1288002 |
Message
|
SS7 link: %1, in service. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 link is now aligned and in service.
|
Action
|
No action is required.
|
1288003 |
Message
|
SS7 link: %1, out of service. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 link is now out of service. This is most likely due to a circuit problem between the NIC and the adjacent
signaling point to which this link connects. Equipment problems are also a possible cause. Because each link typically belongs
to a linkset containing two or more links, connectivity between the NIC and the adjacent signaling point is not lost unless
all other links in the linkset have failed. If this occurs, a "linkset unavailable" alarm is generated.
|
Action
|
Contact the technical assistance center.
|
128800A |
Message
|
SS7 linkset: %1, unavailable. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 linkset is now unavailable. This means that no links in that linkset are operational. Consequently, communication
has failed between the NIC and the adjacent signaling point to which the linkset connects.
|
Action
|
Contact the technical assistance center.
|
128800B |
Message
|
SS7 linkset: %1, available. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 linkset is now available. At least one link in the linkset is operational, although others may still be
down. Communication between the NIC and the adjacent signaling point to which the linkset connects has been restored.
|
Action
|
No action is required.
|
1288101 |
Message
|
BTNIC gateway online. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The NIC gateway has entered the online state. The routing client must now be configured, started, and brought online for
the NIC to become fully operational. This sequence will proceed automatically.
|
Action
|
No action is required.
|
1288102 |
Message
|
BTNIC gateway stopped: %1. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The NIC gateway has stopped operation due to the specified error code. All virtual circuits are blocked. The network should
adjust by sending calls to the router through an alternate path utilizing a different NIC. This can be caused by a communication
problem between the NIC and the router, by a problem with the router, or by an invalid NIC configuration.
|
Action
|
This event can be caused by a transient problem which may be automatically corrected as indicated by a "gateway online" event.
If the problem persists for more than three minutes, the technical assistance center should be alerted to investigate and
help correct the problem.
|
13F8200 |
Message
|
Session with client ID: %1, SCP index: %2, configuration valid. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
If a configuration error has occurred, it is cleared when the session is closed.
|
Action
|
No action is required.
|
13F8201 |
Message
|
Session with client ID: %1, SCP index: %2, configuration invalid. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
A problem has occurred with the capabilities or notification masks for this session. Either the mask sent in the open message
had undefined bits set or the router requested an action which was not configured in the open session message.
|
Action
|
Determine if the SCP is on line and if the communications links are available.
|
13F8202 |
Message
|
Session with client ID: %1, SCP index: %2, is now open. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
A session with the SCP is now open and available to carry traffic.
|
Action
|
No action is required.
|
13F8203 |
Message
|
Session with client ID: %1, SCP index: %2, is now closed. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
No session is currently opened with the SCP. The SCP index indicates the relative position of that SCP's configuration in
the Windows registry.
|
Action
|
Determine if the SCP is on line and if the communications links are available.
|
13F8206 |
Message
|
CRSP GATE online. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The CRSP NIC is online and is prepared to accept route requests from the network.
|
Action
|
No action is required.
|
13F8207 |
Message
|
CRSP GATE offline. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The CRSP NIC is offline and cannot accept route requests from the network.
|
Action
|
No action is required.
|
10D800A |
Message
|
SS7 linkset: %1, unavailable. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 linkset to the AT&T network is now in a non-working state. This means that all links (usually one, but
possibly more) between the NIC and a particular Signal Transfer Point (STP) in the AT&T network are not operational. This
is most likely due to a circuit problem in either the Local Exchange Carrier or in the AT&T network. Other possible causes
include equipment problems and maintenance procedures. Since the network interface utilizes two linksets, each connected to
a different STP, network connectivity is not impacted unless both linksets have failed. If this occurs, a "network inaccessible"
alarm will also be generated.
|
Action
|
Occasional brief outages of a single link (and hence a single linkset) are not unusual and require no action. If the outage
persists for more than five minutes, or if the outage occurs frequently, contact the AT&T Advanced Features Services Center
(AFDSC). Ask to speak to an ICP technician.
|
10D800B |
Message
|
SS7 linkset: %1, available. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 linkset to the AT&T network is now in a working state.
|
Action
|
No action is required.
|
10D8010 |
Message
|
SS7 network accessible; DPC: %1. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The interface to the AT&T network has returned to a working state. At least one link is now operational, although others
may still be down.
|
Action
|
No action is required.
|
10D8011 |
Message
|
SS7 network inaccessible; DPC: %1. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
All links to the AT&T network from the NIC originating this event are in a non-working state. If the links have not been
provisioned with physical diversity, then this outage could arise from a single circuit failure in the Local Exchange Carrier
or in the AT&T network. Failure of equipment common to all links is another possible cause, e.g., a T1 multiplexer or electrical
power circuit. If you have provisioned a second set of A-links, call routing may still be operational through this alternate
path for some or all of your 800 numbers, depending on your network routing configuration. Otherwise, all calls are being
default routed.
|
Action
|
Verify that you do not have an equipment failure at your site that could cause this problem. If the outage persists for more
than five minutes, or if the outage occurs frequently, contact the AT&T Advanced Features Service Center (AFSC). Ask to speak
to an ICP technician. If you have provisioned alternate A-links, use your AT&T network routing application, e.g. Routing Manager,
to redirect traffic to the alternate CRP which uses the alternate links.
|
10D8101 |
Message
|
ICP gateway online. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The NIC gateway has entered the online state. The routing client(s) must now be configured, started and brought online for
the NIC to become fully operational. This sequence will proceed automatically.
