Schema - File Event Tables

file_event

Schema: File Event Tables

This chapter contains information on the schema and supported joins for file events. For more information, see the section listed in the following table.

Table 10-1 Schema for File Event Tables
See...	For the table that stores information on...	Version
file_event	File events generated when file transfers are detected in the monitored network.	5.1.1+

While the following tables are available, Cisco does not currently support lookups on them:

file_categories
file_rules
file_types
file_type_rule_map
file_type_category_map

file_event

The file_event table contains information about the file events that your Secure Firewall Management Center generates. A new file event is generated each time a file transfer is detected on the monitored network. Files identified as malware by AMP for Firepower generate both a file event and a malware event. Endpoint-based malware events do not have corresponding file events, and file events do not have AMP for Endpoints-related fields.

For more information, see the following sections:

file_event Fields

The file_event table contains information on files that are detected passing through the monitored network. Each file event can be correlated with a connection event. Details of the file and file transfer are recorded, including the name, size, source, destination, and direction of the file, a SHA256 hash of the file, the device that detected the file, and whether it is considered to be malware.

Table 10-2 file_event Fields
Field	Description
`action`	The action taken on the file based on the file type. Can have the following values: `1` — Detect `2` — Block `3` — Malware Cloud Lookup `4` — Malware Block `5` — Malware Allow List `6` — Cloud Lookup Timeout
`application_id`	ID number that maps to the application using the file transfer.
`application_name`	One of the following: the name of the application used in the connection `pending` or `unknown` if the system cannot identify the application blank if there is no application information in the connection
`archived`	Indicates whether the file has been archived.
`cert_valid_end_date`	The Unix timestamp on which the SSL certificate used in the connection ceases to be valid.
`cert_valid_start_date`	The Unix timestamp when the SSL certificate used in the connection was issued.
`client_application_id`	The internal identification number for the client application, if applicable.
`client_application_name`	The name of the client application, if applicable.
`connection_sec`	UNIX timestamp (seconds since 00:00:00 01/01/1970) of the connection event associated with the file event.
`counter`	Specific counter for the event, used to distinguish among multiple events that happened during the same second.
`direction`	Whether the file was uploaded or downloaded. Currently the value depends entirely on the protocol (for example, if the connection is HTTP it is a download).
`disposition`	The malware status of the file. Possible values include: `CLEAN` — The file is clean and does not contain malware. `UNKNOWN` — It is unknown whether the file contains malware. `MALWARE` — The file contains malware. `UNAVAILABLE` — The software was unable to send a request to the Cisco cloud for a disposition, or the Cisco cloud services did not respond to the request. `CUSTOM SIGNATURE` — The file matches a user-defined hash, and is treated in a fashion designated by the user.
`domain_name`	Name of the domain on which the.event was detected
`domain_uuid`	UUID of the domain on which the event was detected. This is presented in binary.
`dst_continent_name`	The name of the continent of the destination host. `**` — Unknown `na` — North America `as` — Asia `af` — Africa `eu` — Europe `sa` — South America `au` — Australia `an` — Antarctica
`dst_country_id`	Code for the country of the destination host.
`dst_country_name`	Name of the country of the destination host.
`dst_ip_address_v6`	Field deprecated in Version 5.2. Returns `null` for all queries.
`dst_ipaddr`	A binary representation of the IP address of the destination host involved in the triggering event.
`dst_ipaddr_str`	The IP address of the destination host in a human-readable format.
`dst_port`	Port number for the destination of the connection.
`event_description`	The additional event information associated with the event type.
`event_id`	Event identification number.
`file_name`	Name of the detected file. This name can contain UTF-8 characters.
`file_sha`	SHA256 hash of the file.
`file_size`	Size of the detected file in bytes.
`file_type`	The file type of the detected or quarantined file.
`file_type_category`	Description of the file category.
`file_type_category_id`	Numeric identifier for the file category.
