Catalyst 4500 Series Switch Software Configuration Guide, 12.2(53)SG

Configuring 802.1X Port-Based Authentication

This chapter describes how to configure IEEE 802.1X port-based authentication on the Catalyst 4500 series switch to prevent unauthorized client devices from gaining access to the network.

This chapter includes the following major sections:

•Understanding 802.1X Port-Based Authentication

•Configuring 802.1X Port-Based Authentication

•Displaying 802.1X Statistics and Status

•Displaying Authentication Details

Note For complete syntax and usage information for the switch commands used in this chapter, first look at the Cisco Catalyst 4500 Series Switch Command Reference and related publications at this location:

http://www.cisco.com/en/US/products//hw/switches/ps4324/index.html

If the command is not found in the Catalyst 4500 Series Switch Command Reference, it will be found in the larger Cisco IOS library. Refer to the Catalyst 4500 Series Switch Cisco IOS Command Reference and related publications at this location:

http://www.cisco.com/en/US/products/ps6350/index.html

Understanding 802.1X Port-Based Authentication

802.1X defines 802.1X port-based authentication as a client-server based access control and authentication protocol that restricts unauthorized clients from connecting to a LAN through publicly accessible ports. An authentication server validates each supplicant (client) connected to an authenticator (network access switch) port before making available any services offered by the switch or the LAN.

Note 802.1X support requires an authentication server that is configured for Remote Authentication Dial-In User Service (RADIUS). 802.1X authentication does not work unless the network access switch can route packets to the configured RADIUS server. To verify that the switch can route packets, you must ping the server from the switch.

Until a client is authenticated, only Extensible Authentication Protocol over LAN (EAPOL) traffic is allowed through the port to which the client is connected. After authentication succeeds, normal traffic can pass through the port.

To configure 802.1X port-based authentication, you need to understand the concepts in these sections:

•Device Roles

•802.1X and Network Access Control

•Authentication Initiation and Message Exchange

•Ports in Authorized and Unauthorized States

•802.1X Host Mode

•802.1X Violation Mode

•Using 802.1X with VLAN Assignment

•Using 802.1X for Guest VLANs

•Using 802.1X with MAC Authentication Bypass

•Using 802.1X with Web-Based Authentication

•Using 802.1X with Inaccessible Authentication Bypass

•Using 802.1X with Unidirectional Controlled Port

•Using 802.1X with Authentication Failed VLAN Assignment

•Using 802.1X with Port Security

•Using 802.1X Authentication with ACL Assignments and Redirect URLs

•Using 802.1X with RADIUS-Provided Session Timeouts

•Using 802.1X with Voice VLAN Ports

•Using Multiple Domain Authentication and Multiple Authentication

•How 802.1X Fails on a Port

•Supported Topologies

Device Roles

With 802.1X port-based authentication, network devices have specific roles. Figure 40-1 shows the role of each device, which is described below.

Figure 40-1 802.1X Device Roles

•Client—The workstation that requests access to the LAN, and responds to requests from the switch. The workstation must be running 802.1X-compliant client software.

•Authenticator—Controls physical access to the network based on the authentication status of the client. The Catalyst 4500 series switch acts as an intermediary between the client and the authentication server, requesting identity information from the client, verifying that information with the authentication server, and relaying a response to the client. The switch encapsulates and decapsulates the Extensible Authentication Protocol (EAP) frames and interacts with the RADIUS authentication server.

When the switch receives EAPOL frames and relays them to the authentication server, the Ethernet header is stripped and the remaining EAP frame is reencapsulated in the RADIUS format. The EAP frames are not modified or examined during encapsulation, and the authentication server must support EAP within the native frame format. When the switch receives frames from the authentication server, the frame header is removed from the server, leaving the EAP frame, which is then encapsulated for Ethernet and sent to the client.

Note The Catalyst 4500 series switches must be running software that supports the RADIUS client and 802.1X.

•Authentication server—Performs the actual authentication of the client. The authentication server validates the identity of the client and notifies the switch that the client is authorized to access the LAN and switch services. (The only supported authentication server is the RADIUS authentication server with EAP extensions; it is available in Cisco Secure Access Control Server version 3.2 and later.)

802.1X and Network Access Control

Network Access Control is a feature that allows port access policies to be influenced by the anti-virus posture of the authenticating device.

Anti-virus posture includes such elements as the operating system running on the device, the operating system version, whether anti-virus software is installed, what version of anti-virus signatures is available, etc. If the authenticating device has a NAC-aware 802.1X supplicant and the authentication server is configured to support NAC via 802.1X, anti-virus posture information is automatically included as part of the 802.1X authentication exchange.

For information on NAC, refer to the URL:

http://www.cisco.com/en/US/products/ps6128/index.html

Authentication Initiation and Message Exchange

The switch or the client can initiate authentication. If you enable authentication on a port with the
authentication port-control auto interface configuration command (dot1x port-control auto command in Cisco IOS Release 12.2(46)SG and earlier releases), the switch must initiate authentication when it determines that the port link state has changed. It then sends an EAP-request/identity frame to the client to request its identity (typically, the switch sends an initial identity/request frame followed by one or more requests for authentication information). Upon receipt of the frame, the client responds with an EAP-response/identity frame.

However, if during bootup, the client does not receive an EAP-request/identity frame from the switch, the client can initiate authentication by sending an EAPOL-start frame, which prompts the switch to request the client's identity.

If 802.1X is not enabled or supported on the network access switch, any EAPOL frames from the client are dropped. If the client does not receive an EAP-request/identity frame after three attempts to start authentication, the client transmits frames as if the port is in the authorized state. A port in the authorized state means that the client has been successfully authenticated. When the client supplies its identity, the switch begins its role as the intermediary, passing EAP frames between the client and the authentication server until authentication succeeds or fails. If the authentication succeeds, the switch port becomes authorized.

The specific exchange of EAP frames depends on the authentication method being used. Figure 40-2 shows a message exchange that is initiated by the client using the One-Time Password (OTP) authentication method with an authentication server.

Figure 40-2 Message Exchange

Ports in Authorized and Unauthorized States

The switch port state determines whether the client is granted access to the network. The port starts in the unauthorized state. While in this state, the port disallows all ingress and egress traffic except for 802.1X protocol packets. When a client is successfully authenticated, the port transitions to the authorized state, allowing all traffic for the client to flow normally.

If a non-802.1X capable client is connected to an unauthorized 802.1X port, the switch requests the client's identity. In this situation, the client does not respond to the request, the port remains in the unauthorized state, and the client is not granted access to the network. If a guest VLAN is configured on a port that connects to a client that does not support 802.1X, the port is placed in the configured guest VLAN and in the authorized state. For more information, see the "Using 802.1X for Guest VLANs" section.

In contrast, when an 802.1X-enabled client connects to a port that is not running the 802.1X protocol, the client initiates the authentication process by sending the EAPOL-start frame. When no response is received, the client sends the request a fixed number of times. Because no response is received, the client begins sending frames as if the port is in the authorized state.

You can control the port authorization state with the authentication port-control interface configuration command (dot1x port-control auto command in Cisco IOS Release 12.2(46)SG and earlier releases) and these keywords:

•force-authorized—Disables 802.1X authentication and causes the port to transition to the authorized state without requiring authentication exchange. The port transmits and receives normal traffic without 802.1X-based authentication of the client. This setting is the default.

•force-unauthorized—Causes the port to remain in the unauthorized state, ignoring all attempts by the client to authenticate. The switch cannot provide authentication services to the client through the interface.

•auto—Enables 802.1X authentication and causes the port to begin in the unauthorized state, allowing only EAPOL frames to be sent and received through the port. The authentication process begins when the link state of the port transitions from down to up or when an EAPOL-start frame is received. The switch requests the identity of the client and begins relaying authentication messages between the client and the authentication server. The switch can uniquely identify each client attempting to access the network by the client's MAC address.

If the client is successfully authenticated (receives an Accept frame from the authentication server), the port state changes to authorized, and all frames from the authenticated client are allowed through the port. If authentication fails, the port remains in the unauthorized state, but authentication can be retried. If the authentication server cannot be reached, the switch can retransmit the request. If no response is received from the server after the specified number of attempts, authentication fails and network access is not granted.

If the link state of a port transitions from up to down, or if an EAPOL-logoff frame is received by the port, the port returns to the unauthorized state.

Figure 40-3 shows the authentication process.

If Multidomain Authentication (MDA) is enabled on a port, this flow can be used with some exceptions that are applicable to voice authorization. For more information on MDA, see the
"Using Multiple Domain Authentication and Multiple Authentication" section.

Figure 40-3 Authentication Flowchart

802.1X Host Mode

The 802.1X port's host mode determines whether more than one client can be authenticated on the port and how authentication is enforced. You can configure an 802.1X port to use any of the five host modes described in the following sections. In addition, each mode may be modified to allow pre-authentication open access:

•Single-Host Mode

•Multiple-Hosts Mode

•Multidomain Authentication Mode

•Multiauthentication Mode

•Pre-Authentication Open Access

Single-Host Mode

You can configure an 802.1X port for single-host or multiple-hosts mode. In single-host mode (see Figure 40-1), only one client can be connected to the 802.1X-enabled switch port. The switch detects the client by sending an EAPOL frame when the port link state changes to the up state. If a client leaves or is replaced with another client, the switch changes the port link state to down, and the port returns to the unauthorized state.

Multiple-Hosts Mode

In multiple-hosts mode, you can attach multiple hosts to a single 802.1X-enabled port. Figure 40-4 shows 802.1X port-based authentication in a wireless LAN. In this mode, only one of the attached clients must be authorized for all clients to be granted network access. If the port becomes unauthorized (re-authentication fails or an EAPOL-logoff message is received), the switch denies network access to all of the attached clients. In this topology, the wireless access point is responsible for authenticating the clients attached to it, and it also acts as a client to the switch.

With multiple-hosts mode enabled, you can use 802.1X authentication to authenticate the port and port security to manage network access for all MAC addresses, including that of the client.

Figure 40-4 Multiple Host Mode Example

Multidomain Authentication Mode

Cisco IOS Release 12.2(37)SG and later releases support Multidomain Authentication (MDA), which allows an IP phone (Cisco or third-party) and a single host behind the IP phone to authenticate independently, using 802.1X, MAC authentication bypass (MAB) or (for the host only) web-based authentication. In this application, multidomain refers to two domains — data and voice — and only two MAC addresses are allowed per port. A switch can place the host in the data VLAN and the IP phone in the voice VLAN, even though they appear on the same switch port. The data VLAN and the voice VLAN can be specified in the CLI configuration. The devices are identified as either data or voice depending on the vendor-specific-atributes (VSAs) received from the authentication, authorization, and accounting (AAA) server. The data and voice VLANs can also be obtained from the VSAs received from the (AAA) server during authentication.

Figure 40-5 Multidomain Authentication Mode Example

Figure 40-5 shows a typical MDA application with a single host behind an IP phone connected to the 802.1X-enabled port. Because the client is not directly connected to the switch, the switch cannot detect a loss of port link if the client is disconnected. To prevent another device from using the established authentication of the disconnected client later, Cisco IP phones send a Cisco Discovery Protocol (CDP) host presence type length value (TLV) to notify the switch of changes in the attached client's port link state.

For details on how to configure MDA, see the "Using Multiple Domain Authentication and Multiple Authentication" section.

Multiauthentication Mode

Available starting in Cisco IOS Release 12.2(50)SG, multiauthentication mode allows one client on the voice VLAN and multiple authenticated clients on the data VLAN. When a hub or access point is connected to an 802.1X port, multiauthentication mode provides enhanced security over multiple-hosts mode by requiring authentication of each connected client. For non-802.1X devices, you can use MAB or web-based authentication as the fallback method for individual host authentications, allowing you to authenticate different hosts through different methods on a single port.

Multiauthentication also supports MDA functionality on the voice VLAN by assigning authenticated devices to either a data or voice VLAN depending on the VSAs received from the authentication server.

Note When a port is in multiauthentication mode, all VLAN assignment features including RADIUS server supplied VLAN assignment, Guest VLAN, Inaccessible Authentication Bypass, and Authentication Failed VLAN will not activate for data devices. However, RADIUS server supplied VLAN assignment is possible for voice devices.

Pre-Authentication Open Access

Starting with Cisco IOS Release 12.2(50)SG, any of the four host modes may be additionally configured to allow a device to gain network access before authentication. This pre-authentication open access is useful in an application such as the Pre-boot eXecution Environment (PXE), where a device must access the network to download a bootable image containing an authentication client.

