Catalyst 6500 Release 15.0SY Software Configuration Guide

Port Security

•Prerequisites for Port Security

•Restrictions for Port Security

•Information About Port Security

•Default Port Security Configuration

•How to Configure Port Security

•Verifying the Port Security Configuration

Note•For complete syntax and usage information for the commands used in this chapter, see these publications:

http://www.cisco.com/en/US/products/ps11845/prod_command_reference_list.html

•Cisco IOS Release 15.0SY supports only Ethernet interfaces. Cisco IOS Release 15.0SY does not support any WAN features or commands.

Tip For additional information about Cisco Catalyst 6500 Series Switches (including configuration examples and troubleshooting information), see the documents listed on this page:

http://www.cisco.com/en/US/products/hw/switches/ps708/tsd_products_support_series_home.html

Participate in the Technical Documentation Ideas forum

Prerequisites for Port Security

None.

Restrictions for Port Security

•With the default port security configuration, to bring all secure ports out of the error-disabled state, enter the errdisable recovery cause psecure-violation global configuration command, or manually reenable the port by entering the shutdown and no shut down interface configuration commands.

•Enter the clear port-security dynamic global configuration command to clear all dynamically learned secure addresses.

•Port security learns unauthorized MAC addresses with a bit set that causes traffic to them or from them to be dropped. The show mac address-table command displays the unauthorized MAC addresses, but does not display the state of the bit. (CSCeb76844)

•To preserve dynamically learned sticky MAC addresses and configure them on a port following a bootup or a reload and after the dynamically learned sticky MAC addresses have been learned, you must enter a write memory or copy running-config startup-config command to save them in the startup-config file.

•Port security supports private VLAN (PVLAN) ports.

•Port security supports IEEE 802.1Q tunnel ports.

•Port security does not support Switch Port Analyzer (SPAN) destination ports.

•Port security supports access and trunking EtherChannel port-channel interfaces.

•You can configure port security and 802.1X port-based authentication on the same port.

•Port security supports nonnegotiating trunks.

–Port security only supports trunks configured with these commands:

switchport
switchport trunk encapsulation
switchport mode trunk
switchport nonegotiate

–If you reconfigure a secure access port as a trunk, port security converts all the sticky and static secure addresses on that port that were dynamically learned in the access VLAN to sticky or static secure addresses on the native VLAN of the trunk. Port security removes all secure addresses on the voice VLAN of the access port.

–If you reconfigure a secure trunk as an access port, port security converts all sticky and static addresses learned on the native VLAN to addresses learned on the access VLAN of the access port. Port security removes all addresses learned on VLANs other than the native VLAN.

Note Port security uses the VLAN ID configured with the switchport trunk native vlan command.

•Take care when you enable port security on the ports connected to the adjacent switches when there are redundant links running between the switches because port security might error-disable the ports due to port security violations.

Information About Port Security

•Port Security with Dynamically Learned and Static MAC Addresses

•Port Security with Sticky MAC Addresses

•Port Security with IP Phones

Port Security with Dynamically Learned and Static MAC Addresses

You can use port security with dynamically learned and static MAC addresses to restrict a port's ingress traffic by limiting the MAC addresses that are allowed to send traffic into the port. When you assign secure MAC addresses to a secure port, the port does not forward ingress traffic that has source addresses outside the group of defined addresses. If you limit the number of secure MAC addresses to one and assign a single secure MAC address, the device attached to that port has the full bandwidth of the port.

A security violation occurs in either of these situations:

•When the maximum number of secure MAC addresses is reached on a secure port and the source MAC address of the ingress traffic is different from any of the identified secure MAC addresses, port security applies the configured violation mode.

•If traffic with a secure MAC address that is configured or learned on one secure port attempts to access another secure port in the same VLAN, applies the configured violation mode.

Note After a secure MAC address is configured or learned on one secure port, the sequence of events that occurs when port security detects that secure MAC address on a different port in the same VLAN is known as a MAC move violation.

See the "Configuring the Port Security Violation Mode on a Port" section for more information about the violation modes.

