Product Overview
This chapter provides an overview of the features available for the Cisco IR829 Integrated Services Routers (ISRs) and contains the following sections:
NOTE : For compliance and safety information, see Regulatory Compliance and Safety Information for Cisco 800 Series Routers.
General Description
The Cisco IR829 Integrated Services Router, part of the Cisco Integrated Services Routers Generation 2 (ISR G2) Family, is designed as a next generation ruggedized fixed form factor router. It is a a small-form factor cellular router targeting mobile/vehicle applications and includes WiFi to provide connectivity in non-carpeted IT spaces, Industrials, Utilities, Transportation, Infrastructure, Industrial M2M application, and asset monitoring.
The IR829 comes in two models, single LTE modem and dual LTE modems.
Cisco IR829 Integrated Services Router shows the IR829.
Cisco IR829 Front Panel Single Modem shows the front panel details of the Cisco IR829 Single Modem.
1 |
CELLULAR 0 AUX |
5 |
Serial Ports |
2 |
mSATA SSD Slot |
6 |
USB 2.0 type-A Port |
3 |
Gigabit WAN (SFP) |
7 |
Power Input, Battery, and Ignition connector. Refer to the DC Power section for pin-outs. |
4 |
Gigabit Ethernet LAN/PoE (RJ45) |
8 |
WLAN ANT 0 2.4GHz |
Cisco IR829 Front Panel Dual Modem shows the front panel details of the Cisco IR829 Dual Modem.
1 |
CELLULAR 0 AUX |
5 |
Serial Ports |
2 |
Limited Modularity Slot |
6 |
USB 2.0 type-A Port |
3 |
Gigabit WAN (SFP) |
7 |
Power Input, Battery, and Ignition connector. Refer to the DC Power section for pin-outs. |
4 |
Gigabit Ethernet LAN/PoE (RJ45) |
8 |
WLAN ANT 0 2.4/5GHz |
Cisco IR829 Back Panel Single Modem shows the back panels details of the Cisco IR829 Single Modem.
1 |
WLAN ANT 0 5GHz |
5 |
Denotes SIM card order, SIM0 on top and SIM1 on bottom. |
2 |
WLAN ANT 1 2.4GHz |
6 |
WLAN ANT 1 5GHz |
3 |
Cover over SIM cards, reset button and console port cover, see Behind the SIM Door |
7 |
CELLULAR 0 MAIN |
4 |
GPS SMA |
Cisco IR829 Back Panel Dual Modem shows the back panels details of the Cisco IR829 Dual Modem.
1 |
Cellular 1 Main |
5 |
Denotes SIM card order, SIM0 on top and SIM1 on bottom. |
2 |
WLAN ANT 1 2.4/5GHz |
6 |
Cellular 1 AUX |
3 |
Cover over SIM cards, reset button and console port cover, see Behind the SIM Door |
7 |
CELLULAR 0 MAIN |
4 |
GPS SMA |
NOTE : Behind the SIM Door Assembly, there is a reset switch(1 ), Mini USB console port(2 ), and Dual SIM slots(3 ). See Behind the SIM Door for details
Cisco IR829 Top Cover (single modem version) shows the top of the Cisco IR829.
Cisco IR829 LED Detail shows the LED detail from the Dual Modem SKU. Single Modem SKUs will only have Cellular 0 LEDs.
The following section shows a detailed description of the LEDs.
LEDs
The following table describes the LEDs for the Cisco IR829.
LED |
Activity |
Description |
---|---|---|
PWR |
Power Status |
In normal operating mode, after system boots. (typically about 2 minutes) Off — No power Green Steady on — Router is reachable, and all interfaces are up and functioning properly Green Flashing — Router is reachable, and no interface is in a failed state Amber Steady on — Router is unreachable (An external interface of the router, that prevents the router from being remotely managed, is in a critical failed state) Amber Flashing — Router is reachable, but at least one of the interfaces is in a non-critical failed state (functionality of that interface is affected) In bootup mode (during the first 60 seconds after powerup) Green Steady on — Router is booting Amber Steady on — Router has a system hardware failure In ROMMON mode: Amber Steady on — Router is in bootup phase or in ROM Monitor mode. |
POE |
POE Power Supply Status |
Off — No -54V PoE power supply detected or no PoE board installed Green Steady on — 54V POE power supply good and all powered port operating normally Amber Steady on — 54V POE power supply good, but one or more POE ports has a fault. |
VPN |
VPN |
Off — No VPN tunnel Steady on — At least one VPN tunnel is up |
GE0 WAN |
Link Status |
Off — No link Steady on — Link is up Flashing — Transmitting and Receiving data |
GPS |
GPS Status |
Off — GPS not configured On — GPS configured Slow Flash — GPS Acquiring in Standalone GPS Fast Flash — GPS Acquiring in Assisted GPS Slow Flash is defined as the LED will be on for 0.25 seconds and off for 0.75 seconds.Fast Flash s defined as the LED will be on for 0.25 seconds and off for 0.25 seconds. |
MOD |
LED 0 LED 1 (not used) |
LED 0 is used for the SKUs that support mSATA Off - Power off or no mSATA detected Green Steady on — mSATA detected |
Ethernet LAN Switch PortsGE1-GE4]Single LED per Port |
Link Status/POE Status |
Off — No link Green Steady on — Link is up Green Flash — Transmitting and Receiving data Amber — POE Fault, implies no link |
WLAN |
2.4GHz 5GHz |
Flashing Green — Radio is down, Bootloader, IOS Ethernet Initialization, IOS Start Up after system initialization. Green to Red to Amber — Discovery/Join process. Rapid Flashing Green — Joined to a controller Steady Green — One wireless client is associated. Flashing or Steady Red — The embedded AP803 inside the IR829 has reported a hardware or software problem. |
CELLULAR0/CELLULAR1 |
RSSI |
The RSSI LEDs are a 3 LED bar graph to indicate signal strength. Their functionality is described in the RSSI LED figure below. |
CELLULAR0/CELLULAR1 |
ACT |
Off — Module not powered on On — Module is powered on and connected but not transmitting or receiving Slow Flash — Module is powered on and searching for connection Fast Flash — Module is transmitting or receiving. |
SIM0/SIM1 |
Sim cards |
Off — No USIM Green — USIM installed and active |
RSSI |
RSSI (2) |
RSSI (1) |
RSSI (0) |
---|---|---|---|
Green |
Green |
Green/Amber |
|
< -110dBm |
Off |
Off |
Off |
-110 to -90dBm |
Off |
Off |
On - Amber |
-90 to -75dBm |
Off |
Off |
On - Green |
-75 to -60dBm |
Off |
On - Green |
On - Green |
> -60dBm |
On - Green |
On - Green |
On - Green |
Memory
The Cisco IR829 uses flash memory and main memory. The flash memory contains the Cisco IOS software image and the boot flash contains the ROMMON boot code. All memory components are factory default and not upgradeable by the end user.