Enable pre-authentication open access by entering the authentication open command after host mode configuration. It acts as an extension to the configured host mode. For example, if pre-authentication open access is enabled with single-host mode, then the port allows only one MAC address. When pre-authentication open access is enabled, initial traffic on the port is restricted only by whatever other access restriction, independent of 802.1X, is configured on the port. If no access restriction other than 802.1X is configured on the port, then a client device will have full access on the configured VLAN.

802.1X Violation Mode

You can use the authentication violation interface configuration command to configure the violation mode: restrict or shutdown.

In single-host mode, a security violation is triggered when more than one device are detected on the data vlan. In multidomain authentication mode, a security violation is triggered when more than one device are detected on the data or voice VLAN.

Security violation cannot be triggered in multiple-host mode or multiauthentication mode.

When security violation occurs, the port is protected depending on the configured violation action:

Shutdown—Errdisables the port; the default behavior on a port.

Restrict—The port state is unaffected. However the platform is notified to restrict the traffic from offending MAC-address.

For more information see the "Configuring Violation Action" section".

Using 802.1X with VLAN Assignment

You can use the VLAN assignment to limit network access for certain users. With the VLAN assignment, 802.1X-authenticated ports are assigned to a VLAN based on the username of the client connected to that port. The RADIUS server database maintains the username-to-VLAN mappings. After successful 802.1X authentication of the port, the RADIUS server sends the VLAN assignment to the switch. The VLAN can be a standard VLAN or a private VLAN (PVLAN).

On platforms that support PVLANs, you can isolate hosts by assigning ports into PVLANs.

When configured on the switch and the RADIUS server, 802.1X with VLAN assignment has these characteristics:

•If no VLAN is supplied by the RADIUS server, the port is configured in its access VLAN or isolated PVLAN when authentication succeeds.

•If the authentication server provides invalid VLAN information, the port remains unauthorized. This situation prevents ports from appearing unexpectedly in an inappropriate VLAN due to a configuration error.

•If the multiauthentication mode is enabled on an 802.1X port, the VLAN assignment is ignored for data devices. VLAN assignment is possible for voice device even if the port is configured in multiauthentication mode.

•If the authentication server provides valid VLAN information, the port is authorized and placed in the specified VLAN when authentication succeeds.

•If the multiple-hosts mode is enabled, all hosts are in the same VLAN as the first authenticated user.

•If 802.1X is disabled on the port, the port is returned to the configured access VLAN.

•A port must be configured as an access port (which can be assigned only into "regular" VLANs), or as a PVLAN host port (which can be assigned only into PVLANs). Configuring a port as a PVLAN host port implies that all hosts on the port are assigned into PVLANs, whether their posture is compliant or non-compliant. If the type of the VLAN named in the Access-Accept does not match the type of VLAN expected to be assigned to the port (regular VLAN to access port, secondary PVLAN to PVLAN host port), the VLAN assignment fails.

•If a guest VLAN is configured to handle non-responsive hosts, the type of VLAN configured as the guest VLAN must match the port type (that is, guest VLANs configured on access ports must be standard VLANs, and guest VLANs configured on PVLAN host ports must be PVLANs). If the guest VLAN's type does not match the port type, non-responsive hosts are treated as if no guest VLAN is configured (that is, they are denied network access).

•To assign a port into a PVLAN, the named VLAN must be a secondary PVLAN. The switch determines the implied primary VLAN from the locally configured secondary-primary association.

Note If you change the access VLAN or PVLAN host VLAN mapping on a port that is already authorized in a RADIUS assigned VLAN, the port remains in the RADIUS assigned VLAN.

To configure VLAN assignment you need to perform these tasks:

•Enable AAA authorization with the network keyword to allow interface configuration from the RADIUS server. For an illustration of how to apply the aaa authorization network group radius command, refer to the section "Enabling 802.1X Authentication" on page 24.

•Enable 802.1X. (The VLAN assignment feature is automatically enabled when you configure 802.1X on an access port.)

•Assign vendor-specific tunnel attributes in the RADIUS server. To ensure proper VLAN assignment, the RADIUS server must return these attributes to the switch:

–Tunnel-Type = VLAN

–Tunnel-Medium-Type = 802

–Tunnel-Private-Group-ID = VLAN NAME

Using 802.1X for Guest VLANs

You can use guest VLANs to enable non-802.1X-capable hosts to access networks that use 802.1X authentication. For example, you can use guest VLANs while you are upgrading your system to support 802.1X authentication.

Guest VLANs are supported on a per-port basis, and you can use any VLAN as a guest VLAN as long as its type matches the type of the port. If a port is already forwarding on the guest VLAN and you enable 802.1X support on the network interface of the host, the port is immediately moved out of the guest VLAN and the authenticator waits for authentication to occur.

Enabling 802.1X authentication on a port starts the 802.1X protocol. If the host fails to respond to packets from the authenticator within a certain amount of time, the authenticator brings the port up in the configured guest VLAN.

If the port is configured as a PVLAN host port, the guest VLAN must be a secondary PVLAN. If the port is configured as an access port, the guest VLAN must be a regular VLAN. If the guest VLAN configured on a port is not appropriate for the type of the port, the switch behaves as if no guest VLAN is configured (that is, non-responsive hosts are denied network access).

For details on how to configure guest VLANs, see the "Configuring 802.1X with Guest VLANs" section.

Usage Guidelines for Using 802.1X Authentication with Guest VLANs

The usage guidelines for using 802.1X authentication with guest VLANs are as follows:

•When you reconfigure a guest VLAN to a different VLAN, any authentication failed ports are also moved and the ports stay in their current authorized state.

•When you shut down or remove a guest VLAN from the VLAN database, any authentication failed ports are immediately moved to an unauthorized state and the authentication process is restarted.

Note No periodic reauthentication is allowed with guest VLANs.

Usage Guidelines for Using 802.1X Authentication with Guest VLANs on Windows-XP Hosts

The usage guidelines for using 802.1X authentication with guest VLANs on Windows-XP hosts are as follows:

•If the host fails to respond to the authenticator, the port attempts to connect three times (with a 30 second timeout between each attempt). After this time, the login/password window does not appear on the host, so you must unplug and reconnect the network interface cable.

•Hosts responding with an incorrect login/password fail authentication. Hosts failing authentication are not put in the guest VLAN. The first time that a host fails authentication, the quiet-period timer starts, and no activity occurs for the duration of the quiet-period timer. When the quiet-period timer expires, the host is presented with the login/password window. If the host fails authentication for the second time, the quiet-period timer starts again, and no activity occurs for the duration of the quiet-period timer. The host is presented with the login/password window a third time. If the host fails authentication the third time, the port is placed in the unauthorized state, and you must disconnect and reconnect the network interface cable.

Using 802.1X with MAC Authentication Bypass

The 802.1X protocol has 3 entities: client (supplicant), authenticator, and authentication server. Typically, the host PC runs the supplicant software and tries to authenticate itself by sending its credentials to the authenticator which in turn relays that info to the authentication server for authentication.

However, not all hosts may have supplicant functionality. Devices that cannot authenticate themselves using 802.1X but still need network access can use MAC Authentication Bypass (MAB), which uses the connecting device's MAC address to grant or deny network access.

Typically, you would use this feature on ports where devices such as printers are connected. Such devices do not have 802.1X supplicant functionality.

In a typical deployment, the RADIUS server maintains a database of MAC addresses that require access. When this feature detects a new MAC address on a port, it generates a RADIUS request with both username and password as the device's MAC address. After authorization succeeds, the port is accessible to the particular device through the same code path that 802.1X authentication would take when processing an 802.1X supplicant. If authentication fails, the port moves to the guest VLAN if configured, or it remains unauthorized.

The Catalyst 4500 series switch also supports re-authentication of MACs on a per port level. Be aware that the re-authentication functionality is provided by 802.1X and is not MAB specific. In the re-authentication mode, a port stays in the previous RADIUS-sent VLAN and tries to re-authenticate itself. If the re-authentication succeeds, the port stays in the RADIUS-sent VLAN. Otherwise, the port becomes unauthorized and moves to the guest VLAN if one is configured.

For details on how to configure MAB, see the "Configuring 802.1X with MAC Authentication Bypass" section.

Feature Interaction

This section lists feature interactions and restrictions when MAB is enabled. If a feature is not listed, assume that it interacts seamlessly with MAB (such as Unidirectional Controlled Port).

•MAB can only be enabled if 802.1X is configured on a port. MAB functions as a fall back mechanism for authorizing MACs. If you configure both MAB and 802.1X on a port, the port attempts to authenticate using 802.1X. If the host fails to respond to EAPOL requests and MAB is configured, the 802.1X port is opened up to listen to packets and to grab a MAC address, rather than attempt to authenticate endlessly.

Based on the default 802.1X timer values, the transition between mechanisms takes approximately 90 seconds. You can shorten the time by reducing the value of the transmission period time, which affects the frequency of EAPOL transmission. A smaller timer value results in EAPOLs sent during a shorter period of time. With MAB enabled, after 802.1X performs one full set of EAPOLs, the learned MAC address is forwarded to the authentication server for processing.

The MAB module performs authorization for the first MAC address detected on the wire. The port is considered authorized once a valid MAC address is received that RADIUS approves of.

802.1X authentication can re-start if an EAPOL packet is received on a port that was initially authorized as a result of MAB.

Figure 40-6 shows the message exchange during MAB.

Figure 40-6 Message Exchange during MAC Authentication Bypass

•The authentication-failed VLAN is used only with dot1x-authentication-failed users. MAB is not attempted with dot1x-authentication-failed users. If 802.1X authentication fails, a port moves to the authentication-failed VLAN (if configured) whether MAB is configured or not.

•When both MAB and guest VLAN are configured and no EAPOL packets are received on a port, the 802.1X state-machine is moved to a MAB state where it opens the port to listen to traffic and grab MAC addresses. The port remains in this state forever waiting to see a MAC on the port. A detected MAC address that fails authorization causes the port to be moved to the guest VLAN if configured.

While in a guest VLAN, a port is open to all traffic on the specified guest VLAN. Therefore, non-802.1X supplicants that normally would be authorized but are in guest VLAN due to the earlier detection of a device that failed authorization, would remain in the guest VLAN indefinitely. However, loss of link or the detection of an EAPOL on the wire causes a transition out of the guest VLAN and back to the default 802.1X mode.

•Once a new MAC has been authenticated by MAB, the responsibility to limit access falls upon the 802.1X Authenticator (or port security) to secure the port. The 802.1X default host parameter is defined only for a single host. If the port is changed to multi-user host, port security must be employed to enforce the number of MAC addresses allowed thru this port.

•Catalyst 4500 series switch supports MAB with VVID, with the restriction that the MAC address appears on a port data VLAN only. All IP phone MACs learned via CDP are allowed on voice VLANs.

•MAB and VMPS are mutually exclusive because their functionality overlaps.

Using 802.1X with Web-Based Authentication

The web-based authentication feature, known as Web Authentication Proxy, enables you to authenticate end users on host systems that do not run the IEEE 802.1X supplicant.

When configuring web-based authentication, note the following guidelines:

•Fallback to web-based authentication is configured on switch ports in access mode. Ports in trunk mode are not supported.

•Fallback to web-based authentication is not supported on EtherChannels or EtherChannel members.

•Although fallback to web-based authentication is an interface-specific configuration, the web-based authentication fallback behavior is defined in a global fallback profile. If the global fallback configuration changes, the new profile is not used until the next instance of authentication fallback.

For detailed information on configuring web-based authentication, see Chapter 42 "Configuring Web-Based Authentication."

Using 802.1X with Inaccessible Authentication Bypass

When a switch cannot reach the configured RADIUS servers and clients (supplicants) cannot be authenticated, you can configure a switch to allow network access to hosts connected to critical ports that are enabled for Inaccessible Authentication Bypass.

When this feature is enabled, a switch monitors the status of the configured RADIUS servers. If no RADIUS servers are available, ports with Inaccessible Authentication Bypass enabled are authorized. You can specify a Inaccessible Authentication Bypass VLAN on a per-port basis.

Ports that were already authorized when RADIUS becomes unavailable are unaffected by Inaccessible Authentication Bypass.

When RADIUS becomes available, critically-authorized ports may be configured to automatically reauthenticate themselves.

For details on how to configure Inaccessible Authentication Bypass, see the "Configuring 802.1X with Inaccessible Authentication Bypass" section.

Using 802.1X with Unidirectional Controlled Port

Unidirectional Controlled Port is a combined hardware/software feature that allows dormant PCs to be "powered on" based on the receipt of a specific Ethernet frame, known as the magic packet. Generally, Unidirectional Controlled Port is used in environments where administrators plan to manage remote systems during off-hours, when it's likely that the systems have been powered down.