After you have set the maximum number of secure MAC addresses on a port, port security includes the secure addresses in the address table in one of these ways:

•You can statically configure all secure MAC addresses by using the switchport port-security mac-address mac_address interface configuration command.

•You can allow the port to dynamically configure secure MAC addresses with the MAC addresses of connected devices.

•You can statically configure a number of addresses and allow the rest to be dynamically configured.

If the port has a link-down condition, all dynamically learned addresses are removed.

Following bootup, a reload, or a link-down condition, port security does not populate the address table with dynamically learned MAC addresses until the port receives ingress traffic.

A security violation occurs if the maximum number of secure MAC addresses have been added to the address table and the port receives traffic from a MAC address that is not in the address table.

You can configure the port for one of three violation modes: protect, restrict, or shutdown. See the "How to Configure Port Security" section.

To ensure that an attached device has the full bandwidth of the port, set the maximum number of addresses to one and configure the MAC address of the attached device.

Port Security with Sticky MAC Addresses

Port security with sticky MAC addresses provides many of the same benefits as port security with static MAC addresses, but sticky MAC addresses can be learned dynamically. Port security with sticky MAC addresses retains dynamically learned MAC addresses during a link-down condition.

If you enter a write memory or copy running-config startup-config command, then port security with sticky MAC addresses saves dynamically learned MAC addresses in the startup-config file and the port does not have to learn addresses from ingress traffic after bootup or a restart.

Port Security with IP Phones

Figure 83-1 Device Connected Through IP Phone

Because the device is not directly connected to the switch, the switch cannot physically detect a loss of port link if the device is disconnected. Later Cisco IP phones send a Cisco Discovery Protocol (CDP) host presence type length value (TLV) to notify the switch of changes in the attached device's port link state. The switch recognizes the host presence TLV. Upon receiving a host presence TLV notification of a link down on the IP phone's data port, port security removes from the address table all static, sticky, and dynamically learned MAC addresses. The removed addresses are added again only when the addresses are learned dynamically or configured.

Default Port Security Configuration

How to Configure Port Security

•Enabling Port Security

•Configuring the Port Security Violation Mode on a Port

•Configuring the Maximum Number of Secure MAC Addresses on a Port

•Enabling Port Security with Sticky MAC Addresses on a Port

•Configuring a Static Secure MAC Address on a Port

•Configuring Secure MAC Address Aging on a Port

Enabling Port Security

•Enabling Port Security on a Trunk

•Enabling Port Security on an Access Port

Enabling Port Security on a Trunk

Port security supports nonnegotiating trunks.

Caution Because the default number of secure addresses is one and the default violation action is to shut down the port, configure the maximum number of secure MAC addresses on the port before you enable port security on a trunk (see "Configuring the Maximum Number of Secure MAC Addresses on a Port" section).

To enable port security on a trunk, perform this task:

This example shows how to configure Gigabit Ethernet port 5/36 as a nonnegotiating trunk and enable port security:

Router# configure terminal 

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)# interface gigabitethernet 5/36 

Router(config-if)# switchport 

Router(config-if)# switchport mode trunk 

Router(config-if)# switchport nonegotiate 

Router(config-if)# switchport port-security 

Router(config-if)# do show port-security interface gigabitethernet 5/36 | include Port 
Security 

Port Security              : Enabled

Enabling Port Security on an Access Port

To enable port security on an access port, perform this task:

This example shows how to enable port security on Gigabit Ethernet port 5/12:

Router# configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)# interface gigabitethernet 5/12

Router(config-if)# switchport 

Router(config-if)# switchport mode access

Router(config-if)# switchport port-security

Router(config-if)# do show port-security interface gigabitethernet 5/12 | include Port Security

Port Security              : Enabled

Configuring the Port Security Violation Mode on a Port

To configure the port security violation mode on a port, perform this task:

•protect—The PFC drops packets with unknown source addresses until you remove a sufficient number of secure MAC addresses to drop below the maximum value.

•restrict—The PFC drops packets with unknown source addresses until you remove a sufficient number of secure MAC addresses to drop below the maximum value and causes the security violation counter to increment.

•shutdown—Puts the interface into the error-disabled state immediately and sends an SNMP trap notification.

