Table Of Contents

Subscriber Template Settings

Overview: Subscriber Template Settings

Template Setup

Subscriber Template Profile Settings

Subscriber Template Account Settings

Subscriber Template Passwords Settings

Subscriber Template Conversation Settings

Subscriber Template Call Transfer Settings

Subscriber Template Greetings Settings

Subscriber Template Caller Input Settings

Subscriber Template Messages Settings

Subscriber Template Distribution Lists Settings

Subscriber Template Message Notification Settings

Subscriber Template Settings

---

Overview: Subscriber Template Settings

When you create subscriber accounts in Cisco Unity, you can base each account on a subscriber template. Subscriber templates contain settings that are appropriate for most subscribers of a particular type (such as a department). Basing new subscribers on a template minimizes the number of settings that must be modified on individual subscriber accounts, making the job of adding subscribers easier.

Template Setup

Most settings applied by the template can be changed, when necessary, in individual subscriber accounts. However, you will want to take care when setting up a template to make choices that will keep the changes that you will need to make after the subscribers are added to a minimum. If changes are needed in an individual account, subscribers can change some of the settings themselves; other settings must be changed by you. Note that changes to settings in a template do not affect any of the existing subscriber accounts that were based on that template.

Cisco Unity comes with a predefined subscriber template called {Default Subscriber}, which you can modify but not delete. You can also create an unlimited number of additional templates.

To create a new template

---

Step 1 Go to any Subscribers > Subscriber Template page.

Step 2 Click the Add icon.

Step 3 In the Add a Subscriber Template dialog box, enter information as appropriate in the Name field.

Step 4 Select New Template or Based on Existing Template. If you select Based on Existing Template, select the appropriate template in the Based On field.

Step 5 Click the Add button.

Step 6 Enter settings for your new template, and then click the Save icon.

---

To modify a template

---

Step 1 Go to any Subscribers > Subscriber Template page.

Step 2 Click the Find icon.

Step 3 Double-click the template that you want to modify.

Step 4 Change settings as appropriate, and then click the Save icon.

---

Refer to the following sections in this chapter for more information:

•Subscriber Template Profile Settings—This section provides information about the settings on the Profile page.

•Subscriber Template Account Settings—This section provides information about the settings on the Account page.

•Subscriber Template Passwords Settings—This section provides information about the settings on the Passwords page.

•Subscriber Template Conversation Settings—This section provides information about the settings on the Conversation page.

•Subscriber Template Call Transfer Settings—This section provides information about the settings on the Call Transfer page.

•Subscriber Template Greetings Settings—This section provides information about the settings on the Greetings page.

•Subscriber Template Caller Input Settings—This section provides information about the settings on the Caller Input page.

•Subscriber Template Messages Settings—This section provides information about the settings on the Messages page.

•Subscriber Template Distribution Lists Settings—This section provides information about the settings on the Distribution Lists page.

•Subscriber Template Message Notification Settings—This section provides information about the settings on the Message Notification page.

Subscriber Template Profile Settings

Profile settings define how Cisco Unity identifies a subscriber. Some of these settings are defined in the subscriber template, but most are defined in the Cisco Unity account for each individual subscriber.

Use the following table to learn more about subscriber template profile settings.