|
Action
|
No action is required.
|
10D8102 |
Message
|
NIC ICP gateway has stopped operation due to the following error: %1. Calls will be default routed. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The NIC ICP gateway has stopped operation due to the specified error code. Calls will be default routed. This can be caused
by a communication problem between the NIC and the router, by a problem with the router, or by an invalid NIC configuration.
|
Action
|
No action is required.
|
10D8106 |
Message
|
Routing client: %1, stopped: %2. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified rRouting client has stopped operation for the specified reason code. Calls for the associated subsystem/CRP-ID
will be default routed. This can be caused by a communication problem between the NIC and the router, by a problem with the
router, or by an invalid NIC configuration.
|
Action
|
This event can be caused by a transient problem which may be automatically corrected. If the problem persists for more than
five minutes, contact the technical assistance center.
|
10D8107 |
Message
|
Routing client: %1, online. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified routing client is now fully operational and able to process calls for the associated subsystem/CRP-ID.
|
Action
|
No action is required.
|
1340017 |
Message
|
Session for gateway: %1; connect failed to gateway at port: %2 at address: %3. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
INAP NIC was unable to connect to the gateway on the INAP network.
|
Action
|
Confirm that the gateway is available, that configuration of the IP address and the port are correct, and that network connectivity
would allow for connection.
|
1348009 |
Message
|
Gateway: %1, is now accessible. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The INAP NIC has established a communication session with the indicated gateway. This indicates that network connectivity
exists to the indicated gateway.
|
Action
|
No action is required.
|
134800A |
Message
|
Gateway: %1, is no longer accessible. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The INAP NIC has disconnected the communication sessions established with the indicated gateway.
|
Action
|
INAP network support should be contacted regarding this problem.
|
134800C |
Message
|
Gateway: %1, is not accessible. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
Although connected, the INAP NIC cannot establish a session with the indicated gateway.
|
Action
|
INAP network support should be contacted regarding this problem.
|
1348200 |
Message
|
INAPGATE online. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The INAP NIC is online and is prepared to accept route requests from the INAP network.
|
Action
|
No action is required.
|
1348201 |
Message
|
INAPGATE offline. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The INAP NIC is offline and cannot accept route requests from the INAP network.
|
Action
|
No action is required.
|
1368002 |
Message
|
SS7 link: %1; in service. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 link is now aligned and in service.
|
Action
|
No action is required.
|
1368003 |
Message
|
SS7 link: %1; out of service. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 link is now out of service. This is most likely due to a circuit problem between the INAP gateway and the
adjacent signaling point to which this link connects. Equipment problems are also a possible cause. Because each link typically
belongs to a linkset containing two or more links, connectivity between the INAP gateway and the adjacent signaling point
is not lost unless all other links in the linkset have failed. If this occurs, a "linkset unavailable" alarm is generated.
|
Action
|
Contact the technical assistance center.
|
136800A |
Message
|
SS7 linkset: %1; unavailable. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 linkset is now unavailable. This means that no links in that linkset are operational. Consequently, communication
has failed between the INAP gateway and the adjacent signaling point to which the linkset connects.
|
Action
|
Contact the technical assistance center.
|
136800B |
Message
|
SS7 linkset: %1; available. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 linkset is now available. At least one link in the linkset is operational, although others may still be
down. Communication between the INAP gateway and the adjacent signaling point to which the linkset connects has been restored.
|
Action
|
No action is required.
|
1368014 |
Message
|
SS7 link: %1, of linkset: %2, is in service. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 link is now aligned and in service.
|
Action
|
No action is required.
|
1368015 |
Message
|
SS7 link: %1, of linkset: %2, is out of service. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 link is now out of service. This is most likely due to a circuit problem between the INAP gateway and the
adjacent signaling point to which this link connects. Equipment problems are also a possible cause. Because each link typically
belongs to a linkset containing two or more links, connectivity between the INAP Gateway and the adjacent signaling point
is not lost unless all other links in the linkset have failed. If this occurs, a "linkset unavailable" alarm is generated.
|
Action
|
Contact the technical assistance center.
|
1368101 |
Message
|
INAP gateway online. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The INAP gateway has entered the online state. Traffic flow between the NIC and the SS7 network is enabled.
|
Action
|
No action is required.
|
1368102 |
Message
|
INAP gateway stopped; error: %1. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The INAP gateway has stopped operation due to the specified error code. The INAP subsystem is prohibited. The network should
adjust by sending calls to the router through an alternate path utilizing a different INAP gateway. This can be caused by
a communication problem between the INAP gateway and the NIC, by a problem with the router, or by an administrative INAP gateway
command.
|
Action
|
This event can be caused by a transient problem which may be automatically corrected as indicated by a "INAP gateway online"
event. If the problem persists for more than three minutes, the technical assistance center should be alerted to help investigate
and correct the problem.
|
1358004 |
Message
|
INRCEngine is initiating admission control; device ID: %1. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
Routing client engine is refusing new calls due to a larger than usual backlog of calls. This may be due to a problem in
the router. The routing client engine is now returning overload responses to new call requests and continuing to process existing
calls.
|
Action
|
If there is a problem in the router, it may be a transient problem that clears without intervention. If, however, the overload
condition does not end within three minutes, as indicated by an "terminating admission control" event, the technical assistance
center should be alerted to help investigate and correct the problem.
|
1358005 |
Message
|
INRCEngine is terminating admission control; device ID: %1. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The backlog of calls that caused Admission Control to be initiated has now been reduced to an acceptable level. Usual call
routing has resumed.
