PCC-Service-Profile Configuration Mode Commands

Mode

The PCC-Service-Profile Configuration Mode is used to define the business logic used by the operator for managing the policy requirements and objectives for the network specific to a group of subscribers in the network. A PCC-Service-Profile manages multiple PCC-Conditions-Groups and associated PCC-Action-Sets pairs in an ordered manner. A maximum of 32 PCC-Service-Profile can be configured in a PCC-Service instance.

Exec > Global Configuration > Context Configuration > PCC Service Configuration > PCC Service Profile Configuration

configure > context context_name > pcc-service service_name > profile profile_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-pcc-profile)#

Important

The commands or keywords/variables that are available are dependent on platform type, product version, and installed license(s).


Important

For information on common commands available in this configuration mode, refer to the Common Commands chapter.

default-rulebase-name

This command is used to associate the default PCC-Rulebase with a PCC-Service-Profile which is to use in Subscriber profile in PCC-Service instance on IPCF node.

Product

IPCF

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Context Configuration > PCC Service Configuration > PCC Service Profile Configuration

configure > context context_name > pcc-service service_name > profile profile_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-pcc-profile)#

Syntax

[no] default-rulebase-name rulebase_name

no

Removes the configured default PCC-Rulebase from PCC-Service-Profile instance on IPCF node.

rulebase_name

This keyword specifies the default PCC-Rulebase name to be associated with PCC-Service-Profile instance.

rulebase_name is the Rulebase name configured at PCEF and must be an alphanumeric string of 1 through 63 characters.

Usage Guidelines

Use this command to associate the default PCC-Rulebase configured on PCEF with a PCC-Service-Profile which is to use in Subscriber profile in PCC-Service instance on IPCF node.

Example

Following command associates the PCC-Rulebase named pcc_rulebase1 for PCC-Profile instance on IPCF node. 
default-rulebase-name pcc_rulebase1

eval-priority

This command sets the priority for evaluation of PCC-Condition-Group with corresponding PCC-Action-Set in a PCC-Service-Profile which is to use in Subscriber profile in PCC-Service instance on IPCF node.

Product

IPCF

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Context Configuration > PCC Service Configuration > PCC Service Profile Configuration

configure > context context_name > pcc-service service_name > profile profile_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-pcc-profile)#

Syntax

[no] eval-priority last action-set actionset_name 
[no] eval-priority priority_value timedef timedef_name [condition-group cond_grp_name] action-set actionset_name 
[no] eval-priority priority_value condition-group cond_grp_name action-set actionset_name

no

Removes the configured evaluation priority for PCC-Condition-Group with corresponding PCC-Action-Set from PCC-Service-Profile instance on IPCF node.

last

Sets last evaluation priority action-set configured for the PCC-Service-Profile instance.

no removes the last evaluation priority action-set.

priority_value

Specifies the priority to be set for PCC-Condition-Group with corresponding PCC-Action-Set in a PCC-Service-Profile instance.

priority_value must be an integer from 1 through 1023.

timedef timedef_name

Specifies a pre-configured time definition in PCC-Timedef Configuration mode and to be set for evaluation priority in a PCC-Service-Profile instance.

timedef_name is a pre-configured PCC-Timedef and must be an alphanumerical string of 1 through 63 characters.

condition-group cond_grp_name

Specifies a pre-configured PCC-Condition-Group to be set for evaluation priority in a PCC-Service-Profile instance.

cond_grp_name is a pre-configured PCC-Condition-Group and must be an alphanumerical string of 1 through 63 characters.


Important

An special PCC-Condition-Group "none" can be used to set the default PCC-Condition-Group for any-match typically used for a default condition for a session which does not match any of the conditions specified with higher evaluation priority.

action-set actionset_name

Specifies a pre-configured PCC-Action-Set for PCC-Condition-Group to be set for evaluation priority in a PCC-Service-Profile instance.

actionset_name is a pre-configured PCC-Action-Set and must be an alphanumerical string of 1 through 63 characters.

Usage Guidelines

Use this command to set the priority for evaluation of PCC-Condition-Group with corresponding PCC-Action-Set in a PCC-Service-Profile which is to use in Subscriber profile in PCC-Service instance on IPCF node.

Additionally timedef is used to accept the Timedefs to support the time-of-day-based procedures to trigger an evaluation priority. The action is triggered only when the time of session lies in the time span defined in specific PCC-Timedef timedef_name .

Default eval-priority has the lowest priority in the PCC-Service-Profile and as default eval-priority does not have any PCC-Condition-Group associated with it, all the actions in the action-set always be applied.

A maximum of 64 PCC-Evaluation-Priorities can be configured in a PCC-Service-Profile.