Table 12-1 Subscribers > Subscriber Template > Profile Page

Field	Considerations
Name	This displays the name of the template. To change the name of the template, enter a new name here, and then click the Save icon.
Class of Service	Select the class of service to which subscribers are assigned. The class of service defines permissions and restrictions for using Cisco Unity. To view the details of the selected class of service, click the View link. Note that when you click the link, you leave the Subscribers > Subscriber Template > Profile page, and move to the Subscribers > Class of Service > Profile page.
Active Schedule	Select a schedule to specify the days and times that the standard and closed subscriber greetings play, as well as the action that Cisco Unity takes after the greeting. To view details of the selected schedule, click the View link. Note that when you click the link, you leave the Profile page, and move to the System > Schedules page.
Time Zones	Select the desired time zone for the subscriber. The default time zone setting is Default, which is the time zone set on the Cisco Unity server. Change this setting only for those subscribers who are located in a different time zone than the Cisco Unity server. The subscriber time zone setting is used for: •The Message Received Time—When a subscriber listens to messages over the phone, Cisco Unity announces the time that a message was received by using the local time specified for the subscriber. •The Message Notification Schedule—The schedule displayed on the subscriber Message Notification page and in the ActiveAssistant uses the local time specified for the subscriber. Note that even if you change the time zone setting for a subscriber, the time zone setting on the Cisco Unity server is used to determine when standard and closed greetings are played for callers.
Switch (for dual-switch integrations only)	Select the phone system that the subscriber uses. If this setting is incorrect, Cisco Unity will not be able to: •Transfer calls to or from the subscriber. •Turn message waiting indicators (MWIs) on or off. •Dial the extension assigned to the subscriber for Media Master recording by phone. On the System > Ports page, the selected phone system must have an appropriate number of ports set to answer calls and to dial out for MWIs and Media Master recording by phone.
Display Name Generation	Select the format for displaying the names of new subscribers. Choose either First Name Then Last Name (Jessie Smith) or Last Name Then First Name (Smith, Jessie). The format selected here should be consistent with the Exchange name generation rule for existing Exchange mailboxes. If your organization uses a format other than those listed, you must select one of these options anyway, then manually adjust the display name in each subscriber account.
Set Subscriber for Self-Enrollment at Next Login	Check this box so that the subscriber will be asked at the next logon to record a name and a standard greeting, to set a password, and to choose whether to be listed in directory assistance. Once the subscriber has enrolled, the check box is unchecked automatically. This setting is most commonly used for new subscribers.
List in Phone Directory	Check this box to list the subscriber in directory assistance, which callers can use to reach subscribers. When allowed by the class of service, subscribers can change this setting over the phone or by using the ActiveAssistant.
Exchange Alias Generation	Select a format for new subscriber aliases. This format applies only when a Windows account for the subscriber does not already exist. A Windows account and Exchange mailbox are created when the Cisco Unity account is created. The format selected here should be consistent with the Exchange alias rule for existing Exchange mailboxes. If your organization uses a format other than those listed, you can choose None. You then must specify the alias for each subscriber that you add. Or you can first create new subscribers in Exchange and then import them into Cisco Unity with the correct alias. Cisco Unity checks that the alias is unique when the subscriber record is saved.

Subscriber Template Account Settings

You can use account settings to lock all subscriber accounts and to provide a billing ID.

Use the following table to learn more about subscriber template account settings.

Table 12-2 Subscribers > Subscriber Template > Account Page

Field	Considerations
Cisco Unity Account Status	Check this box to lock subscriber accounts that are associated with this template; uncheck it to unlock the account(s). When an account is locked, no one can access the account by phone, but the subscriber can access it by using the ActiveAssistant.
Billing ID	Enter organization-specific information, such as accounting information, department names, or project codes. This information can be included in subscriber reports.

Subscriber Template Passwords Settings

Password settings define whether subscribers can set and change their own phone passwords. When you set up the account policy to require subscribers to have passwords, you set a default password in the subscriber template and then require new subscribers to change the password the next time they log on. Note that the phone password is separate from any password a subscriber uses to log on to Windows.

See Chapter 17, "Account Policy Settings" for more information about account policy.

Use the following table to learn more about subscriber template passwords settings.

Table 12-3 Subscribers > Subscriber Template > Passwords Page

Field	Considerations
User Cannot Change Password	Check this box to prevent the subscriber from changing the phone password. Use of this setting is most appropriate for accounts that can be accessed by more than one person. When you check this box, also check the Password Never Expires check box.
User Must Change Password at Next Login	Check this box when a temporary phone password has been created for new employees.
Password Never Expires	Check this box for low-security subscribers or for accounts that can be accessed by more than one person. Uncheck the box to require the subscriber to change the phone password at the interval specified on the Subscribers > Account Policy > Phone Password Restrictions page.
Phone Password for New Subscribers	Enter a password by using digits 0 through 9. All new subscribers who will be based on this template will be assigned this password when added. The minimum length of the password depends on settings on the Subscribers > Account Policy > Phone Password Restrictions page. To have Cisco Unity prompt subscribers to create confidential passwords, also check the User Must Change Password at Next Login check box.
Last Phone Password Change	Display only. This setting shows the date that the password was last changed.
Password for New Windows NT Accounts	Enter a temporary Windows password for all new subscribers whose accounts will be based on this template. This password gives subscribers access to the Windows domain.
Last Windows NT Password Change	Display only. This setting shows the date that the Windows password was last changed.

Subscriber Template Conversation Settings

The subscriber conversation is a set of prerecorded instructions and options that Cisco Unity plays over the phone to subscribers when they listen to, send, and manage messages, and as they change their Cisco Unity settings. The conversation settings define some of what subscribers hear and how they hear it in the subscriber conversation.

