Before You Begin
Before performing any of the following procedures, investigate all alarms and clear any trouble conditions. Refer to the Cisco ONS 15454 Troubleshooting Guide as necessary.
This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).
1. A88 Modify Line Settings and PM Parameter Thresholds for Electrical Cards—As needed, complete this procedure to change line and threshold settings for all electrical cards (EC-1, DS-1, DS-3, DS3i-N-12, and DS3XM).
2. A89 Modify Line Settings and PM Parameter Thresholds for Optical Cards—As needed, complete this procedure to change line and threshold settings for all optical cards.
3. A118 Modify Alarm Interface Controller–International Settings—As needed, complete this procedure to change external alarms and controls and/or orderwire settings.
4. A91 Upgrade DS-1 and DS-3 Protect Cards from 1:1 Protection to 1:N Protection—As needed, complete this procedure to change the protection type on DS-1 or DS-3 cards.
5. A315 Modify Port Settings and PM Parameter Thresholds for FC_MR-4 Cards—As needed, complete this procedure to change FC_MR-4 card port and threshold settings.
6. A321 Change Card or PPM Service State—As needed, complete this procedure to change the service state on a card or pluggable port module (PPM).
7. A322 Manage Pluggable Port Modules—As needed, complete this procedure to provision a multirate PPM, assign the optical line rate, change the optical line rate, and delete PPMs.
8. A346 Provision the Soak Timer for an ML-Series Card—As needed, complete this procedure to provision the soak timer for an ML-Series card.
9. A352 View PPM Information on the LCD—As needed, complete this procedure to view wavelength and rate for a PPM on a multirate optical card.
10. A354 Set or Check Cross-Connect Mode for XC-VXC-10G Cards—As needed, complete this procedure to provision the node’s cross-connect mode if mixed mode grooming is required.
NTP-A88 Modify Line Settings and PM Parameter Thresholds for Electrical Cards
Purpose |
This procedure changes the line and threshold settings for electrical cards. |
Tools/Equipment |
None |
Prerequisite Procedures |
A17 Install the Electrical Cards |
Required/As Needed |
As needed |
Onsite/Remote |
Onsite or remote |
Security Level |
Provisioning or higher |
Caution
Changing card settings can be service affecting. You should make all changes during a scheduled maintenance window.
Step 1 Complete the A60 Log into CTC at the node where you want to change the electrical card settings. If you are already logged in, proceed to Step 2.
Step 2 As needed, complete the A108 Back Up the Database.
Step 3 Perform any of the following tasks as needed:
Step 4 As needed, complete the A108 Back Up the Database.
Stop. You have completed this procedure.
NTP-A89 Modify Line Settings and PM Parameter Thresholds for Optical Cards
Purpose |
This procedure changes the line and threshold settings for optical (OC-N) cards. |
Tools/Equipment |
None |
Prerequisite Procedures |
A16 Install Optical Cards and Connectors |
Required/As Needed |
As needed |
Onsite/Remote |
Onsite or remote |
Security Level |
Provisioning or higher |
Caution
Changing card settings can be service affecting. You should make all changes during a scheduled maintenance window.
Step 1 Complete the A60 Log into CTC at the node where you want to change the OC-N card settings. If you are already logged in, proceed to Step 2.
Step 2 As needed, complete the A108 Back Up the Database.
Step 3 Perform any of the following tasks as needed:
Step 4 As needed, complete the A108 Back Up the Database.
Stop. You have completed this procedure.
NTP-A118 Modify Alarm Interface Controller–International Settings
Step 1 Complete the A60 Log into CTC at the node where you want to change the AIC-I card settings. If you are already logged in, continue with Step 2.
Step 2 As needed, complete the A108 Back Up the Database.
Step 3 Perform any of the following tasks as needed:
Step 4 As needed, complete the A108 Back Up the Database.
Stop. You have completed this procedure.
NTP-A91 Upgrade DS-1 and DS-3 Protect Cards from 1:1 Protection to 1:N Protection
Purpose |
This procedure converts DS-1 and DS-3 protect cards from 1:1 to 1:N protection. |
Tools/Equipment |
None |
Prerequisite Procedures |
A71 Create a 1:1 Protection Group |
Required/As Needed |
As needed |
Onsite/Remote |
Onsite or remote |
Security Level |
Provisioning or higher |
Step 1 Complete the A60 Log into CTC at the node where you want to convert the DS-1 or DS-3 cards from 1:1 to 1:N protection. If you are already logged in, continue with Step 2.
Step 2 As needed, complete the A108 Back Up the Database.
Step 3 Perform any of the following tasks as needed:
Step 4 As needed, complete the A108 Back Up the Database.
Stop. You have completed this procedure.
NTP-A315 Modify Port Settings and PM Parameter Thresholds for FC_MR-4 Cards
Purpose |
This procedure changes the line and threshold settings for storage area network (SAN) cards, including the FC_MR-4. |
Tools/Equipment |
None |
Prerequisite Procedures |
A274 Install the FC_MR-4 Card |
Required/As Needed |
As needed |
Onsite/Remote |
Onsite or remote |
Security Level |
Provisioning or higher |
Caution
Changing card settings can be service affecting. You should make all changes during a scheduled maintenance window.
Step 1 Complete the A60 Log into CTC at the node where you want to change the OC-N card settings. If you are already logged in, continue with Step 2.
Step 2 As needed, complete the A108 Back Up the Database.
Step 3 Perform any of the following tasks as needed:
Step 4 As needed, complete the A108 Back Up the Database.
Stop. You have completed this procedure.