Example

Following command sets the evaluation priority value as 1 for PCC-Condition-Group cond_1 along with PCC-Action-Set act_cond1 for PCC-Service-Profile instance on IPCF node: 
eval-priority 1 condition-group cond_1 action-set act_cond1
Following command sets the evaluation priority value as 2 for PCC-Condition-Group none for any-match typically used for a default condition for a session which does not match any of the conditions specified with higher evaluation priority.along with PCC-Action-Set act_cond1 for PCC-Service-Profile instance on IPCF node: 
eval-priority 1 condition-group none action-set act_cond1

service-tag

This command configures the PCC-Service Tags to be used for PCC-Rulename or PCC-Rule-base in a PCC-Service-Profile which is to use in Subscriber profile in PCC-Service instance on IPCF node.

Product

IPCF

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Context Configuration > PCC Service Configuration > PCC Service Profile Configuration

configure > context context_name > pcc-service service_name > profile profile_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-pcc-profile)#

Syntax

[no] service-tag svc_tag {rule-name rule_name | rulebase-name rulebase_name}

no

Removes the configured PCC-Service Tags for PCC-Rulename and PCC-Rulebase from PCC-Service-Profile instance on IPCF node.

svc_tag

Specifies the name of the PCC-Service Tag to be used for PCC-Rulename and PCC-Rulebase in a PCC-Service-Profile instance.

svc_tag must be an alphanumerical string of 1 through 63 characters.

rule-name rule_name

Specifies a pre-defined PCC-Rulename on PCEF to be used with PCC-Service Tag svc_tag in a PCC-Service-Profile instance.

rule_name is a pre-defined PCC-Rulename on PCEF and must be an alphanumerical string of 1 through 63 characters.

rulebase-name rulebase_name

Specifies a pre-defined PCC-Rulebase name pre-defined on PCEF to be used with PCC-Service Tag svc_tag in a PCC-Service-Profile instance.

rulebase_name is a pre-defined PCC-Rulebase name on PCEF and must be an alphanumerical string of 1 through 63 characters.

Usage Guidelines

Use this command to set the PCC-Service Tag for PCC-Rulename and PCC-Rulebase which are defined on PCEF with a PCC-Service-Profile which is to use in Subscriber profile in PCC-Service instance.

Example

Following command sets the PCC-Service Tag named Rule1 for PCC-Rulebase named pcc_rulebase1 for PCC-Service-Profile instance on IPCF node: 
service-tag Rule1 rulebase-name pcc_rulebase1
Following command sets the PCC-Service Tag named Rule11 for PCC-Rulename pcc_rule1 for PCC-Service-Profile instance on IPCF node: 
service-tag Rule11 rule-name pcc_rule1

timeout long-duration

Configures the long duration timeout and inactivity duration for subscriber session before system notifies or terminates session in PCC Profile instance.

Product

IPCF

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Context Configuration > PCC Service Configuration > PCC Service Profile Configuration

configure > context context_name > pcc-service service_name > profile profile_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-pcc-profile)#

Syntax

timeout long-duration ldt_timeout [action {detection | disconnect}] 
no timeout long-duration 
default timeout long-duration

no

Removes the configured long duration timeout value and action in PCC Profile instance.

default

Sets the the long duration timeout value to the default value of '0' which disables the long duration timeout configuration in PCC Profile instance.

long-duration ldt_timeout

Default: 0

Designates the maximum duration of the session, in seconds, before the system automatically reports/terminates the session.

Specifies the maximum amount of time, in seconds, before the specified timeout action is activated.

ldt_timeout must be a value in the range from 0 through 4294967295.

The special value 0 disables the timeout specified.

action {detection | disconnect }

Default: Detection

Specifies the action to be taken on expiry of long duration timeout duration ldt_timeout set with timeout long-duration command.

  • detection : sets the system to detect the sessions for which long duration timeout timer is exceeded and sends the SNMP TRAP and CORBA notification. This is the default behavior.
  • disconnect : sets the system to send SNMP TRAP and CORBA notification and disconnect the subscriber session once the long duration timeout timer is expired.

Usage Guidelines

Use this command to set the long duration timeout period and actions to be taken on expiry of duration of timer for subscriber session.


Important
Reduce the timeout duration to free session resources faster for use by new requests.

Important

In case of long-duration timeout configured at PCC Service Configuration mode as well as at the PCC-Profile Configuration mode level, the long-duration timeout and action set in PCC-Profile Configuration mode will prevail. This enables defining session behavior as per profile provisioning.

Example

Following command sets the system to detect the subscriber sessions that exceeds the long duration timer of 6000 seconds and sends SNMP TRAP and CORBA notification: 
timeout long-duration 6000 action detection
Following command sets the system to detect and disconnect the subscriber sessions that exceeds the long duration timer of 6000 seconds and disconnect the session after sending SNMP TRAP and CORBA notification: 
timeout long-duration 6000 action disconnect

usage-monitor

This command creates/modifies/deletes the PCC-Usage-Monitor Configuration instance to track the usage volume across the PCC-services based on the usage monitor settings in a PCC-service instance for IPCF configuration.