Use the following table to learn more about subscriber template conversation settings.

Table 12-4 Subscribers > Subscriber Template > Conversation Page

Field	Considerations
Greet Subscriber by Name	Check this box to have Cisco Unity play the recorded name of the subscriber when the subscriber accesses Cisco Unity by phone. Uncheck the box to have Cisco Unity go directly to the message count.
Conversation Type	Choose one of these options: •Full Menus—Subscribers hear comprehensive instructions; select for a new subscriber. •Brief Menus—Subscribers hear abbreviated versions of the full menus; select for a more experienced subscriber.
Subscriber's Language	Select the language in which the subscriber conversation plays instructions to the subscriber. This setting also controls the language used for text-to-speech e-mail. (Note that to use text-to-speech e-mail, your organization must have purchased text-to-speech e-mail licenses and installed the appropriate TTS languages. Text-to-speech e-mail is controlled by class of service.)
Address Messages to Other Subscribers	Select how subscribers address messages to other subscribers. Subscribers can address messages over the phone by entering recipient extensions, by spelling their first names, or by spelling their last names. Addressing by name requires lettered keypads on subscriber phones. In the subscriber conversation, subscribers can switch between addressing by name and addressing by extension by pressing the # key twice.
Announce Total Number of New Messages	Check this box to have Cisco Unity announce the total number of unopened messages. The number includes voice, e-mail, fax, and return receipt messages.
Announce Total Number of Saved Messages	Check this box to have Cisco Unity announce the total number of messages that have been opened but not deleted. The number includes voice, e-mail, fax, and return receipt messages.
Announce Total Number of New Voice Messages	Check this box to have Cisco Unity announce the number of voice messages that have not been heard.
Announce Total Number of New Fax Messages	Check this box to have Cisco Unity announce the number of unopened fax messages.
Announce Total Number of New E-Mail Messages	Check this box to have Cisco Unity announce the number of unopened e-mail messages.
Announce Sender	Check this box to have Cisco Unity announce the name of the sender, if the message is from an identified subscriber.
Say Message Number	Check this box to have Cisco Unity announce the sequential number of a message ("Message one is..."). Use with the Announce Total Number of New Messages check box to help the subscriber keep track of the number of unheard messages.
Announce Time Stamp Before Messages	Check this box to have Cisco Unity announce the date and time a message was sent, before playing the message.
Announce Time Stamp After Message	Check this box to have Cisco Unity announce the date and time a message was sent, after playing the message.
Volume Level	Select the volume level at which the subscriber hears the Cisco Unity conversation. Subscribers can also adjust the volume temporarily from their phones.

Subscriber Template Call Transfer Settings

Call transfer settings specify whether external calls are transferred to a phone or to the greetings of a subscriber or handler. These settings also specify how Cisco Unity handles a transfer: Cisco Unity can either release the call to the phone system, or it can supervise the transfer.

When Cisco Unity is set to supervise transfers, it can provide additional call control with call holding and call screening:

•With call holding, when the phone is busy, Cisco Unity can ask callers to hold. Cisco Unity plays hold music, and approximately every 30 seconds, tells callers on hold how many callers are ahead of them and allows them to continue holding, leave a message, or try another extension. There is no limit to the number of callers that can be holding.

If call holding is not selected, callers are sent to whichever subscriber or handler greeting is enabled—either the busy, standard, closed, or alternate greeting.

•With call screening, Cisco Unity can ask for the name of the caller before connecting to a subscriber. The subscriber can then hear who is calling and, when a phone is shared by more than one subscriber, who the call is for. The subscriber can then accept or refuse the call.

Use the following table to learn more about subscriber template call transfer settings.