`file_type_id`	ID number that maps to the file type.
`http_response_code`	The response code given to the HTTP request in the event.
`instance_id`	Numerical ID of the Snort instance on the managed device that generated the event.
`netmap_num`	Netmap ID for the domain on which the event was detected.
`policy_uuid`	Identification number that acts as a unique identifier for the access control policy that triggered the event.
`sandboxed`	Indicates whether the file was sent for dynamic analysis. Possible values are: `Sent for Analysis` `Failed to Send` `File Size is Too Small` `File Size is Too Large` `Sent for Analysis` `Analysis Complete` `Failure (Network Issue)` `Failure (Rate Limit)` `Failure (File Too Large)` `Failure (File Read Error)` `Failure (Internal Library Error)` `File Not Sent, Disposition Unavailable` `Failure (Cannot Run File)` `Failure (Analysis Timeout)` `File Not Supported`
`score`	A numeric value from `0` to `100` based on the potentially malicious behaviors observed during dynamic analysis.
`security_context`	Description of the security context (virtual firewall) that the traffic passed through. Note that the system only populates this field for ASA FirePOWER devices in multi-context mode.
`sensor_address`	A binary representation of the IP address of the device that provided the event.
`sensor_id`	ID for the device that provided the event.
`sensor_name`	The text name of the managed device that generated the event record. This field is `null` when the event refers to the reporting device itself, rather than to a connected device.
`sensor_uuid`	A unique identifier for the managed device, or `0` if `sensor_name` is `null`.
`signature_processed`	Indicated whether the file’s signature was processed.
`src_continent_name`	The name of the continent of the source host. `**` — Unknown `na` — North America `as` — Asia `af` — Africa `eu` — Europe `sa` — South America `au` — Australia `an` — Antarctica
`src_country_id`	Code for the country of the source host.
`src_country_name`	Name of the country of the source host.
`src_ip_address_v6`	Field deprecated in Version 5.2. Returns `null` for all queries.
`src_ipaddr`	A binary representation of the IPv4 or IPv6 address of the source host involved in the triggering event.
`src_ipaddr_str`	The IP address of the source host in a human-readable format.
`src_port`	Port number for the source of the connection.
`ssl_issuer_common_name`	Issuer Common Name from the SSL certificate. This is typically the host and domain name of the certificate issuer, but may contain other information.
`ssl_issuer_country`	The country of the SSL certificate issuer.
`ssl_issuer_organization`	The organization of the SSL certificate issuer.
`ssl_issuer_organization_unit`	The organizational unit of the SSL certificate issuer.
`ssl_serial_number`	The serial number of the SSL certificate, assigned by the issuing CA.
`ssl_subject_common_name`	Subject Common name from the SSL certificate. This is typically the host and domain name of the certificate subject, but may contain other information.
`ssl_subject_country`	The country of the SSL certificate subject.
`ssl_subject_organization`	The organization of the SSL certificate subject.
`ssl_subject_organization_unit`	The organizational unit of the SSL certificate subject.
`storage`	The storage status of the file. Possible values are: `File Stored` `Unable to Store File` `File Size is Too Large` `File Size is Too Small` `Unable to Store File` `File Not Stored, Disposition Unavailable`
`threat_name`	Name of the threat.
`timestamp`	UNIX timestamp when enough of the file has been transmitted to identify the file type.
`timestamp_str`	The date and time of the file event in human-readable format of `Year-Month-Day Time`. For example, February 4th, 2022 is `2022-02-04 20:18:58.`
`url`	URL of the file source.
`user_id`	The internal identification number for the destination user; that is, the user who last logged into the destination host before the event occurred.
`username`	Name associated with the `user_id`.
`web_application_id`	The internal identification number for the web application, if applicable.
`web_application_name`	Name of the web application, if applicable.

file_event Joins

You cannot perform joins on the file_event table.

file_event Sample Query

The following query returns up to 10 file events with the application name, connection information, and file name, where the disposition is not CLEAN.

SELECT file_event.application_name, file_event.connection_sec, file_event.counter,

file_event.file_name

FROM file_event

WHERE file_event.disposition != "CLEAN" limit 10;

Secure Firewall Management Center Database Access Guide v7.2

Bias-Free Language

Book Title

Secure Firewall Management Center Database Access Guide v7.2

Chapter Title