About this Guide
Note 
The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.
This section explains the objectives, intended audience, and organization of this publication and describes the conventions that convey instructions and other information.
This section provides the following information:
•Revision History
•Document Objectives
•Audience
•Important Notes about TL1 Commands
•Related Documentation
•Document Conventions
•Obtaining Optical Networking Information
•Obtaining Documentation and Submitting a Service Request
Revision History
|
|
|
March 2007 |
Added the Revision History table. |
April 2007 |
Added description for service state transitions in ED-<OCN_TYPE>, ED-EC1, ED-T1, and ED-T3 commands in the "ED Commands" chapter. |
May 2007 |
Added a note regarding Telecordia GR831 non-compliant data and TL1 response in the "RTRV Commands" chapter. |
July 2007 |
Updated About this Guide chapter. |
December 2007 |
Added <SUPPRESS> parameter for ED-ETH, ED-POS, and ED-GIGE commands. |
April 2008 |
•Changed the minute range for REPTINVL from 1-1440 min to 5-1440 min for SCHED-PMREPT command in the SCHED Commands chapter. •Updated aidtype, cardmode, and equipment type in ED-EQPT, ENT-EQPT, and RTRV-EQPT commands in Chapter 11, ED Commands, Chapter 12, ENT Commands, and Chapter 21, RTRV Commands. •Updated parameters in ED-GFP and ED-NE-GEN commands in Chapter 11, ED Commands. •Updated parameters in RTRV-NE-GEN in Chapter 21, RTRV Commands. |
May 2008 |
Added a note to the COPY-RFILE command. |
June 2008 |
•Deleted the <PH> parameter and updated the Input Format, Example, and Parameter for the INIT-SYS command in section 15.2 of Chapter 15, INIT Commands. •Added a note to the RTRV-FAC command. |
September 2008 |
Added the table "CTC Port Numbers and TL1 Aids" in the chapter, Access Identifiers. |
November 2008 |
Updated Fan Tray AID description in EQPT AIDs table in Chapter 25, Access Identifiers. |
May 2009 |
•Updated input parameter description for ED-<OCN_TYPE> command in Chapter 11, ED Commands. •Added Facility AID format for CE-100T-8 and MS-ISC-100T cards in Chapter 25, Access Identifiers. •Added prerequisites to COPY-RFILE command. •Updated the input parameters for the ENT-OCHNC command in the chapter, ENT Commands. •Updated the following: –The input format, input example and input parameters for the OPR-APC command in the chapter, OPR Commands. –The WDMANS AID in the chapter, Access Identifiers. •Updated the supported platform for SW-DX-EQPT in Chapter 24, SW Commands. |
June 2009 |
•Updated the input parameters for the APPLY command in Chapter 3, APPLY Commands. •Updated the output parameter for the RTRV-FAC command in Chapter 21, RTRV Commands. •Updated the following: –The output example and output parameters for the RTRV-CMD-SECU command in Chapter 21, RTRV Commands. –The input example and input parameters for the ED-CMD-SECU command in Chapter 11, ED Commands. |
August 2009 |
Updated the input parameter description for APPLY command in Chapter 3, APPLY Commands. |
September 2009 |
Updated the PH parameter description in Chapter 15, INIT Commands. |
November 2009 |
•Updated "OPR-PROTNSW-OCH" command description in Chapter 16, OPR Commands. •Updated the <PJMON> parameter description in Chapter 11, ED Commands. •Updated the <PJMON> parameter description in Chapter 21, RTRV Commands. |
January 2010 |
Updated the input format, input example, and added a new parameter <OPRNOMINAL> for ED-<OCN_TYPE> command in Chapter 11, ED Commands. |
February 2010 |
Updated Input Parameters table in Chapter "INIT Commands". |
July 2010 |
•Updated the "RTRV-AUDIT-LOG" command in the chapter "RTRV Commands". •Updated the input parameter for the INIT-SYS command in the chapter, INIT Commands. |
September 2010 |
Updated the table RFILE in the chapter "Access Identifiers". |
November 2010 |
Removed the "prerequisite" section from the "COPY-RFILE" command. |
April 2011 |