Table 12-5 Subscribers > Subscriber Template > Call Transfer Page

Field	Considerations
Transfer Incoming Calls to Subscriber's Phone	Choose one of these options: •No (Send Directly)—The extension assigned to the subscriber does not ring for external calls; Cisco Unity plays the subscriber greeting. •Yes, Ring Subscriber's Extension—Cisco Unity sends calls to the extension assigned to the subscriber (displayed in the adjacent box). •Yes, Ring Subscriber at This Number—Cisco Unity sends calls to the number entered in the adjacent box. Note that the restriction tables associated with your class of service may prohibit you from entering certain phone numbers.
Transfer Type	Select how Cisco Unity transfers calls. Use this setting with caution and only if you understand its implications on the phone and voice messaging systems. •Release to Switch—Cisco Unity puts the caller on hold, dials the extension, and releases the call to the phone system. When the line is busy or is not answered, the phone system—not Cisco Unity—forwards the call to the subscriber or handler greeting. This transfer type allows Cisco Unity to process incoming calls more quickly. Use Release to Switch only when call forwarding is enabled on the phone system. •Supervise Transfer—Cisco Unity acts as a receptionist, handling the transfer. If the line is busy or the call is not answered Cisco Unity—not the phone system—forwards the call to the subscriber or handler greeting. You can use supervised transfer whether or not the phone system forwards calls. The Transfer Type option is unavailable when Transfer Incoming Calls is set to the No (Send Directly) option.
Rings to Wait For	Select the number of times the extension rings before Cisco Unity plays the subscriber or handler greeting. Set this value to at least 3 to give subscribers a chance to answer. Avoid setting to more than 4, especially if the call may be transferred to another extension, where the caller might have to wait for another four rings. This value should be at least two rings fewer than the phone system setting for forwarding calls. This option is unavailable when Release to Switch is selected and when Transfer Incoming Calls is set to the No (Send Directly) option.
If the Call Is Busy	Select the action that Cisco Unity performs for external calls when the subscriber phone is busy. You may want to use holding options sparingly, because having calls on hold can tie up ports. •Always Hold—Cisco Unity plays a prompt indicating that the extension is busy. The caller is put on hold. •No Holding—Cisco Unity prompts the caller to leave a message and allows the caller to dial another extension. •Ask Caller—Cisco Unity gives the caller the options of holding, leaving a message, or dialing another extension. These options are unavailable when Release to Switch is selected and when Transfer Incoming Calls is set to the No (Send Directly) option.
Announce	Check this box to have Cisco Unity say "transferring call" when the subscriber answers the phone, to indicate that the call is from an unidentified caller. This option is unavailable when Release to Switch is selected and when Transfer Incoming Calls is set to the No (Send Directly) option.
Introduce (Call for Name)	Check this box to have Cisco Unity say "call for <subscriber recorded name>" or "call for <dialed extension number>" when the subscriber answers the phone. This setting applies only to calls from unidentified callers. Use this setting when subscribers share a phone or a subscriber takes calls for more than one dialed extension. This option is unavailable when Release to Switch is selected and when Transfer Incoming Calls is set to the No (Send Directly) option.
Confirm (Call Can Be Accepted or Refused)	Check this box to have Cisco Unity prompt the subscriber to accept or refuse a call from an unidentified caller. If the call is accepted, it is transferred to the subscriber phone. If the call is refused, Cisco Unity plays the appropriate subscriber greeting. You use this setting with the Ask Caller's Name setting to allow the subscriber to screen calls. This option is unavailable when Release to Switch is selected and when Transfer Incoming Calls is set to the No (Send Directly) option.
Ask Caller's Name	Check this box to have Cisco Unity prompt unidentified callers to say their names. When the phone is answered, the subscriber hears "Call from..." before Cisco Unity transfers the call. You use this setting with the Confirm setting to allow the subscriber to screen calls. This option is unavailable when Release to Switch is selected and when Transfer Incoming Calls is set to the No (Send Directly) option.

Subscriber Template Greetings Settings

Each subscriber and call handler can have up to five greetings. The greeting settings specify which greetings are enabled and the actions that Cisco Unity takes during and after each greeting. Enabling a greeting makes it available for Cisco Unity to use in appropriate situations.

The greeting that plays when a caller reaches a subscriber or call handler depends on:

•The active schedule.

•The greeting source.

•Whether the call is internal.

•Whether the called extension is busy.

Cisco Unity greetings for subscribers and call handlers are:

Standard	Plays at all times unless overridden by another greeting.
Closed	Plays during the closed (nonbusiness) hours defined for the active schedule. When in effect, the closed greeting overrides the standard greeting, and thus limits the standard greeting to the open hours defined for the active schedule.
Internal	Plays to internal callers only. It can provide information that only coworkers need to know. (For example, "I will be in the lab all afternoon.") An internal greeting overrides the standard and closed greetings. Not all phone system integrations provide the support necessary for an internal greeting. Note that the internal greeting must be enabled and recorded from the Cisco Unity Administrator or the ActiveAssistant; subscribers cannot access it over the phone.
Busy	Plays when the extension is busy. (For example, "All of our operators are with other customers.") A busy greeting overrides the standard, closed, and internal greetings. Not all phone system integrations provide the support necessary for a busy greeting. Note that the busy greeting must be enabled and recorded from the Cisco Unity Administrator or the ActiveAssistant; subscribers cannot access it over the phone.
Alternate	Can be used for a variety of special situations, such as vacations or a holiday. (For example, "I will be out of the office until....") An alternate greeting overrides all other greetings.