|
Action
|
No action is required.
|
135800A |
Message
|
INRCEngine is initiating restriction control for called party: %2; device ID: %1. |
Severity
|
Warning
|
Type
|
Raise
|
Description
|
Routing client engine is restricting the rate of new calls with the indicated called party number prefix due to a larger
than usual backlog of calls.
|
Action
|
No action is required.
|
135800B |
Message
|
INRCEngine is terminating restriction control on called party: %2; device ID: %1. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
Routing client engine is no longer restricting calls with the indicated called party number prefix.
|
Action
|
No action is required.
|
110800A |
Message
|
MCI RDG: %1 (%2) is now accessible. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The MCI NIC has established its first communication session with the indicated MCI remote data gateway. This indicates that
network connectivity exists to the indicated RDG.
|
Action
|
No action is required.
|
110800B |
Message
|
MCI RDG: %1 (%2) is either out of service or communications between ICM and the RDG has been broken. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The MCI NIC no longer has any communication sessions established with the indicated MCI remote data gateway. This points
to a problem with the indicated RDG, or a problem with network connectivity.
|
Action
|
The connection between the router and MCI has failed. If all remote data gateways (RDGs) are disconnected from the router
then ICM is not routing calls. MCI should be contacted for resolution.
|
1108200 |
Message
|
MCIGATE online. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The MCI NIC is online and is prepared to accept route requests from the MCI network.
|
Action
|
No action is required.
|
1108201 |
Message
|
MCIGATE offline. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The MCI NIC is offline and cannot accept route requests from the MCI network.
|
Action
|
No action is required.
|
12F8009 |
Message
|
SCP: %1:%2, is now accessible. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The NORTEL NIC has established a communication session with the indicated SCP. This indicates that network connectivity exists
to the indicated SCP.
|
Action
|
No action is required.
|
12F800A |
Message
|
SCP: %1:%2, is no longer accessible. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The NORTEL NIC has disconnected the communication sessions established with the indicated SCP.
|
Action
|
Nortel network support should be contacted regarding this problem.
|
12F800C |
Message
|
SCP: %1:%2, accessible but session to other side SCP: %1:%3, is still active. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The NORTEL NIC has established a communication session with the indicated SCP and side while a session to the other side
of the SCP is still active. This indicates that a failover situation to the SCP has occurred.
|
Action
|
Determine cause of failover.
|
12F8200 |
Message
|
NTGATE is online. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The NORTEL NIC is online and is prepared to accept route requests from the Nortel network.
|
Action
|
No action is required.
|
12F8201 |
Message
|
NTGATE is offline. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The NORTEL NIC is offline and cannot accept route requests from the Nortel network.
|
Action
|
No action is required.
|
1420017 |
Message
|
Session for gateway: %1, connect failed to gateway at port: %2, address: %3. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
CWC NIC was unable to connect to the gateway on the CWC network.
|
Action
|
Confirm gateway is available, configuration of IP address and port are correct, and network connectivity would allow for
connection.
|
1428009 |
Message
|
Gateway: %1, is now accessible. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The CWC NIC has established a communication session with the indicated gateway. This indicates that network connectivity
exists to the indicated gateway.
|
Action
|
No action is required.
|
142800A |
Message
|
Gateway: %1, is no longer accessible. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The CWC NIC has disconnected the communication sessions established with the indicated gateway.
|
Action
|
CWC network support should be contacted regarding this problem.
|
142800C |
Message
|
Gateway: %1, is not accessible. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
Although connected, the CWC NIC cannot establish a session with the indicated gateway.
|
Action
|
CWC network support should be contacted regarding this problem.
|
1428200 |
Message
|
C&W NIC routing client is online. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The CWC NIC is online and is prepared to accept route requests from the CWC network.
|
Action
|
No action is required.
|
1428201 |
Message
|
C&W NIC routing client is offline. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The CWC NIC is offline and cannot accept route requests from the CWC network.
|
Action
|
No action is required.
|
1428203 |
Message
|
SS7 link: %1, in service. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 link is now aligned and in service.
|
Action
|
No action is required.
|
1428204 |
Message
|
SS7 link: %1, out of service. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 link is now out of service. This is most likely due to a circuit problem between the INAP gateway and the
adjacent signaling point to which this link connects. Equipment problems are also a possible cause. Because each link typically
belongs to a linkset containing two or more links, connectivity between the INAP gateway and the adjacent signaling point
is not lost unless all other links in the linkset have failed. If this occurs, a "linkset unavailable" alarm is generated.
|
Action
|
Contact the technical assistance center.
|
142820B |
Message
|
SS7 linkset: %1, unavailable. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 linkset is now unavailable. This means that no links in that linkset are operational. Consequently, communication
has failed between the INAP Gateway and the adjacent signaling point to which the linkset connects.
|
Action
|
Contact the technical assistance center.
|
142820C |
Message
|
SS7 linkset: %1, available. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 linkset is now available. At least one link in the linkset is operational, although others may still be
down. Communication between the INAP Gateway and the adjacent signaling point to which the linkset connects has been restored.
|
Action
|
No action is required.
|
1428210 |
Message
|
INAP gateway online. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The INAP gateway has entered the online state. Traffic flow between the NIC and the SS7 network is enabled.
|
Action
|
No action is required.
|
1428211 |
Message
|
INAP gateway stopped: %1. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The INAP gateway has stopped operation due to the specified error code. The INAP subsystem is prohibited. The network should
adjust by sending calls to the router through an alternate path utilizing a different INAP gateway. This can be caused by
a communication problem between the INAP Gateway and the NIC, by a problem with the router, or by an administrative INAP gateway
command.