Product

IPCF

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Context Configuration > PCC Service Configuration > PCC Service Profile Configuration

configure > context context_name > pcc-service service_name > profile profile_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-pcc-profile)#

Syntax

[no] usage-monitor usage_mon_name [-noconfirm]

no

Removes the configured PCC-Usage-Monitor from PCC-Service-Profile instance for IPCF configuration.

usage_mon_name

Identifies the name of the PCC-Usage-Monitor instance which is to be created or modified through this command.

The usage_mon_name must be an alphanumerical string from 1 through 63 characters.

-noconfirm

Indicates that the command is to execute without any additional prompt and confirmation from the user.


Caution

If this keyword option is used with no usage-monitor usage_mon_name command, the PCC-Usage-Monitor instance named usage_mon_name is deleted with all configured parameters without prompting any warning or confirmation.

Usage Guidelines

Use this command to create and configure a PCC-Usage-Monitor for PCC-Service-Profile in a PCC-service instance of IPCF configuration.

A maximum number of 8 PCC-Usage-Monitors can be configured per PCC-Service-Profile.

Entering this command results in the following prompt: 
[context_name]hostname(config-pcc-profile-usage-mon)#
The commands configured in this mode are defined in the PCC-Usage-Monitor Configuration Mode Commands chapter of Command Line Interface Reference.

Caution

This is a critical configuration. The PCC-Usage-Monitor for volume usage can not be configured without this configuration. Any change to this configuration would lead to removing or disabling configuration parameters defined here.

Example

Following command configures the PCC-Usage-Monitor named pcc_usage1 to track the usage of service with in a PCC-Service-Profile instance. 
usage-monitor pcc_usage1

unknown-services-treatment

This command configures the PCC-Service for handling of unknown services at IPCF which is to be used in Subscriber profile in PCC-Service instance on IPCF node.

Product

IPCF

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Context Configuration > PCC Service Configuration > PCC Service Profile Configuration

configure > context context_name > pcc-service service_name > profile profile_name

Entering the above command sequence results in the following prompt: 

[context_name]host_name(config-pcc-profile)#

Syntax

[default] unknown-services-treatment {not-allowed | qos-profile qos_prof_name precedence from start_preced to end_preced order {ascending | descending}}

default

Sets the configured PCC-Service for handling of unknown services at IPCF to default value of "Not allowed" which is to be used in Subscriber profile in PCC-Service instance on IPCF node.

not-allowed

Sets the PCC-Service-Profile instance to reject the packet filters and does not installs any dynamic rule when IPCF receives any request to authorize Packet Filters from PCEF and no matching service flow is found in data service list.

qos-profile qos_prof_name

Specifies a pre-defined PCC-QoS profile name to be used to create dynamic rule when IPCF receives any request to authorize Packet Filters from PCEF and no matching service flow is found in data service list.

qos_prof_name is a pre-defined PCC-QoS Profile and must be an alphanumerical string of 1 through 63 characters.

precedence from start_preced to end_preced

Specifies the precedence parameters to install dynamic rules for selection of QoS profile when QoS profile is configured to create dynamic rule when IPCF receives any request to authorize Packet Filters from PCEF and no matching service flow is found in data service list.

start_preced is an integer between 1 through 65535 and must be less than end_preced value where end_preced is an integer between 1 through 65535 and must be more than start_preced value

order {ascending | descending }

Specifies the order of precedence for QoS profile to be used to install dynamic rule when IPCF receives any request to authorize Packet Filters from PCEF and no matching service flow is found in data service list.

  • ascending sets the precedence setting in ascending order.
  • descending sets the precedence setting in descending order.

Usage Guidelines

Use this command to set the PCC-Service Tag for PCC-Rulename and PCC-Rulebase which are defined on PCEF with a PCC-Service-Profile which is to use in Subscriber profile in PCC-Service instance.

Whenever IPCF receives any request to authorize Packet Filters from PCEF, it does a lookup in data service list to find a match. If No service flow is found matching then the requested filters are treated as unknown service request and handled as per the mentioned configuration.

When unknown-service-treatment is set to not-allowed, then Packet Filters are rejected and no dynamic rule is installed. Otherwise, dynamic rule is created using the requested packet filters, data rates mentioned in the QoS profile name qos_prof_name and precedence value derived from the configured values.

The precedence configuration works in following manner:
  • If precedence limits are configured as 1000 to 2000 with order ascending then precedence of subsequent dynamic rules will go from 1000 to 2000.
  • If precedence limits are configured as 1000 to 2000 with order descending then precedence of subsequent dynamic rules will go from 2000 to 1000.

Example

Following command sets the PCC-Service for handling of unknown services for PCC-Service-Profile instance on IPCF node to default action of not allowed: 
default unknown-services-treatment