Use the following table to learn more about subscriber template greeting settings.

Table 12-6 Subscribers > Subscriber Template > Greetings Page

Field	Considerations
Greeting	Select the greeting that you want to specify settings for. This setting does not reflect which of the greetings is active.
Status	Indicate whether the selected greeting is enabled. When a greeting is enabled, Cisco Unity plays it in the appropriate situation. Recording a greeting does not automatically enable it; it must be enabled here.
Source	Indicate the source for the greeting selected in the Greeting field: •System—Select to use the prerecorded system default greeting. •Recording—Select to use a personal recording for the subscriber (or call handler). To record and play recordings here, use the Media Master control bar. (Note that the Media Master is not available across a firewall.) Use the Options menu in the Media Master control bar to set recording and playback devices, if applicable, and to use other sound files. •Blank—Select to have no recording. When the greeting source is left blank, Cisco Unity immediately performs the after-greeting action.
Allow Caller Input	Check this box to enable settings specified on the Caller Input page. These settings contain actions assigned to caller key presses during the greeting. (For example, "To speak to my assistant, press 3.") Click the Caller Input link to view the Caller Input page. Note that when you click the link, you leave the Greetings page.
After Greeting	Indicate the action that Cisco Unity performs after the greeting plays: •Take Message—Cisco Unity records a message from the caller. Click the Take Message link to view the Messages page. •Say Good-Bye—Cisco Unity plays a brief good-bye, and the call is disconnected. Click the Say Good-Bye link to view the Good-Bye call handler. •Send Caller To—Cisco Unity sends the call to the destination that you select: –Call Handler—Sends the call to the call handler that you select. –Directory Handler—Sends the call to directory assistance. –Hang Up—Disconnects the call. Use carefully; unexpected hang-ups can appear rude to callers. –Interview Handler—Sends the call to the interview handler that you select. –Sign-In—Sends the call to the subscriber logon conversation. –Subscriber—Sends the call to the subscriber that you select.
Reprompt the User After This Many Seconds of Silence	Check this box and enter a value in the field on the right to indicate the number of seconds of silence to allow. When Cisco Unity receives no input from a caller within this number of seconds, Cisco Unity prompts the caller again.
Number of Times to Reprompt	Indicate the number of times to reprompt a caller. After the number of times indicated here, Cisco Unity performs the after-greeting action.

Subscriber Template Caller Input Settings

Caller input settings define actions that Cisco Unity takes in response to touchtone keys pressed by callers. For Cisco Unity to recognize caller input, the Allow Caller Input check box must be checked on the Greetings page.

Caller input settings are available only in the Cisco Unity Administrator; however, the greeting that mentions the key presses can be recorded either by the subscriber or the administrator. (For example, "I am unable to take your call right now. To speak to my assistant, press 3. To leave a message, press 4. To speak to a sales representative, press 5.")

To define an action for a key

---

Step 1 Select a key from the Caller Input Map or from the keypad.

Step 2 Select an action.

Step 3 Indicate whether to lock the key to that action.

---

Use the following table to learn more about subscriber template caller input settings.

