N4 Interface Configuration

This chapter covers the following topics:

Feature Summary and Revision History

Summary Data

Table 1. Summary Data
Applicable Product(s) or Functional Area 5G-UPF
Applicable Platform(s)

VPC-SI

SMI

Feature Default Setting Disabled - Configuration Required
Related Changes in this Release Not Applicable
Related Documentation UCC 5G UPF Configuration and Administration Guide

Revision History

Table 2. Revision History
Revision Details Release
New IEs are supported in UPF in compliance with 3GPP TS 29.244. 2021.01.0
First introduced. 2020.02.0

Feature Description

This chapter provides the configuration information to identify a peer node to be an N4 interface, and the configuration to modify N4 parameters in an Sx-Service.

Configuring N4 Interface

This section describes the following configurations:

  • Identifying N4 Interface

  • Adding N4-type and Modification of N4 Parameters in Sx Service

Identifying an N4 Interface

Use the following configuration to identify if a peer node is an N4 interface type.


configure 
   control-plane-group group_name 
      peer-node-id [ ipv4-address ipv4_address | ipv6-address ipv6_address ] interface n4 
      end 

NOTES:

  • To enable the n4 interface CLI command, you need the require upf CLI command on the UPF, which depends on the UPF license.

  • [ ipv4-address ipv4_address | ipv6-address ipv6_address ] :

    ipv4-address ipv4_address : Specifies the IPv4 address of the peer node.

    ipv6-address ipv6_address : Specifies the IPv6 address of the peer node.

  • interface n4 : Identifies the N4 interface.

Modification of N4-type Parameters in an Sx Service

Use the following configuration to modify N4-type parameters in an Sx Service.


configure 
   context context_name 
      sx-service service_name 
         n4 [ max-retransmissions max_retransmission_value | retransmission-timeout-ms timeout_value ] 
         end 

NOTES:

  • n4 : Allows modifications to N4 parameters.

  • [ max-retransmissionsmax_retransmission_value | retransmission-timeout-ms timeout_value] :

    max-retransmissions max_retransmission_value Configures maximum retries for Sx control packets. max_retransmission_value must be an integer in the range of 0 to 15. The default value is 4.

    retransmission-timeout-ms : Configures the control packet retransmission timeout in Sx in milliseconds. timeout_value must be an integer in the range of 1000 to 20000 milliseconds. The timeout value must be configured in steps of 100; for example: 1000, 1100, 1200, and so on. The default value is 5000 milliseconds.

Statistics

This section provides information on show commands and their output available in support of this feature.

show control-plane-group

The output of this command displays the following fields for this feature:

  • Interface Type – This field indicates if the peer interface is N4. It is not displayed for non-N4 interfaces.

show sx-service all

The output of this command displays the following fields for this feature:

  • N4

    • N4 Retransmission Timeout

    • N4 Maximum Request Retransmission

show subscribers user-plane-only all

The output of this command displays the following fields for this feature:

  • Interface

    • N4

show user-plane-service statistics all

The output of this command displays the following fields for this feature:

  • N4 interface-type PDNs

    • Active

    • Setup

    • Released

show subscribers user-plane-only seid number pdr all

The output of this command displays the following fields for this feature:

  • Associated-QFIs

show subscribers user-plane-only callid number pdr full all

The output of this command displays the following fields for this feature:

  • QoS Flow Identifier