Updated the input parameter description for the ED-<OCN_TYPE> command in the chapter, ED Commands. |
May 2011 |
Updated the output parameter description for the RTRV-<OCN_TYPE> command in the chapter, RTRV Commands. |
July 2011 |
Updated the description for RFILE-DB in "RFILE" section in the chapter, "Access Identifiers" |
March 2012 |
Added Facility AID for CE1000 cards in the chapter "Access Identifiers". |
August 2012 |
The full length book-PDF was generated. |
October 2012 |
Updated the input example for the ED-<MOD1FCPAYLOAD> command in the chapter, ED Commands. |
December 2012 |
Updated the ENT-RMONTH-<MOD2> command in the chapter, "ENT Commands" and RTRV-RMONTH-<MOD2> command in the chapter "RTRV Commands". |
February 2013 |
•Updated the section, "ENT-LNKTERM" in the chapter "ENT Commands". •Added a new section "Important Notes about TL1 Commands" in the "Preface" chapter. •Added "BIT-EC" counter in the output parameters table for "MONTYPE" parameter in the chapters "INIT Commands", "RTRV Commands", and "SET Commands". |
Document Objectives
This guide explains the use of Transaction Language 1 (TL1) for the Cisco ONS 15454, ONS 15310-CL, ONS 15310-MA, and ONS 15600 systems. Use this guide in conjunction with the appropriate publications listed in the Related Documentation section.
Audience
To use this publication, you should be familiar with Cisco or equivalent optical transmission hardware and cabling, telecommunications hardware and cabling, electronic circuitry and wiring practices, and preferably have experience as a telecommunications technician.
Important Notes about TL1 Commands
TL1 commands can be executed manually or through the use of scripts.
When commands are executed manually, there is a delay of few seconds before the next command can be executed. This gives the Network Elements (NE) sufficient time to perform most of the database (DB) operations.
However, when commands are executed using scripts, the functioning of the NE differs. The NE has insufficient time to perform all the database operations and may cause the NE to malfunction. This in turn causes the controller card to reboot. To prevent this, it is recommended that a delay of 3 to 5 seconds be added between the commands that require DB updates in the script.
Related Documentation
Use the Cisco ONS SONET TL1 Command Guide, R8.0 in conjunction with the following referenced publications:
•Cisco ONS SONET TL1 Reference Guide, Release 8.0
Provides general information, procedures, and errors related to using TL1 in the Cisco ONS 15454, ONS 15310-CL, ONS 15310-MA, and ONS 15600.
•Cisco ONS SONET TL1 Command Quick Reference Guide, Release 8.0
Provides input formats and output formats (where applicable) for all R8.0 TL1 commands and autonomous messages.
•Cisco ONS SONET TL1 for Beginners, Release 8.0
Provides basic beginning instruction for using TL1.
•Cisco ONS 15454 Procedure Guide, Release 8.0
Cisco ONS 15310-CL and Cisco ONS 15310-MA Procedure Guide, Release 8.0
Cisco ONS 15600 Procedure Guide, Release 8.0
Provides procedures and tasks for the corresponding Cisco ONS node and network.
•Cisco ONS 15454 Reference Manual, Release 8.0
Cisco ONS 15310-CL and Cisco ONS 15310-MA Reference Manual, Release 8.0
Cisco ONS 15600 Reference Manual, Release 8.0
Provides reference material for the corresponding Cisco ONS node and network.
•Cisco ONS 15454 Troubleshooting Guide, Release 8.0
Cisco ONS 15310-CL and Cisco ONS 15310-MA Troubleshooting Guide, Release 8.0
Cisco ONS 15600 Troubleshooting Guide, Release 8.0
Provides general troubleshooting procedures, alarm descriptions, performance monitoring parameters, and Simple Network Management Protocol (SNMP) parameters for the corresponding Cisco ONS node and network.
•Cisco ONS 15454 DWDM Procedure Guide, Release 8.0
Explains installation, turn up, provisioning, and maintenance for Cisco ONS 15454 dense wavelength division (DWDM) systems.