Note To bring a secure port out of the error-disabled state, enter the errdisable recovery cause violation_mode global configuration command, or you can manually reenable it by entering the shutdown and no shut down interface configuration commands.

This example shows how to configure the protect security violation mode on Gigabit Ethernet port 5/12:

Router# configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)# interface gigabitethernet 5/12

Router(config-if)# switchport port-security violation protect 

Router(config-if)# do show port-security interface gigabitethernet 5/12 | include Protect

Violation Mode             : Protect

This example shows how to configure the restrict security violation mode on Gigabit Ethernet port 5/12:

Router# configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)# interface gigabitethernet 5/12

Router(config-if)# switchport port-security violation restrict 

Router(config-if)# do show port-security interface gigabitethernet 5/12 | include Restrict

Violation Mode             : Restrict

Configuring the Maximum Number of Secure MAC Addresses on a Port

To configure the maximum number of secure MAC addresses on a port, perform this task:

•The range for number_of_addresses is 1 to 4,097.

•Port security supports trunks.

–On a trunk, you can configure the maximum number of secure MAC addresses both on the trunk and for all the VLANs on the trunk.

–You can configure the maximum number of secure MAC addresses on a single VLAN or a range of VLANs.

–For a range of VLANs, enter a dash-separated pair of VLAN numbers.

–You can enter a comma-separated list of VLAN numbers and dash-separated pairs of VLAN numbers.

This example shows how to configure a maximum of 64 secure MAC addresses on Gigabit Ethernet port 5/12:

Router# configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)# interface gigabitethernet 5/12

Router(config-if)# switchport port-security maximum 64 

Router(config-if)# do show port-security interface gigabitethernet 5/12 | include Maximum

Maximum MAC Addresses      : 64

Enabling Port Security with Sticky MAC Addresses on a Port

To enable port security with sticky MAC addresses on a port, perform this task:

•When you enter the switchport port-security mac-address sticky command:

–All dynamically learned secure MAC addresses on the port are converted to sticky secure MAC addresses.

–Static secure MAC addresses are not converted to sticky MAC addresses.

–Secure MAC addresses dynamically learned in a voice VLAN are not converted to sticky MAC addresses.

–New dynamically learned secure MAC addresses are sticky.

•When you enter the no switchport port-security mac-address sticky command, all sticky secure MAC addresses on the port are converted to dynamic secure MAC addresses.

•To preserve dynamically learned sticky MAC addresses and configure them on a port following a bootup or a reload, after the dynamically learned sticky MAC addresses have been learned, you must enter a write memory or copy running-config startup-config command to save them in the startup-config file.

This example shows how to enable port security with sticky MAC addresses on Gigabit Ethernet port 5/12:

Router# configure terminal 

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)# interface gigabitethernet 5/12 

Router(config-if)# switchport port-security mac-address sticky 

Configuring a Static Secure MAC Address on a Port

To configure a static secure MAC address on a port, perform this task:

•You can configure sticky secure MAC addresses if port security with sticky MAC addresses is enabled (see the "Enabling Port Security with Sticky MAC Addresses on a Port" section).

•The maximum number of secure MAC addresses on the port, configured with the switchport port-security maximum command, defines how many secure MAC addresses you can configure.

•If you configure fewer secure MAC addresses than the maximum, the remaining MAC addresses are learned dynamically.

•Port security is supported on trunks.

–On a trunk, you can configure a static secure MAC address in a VLAN.

–On a trunk, if you do not configure a VLAN for a static secure MAC address, it is secure in the VLAN configured with the switchport trunk native vlan command.

This example shows how to configure a MAC address 1000.2000.3000 as secure on Gigabit Ethernet port 5/12 and verify the configuration:

Router# configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)# interface gigabitethernet 5/12

Router(config-if)# switchport port-security mac-address 1000.2000.3000

Router(config-if)# end 

Router# show port-security address

          Secure Mac Address Table

------------------------------------------------------------

Vlan    Mac Address       Type                Ports

----    -----------       ----                -----

   1    1000.2000.3000    SecureConfigured     Gi5/12

Configuring Secure MAC Address Aging on a Port

•Configuring the Secure MAC Address Aging Type on a Port

•Configuring Secure MAC Address Aging Time on a Port

Note•Static secure MAC addresses and sticky secure MAC addresses do not age out.