Use of Unidirectional Controlled Port with hosts attached through 802.1X ports presents a unique problem; when the host powers down, a 802.1X port becomes unauthorized. In this state, the port allows the receipt and transmission of EAPoL packets only. Therefore, the Unidirectional Controlled Port magic packet cannot reach the host; without powering up, the PC cannot authenticate and open the port.

Unidirectional Controlled Port solves this problem by allowing packets to be transmitted on unauthorized 802.1X ports.

Note Unidirectional Controlled Port only works when Spanning Tree Portfast is enabled on the port.

For details on how to configure 802.1X with Unidirectional Controlled Port, see the "Configuring 802.1X with Unidirectional Controlled Port" section

Unidirectional State

A unidirectional controlled port is typically configured when a connected host might enter a sleeping mode or power-down state. When either occurs, the host does not exchange traffic with other devices in the network. A host connected to the unidirectional port cannot send traffic to the network; it can only receive traffic from other devices in the network.

When you configure a port as unidirectional (with the authentication control-direction in interface configuration command), the port will receive traffic in VLANs on that port, but it is not put into a spanning-tree forwarding state. If a VLAN contains only unauthenticated ports, any SVI on that VLAN will be in a down state, during which packets will not be routed into the VLAN. For the SVI to be up, and so enable packets to be routed into the VLAN, at least one port in the VLAN must either be authenticated or in the spanning-tree forwarding state.

Bidirectional State

When you configure a port as bidirectional with the authentication control-direction both interface configuration command (or the dot1x control-direction both interface configuration command for Cisco IOS Release 12.2(46) or earlier), the port is access-controlled in both directions. In this state, except for EAPOL packets, a switch port does not receive or send packets.

Using 802.1X with Authentication Failed VLAN Assignment

You can use authentication-failed VLAN assignment on a per-port basis to provide access for authentication failed users. Authentication failed users are end hosts that are 802.1X- capable but do not have valid credentials in an authentication server or end hosts that do not give any username and password combination in the authentication pop-up window on the user side.

If a user fails the authentication process, that port is placed in the authentication-failed VLAN. The port remains in the authentication-failed VLAN until the reauthentication timer expires. When the reauthentication timer expires the switch starts sending the port re-authentication requests. If the port fails reauthentication it remains in the authentication-failed VLAN. If the port is successfully reauthenticated, the port is moved either to the VLAN sent by RADIUS server or to the newly authenticated ports configured VLAN; the location depends on whether RADIUS is configured to send VLAN information.

Note When enabling periodic reauthentication (see the "Enabling Periodic Reauthentication" section), only local reauthentication timer values are allowed. You cannot use a RADIUS server to assign the reauthentication timer value.

You can set the maximum number of authentication attempts that the authenticator sends before moving a port into the authentication-failed VLAN. The authenticator keeps a count of the failed authentication attempts for each port. A failed authentication attempt is either an empty response or an EAP failure. The authenticator tracks any mix of failed authentication attempts towards the authentication attempt count. After the maximum number of attempts is reached the port is placed in the authentication-failed VLAN until the reauthentication timer expires again.

Note RADIUS may send a response without an EAP packet in it when it does not support EAP, and sometimes third party RADIUS servers also send empty responses. When this happens, the authentication attempt counter is incremented.

For details on how to configure Authentication Failed VLAN Assignment, see the "Configuring 802.1X with Authentication Failed" section.

Usage Guidelines for Using Authentication Failed VLAN Assignment

•You should enable reauthentication. The ports in authentication-failed VLANs do not receive reauthentication attempts if reauthentication is disabled. In order to start the reauthentication process the authentication-failed VLAN must receive a link down event or an EAP logoff event from the port. If the host is behind a hub, you may never get a link down event and may not detect the new host until the next reauthentication occurs. Therefore, it is recommended to have re-authentication enabled in that case.

•EAP failure messages are not sent to the user. If the user failures authentication the port is moved to an authentication-failed VLAN and a EAP success message is sent to the user. Because the user is not notified of the authentication failure there may be confusion as to why there is restricted access to the network. A EAP Success message is sent for the following reasons:

–If the EAP Success message is not sent, the user tries to authenticate every 60 seconds (by default) by sending an EAP-start message.

–In some cases, users have configured DHCP to EAP-Success and unless the user sees a success, DHCP does not work on the port.

•Sometimes a user caches an incorrect username and password combination after receiving a EAP success message from the authenticator and reuses that information in every re-authentication. Until the user passes the correct username and password combination the port remains in the authentication-failed VLAN.

•When an authentication failed port is moved to an unauthorized state the authentication process is restarted. If you should fail the authentication process again the authenticator waits in the held state. After you have correctly reauthenticated all 802.1X ports are reinitialized and treated as normal 802.1X ports.

•When you reconfigure an authentication-failed VLAN to a different VLAN, any authentication failed ports are also moved and the ports stay in their current authorized state.

•When you shut down or remove an authentication-failed VLAN from the VLAN database, any authentication failed ports are immediately moved to an unauthorized state and the authentication process is restarted. The authenticator does not wait in a held state because the authentication-failed VLAN configuration still exists. While the authentication-failed VLAN is inactive, all authentication attempts are counted, and as soon as the VLAN becomes active the port is placed in the authentication-failed VLAN.

•If you reconfigure the maximum number of authentication failures allowed by the VLAN, the change takes affect after the reauthentication timer expires.

•Internal VLANs that are used for Layer 3 ports cannot be configured as authentication-failed VLANs.

•The authentication-failed VLAN is supported only in single-host mode (the default port mode).

•When a port is placed in an authentication-failed VLAN the user's MAC address is added to the mac-address-table. If a new MAC address appears on the port, it is treated as a security violation.

•When an authentication failed port is moved to an authentication-failed VLAN, the Catalyst 4500 series switch does not transmit a RADIUS-Account Start Message like it does for regular 802.1X authentication.

Using 802.1X with Port Security

You can enable port security on an 802.1X port in either single- or multiple-host mode. (To do so, you must configure port security with the switchport port-security interface configuration command.) When you enable port security and 802.1X on a port, 802.1X authenticates the port, and port security manages the number of MAC addresses allowed on that port, including that of the client. Hence, you can use an 802.1X port with port security enabled to limit the number or group of clients that can access the network.

For information on selecting multi-host mode, see the "Resetting the 802.1X Configuration to the Default Values" section.

These examples describe the interaction between 802.1X and port security on a switch:

•When a client is authenticated, and the port security table is not full, the client's MAC address is added to the port security list of secure hosts. The port then proceeds to come up normally.

When a client is authenticated and manually configured for port security, it is guaranteed an entry in the secure host table (unless port security static aging has been enabled).

A security violation occurs if an additional host is learned on the port. The action taken depends on which feature (802.1X or port security) detects the security violation:

–If 802.1X detects the violation, the action is to err-disable the port.

–If port security detects the violation, the action is to shutdown or restrict the port (the action is configurable).

The following describes when port security and 802.1X security violations occur:

–In single host mode, after the port is authorized, any MAC address received other than the client's causes a 802.1X security violation.

–In single host mode, if installation of an 802.1X client's MAC address fails because port security has already reached its limit (due to a configured secure MAC addresses), a port security violation is triggered.

–In multi host mode, once the port is authorized, any additional MAC addresses that cannot be installed because the port security has reached its limit triggers a port security violation.

•When an 802.1X client logs off, the port transitions back to an unauthenticated state, and all dynamic entries in the secure host table are cleared, including the entry for the client. Normal authentication then ensues.

•If you administratively shut down the port, the port becomes unauthenticated, and all dynamic entries are removed from the secure host table.

•Only 802.1X can remove the client's MAC address from the port security table. Note that in multi host mode, with the exception of the client's MAC address, all MAC addresses that are learned by port security can be deleted using port security CLIs.

•Whenever port security ages out a 802.1X client's MAC address, 802.1X attempts to reauthenticate the client. Only if the reauthentication succeeds is the client's MAC address be retained in the port security table.

•All of the 802.1X client's MAC addresses are tagged with (dot1x) when you display the port security table by using CLI.

Using 802.1X Authentication with ACL Assignments and Redirect URLs

Starting with Cisco IOS Release 12.2(50)SG, you can download per-host policies such as ACLs and redirect URLs to the switch from the RADIUS server during 802.1X or MAB authentication of the host. ACL download is also supported with web authentication after a fallback from 802.1X or MAB.

When the 802.1X host mode of the port is either single-host, MDA, or multiauthentication, the downloaded ACLs (DACLs) are modified to use the authenticated host's IP address as the source address. When the host mode is multiple-hosts, the source address is configured as ANY, and the downloaded ACLs or redirects apply to all devices on the port.

If no ACLs are provided during the authentication of a host, the static default ACL configured on the port is applied to the host. On a voice VLAN port, only the static default ACL of the port is applied to the phone.

Topics include:

•Cisco Secure ACS and AV Pairs for URL-Redirect

•ACLs

For details on how to configure downloadable ACL and URL redirect, refer to the "Configuring 802.1X Authentication with ACL Assignments and Redirect URLs" section.

Cisco Secure ACS and AV Pairs for URL-Redirect

When downloadable ACL is enabled, Cisco Secure ACS provides AAA services through RADIUS.

You can set these Attribute-Value (AV) pairs on the Cisco Secure ACS with RADIUS cisco-av-pair vendor-specific attributes (VSAs).

CiscoSecure-Defined-ACL specifies the names of the DACLs on the Cisco Secure ACS. The switch receives the ACL name through the CiscoSecure-Defined-ACL AV pair in the format: #ACL#-IP-name-number

name is the ACL name. number is the version number (like 3f783768).

The Auth-Manager code verifies whether the access control entries (ACEs) of the specified downloadable ACL were previously downloaded. If not, the Auth-Manager code sends an AAA request with the downloadable ACL name as the username so that the ACEs are downloaded. The downloadable ACL is then created as a named ACL on the switch. This ACL has ACEs with a source address of any and does not have an implicit deny statement at the end. When the downloadable ACL is applied to an interface after authentication completes, the source address changes from any to the host source IP address depending on the host mode of the interface. The ACEs are prepended to the downloadable ACL applied to the switch interface to which the endpoint device is connected. If traffic matches the CiscoSecure-Defined-ACL ACEs, the appropriate actions are taken.

url-redirect and url-redirect-acl specify the local URL policy on the switch. The switches use these cisco-av-pair VSAs as follows:

–url-redirect = <HTTP or HTTPS URL>

–url-redirect-acl = switch ACL name or number

These AV pairs enable the switch to intercept an HTTP or HTTPS request from the endpoint device and forward the client web browser to the specified redirect address from which the latest antivirus files can be downloaded. The url-redirect AV pair on the Cisco Secure ACS contains the URL to which the web browser is redirected. The url-redirect-acl AV pair contains the name or number of an ACL that specifies the HTTP or HTTPS traffic to be redirected. Traffic that matches a permit entry in the redirect ACL is redirected.

Note The redirect or default ACL must be defined on the switch.

ACLs

If downloadable ACL is configured for a particular client on the authentication server, you must configure a default port ACL on a client-facing switch port.

If the default ACL is configured on the switch and the Cisco Secure ACS sends a host access policy to the switch, it applies the policy to traffic from the host connected to a switch port. If the policy does not apply, the switch applies the default ACL. If the Cisco Secure ACS sends the switch a downloadable ACL, this ACL takes precedence over the default ACL already configured on the switch port. However, if the switch receives a host access policy from the Cisco Secure ACS, but the default ACL is not configured, the authorization failure is declared.

For details on how to configure a downloadable policy, refer to the "Configuring a Downloadable Policy" section.

Using 802.1X with RADIUS-Provided Session Timeouts

You can specify whether a switch uses a locally configured or a RADIUS-provided reauthentication timeout. If the switch is configured to use the local timeout, it reauthenticates the host when the timer expires.

If the switch is configured to use the RADIUS-provided timeout, it scans the RADIUS Access-Accept message for the Session-Timeout and optional Termination-Action attributes. The switch uses the value of the Session-Timeout attribute to determine the duration of the session, and it uses the value of the Termination-Action attribute to determine the switch action when the session's timer expires.

If the Termination-Action attribute is present and its value is RADIUS-Request, the switch reauthenticates the host. If the Termination-Action attribute is not present, or its value is Default, the switch terminates the session.

Note The supplicant on the port detects that its session has been terminated and attempts to initiate a new session. Unless the authentication server treats this new session differently, the client may see only a brief interruption in network connectivity as the switch sets up a new session.

If the switch is configured to use the RADIUS-supplied timeout, but the Access-Accept message does not include a Session-Timeout attribute, the switch never reauthenticates the supplicant. This behavior is consistent with Cisco's wireless access points.

For details on how to configure RADIUS-provided session timeouts, see the "Configuring RADIUS-Provided Session Timeouts" section.