Table 1 shows the memory allocation.
Memory |
Capacity |
---|---|
DDR |
2GB |
Boot ROM |
16MB |
System Flash |
4GB |
SKU Information
Table 1 lists the different SKUs available for the Cisco ISRs. All SKUs support external antenna.
SKU |
LTE |
Dual LTE |
PoE |
mSATA SSD |
Availability |
---|---|---|---|---|---|
IR829GW-LTE-VZ-AK9 |
Yes |
No |
Optional |
No |
US - Verizon |
IR829GW-LTE-NA-AK9 |
Yes |
No |
Optional |
No |
US (AT&T) and Canada |
IR829GW-LTE-GA-*K9 |
Yes |
No |
Optional |
No |
Europe |
IR829GW-LTE-LA-*K9 |
Yes |
No |
Optional |
No |
LATAM and APJC |
IR829B-LTE-EA-*K9 |
Yes |
No |
No |
No |
North America and Europe |
IR829M-LTE-EA-*K9 |
Yes |
No |
Yes |
Yes |
North America and Europe |
IR829M-2LTE-EA-*K9 |
Yes |
Yes |
Yes |
Yes |
North America and Europe |
IR829M-LTE-LA-ZK9 |
Yes |
No |
Yes |
Yes |
Australia, New Zealand and Brazil |
IR829-2LTE-EA-*K9 |
Yes |
Yes |
Optional |
No |
North America and Europe |
For detailed product information, see the Cisco 829 Industrial Integrated Services Routers Data Sheet .
Hardware Features
This section provides an overview of the following hardware features for the Cisco IR829.
Platform Features for Cisco IR829
The following lists the hardware platform features for the Cisco IR829.
- Intel Atom Dual-Core Rangeley CPU, 1250 MHz
- 2GB DDR3 memory capacity
- 16MB SPI BIOS NOR flash
- 8GB (4GB usable) “eMMC” bulk storage flash
- 4-port GE LAN switch, optional PoE 802.3at (30W max) for Cisco devices only.
NOTE : The software does not support PoE negotiation over LLDP, only CDP. Therefore, PoE will only power up Cisco devices,
- WAN 1 GE SFP
-
WWAN /WLAN
- 2 internal mini PCIe slots for 3G/4G/LTE modems, dual SIM — 2 external SIM card slots
- Single 802.11 a/b/g/n WiFi radio with MIMO support.
- Optional Limited Modularity (BYOI) slot
- One RJ45 RS232 DTE serial port
- One RJ45 RS232 DCE/RS485 serial port
- One USB 2.0 Type A external port
- One mini USB type B connector for console
- Lithium Ion battery backed-up RTC
- External Reset/Recovery Push Button
-
External Power
- Direct-wire 12/24VDC vehicle charging system input (9 — 32VDC)
- 4-pin locking power connector
- External GPS SMA Connector
- Six External TNC/RP-TNC connectors (depends on the configuration) for connection to WWAN /WLAN internal modules
- Class A EMC compliance
- RoHS6 compliance
-
Mechanical
- Fanless operation
- Form-factor with no cable cover = 11.00” x 7.70” x 1.73” (WDH)
- Horizontal, Vertical, wall, floor, cabinet-mount and shelf-mount
Wi-Fi
Table 1 shows the different Wi-Fi domains associated with the SKUs.
SKU |
Country |
Wi-Fi Domain |
Cellular Carrier |
---|---|---|---|
IR829GWR-LTE-LA-QK9 |
Japan |
Q |
NTT, DoCoMo, Softbank, KDDI |
IR829GW-LTE-LA-DK9 |
India |
D |
N/A |
IR829GW-LTE-LA-ZK9 |
Australia, New Zealand |
Z |
Telstra, Spark |
IR829GW-LTE-LA-KK9 |
Korea |
K |
N/A |
IR829GW-LTE-LA-HK9 |
China |
H |
N/A |
IR829GW-LTE-LA-LK9 |
Malaysia |
L |
N/A |
IR829GW-LTE-LA-SK9 |
Hong Kong |
S |
N/A |
IR829GW-LTE-LA-NK9 |
Panama |
N |
N/A |
IR829GW-LTE-NA-AK9 |
North America |
A |
AT&T |
IR829GW-LTE-VZ-AK9 |
North America |
A |
Verizon |
IR829GW-LTE-GA-EK9 |
Global |
E |
Global |
IR829GW-LTE-GA-ZK9 |
Australia |
A |
Australia |
Reset Button
The Reset button resets the router configuration to the default configuration set by the factory. To restore the router configuration to the default configuration set by the factory, use a standard size #1 paper clip with wire gauge 0.033 inch or smaller and simultaneously press the reset button while applying power to the router.