|
Action
|
This event can be caused by a transient problem which may be automatically corrected as indicated by a "INAP gateway online"
event. If the problem persists for more than three minutes, the technical assistance center should be alerted to investigate
and help correct the problem.
|
1428310 |
Message
|
SS7 link is out of service (Gateway PC: %1, Linkset RPC: %2, Link SLC: %3) (%4). |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 link is now out of service. This is most likely due to a circuit problem between the SS7 gateway and the
adjacent signaling point to which this link connects. Equipment problems are also a possible cause. Because each link typically
belongs to a linkset containing two or more links, connectivity between the SS7 gateway and the adjacent signaling point is
not lost unless all other links in the linkset have failed. If this occurs, a "linkset unavailable" alarm is generated.
|
Action
|
No action is required.
|
1428311 |
Message
|
SS7 link is in service (Gateway PC: %1, Linkset RPC: %2, Link SLC: %3). |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 link is now aligned and in service.
|
Action
|
No action is required.
|
1428312 |
Message
|
SS7 linkset unavailable (Gateway PC: %1, Linkset RPC: %2). |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 linkset is now unavailable. This means that no links in that linkset are operational. Consequently, communication
has failed between the SS7 gateway and the adjacent signaling point to which the linkset connects.
|
Action
|
Contact the technical assistance center.
|
1428313 |
Message
|
SS7 linkset available (Gateway PC: %1, Linkset RPC: %2). |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 linkset is now available. At least one link in the linkset is operational, although others may still be
down. Communication between the SS7 gateway and the adjacent signaling point to which the linkset connects has been restored.
|
Action
|
No action is required.
|
1460017 |
Message
|
Session for gateway: %1, connect failed to gateway: port: %2, address: %3. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
Unisource NIC was unable to connect to the gateway on the Unisource network.
|
Action
|
Confirm gateway is available, configuration of IP address and port are correct, and network connectivity would allow for
connection.
|
1468009 |
Message
|
Gateway: %1, is now accessible. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The Unisource NIC has established a communication session with the indicated gateway. This indicates that network connectivity
exists to the indicated gateway.
|
Action
|
No action is required.
|
146800A |
Message
|
Gateway: %1, is no longer accessible. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The Unisource NIC has disconnected the communication sessions established with the indicated gateway.
|
Action
|
Unisource network support should be contacted regarding this problem.
|
146800B |
Message
|
Gateway: %1, is not accessible. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
Although connected, the Unisource NIC cannot establish a session with the indicated gateway.
|
Action
|
Unisource network support should be contacted regarding this problem.
|
146800D |
Message
|
SS7 link: %1, in service. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 link is now aligned and in service.
|
Action
|
No action is required.
|
146800E |
Message
|
SS7 link: %1, out of service. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 link is now out of service. This is most likely due to a circuit problem between the SS7 gateway and the
adjacent signaling point to which this link connects. Equipment problems are also a possible cause. Because each link typically
belongs to a linkset containing two or more links, connectivity between the SS7 gateway and the adjacent signaling point is
not lost unless all other links in the linkset have failed. If this occurs, a "linkset unavailable" alarm is generated.
|
Action
|
Contact the technical assistance center.
|
1468015 |
Message
|
SS7 linkset: %1, unavailable. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 linkset is now unavailable. This means that no links in that linkset are operational. Consequently, communication
has failed between the SS7 gateway and the adjacent signaling point to which the linkset connects.
|
Action
|
Contact the technical assistance center.
|
1468016 |
Message
|
SS7 linkset: %1, available. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 linkset is now available. At least one link in the linkset is operational, although others may still be
down. Communication between the SS7 gateway and the adjacent signaling point to which the linkset connects has been restored.
|
Action
|
No action is required.
|
1468017 |
Message
|
SS7 gateway online. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The SS7 gateway has entered the online state. Traffic flow between the NIC and the SS7 network is enabled.
|
Action
|
No action is required.
|
1468018 |
Message
|
SS7 gateway stopped: %1. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The SS7 gateway has stopped operation due to the specified error code. The SS7 subsystem is prohibited. The network should
adjust by sending calls to the Router through an alternate path utilizing a different SS7 gateway. This can be caused by a
communication problem between the SS7 gateway and the NIC, by a problem with the Router, or by an administrative SS7 gateway
command.
|
Action
|
This event can be caused by a transient problem which may be automatically corrected as indicated by an "SS7 gateway online"
event. If the problem persists for more than three minutes, the technical assistance center should be alerted to help investigate
and correct the problem.
|
1468200 |
Message
|
UNISOURCE routing client is online. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The Unisource NIC is online and is prepared to accept route requests from the Unisource network.
|
Action
|
No action is required.
|
1468201 |
Message
|
UNISOURCE routing client is offline. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The Unisource NIC is offline and cannot accept route requests from the Unisource network.
|
Action
|
No action is required.
|
1468310 |
Message
|
SS7 link is out of service (gateway PC: %1, linkset RPC: %2, link SLC: %3): %4. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 link is now out of service. This is most likely due to a circuit problem between the SS7 gateway and the
adjacent signaling point to which this link connects. Equipment problems are also a possible cause. Because each link typically
belongs to a linkset containing two or more links, connectivity between the SS7 gateway and the adjacent signaling point is
not lost unless all other links in the linkset have failed. If this occurs, a "linkset unavailable" alarm is generated.