Using 802.1X with Voice VLAN Ports

A voice VLAN port is a special access port associated with two VLAN identifiers:

•Voice VLAN ID (VVID) to carry voice traffic to and from the IP phone. The VVID is used to configure the IP phone connected to the port.

•Port VLAN ID (PVID) to carry the data traffic to and from the workstation connected to the switch through the IP phone. The PVID is the native VLAN of the port.

Each port that you configure for a voice VLAN is associated with a VVID and a PVID. This configuration allows voice traffic and data traffic to be separated onto different VLANs.

A voice VLAN port becomes active when a link exists whether the port is AUTHORIZED or UNAUTHORIZED. All traffic exiting the voice VLAN is obtained correctly and appears in the MAC address table. Cisco IP phones do not relay CDP messages from other devices. So, if several Cisco IP phones are connected in a series, the switch recognizes only the one directly connected to it. When 802.1X is enabled on a voice VLAN port, the switch drops packets from unrecognized Cisco IP phones more than one hop away.

When 802.1X is enabled on a port, you cannot configure a PVID that is equal to a VVID. For more information about voice VLANs, see Chapter 38 "Configuring Voice Interfaces."

Observe the following feature interactions:

•802.1X VLAN assignment cannot assign to the port the same VLAN as the voice VLAN; otherwise, the 802.1X authentication fails. The same holds true for dynamic VLAN assignment.

•802.1X guest VLAN works with the 802.1X voice VLAN port feature. However, the guest VLAN cannot be the same as the voice VLAN.

•802.1X port security works with the 802.1X voice VLAN port feature and is configured per port. Two MAC addresses must be configured: one for the Cisco IP phone MAC address on the VVID and one for the PC MAC address on PVID.

However, you cannot use the 802.1X voice VLAN port feature with 802.1X port security's sticky MAC address configuration and statically configured MAC address configuration.

•802.1X accounting is unaffected by the 802.1X voice VLAN port feature.

•When 802.1X is configured on a port, you cannot connect multiple IP phones to a
Catalyst 4500 series switch through a hub.

•Because voice VLANs cannot be configured as PVLAN host ports, and because only PVLANs can be assigned to PVLAN host ports, VLAN assignment cannot assign a PVLAN to a port with a voice VLAN configured.

For details on how to configure 802.1X with voice VLANs, see the "Configuring 802.1X with Voice VLAN" section.

Using Multiple Domain Authentication and Multiple Authentication

Multiple Domain Authentication (MDA) allows both a data device and a voice device, such as an IP phone (Cisco or 3rd party non-Cisco), to authenticate on the same switch port, which is divided into a data domain and a voice domain.

Multiple Authentication allows multiple data devices and a voice device. When a voice VLAN is configured on a multi-authentication port, the port can perform authentication in the voice domain as on an MDA port.

MDA does not enforce the order of device authentication. For best results, however, you should authenticate a voice device before you authenticate a data device on an MDA-enabled port.

Observe the following guidelines for configuring MDA:

Note The same guidelines also apply for Multiple Authentication when voice VLAN is configured.

•It is highly recommended that you enable CoPP on an MDA-enabled port to protect against a DoS attack. Refer to Chapter 44 "Configuring Control Plane Policing."

•To configure a switch port for MDA or Multiple Authentication, see the "Configuring Multiple Domain Authentication and Multiple Authorization" section.

•You must configure the voice VLAN for the IP phone when the host mode is set to multidomain. For more information, see Chapter 38 "Configuring Voice Interfaces."

•To authorize a voice device, the AAA server must be configured to send a Cisco Attribute-Value (AV) pair attribute with a value of device-traffic-class=voice. Without this value, the switch treats the voice device as a data device.

•The guest VLAN and restricted VLAN features only apply to the data devices on an MDA-enabled port. The switch treats a voice device that fails authorization as a data device.

•If more than one device attempts authorization on either the voice or the data domain of a port, it is error disabled.

•Until a device is authorized, the port drops its traffic. Non-Cisco IP phones or voice devices are allowed into both the data and voice VLANs. The data VLAN allows the voice device to contact a DHCP server to obtain an IP address and acquire the voice VLAN information. After the voice device starts sending on the voice VLAN, its access to the data VLAN is blocked. A security violation may occur in MDA if the voice device continues to send traffic on the data VLAN.

•MDA can use MAC authentication bypass as a fallback mechanism to allow the switch port to connect to devices that do not support 802.1X authentication. This is especially useful for 3rd-party phones without 802.1X supplicant. For more information, see the "Using 802.1X with MAC Authentication Bypass" section.

•When a data or a voice device is detected on a port, its MAC address is blocked until authorization succeeds. If the authorization fails, the MAC address remains blocked for 5 minutes.

•If more than one device is detected on the data VLAN or more than one voice device is detected on the voice VLAN while a port is unauthorized, the port is error disabled.

•When a port host mode is changed from single- or multihost to multidomain mode, an authorized data device remains authorized on the port. However, a Cisco IP phone that has been allowed on the port in the voice VLAN is automatically removed and must be reauthenticated on that port.

•Active fallback mechanisms such as guest VLAN and restricted VLAN remain configured after a port changes from single- or multihost mode to multidomain mode.

•Switching a port host mode from multidomain to single- or multihost mode removes all authorized devices from the port.

•If a data domain is authorized first and placed in the guest VLAN, non-802.1X-capable voice devices need to tag their packets on the voice VLAN to trigger authentication.

•We do not recommend per-user ACLs with an MDA-enabled port. An authorized device with a per-user ACL policy might impact traffic on both the voice and data VLANs of the port. If used, only one device on the port should enforce per-user ACLs.

How 802.1X Fails on a Port

802.1X may fail on a port in three ways: timeout, explicit failure, and protocol timeout.

Timeout—A switch attempts 802.1X at link up but the attached endpoint is not 802.1X-capable. After the configured number of retries and timeouts, the switch attempts the next authentication method if one is configured (like MAB). If MAB fails, the switch deploys the Guest VLAN (also called the no-response VLAN), if configured. The Guest VLAN is configured with the authentication event no-response interface command.

Explicit Failure—A switch and the endpoint perform the entire 802.1X authentication sequence and the result is an explicit failure (usually indicated by an Access-Reject from the RADIUS server to the switch and an EAP-Failure sent from the switch to the endpoint). In this case, the switch attempts MAB (if "authentication event failure action next-method" is configured) or deploy the AuthFail VLAN (if "authentication event failure action authorize vlan" is configured).

Protocol Timeout—A switch and the endpoint start the 802.1X authentication process but do not complete it. For example, the endpoint may send an 802.1X EAPoL-Start message and then stop responding to the switch (perhaps, because the endpoint lacks a credential or because it is waiting for end user to enter some information). In this case, the switch knows that the connected device is EAPoL-capable, so it will not deploy the Guest VLAN after timing out. Instead, it restarts authentication after a timeout. The switch continues to label the port as EAPoL-capable until a physical link down event is detected. To force the switch to deploy the Guest VLAN in the case of a protocol timeout, configure dot1x guest-vlan supplicant globally. If the port is configured for hostmode multi-domain authentication, the switch behaves as if dot1x guest-vlan supplicant is configured.

Supported Topologies

The 802.1X port-based authentication supports two topologies:

•Point-to-point

•Wireless LAN

In a point-to-point configuration (see Figure 40-1), only one client can be connected to the 802.1X-enabled switch port when the multi-host mode is not enabled (the default). The switch detects the client when the port link state changes to the up state. If a client leaves or is replaced with another client, the switch changes the port link state to down, and the port returns to the unauthorized state.

For 802.1X port-based authentication in a wireless LAN (Figure 40-7), you must configure the 802.1X port as a multiple-host port that is authorized as a wireless access point once the client is authenticated. (See the "Resetting the 802.1X Configuration to the Default Values" section.) When the port is authorized, all other hosts that are indirectly attached to the port are granted access to the network. If the port becomes unauthorized (reauthentication fails or an EAPOL-logoff message is received), the switch denies access to the network for all wireless access point-attached clients. In this topology, the wireless access point is responsible for authenticating clients attached to it, and the wireless access point acts as a client to the switch.

Figure 40-7 Wireless LAN Example

Configuring 802.1X Port-Based Authentication

To configure 802.1X, follow this procedure:

Step 1 Enable 802.1X authentication. See the "Enabling 802.1X Authentication" section.

Step 2 Configure switch to RADIUS server communication. See the "Configuring Switch-to-RADIUS-Server Communication" section.

Step 3 Adjust the 802.1X timer values. See the "Changing the Quiet Period" section.

Step 4 Configure optional features. See the "Configuring RADIUS-Provided Session Timeouts" section.

These sections describe how to configure 802.1X:

•Default 802.1X Configuration

•802.1X Configuration Guidelines

•Enabling 802.1X Authentication (required)

•Configuring Switch-to-RADIUS-Server Communication (required)

•Configuring Multiple Domain Authentication and Multiple Authorization

•Configuring 802.1X Authentication with ACL Assignments and Redirect URLs

•Configuring 802.1X Authentication with Per-User ACL and Filter-ID ACL

•Configuring RADIUS-Provided Session Timeouts (optional)

•Configuring Violation Action (optional)

•Configuring 802.1X with Guest VLANs (optional)

•Configuring 802.1X with MAC Authentication Bypass (optional)

•Configuring 802.1X with Inaccessible Authentication Bypass (optional)

•Configuring 802.1X with Unidirectional Controlled Port (optional)

•Configuring 802.1X with Authentication Failed (optional)

•Configuring 802.1X with Voice VLAN (optional)

•Configuring 802.1X with VLAN Assignment

•Enabling Fallback Authentication

•Enabling Periodic Reauthentication (optional)

•Enabling Multiple Hosts (optional

•Changing the Quiet Period (optional)

•Changing the Switch-to-Client Retransmission Time (optional)

•Setting the Switch-to-Client Frame-Retransmission Number (optional)

•Manually Reauthenticating a Client Connected to a Port (optional)

•Initializing the 802.1X Authentication State

•Removing 802.1X Client Information

•Resetting the 802.1X Configuration to the Default Values (optional)

Default 802.1X Configuration

Table 40-1 shows the default 802.1X configuration.

802.1X Configuration Guidelines

This section describes the guidelines for configuring 802.1X authentication:

•The 802.1X protocol is supported only on Layer 2 static access, PVLAN host ports, and Layer 3 routed ports. You cannot configure 802.1X for any other port modes.

•If you are planning to use VLAN assignment, be aware that the features use general AAA commands. For information on how to configure AAA, refer to the "Enabling 802.1X Authentication" section. Alternatively, you can refer to the Cisco IOS security documentation:

–http://www.cisco.com/en/US/products/ps6586/products_ios_technology_home.html

Enabling 802.1X Authentication

To enable 802.1X port-based authentication, you first must enable 802.1X globally on your switch, then enable AAA and specify the authentication method list. A method list describes the sequence and authentication methods that must be queried to authenticate a user.

The software uses the first method listed in the method list to authenticate users; if that method fails to respond, the software selects the next authentication method in the list. This process continues until there is successful communication with a listed authentication method or until all defined methods are exhausted. If authentication fails at any point in this cycle, the authentication process stops, and no other authentication methods are attempted.

Note To allow VLAN assignment, you must enable AAA authorization to configure the switch for all network-related service requests.

To configure 802.1X port-based authentication, perform this task:

Switch# configure terminal

Switch(config)#  
dot1x system-auth-control

Switch(config)# aaa new-model

Switch(config)# aaa authentication 
dot1x {default} method1 [method2...]

Switch(config)# aaa authorization 
network {default} group radius

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access

Switch(config-if)# dot1x pae 
authenticator

Cisco IOS Release 12.2(50)SG and later

Switch(config-if)# authentication 
port-control auto

Cisco IOS Release 12.2(46)SG or earlier 
releases

Switch(config-if)# dot1x 
port-control auto

Switch(config-if)# end

Switch # show dot1x interface 
interface-id details

Switch# show running-config

Switch# copy running-config 
startup-config

Note Enabling Spanning Tree PortFast ensures that a port comes up immediately after authorization.

Note Whenever you configure any 802.1X parameter on a port, a dot1x authenticator is automatically created on the port. As a result dot1x pae authenticator appears in the configuration. This is to ensure that dot1x authentication still works on legacy configurations without manual intervention. This is likely to change in future releases.