•When the aging type is configured with the absolute keyword, all the dynamically learned secure addresses age out when the aging time expires. When the aging type is configured with the inactivity keyword, the aging time defines the period of inactivity after which all the dynamically learned secure addresses age out.

Configuring the Secure MAC Address Aging Type on a Port

You can configure the secure MAC address aging type on a port. To configure the secure MAC address aging type on a port, perform this task:

This example shows how to set the aging type to inactivity on Gigabit Ethernet port 5/12:

Router# configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)# interface gigabitethernet 5/12 

Router(config-if)# switchport port-security aging type inactivity 

Router(config-if)# do show port-security interface gigabitethernet 5/12 | include Type

Aging Type                 : Inactivity

Configuring Secure MAC Address Aging Time on a Port

To configure the secure MAC address aging time on a port, perform this task:

This example shows how to configure 2 hours (120 minutes) as the secure MAC address aging time on Gigabit Ethernet port 5/1:

Router# configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)# interface gigabitethernet 5/1 

Router(config-if)# switchport port-security aging time 120 

Router(config-if)# do show port-security interface gigabitethernet 5/12 | include Time

Aging Time                 : 120 mins

Verifying the Port Security Configuration

To display port security settings, enter this command:

•Port security supports the vlan keyword only on trunks.

•Enter the address keyword to display secure MAC addresses, with aging information for each address, globally for the switch or per interface.

•The display includes these values:

–The maximum allowed number of secure MAC addresses for each interface

–The number of secure MAC addresses on the interface

–The number of security violations that have occurred

–The violation mode

This example displays output from the show port-security command when you do not enter an interface:

Router# show port-security

Secure Port      MaxSecureAddr  CurrentAddr  SecurityViolation  Security Action

                    (Count)        (Count)      (Count)

----------------------------------------------------------------------------

     Gi5/1           11            11            0            Shutdown

     Gi5/5           15            5             0            Restrict

     Gi5/11          5             4             0            Protect

----------------------------------------------------------------------------

Total Addresses in System: 21

Max Addresses limit in System: 128

This example displays output from the show port-security command for a specified interface:

Router# show port-security interface gigabitethernet 5/1

Port Security: Enabled

Port status: SecureUp

Violation mode: Shutdown

Maximum MAC Addresses: 11

Total MAC Addresses: 11

Configured MAC Addresses: 3

Aging time: 20 mins

Aging type: Inactivity

SecureStatic address aging: Enabled

Security Violation count: 0

This example displays the output from the show port-security address privileged EXEC command:

Router# show port-security address

          Secure Mac Address Table

-------------------------------------------------------------------

Vlan    Mac Address       Type                Ports   Remaining Age

                                                         (mins)

----    -----------       ----                -----   -------------

   1    0001.0001.0001    SecureDynamic       Gi5/1      15 (I)

   1    0001.0001.0002    SecureDynamic       Gi5/1      15 (I)

   1    0001.0001.1111    SecureConfigured    Gi5/1      16 (I)

   1    0001.0001.1112    SecureConfigured    Gi5/1      -

   1    0001.0001.1113    SecureConfigured    Gi5/1      -

   1    0005.0005.0001    SecureConfigured    Gi5/5      23

   1    0005.0005.0002    SecureConfigured    Gi5/5      23

   1    0005.0005.0003    SecureConfigured    Gi5/5      23

   1    0011.0011.0001    SecureConfigured    Gi5/11     25 (I)

   1    0011.0011.0002    SecureConfigured    Gi5/11     25 (I)

-------------------------------------------------------------------

Total Addresses in System: 10

Max Addresses limit in System: 128

Tip For additional information about Cisco Catalyst 6500 Series Switches (including configuration examples and troubleshooting information), see the documents listed on this page:

http://www.cisco.com/en/US/products/hw/switches/ps708/tsd_products_support_series_home.html

Participate in the Technical Documentation Ideas forum