- Wide-Area Networking Overview
- Configuring Frame Relay
- Adaptive Frame Relay Traffic Shaping for Interface Congestion
- Frame Relay 64-Bit Counters
- Frame Relay MIB Enhancements
- Frame Relay Point-Multipoint Wireless
- Frame Relay Queueing and Fragmentation at the Interface
- Frame Relay PVC Bundles with QoS Support for IP and MPLS
- Frame Relay Voice-Adaptive Traffic Shaping and Fragmentation
- Frame Relay IP RTP Priority
- PPP over Frame Relay
- MQC-Based Frame Relay Traffic Shaping
- Frame Relay PVC Interface Priority Queueing
- Multilink Frame Relay FRF.16.1
- Distributed Multilink Frame Relay FRF.16
- Configuring Frame Relay-ATM Interworking
- Frame Relay-ATM Interworking Supported Standards
Contents
- PPP over Frame Relay
- Finding Feature Information
- Prerequisites for PPP over Frame Relay
- Restrictions for PPP over Frame Relay
- Information About PPP over Frame Relay
- Overview of PPP over Frame Relay
- Benefits
- How to Configure PPP over Frame Relay
- Enabling PPP over Frame Relay
- Configuration Examples for PPP over Frame Relay
- Example PPP over Frame Relay DTE
- Example PPP over Frame Relay DCE
- Additional References
- Feature Information for PPP over Frame Relay
- Glossary
PPP over Frame Relay
The PPP over Frame Relay feature allows a router to establish end-to-end Point-to-Point Protocol (PPP) sessions over Frame Relay.
- Finding Feature Information
- Prerequisites for PPP over Frame Relay
- Restrictions for PPP over Frame Relay
- Information About PPP over Frame Relay
- How to Configure PPP over Frame Relay
- Configuration Examples for PPP over Frame Relay
- Additional References
- Feature Information for PPP over Frame Relay
- Glossary
Finding Feature Information
Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
Prerequisites for PPP over Frame Relay
Before you can configure PPP over Frame Relay, Frame Relay must be enabled on the router using the encapsulation frame-relay command.
Restrictions for PPP over Frame Relay
Only Frame Relay permanent virtual circuits (PVCs) are supported.
Only the Internet Protocol (IP) is supported.
Information About PPP over Frame Relay
Overview of PPP over Frame Relay
The PPP over Frame Relay feature allows a router to establish end-to-end Point-to-Point Protocol (PPP) sessions over Frame Relay. IP datagrams are transported over the PPP link using RFC 1973 compliant Frame Relay framing. This feature is useful for remote users running PPP to access their Frame Relay corporate networks as shown in the figure below.
The figure below shows a connectivity scenario using the Cisco 90i D4 channel card, which is capable of supporting Integrated Services Digital Network (ISDN) Digital Service Loop (DSL), PPP, or Frame Relay, which connects to an Internet Service Provider (ISP) or corporate network.
PPP over Frame Relay is compliant with the functionality and encapsulation specifications as outlined in RFC 1973. The frame format is shown in the figure below.
A PPP connection is established over the Frame Relay PVC. The PPP session does not occur unless the associated Frame Relay PVC is in an "active" state. The Frame Relay VC can coexist with other circuits using different Frame Relay encapsulation methods, such as RFC 1490 and Cisco proprietary, over the same Frame Relay link. There can be multiple PPP-in-Frame-Relay circuits existing on one Frame Relay link.
One PPP connection resides on one virtual access interface, which is internally created from a virtual template interface. A virtual access interface is cloned from a virtual template interface. The virtual access interfaces is coexistent with the creation of the Frame Relay circuit when the corresponding DLCI is configured. One virtual template interface, containing all the necessary PPP and network protocol information, is shared by multiple virtual access interfaces. Hardware compression and fancy queuing algorithms, such as weighted fair queuing, custom queuing, and priority queuing, are not applied to virtual access interfaces. Once a Frame Relay circuit is established using PPP over Frame Relay, all incoming and outgoing packets on this circuit are under RFC 1973 PPP-in-Frame-Relay encapsulation compliance until this DLCI is removed from the configuration.
The breakdown of the Frame Relay frame format components is listed in the table below.
|
Field |
Description |
|---|---|
|
Flag |
A single byte that indicates the beginning or end of a frame. |
|
Address |
A two-byte field that indicates the logical connection that maps to the physical channel; the DLCI. |
|
Control |
A single byte that calls for transmission of user data. PPP over Frame Relay uses a value of 0X03, which indicates that the frame is an unnumbered information (UI) frame. |
|
NLPID |
Network layer protocol ID, which is a single byte that uniquely identifies a PPP packet to Frame Relay. |
|
PPP protocol |
Identifies the PPP packet type. |
Benefits
Allows end-to-end PPP sessions over Frame Relay.
