- Index
- Preface
- Overview
- Using the Command-Line Interface
- Configuring Switch Alarms
- Assigning the Switch IP Address and Default Gateway
- Configuring Cisco EnergyWise
- Configuring Cisco IOS Configuration Engine
- Clustering Switches
- Administering the Switch
- Configuring PTP
- Configuring SDM Templates
- Configuring Switch-Based Authentication
- Configuring IEEE 802.1x Port-Based Authentication
- Configuring Interface Characteristics
- Configuring Smartports Macros
- Configuring VLANs
- Configuring VTP
- Configuring Voice VLAN
- Configuring STP
- Configuring MSTP
- Configuring Optional Spanning-Tree Features
- Configuring Resilient Ethernet Protocol
- Configuring Flex Links and the MAC Address-Table Move Update Feature
- Configuring DHCP Features and IP Source Guard
- Configuring Dynamic ARP Inspection
- Configuring IGMP Snooping and MVR
- Configuring Port-Based Traffic Control
- Configuring LLDP, LLDP-MED, and Wired Location Service
- Configuring CDP
- Configuring UDLD
- Configuring SPAN and RSPAN
- Configuring RMON
- Configuring System Message Logging
- Configuring SNMP
- Configuring Network Security with ACLs
- Configuring Cisco IOS IP SLAs Operations
- Configuring QoS
- Configuring IPv6 Unicast Routing
- Configuring EtherChannels and Link-State Tracking
- Troubleshooting
- Supported MIBs
- Working with the Cisco IOS File System, Configuration Files, and Software Images
- Unsupported Commands in Cisco IOS Release 12.2(50)SE
Preface
Audience
This guide is for the networking professional managing the IE 3000 switch, hereafter referred to as the switch. Before using this guide, you should have experience working with the Cisco IOS software and be familiar with the concepts and terminology of Ethernet and local area networking.
Purpose
This guide provides the information that you need to configure Cisco IOS software features on your switch. This guide provides procedures for using the commands that have been created or changed for use with the switch. It does not provide detailed information about these commands. For detailed information about these commands, see the IE 3000 Switch Command Reference for this release. For information about the standard Cisco IOS Release 12.2 commands, see the Cisco IOS documentation set available from the Cisco.com home page at Documentation > Cisco IOS Software.
This guide does not provide detailed information on the graphical user interfaces (GUIs) for the embedded device manager or for Cisco Network Assistant (hereafter referred to as Network Assistant) that you can use to manage the switch. However, the concepts in this guide are applicable to the GUI user. For information about the device manager, see the switch online help. For information about Network Assistant, see Getting Started with Cisco Network Assistant, available on Cisco.com.
This guide does not describe system messages you might encounter or how to install your switch. For more information, see the IE 3000 Switch System Message Guide for this release and the IE 3000 Switch Hardware Installation Guide.
For documentation updates, see the release notes for this release.
Conventions
This publication uses these conventions to convey instructions and information:
Command descriptions use these conventions:
•Commands and keywords are in boldface text.
•Arguments for which you supply values are in italic.
•Square brackets ([ ]) mean optional elements.
•Braces ({ }) group required choices, and vertical bars ( | ) separate the alternative elements.
•Braces and vertical bars within square brackets ([{ | }]) mean a required choice within an optional element.
Interactive examples use these conventions:
•Terminal sessions and system displays are in screen
font.
•Information you enter is in boldface screen font.
•Nonprinting characters, such as passwords or tabs, are in angle brackets (< >).
Notes, cautions, and timesavers use these conventions and symbols:
Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual.
Related Publications
These documents provide complete information about the switch and are available from this Cisco.com site:
http://www.cisco.com/en/US/products/ps9703/tsd_products_support_series_home.html
Note Before installing, configuring, or upgrading the switch, see these documents:
•For initial configuration information, see the "Using Express Setup" section in the getting started guide or the "Configuring the Switch with the CLI-Based Setup Program" appendix in the hardware installation guide.
•For device manager requirements, see the "System Requirements" section in the release notes (not orderable but available on Cisco.com).
•For Network Assistant requirements, see the Getting Started with Cisco Network Assistant (not orderable but available on Cisco.com).
•For cluster requirements, see the Release Notes for Cisco Network Assistant (not orderable but available on Cisco.com).
•For upgrading information, see the "Downloading Software" section in the release notes.
See these documents for other information about the switch:
•Release Notes for the Cisco IE 3000 Switch
•Cisco IE 3000 Switch Software Configuration Guide
•Cisco IE 3000 Switch Command Reference
•Cisco IE 3000 Switch System Message Guide
•Device manager online help (available on the switch)
•Cisco IE 3000 Switch Hardware Installation Guide
•Cisco IE 3000 Switch Getting Started Guide
•Regulatory Compliance and Safety Information for the Cisco IE 3000 Switch
•Getting Started with Cisco Network Assistant
•Release Notes for Cisco Network Assistant
•Cisco Small Form-Factor Pluggable Modules Installation Notes
•For more information about the Network Admission Control (NAC) features, see the Network Admission Control Software Configuration Guide
•These compatibility matrix documents are available from this Cisco.com site:
http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html
–Cisco Gigabit Ethernet Transceiver Modules Compatibility Matrix
Obtaining Documentation, Obtaining Support, and Security Guidelines
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.