|
Action
|
No action is required.
|
1468311 |
Message
|
SS7 link is in service (gateway PC: %1, linkset RPC: %2, link SLC: %3). |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 link is now aligned and in service.
|
Action
|
No action is required.
|
1468312 |
Message
|
SS7 linkset unavailable (gateway PC: %1, linkset RPC: %2). |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 linkset is now unavailable. This means that no links in that linkset are operational. Consequently, communication
has failed between the SS7 gateway and the adjacent signaling point to which the linkset connects.
|
Action
|
Contact the technical assistance center.
|
1468313 |
Message
|
SS7 linkset available (gateway PC: %1, linkset RPC: %2). |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 linkset is now available. At least one link in the linkset is operational, although others may still be
down. Communication between the SS7 gateway and the adjacent signaling point to which the linkset connects has been restored.
|
Action
|
No action is required.
|
1468314 |
Message
|
SCTP connection is down (connection number: %1, remote entity: %2). |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The SCTP association to the remote entity is down. Communication has failed and calls cannot be processed through this connection.
Check the gateway logs for configuration errors and/or check the remote entity.
|
Action
|
No action is required.
|
1468315 |
Message
|
ASP is down (connection number: %1, remote entity: %2). |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The SCTP association to the remote entity is established, but the ASP is down. Calls cannot be processed through this connection.
Check the gateway logs for configuration errors and/or check the remote entity.
|
Action
|
No action is required.
|
1468316 |
Message
|
ASP is inactive (connection number: %1, remote entity: %2). |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The ASP is up, but is not yet active. Calls cannot be processed through this connection. Check the gateway logs for configuration
errors and/or check the remote entity.
|
Action
|
No action is required.
|
1468317 |
Message
|
ASP is active (connection number: %1, remote entity: %2). |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The ASP is active. Calls can be processed through this connection.
|
Action
|
No action is required.
|
1490017 |
Message
|
Session for gateway: %1, connect failed to gateway at port: %2, at address: %3. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
CONCERT NIC was unable to connect to the gateway on the CONCERT network.
|
Action
|
Confirm gateway is available, configuration of IP address and port are correct, and network connectivity would allow for
connection
|
1498009 |
Message
|
Gateway: %1, is now accessible. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The CONCERT NIC has established a communication session with the indicated gateway. This indicates that network connectivity
exists to the indicated gateway.
|
Action
|
No action is required.
|
149800A |
Message
|
Gateway: %1, is no longer accessible. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The CONCERT NIC has disconnected the communication sessions established with the indicated gateway.
|
Action
|
CONCERT network support should be contacted regarding this problem.
|
149800C |
Message
|
Gateway: %1, is not accessible. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
Although connected, the CONCERT NIC cannot establish a session with the indicated gateway.
|
Action
|
CONCERT network support should be contacted regarding this problem.
|
1498200 |
Message
|
CONCERTGATE onine. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The CONCERT NIC is online and is prepared to accept route requests from the CONCERT network.
|
Action
|
No action is required.
|
1498201 |
Message
|
CONCERTGATE offline. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The CONCERT NIC is offline and cannot accept route requests from the CONCERT network.
|
Action
|
No action is required.
|
1498203 |
Message
|
SS7 link: %1, in service. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 link is now aligned and in service.
|
Action
|
No action is required.
|
1498204 |
Message
|
SS7 link: %1, out of service. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 link is now out of service. This is most likely due to a circuit problem between the INAP gateway and the
adjacent signaling point to which this link connects. Equipment problems are also a possible cause. Because each link typically
belongs to a linkset containing two or more links, connectivity between the INAP gateway and the adjacent signaling point
is not lost unless all other links in the linkset have failed. If this occurs, a "linkset unavailable" alarm is generated.
|
Action
|
Contact the technical assistance center.
|
149820B |
Message
|
SS7 linkset: %1, unavailable. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 linkset is now unavailable. This means that no links in that linkset are operational. Consequently, communication
has failed between the INAP gateway and the adjacent signaling point to which the linkset connects.
|
Action
|
Contact the technical assistance center.
|
149820C |
Message
|
SS7 linkset: %1, available. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 linkset is now available. At least one link in the linkset is operational, although others may still be
down. Communication between the INAP gateway and the adjacent signaling point to which the linkset connects has been restored.
|
Action
|
No action is required.
|
1498210 |
Message
|
INAP gateway online. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The INAP gateway has entered the online state. Traffic flow between the NIC and the SS7 network is enabled.
|
Action
|
No action is required.
|
1498211 |
Message
|
INAP gateway stopped: %1. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The INAP gateway has stopped operation due to the specified error code. The INAP subsystem is prohibited. The network should
adjust by sending calls to the router through an alternate path utilizing a different INAP gateway. This can be caused by
a communication problem between the INAP gateway and the NIC, by a problem with the router, or by an administrative INAP gateway
command.
|
Action
|
This event can be caused by a transient problem which may be automatically corrected as indicated by a "INAP gateway online"
event. If the problem persists for more than three minutes, the technical assistance center should be alerted to investigate
and help correct the problem.
|
14C0017 |
Message
|
Session for gateway: %1, connect failed to gateway at port: %2, at address: %3. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
BT-V2 INAP NIC was unable to connect to the gateway on the INAP network.
|
Action
|
Confirm gateway is available, configuration of IP address and port are correct, and network connectivity would allow for
connection.
|
14C8009 |
Message
|
Gateway: %1, is now accessible. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The BT-V2 INAP NIC has established a communication session with the indicated gateway. This indicates that network connectivity
exists to the indicated gateway.