NTP-A321 Change Card or PPM Service State
Purpose |
This procedure changes a card or port’s service state, which is an autonomously generated state that gives the overall condition of the port. |
Tools/Equipment |
None |
Prerequisite Procedures |
Chapter 2, “Install Cards and Fiber-Optic Cable” |
Required/As Needed |
As needed |
Onsite/Remote |
Onsite or remote |
Security Level |
Provisioning or higher |
Note On the OC192-XFP, MRC-12, and MRC-2.5G-4 cards, the PPM is equivalent to an optical port.
Step 1 Complete the A60 Log into CTC at the node where you want to change the card service state.
Step 2 From node view, click the Inventory tab.
Step 3 Choose an Administrative state from the Admin State drop-down list for the card or PPM that you want to change: IS (In-Service) or OOS,MT (Out-of-Service,Maintenance).
Step 4 Click Apply.
Step 5 If an error message appears indicating that the card state cannot be changed from its current state, click OK.
Depending on the Administrative state that you choose, the card or port/PPM transitions to a different service state. For more information about the service states and card state transitions, refer to the “Administrative and Service States” appendix of the Cisco ONS 15454 Reference Manual.
Stop. You have completed this procedure.
NTP-A322 Manage Pluggable Port Modules
Step 1 Complete the A60 Log into CTC at the node where you want to provision, change, or delete PPMs. If you are already logged in, continue with Step 2.
Step 2 From the View menu, choose Go to Network View.
Step 3 Click the Alarms tab:
a. Verify that the alarm filter is not turned on. See the A227 Disable Alarm Filtering as necessary.
b. Verify that no unexplained conditions appear on the network. If unexplained conditions appear, resolve them before continuing. Refer to the Cisco ONS 15454 Troubleshooting Guide.
c. Complete the A532 Export CTC Data to export alarm and condition information.
Step 4 As needed, complete the A574 Provision a PPM on the MRC-12 or MRC-2.5G-4 Card. Single-rate PPMs do not require provisioning.
Step 5 As needed, complete the A575 Provision the Optical Line Rate on the MRC-12 or MRC-2.5G-4 Card to assign an OC-3, OC-12, or OC-48 line rate to a multirate PPM.
Step 6 As needed, complete the A576 Change the Optical Line Rate on the MRC-12 or MRC-2.5G-4 Card to change the line rate on a multirate PPM. You cannot change the optical line rate on single-rate PPMs.
Step 7 As needed, complete the A577 Delete a PPM from the MRC-12, MRC-2.5G-4, or OC192-XFP Card.
Stop. You have completed this procedure.
NTP-A346 Provision the Soak Timer for an ML-Series Card
Purpose |
This procedure provisions the soak timer for ports on an ML-Series card. The soak period is the amount of time that the ML-Series port remains in the Down state after an error-free signal is continuously received before transitioning to the Up state. |
Tools/Equipment |
None |
Prerequisite Procedures |
A246 Install Ethernet Cards and Connectors |
Required/As Needed |
As needed |
Onsite/Remote |
Onsite or remote |
Security Level |
Provisioning or higher |
Step 1 Complete the A60 Log into CTC at the node where you want to provision the soak timer for an ML-Series card. If you are already logged in, continue with Step 2.
Step 2 In node view, double-click the ML-Series card that you want to provision.
Step 3 Click the Provisioning tab.
Step 4 Click the Ether Ports or POS Ports subtab and complete the following:
- PSAS—In the appropriate port row, check this check box to enable Pre-Service Alarm Suppression (PSAS), which suppresses all alarms on the port for the time designated in the Soak Time column.
- Soak Time—In the same row, choose the desired soak time (in hours and minutes). Use this column when you have checked PSAS to suppress alarms. When the port detects a signal, the countdown begins for the designated soak time. Soak time hours can be set from 0 to 48. Soak time minutes can be set from 0 to 45 in 15 minute increments.
Step 5 Click Apply.
Stop. You have completed this procedure.
NTP-A352 View PPM Information on the LCD
Purpose |
This procedure displays the line rate and the configured reach for OC-N and MRC cards (MRC-12, MRC-2.5G-4) on the LCD, located on the front of the fan-tray assembly. |
Tools/Equipment |
None |
Prerequisite Procedures |
A16 Install Optical Cards and Connectors |
Required/As Needed |
As needed |
Onsite/Remote |
Onsite or remote |
Security Level |
Provisioning or higher |
Step 1 On the ONS 15454 front panel, repeatedly press the Slot button until the slot number of the card where the PPM resides appears on the LCD.
Step 2 Repeatedly press the Port button. When you see “Status - Lambda” display on the LCD, press the Status button to select that option.
Step 3 Press Status to toggle between “Lambda” and “Line Rate and Reach.”
Step 4 Press Status to select one of those options.
Step 5 Press the Port button as needed to display the information about the desired port.
Stop. You have completed this procedure.s
NTP-A354 Set or Check Cross-Connect Mode for XC-VXC-10G Cards
Purpose |
This procedure is used to set or verify cross-connect mode provisioning required for mixed grooming mode. |
Tools/Equipment |
None |
Prerequisite Procedures |
None |
Required/As Needed |
As needed |
Onsite/Remote |
Onsite or remote |
Security Level |
Provisioning or higher |
Step 1 Complete the A60 Log into CTC at the node where you want to change the XC-VXC-10G card settings. If you are already logged in, continue with Step 2.
Step 2 Navigate to the node view in CTC.
Step 3 Click Provisioning > Cross-Connect. The Cross-Connect dialog box is displayed.
Step 4 If necessary, click the Mixed Mode radio button in the Cross-Connect dialog box and click Apply.
Stop. You have completed this procedure.