This example shows how to enable 802.1X and AAA on Fast Ethernet port 2/1, and how to verify the configuration:

Cisco IOS Release 12.2(50)SG and later

Switch# configure terminal

Switch(config)# dot1x system-auth-control

Switch(config)# aaa new-model

Switch(config)# aaa authentication dot1x default group radius

Switch(config)# interface fastethernet2/1

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# authentication port-control auto

Switch(config-if)# end

Switch# show authentication sessions interface f9/2 

            Interface:  FastEthernet9/2

          MAC Address:  0007.e95d.83c4

           IP Address:  Unknown

               Status:  Running

               Domain:  UNKNOWN

       Oper host mode:  single-host

     Oper control dir:  both

      Session timeout:  N/A

         Idle timeout:  N/A

    Common Session ID:  0A050B160000009505106398

      Acct Session ID:  0x0000009B

               Handle:  0x0D000095

Runnable methods list:

       Method   State

       dot1x    Running

       mab      Not run

Cisco IOS Release 12.2(46)SG or earlier

Switch# configure terminal

Switch(config)# dot1x system-auth-control

Switch(config)# aaa new-model

Switch(config)# aaa authentication dot1x default group radius

Switch(config)# interface fastethernet2/1

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x port-control auto

Switch(config-if)# end

Switch# show dot1x interface f9/2 details 

Dot1x Info for FastEthernet9/2

-----------------------------------

PAE                       = AUTHENTICATOR

PortControl               = AUTO

ControlDirection          = Both 

HostMode                  = SINGLE_HOST

QuietPeriod               = 60

ServerTimeout             = 0

SuppTimeout               = 30

ReAuthMax                 = 2

MaxReq                    = 2

TxPeriod                  = 30

Dot1x Authenticator Client List

-------------------------------

Supplicant                = 0007.e95d.83c4

Session ID                = 0A050B160000009505106398

    Auth SM State         = AUTHENTICATING

    Auth BEND SM State    = REQUEST

Port Status               = UNAUTHORIZED

The following example illustrates when a port is authorized:

Switch# show authentication sessions  int G4/5

            Interface:  GigabitEthernet4/5

          MAC Address:  0015.e981.0531

           IP Address:  Unknown

            User-Name:  ctssxp

               Status:  Authz Success

               Domain:  DATA

       Oper host mode:  single-host

     Oper control dir:  both

      Session timeout:  N/A

         Idle timeout:  N/A

    Common Session ID:  0A053F0F00000004041E6B0C

      Acct Session ID:  0x00000021

               Handle:  0x2C000004

Runnable methods list:

       Method   State

       dot1x    Authc Success

Switch# show dot1x interface G4/5 details

Dot1x Info for GigabitEthernet4/5

-----------------------------------

PAE                       = AUTHENTICATOR

PortControl               = AUTO

ControlDirection          = Both   

HostMode                  = SINGLE_HOST

QuietPeriod               = 60

ServerTimeout             = 0

SuppTimeout               = 30

ReAuthMax                 = 2

MaxReq                    = 2

TxPeriod                  = 30

Dot1x Authenticator Client List

-------------------------------

Supplicant                = 0015.e981.0531

Session ID                = 0A053F0F00000004041E6B0C

    Auth SM State         = AUTHENTICATED

    Auth BEND SM State    = IDLE

Port Status               = AUTHORIZED

Configuring Switch-to-RADIUS-Server Communication

A RADIUS security server is identified by its host name or IP address, host name and specific UDP port number, or IP address and specific UDP port numbers. The combination of the IP address and UDP port number creates a unique identifier, which enables RADIUS requests to be sent to multiple UDP ports on a server at the same IP address. If two different host entries on the same RADIUS server are configured for the same service—for example, authentication—the second host entry configured acts as the fail-over backup to the first one. The RADIUS host entries are tried in the order they were configured.

To configure the RADIUS server parameters on the switch, perform this task:

Switch# configure terminal

Switch(config)# radius-server host 
{hostname | ip-address} auth-port 
port-number [acct-port port-number] 
[test username name] 
[ignore-auth-port] [ignore-acct-port] 
[idle-time min] key string

Switch(config-if)# radius deadtime 
min

Switch(config-if)# radius 
dead-criteria time seconds tries num

Switch(config-if)# ip radius 
source-interface m/p

Switch(config)# end

Switch# show running-config

Switch# copy running-config 
startup-config

This example shows how to specify the server with IP address 172.120.39.46 as the RADIUS server. The first command specifies port 1612 as the authorization port, sets the encryption key to rad123.

The second command dictates that key matches are performed on the RADIUS server:

Switch# configure terminal

Switch(config)# radius-server host 172.l20.39.46 auth-port 1612 key rad123

Switch(config)# ip radius source-interface g3/2

Switch(config)# end

Switch#

You can globally configure the timeout, retransmission, and encryption key values for all RADIUS servers by using the radius-server host global configuration command. If you want to configure these options on a per-server basis, use the radius-server timeout, radius-server retransmit, and the radius-server key global configuration commands.

You also need to create a AAA client setting on the RADIUS server. These settings include the IP address of the switch and the key string to be shared by both the server and the switch.

Configuring Multiple Domain Authentication and Multiple Authorization

Note Multiple Authentication requires Cisco IOS Release 12.2(50)SG and later releases.

To configure MDA and Multiple Authentication, perform this task.

Switch# configure terminal

Switch(config)# radius-server vsa 
send authentication

Switch(config)# interface 
interface-id

Cisco IOS Release 12.2(50)SG and later

Switch(config-if)# [no] 
authentication host-mode 
{single-host | multi-host | 
multi-domain} | multi-auth}

Cisco IOS Release 12.2(46)SG or earlier 
releases

Switch(config-if)# [no] dot1x 
host-mode {single-host | multi-host 
| multi-domain}

Switch(config-if)# switchport voice 
vlan vlan-id

Switch(config-if)# end

Switch# show dot1x interface 
interface-id [detail]

Switch# copy running-config 
startup-config

This example shows how to enable 802.1X authentication and to allow multiple hosts:

Cisco IOS Release 12.2(50)SG and later

Switch(config)# interface gigabitethernet2/1

Switch(config-if)# authentication port-control auto

Switch(config-if)# authentication host-mode multi-host

Switch(config-if)# end

Cisco IOS Release 12.2(46)SG or earlier

Switch(config)# interface gigabitethernet2/1

Switch(config-if)# dot1x port-control auto

Switch(config-if)# dot1x host-mode multi-host

Switch(config-if)# end

This example shows how to enable MDA and to allow both a host and a 802.1X voice device (a Cisco or third-party phone with 802.1X supplicant) on the port:

Cisco IOS Release 12.2(50)SG and later

Switch# conf terminal

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)# interface FastEthernet3/1

Switch(config-if)# shut

Switch(config-if)# switchport access vlan 12

Switch(config-if)# switchport mode access

Switch(config-if)# switchport voice vlan 10

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# authentication port-control auto

Switch(config-if)# authentication host-mode multi-domain

Switch(config-if)# no shut

Switch(config-if)# end

Cisco IOS Release 12.2(46)SG or earlier

Switch# conf t

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)# interface FastEthernet3/1

Switch(config-if)# shut

Switch(config-if)# switchport access vlan 12

Switch(config-if)# switchport mode access

Switch(config-if)# switchport voice vlan 10

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x port-control auto

Switch(config-if)# dot1x host-mode multi-domain

Switch(config-if)# no shut

Switch(config-if)# end

This example shows how to enable MDA and to allow both a host and a non-802.1X voice device on the port:

Cisco IOS Release 12.2(50)SG and later

Switch# conf t

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)# interface FastEthernet3/1

Switch(config-if)# shut

Switch(config-if)# switchport access vlan 12

Switch(config-if)# switchport mode access

Switch(config-if)# switchport voice vlan 10

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# authentication port-control auto

Switch(config-if)# authentication host-mode multi-domain

Switch(config-if)# mab eap

Switch(config-if)# no shut

Switch(config-if)# end

Cisco IOS Release 12.2(46)SG or earlier

Switch# conf t

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)# interface FastEthernet3/1

Switch(config-if)# shut

Switch(config-if)# switchport access vlan 12

Switch(config-if)# switchport mode access

Switch(config-if)# switchport voice vlan 10

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x port-control auto

Switch(config-if)# dot1x host-mode multi-domain

Switch(config-if)# dot1x mac-auth-bypass

Switch(config-if)# no shut

Switch(config-if)# end

This example shows how to verify the dot1x MDA settings on interface FastEthernet3/1:

Switch# show dot1x interface FastEthernet3/1 detail

Dot1x Info for FastEthernet3/1

-----------------------------------

PAE                       = AUTHENTICATOR

PortControl               = AUTO

ControlDirection          = Both

HostMode                  = MULTI_DOMAIN

ReAuthentication          = Disabled

QuietPeriod               = 60

ServerTimeout             = 30

SuppTimeout               = 30

ReAuthPeriod              = 3600 (Locally configured)

ReAuthMax                 = 2

MaxReq                    = 2

TxPeriod                  = 30

RateLimitPeriod           = 0

Dot1x Authenticator Client List

-------------------------------

Domain                    = DATA

Supplicant                = 0000.0000.ab01

        Auth SM State     = AUTHENTICATED

        Auth BEND SM Stat = IDLE

Port Status               = AUTHORIZED

Authentication Method     = Dot1x

Authorized By             = Authentication Server

Vlan Policy               = 12

Domain                    = VOICE

Supplicant                = 0060.b057.4687

        Auth SM State     = AUTHENTICATED

        Auth BEND SM Stat = IDLE

Port Status               = AUTHORIZED

Authentication Method     = Dot1x

Authorized By             = Authentication Server

Switch#

This example shows how to enable MDA and to authentication of multiple hosts and a voice device on an IEEE 802.1x-authorized port:

Note This example applies to Cisco IOS Release 12.2(50)SG and later releases.

Switch# conf t

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)# interface FastEthernet3/1

Switch(config-if)# shut

Switch(config-if)# switchport access vlan 12

Switch(config-if)# switchport mode access

Switch(config-if)# switchport voice vlan 10

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# authentication port-control auto

Switch(config-if)# authentication host-mode multi-auth

Switch(config-if)# map eap

Switch(config-if)# no shut

Switch(config-if)# end

Configuring 802.1X Authentication with ACL Assignments and Redirect URLs

Topics include:

•Downloadable ACL

•URL-Redirect

•Configuring a Downloadable Policy

Downloadable ACL

The Downloadable ACL feature enables you to download device specific authorization policies from the authentication server. These policies activate after authentication succeeds for the respective client and the client's IP address has been populated in the IP device tracking table. (Downloadable ACL is applied on the port, once the port is authenticated and the IP device tracking table has the host IP address entry).

The following sections illustrates the configuration needed to complement the related authentication (802.1X or MAB) configuration. (No unique configuration is required on the switch. All of the configuration is on the ACS.) After authentication succeeds, enter the show ip access-list command to display the downloadable ACLs.

Switch Configuration

Step 1 Configure the IP device tracking table.

Switch(config)# ip device tracking

Step 2 Configure RADIUS VSA to forward authentication.

Switch(config)# radius-server vsa send authentication

Step 3 Configure Static ACL (PACL) for the interface.

Switch(config)# int g2/9

Switch(config-if)# ip access-group pacl-4 in

Sample Interface Configuration

Switch# show running-configuration interface g2/9

Building configuration...

Current configuration : 617 bytes

!

interface GigabitEthernet2/9

 switchport

 switchport access vlan 29

 switchport mode access

 switchport voice vlan 1234

 access-group mode prefer port

 ip access-group pacl-4 in 

 speed 100

 duplex full

 authentication event fail action authorize vlan 111

 authentication event server dead action authorize vlan 333

 authentication event server alive action reinitialize  

 authentication host-mode multi-auth

 authentication order dot1x

 authentication port-control auto

 authentication timer restart 100

 authentication timer reauthenticate 20

 authentication timer inactivity 200  

 mab eap

 dot1x pae authenticator

end       

Switch#

Switch# show ip access-list pacl-4

    10 permit ip host 1.1.1.1 host 2.2.2.2

    20 permit icmp host 1.1.1.1 host 2.2.2.2 

Switch#

Debug Commands for DACL

The IP device tracking table contains the host IP address learned through ARP or DHCP.

The following commands displays the constraints on the IP device tracking table:

Switch# show ip device tracking all

IP Device Tracking = Enabled

IP Device Tracking Probe Count = 3 

IP Device Tracking Probe Interval = 30

--------------------------------------------------------------

  IP Address     MAC Address       Interface          STATE   

--------------------------------------------------------------

50.0.0.12       0015.60a4.5e84 GigabitEthernet2/9     ACTIVE 

The following command shows that the EPM (Policy Enforced Module) session contains the DACL downloaded from ACS:

Switch# show epm session ip 50.0.0.12

Admission feature       : DOT1X

AAA Policies            :

ACS ACL                 : xACSACLx-IP-auth-48b79b6e 

The following command reveals the contents of the downloadable ACL:

Switch# show ip accesslists xACSACLx-IP-auth-48b79b6e

Extended IP access list xACSACLx-IP-auth-48b79b6e (per-user)

    10 permit udp any any

Switch(config)#

Cisco ACS Configuration for DACL

Note Only Cisco ACS supports DACL.