|
Action
|
No action is required.
|
14C800A |
Message
|
Gateway: %1, is no longer accessible. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The BT-V2 INAP NIC has disconnected the communication sessions established with the indicated gateway.
|
Action
|
INAP network support should be contacted regarding this problem.
|
14C800C |
Message
|
Gateway: %1, is not accessible. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
Although connected, the BT-V2 INAP NIC cannot establish a session with the indicated gateway.
|
Action
|
INAP network support should be contacted regarding this problem.
|
14C8200 |
Message
|
BT-V2 NIC routing client is online. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The BT-V2 INAP NIC is online and is prepared to accept route requests from the INAP network.
|
Action
|
No action is required.
|
14C8201 |
Message
|
BT-V2 NIC routing client is offline. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The BT-V2 INAP NIC is offline and cannot accept route requests from the INAP network.
|
Action
|
No action is required.
|
14C8203 |
Message
|
SS7 link: %1, in service. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 link is now aligned and in service.
|
Action
|
No action is required.
|
14C8204 |
Message
|
SS7 link: %1, out of service. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 link is now out of service. This is most likely due to a circuit problem between the INAP Gateway and the
adjacent signaling point to which this link connects. Equipment problems are also a possible cause. Because each link typically
belongs to a linkset containing two or more links, connectivity between the INAP Gateway and the adjacent signaling point
is not lost unless all other links in the linkset have failed. If this occurs, a "linkset unavailable" alarm is generated.
|
Action
|
Contact the technical assistance center.
|
14C820B |
Message
|
SS7 linkset: %1, unavailable. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 linkset is now unavailable. This means that no links in that linkset are operational. Consequently, communication
has failed between the INAP Gateway and the adjacent signaling point to which the linkset connects.
|
Action
|
Contact the technical assistance center.
|
14C820C |
Message
|
SS7 linkset: %1, available. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 linkset is now available. At least one link in the linkset is operational, although others may still be
down. Communication between the INAP gateway and the adjacent signaling point to which the linkset connects has been restored.
|
Action
|
No action is required.
|
14C8210 |
Message
|
INAP gateway online. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The INAP gateway has entered the online state. Traffic flow between the NIC and the SS7 network is enabled.
|
Action
|
No action is required.
|
14C8211 |
Message
|
INAP gateway stopped: %1. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The INAP gateway has stopped operation due to the specified error code. The INAP subsystem is prohibited. The network should
adjust by sending calls to the router through an alternate path utilizing a different INAP gateway. This can be caused by
a communication problem between the INAP gateway and the NIC, by a problem with the Router, or by an administrative INAP gateway
command.
|
Action
|
This event can be caused by a transient problem which may be automatically corrected as indicated by a "INAP gateway ONLINE"
event. If the problem persists for more than three minutes, the technical assistance center should be alerted to investigate
and help correct the problem.
|
14C8310 |
Message
|
SS7 link is out of service: gateway PC: %1, linkset RPC: %2, link SLC: %3; %4. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 link is now out of service. This is most likely due to a circuit problem between the SS7 gateway and the
adjacent signaling point to which this link connects. Equipment problems are also a possible cause. Because each link typically
belongs to a linkset containing two or more links, connectivity between the SS7 gateway and the adjacent signaling point is
not lost unless all other links in the linkset have failed. If this occurs, a "linkset unavailable" alarm is generated.
|
Action
|
No action is required.
|
14C8311 |
Message
|
SS7 link is in service: gateway PC: %1, linkset RPC: %2, link SLC: %3. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 link is now aligned and in service.
|
Action
|
No action is required.
|
14C8312 |
Message
|
SS7 linkset unavailable: gateway PC: %1, linkset RPC: %2. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 linkset is now unavailable. This means that no links in that linkset are operational. Consequently, communication
has failed between the SS7 gateway and the adjacent signaling point to which the linkset connects.
|
Action
|
Contact the technical assistance center.
|
14C8313 |
Message
|
SS7 linkset available: gateway PC; %1, linkset RPC: %2. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 linkset is now available. At least one link in the linkset is operational, although others may still be
down. Communication between the SS7 gateway and the adjacent signaling point to which the linkset connects has been restored.
|
Action
|
No action is required.
|
14D0017 |
Message
|
Session for gateway: %1, connect failed to gateway: port: %2, address: %3. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
TIM NIC was unable to connect to the gateway on the INAP network.
|
Action
|
Confirm gateway is available, configuration of IP address and port are correct, and network connectivity would allow for
connection.
|
14D8009 |
Message
|
Gateway: %1, is now accessible. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The TIM NIC has established a communication session with the indicated gateway. This indicates that network connectivity
exists to the indicated gateway.
|
Action
|
No action is required.
|
14D800A |
Message
|
Gateway: %1, is no longer accessible. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The TIM NIC has disconnected the communication sessions established with the indicated gateway.
|
Action
|
INAP network support should be contacted regarding this problem.
|
14D800C |
Message
|
Gateway: %1, is not accessible. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
Although connected, the TIM NIC cannot establish a session with the indicated gateway.
|
Action
|
INAP network support should be contacted regarding this problem.
|
14D8200 |
Message
|
TIM NIC routing client is online. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The TIM NIC is online and is prepared to accept route requests from the INAP network.
|
Action
|
No action is required.
|
14D8201 |
Message
|
TIM NIC routing client is offline. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The TIM NIC is offline and cannot accept route requests from the INAP network.
|
Action
|
No action is required.