Table 12-7 Subscribers > Subscriber Template > Caller Input Page

Field	Considerations
Allow Callers to Dial an Extension During Greeting	Check this box to allow callers to enter an extension while the greeting plays. Use in conjunction with the Lock This Key check box to allow callers to enter some extensions but not others. This option is unavailable if the Allow Caller Input check box is unchecked on the Greetings page.
Milliseconds to Wait for Additional Digits	Indicate the amount of time Cisco Unity waits for additional input after callers press a single key that is not locked. If there is no input within this time, Cisco Unity performs the action assigned to the single key. A value of 1500 (one and one-half seconds) is recommended. This option is unavailable if the Allow Callers to Dial check box is unchecked.
Lock This Key to the Action	Check this box to have Cisco Unity ignore additional input after callers press the key; Cisco Unity performs the action assigned to the key. To create efficient caller input menus, lock all keys except those that begin extensions on your system. You also can lock a key to block calls to extensions that begin with that key. To lock the actions for all keys, uncheck the Allow Callers to Dial check box.
Action	Indicate the action that Cisco Unity performs after a caller presses the corresponding key. For Cisco Unity to recognize caller input, the Allow Caller Input check box must be checked on the Greetings page. •Ignore Key—No action taken. Cisco Unity plays the entire greeting, then performs the after-greeting action. •Skip Greeting—Cisco Unity skips the greeting and performs the after-greeting action. Skip Greeting is assigned to # by default to provide callers a standard way to skip greetings. •Take Message—Cisco Unity records a message from the caller. The greeting should indicate that a message will be recorded. Click the Take Message link to view the associated Messages page. •Say Good-Bye—Cisco Unity plays a brief good-bye, and the call is disconnected. Click the Say Good-Bye link to view the Good-Bye call handler. •Send Caller To—Cisco Unity sends the call to the destination that you select: –Call Handler—Sends the call to the call handler that you select. –Directory Handler—Sends the call to directory assistance. –Hang Up—Disconnects the call. Use carefully; unexpected hang-ups can appear rude to callers. –Interview Handler—Sends the call to the interview handler that you select. –Sign-In—Sends the call to the subscriber logon conversation. –Subscriber—Sends the call to the subscriber that you select.

Subscriber Template Messages Settings

Message settings define the following:

•The maximum recording length for messages from external callers.

•What external callers can do when leaving messages.

•The language of the Cisco Unity prompts that callers hear when leaving messages.

•Whether subscribers are notified that they have messages.

Use the following table to learn more about subscriber template messages settings.

Table 12-8 Subscribers > Subscriber Template > Messages Page

Field	Considerations
Maximum Message Length in Seconds	Set the recording length allowed for messages left by unidentified callers. Recipients may want to limit the length of messages from unidentified callers. Some departments, such as Customer Service, may want to permit much longer messages.
After Message Action	Indicate the action that Cisco Unity performs after an unidentified caller leaves a message: •Say Good-Bye—Cisco Unity plays a brief good-bye, and the call is disconnected. Click the Say Good-Bye link to view the Good-Bye call handler. •Send Caller To—Cisco Unity sends the call to the destination that you select: –Call Handler—Sends the call to the call handler that you select. –Directory Handler—Sends the call to directory assistance. –Hang Up—Disconnects the call. Use carefully; unexpected hang-ups can appear rude to callers. –Interview Handler—Sends the call to the interview handler that you select. –Sign-In—Sends the call to the subscriber logon conversation. –Subscriber—Sends the call to the subscriber that you select.
Callers Can Edit Messages	Check this box to allow callers to be prompted to listen to, add to, rerecord, or delete their messages. Balance giving callers the additional control of editing messages with having voice messaging ports tied up for the additional time.
Mark Messages as Urgent	Indicate the action that Cisco Unity will allow: •Always—All messages left by unidentified callers are marked urgent. This may be useful for Sales or Technical Support call handlers. •Never—Messages left by unidentified calls are never marked urgent. •Ask Caller for Their Preference—Cisco Unity asks unidentified callers whether to mark their messages urgent. Note that Cisco Unity plays new urgent messages before other messages.
Language That Callers Hear	Select the language in which system prompts are played to callers. The language setting affects system prompts such as "You may record your message at the tone." If you choose Inherited, Cisco Unity determines the language to use for system prompts on a per-call basis, depending upon the language set by the handler or routing rule that processed the call. If the language is set to Inherited for every rule and handler that processes a call, then the system prompts are played in the default phone language. The default phone language and the list of languages shown here are set on the System > Configuration > Phone Languages page.
Use MWI for Message Notification	Check this box to have Cisco Unity use the message waiting indicator (MWI) on the phone to alert the subscriber of new voice messages. MWIs are not used to indicate new e-mail, fax, or return receipt messages.
Extension	When the Use MWI for Message Notification field is enabled, Cisco Unity uses the number listed in the table to activate a message waiting indicator (MWI). By default, the table contains an "X" to indicate the primary extension assigned to a subscriber. You can change this to have Cisco Unity activate MWIs for another extension or phone number. Enter digits 0 through 9. Do not use spaces, dashes, or parentheses between digits. You can also enter: •, (comma) to insert a one-second pause. •# and * to correspond to the # and * keys on the phone.

Subscriber Template Distribution Lists Settings

Distribution list settings allow you to specify which public distribution lists subscribers will be assigned to. For example, you might create different templates for different work groups, and create a public distribution list for each work group.