•Cisco ONS 15454 DWDM Reference Manual, Release 8.0
Explains installation, turn up, provisioning, and maintenance for Cisco ONS 15454 dense wavelength division (DWDM) systems.
•Cisco ONS 15454 DWDM Troubleshooting Guide, Release 8.0
Provides troubleshooting information and troubleshooting-related parameters for the Cisco ONS 15454 (ANSI) and Cisco ONS 15454 SDH (ETSI) platforms, specifically the dense wavelength division multiplexing (DWDM) application that can operate on either platform.
•Cisco ONS 15454 and Cisco ONS 15454 SDH Ethernet Card Software Feature and Configuration Guide, Release 8.0
Provides software features for all Ethernet cards and configuration information for Cisco IOS on ML-Series cards.
•Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide, Release 8.0
Provides software features and operations of the ML-100T-8 and the CE-100T-8 Ethernet cards for the Cisco ONS 15310-CL and the Cisco ONS 15310-MA.
•Release Notes for the Cisco ONS 15454 Release 8.0
Release Notes for the Cisco ONS 15310-CL Release 8.0
Release Notes for the Cisco ONS 15310-MA Release 8.0
Release Notes for the Cisco ONS 15600 Release 8.0
Provides caveats, closed issues, and new feature and functionality information.
For an update on End-of-Life and End-of-Sale notices, refer to http://cisco.com/en/US/products/hw/optical/ps2001/prod_eol_notices_list.html
Document Conventions
This publication uses the following conventions:
|
|
|
[ ] |
Keywords or arguments that appear within square brackets are optional. |
{ x | x | x } |
A choice of keywords (represented by x) appears in braces separated by vertical bars. The user must select one. |
Ctrl |
The control key. For example, where Ctrl + D is written, hold down the Control key while pressing the D key. |
screen font |
Examples of information displayed on the screen. |
< > |
Command parameters that must be replaced by module-specific codes. |
Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the document.
Caution
Means
reader be careful. In this situation, the user might do something that could result in equipment damage or loss of data.
 |
Warning
|
|
IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071 SAVE THESE INSTRUCTIONS |
Waarschuwing |
BELANGRIJKE VEILIGHEIDSINSTRUCTIES Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen. BEWAAR DEZE INSTRUCTIES |
Varoitus |
TÄRKEITÄ TURVALLISUUSOHJEITA Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla. SÄILYTÄ NÄMÄ OHJEET |
Attention |
IMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement. CONSERVEZ CES INFORMATIONS |
Warnung |
WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden. BEWAHREN SIE DIESE HINWEISE GUT AUF. |
Avvertenza |
IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento. CONSERVARE QUESTE ISTRUZIONI |
Advarsel |
VIKTIGE SIKKERHETSINSTRUKSJONER Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten. TA VARE PÅ DISSE INSTRUKSJONENE |
Aviso |
INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo. GUARDE ESTAS INSTRUÇÕES |
¡Advertencia! |
INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. GUARDE ESTAS INSTRUCCIONES |
Varning! |
VIKTIGA SÄKERHETSANVISNINGAR Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR |
|
|
|
|
|
|
|
|
|
|
Aviso |
INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo. GUARDE ESTAS INSTRUÇÕES |
Advarsel |
VIGTIGE SIKKERHEDSANVISNINGER Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed. GEM DISSE ANVISNINGER |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Obtaining Optical Networking Information
This section contains information that is specific to optical networking products. For information that pertains to all of Cisco, refer to the Obtaining Documentation and Submitting a Service Request section.
Where to Find Safety and Warning Information
For safety and warning information, refer to the Cisco Optical Transport Products Safety and Compliance Information document that accompanied the product. This publication describes the international agency compliance and safety information for the Cisco ONS 15454 system. It also includes translations of the safety warnings that appear in the ONS 15454 system documentation.
Cisco Optical Networking Product Documentation CD-ROM
Optical networking-related documentation, including Cisco ONS 15xxx product documentation, is available in a CD-ROM package that ships with your product. The Optical Networking Product Documentation CD-ROM is updated periodically and may be more current than printed documentation.
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.
Feedback