|
14D8203 |
Message
|
SS7 link: %1, in service. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 link is now aligned and in service.
|
Action
|
No action is required.
|
14D8204 |
Message
|
SS7 link: %1, out of service. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 link is now out of service. This is most likely due to a circuit problem between the INAP gateway and the
adjacent signaling point to which this link connects. Equipment problems are also a possible cause. Because each link typically
belongs to a linkset containing two or more links, connectivity between the INAP gateway and the adjacent signaling point
is not lost unless all other links in the linkset have failed. If this occurs, a "linkset unavailable" alarm is generated.
|
Action
|
Contact the technical assistance center.
|
14D820B |
Message
|
SS7 linkset: %1, unavailable. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 linkset is now unavailable. This means that no links in that linkset are operational. Consequently, communication
has failed between the INAP gateway and the adjacent signaling point to which the linkset connects.
|
Action
|
Contact the technical assistance center.
|
14D820C |
Message
|
SS7 linkset: %1, available. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 linkset is now available. At least one link in the linkset is operational, although others may still be
down. Communication between the INAP gateway and the adjacent signaling point to which the linkset connects has been restored.
|
Action
|
No action is required.
|
14D8210 |
Message
|
INAP gateway online. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The INAP gateway has entered the online state. Traffic flow between the NIC and the SS7 network is enabled.
|
Action
|
No action is required.
|
14D8211 |
Message
|
INAP gateway stopped: %1. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The INAP gateway has stopped operation due to the specified error code. The INAP subsystem is prohibited. The network should
adjust by sending calls to the Router through an alternate path utilizing a different INAP gateway. This can be caused by
a communication problem between the INAP gateway and the NIC, by a problem with the Router, or by an administrative INAP gateway
command.
|
Action
|
This event can be caused by a transient problem which may be automatically corrected as indicated by a "INAP gateway online"
event. If the problem persists for more than three minutes, the technical assistance center should be alerted to investigate
and correct the problem.
|
14D8310 |
Message
|
SS7 link is out of service (gateway PC: %1, linkset RPC: %2, link SLC: %3): %4. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 link is now out of service. This is most likely due to a circuit problem between the SS7 gateway and the
adjacent signaling point to which this link connects. Equipment problems are also a possible cause. Because each link typically
belongs to a linkset containing two or more links, connectivity between the SS7 gateway and the adjacent signaling point is
not lost unless all other links in the linkset have failed. If this occurs, a "linkset unavailable" alarm is generated.
|
Action
|
No action is required.
|
14D8311 |
Message
|
SS7 link is in service (gateway PC: %1, linkset RPC: %2, link SLC: %3). |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 link is now aligned and in service.
|
Action
|
No action is required.
|
14D8312 |
Message
|
SS7 linkset unavailable (gateway PC: %1, linkset RPC: %2). |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 linkset is now unavailable. This means that no links in that linkset are operational. Consequently, communication
has failed between the SS7 gateway and the adjacent signaling point to which the linkset connects.
|
Action
|
Contact the technical assistance center.
|
14D8313 |
Message
|
SS7 linkset available (gateway PC: %1, linkset RPC: %2). |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 linkset is now available. At least one link in the linkset is operational, although others may still be
down. Communication between the SS7 gateway and the adjacent signaling point to which the linkset connects has been restored.
|
Action
|
No action is required.
|
14D8314 |
Message
|
SCTP connection is down (connection number: %1, remote entity: %2). |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The SCTP Association to the remote entity is down. Communication has failed and calls cannot be processed through this connection.
Check the gateway logs for configuration errors and/or check the remote entity.
|
Action
|
No action is required.
|
14D8315 |
Message
|
ASP is down (connection number: %1, remote entity: %2). |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The SCTP association to the remote entity is established, but the ASP is down. Calls cannot be processed through this connection.
Check the gateway logs for configuration errors and/or check the remote entity.
|
Action
|
No action is required.
|
14D8316 |
Message
|
ASP is inactive (connection number: %1, remote entity: %2). |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The ASP is up, but is not yet active. Calls cannot be processed through this connection. Check the gateway logs for configuration
errors and/or check the remote entity.
|
Action
|
No action is required.
|
14D8317 |
Message
|
ASP is active (connection number: %1, remote entity: %2). |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The ASP is active. Calls can be processed through this connection.
|
Action
|
No action is required.
|
14F0017 |
Message
|
Session for gateway: %1, connect failed to SS7 gateway; port: %2, address: %3. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
SS7 IN NIC was unable to connect to the SS7 gateway.
|
Action
|
Confirm SS7 gateway is available, configuration of IP address and port are correct, and network connectivity would allow
for connection.
|
14F8009 |
Message
|
SS7 gateway: %1, is now accessible. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The SS7 IN NIC has established a communication session with the SS7 gateway. This confirms that network connectivity exists
to the indicated SS7 gateway.
|
Action
|
No action is required.
|
14F800A |
Message
|
SS7 gateway: %1, is no longer accessible. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The SS7 IN NIC has disconnected the communication sessions established with the indicated SS7 gateway.
|
Action
|
SS7 network support should be contacted regarding this problem.
|
14F800C |
Message
|
SS7 gateway: %1, is not accessible. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
Although connected, the SS7 IN NIC cannot establish a session with the indicated gateway.
|
Action
|
SS7 network support should be contacted regarding this problem.
|
14F8102 |
Message
|
SS7 link: %1, in service. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 link is now aligned and in service.
|
Action
|
No action is required.