Supports the 90i IDSL Channel Unit that supports both Frame Relay and PPP on an ISDN DSL.
How to Configure PPP over Frame Relay
Enabling PPP over Frame Relay
Perform the following task to configure the physical interface that carries the PPP session and links to the appropriate virtual template interface.
After you configure the Cisco router or access server for Frame Relay encapsulation, you must configure the physical interface with the PVC and apply a virtual template with PPP encapsulation to the DLCI that it applies to.
1.
enable
2.
configure
terminal
3.
interface
type
number
.
subinterface-number
{multipoint | point-to-point}
4.
frame-relay
interface-dlci
dlci
[ppp virtual-template-name-string]
5.
end
DETAILED STEPS
Configuration Examples for PPP over Frame Relay
Example PPP over Frame Relay DTE
The following example configures a router as a data terminating equipment (DTE) device for PPP over Frame Relay. Subinterface 2.1 contains the necessary DLCI and virtual template information. The virtual template interface (interface virtual-template 1) contains the PPP information that is applied to the PPP session associated with DLCI 32 on serial subinterface 2.1.
interface serial 2 no ip address encapsulation frame-relay frame-relay lmi-type ansi ! interface serial 2.1 point-to-point frame-relay interface-dlci 32 ppp virtual-template1 ! interface Virtual-Template1 ip unnumbered ethernet 0 ppp authentication chap pap
 Note | By default, the encapsulation type for a virtual template interface is PPP encapsulation; therefore, the encapsulation ppp command will not show up when viewing the running configuration on the router. |
Example PPP over Frame Relay DCE
The following example configures a router to act as a data communications equipment (DCE) device. Typically, a router is configured as a DCE if connecting directly to another router or if connected to a 90i D4 channel unit, which is connected to a telco channel bank. The three commands required for this type of configuration are frame-relay switching, frame-relay intf-type dce, and frame-relay route commands.
frame-relay switching ! interface Serial2/0:0 no ip address encapsulation frame-relay IETF frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 31 interface Serial1/2 100 frame-relay interface-dlci 32 ppp Virtual-Template1 ! interface Serial2/0:0.2 point-to-point no ip address frame-relay interface-dlci 40 ppp Virtual-Template2 ! interface Virtual-Template1 ip unnumbered Ethernet0/0 peer default ip address pool default ppp authentication chap pap ! interface Virtual-Template2 ip address 209.165.200.225 255.255.255.224 ppp authentication chap pap
Note | By default, the encapsulation type for a virtual template interface is PPP encapsulation; therefore, the encapsulation ppp command will not show up when viewing the running configuration on the router. |
Additional References
Related Documents
|
Related Topic |
Document Title |
|---|---|
|
Cisco IOS commands |
|
|
WAN commands |
Cisco IOS Wide-Area Networking Command Reference |
|
Configuring Frame Relay |
Configuring Frame Relay |
Standards
|
Standard |
Title |
|---|---|
|
None |
-- |
MIBs
|
MIB |
MIBs Link |
|---|---|
|
None |
To locate and download MIBs for selected platforms, Cisco software releases, and feature sets, use Cisco MIB Locator found at the following URL: |
RFCs
|
RFC |
Title |
|---|---|
|
RFC 1973 |
PPP in Frame Relay |
Technical Assistance
|
Description |
Link |
|---|---|
|
The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password. |
Feature Information for PPP over Frame Relay
The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
|
Feature Name |
Releases |
Feature Information |
|---|---|---|
|
PPP over Frame Relay |
11.3(4)T 15.0(1)S |
The PPP over Frame Relay feature allows a router to establish end-to-end PPP sessions over Frame Relay. The following commands were introduced or modified: debug frame-relay ppp, frame-relay interface-dlci, show frame-relay pvc. |
Glossary
data-link connection identifier (DLCI) --A value that specifies a PVC or SVC in a Frame Relay network. In the basic Frame Relay specification, DLCIs are locally significant (connected devices might use different values to specify the same connection). In the LMI extended specification, DLCIs are globally significant (DLCIs specify individual end devices).
Integrated Services Digital Network (ISDN) --Communication protocols offered by telephone companies that permit telephone networks to carry data, voice, and other source traffic.
Link Control Protocol (LCP) --A protocol that establishes, configures, and tests data link connections used by PPP.
permanent virtual circuit (PVC) --Virtual circuit that is permanently established. PVCs save bandwidth associated with circuit establishment and teardown in situations where certain virtual circuits must exist all the time.
Point-to-Point Protocol (PPP) --A protocol that encapsulates network layer protocol information over point-to-point links. The RFC for PPP is RFC 1661.
virtual circuit (VC) -- A logical circuit created to ensure reliable communication between two network devices. A virtual circuit can be either permanent (a PVC) or switched (an SVC). Virtual circuits are used in Frame Relay and X.25.