Follow these steps to ensure correct functioning of the ACS configuration required for DACL:

Step 1 Configure a downloadable IP ACL on the window that appears when you select
Radius Shared Profile > Downloadable IP ACL Content:

Figure 40-8 Shared Profile Components

Step 2 Attach this DACL with the USER on the window that appears when you select User > DACLs:

Figure 40-9 Downloadable ACLs

URL-Redirect

This configuration consists of two configurations: one on ACS, and one on the switch.

ACS configuration

To configure two Cisco-AV pairs, add the following statements under the user or group Cisco IOS/PIX 6x RADIUS attributes:

url-redirect-acl=urlacl 

url-redirect=http://www.cisco.com 

Note A default port ACL must be configured on the interface.

Switch configuration

To configure the switch for URL redirect, do the following:

Step 1 Configure the IP device tracking table.

Switch(config)# ip device tracking

Step 2 Configure RADIUS with the send authentication command.

Switch(config)# radius-server vsa send authentication 

Step 3 Configure the URL redirect ACL (URLACL).

Switch# ip access-list urlacl

    10 permit tcp any any 

Switch#

Step 4 Configure static ACL (PACL) for the interface.

Switch(config)# int g2/9 

Switch(config-if)# ip access-group pacl-4 in

Sample Interface Configuration

Switch# show running-configuration int g2/9

Building configuration...

Current configuration : 617 bytes

!

interface GigabitEthernet2/9

 switchport

 switchport access vlan 29

 switchport mode access

 switchport voice vlan 1234

 access-group mode prefer port

 ip access-group pacl-4 in

 speed 100

 duplex full

 authentication event fail action authorize vlan 111

 authentication event server dead action authorize vlan 333

 authentication event server alive action reinitialize  

 authentication host-mode multi-auth

 authentication order dot1x

 authentication port-control auto

 authentication timer restart 100

 authentication timer reauthenticate 20

 authentication timer inactivity 200

 mab  

 dot1x pae authenticator

end       

Switch#

Switch# show access-list pacl-4

    10 permit ip host 1.1.1.1 host 2.2.2.2

    20 permit icmp host 1.1.1.1 host 2.2.2.2

Switch#

Verify URL-redirect with the following commands.

The show ip device tracking command illustrates the constraints on the IP device tracking table:

Switch(config)# show ip device tracking all 

IP Device Tracking = Enabled 

IP Device Tracking Probe Count = 3 

IP Device Tracking Probe Interval = 30

--------------------------------------------------------------

  IP Address     MAC Address       Interface          STATE   

--------------------------------------------------------------

50.0.0.12       0015.60a4.5e84 GigabitEthernet2/9     ACTIVE

The show epm session ip command displays the EPM session table for a particular host. Observe the
URL- redirect-acl and URL-redirect URL information that downloads from the ACS.

Switch# show epm session ip 50.0.0.12

Admission feature       : DOT1X

AAA Policies            :

URL Redirect ACL        : urlacl 

URL Redirect            : http://www.cisco.com

For more information about AV pairs that are supported by Cisco IOS software, see the
ACS configuration and command reference documentation about the software releases running on the AAA clients.

Guidelines and Restrictions for DACL and URL Redirect

For downloadable ACL or URL redirect, the ACL source must be ANY
(permit TCP ANY host 1.1.1.1 eq 80 or permit TCP ANY host 1.1.1.1 eq 443).

Configuring a Downloadable Policy

To configure downloadable policies, perform this task:

Switch# configure terminal 

Switch(config)# access-list 
access-list-number {deny | permit} 
source [source-wildcard] [log] 

Switch(config-if)# interface 
interface-id 

Switch(config-if)# ip access-group 
{access-list-number | name} in 

Switch(config)# exit 

Switch(config)# aaa new-model

Switch(config)# aaa authorization 
network default local

Switch(config)# ip device tracking

Switch(config)# ip device tracking 
[probe {count count | interval 
interval}]

Switch(config)# ip device tracking 
[probe {delay interval}]

Switch(config)# radius-server vsa 
send authentication

Switch(config)# end

Switch# show ip device tracking 
{all | interface interface-id | ip 
ip-address | mac mac-address} 

Switch# copy running-config 
startup-config

The following example illustrates how to configure a switch for downloadable policy:

Switch# config terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)# aaa new-model

Switch(config)# aaa authorization network default local

Switch(config)# ip device tracking

Switch(config)# ip access-list extended default_acl

Switch(config-ext-nacl)# permit ip any any

Switch(config-ext-nacl)# exit

Switch(config)# radius-server vsa send authentication

Switch(config)# int fastEthernet 2/13

Switch(config-if)# ip access-group default_acl in

Switch(config-if)# exit

Configuring 802.1X Authentication with Per-User ACL and Filter-ID ACL

Topics include:

•Per-User ACL and Filter-ID ACL

•Configuring a Per-User ACL and Filter-ID ACL

Per-User ACL and Filter-ID ACL

Prior to Cisco IOS Release 12.2(52)SG, the Cat4K platform only supported downloadable ACLs, which work with the Cisco ACS server but not with third-party AAA servers. With
Cisco IOS Release 12.2(52)SG, the Catalyst 4500 switch offers the Filter-ID/Per-user-acl enhancement(s), which allow ACL policy enforcement using a third-party AAA server.

The Filter-ID feature provides the following capabilities:

Filter-ID option allows an administrator to define the ACL name on the AAA server using IETF standard Radius attribute. The ACL itself must be pre-configured locally on the switch.

The Per-user-acl feature provides the following capabilities:

Per-user ACL allows an administrator to define the per-user ACL on the AAA server using Cisco Radius AV pairs. This allows third-party AAA server to interoperate by loading Cisco Radius dictionary. Cisco radius dictionary will have Cisco Radius AV pairs configured as a VSA.

Note The Radius Vendor-specific attributes (VSAs) allow vendors to support their own proprietary RADIUS attributes that are not included in standard radius attributes.

Switch Configuration

Step 1 Configure the IP device tracking table.

Switch(config)# ip device tracking

Step 2 Configure Static ACL (PACL) for the interface.

Switch(config)# int g2/9

Switch(config-if)# ip access-group pacl-4 in

Sample Interface Configuration

Switch# show running-configuration interface g2/9

Building configuration...

Current configuration : 617 bytes

!

interface GigabitEthernet2/9

 switchport

 switchport access vlan 29

 switchport mode access

 switchport voice vlan 1234

 access-group mode prefer port

 ip access-group pacl-4 in 

 speed 100

 duplex full

 authentication event fail action authorize vlan 111

 authentication event server dead action authorize vlan 333

 authentication event server alive action reinitialize  

 authentication host-mode multi-auth

 authentication order dot1x

 authentication port-control auto

 authentication timer restart 100

 authentication timer reauthenticate 20

 authentication timer inactivity 200  

 mab eap

 dot1x pae authenticator

end       

Switch#

Switch# show ip access-list pacl-4

    10 permit ip host 1.1.1.1 host 2.2.2.2

    20 permit icmp host 1.1.1.1 host 2.2.2.2 

Switch#

Per-User-Acl configuration in ACS

In the Group/User Setting page, scroll down to the Cisco IOS/PIX 6.x RADIUS Attributes section. Select the box next to [009\001 cisco-av-pair] and enter the elements of the per-user ACL. Per-user ACLS take this format:

<protocol>:inacl#<sequence number>=<ACE>

<protocol> can be either "ip" for IP-based ACLs or "mac" for MAC-based ACLs.

In the following example, members of the group you are configuring are denied all access to the 10.100.60.0 subnet, denied http access to the server at 10.100.10.116, and permitted everywhere else.

Figure 40-10 Define the ACEs for the per-user ACL

Note outbound ACLs (outacl) are not supported.

Filter-Id configuration in ACS:

In the Group/User Setting page, scroll down to the " IETF RADIUS Attributes" section. Select the box next to [011] Filter-Id and enter the ACL to apply for members of this group (Figure 40-11).

The Filter-Id takes this format:

<ACL>.in

<ACL> is the number of the ACL that was configured on the switch in the previous step

Figure 40-11 Configuring the Filter-ID Attribute

Note Outbound ACLs (e.g. "100.out") are not supported.

Debug Commands for Per-User ACL and Filter-ID ACL

The IP device tracking table contains the host IP address learned through ARP or DHCP. The following command displays the constraints on the IP device tracking table:

Switch# show ip device tracking all

IP Device Tracking = Enabled

IP Device Tracking Probe Count = 3

IP Device Tracking Probe Interval = 30

--------------------------------------------------------------

IP Address MAC Address Interface STATE

--------------------------------------------------------------

50.0.0.12 0015.60a4.5e84 GigabitEthernet2/9 ACTIVE

The following command shows that the EPM (Policy Enforced Module) session contains the per-user-acl from ACS:

Switch# show epm session ip 50.0.0.12

Admission feature : DOT1X

AAA Policies :

Per-User ACL            : deny ip any host 20.20.10.10

The following command reveals the contents of the per-user-acl (note that per-user-acl are shown above the default port ACL configured on the interface, 151 is the default port ACL in the following example):

Switch# show access-list

Extended IP access list 151

     deny ip host 20.20.0.3 host 20.20.10.10

    10 permit ip any any (57 estimate matches)

The following commands reveals the number of sessions and the corresponding client ip addresses,

Switch# show epm session summary

EPM Session Information

-----------------------

Total sessions seen so far : 1

Total active sessions      : 1

Session IP Address :

-------------------

50.0.0.12

The following command shows that the EPM (Policy Enforced Module) session contains the per-user-acl(both ip and mac acl from ACS):

Switch# show epm session ip 50.0.0.12

Admission feature : DOT1X

AAA Policies :

Per-User ACL            : deny ip any host 20.20.10.10

Per-User ACL            : deny any host 0000.AAAA.AAAA

The following command reveals the contents of the per-user-acl (note that per-user-acl are shown above the default port acl configured on the interface, 151 is the default port acl in the example below):

Switch# show access-list

Extended IP access list 151

     deny ip host 20.20.0.3 host 20.20.10.10

    10 permit ip any any (57 estimate matches)

..

..

..(check for the mac access-list created)..

..

Extended MAC access list PerUser_MAC_ACL-589079192 (per-user)

    deny   any host 0000.aaaa.aaaa

..

The following command shows that the EPM (Policy Enforced Module) session contains the Filter-Id 155 from ACS:

Note The 156 IP extended acl is to be pre-configured on the switch, so that the policy enforcement can happen.

Switch# show ip access-list 156

Extended IP access list 156

    10 deny ip any host 155.155.155.156

    20 deny ip any 156.100.60.0 0.0.0.255

    30 deny tcp any host 156.100.10.116 eq www

Switch# show epm session ip 50.0.0.12

Admission feature : DOT1X

AAA Policies :

Filter-Id               : 155

The following command reveals the contents of the Filter-Id applied on the interface:

Switch# show ip access-list int <gi6/3>

Switch# show ip access-list interface gi6/3

     deny ip host 20.20.0.2 host 155.155.155.156

     deny ip host 20.20.0.2 156.100.60.0 0.0.0.255

     deny tcp host 20.20.0.2 host 156.100.10.116 eq www

Guidelines and Restrictions for Per-User-ACL and Filter-ID ACL

For Per-User-ACL and Filter-ID ACL, the ACL source must be ANY
(permit TCP ANY host 1.1.1.1 eq 80 or permit TCP ANY host 1.1.1.1 eq 443).

Configuring a Per-User ACL and Filter-ID ACL

To configure Per-User-ACL and Filter-ID ACL, perform this task:

Switch# configure terminal 

Switch(config)# access-list 
access-list-number {deny | permit} 
source [source-wildcard] [log] 

Switch(config-if)# interface 
interface-id 

Switch(config-if)# ip access-group 
{access-list-number | name} in 

Switch(config)# exit 

Switch(config)# aaa new-model

Switch(config)# aaa authorization 
network default local

Switch(config)# ip device tracking

Switch(config)# ip device tracking 
[probe {count count | interval 
interval}]

Switch(config)# ip device tracking 
[probe {delay interval}]

Switch(config)# end

Switch# show ip device tracking 
{all | interface interface-id | ip 
ip-address | mac mac-address} 

Switch# copy running-config 
startup-config

The following example illustrates how to configure a switch for downloadable policy:

Switch# config terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)# aaa new-model

Switch(config)# aaa authorization network default local

Switch(config)# ip device tracking

Switch(config)# ip access-list extended default_acl

Switch(config-ext-nacl)# permit ip any any

Switch(config-ext-nacl)# exit

Switch(config)# int fastEthernet 2/13

Switch(config-if)# ip access-group default_acl in

Switch(config-if)# exit

Configuring RADIUS-Provided Session Timeouts

You can configure the Catalyst 4500 series switch to use a RADIUS-provided reauthentication timeout.