Cisco Unity automatically creates a public distribution list called All Subscribers. You may want to associate the All Subscribers list with every subscriber template.

Create the public distribution lists before setting up subscriber templates if you plan to associate public distribution lists with templates. After the subscriber accounts are created, you can add or remove subscribers from the lists on the Public Distribution Lists > Profile Page.

Use the following table to learn more about distribution list settings.

Table 12-9 Subscribers > Subscriber Template > Distribution Lists

Field	Considerations
Public Distribution Lists	A list of all public distribution lists that are not currently associated with the selected template. To assign all new subscribers based on this template to a public distribution list, select the list and click >>.
New Subscribers Added To	All public distribution lists to which new subscribers are added. To assign all new subscribers based on this template to a public distribution list, select the list in the Public Distribution Lists box and click >>. To remove a distribution list from those to which new subscribers are added, select the list and click <<.

Subscriber Template Message Notification Settings

Cisco Unity can notify a subscriber of new messages by calling a phone or pager, or by sending an e-mail. Message notification settings allow you to control how and when Cisco Unity notifies a subscriber of new messages. To set up message notification, you select a notification device—phone, pager, or text pager—and enter a phone number or e-mail address, as appropriate. The settings for each device allow you to control when and how notifications are sent to the first and subsequent devices. For example, message notification can be set to "chain" to subsequent notification devices if an attempt to send notification to the first device fails (either the device is busy or does not answer). Additionally, you can set up "cascading message notification," which allows you to send notifications to a widening circle of recipients if the first recipient does not save or delete the new message.

You can set up notification for subscribers by using the Cisco Unity Administrator, and subscribers can set it up themselves by using the ActiveAssistant, if available. Subscribers can also enter the phone number and status of four of the devices—home phone, work phone, spare phone, and pager—in the subscriber phone conversation.

Generally, you adjust message notification settings on the message notification page of a specific subscriber and not in the subscriber template. However, you may want to enter notification settings in the subscriber template if, for example, you want to set up chaining or cascading message notification for an entire department of new subscribers.

Use the following table to learn more about subscriber template message notification settings.

