- Preface
- Cisco ONS Documentation Roadmap for Release 9.2.1
- Chapter 1, CE-Series Ethernet Cards
- Chapter 2, E-Series and G-Series Ethernet Cards
-
- Chapter 3, ML-Series Cards Overview
- Chapter 4, CTC Operations
- Chapter 5, Initial Configuration
- Chapter 6, Configuring Interfaces
- Chapter 7, Configuring CDP
- Chapter 8, Configuring POS
- Chapter 9, Configuring Bridges
- Chapter 10, Configuring IEEE 802.1Q Tunneling and Layer 2 Protocol Tunneling
- Chapter 11, Configuring STP and RSTP
- Chapter 12, Configuring Link Aggregation
- Chapter 13, Configuring Security for the ML-Series Card
- Chapter 14, Configuring RMON
- Chapter 15, Configuring SNMP
- Chapter 16, Configuring VLAN
- Chapter 17, Configuring Networking Protocols
- Chapter 18, Configuring IRB
- Chapter 19, Configuring IEEE 802.17b Resilient Packet Ring
- Chapter 20, Configuring VRF Lite
- Chapter 21, Configuring Quality of Service
- Chapter 22, Configuring Ethernet over MPLS
- Chapter 23, Configuring the Switching Database Manager
- Chapter 24, Configuring Access Control Lists
- Chapter 25, Configuring Cisco Proprietary Resilient Packet Ring
-
- Chapter 26, ML-MR-10 Card Overview
- Chapter 27, IP Host Functionality on the ML-MR-10 Card
- Chapter 29: Configuring Security for the ML-MR-10 Card
- Chapter 30: Configuring IEEE 802.17b Resilient Packet Ring on the ML-MR-10 Card
- Chapter 31, Configuring POS on the ML-MR-10 Card
- Chapter 32, Configuring Card Port Protection on the ML-MR-10 Card
- Chapter 32, Configuring Ethernet Virtual Circuits and QoS on the ML-MR-10 Card
- Chapter 34: Configuring Link Agrregation on ML-MR-10 card
- Chapter 35, Configuring Ethernet OAM (IEEE 802.3ah), CFM (IEEE 802.1ag), and E-LMI on the ML-MR-10 Card
- Appendix A: CPU and Memory Utilization on the ML-MR-10 Card
- Appendix A, POS on ONS Ethernet Cards
- Appendix B, Command Reference
- Appendix C, Unsupported CLI Commands
- Appendix D, Using Technical Support
Configuring IRB
Note 
This chapter applies only to the ML-Series (ML100T-2, ML100X-8, and ML1000-2) cards.
This chapter describes how to configure integrated routing and bridging (IRB) for the ML-Series card. For more information about the Cisco IOS commands used in this chapter, refer to the Cisco IOS Command Reference publication.
This chapter includes the following major sections:
•Understanding Integrated Routing and Bridging
Cisco Inter-Switch Link (ISL) and Cisco Dynamic Trunking Protocol (DTP) are not supported by the ML-Series, but the ML-Series broadcast forwards these formats. Using ISL or DTP on connecting devices is not recommended. Some Cisco devices attempt to use ISL or DTP by default.
Understanding Integrated Routing and Bridging
Your network might require you to bridge local traffic within several segments and have hosts on the bridged segments reach the hosts or ML-Series card on routed networks. For example, if you are migrating bridged topologies into routed topologies, you might want to start by connecting some of the bridged segments to the routed networks.
Using the integrated routing and bridging (IRB) feature, you can route a given protocol between routed interfaces and bridge groups within a single ML-Series card. Specifically, local or unroutable traffic is bridged among the bridged interfaces in the same bridge group, while routable traffic is routed to other routed interfaces or bridge groups.
Because bridging is in the data link layer and routing is in the network layer, they have different protocol configuration models. With IP, for example, bridge group interfaces belong to the same network and have a collective IP network address. In contrast, each routed interface represents a distinct network and has its own IP network address. Integrated routing and bridging uses the concept of a Bridge Group Virtual Interface (BVI) to enable these interfaces to exchange packets for a given protocol.
A BVI is a virtual interface within the ML-Series card that acts like a normal routed interface. A BVI does not support bridging but actually represents the corresponding bridge group to routed interfaces within the ML-Series card. The interface number is the link between the BVI and the bridge group.
Before configuring IRB, consider the following:
•The default routing/bridging behavior in a bridge group (when IRB is enabled) is to bridge all packets. Make sure that you explicitly configure routing on the BVI for IP traffic.
•Packets of unroutable protocols such as local-area transport (LAT) are always bridged. You cannot disable bridging for the unroutable traffic.
•Protocol attributes should not be configured on the bridged interfaces when you are using IRB to bridge and route a given protocol. You can configure protocol attributes on the BVI, but you cannot configure bridging attributes on the BVI.
•A bridge links several network segments into one large, flat network. To bridge a packet coming from a routed interface among bridged interfaces, the bridge group should be represented by one interface.
•All ports in a BVI group must have matching maximum transmission unit (MUTT) settings.