To configure RADIUS-provided timeouts, perform this task:

Switch# configure terminal

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access

Switch(config-if)# dot1x pae 
authenticator

Cisco IOS Release 12.2(50)SG and later

Switch(config-if)# authentication 
timer reauthenticate {interface | 
server}

Cisco IOS Release 12.2(46)SG or earlier 
releases

Switch(config-if)# dot1x timeout 
reauth-attempts {interface | server}

Switch(config-if)# end

Switch# show dot1x interface 
interface-id details

Switch # copy running-config 
startup-config

This example shows how to configure a switch to derive the re-authentication period from the server and to verify the configuration:

Cisco IOS Release 12.2(50):

Switch# configure terminal

Switch(config)# interface f7/1

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# authentication timer reauthenticate server

Switch(config-if)# end

Switch# show dot1x interface f7/1 det

Dot1x Info for FastEthernet7/11

-----------------------------------

PAE                       = AUTHENTICATOR

PortControl               = FORCE_AUTHORIZED

ControlDirection          = Both 

HostMode                  = SINGLE_HOST

ReAuthentication          = Disabled

QuietPeriod               = 60

ServerTimeout             = 30

SuppTimeout               = 30

ReAuthPeriod              = (From Authentication Server)

ReAuthMax                 = 2

MaxReq                    = 2

TxPeriod                  = 30

RateLimitPeriod           = 0

Dot1x Authenticator Client List Empty

Port Status               = AUTHORIZED

Switch#

Cisco IOS Release 12.2(46) or earlier

Switch# configure terminal

Switch(config)# interface f7/1

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x timeout reauth-attempts server

Switch(config-if)# end

Switch# show dot1x interface f7/1 det

Dot1x Info for FastEthernet7/11

-----------------------------------

PAE                       = AUTHENTICATOR

PortControl               = FORCE_AUTHORIZED

ControlDirection          = Both 

HostMode                  = SINGLE_HOST

ReAuthentication          = Disabled

QuietPeriod               = 60

ServerTimeout             = 30

SuppTimeout               = 30

ReAuthPeriod              = (From Authentication Server)

ReAuthMax                 = 2

MaxReq                    = 2

TxPeriod                  = 30

RateLimitPeriod           = 0

Dot1x Authenticator Client List Empty

Port Status               = AUTHORIZED

Switch#

Configuring Violation Action

You can configure 802.1X security violation behavior as either shutdown or restrict mode, based on the response to the violation.

To configure the violation action, performing the following task:

Switch# configure terminal

Switch(config)# interface 
interface-id

Switch(config-if)# authentication 

violation [restrict | 

shutdown]

Switch(config-if)# end

Switch# show run

Switch # copy running-config 
startup-config

This example shows how to configure violation mode shutdown on a switch:

Switch# configure terminal

Switch(config)# authentication violation shutdown

A port is error-disabled when a security violation triggers on shutdown mode. The following syslog messages displays:

%AUTHMGR-5-SECURITY_VIOLATION: Security violation on the interface <interface name>, new 
MAC address <mac-address> is seen.

%PM-4-ERR_DISABLE: security-violation error detected on <interface name>, putting 
<interface name> in err-disable state

Configuring 802.1X with Guest VLANs

You can configure a guest VLAN for each 802.1X port on the Catalyst 4500 series switch to provide limited services to clients, such as downloading the 802.1X client. These clients might be upgrading their system for 802.1X authentication, and some hosts, such as Windows 98 systems, might not be 802.1X-capable.

When you enable a guest VLAN on an 802.1X port, the Catalyst 4500 series switch assigns clients to a guest VLAN provided (1) the authentication server does not receive a response to its EAPOL request or identity frame, or (2) the EAPOL packets are not sent by the client.

Starting with Cisco IOS Release 12.2(25)EWA, the Catalyst 4500 series switch maintains the EAPOL packet history. If another EAPOL packet is detected on the interface during the lifetime of the link, network access is denied. The EAPOL history is reset upon loss of the link.

Any number of 802.1X-incapable clients are allowed access when the switch port is moved to the guest VLAN. If an 802.1X-capable client joins the same port on which the guest VLAN is configured, the port is put into the unauthorized state in the user-configured access VLAN, and authentication is restarted.

Guest VLANs are supported on 802.1X ports in single-host or multiple-hosts mode.

Note When a port is put into a guest VLAN, it is automatically placed into multihost mode, and an unlimited number of hosts can connect through the port. Changing the multihost configuration does not effect a port in a guest VLAN.

Note Except for an RSPAN VLAN or a voice VLAN, you can configure any active VLAN as an 802.1X guest VLAN.

To configure 802.1X with guest VLAN on a port, perform this task:

Switch# configure terminal

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access 
or 
Switch(config-if)# switchport mode 
private-vlan host

Switch(config-if)# dot1x pae 
authenticator

Cisco IOS Release 12.2(50)SG and later

Switch(config-if)# authentication 
event no-response action authorize 
vlan vlan-id

Cisco IOS Release 12.2(46)SG or earlier 
releases

Switch(config-if)# dot1x guest-vlan 
vlan-id

Cisco IOS Release 12.2(50)SG and later

Switch(config-if)# authentication 
port-control auto

Cisco IOS Release 12.2(46)SG or earlier 
releases

Switch(config-if)# dot1x 
port-control auto

Switch(config-if)# end

Switch(config)# end

This example shows how to enable regular VLAN 50 on Fast Ethernet 4/3 as a guest VLAN on a static access port:

Cisco IOS Release 12.2(50)SG and later

Switch# configure terminal

Switch(config)# interface fa4/3

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# authentication event no-response action authorize vlan 50

Switch(config-if)# authentication port-control auto

Switch(config-if)# end

Switch#

Cisco IOS Release 12.2(46)SG or earlier

Switch# configure terminal

Switch(config)# interface fa4/3

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x guest-vlan 50

Switch(config-if)# dot1x port-control auto

Switch(config-if)# end

Switch#

This example shows how to enable a secondary PVLAN 100 as a guest VLAN on a PVLAN host port:

Cisco IOS Release 12.2(50)SG and later

Switch# configure terminal

Switch(config)# interface fa4/3

Switch(config-if)# switchport mode private-vlan host

Switch(config-if)# authentication port-control auto

Switch(config-if)# authentication event no-response action authorize vlan 100

Switch(config-if)# end

Switch#

Cisco IOS Release 12.2(46)SG or earlier

Switch# configure terminal

Switch(config)# interface fa4/3

Switch(config-if)# switchport mode private-vlan host

Switch(config-if)# dot1x port-control auto

Switch(config-if)# dot1x guest-vlan 100

Switch(config-if)# end

Switch#

To allow supplicants into a guest VLAN on a switch, perform this task:

Switch# configure terminal

Switch# dot1x guest-vlan supplicant

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access 
or 
Switch(config-if)# switchport mode 
private-vlan host

Switch(config-if)# dot1x pae 
authenticator

Switch(config-if)# dot1x guest-vlan 
vlan-id

Cisco IOS Release 12.2(50)SG and later

Switch(config-if)# authentication 
port-control auto

Cisco IOS Release 12.2(46)SG or earlier 
releases

Switch(config-if)# dot1x 
port-control auto

Switch(config-if)# end

Switch# show dot1x interface 
interface-id

Switch# copy running-config 
startup-config

This example shows how to enable the guest VLAN feature and to specify VLAN 5 as a guest VLAN:

Cisco IOS Release 12.2(50)SG and later

Switch# configure terminal

Switch(config)# dot1x guest-vlan supplicant

Switch(config)# interface gigabitethernet5/9

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# authentication event no-response action authorize vlan 5

Switch(config-if)# authentication port-control auto

Switch(config-if)# end

Switch#

Cisco IOS Release 12.2(46)SG or earlier

Switch# configure terminal

Switch(config)# dot1x guest-vlan supplicant

Switch(config)# interface gigabitethernet5/9

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x guest-vlan 5

Switch(config-if)# dot1x port-control auto

Switch(config-if)# end

Switch#

Configuring 802.1X with MAC Authentication Bypass

To enable MAB, perform this task:

Switch# configure terminal

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access 
or 
Switch(config-if)# switchport mode 
private-vlan host

Switch(config-if)# dot1x pae 
authenticator

Cisco IOS Release 12.2(50)SG and later

Switch(config-if)# authentication 
port-control auto

Cisco IOS Release 12.2(46)SG or earlier 
releases

Switch(config-if)# dot1x 
port-control auto

Cisco IOS Release 12.2(50)SG and later

Switch(config-if)# mab [eap]

Cisco IOS Release 12.2(46)SG or earlier 
releases

Switch(config-if)# dot1x 
mac-auth-bypass [eap]

Switch(config)# end

Switch# show mab interface 
interface-id details

Switch# copy running-config 
startup-config

Note Removing a 802.1X MAB configuration from a port does not impact the authorized or authenticated state of the port. If the port is in an unauthenticated state, it remains in that state. If the port is in an authenticated state because of MAB, the switch reverts to the 802.1X Authenticator. If the port was already authorized with a MAC address and the MAB configuration was removed, the port remains in an authorized state until re-authentication occurs. At that time, if an 802.1X supplicant is detected on the wire, the MAC address is removed.

This example shows how to enable MAB on Gigabit Ethernet interface 3/3 and to verify the configuration:

Cisco IOS Release 12.2(50)SG and later

Switch# configure terminal

Switch(config)# interface gigabitethernet3/3

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# authentication port-control auto

Switch(config-if)# mab

Switch(config-if)# end

Switch# show mab int g3/3 details

MAB details for GigabitEthernet3/3

-------------------------------------

Mac-Auth-Bypass           = Enabled

MAB Client List

---------------

Client MAC                = 0001.0001.0001

Session ID                = C0A8016F0000002304175914

MAB SM state              = TERMINATE

Auth Status               = AUTHORIZED

Cisco IOS Release 12.2(46)SG or earlier

Switch# configure terminal

Switch(config)# interface gigabitethernet3/3

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x port-control auto

Switch(config-if)# dot1x mac-auth-bypass

Switch(config-if)# end

Switch# show dot1x int g3/3 details

Dot1x Info for GigabitEthernet3/3

-----------------------------------

PAE                       = AUTHENTICATOR

PortControl               = AUTO

ControlDirection          = Both 

HostMode                  = SINGLE_HOST

ReAuthentication          = Disabled

QuietPeriod               = 60

ServerTimeout             = 30

SuppTimeout               = 30

ReAuthPeriod              = 3600 (Locally configured)

ReAuthMax                 = 2

MaxReq                    = 2

TxPeriod                  = 1

RateLimitPeriod           = 0

Mac-Auth-Bypass           = Enabled

Dot1x Authenticator Client List

-------------------------------

Supplicant                = 0000.0000.0001

 Auth SM State     = AUTHENTICATED

 Auth BEND SM Stat = IDLE

Port Status               = AUTHORIZED

Authentication Method     = MAB

Authorized By             = Authentication Server

Vlan Policy               = N/A

Switch#

Configuring 802.1X with Inaccessible Authentication Bypass

Caution You must configure the switch to monitor the state of the RADIUS server as described in the section Configuring Switch-to-RADIUS-Server Communication for Inaccessible Authentication Bypass to work properly. Specifically, you must configure the RADIUS test username, idle-time, deadtime and dead-criteria. Failure to do so results in the switch failing to detect that the RADIUS server has gone down, or prematurely marking a dead RADIUS server as alive again.

To configure a port as a critical port and to enable the Inaccessible Authentication Bypass feature, perform this task:

Switch# configure terminal

Cisco IOS Release 12.2(50)SG and later

Switch(config)# authentication 
critical eapol

Cisco IOS Release 12.2(46)SG or earlier 
releases

Switch(config)# dot1x critical 
eapol

Cisco IOS Release 12.2(50)SG and later

Switch(config)# authentication 
critical recovery delay msec

Cisco IOS Release 12.2(46)SG or earlier 
releases

Switch(config)# dot1x critical 
recovery delay msec

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access 
or 
Switch(config-if)# switchport mode 
private-vlan host

Switch(config-if)# dot1x pae 
authenticator

Switch(config-if)# authentication 
port-control auto

Cisco IOS Release 12.2(50)SG and later

Switch(config-if)# authentication 
event server dead action authorize 
[vlan vlan-id]

Cisco IOS Release 12.2(46)SG or earlier 
releases

Switch(config-if)# dot1x critical

Cisco IOS Release 12.2(46)SG or earlier 
releases

Switch(config-if)# dot1x critical 
vlan vlan

Cisco IOS Release 12.2(50)SG and later

Switch(config-if)# authentication 
event server alive action 
reinitialize

Cisco IOS Release 12.2(46)SG or earlier 
releases

Switch(config-if)# dot1x critical 
recovery action reinitialize

Switch(config)# end

Switch# show dot1x interface 
interface-id details

Switch# copy running-config 
startup-config

The following example shows a full configuration of 802.1X with Inaccessible Authentication Bypass, including required AAA and RADIUS configuration as specified in the "Enabling 802.1X Authentication" sectionand "Configuring Switch-to-RADIUS-Server Communication" section.