NOTE : The rear cover must be removed to expose the reset switch.
NOTE : Before performing a write erase and reboot on the IR829, review the details in the Cisco IR800 Integrated Services Router Software Configuration Guide. The IR829 differs from traditional IOS routers.
Antennas
The IR829 has RP-TNC connectors for Wi-Fi and TNC connectors for cellular. The IR829 also has an SMA connector for a GPS antenna.
Standard antennas are:
- Two multiband swivel-mount dipole antennae (ANT-4G-DP-IN-TNC) and one extender (4G-AE010-R).
- WLAN: Three Cisco Multiband Swivel-Mount Dipole Antennae. (AIR-ANTM2050D-R) for WLAN functionality.
For detailed information about Cisco Antennas, please refer to the following guides:
Cisco Industrial Routers Antenna Guide:
Cisco Aironet Antennas and Accessories Reference Guide
Antennas and Installation Scenarios
NOTE : Before choosing your antenna type and installation scenario, read through the following information.
Coexistence of radio standards:
When operating and planning installation of products with WiFi, 4G LTE, and GPS wireless standards coexisting on the IR829 platform, the user needs to provision greater than 15dB isolation between the WiFi and LTE antennas at all frequencies of 4G LTE and WiFI operation for minimum impact to performance.
Ideally, isolation should be 20-25dB or more. Specifically, users should not install 4G LTE dipoles and WiFi dipoles on the chassis at the same time, since doing so would generally result in less than 15dB isolation and may have a strong impact on performance depending on frequency bands in question.
Vehicular 5-in-1 and 2-in-1 installation and deployment notes
In the section that follows, the 5-in-1 antenna refers to ANT-5-4G2WL2G1-O, and 2-in-1 antenna refers to ANT-2-WLAN-D-O.
Installation
Users need to provision a 8 x 8" flat mounting surface with a mounting hole on the roof of the vehicle for the 5-in-1 antenna, and a 6 x 6" flat mounting surface with a mounting hole for the 2-in-1 WiFi antenna. Without a flat mounting surface, the antenna will not meet IP67 standards and may have reduced service life.
Ground plane
Cisco recommends having a 1 foot ground plane under both the 5-in-1 and 2-in-1 antennas. In case of a metal vehicle roof, the roof itself shall be the ground plane. While Cisco has investigated the effects of ground plane and no ground plane, wireless performance was certified with the 1 foot ground plane.
Isolation between 5-in-1 and 2-in-1 antennas
Cisco recommends 18" inch spacing between the 5-in-1 and the 2-in-1 antenna centers for optimal isolation.
Cisco recommends routing the 2.4GHz WLAN ports of the IR829 to the 2-in-1 antenna, and the 5GHz ports to the 5-in-1 antenna to optimize isolation between WiFi 2.4 GHz and cellular 4G LTE. The 5-in-1 antenna has been fully optimized for WiFI and cellular LTE coexistence and isolation. Connecting the 2.4GHz WiFi signals to a separate antenna simply allows to user to optimize the antenna isolation further. Both the 5-in-1 and 2-in-1 are dual band WiFi capable and fully support both 2.4 GHz or 5GHz WLAN signals.
MIMO ports on 5-in-1 and 2-in-1
Cellular and WLAN ports on the 5-in-1 and 2-in-1 antennas support MIMO technology. MIMO brings significant improvements in throughput and robustness of the wireless link in fading channels. Users choosing to connect only one wireless port on MIMO capable products are giving up significant wireless performance in both throughput and robustness of the link.
- The individual 4G antenna cables on the 5-in-1 antenna can be connected to either cellular port of IR829. There is no one-to-one assignment requirement.
- The individual WLAN antenna cables on the 5-in-1 antenna and the 2-in-1 antenna can be connected to any WLAN port of IR829. There is no one to one assignment requirement.
The following section shows some examples of different installation scenarios.
Modem Support
The Cisco IR800 series Industrial routers use the MC73XX and MC74XX series modems. The software download page can be found here:
https://software.cisco.com/download/navigator.html?mdfid=286288566&flowid=76082
NOTE : Be sure to select the correct firmware download for your carrier.
The Cisco Firmware Upgrade Guide for Cellular Modems can be found here:
http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/firmware/Firmware_Upgrade.html
Previous versions of this guide contained additional configuration information which has now been relocated to the Cisco IR800 Integrated Services Router Software Configuration Guide.
