1 remote 172.16.0.2
SID[1]: Adj, Label 63, Address: local 172.17.0.1 remote 172.17.0.2
SID[2]: Adj, Label 67, Address: local 172.18.0.1 remote 172.18.0.2
SID[3]: Node, Label unknownAddress 10.7.7.7
Computed path:
None
Recorded path:
None
Feedback