The RADIUS server configured is at IP address 10.1.2.3, using port 1645 for authentication and 1646 for accounting. The RADIUS secret key is mykey. The username used for the test server probes is randomuser. The test probes for both living and dead servers are generated once per minute. The interface FastEthernet 3/1 is configured to critically authenticate into VLAN 17 when AAA becomes unresponsive, and to reinitialize automatically when AAA becomes available again.

Cisco IOS Release 12.2(50)SG and later

Switch# configure terminal

Switch(config)# aaa new-model

Switch(config)# aaa authentication dot1x default group radius

Switch(config)# dot1x system-auth-control

Switch(config)# radius-server host 10.1.2.3 auth-port 1645 acct-port 1646 test username 
randomuser idle-time 1 key mykey

Switch(config)# radius deadtime 1

Switch(config)# radius dead-criteria time 15 tries 3

Switch(config)# interface f3/1

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# authentication port-control auto

Switch(config-if)# authentication event server dead action authorize vlan 17

Switch(config-if)# end

Switch# show dot1x int fastethernet 3/1 details

Dot1x Info for FastEthernet3/1

-----------------------------------

PAE                       = AUTHENTICATOR

PortControl               = AUTO

ControlDirection          = Both

HostMode                  = SINGLE_HOST

ReAuthentication          = Disabled

QuietPeriod               = 60

ServerTimeout             = 30

SuppTimeout               = 30

ReAuthPeriod              = 3600 (Locally configured)

ReAuthMax                 = 2

MaxReq                    = 2

TxPeriod                  = 30

RateLimitPeriod           = 0

Critical-Auth             = Enabled

Critical Recovery Action  = Reinitialize

Critical-Auth VLAN        = 17

Dot1x Authenticator Client List

-------------------------------

Supplicant                = 0000.0000.0001

Auth SM State     = AUTHENTICATING

Auth BEND SM Stat = RESPONSE

Port Status               = AUTHORIZED

Authentication Method     = Dot1x

Authorized By             = Critical-Auth

Operational HostMode      = SINGLE_HOST

Vlan Policy               = 17

Switch#

Cisco IOS Release 12.2(46)SG or earlier

Switch# configure terminal

Switch(config)# aaa new-model

Switch(config)# aaa authentication dot1x default group radius

Switch(config)# dot1x system-auth-control

Switch(config)# radius-server host 10.1.2.3 auth-port 1645 acct-port 1646 test username 
randomuser idle-time 1 key mykey

Switch(config)# radius deadtime 1

Switch(config)# radius dead-criteria time 15 tries 3

Switch(config)# interface f3/1

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x port-control auto

Switch(config-if)# dot1x critical

Switch(config-if)# dot1x critical vlan 17

Switch(config-if)# dot1x critical recovery action reinitialize

Switch(config-if)# end

Switch# show dot1x int fastethernet 3/1 details

Dot1x Info for FastEthernet3/1

-----------------------------------

PAE                       = AUTHENTICATOR

PortControl               = AUTO

ControlDirection          = Both

HostMode                  = SINGLE_HOST

ReAuthentication          = Disabled

QuietPeriod               = 60

ServerTimeout             = 30

SuppTimeout               = 30

ReAuthPeriod              = 3600 (Locally configured)

ReAuthMax                 = 2

MaxReq                    = 2

TxPeriod                  = 30

RateLimitPeriod           = 0

Critical-Auth             = Enabled

Critical Recovery Action  = Reinitialize

Critical-Auth VLAN        = 17

Dot1x Authenticator Client List

-------------------------------

Supplicant                = 0000.0000.0001

Auth SM State     = AUTHENTICATING

Auth BEND SM Stat = RESPONSE

Port Status               = AUTHORIZED

Authentication Method     = Dot1x

Authorized By             = Critical-Auth

Operational HostMode      = SINGLE_HOST

Vlan Policy               = 17

Switch#

Configuring 802.1X with Unidirectional Controlled Port

To configure unidirectional controlled port, perform this task:

Switch# configure terminal

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access 
or 
Switch(config-if)# switchport mode 
private-vlan host

Switch(config-if)# dot1x pae 
authenticator

Switch(config-if)# authentication 
port-control auto

Cisco IOS Release 12.2(50)SG and later

Switch(config-if)# authentication 
control-direction {in | both}

Cisco IOS Release 12.2(46)SG or earlier 
releases

Switch(config-if)# dot1x 
control-direction {in | both}

Switch(config)# end

Switch# show dot1x interface 
interface-id details

Switch# copy running-config 
startup-config

Note Unidirectional Controlled Port only works when Spanning Tree Portfast is enabled on the port. Unidirectional Controlled Port and Spanning Tree Portfast should be configured on a switch port that connects to a host. If two such ports are connected together with an Ethernet cable, high CPU utilization may result because host learning will be flapping between the two ports.

This example shows how to enable unidirectional port control:

Cisco IOS Release 12.2(50)SG and later

Switch# configure terminal

Switch(config)# interface gigabitethernet3/3

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# authentication port-control auto

Switch(config-if)# authentication control-direction in

Switch(config-if)# end

Switch# show dot1x int g3/3

Dot1x Info for GigabitEthernet3/3

-----------------------------------

PAE                       = AUTHENTICATOR

PortControl               = AUTO

ControlDirection          = In

HostMode                  = SINGLE_HOST

ReAuthentication          = Disabled

QuietPeriod               = 60

ServerTimeout             = 30

SuppTimeout               = 30

ReAuthPeriod              = 3600 (Locally configured)

ReAuthMax                 = 2

MaxReq                    = 2

TxPeriod                  = 30

RateLimitPeriod           = 0

Switch#

Cisco IOS Release 12.2(46)SG or earlier

Switch# configure terminal

Switch(config)# interface gigabitethernet3/3

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# authentication port-control auto

Switch(config-if)# dot1x control-direction in

Switch(config-if)# end

Switch# show dot1x int g3/3

Dot1x Info for GigabitEthernet3/3

-----------------------------------

PAE                       = AUTHENTICATOR

PortControl               = AUTO

ControlDirection          = In

HostMode                  = SINGLE_HOST

ReAuthentication          = Disabled

QuietPeriod               = 60

ServerTimeout             = 30

SuppTimeout               = 30

ReAuthPeriod              = 3600 (Locally configured)

ReAuthMax                 = 2

MaxReq                    = 2

TxPeriod                  = 30

RateLimitPeriod           = 0

Switch#

Configuring 802.1X with Authentication Failed

By configuring authentication-failed VLAN alignment on any Layer 2 port on the Catalyst 4500 series switch, you can provide limited network services to clients that fail the authentication process.

Note You can use authentication-failed VLAN assignment with other security features, such as Dynamic ARP Inspection (DAI), Dynamic Host Configuration Protocol (DHCP) snooping, and IP Source Guard. Each of these features can be enabled and disabled independently on the authentication-failed VLAN.

To configure 802.1X with authentication-failed VLAN assignment, perform this task:

Switch# configure terminal

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access

Switch(config-if)# authentication 
port-control auto

Cisco IOS Release 12.2(50)SG and later

Switch(config-if)# authentication 
event fail action authorize vlan 
vlan-id

Cisco IOS Release 12.2(46)SG or earlier 
releases

Switch(config-if)# dot1x auth-fail 
vlan vlan-id

Cisco IOS Release 12.2(50)SG and later

Switch(config-if)# authentication 
event fail retry max-attempts 
action [authorize vlan vlan-id | 
next-method]

Cisco IOS Release 12.2(46)SG or earlier 
releases

Switch(config-if)# dot1x auth-fail 
max-attempts max-attempts

Switch(config-if)# end

Switch(config)# end

Switch# show dot1x interface 
interface-id details

Switch# copy running-config 
startup-config

This example shows how to enable a regular VLAN 40 on Fast Ethernet 4/3 as a authentication-failed VLAN on a static access port:

Cisco IOS Release 12.2(50)SG and later

Switch# configure terminal

Switch(config)# interface gigabitEthernet3/1

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# authentication port-control auto

Switch(config-if)# authentication event fail retry 5 action authorize vlan 40

Switch(config-if)# end

Switch# show dot1x all

Sysauthcontrol              Enabled

Dot1x Protocol Version            2

Dot1x Info for GigabitEthernet3/1

-----------------------------------

PAE                       = AUTHENTICATOR

PortControl               = AUTO

ControlDirection          = Both

HostMode                  = SINGLE_HOST

QuietPeriod               = 60

ServerTimeout             = 0

SuppTimeout               = 30

ReAuthMax                 = 2

MaxReq                    = 2

TxPeriod                  = 30

Switch#

Cisco IOS Release 12.2(46)SG or earlier

Switch# configure terminal

Switch(config)# interface gigabitEthernet3/1 

Switch(config-if)# switchport mode access 

Switch(config-if)# dot1x port-control auto 

Switch(config-if)# dot1x auth-fail vlan 40 

Switch(config-if)# dot1x auth-fail max-attempts 3 

Switch# show dot1x all

Sysauthcontrol              Enabled

Dot1x Protocol Version            2

Critical Recovery Delay         100

Critical EAPOL             Disabled

Dot1x Info for GigabitEthernet3/1

-----------------------------------

PAE                       = AUTHENTICATOR

PortControl               = AUTO

ControlDirection          = Both

HostMode                  = SINGLE_HOST

ReAuthentication          = Disabled

QuietPeriod               = 60

ServerTimeout             = 0

SuppTimeout               = 30

ReAuthPeriod              = 3600 (Locally configured)

ReAuthMax                 = 2

MaxReq                    = 2

TxPeriod                  = 5

RateLimitPeriod           = 0

Auth-Fail-Vlan            = 40

Auth-Fail-Max-attempts    = 3

Switch#

Configuring 802.1X with Voice VLAN

Note You must configure 802.1X and voice VLAN simultaneously.

Note You cannot configure an authentication-failed VLAN and a voice VLAN on the same port. When you try to configure these two features on the same port, a syslog message appears.

To enable 802.1X with voice VLAN, perform this task:

Switch# configure terminal

Switch(config)# interface 
interface-id

Switch(config-if)# switchport 
access vlan vlan-id

Switch(config-if)# switchport mode 
access

Switch(config-if)# switchport voice 
vlan vlan-id

Switch(config-if)# dot1x pae 
authenticator

Cisco IOS Release 12.2(50)SG and later 
and later

Switch(config-if)# authentication 
port-control auto

Cisco IOS Release 12.2(46)SG or earlier 
releases

Switch(config-if)# dot1x 
port-control auto

Switch(config-if)# end

Switch(config)# end

Switch# show dot1x interface 
interface-id details

Switch# copy running-config 
startup-config

This example shows how to enable 802.1X with voice VLAN feature on Fast Ethernet interface 5/9:

Cisco IOS Release 12.2(50)SG and later

Switch# configure terminal

Switch(config)# interface fastethernet5/9

Switch(config-if)# switchport access vlan 2

Switch(config-if)# switchport mode access

Switch(config-if)# switchport voice vlan 10

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# authentication port-control auto

Switch(config-if)# end

Switch(config# end

Switch#

Cisco IOS Release 12.2(46)SG or earlier

Switch# configure terminal

Switch(config)# interface fastethernet5/9

Switch(config-if)# switchport access vlan 2

Switch(config-if)# switchport mode access

Switch(config-if)# switchport voice vlan 10

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x port-control auto

Switch(config-if)# end

Switch(config# end

Switch#

Configuring 802.1X with VLAN Assignment

For enabling dynamic VLAN assignment, there is no additional configuration required in the switch. For configuring MDA or Multi-authentication refer "Configuring Multiple Domain Authentication and Multiple Authorization" section on page 39-29. To enable VLAN assignment, Cisco ACS Server has to be configured correspondingly.

To enable 802.1X with VLAN assignment, perform this task:

Switch# configure terminal

Switch(config)# interface 
interface-id

Switch(config-if)# switchport 
access vlan-id

Switch(config-if)# switchport mode 
access

Switch(config-if)# switchport voice 
vlan vlan-id

Switch(config-if)# authentication 
host-mode multi-domain