Supported Cisco Antennas and Cables
4G/LTE Radio Cables/Antennas
4G/LTE Radio Cables/Antennas Use Case 1
Item |
Description |
---|---|
Antenna Arrangement |
Front Panel Swivel Mount 4G-LTE dipoles |
Indoor Cable |
Chose one of 3 scenarios:
|
Adapter and/or Lightning Arrestor |
None |
External Cable |
None |
Antenna |
Quantity of 2 4G Indoor Swivel Mount Dipole, 0 dBi, TNC(m), white
|
4G/LTE Radio Cables/Antennas Use Case 2
Item |
Description |
---|---|
Antenna Arrangement |
1' 2', 5', 10', 15' or 20' cable to mast mounted antenna, Stick Omni or Directional Flat Panel antenna |
Indoor Cable |
None, router located in outdoor protective enclosure |
Adapter and/or Lightning Arrestor |
None |
External Cable |
RA-TNC(m) to N(m), LMR-400-DB, 20', qty 2
|
Antenna |
2x 4G Omni Stick, Standard Perf, 10” 2dBi, 1x N(f) each
1x 4G Panel Antenna, 2x N(f) each
|
4G/LTE Radio Cables/Antennas Use Case 3
Item |
Description |
---|---|
Antenna Arrangement |
1' 2', 5', 10', 15' or 20' cable to mast mounted antenna, Stick Omni or Directional Flat Panel antenna |
Indoor Cable |
R/A-TNC(m) to N(m), LMR-240-FR/CMR, 2’, qty 2 R/A-TNC(m) to N(m), LMR-240-FR/CMR, 1', qty 2 R/A-TNC(m) to N(m), LMR-240-FR/CMR, 5', qty 2 R/A-TNC(m) to N(m), LMR-240-FR/CMR, 10', qty 2 R/A-TNC(m) to N(m), LMR-240-FR/CMR, 15', qty 2 R/A-TNC(m) to N(m), LMR-240-FR/CMR, 20', qty 2 Note : These cables not available from Cisco |
Adapter and/or Lightning Arrestor |
None |
External Cable |
None |
Antenna |
1x 4G Panel Antenna, 2x N(f) each
|
4G/LTE Radio Cables/Antennas Use Case 4
Item |
Description |
---|---|
Antenna Arrangement |
Front Panel Swivel Mount 4G-LTE dipoles |
Indoor Cable |
Chose one of 3 scenarios:
|
Adapter and/or Lightning Arrestor |
None |
External Cable |
None |
Antenna |
Quantity of 2 4G Indoor Swivel Mount Dipole, 0 dBi, TNC(m), white
|
4G/LTE Radio Cables/Antennas Use Case 4
Item |
Description |
---|---|
Antenna Arrangement |
Front Panel Swivel Mount 4G-LTE dipoles |
Indoor Cable |
Chose one of 3 scenarios:
|
Adapter and/or Lightning Arrestor |
None |
External Cable |
None |
Antenna |
Quantity of 2 4G Indoor Swivel Mount Dipole, 0 dBi, TNC(m), black
|
4G/LTE Radio Cables/Antennas Use Case 5
Item |
Description |
---|---|
Antenna Arrangement |
2x ceiling mount 4G-LTE antennas |
Indoor Cable |
None |
Adapter and/or Lightning Arrestor |
None |
External Cable |
None |
Antenna |
Quantity of 2 4G Indoor omni-directional Ceiling Mount 2 dBi,
Quantity of 2 4G Dipole Ceiling Mount 2 dBi
|
4G/LTE Radio Cables/Antennas GPS Use Case 1
Item |
Description |
---|---|
Antenna Arrangement |
GPS Antenna with Integrated 15' coax cable, Mounted to top of Utility Cabinet Roof SMA(f), qty 1 |
Indoor Cable |
None |
Adapter and/or Lightning Arrestor |
None |
External Cable |
None |
Antenna |
GPS Antenna Need one with integrated coax cable and SMA(m) connector, 17ft, outdoor, IP67 Quantity of 1
|
Single Band Cisco WiFi Antenna
Supported Single Band Cisco WiFi Antenna Use Case 1
Item |
Description |
---|---|
Antenna Arrangement |
Single Band, Front Panel Mounted Antennas |
Radio Module |
Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors: 4x RP-TNC (jack) |
Adapter and/or Lightning Arrestor |
N/A |
Indoor Cable |
N/A |
External Cable |
N/A |
Antenna |
2x Single Band, Swivel Mount Omni, RP-TNC(plug), 2.2dBi @ 2.4 GHz
2x Single Band, Swivel Mount Omni, RP-TNC(plug), 3.5dBi @ 5 GHz
|
Supported Single Band Cisco WiFi Antenna Use Case 2
Item |
Description |
---|---|
Antenna Arrangement |
Single Band, Single Element, Ceiling Mounted Antennas |
Radio Module |
Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors: 4x RP-TNC (jack) |
Adapter and/or Lightning Arrestor |
N/A |
Indoor Cable |
Choose one of 2:
|
External Cable |
N/A |
Antenna |
2x Single Band, Ceiling Mount Omni, 36” LONG RG-58 cable with RP-TNC (plug), 5.2dBi @ 2.4 GHz
2x Single Band, Ceiling Mount Omni, 36" LONG RG-58 cable with RP-TNC (plug), 5.2dBi @ 5 GHz
|
Supported Single Band Cisco WiFi Antenna Use Case 3
Item |
Description |
---|---|
Antenna Arrangement |
2.4 GHz, Dual Element, 5 GHz Single Element, Ceiling Mounted Antennas |
Radio Module |
Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors: 4x RP-TNC (jack) |
Adapter and/or Lightning Arrestor |
N/A |
Indoor Cable |
Choose one of 2:
|
External Cable |
N/A |
Antenna |
1x Single Band, Ceiling Mount Omni, Dual Element, 36" LONG RG-58 cable with RP-TNC, 2.0dBi @ 2.4 GHz
2x Single Band, Ceiling Mount Omni, 36" LONG RG-58 cable with RP-TNC (plug), 5.2dBi @ 5 GHz
|
Supported Single Band Cisco WiFi Antenna Use Case 4
Item |
Description |
---|---|
Antenna Arrangement |
Single Band, Dual Element, Wall Mounted Antennas |
Radio Module |
Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors: 4x RP-TNC (jack) |
Adapter and/or Lightning Arrestor |
None, or: RP-TNC lightning arrestor, qty 4
|
Indoor Cable |
None |
External Cable |
Choose one of 4:
|
Antenna |