|
14F8103 |
Message
|
SS7 link: %1, out of service. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 link is now out of service. This is most likely due to a circuit problem between the SS7 gateway and the
adjacent signaling point to which this link connects. Equipment problems are also a possible cause. Because each link typically
belongs to a linkset containing two or more links, connectivity between the SS7 gateway and the adjacent signaling point is
not lost unless all other links in the linkset have failed. If this occurs, a "linkset unavailable" alarm is generated.
|
Action
|
Contact the technical assistance center.
|
14F810A |
Message
|
SS7 linkset: %1, unavailable. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 linkset is now unavailable. This means that no links in that linkset are operational. Consequently, communication
has failed between the SS7 gateway and the adjacent signaling point to which the linkset connects.
|
Action
|
Contact the technical assistance center.
|
14F810B |
Message
|
SS7 linkset: %1, available. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 linkset is now available. At least one link in the linkset is operational, although others may still be
down. Communication between the SS7 gateway and the adjacent signaling point to which the linkset connects has been restored.
|
Action
|
No action is required.
|
14F8114 |
Message
|
SS7 link: %1, of linkset: %2, is in service. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 link is now aligned and in service.
|
Action
|
No action is required.
|
14F8115 |
Message
|
SS7 link: %1, of linkset: %2, is out of service. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 link is now out of service. This is most likely due to a circuit problem between the SS7 gateway and the
adjacent signaling point to which this link connects. Equipment problems are also a possible cause. Because each link typically
belongs to a linkset containing two or more links, connectivity between the SS7 gateway and the adjacent signaling point is
not lost unless all other links in the linkset have failed. If this occurs, a "linkset unavailable" alarm is generated.
|
Action
|
Contact the technical assistance center.
|
14F8310 |
Message
|
SS7 link is out of service (gateway PC: %1, linkset RPC: %2, link SLC: %3): %4. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 link is now out of service. This is most likely due to a circuit problem between the SS7 gateway and the
adjacent signaling point to which this link connects. Equipment problems are also a possible cause. Because each link typically
belongs to a linkset containing two or more links, connectivity between the SS7 gateway and the adjacent signaling point is
not lost unless all other links in the linkset have failed. If this occurs, a "linkset unavailable" alarm is generated.
|
Action
|
No action is required.
|
14F8311 |
Message
|
SS7 link is in service (gateway PC: %1, linkset RPC: %2, link SLC: %3). |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 link is now aligned and in service.
|
Action
|
No action is required.
|
14F8312 |
Message
|
SS7 linkset unavailable (gateway PC: %1, linkset RPC: %2). |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The specified SS7 linkset is now unavailable. This means that no links in that linkset are operational. Consequently, communication
has failed between the SS7 gateway and the adjacent signaling point to which the linkset connects.
|
Action
|
Contact the technical assistance center.
|
14F8313 |
Message
|
SS7 linkset available (gateway PC: %1, linkset RPC: %2). |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The specified SS7 linkset is now available. At least one link in the linkset is operational, although others may still be
down. Communication between the SS7 gateway and the adjacent signaling point to which the linkset connects has been restored.
|
Action
|
No action is required.
|
14F8314 |
Message
|
SCTP connection is down (connection number: %1, remote entity: %2). |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The SCTP Association to the remote entity is down. Communication has failed and calls cannot be processed through this connection.
Check the gateway logs for configuration errors and/or check the remote entity.
|
Action
|
No action is required.
|
14F8315 |
Message
|
ASP is down (connection number: %1, remote entity: %2). |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The SCTP association to the remote entity is established, but the ASP is down. Calls cannot be processed through this connection.
Check the gateway logs for configuration errors and/or check the remote entity.
|
Action
|
No action is required.
|
14F8316 |
Message
|
ASP is inactive (connection number: %1, remote entity: %2). |
Severity
|
Error
|
Type
|
Raise
|
Description
|
The ASP is up, but is not yet active. Calls cannot be processed through this connection. Check the gateway logs for configuration
errors and/or check the remote entity.
|
Action
|
No action is required.
|
14F8317 |
Message
|
ASP is active (connection number: %1, remote entity: %2). |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The ASP is active. Calls can be processed through this connection.
|
Action
|
No action is required.
|
1504001 |
Message
|
The NTL NIC received an invalid label: %1. from the router for the call (tid: %2). |
Severity
|
Error
|
Type
|
Application Error
|
Description
|
The NTL NIC received an invalid label from the router. Check the label format and size.
|
Action
|
Check labels in the label table for invalid labels.
|
1508006 |
Message
|
Starting NTL network communications. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
The network communication layer of the NTL NIC is starting operation.
|
Action
|
No action is required.
|
1508007 |
Message
|
Stopping NTL network communications. |
Severity
|
Warning
|
Type
|
Raise
|
Description
|
The network communication layer of the NTL NIC is halting operation.
|
Action
|
No action is required.
|
1508009 |
Message
|
Starting a NTL communication channel: %1, with CE: %4:%2. |
Severity
|
Informational
|
Type
|
Clear
|
Description
|
A communication channel of the NTL NIC is starting operation.
|
Action
|
No action is required.
|
150800A |
Message
|
Stopping the NTL communication channel: %1, to CE: %4:%2. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
A communication channel of the NTL NIC is halting operation.
|
Action
|
No action is required.
|
150800B |
Message
|
Closing the NTL communication channel: %1, by CE: %4:%2. |
Severity
|
Error
|
Type
|
Raise
|
Description
|
A communication channel of the NTL NIC is closed by the SCP.
|
Action
|
No action is required.
|