Configuring IRB
The process of configuring integrated routing and bridging consists of the following tasks:
1. Configure bridge groups and routed interfaces.
a. Enable bridging.
b. Assign interfaces to the bridge groups.
c. Configure the routing.
2. Enable IRB.
3. Configure the BVI.
a. Enable the BVI to accept routed packets.
b. Enable routing on the BVI.
4. Configure IP addresses on the routed interfaces.
5. Verify the IRB configuration.
When you configure the BVI and enable routing on it, packets that come in on a routed interface destined for a host on a segment that is in a bridge group are routed to the BVI and forwarded to the bridging engine. From the bridging engine, the packet exits through a bridged interface. Similarly, packets that come in on a bridged interface but are destined for a host on a routed interface go first to the BVI. The BVI forwards the packets to the routing engine that sends them out on the routed interface.
To configure a bridge group and an interface in the bridge group, perform the following procedure, beginning in global configuration mode:
To enable and configure IRB and BVI, perform the following procedure, beginning in global configuration mode:
IRB Configuration Example
Figure 18-1 shows an example of IRB configuration. Example 18-1 shows the configuration code for Router A, and Example 18-2 shows the configuration code for Router B.
Figure 18-1 Configuring IRB
Example 18-1 Configuring Router A
bridge irb
bridge 1 protocol ieee
bridge 1 route ip
!
!
interface FastEthernet0
ip address 192.168.2.1 255.255.255.0
!
interface POS0
no ip address
crc 32
bridge-group 1
pos flag c2 1
!
interface POS1
no ip address
crc 32
bridge-group 1
pos flag c2 1
!
interface BVI1
ip address 192.168.1.1 255.255.255.0
!
router ospf 1
log-adjacency-changes
network 192.168.1.0 0.0.0.255 area 0
network 192.168.2.0 0.0.0.255 area 0
Example 18-2 Configuring Router B
bridge irb
bridge 1 protocol ieee
bridge 1 route ip
!
!
interface FastEthernet0
ip address 192.168.3.1 255.255.255.0
!
interface POS0
no ip address
crc 32
bridge-group 1
pos flag c2 1
!
interface POS1
no ip address
crc 32
bridge-group 1
pos flag c2 1
!
interface BVI1
ip address 192.168.1.2 255.255.255.0
!
router ospf 1
log-adjacency-changes
network 192.168.1.0 0.0.0.255 area 0
network 192.168.3.0 0.0.0.255 area 0
Monitoring and Verifying IRB
Table 18-1 shows the privileged EXEC commands for monitoring and verifying IRB.
Example 18-3 is sample output from the show interfaces bvi and show interfaces irb commands.
Example 18-3 Monitoring and Verifying IRB
Router# show interfaces bvi1
BVI1 is up, line protocol is up
Hardware is BVI, address is 0011.2130.b340 (bia 0000.0000.0000)
Internet address is 100.100.100.1/24
MTU 1500 bytes, BW 145152 Kbit, DLY 5000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input 03:35:28, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/0 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
1353 packets output, 127539 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
Router# show interfaces irb
BVI1
Software MAC address filter on BVI1
Hash Len Address Matches Act Type
0x00: 0 ffff.ffff.ffff 0 RCV Physical broadcast
GigabitEthernet0
Bridged protocols on GigabitEthernet0:
clns ip
Software MAC address filter on GigabitEthernet0
Hash Len Address Matches Act Type
0x00: 0 ffff.ffff.ffff 0 RCV Physical broadcast
0x58: 0 0100.5e00.0006 0 RCV IP multicast
0x5B: 0 0100.5e00.0005 0 RCV IP multicast
0x65: 0 0011.2130.b344 0 RCV Interface MAC address
0xC0: 0 0100.0ccc.cccc 0 RCV CDP
0xC2: 0 0180.c200.0000 0 RCV IEEE spanning tree
POS0
Routed protocols on POS0:
ip
Bridged protocols on POS0:
clns ip
Software MAC address filter on POS0
Hash Len Address Matches Act Type
0x00: 0 ffff.ffff.ffff 9 RCV Physical broadcast
0x58: 0 0100.5e00.0006 0 RCV IP multicast
0x5B: 0 0100.5e00.0005 1313 RCV IP multicast
0x61: 0 0011.2130.b340 38 RCV Interface MAC address
0x61: 1 0011.2130.b340 0 RCV Bridge-group Virtual Interface
0x65: 0 0011.2130.b344 0 RCV Interface MAC address
0xC0: 0 0100.0ccc.cccc 224 RCV CDP
0xC2: 0 0180.c200.0000 0 RCV IEEE spanning tree
POS1
SPR1
Bridged protocols on SPR1:
clns ip
Software MAC address filter on SPR1
Hash Len Address Matches Act Type
0x00: 0 ffff.ffff.ffff 0 RCV Physical broadcast
0x60: 0 0011.2130.b341 0 RCV Interface MAC address
0x65: 0 0011.2130.b344 0 RCV Interface MAC address
0xC0: 0 0100.0ccc.cccc 0 RCV CDP
0xC2: 0 0180.c200.0000 0 RCV IEEE spanning tree
Table 18-1 describes significant fields shown in the display.
Feedback