1x Single Band, Dual Element, Wall Mount Patch, 18" LONG RG-58 cable with RP-TNC, 6.5dBi @ 2.4 GHz
1x Single Band, Dual Element, Wall Mount Omni, 18" LONG RG-58 cables with RP-TNC, 4.5dBi @ 5 GHz (INDOOR ONLY)
— OR 1x Single Band, Dual Element, Wall Mount Patch, 18" LONG RG-58 cables with RP-TNC, 7.0dBi @ 5 GHz (INDOOR/OUTDOOR)
|
Supported Single Band Cisco WiFi Antenna Use Case 5
Item |
Description |
---|---|
Antenna Arrangement |
Single Band, Dual Element, Wall Mounted Patch, Indoor/ Outdoor Antennas |
Radio Module |
Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors: 4x RP-TNC (jack) |
Adapter and/or Lightning Arrestor |
N(f) to N(f), RF-adapter, qty 4
|
Indoor Cable |
None |
External Cable |
RP-TNC(plug) to N(m)-R/A, LMR-240-DB, 5', qty 4
|
Antenna |
1x Single Band, Dual Element, Wall Mount Patch, 18" LONG RG-58 cable with N(m), 13dBi @ 2.4 GHz
1x Single Band, Dual Element, Wall Mount Patch, 18" LONG RG-58 cable with N(m), 14dBi @ 5 GHz
|
Dual Band Cisco WiFi Antenna
Supported Dual Band Cisco WiFi Antenna Use Case 1
Item |
Description |
---|---|
Antenna Arrangement |
Dual Band Front Panel Mounted Antennas |
Radio Module |
Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors: 4x RP-TNC (jack) |
Adapter and/or Lightning Arrestor |
N/A |
Indoor Cable |
N/A |
External Cable |
N/A |
Antenna |
2x Dual Band, Swivel Mount Omni, RP-TNC(plug), 2dBi @ 2.4 GHz, 4dBi @ 5 GHz
|
Supported Dual Band Cisco WiFi Antenna Use Case 2
Item |
Description |
---|---|
Antenna Arrangement |
Dual Band Front Panel Mounted Antennas |
Radio Module |
Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors: 2x RP-TNC (jack) |
Adapter and/or Lightning Arrestor |
N/A |
Indoor Cable |
N/A |
External Cable |
N/A |
Antenna |
1x Dual Band, Dual Element per Band, Omni, 18" LONG RG-58 cables with RP-TNC (plug), 2.0dBi @ 2.4 GHz (2 ports), 3.0dBi @ 5 GHz (2 ports)
|
Supported Dual Band Cisco WiFi Antenna Use Case 3
Item |
Description |
---|---|
Antenna Arrangement |
Dual Band Front Panel Mounted Antennas |
Radio Module |
Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors: 2x RP-TNC (jack) |
Adapter and/or Lightning Arrestor |
N(f) to N(f), RF-adapter, qty 2
|
Indoor Cable |
N/A |
External Cable |
RP-TNC(plug) to N(m)-R/A, LMR-240-DB, 5', qty 2
|
Antenna |
2x Dual Band, Swivel Mount Omni, RP-TNC(plug), 2dBi @ 2.4 GHz, 4dBi @ 5 GHz
|
7 in 1 Antenna Configuration for Transportation
Transportation Use Case 1
Antenna Arrangement
7 x RF ports, with the IR829 deployed in a transportation application.
(Default Configuration)
Quinta 5-in-1 antenna AND a WiFi 2-in-1 antenna to utilize all 7 ports.
The 5-in1 Quinta antenna and the 2-in1 WiFi antennas need to be separated 18" between mounting hole centers of the two antennas.
Extension Cable
No extension cables are required if the IR829 is located within ~1.0ft of 5-in-1 antenna, and ~2.0ft of WiFi 2-in-1 antenna.
If these conditions are not met, this deployment requires the following extension cables:
Cellular extension cables (2 ports)
Qty 2X LMR-400-DB TNC(m)-R/A - TNC(f), 5ft
- 4G-CAB-LMR400-5
— OR
Qty 2X LMR-400-DB TNC(m)-R/A - TNC(f), 10ft
- G-CAB-LMR400-10
— OR
Qty 2X LMR-400-LLPL plenum / indoor only TNC(m)-R/A - TNC(f), 20ft
- 4G-CAB-ULL-20
WiFi 2.4 GHz / 5GHz extension cables (4 ports, can mix and match lengths per installation requirements if needed) Qty 4x LMR-400-DB RPTNC(plug) - STR RPTNC(jack) - STR, 5ft
- AIR-CAB005LL-R
— OR
Qty 4x LMR-400-DB RPTNC(plug)-R/A RPTNC(jack)-STR, 10ft
- CAB-L400-10-R
— OR
Qty 4x LMR-400-DB RPTNC(plug)-STR RPTNC(jack)-STR, 20ft
- AIR-CAB020LL-R
— AND
GPS port
No extension cable required, 5-in-1 antenna comes with integrated active GPS antenna with 17ft cable.
Antenna
Quinta 5 element 5-in-1 transportation antenna, black radome color, 2x 4G cellular, 2x dual band WiFi, 1xGPS
- ANT-5-4G2WL2G1-O
- 07-100261-01
Has the following integrated cables:
qty 2 x cellular, LMR-195, 2ft long, TNC(m)
qty 2 x WiFi, 2ft long, LMR-195 RPTNC (plug)
qty 1 x GPS, RG-174, 17ft long, SMA(m)
— AND
WiFi 2-in-1 2 element 2 in 1 transportation antenna, black radome color, 2x dual band WiFi
- ANT-2-WLAN-D-O
Has the following integrated cables:
qty 2 x WiFi, 3ft long, LMR-240 RPTNC (plug)
Transportation Use Case 2
Antenna Arrangement
7 x RF ports, with the IR829 deployed in a transportation application.
(Alternate Configuration, can be used in case the application calls for the WiFi antennas to be separate from the LTE antenna for example. a ceiling mount WLAN).
This case describes a Tercia 3-in-1 transportation antenna (which covers MIMO cellular and GPS) together with qty 2 x 2-in-1 WiFi antennas.
NOTE : A custom ceiling mount bracket is required for the 2-in-1 antenna if installed in a ceiling mount configuration (NOT SUPPLIED BY CISCO)
Extension Cable
No extension cables are required if the IR829 is located within ~1.0ft of 5-in-1 antenna, and ~2.0ft of WiFi 2-in-1 antenna.
If these conditions are not met, this deployment requires the following extension cables:
Cellular extension cables (2 ports)
Qty 2X LMR-400-DB TNC(m)-R/A - TNC(f), 5ft
- 4G-CAB-LMR400-5
— OR
Qty 2X LMR-400-DB TNC(m)-R/A - TNC(f), 10ft
- G-CAB-LMR400-10
— OR
Qty 2X LMR-400-LLPL plenum / indoor only TNC(m)-R/A - TNC(f), 20ft
- 4G-CAB-ULL-20
WiFi 2.4 GHz / 5GHz extension cables (4 ports, can mix and match lengths per installation requirements if needed) Qty 4x LMR-400-DB RPTNC(plug) - STR RPTNC(jack) - STR, 5ft
- AIR-CAB005LL-R
— OR
Qty 4x LMR-400-DB RPTNC(plug)-R/A RPTNC(jack)-STR, 10ft
- CAB-L400-10-R
— AND
GPS port - No extension cable required, 3-in-1 antenna comes with integrated active GPS antenna with 17ft cable.
Antenna
Quinta 5 element 5-in-1 transportation antenna, black radome color, 2x 4G cellular, 2x dual band WiFi, 1xGPS
- ANT-5-4G2WL2G1-O
Has the following integrated cables:
- qty 2 x cellular, LMR-195, 2ft long, TNC(m)
- qty 2 x WiFi, 2ft long, LMR-195 RPTNC (plug)
- qty 1 x GPS, RG-174, 17ft long, SMA(m)
— AND
WiFi 2-in-1 2 element 2 in 1 transportation antenna, black radome color, 2x dual band WiFi
- ANT-2-WLAN-D-O
Has the following integrated cables:
- qty 2 x WiFi, 3ft long, LMR-240 RPTNC (plug)
Power Supply
The Cisco IR829 comes with an external power connector.
- Direct-wire 12/24VDC vehicle charging system input (9 — 32VDC).
- 4-pin locking Molex power connector, Cisco part number 29-2562-01.
There is an external AC to DC power adapter for the IR829. It meets ITE standards and operating temperature range of -20C to 60C, but is not suited for industrial environment. Part Number is IR829-PWR125W-AC.
There is a 12.5 feet power cable available to order. Part Number is IR829-DC-PWRCORD.
SFP Modules
The router Ethernet SFP modules provide connections to other devices. These field-replaceable transceiver modules provide the uplink interfaces. Local connectors (LCs) provide the fiber-optic connection. RJ-45 connectors allow copper connections. You can use any combination of the supported SFP modules listed in the table that follows.
Type of SFP Module |
Model |
---|---|
Rugged and Industrial SFPs–40 to 185°F (–40 to 85°C) |
GLC-SX-MM-RGD with digital optical monitoring (DOM) support GLC-LX-SM-RGD with digital optical monitoring (DOM) support GLC-ZX-SM-RGD with digital optical monitoring (DOM) support |
Commercial SFPs 32° to 158°F (0° to 70°C) |
GLC-SX-MM GLC-LH-SM GLC-BX-U, with Digital Optical Monitoring (DOM) support GLC-BX-D, with Digital Optical Monitoring (DOM) support CWDM-SFP, with Digital Optical Monitoring (DOM) support DWDM-SFP, with Digital Optical Monitoring (DOM) support |
Extended Temperature SFP 23° to 185°F (-5° to 85°C) |
SFP-GE-S, with Digital Optical Monitoring (DOM) support SFP-GE-L, with Digital Optical Monitoring (DOM) support SFP-GE-Z, with Digital Optical Monitoring (DOM) support GLC-SX-SMD GLC-LH-SMD GLC-EX-SMD GLC-TE GLC-FE-100LX-RGD GLC-FE-100FX-RGD |
Copper SFP Supported on IOS 15.6(3)M but GE only |
GLC- T (0 to 70°C) SFP-GE-T (-5 to 85°C) |
NOTE : The WAN port GE0 can accept either fiber SFP or Copper SFP modules. The speed is fixed at 100Mbps or 1Gbps depending on the SFP installed. Since there is no I-temp copper SFP available in the market, there is no Copper SFP supported. In order to use a Copper SFP, you must enter service internal mode, and enter “unsupported transceivers”. Then unplug and insert the Copper SFP again.
NOTE: Speed and duplex commands are not available on the GE0 WAN interface.
The following two Copper SFPs (non I-temp) will be officially supported at 1Gbps:
-
Copper SFP - GLC- T
- Copper 1Gbps, (0 to 70°C), CPN is 30-1410-04
-
Copper SFP - SFP-GE-T
- Copper 1Gbps, (-5 to 85°C), CPN is 30-1421-02
Additional SFPs with added support are:
-
GLC-FE-100LX-RGD
- Fiber (fixed speed of 100Mbps)
-
GLC-FE-100FX-RGD
- Fiber (fixed speed of 100Mbps)
-
GLC-TE
- Copper (fixed speed of 1Gbps)
-
GLC-FE-T=
- Copper 100Mbps
NOTE: Auto negotiation is not supported on these SFPs.
For minimum software requirements, refer to the Release Notes for your platform.
For the most up-to-date list of supported SFP models for Cisco Industrial Ethernet switches, see http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_6981.html#wp138176
Serial RJ45 Ports
Two RJ45 serial ports are provided to control and monitor RS232 or RS485 equipment. Serial port 0 can be configured for either RS232 DCE or RS485 half or full duplex. Serial port 1 can be configured for RS232 DTE only.
The RJ45 connector orientation as it appears on the router is shown in RJ45 connector.
The RJ45 pinouts are shown in RJ45 Pinouts
Serial Port Characteristics
Figure #con_1195004__ shows the characteristics of the S0 and S1 ports.
