March 2007

Revision History Table added for the first time

June 2007

Added a new procedure, NTP-G192, to the "Provision Transponder and Muxponder Cards" chapter for force FPGA image upgrade.

August 2007

Updated About this Guide chapter.

September 2007

Updated the NTP-G130 Remove a DWDM Node procedure in the "Add and Removed Cards and Nodes" chapter.

November 2007

Added a new procedure, NTP-G196, to the "Provision Transponder and Muxponder Cards" for force FPGA update when the Card is part of a Protection Group.

March 2008

Updated the procedure to delete a Y-Cable Protection Group and added a note in the "DLP-G177 Delete a Y-Cable Protection Group" section in Chapter 10, "Manage the Node".

July 2008

Updated the fuse ratings in the following sections in Chapter 1, Install the Shelf and Common Control Cards:

•DLP-G5 Mount the Shelf Assembly in a Rack (One Person)

•NTP-G7 Install the Power and Ground

•DLP-G19 Turn On and Verify Office Power

•DLP-G6 Mount the Shelf Assembly in a Rack (Two People)

•DLP-G7 Mount Multiple Shelf Assemblies in a Rack

December 2008

Added a note in the "Change the 10G Data Muxponder Port Mode" section of Chapter 5 Provision Transponder and Muxponder Cards.

May 2009

Updated "CTC Menu and Toolbar Options" section in Appendix A, CTC Information and Shortcuts.

October 2009

Updated the "Clean Fiber Optic Connectors" procedure in Chapter 13, "Maintain the Node".

Added the "Clean Multi Fiber-Optic Cable Connectors" procedure in Chapter 13, "Maintain the Node".

November 2009

Added a note in "Delete a PPM" procedure in the chapter, "Provision Transponder and Muxponder Cards".

June 2010

Updated the table with EAP cable length in NTP-G145 in the chapter, Install the Shelf and Common Control Cards.

July 2010

Deleted the section "DLP-G313 Verify OSC-CSM Transmit Power" in the chapter "Turn Up a Node".

November 2010

Updated step 21 in "NTP-G42 Perform the Terminal Node with 32WSS and 32DMX Cards Acceptance Test"

Updated step 22 in "NTP-G153 Perform the Terminal Node with 32WSS-L and 32DMX-L Cards Acceptance Test"

June 2011

Updated step 5 in the procedure "Remove Permanently or Remove and Replace DWDM Cards" of the chapter, "Upgrade, Add, and Remove Cards and Nodes".

December 2011

•Updated the procedure "DLP-G76 Provision DCC/GCC Terminations" in the chapter "Create Channels and Circuits".

•Updated the following procedures in the chapter "Manage the Node":

–NTP-G85 Modify or Delete OSC Terminations, DCC/GCC Terminations, and Provisionable Patchcords

–DLP-G184 Change a DCC/GCC Termination

–DLP-G185 Delete a DCC/GCC Termination

February 2012

Updated the procedure "DLP-G278 Provision the Optical Line Rate" in the chapter "Provision Transponder and Muxponder Cards".

March 2012

Added a note in the procedure "NTP-G354 Create an Internal Patchcord Manually" in the chapter "Turn Up a Node".

April 2012

Added a note in the procedure "DLP-G368 Change the 10G Multirate Transponder Trunk Wavelength Settings" in the chapter "Provision Transponder and Muxponder Cards".

May 2012

Updated the "Set Up SNMP" procedure in the chapter "Turn Up a Node".

June 2012

Document Part Number revisioned to 78-17737-03 and a full length book-PDF was generated.

July 2012

Updated the task "NTP-G130 Remove a DWDM Node" in the chapter "Add and Remove Nodes".

September 2012

•Updated the procedures "NTP-G60 Create and Delete Overhead Circuits" and "DLP-G76 Provision DCC/GCC Terminations" in the chapter "Create Channels and Circuits".

•Updated the procedure "NTP-G38 Provision OSC Terminations" in the chapter "Turn Up a Node".

boldface

Commands and keywords in body text.

italic

Command input that is supplied by the user.

[     ]

Keywords or arguments that appear within square brackets are optional.

{ x | x | x }

A choice of keywords (represented by x) appears in braces separated by vertical bars. The user must select one.

Ctrl

The control key. For example, where Ctrl + D is written, hold down the Control key while pressing the D key.

screen font

Examples of information displayed on the screen.

boldface screen font

Examples of information that the user must enter.

<     >

Command parameters that must be replaced by module-specific codes.

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071

SAVE THESE INSTRUCTIONS

Waarschuwing

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.

BEWAAR DEZE INSTRUCTIES

Varoitus

TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

Attention

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

Warnung

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

Avvertenza

IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

Advarsel

VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

Aviso

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.

GUARDE ESTAS INSTRUÇÕES

¡Advertencia!

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

Varning!

VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.

SPARA DESSA ANVISNINGAR

Aviso

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUÇÕES

Advarsel

VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER