MPLS Multilink PPP Support

The MPLS Multilink PPP Support feature ensures that MPLS Layer 3 Virtual Private Networks (VPNs) with quality of service (QoS) can be enabled for bundled links. This feature supports Multiprotocol Label Switching (MPLS) over Multilink PPP (MLP) links in the edge (provider edge [PE]-to-customer edge [CE]) or in the MPLS core (PE-to-PE and PE-to-provider [P] device).

Service providers that use relatively low-speed links can use MLP to spread traffic across them in their MPLS networks. Link fragmentation and interleaving (LFI) should be deployed in the CE-to-PE link for efficiency, where traffic uses a lower link bandwidth (less than 768 kbps). The MPLS Multilink PPP Support feature can reduce the number of Interior Gateway Protocol (IGP) adjacencies and facilitate load sharing of traffic.

Prerequisites for MPLS Multilink PPP Support

  • Multiprotocol Label Switching (MPLS) must be enabled on provider edge (PE) and provider (P) devices

Restrictions for MPLS Multilink PPP Support

  • Only 168 multilink bundles can be created per the OC-3 interface module on the router.

  • The maximum number of members per multilink bundle is 16.

For information on how to configure, Protocol-Field-Compression (PFC) and Address-and-Control-Field-Compression (AFC), see the Configuring PPP and Multilink PPP chapter in this book.

Information About MPLS Multilink PPP Support

MPLS Layer 3 Virtual Private Network Features Supported for Multilink PPP

The table below lists Multiprotocol Label Switching (MPLS) Layer 3 Virtual Private Network (VPN) features supported for Multilink PPP (MLP) and indicates if the feature is supported on customer edge-to-provider edge (CE-to-PE) links, PE-to-provider (P) links, and Carrier Supporting Carrier (CSC) CE-to-PE links.

Table 1. MPLS Layer 3 VPN Features Supported for MLP

MPLS L3 VPN Feature

CE-to-PE Links

PE-to-P Links

CSC CE-to-PE Links

Static routes

Supported

Not supported

Not supported

External Border Gateway Protocol (eBGP)

Supported

Not applicable to this configuration

Supported

Intermediate System-to-Intermediate System (IS-IS)

Not supported

Supported

Not supported

Open Shortest Path First (OSPF)

Supported

Supported

Not supported

Enhanced Interior Gateway Routing Protocol (EIGRP)

Supported

Supported

Not supported

Interprovider interautonomous (Inter-AS) VPNs (with Label Distribution Protocol [LDP])

Not applicable to this configuration

Supported (MLP between Autonomous System Boundary Routers [ASBRs])

Not applicable to this configuration

Inter-AS VPNs with IPv4 Label Distribution

Not applicable to this configuration

Supported (MLP between ASBRs)

Not applicable to this configuration

CSC VPNs (with LDP)

Not supported

Not applicable to this configuration

Supported

CSC VPNs with IPv4 label distribution

Supported

Not applicable to this configuration

Supported

External and internal BGP (eiBGP) Multipath

Not supported

Not supported

Not applicable to this configuration

Internal BGP (iBGP) Multipath

Not applicable to this configuration

Not supported

Not applicable to this configuration

eBGP Multipath

Not supported

Not supported

Not supported

MPLS Quality of Service Features Supported for Multilink PPP

The table below lists the Multiprotocol Label Switching (MPLS) quality of service (QoS) features supported for Multilink PPP (MLP) and indicates if the feature is supported on customer edge-to-provider edge (CE-to-PE) links, PE-to-provider (P) links, and Carrier Supporting Carrier (CSC) CE-to-PE links.

Table 2. MPLS QoS Features Supported for MLP

MPLS QoS Feature

CE-to-PE Links

PE-to-P Links

CSC CE-to-PE Links

Default copy of IP Precedence to EXP bits and the reverse

Supported

Not supported

Not supported

Set MPLS EXP bits using the modular QoS Command-Line Interface (MQC)

Supported

Supported

Supported

Matching on MPLS EXP using MQC

Supported

Supported

Supported

Low Latency Queueing (LLQ)/Class-Based Weighted Fair Queueing (CBWFQ) support

Supported

Supported

Supported

Weighted Random Early Detection (WRED) based on EXP bits using MQC

Supported

Supported

Supported

Policer with EXP bit-marking using MQC-3 action

Supported

Supported

Supported

Support for EXP bits in MPLS accounting

Supported

Supported

Supported

MPLS Multilink PPP Support and PE-to-CE Links

The figure below shows a typical Multiprotocol Label Switching (MPLS) network in which the provider edge (PE) device is responsible for label imposition (at ingress) and disposition (at egress) of the MPLS traffic.

In this topology, Multilink PPP (MLP) is deployed on the PE-to-customer edge (CE) links. The Virtual Private Network (VPN) routing and forwarding instance (VRF) interface is in a multilink bundle. There is no MPLS interaction with MLP; all packets coming into the MLP bundle are IP packets.

The PE-to-CE routing protocols that are supported for the MPLS Multilink PPP Support feature are external Border Gateway Protocol (eBGP), Open Shortest Path First (OSPF), and Enhanced Interior Gateway Routing Protocol (EIGRP). Static routes are also supported between the CE and PE devices.

Quality of service (QoS) features that are supported for the MPLS Multilink PPP Support feature on CE-to-PE links are link fragmentation and interleaving (LFI), compressed Real-Time Transport Protocol (cRTP), policing, marking, and classification.

MPLS Multilink PPP Support and Core Links

The figure below shows a sample topology in which Multiprotocol Label Switching (MPLS) is deployed over Multilink PPP (MLP) on provider edge-to-provider (PE-to-P) and P-to-P links. Enabling MPLS on MLP for PE-to-P links is similar to enabling MPLS on MLP for P-to-P links.

Figure 1. MLP on PE-to-P and P-to-P Links

You employ MLP in the PE-to-P or P-to-P links primarily so that you can reduce the number of Interior Gateway Protocol (IGP) adjacencies and facilitate the load sharing of traffic.

In addition to requiring MLP on the PE-to-P links, the MPLS Multilink PPP Support feature requires the configuration of an IGP routing protocol and the Label Distribution Protocol (LDP).

MPLS Multilink PPP Support in a CSC Network

The figure below shows a typical Multiprotocol Label Switching (MPLS) Virtual Private Network (VPN) Carrier Supporting Carrier (CSC) network where Multilink PPP (MLP) is configured on the CSC customer edge (CE)-to-provider edge (PE) links.

Figure 2. MLP on CSC CE-to-PE Links with MPLS VPN Carrier Supporting Carrier

The MPLS Multilink PPP Support feature supports MLP between CSC-CE and CSC-PE links with the Label Distribution Protocol (LDP) or with external Border Gateway Protocol (eBGP) IPv4 label distribution. This feature also supports link fragmentation and interleaving (LFI) for an MPLS VPN CSC configuration. The figure below shows all MLP links that this feature supports for CSC configurations.

Figure 3. MLP Supported Links with MPLS VPN Carrier Supporting Carrier

MPLS Multilink PPP Support in an Interautonomous System

The figure below shows a typical Multiprotocol Label Switching (MPLS) Virtual Private Network (VPN) interautonomous system (Inter-AS) network where Multilink PPP (MLP) is configured on the provider edge-to-customer edge (PE-to-CE) links.

Figure 4. MLP on ASBR-to-PE Links in an MPLS VPN Inter-AS Network

The MPLS Multilink PPP Support feature supports MLP between Autonomous System Boundary Router (ASBR) links for Inter-AS VPNs with Label Distribution Protocol (LDP) and with external Border Gateway Protocol (eBGP) IPv4 label distribution.

How to Configure MPLS Multilink PPP Support

The tasks in this section can be performed on customer edge-to-provider edge (CE-to-PE) links, PE-to-provider (P) links, P-to-P links, and Carrier Supporting Carrier (CSC) CE-to-PE links.

Enabling Cisco Express Forwarding or Distributed Cisco Express Forwarding

Perform the following task to enable Cisco Express Forwarding or distributed Cisco Express Forwarding.

Before you begin

Multilink PPP (MLP) requires the configuration of Cisco Express Forwarding. Distributed MLP (dMLP) requires the configuration of distributed Cisco Express Forwarding.

Cisco Express Forwarding is enabled by default on most Cisco platforms running Cisco software. To find out if Cisco Express Forwarding is enabled on your platform, enter the show ip cef command. If Cisco Express Forwarding is enabled, you receive output that looks like this: 


Device# show ip cef 
Prefix              Next Hop            Interface
10.2.61.8/24        192.168.100.1       FastEthernet1/0/0
                    192.168.101.1       FastEthernet6/1

If Cisco Express Forwarding is not enabled on your platform, the output for the show ip cef command looks like this: 


Device# show ip cef
%CEF not running

Distributed Cisco Express Forwarding is enabled by default on devices such as the Catalyst 6500 series switch, the Cisco 7500 series router, and the Cisco 12000 series Internet router.

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. Enter one of the following commands:
    • ip cef
    • ip cef distributed
  4. exit

DETAILED STEPS

  Command or Action Purpose
Step 1

enable

Example:


Device> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

Example:


Device# configure terminal

Enters global configuration mode.

Step 3

Enter one of the following commands:

  • ip cef
  • ip cef distributed

Example:


Device(config)# ip cef

Example:


Device(config)# ip cef distributed

Enables Cisco Express Forwarding switching.

or

Enables distributed Cisco Express Forwarding switching.

Step 4

exit

Example:


Device(config)# exit

Returns to privileged EXEC mode.

Creating a Multilink Bundle

Perform this task to create a multilink bundle for the MPLS Multilink PPP Support feature. This multilink bundle can reduce the number of Interior Gateway Protocol (IGP) adjacencies and facilitate load sharing of traffic.

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. interface multilink group-number
  4. ip address address mask [secondary]
  5. encapsulation encapsulation-type
  6. ppp multilink
  7. end

DETAILED STEPS

  Command or Action Purpose
Step 1

enable

Example:


Device> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

Example:


Device# configure terminal

Enters global configuration mode.

Step 3

interface multilink group-number

Example:


Device(config)# interface multilink 1

Creates a multilink bundle and enters multilink interface configuration mode.

  • The group-number argument is the number of the multilink bundle (a nonzero number).

Step 4

ip address address mask [secondary]

Example:


Device(config-if)# ip address 10.0.0.0 255.255.0.0

Sets a primary or secondary IP address for an interface.

  • The address argument is the IP address.

  • The mask argument is the mask for the associated IP subnet.

  • The secondary keyword specifies that the configured address is a secondary IP address. If this keyword is omitted, the configured address is the primary IP address.

This command is used to assign an IP address to the multilink interface.

Step 5

encapsulation encapsulation-type

Example:


Device(config-if)# encapsulation ppp

Sets the encapsulation method as PPP to be used by the interface.

  • The encapsulation-type argument specifies the encapsulation type.

Step 6

ppp multilink

Example:


Device(config-if)# ppp multilink

Enables MLP on an interface.
Step 7

end

Example:


Device(config-if)# end

Returns to privileged EXEC mode.

Assigning an Interface to a Multilink Bundle

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. controller {t1 | e1 } slot/port
  4. channel-group channel-number timeslots
  5. exit
  6. interface serial slot / port : channel-group
  7. ip route-cache [cef | distributed]
  8. no ip address
  9. keepalive [period [retries]]
  10. encapsulation encapsulation-type
  11. ppp multilink group group-number
  12. ppp multilink
  13. ppp authentication chap
  14. end

DETAILED STEPS

  Command or Action Purpose
Step 1

enable

Example:


Device> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

Example:


Device# configure terminal

Enters global configuration mode.

Step 3

controller {t1 | e1 } slot/port

Example:

Configures a T1 or E1 controller and enters controller configuration mode.

  • The t1 keyword indicates a T1 line card.

  • The e1 keyword indicates an E1 line card.

  • The slot/port arguments are the backplane slot number and port number on the interface. Refer to your hardware installation manual for the specific slot numbers and port numbers.

Step 4

channel-group channel-number timeslots

Example:


Device(config-controller)# channel-group 1 timeslots 1

Defines the time slots that belong to each T1 or E1 circuit.

  • The channel-number argument is the channel-group number. When a T1 data line is configured, channel-group numbers can be values from 0 to 23. When an E1 data line is configured, channel-group numbers can be values from 0 to 30.

  • The timeslots range keyword and argument specifies one or more time slots or ranges of time slots belonging to the channel group. The first time slot is numbered 1. For a T1 controller, the time slot range is from 1 to 24. For an E1 controller, the time slot range is from 1 to 31. You can specify a time slot range (for example, 1-29), individual time slots separated by commas (for example 1, 3, 5), or a combination of the two (for example 1-14, 15, 17-31).

Step 5

exit

Example:


Device(config-controller)# exit

Returns to global configuration mode.

Step 6

interface serial slot / port : channel-group

Example:

Configures a serial interface for a Cisco 7500 series router with channelized T1 or E1 and enters interface configuration mode.

  • The slot argument indicates the slot number. Refer to the appropriate hardware manual for slot and port information.

  • The /port argument indicates the port number. Refer to the appropriate hardware manual for slot and port information.

  • The :channel-group argument indicates the channel group number. Cisco 7500 series routers specify the channel group number in the range of 0 to 4 defined with the channel-group controller configuration command.

Step 7

ip route-cache [cef | distributed]

Example:


Device(config-if)# ip route-cache cef

Controls the use of switching methods for forwarding IP packets.

  • The cef keyword enables Cisco Express Forwarding operation on an interface after Cisco Express Forwarding operation was disabled.

  • The distributed keyword enables distributed switching on the interface.

Step 8

no ip address

Example:


Device(config-if)# no ip address

Removes any specified IP address.

Step 9

keepalive [period [retries]]

Example:


Device(config-if)# keepalive

Enables keepalive packets and specifies the number of times that the Cisco software tries to send keepalive packets without a response before bringing down the interface or before bringing the tunnel protocol down for a specific interface.

  • The period argument is an integer value, in seconds, greater than 0. The default is 10.

  • The retries argument specifies the number of times that the device continues to send keepalive packets without a response before bringing the interface down. Enter an integer value greater than 1 and less than 255. If you do not enter a value, the value that was previously set is used; if no value was specified previously, the default of 5 is used.

If you are using this command with a tunnel interface, the command specifies the number of times that the device continues to send keepalive packets without a response before bringing the tunnel interface protocol down.

Step 10

encapsulation encapsulation-type

Example:


Device(config-if)# encapsulation ppp

Sets the encapsulation method used by the interface.

  • The encapsulation-type argument specifies the encapsulation type. The example specifies PPP encapsulation.

Step 11

ppp multilink group group-number

Example:


Device(config-if)# ppp multilink group 1

Restricts a physical link to join only one designated multilink group interface.

  • The group-number argument is the number of the multilink bundle (a nonzero number).

Step 12

ppp multilink

Example:


Device(config-if)# ppp multilink

Enables MLP on the interface.

Step 13

ppp authentication chap

Example:


Device(config-if)# ppp authentication chap

(Optional) Enables Challenge Handshake Authentication Protocol (CHAP) authentication on the serial interface.

Step 14

end

Example:


Device(config-if)# end

Returns to privileged EXEC mode.

Disabling PPP Multilink Fragmentation

Perform this task to disable PPP multilink fragmentation. PPP multilink fragmentation is enabled by default.

Enabling fragmentation reduces the delay latency among bundle links, but adds some load to the CPU. Disabling fragmentation might produce better throughput.

If your data traffic is consistently of a similar size, we recommend disabling fragmentation. In this case, the benefits of fragmentation can be outweighed by the added load on the CPU.

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. interface type number
  4. ppp multilink fragmentation disable
  5. end

DETAILED STEPS

  Command or Action Purpose
Step 1

enable

Example:


Device> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

Example:


Device# configure terminal

Enters global configuration mode.

Step 3

interface type number

Example:


Device(config)# interface serial 1/0/0

Configures an interface type and enters interface configuration mode.

  • The type argument indicates the type of interface to be configured.

  • The number argument specifies the port, connector, or interface card number. The numbers are assigned at the factory at the time of installation or when the interface is added to a system, and they can be displayed with the show interfaces command.

Step 4

ppp multilink fragmentation disable

Example:


Device(config-if)# ppp multilink fragmentation disable

Disables packet fragmentation.

Step 5

end

Example:


Device(config-if)# end

Returns to privileged EXEC mode.

Verifying the Multilink PPP Configuration

SUMMARY STEPS

  1. enable
  2. show ip interface brief
  3. show ppp multilink
  4. show ppp multilink interface interface-bundle
  5. show interface type number
  6. show mpls forwarding-table
  7. exit

DETAILED STEPS

Step 1

enable

Enables privileged EXEC mode. Enter your password if prompted.

Example:


Device> enable
Device#
Step 2

show ip interface brief

Verifies logical and physical Multilink PPP (MLP) interfaces.

Example:
Step 3

show ppp multilink

Verifies that you have created a multilink bundle.

Example:
Step 4

show ppp multilink interface interface-bundle

Displays information about a specific MLP interface.

Example:
Step 5

show interface type number

Displays information about serial interfaces in your configuration.

Example:


Device# 


  Hardware is Multichannel T1
  MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation PPP, LCP Open, multilink Open, crc 16, Data non-inverted
  Last input 00:00:01, output 00:00:01, output hang never
  Last clearing of "show interface" counters 00:47:13
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     722 packets input, 54323 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     697 packets output, 51888 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 output buffer failures, 0 output buffers swapped out
     1 carrier transitions no alarm present
  Timeslot(s) Used:1, subrate: 64Kb/s, transmit delay is 0 flags
  Transmit queue length 25

Device# 


  Hardware is Multichannel T1
  MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation PPP, LCP Open, multilink Open, crc 16, Data non-inverted
  Last input 00:00:03, output 00:00:03, output hang never
  Last clearing of "show interface" counters 00:47:16
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     725 packets input, 54618 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     693 packets output, 53180 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 output buffer failures, 0 output buffers swapped out
     1 carrier transitions no alarm present
  Timeslot(s) Used:2, subrate: 64Kb/s, transmit delay is 0 flags
  Transmit queue length 26

You can also use the show interface command to display information about the multilink interface:

Example:


Device# show interface multilink6

Multilink6 is up, line protocol is up
  Hardware is multilink group interface
  Internet address is 10.30.0.2/8
  MTU 1500 bytes, BW 128 Kbit, DLY 100000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation PPP, LCP Open, multilink Open
  Open: CDPCP, IPCP, TAGCP, loopback not set
  DTR is pulsed for 2 seconds on reset
  Last input 00:00:00, output never, output hang never
  Last clearing of "show interface" counters 00:48:43
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  30 second input rate 0 bits/sec, 0 packets/sec
  30 second output rate 0 bits/sec, 0 packets/sec
     1340 packets input, 102245 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     1283 packets output, 101350 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 output buffer failures, 0 output buffers swapped out
     0 carrier transitions
Step 6

show mpls forwarding-table

Displays contents of the Multiprotocol Label Switching (MPLS) Label Forwarding Information Base (LFIB). Look for information on multilink interfaces associated with a point2point next hop.

Example:


Device# show mpls forwarding-table

Local  Outgoing    Prefix            Bytes tag  Outgoing   Next Hop
tag    tag or VC   or Tunnel Id      switched   interface
16     Untagged    10.30.0.1/32      0          Mu6        point2point
17     Pop tag     10.0.0.3/32       0          Mu6        point2point
18     Untagged    10.0.0.9/32[V]    0          Mu10       point2point
19     Untagged    10.0.0.11/32[V]   6890       Mu10       point2point
20     Untagged    10.32.0.0/8[V]    530        Mu10       point2point
21     Aggregate   10.34.0.0/8[V]    0
22     Untagged    10.34.0.1/32[V]   0          Mu10       point2point

Use the show ip bgp vpnv4 command to display VPN address information from the Border Gateway Protocol (BGP) table.

Example:


Device# show ip bgp vpnv4 all summary

BGP router identifier 10.0.0.1, local AS number 100
BGP table version is 21, main routing table version 21
10 network entries using 1210 bytes of memory
10 path entries using 640 bytes of memory
2 BGP path attribute entries using 120 bytes of memory
1 BGP extended community entries using 24 bytes of memory
0 BGP route-map cache entries using 0 bytes of memory
0 BGP filter-list cache entries using 0 bytes of memory
BGP using 1994 total bytes of memory
BGP activity 10/0 prefixes, 10/0 paths, scan interval 5 secs
10.0.0.3  4 100 MsgRc52 MsgSe52  TblV21  0  0 00:46:35 State/P5xRcd
Step 7

exit

Returns to user EXEC mode.

Example:


Device# exit
Device>

Configuration Examples for MPLS Multilink PPP Support

Sample MPLS Multilink PPP Support Configurations

The following examples show sample configurations on a Carrier Supporting Carrier (CSC) network. The configuration of MLP on an interface is the same for provider edge-to-customer edge (PE-to-CE) links, PE-to-provider (P) links, and P-to-P links.

Example: Configuring Multilink PPP on an MPLS CSC PE Device

The following example shows how to configure for Multiprotocol Label Switching (MPLS) Carrier Supporting Carrier (CSC) provider edge (PE) device. 


!
mpls label protocol ldp
ip cef
ip vrf vpn2
 rd 200:1
 route-target export 200:1
 route-target import 200:1
!


!

 no ip address
 encapsulation ppp
 
 ppp multilink
 ppp multilink group 1

interface Multilink1
 ip vrf forwarding vpn2
 ip address 10.35.0.2 255.0.0.0
 no peer neighbor-route
 load-interval 30
 ppp multilink
 ppp multilink interleave
 ppp multilink group 1

!
!
router ospf 200
 log-adjacency-changes
 auto-cost reference-bandwidth 1000
 redistribute connected subnets
 passive-interface Multilink1
 network 10.0.0.7 0.0.0.0 area 200
 network 10.31.0.0 0.255.255.255 area 200
!
!
 router bgp 200
 no bgp default ipv4-unicast
 bgp log-neighbor-changes
 neighbor 10.0.0.11 remote-as 200
 neighbor 10.0.0.11 update-source Loopback0
 !
 address-family vpnv4
 neighbor 10.0.0.11 activate
 neighbor 10.0.0.11 send-community extended
 bgp scan-time import 5
 exit-address-family
 !
 address-family ipv4 vrf vpn2
 redistribute connected
 neighbor 10.35.0.1 remote-as 300
 neighbor 10.35.0.1 activate
 neighbor 10.35.0.1 as-override
 neighbor 10.35.0.1 advertisement-interval 5
 no auto-summary
 no synchronization
 exit-address-family

Example: Enabling Cisco Express Forwarding or Distributed Cisco Express Forwarding

The following example shows how to enable Cisco Express Forwarding for Multilink PPP (MLP) configurations: 


enable
configure terminal 
ip cef

The following example shows how to enable distributed Cisco Express Forwarding for distributed MLP (dMLP) configurations: 


enable
configure terminal 
ip cef distribute

Example: Creating a Multilink Bundle

The following example shows how to create a multilink bundle for the MPLS Multilink PPP Support feature: 


Device(config)# interface multilink 1
Device(config-if)# ip address 10.0.0.0 10.255.255.255
Device(config-if)# encapsulation ppp
Device(config-if)# ppp chap hostname group 1
Device(config-if)# ppp multilink
Device(config-if)# ppp multilink group 1

Example: Assigning an Interface to a Multilink Bundle

The following example shows how to create four multilink interfaces with Cisco Express Forwarding switching and Multilink PPP (MLP) enabled. Each of the newly created interfaces is added to a multilink bundle. 


interface multilink1
 ip address 10.0.0.0 10.255.255.255
 ppp chap hostname group 1
 ppp multilink
 ppp multilink group 1



 no ip address
 encapsulation ppp
 ip route-cache cef
 no keepalive
 ppp multilink
 ppp multilink group 1

 no ip address
 encapsulation ppp
 ip route-cache cef
 no keepalive
 ppp chap hostname group 1
 ppp multilink
 ppp multilink group 1

 no ip address
 encapsulation ppp
 ip route-cache cef
 no keepalive
 ppp chap hostname group 1
 ppp multilink
 ppp multilink group 1

 no ip address
 encapsulation ppp
 ip route-cache cef
 no keepalive
 ppp chap hostname group 1
 ppp multilink
 ppp multilink group 1