Table 12-10 Subscribers > Subscriber Template > Message Notification Page

Field	Considerations
Device	Select the device that you want to use for message notification.
Phone Number	Enter the phone number, including trunk access code, of the selected device. Use digits 0 through 9 and the following dialing characters in the phone number: •, (comma) to insert a one-second pause. •# and * to correspond to the # and * keys on the phone. Subscribers can change this number over the phone. Note that the restriction tables associated with your class of service may prohibit you from entering certain phone numbers.
Extra Digits	Enter any extra digits that Cisco Unity will dial after the phone number. The effect of the extra digits depends on the selected device. For pagers, the extra digits are shown on the pager display.
Dialing Options	Select the dialing options: •Try to Detect Connection—Cisco Unity waits until detecting a connection to dial the digits in Extra Digits. •Seconds to Wait—Cisco Unity can wait a specified number of seconds before dialing the digits in Extra Digits. Use this option if the automatic call progress detection is not reliable. Examples of poor call progress detection include noisy phone lines and unusual ringing patterns.
To: (E-Mail Address) (for text pager notifications only)	Enter the e-mail address of the subscriber text pager, text-compatible cell phone, or another e-mail account (such as a home e-mail address). Up to 128 characters can be entered in this field.
From: (Phone Number) (for text pager notifications only)	Enter a phone number in this field if the subscriber has a text-compatible cell phone and wants text pager notifications to include a return phone number. Typically, this field contains the number of the subscriber Cisco Unity account. The From phone number appears in the last line of any text pager notification. A subscriber can press the Return Call button on many text-compatible cell phones to dial the phone number. The cell phone must support automatic callback in order to use this feature. Up to 40 characters can be entered in this field.
Send: (for text pager notifications only)	Enter the text message that the subscriber wants to receive in a text pager notification. For example, you might enter "Urgent message for Technical Support" for a subscriber who is on call for the technical support department. Every time a message arrives that matches the criteria selected in the message notification settings, the Cisco Unity Messaging System sends this text message. Up to 64 characters can be entered in this field.
Include Voice Mail, E-Mail, and Fax Message Counts (for text pager notifications only)	Check this box if you want the text pager notification to include a count of each voice mail, e-mail, and fax message. When you receive the text pager notification, the message count appears as a line for each type of message. For example: •9 voice mail •2 urgent voice mail •17 urgent e-mail The e-mail count does not include non-delivery receipts or meeting requests.
Status	Indicate whether to turn message notification to this device on or off. Subscribers can change this setting over the phone. •Enabled—Cisco Unity calls the device when there are new messages. •Disabled—Cisco Unity does not call the device. Disabling a device does not delete its settings.
Notify Subscriber Of	Select the types of messages and message urgency for which Cisco Unity will call the device. If no message type is selected, Cisco Unity does not call the device. When setting up a chain of message notification devices, select messages in this field only for the first device. If any message types are selected for any device other than the first, message notification for this device will commence immediately and will not wait for the notification failure of the previous device. Therefore, your notifications will not chain but all trigger at once.
Notification Schedule	In the grid, click the blocks to change between inactive (no notifications) and active (notifications okay). Note that you can set active and inactive hours for one day, then use Copy Day's Schedule to copy the settings to other days.
Copy Day's Schedule	To avoid clicking the same blocks for more than one day, use the Copy Day's Schedule and >> functions. Select a day to copy, then select which days to copy the schedule setting to.
Notification Options: Send Initial Notification After How Many Minutes	Specify the delay from the time a message is received until the message notification triggers (if the message matches the criteria selected in the Notify Subscriber Of section). You can space notifications on different devices at regular intervals, such as 15 minutes, to achieve a cascading message notification effect. If the delay time takes the notification out to a time when the device schedule is no longer active, the notification does not take place. The range for the delay field is 0 to 120 minutes. The default is 0 minutes.
Notification Options: Restart Notification or Repeat Notification	Use to specify the timing of message notification according to subscriber needs. Choose one of these options: •Restart Notification Each Time a New Message Arrives—When this option is selected, Cisco Unity begins a notification process immediately upon the arrival of each message that matches the selected criteria. Cisco Unity considers notification successful if the device answers, even if new messages remain. (For example, notification is considered successful even when an answering machine picks up and records the message, but the message remains unread in the subscriber Inbox.) Note that if you activate the Restart Notification option and the Send Initial Notification field is set to 0, then Cisco Unity triggers the message notification immediately. However, if you enter a delay in the Send Initial Notification field, then Cisco Unity delays notification that number of minutes instead of dialing immediately. Messages that arrive during the delay period will not trigger separate notifications. •Repeat Notification If There Are Still New Messages After This Many Minutes—When this option is selected and a duration specified, Cisco Unity attempts notification immediately after the first message, and then initiates a notification schedule based on the specified interval. For example, if you set the repeat notification interval to 5 minutes at 11:47 a.m., Cisco Unity will notify the subscriber of new messages at 11:50 a.m., 11:55 a.m., 12:00 p.m., 12:05 p.m., 12:10 p.m., 12:15 p.m., 12:20 p.m., 12:25 p.m., etc. The notification schedule is effective for as long as the subscriber has one or more new messages. The range for the redial frequency field is 1 to 100 minutes.
If Device Does Not Answer (not available for text pager notifications)	Indicate settings for the following: •Wait for How Many Rings Before Hanging Up—Set to a minimum of 3 rings. Choose a higher number to give a subscriber more time to get to the phone. •Try Again How Many Times—Choose a higher number to reach a subscriber who steps away from the phone briefly. Choose a lower number to avoid disturbing others. •How Many Minutes to Wait Between Tries—Choose a higher number to reach a subscriber who is away from the phone for long periods of time.
If Device Is Busy (not available for text pager notifications)	Indicate settings for the following: •Try Again How Many Times—Choose a higher number to reach a subscriber who uses the phone frequently. •How Many Minutes to Wait Between Tries—Choose a higher number to reach a subscriber who has long phone conversations.
If Notification Fails, Send Notification To (not available for text pager notifications)	Select an option for an additional device to send notification to when the first device does not answer or is busy, and the maximum number of retries has been reached. Cisco Unity calls the next device only if it is enabled and its schedule is current. Cisco Unity considers message notification successful if a device answers, even if, for example, an answering machine answers. Cisco Unity considers that message notification has failed only after all selected no-answer and busy signal retries have been exhausted.
Switch (for dual-switch integrations only)	Select the phone system that Cisco Unity dials out on when notifying the subscriber of new messages. Each notification device (except for text pagers) can be associated with a specific phone system. On the System > Ports page, the selected phone system must have at least one port set to dial out for message notification.