RS232 | RS485 Full Duplex | RS485 Half Duplex | ||||||
---|---|---|---|---|---|---|---|---|
Pin # |
Signal Description |
Abbr. |
S0 (DCE) |
S1 (DTE) |
Signal |
DIR |
Signal |
DIR |
1 |
DCE Ready, used as DSR in IOS |
DSR/RI |
output |
input |
TX+ |
output |
TX/RX+ |
<-> |
2 |
Received Line Signal Detector |
DCD |
output |
input |
TX- |
output |
TX/RX- |
<-> |
3 |
DTE Ready |
DTR |
input |
output |
RX- |
input |
||
4 |
Signal Ground |
COM |
COM |
COM |
||||
5 |
Received Data |
RxD |
output |
input |
||||
6 |
Transmitted Data |
TxD |
input |
output |
RX+ |
input |
||
7 |
Clear To Send |
CTS |
output |
input |
||||
8 |
Request To Send |
RTS |
input |
output |
Cisco refers to the signal on pin 1 as DSR. Use the show interface async 0 (or 1) from the IOS command line will give you the state of the modem control signals on the last line:
DCD=up DSR=up DTR=down RTS=down CTS=up
Note : The Serial 0 and Serial 1 pin out is different from the Console/Auxiliary port, do NOT use the RJ-45 to DB-9 Blue colored Console Cable (72-3383-01).
DTE to DCE
While the equipment shown in Traditional DTE to DCE concept is less common today, the concept of DTE (Data Terminal Equipment) and DCE (Data Communication Equipment) comes from the use of dial-up modems that were used on the telephone network until the late 1990’s.
Data Circuits |
Control Circuits |
Voltage |
---|---|---|
0 (space) |
Asserted |
+3 to +15 V |
1 (mark) |
Deasserted |
-15 to -3 V |
Note : Circuits must tolerate voltages of + / - 15 V with respect to a ground reference and be able to withstand indefinite short circuit to ground. Minimum outputs for the IR809 and IR829 are +/- 5 V.
RS232 Port
The RS232 signal names in #con_1195004__ apply to both Serial 0 and Serial 1 ports on the IR809 and IR829. It is the direction of the data and flow control signals that differs. The RS232-DCE port, Serial 0, is designed to be connected to a far-end DTE port, or to another DCE port via a crossover (null-modem) cable. The RS232-DTE port, Serial 1 is designed to be connected to a far-end DCE port, or to another DTE port via a crossover (null-modem) cable.
CAUTION : please read the following three caution statements.
- This port is not shared with the Console port as is seen on some routers and switches in the Cisco Enterprise Portfolio where a console is provided that can be accessed both via USB and RS232 delivered on an RJ-45 style physical port.
- The pinout is also different from the connector pinout that was used for a Cisco RS232 console delivered on an RJ-45 style physical port.
- Serial 0 and Serial 1 use EIA-561 standard for RS-232 signals on an RJ-45 style physical port. This means the “baby blue” colored Cisco Serial Console Cable (72-3383-01) WILL NOT WORK .
RS232 is Point to Point – DTE to DCE
EIA/TIA-561 Pin Layout with a DB9 Connector
The pinouts are shown in DB9 pinout
DB9 Female connector viewed from the front. Plugs into the PC.
8P8C plug, commonly referred to as RJ45. Plugs into controlled equipment.
EIA/TIA-561 Pin Layout with a DB25 Connector
The pinouts are shown in DB25 pinout
DB25 Female connector viewed from the front. Plugs into the PC.
8P8C plug, commonly referred to as RJ45. Plugs into controlled equipment.
EIA/TIA-561 Pin Layout and RS-232 pin assignments
Note : The cable pinouts shown in EIA/TIA-561 Pin Layout with a DB25 Connector and EIA/TIA-561 Pin Layout with a DB9 Connector illustrate pin 1 on the RJ45 connector connecting to pin 6 on the DB9/DB25 connector.
Table 1 shows the pin layout and signal assignment for both the DB9 and RS-232 plugs.
8P8C (RJ45) |
DB9 |
DB25 |
Signal |
Description |
---|---|---|---|---|
1 |
6 or 9 |
6 or 22 |
RI Ready (Used as DSR in IOS) |
Ring Indicator, (used as DSR in IOS) Optional use. |
2 |
1 |
8 |
DCD |
Data Carrier Detect |
3 |
4 |
20 |
DTR |
Data Terminal Ready |
4 |
5 |
7 |
SG (COM) |
Signal Ground (Common) |
5 |
2 |
3 |
RXD |
Received Data |
6 |
3 |
2 |
TXD |
Transmitted Data |
7 |
8 |
5 |
CTS |
Clear To Send |
8 |
7 |
4 |
RTS |
Request To Send |
Serial 0 configured as an RS485 Port
The RS232 pin out follows the EIA-561 standard, however, there is no standard for an RJ-45 connector used for RS485. In the IR809 and IR829, the pin-pairs 1,2 and 3,6 were chosen for RS485 so that an Ethernet CAT-5 with the standard twisted-pair pin assignments can be used.
Note : RS485 usually requires 120 Ohm terminators at each end of the bus but there may be variations that depend upon the cable type.
The following are some of the common RS485 characteristics:
-
Electrical
- Same signal levels as RS-422 except the topology is implemented as a bus rather than point-to-point
- A – B (differential signal) < -0.3V = MARK = OFF = logical 1
- A – B (differential signal) > +0.3V = SPACE = ON = logical 0
-
Implications
- When RS485 is implemented as a bus, effectively, this is a form of a LAN and requires a higher level protocol. As a bus technology, you must have a protocol that controls access to the media vs. point-to-point where you can simply stream individual asynchronous characteristics.
- Since higher level protocol are used and the technology is primarily a LAN, no MODEM control signals are implemented in RS485.
