Command Line Interface Reference, Modes I - Q, StarOS Release 21.23

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents

Find Matches in This Book

Results

Updated:: March 31, 2021

Chapter: Local Policy Service Configuration Mode Commands

Local Policy Service Configuration Mode Commands
actiondef
eventbase
ruledef
suppress-cra

Local Policy Service Configuration Mode Commands

Important

A maximum of 16 local QoS policy services are supported.

Mode

The Local Policy Service Configuration Mode is used to configure the local QoS policy for one or more services.

Exec > Global Configuration > Local Policy Service Configuration

configure > local-policy-service service_name

Entering the above command sequence results in the following prompt:

[context_name]host_name(config-local-policy-service)#

Important

The commands or keywords/variables that are available are dependent on platform type, product version, and installed license(s).

Important

For information on common commands available in this configuration mode, refer to the Common Commands chapter.

actiondef

This command enables creating, configuring, or deleting action definitions for an event.

Product

P-GW

SAEGW

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Local Policy Service Configuration

configure > local-policy-service service_name

Entering the above command sequence results in the following prompt:

[context_name]host_name(config-local-policy-service)#

Syntax

actiondef actiondef_name [ -noconfirm ] 
no actiondef actiondef_name

no

Deletes the specified actiondef from the local QoS policy service.

`actiondef_name`

Specifies name of the actiondef.

actiondef_name must be unique within the service expressed as an alphanumeric string of 1 through 63 characters.

If the named actiondef does not exist, it is created, and the CLI mode changes to the Local Policy Actiondef Configuration Mode wherein the actiondef can be configured.

If the named actiondef already exists, the CLI mode changes to the Local Policy Actiondef Configuration Mode for that actiondef.

-noconfirm

Specifies that the command must execute without prompting for confirmation.

Usage Guidelines

Use this command to create, configure, or delete an actiondef. The actiondef configuration is used to configure the action definitions for an event. The event ruledef will have one or more rules and associated action(s).

This command can be entered multiple times to specify multiple actiondefs.

Important

A maximum of 256 actiondefs are suggested in a local QoS policy service for performance reasons. An actiondef can be referenced by multiple eventbases.

Entering this command results in the following prompt:

[context_name]hostname(config-local-policy-actiondef)#

Local Policy Actiondef Configuration Mode commands are defined in the Local Policy Actiondef Configuration Mode Commands chapter.

Example

The following command creates an actiondef named actiondef1 and enters the Local Policy Actiondef Configuration Mode:

actiondef actiondef1

eventbase

This command enables creating, configuring, or deleting an eventbase.

Product

P-GW

SAEGW

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Local Policy Service Configuration

configure > local-policy-service service_name

Entering the above command sequence results in the following prompt:

[context_name]host_name(config-local-policy-service)#

Syntax

eventbase eventbase_name [ -noconfirm ] 
no eventbase eventbase_name

no

Deletes the specified eventbase from the local QoS policy service.

`eventbase_name`

Specifies name of the eventbase.

eventbase_name must be unique within the service expressed as an alphanumeric string of 1 through 63 characters.

Important

Currently, only one eventbase is supported, and it must be named "default".

If the named eventbase does not exist, it is created, and the CLI mode changes to the Local Policy Eventbase Configuration Mode wherein the eventbase can be configured.

If the named eventbase already exists, the CLI mode changes to the Local Policy Eventbase Configuration Mode for that eventbase.

-noconfirm

Specifies that the command must execute without prompting for confirmation.

Usage Guidelines

Use this command to create, configure, or delete an eventbase.

Entering this command results in the following prompt:

[context_name]hostname(config-local-policy-eventbase)#

Local Policy Eventbase Configuration Mode commands are defined in the Local Policy Eventbase Configuration Mode Commands chapter.

Example

The following command creates an eventbase named default and enters the Local Policy Eventbase Configuration Mode:

eventbase default

ruledef

This command enables creating, configuring, or deleting a rule definition.

Product

P-GW

SAEGW

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Local Policy Service Configuration

configure > local-policy-service service_name

Entering the above command sequence results in the following prompt:

[context_name]host_name(config-local-policy-service)#

Syntax

ruledef ruledef_name [ -noconfirm ] 
no ruledef ruledef_name

no

Deletes the specified ruledef from the local QoS policy service.

`ruledef_name`

Specifies name of the ruledef.

ruledef_name must be unique within the service expressed as an alphanumeric string of 1 through 63 characters.

If the named ruledef does not exist, it is created, and the CLI mode changes to the Local Policy Ruledef Configuration Mode wherein the ruledef can be configured.

If the named ruledef already exists, the CLI mode changes to the Local Policy Ruledef Configuration Mode for that ruledef.

-noconfirm

Specifies that the command must execute without prompting for confirmation.

Usage Guidelines

Use this command to create, configure, or delete a ruledef. A ruledef represents a set of matching conditions.

This command can be entered multiple times to specify multiple ruledefs.

Important

A maximum 256 ruledefs are suggested in a local QoS policy service for performance reasons.

Entering this command results in the following prompt:

[context_name]hostname(config-local-policy-ruledef)#

Local Policy Ruledef Configuration Mode commands are defined in the Local Policy Ruledef Configuration Mode Commands chapter.

Example

The following command creates a ruledef named rule5 and enters the Local Policy Ruledef Configuration Mode:

ruledef rule5

suppress-cra

This command allows to suppress the Change Reporting Action (CRA) for event triggers enabled in local policy configurations.

Product

GGSN

P-GW

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > Local Policy Service Configuration

configure > local-policy-service service_name

Entering the above command sequence results in the following prompt:

[context_name]host_name(config-local-policy-service)#

Syntax

suppress-cra event-triggers { ecgi-change | tai-change | uli-change } + 
no suppress-cra

no

This variant is used to configure the default behavior. By default, the CRA notification is sent to MME if one or a combination of these event triggers is installed.

suppress-cra event-triggers { ecgi-change | tai-change | uli-change } +

This keyword restricts sending of CRA towards MME depending on the ECGI-Change, TAI-Change and ULI-Change event triggers configured in local-policy service.

Usage Guidelines

Use this command to control the CRA notification towards MME based on the configured event triggers in the local-policy configuration.

Example

The following command suppresses CRA if ECGI-Change event trigger is installed:

suppress-cra event-triggers ecgi-change

Was this Document Helpful?

Feedback

Contact Cisco

Open a Support Case
(Requires a Cisco Service Contract)