2 Wire RS485 (Half Duplex)
Characteristics of a 2 wire, or Half Duplex RS485 connection include:
- Bus cable with a max. length of 1200 m (4000 ft) depending upon cable quality and speed of the data
- Stub cable with a max. of 5 meters
- Multi-master capability similar to coaxial cable based Ethernet
- Inverted line is generally indicated by the index "A" or "-" (TX/RX-)
- Non-inverted line designated as "B" or "+” (TX/RX+)
- Except for trivially short point to point connections, terminating resistors are generally required.
- A ground wire is also normally used in addition to what is shown in 2 Wire RS485 (Half Duplex)
1 |
Failsafe Bias Resistor |
5 |
Device Cable (Maximum of 5 m) |
2 |
Terminating Resistor |
6 |
|
3 |
RS485 Device |
7 |
|
4 |
Bus Cable 1200m (4000 ft.) |
4 Wire RS485 (Full Duplex)
Characteristics of a 4 wire, or Full Duplex RS485 connection include:
- Bus cable with a max. length of 1200 m (4000 ft) depending upon cable quality and speed of the data
- Stub cable of max. 5 meters
- Master/slave applications
- Inverted line is generally indicated by the index "A" or "-"
- Non-inverted line designated as "B" or "+”
- Except for trivially short point to point connections, terminating resistors are generally required.
- A ground wire is also normally used in addition to what is shown in 4 Wire RS485 (Full Duplex)
1 |
Failsafe Bias Resistor |
5 |
Device Cable (Maximum of 5 m) |
2 |
Terminating Resistor |
6 |
RS485 Slave |
3 |
RS485 Master |
7 |
|
4 |
Bus Cable 1200m (4000 ft.) |
Wiring Recommendations for RS-485 Networks:
- Typically Category 5 Ethernet cable is suitable for RS-485.
- Shielded cable is desirable and the shield should be grounded at on end if it is used.
- Half Duplex - one pair shall be used for TX/RX+ and TX/RX- signals (orange and white/orange) and one wire for GND (blue).
- Full Duplex - one pair shall be used for RX+ and RX- signals (green and white/green), one pair shall be used for TX+ and TX- signals (orange and white/orange), and one wire for GND (blue).
- Unused wires should be terminated with 100 ohm resistors to ground at both ends of the cable using your chosen wire termination method, e.g. screw terminals, punch down blocks, etc. This will help to avoid undesirable inductive pickup in the unused conductors.
RS485 Termination Resistors
The following are some best practices when using terminating resistors:
- When the bit time is not substantially longer than the loop time of the cable, termination is crucial for minimizing reflections. (Speed for the signal to go the length of the cable and reflect back)
- If the bit time is substantially longer than the loop time of the cable, you can usually get by without terminating resistors as can be observed with short point to point cables at lower baud rates.
- For standard termination, you would match the termination resistor value with the differential-mode characteristic impedance of the cabling on both ends of the network. Typically 120 Ohm.
- No 120 Ohm terminations are used on the other multi-drop ports in the middle of the network, only at the two far ends of the network.
RS485 Failsafe Resistors
The following are some best practices when using failsafe resistors:
-
When inputs are between -200mV and +200mV, receiver output is "undefined". There are four common fault conditions that result
in the undefined receiver output that can cause erroneous data:
- All transmitters in a system are in shutdown.
- The receiver is not connected to the cable.
- The cable has an open.
- The cable has a short.
- Fail-safe biasing is used to keep the receiver's output in a defined state when one of these conditions occurs.
- The fail-safe biasing consists of a pull-up resistor on the non-inverting line and a pull-down resistor on the inverting line.
- With proper biasing, the receiver will output a valid high when any one of the fault conditions occurs.
- Fail-safe bias resistors should be placed at the receiver end of the transmission line.
Serial Port Control
The entire layer 1 configuration of the IR809 / IR829 serial ports is done in IOS under the following constructs. The following example shows values other than the defaults to show most of the IOS keywords.
interface Async0 (or Async 1)
no ip address
encapsulation relay-line
line 1 (or line 2)
transport preferred none
transport input all
transport output all
databits 7
parity odd
stopbits 1
speed 1200
Note : To allow an IOx application to control the serial port parameters (set baud rate, data bits, parity, stop bits), you must use the “propagation” keyword as shown in the following example:
IR800#conf t
Enter configuration commands, one per line. End with CNTL/Z.
IR800(config)#relay line 1 1/5 ?
propagation Allow virtual serial port to control the parameters
<cr>
IR800(config)#relay line 1 1/5 propagation
Virtual Serial Ports
Line 1/5 and 1/6 are the Linux serial ports viewed from IOS
line 1/5 1/6
transport preferred none
transport input all
transport output all
The physical and virtual ports are then linked by the following constructs:
relay line 1 1/5
relay line 2 1/6
- The serial devices, line 1/5 and 1/6, in IOS are instantiated in IOx as /dev/ttyS1 and /dev/ttyS2.
- The IOx serial device on the Linux host can then be exposed to an application container.
The port mapping from the physical port though IOS to the IOx would appear as in Port Mappings:
To switch Serial 0 from RS232 to RS485, the configuration is set in interface Async0. The RS485 half or full duplex is set there as well. For example:
RS485 HALF DUPLEX - Serial 0 Only:
interface Async0 no ip address
encapsulation relay-line half-duplex
media-type rs485
RS485 FULL DUPLEX - Serial 0 Only:
interface Async0 no ip address
encapsulation relay-line full-duplex (
<- default– will not print for a “show run” command
)
media-type rs485
Additional Resources
How Far and How Fast Can You Go with RS-485:
https://www.maximintegrated.com/en/app-notes/index.mvp/id/3884
Interface Circuits for TIA/EIA-232-F – Design Notes:
http://www.ti.com/lit/an/slla037a/slla037a.pdf
RS232 Quick Guide
http://cds.linear.com/docs/en/product-selector-card/RS232%20Quick%20Guide.pdf